ASTM E 1886 & 1996-05B DECEUNINCK NORTH AMERICA 142.094 SH 003 Single Hung Window REPORT #CCLI-11-160 August 18, 2011 TABLE OF CONTENTS 1. PROJECT DATA...1 2. SUMMARY...1 3. TEST SPECIMEN...1 4. IMPACT ACCEPTANCE CRITERIA...3 5. PERFORMANCE RESULTS...3 6. DISCLAIMER.....4 APPENDIX APPENDIX A: DECEUNINCK NORTH AMERICA 142.094 SH - 003 PVC SINGLE HUNG TILT WINDOW DRAWINGS Refer to Appendix A. This report is not complete unless these drawings are stamped and initialed by CCLI as illustrated below. DRAWING/DETAIL SHEET DATE STAMPED AS ILLUSTRATED BOM / Layout Main Frame 10008675_SH 06/03/99 Head Frame 10008676_SH 06/07/99 Sill Frame 10008672_SH 06/18/02 Lift Rail 10008882_SH 08/04/97 Lock Rail 10008895_SH 02/08/94 Meeting Rail 10008511_SH 08/27/03 Glazing Bead 10005470_SH 06/01/93 Bulb Seal 10008206_SH 06/12/97 Sash Reinforcement 10300082 08/24/06 Meeting Rail Reinforcement 10300084 04/21/05 Sill Reinforcement 10300096 08/14/06 S-UNITED, INC. A Quality Control Company

ASTM E 1886 & 1996-05B DECEUNINCK NORTH AMERICA 142.094 SH 003 Single Hung Window REPORT #CCLI-11-160 August 18, 2011 1. PROJECT DATA Page 1 of 5 Project: ASTM E 1886-1996 Date of Testing: June 8, 2011 Tested For: Deceuninck North America 351 North Garver Road Monroe, OH 45050 Witnessed By Deceuninck North America Construction Consulting Laboratory, International (All or Partial Viewing) Jonathan Morton Chevis Wilson 2. SUMMARY Series Product Type Test Size Positive DP Negative DP 142.094 SH - 003 Single Hung 3'-8" x 7'-0" 3120 Pa (65.0 Psf) 3120 Pa (65.0 Psf) 3. TEST SPECIMEN Product Type: PVC Single Hung Tilt Window, Product Drawings, Appendix A Series Model: Series 142.094 SH - 003 Single Hung Tilt Window Specification 1886-05 1996-05B Test Methods: 1996-05b Wind-Zone 4 ASTM E 1886-05 +/-3120Pa (+/-65.0 Psf) Frame Size: 1119 x 2134 (3'-8 1 /16" x 7'-0") (44.0625" x 84") Sash Size: 860 x 892 (3'-4 13 /16" x 2'-11 1 /8") (40.8125" x 35.125") Fixed DLO: 984 x 1130 (3'-2¾" x 3'-8½") (38.750" x 44.500") Sash DLO: 962 x 826 (3'-1 7 /8" x 2'-8½") (37.875" x 32.500") Configuration: O/X Weather-Stripping: Pile weather strip with plastic center fin 4.75mm x 7.36mm (0.187" x.290" backed) at the exterior face of sash top rail and stiles pile also located at the lateral face of sash stiles. Pile weather strip with plastic center fin 4.75mm x 7.36mm (0.187" x.290" backed) at the interior face of frame sill interior leg. Foam bulb (.375" x.300") located at sash bottom rail. S-UNITED, INC. A Quality Control Company

ASTM E 1886 & 1996-05B DECEUNINCK NORTH AMERICA 142.094 SH 003 Single Hung Window REPORT #CCLI-11-160 August 18, 2011 Page 2 of 5 Weep Arrangement: Screen track weeped by 9.53mm x 3.175mm (1" x 1 /8") slot spaced 39.69mm (1 9 /16") from each end. Sash glass pocket weeped with one (1) 9.53mm x 4.76mm ( 3 /8" x 3 /16") punched weep through both legs spaced 82.55mm (3¼") from each end. Fixed meeting rail weeped with one (1) 2.38mm ( 3 /32") weep hole punched through both legs spaced 82.55mm (3¼") from each end. Hardware: Metallic cam action locks 203.2mm (8") from each end of sash top rail, attached by two (2) #8 x 19.05mm (¾") PFH screws with keepers at fixed interlock attached with two (2) #8 x 12.7mm (½") PFH screws. Metallic spring loaded tilt latch at each end of sash top rail. Metallic pivot bar at each end of sash bottom rail attached with one (1) #8 x 9.52mm ( 3 /8") screw per bar. Metal snubbers located at the underside of bottom rail and frame sill 381mm (15") from each end, attached with #8 x 12.7mm (½"). Reinforcement: 6005-T5 aluminum extrusion part #10300082 located at sash stiles, lift rail and lock rail. 6005-T5 aluminum extrusion part #10300084 located at fixed meeting rail. Reinforcement part #10300096 located at frame sill. Impact Glass: Sealed insulating glass: One piece, 3.17mm ( 1 /8") DSB annealed glass at the exterior with 7.24mm (.285") airspace, two pieces 3.17mm ( 1 /8") DSB annealed glass with 2.286mm (.090") Solutia PVB laminate at interior, 19.05mm (¾") overall thickness. Glass insulated with warm edge air spacer. Glazing: Sash lite is exterior glazed with Sika 552 polyurethane back bedding compound at interior, full perimeter and rigid vinyl snap-in glazing bead at exterior of glass. Fixed lite is interior glazed with Sika 552 polyurethane back bedding compound at exterior, full perimeter and rigid vinyl snap-in glazing bead at interior of glass. Installation Features: Frame nail fin was attached to SPF, nominal 50.8mm x 101.6mm (2" x 4") test buck w/silicone and (2") 6d penny nails through fin spaced 152.4mm (6") from each end and approximately on 152.4mm (6") centers, full perimeter. Other Features: Frame and sash corners are mitered and welded. Frame sill also attached to frame jambs with one (1) #8 x 19.05 ( ¾") PPH per corner. Fixed interlock rail reinforcement attached to jambs with one (1) #8 x 76.2mm (3") truss head screw at each end. Fixed interlock rail anchor part #79543 w/gasket attached to jambs with #8 x 25.4mm (1") PFH. S-UNITED, INC. A Quality Control Company

ASTM E 1886 & 1996-05B DECEUNINCK NORTH AMERICA 142.094 SH 003 Single Hung Window REPORT #CCLI-11-160 August 18, 2011 Page 3 of 5 4. IMPACT ACCEPTANCE CRITERIA The test specimen shall resist the large missile impact with no tear formed longer than 5" (130mm) and wider than 1mm ( 1 /16") through which air can pass or no opening formed through which a 3" (76mm) diameter solid sphere can freely pass when evaluated upon completion of missile impacts and test loading program. 5. PERFORMANCE RESULTS Title of Test Test Method Measured Allowed 5.3.1.1 Operating Force Open 71N (16.0 lbs) 135N (30 lbs) Close 85N (19.0 lbs) 135N (30 lbs) 5.3.1.1.