ENVIRONMENTAL ENGINEERING-I - PDF Free Download

ENVIRONMENTAL ENGINEERING-I Prof. Rajesh Bhagat Asst. Professor Civil Engineering Department Yeshwantrao Chavan College Of Engineering Nagpur B. E. (Civil Engg.) M. Tech. (Enviro. Engg.) GCOE, Amravati VNIT, Nagpur Mobile No.:- 8483003474 / 8483002277 Email ID:- rajeysh7bhagat@gmail.com Website:- www.rajeysh7bhagat.wordpress.com

UNIT-IV 1) Sedimentation: Principles types of setting basins, inlet and outlet arrangements. 2) Clariflocculators: Principles and operation. 3) Filtration: Mechanism of filtration, types of filters RSF, SSF, pressure filters, elements of filters, UDS, design aspects of filter and operational problems in filtration.

Sedimentation 1) Discrete or granular particle are those which do not change their size, shape & weight. 2) Settling- process by which particulates settle to the bottom of a liquid and form a sediment. 3) The other type of particles are those which change their size, shape & weight and thus loose their identity. 4) The basin in which the flow of water is retarded or storage is offered is called the settling tank or sedimentation tank or basin or clarifier. 5) The average time theoretically for which the water is detained in the tank is called detention period. 6) Sedimentation is process by which the suspended particles that are heavier than water are removed by gravitational settling. 7) Sedimentation process can remove 60% of SS & 75% of bacteria. 8) Floatation is a process by which lighter particles can remove.

Factors Affecting Sedimentation: 1) Flow velocity 2) Viscosity of water 3) Temperature 4) Size of particle 5) Shape of particle 6) Specific gravity of particle Characteristics of the particles Size and shape Specific gravity Properties of the water Specific gravity Viscosity Physical environment of the particle Velocity of the water Inlet and outlet arrangements of the structure

Advantages of Sedimentation:- Simplest technologies Little energy input Relatively inexpensive to install and operate No specialized operational skills Easily incorporated into new or existing facilities Disadvantages of Sedimentation:- Low hydraulic loading rates Poor removal of small suspended solids Large floor space requirements Re-suspension of solids.

Types of Sedimentation Tank A. Depending upon shape: 1) Circular 2) Rectangular 3) Square B. Depending on process of operation: 1) Continuous Tank: Flow velocity of water is reduced by providing sufficient length of travel. This tank is designed such that the time taken by the water particle to travel from one end to another end is kept slightly more than the time required for settling of suspended particles in water. 2) Intermittent Tank: In this tank, water is completely brought to rest. This type of tank works intermittently.

SEDIMENTATION BASIN ZONES 1) Inlet Zone: The inlet or influent zone should distribute flow uniformly across the inlet to the tank. The normal design includes baffles that gently spread the flow across the total inlet of the tank and prevent short circuiting in the tank. 2) Settling Zone: The settling zone is the largest portion of the sedimentation basin. This zone provides the calm area necessary for the suspended particles to settle. 3) Sludge Zone: The sludge zone, located at the bottom of the tank, provides a storage area for the sludge before it is removed for additional treatment or disposal. Sludge is removed for further treatment from the sludge zone by scraper or vacuum devices which move along the bottom. 4) Outlet Zone : The basin outlet zone (or launder) should provide a smooth transition from the sedimentation zone to the outlet from the tank. This area of the tank also controls the depth of water in the basin.

Circular Basin Rectangular Basin

Critical Settling Velocity and Overflow Rate Critical settling velocity (Vo)is the settling velocity of particles which are 100% removed in the basin

Typical Dimensions of Sedimentation Tanks Description Dimensions Range Typical Rectangular Depth, m 3-5 3.5 Length, m 15-90 25-40 Width, m 3-24 6-10 Circular Diameter, m 4-60 12-45 Depth, m 3-5 4.5 Bottom Slope, mm/m 60-160 80

15 SEDIMENTATION Discrete Particles Flocculating Size Shape weight Suspension Dilute Concentrated

16 Types of Settling:- Depending upon the concentration of solids and the tendency of a particle to interact the following types of settling may occur Type I: Discrete Settling: This corresponds to the sedimentation of discrete particle in a suspension of low solids concentration. No interaction between particles Settling velocity is constant for individual particles Type II: Hindered Settling: This type of settling refers to dilute suspension of particles that flocculate during sedimentation process.

Type III: Zone of Settling: Refers to flocculent suspension of Intermediate solids concentration Solids move as a block rather than individual particles Mass of particles subside as whole Type IV: Compression settling Flocculent suspension of high concentration. Volume of solids may decrease

Inlet & Outlet Arrangement for Sedimentation Tank

Design Concept of Sedimentation: 1) Flow Velocity, v H = (Q/(B x H)) 2) Over Flow Rate = Surface Loading, v O = (Q/(B x L)) 3) Settling Velocity, v s :- (v H / v S ) = (L / H) Particles with settling velocity v S equal to or greater than v O will settle down. 4)Over flow rate = 500 to 750 lit/hr/m2 ( Plain Sedimentation) 5) Over flow rate = 1000 to 1250 lit/hr/m2 ( Sedimentation with coagulation) 6) Length of Tank, L greater than or equal to 4B (Width of tank, B should not exceed 12 m) 7) Flow velocity = 0.15 to 0.9 m/min. 8) Length of Tank = L = v H x D T (Detention Time = 4 to 8 Hrs) 9) Depth of Tank = 3 to 4.5 m 10)Provision for Sludge = 0.3 to 1.2 m & FB = 0.3 to 0.5m

Design Concept of Sedimentation: 1) Stokes Law :- Vs = ((g/18)(gs-1)(d 2 / u)) g = acceleration due to gravity Vs = settling velocity D = diameter of particle, cm Gs = specific gravity u = kinematic viscosity = 0.01 cm 2 /s Find the settling velocity of a particle in water for following condition: Diameter of particle = 0.06 mm, specific gravity of particle = 2.65, temperature of water = 20 0 c, Kinematic Viscosity of water at 20 0 c = 1.007 centistokes. G = 9.81 m/s 2 = 9810 mm/s 2, u = 1.007 centistokes = 1.007mm 2 / s

sedimentation A circular sedimentation tank is generally provided with its bottom cone shaped with a slope of 1 vertical to 12 horizontal. Under this condition, its diameter is given by: V = D 2 (0.011 D + 0.785 H)

Design a plain sedimentation tank for max. daily demand of water 9.5 x 10 6 lit / day. Assume the velocity of flow to be 20 cm / minute and detention time 8 hours. Ans: Quantity of water to be treated = 9.5 x 10 6 lit / day = 395833.33 lit / Hr Capacity of Sedimentation tank required = V = Q x D T = 395833.33 x 8 = 3.17 x 10 6 Lit = 3170 m3 Velocity of flow to be maintained through the tank, v = 20 cm / min = 0.2 m / min. The length of tank required, L = v x D T = 0.2 x 8 x 60 = 96 m The c/s area of the tank is required = ( Capacity of tank / Length of Tank ) = 3170 / 96 = 33 m2 Assuming the water depth in the tank is 4 m. The width of tank, B = C/s area / Depth = 33/4 = 8.25 m (< 12m)

Design a plain sedimentation tank for a population of 100000 with water supply rate 135 lpcd. Ans: Quantity of water to be treated = 100000 x 135 x 1.8 = 1012.5 m3/ hr Assuming Detention Time = 6 Hours Capacity of Sedimentation tank required = V = Q x D T = 1012.5 x 6 = 6075 m3 Assuming Velocity of flow through the tank, v = 0.6 m / min. The length of tank required, L = v x D T = 0.6 x 6 x 60 = 216 m The c/s area of the tank is required = ( Capacity of tank / Length of Tank ) = 6025 / 216 = 28.125 m2 Assuming the water depth in the tank is 4 m. The width of tank, B = C/s area / Depth = 28.125/4 = 7.03 m (< 12m) FB = 0.5m Depth for sludge = 1m Overall Depth of Tank = 4 + 1 + 0.5 = 5.5 m Dimension of Tank = 216 x 7.02 x 5.5m

Filtration 1) Process of removal of impurities like very fine suspended particles, bacteria, color, taste, etc. by passing the water thorough bed of granular materials. 2) Types of filter: 1) SSF 2) RSF 3) Pressure Filter

Mechanism involved in Filtration 1) Mechanical straining 2) Sedimentation 3) Adsorption 4) Biological metabolism 5) Electrolytic changes

Slow Sand Filter 1) Removes about 98 to 99 % of bacterial load 2) Removes turbidity. 3) Less efficient in removal of color about 20 to 25 % 4) Not highly efficient in the removal of colloidal matter.

Slow Sand Filter

Slow Sand Filter Construction:- Open basin rectangular in size Watertight shallow tank constructed in stone or brick masonry Depth of tank 2.5 to 4m Surface area 100 to 2000 sq. m Filtration rate 100 to 200 liters per hour per sq. m. Total depth of media 90 to 110 cm. Sand depth 60 to 90 cm and Gravel bed 30 to 60 cm Bed slope 1 in 100 to 1 in 200 towards central drain Finer sand better bacterial removal efficiency but slower filtration rate Effective size of sand (D10) 0.2 to 0.35 Uniformity coefficient (D60/D10) 2 to 3

Slow Sand Filter Operation:- 1) Waters should not be coagulated. 2) Filter is filled with a raw water to a depth of 1 to 1.5 m above the surface of sand. 3) Water is passed with filtration rate 100 to 200 liters/hr/ sq. m. 4) Loss of head 60 cm 5) For cleaning 20 to 30 cm top sand is scraped & replaced 6) First filter water is collected by under drainage system

Rapid Sand Filter

Rapid Sand Filter Construction:- 1) Open basin rectangular in size 2) Watertight shallow tank constructed in stone or brick or concrete masonry 3) Surface area 10 to 100 sq. m 4) Length to width ratio 1.25 to 1.35 5) Filtration rate 3000 to 6000 liters/hr/sq. m. 6) Depth of tank 2.5 to 3.5m 7) Total depth of media 90 to 130 cm. 8) Sand depth 60 to 70 cm & Gravel bed 60 to 70 cm 9) Effective size of sand (D10) 0.35 to 0.6 10) Uniformity coefficient (D60/D10) 1.2 to 1.7

Operation:- Rapid Sand Filter 1) Enters filter through inlet pipe 2) Uniformly distributed on the sand bed 3) After passing through bed collected by UDS 4) Initially head loss very small as increases beyond limit bed requires washing (30cm to 3m) Back washing:- 1) Back flow of water 2) First water drained out form filter 3) All valves are closed & compressed air is passed for 2-3 minutes 4) Water passes thorough drain, gravel & sand. 5) Sand expands and all impurities are carried away with water drain. 6) After 24 hr & requires 10 minutes

Design of slow sand filter 40000 Population & 200 lpcd max. water supply rate:- Water to be treated per day = max. daily demand x population = 200x40000 = 8000000 lit/day Assuming rate of filtration = 200 lit/hr/m 2 = 200x24 = 4800 lit/day/m 2 Total surface area of filter reqd = (water reqd to be treated per day / rate of filtration) = (8000000/ 4800) = 1667 m 2 Provide four units, out of four keep one stand by while repairing and hence only three units provide the necessary filter area reqd. The area of each filter unit = (1667/3) = 556 m 2 Assuming L= 2B Area of each filter unit = 556 = L x B = 2 B x B B = 16.7 m & L = 33.4 m

Assuming thickness of sand filter media = 0.9 m Assuming thickness of gravel filter media = 0.5 m Depth of water = 1.2 m Free board = 0.3 m Under drainage system = 0.6 m Overall Depth of Filter = 0.9 + 0.5 + 1.2 + 0.3 + 0.6 = 3.5 m Dimension of filter = 33.4 x 16.7 x 3.5 m

Rapid Sand Filter 1) Water reqd to treat per day in liter 2) Rate of filtration = 3000 to 6000 lit/hr/m 2 3) Total surface area of filter reqd 4) No. Of units 5) Area of each unit (10 to 100 m 2 ) 6) L=1.5 B 7) Thickness of sand bed = 60 to 70 cm 8) Thickness of gravel bed = 60 to 70 cm 9) Depth of water = 0.9 to 1.6m 10) FB = 0.5m 11) UDS = 0.6m

Pressure Filter

Pressure Filter 1) Vertical and horizontal 2) Similar to RSF 3) Filtration rate = 6000 to 15000 lit/hr/m2 4) Pressure = 3 to 7 kg/cm2 5) Few houses, private estate, industries, swimming pools, railway station, etc. 6) Least efficient in removal of bacteria & turbidity 7) Difficult to inspect, clean & replace 8) Effectiveness of backwashing is not visible. 9) Good quality of water

Pressure Filter

Filter troubles or Problems 1) Formation of Mud Balls 2) Clogging and Cracking of filter beds 3) Air binding 4) Sand Incrustation 5) Jetting & Sand Boils 6) Sand Leakage

Filters during backwash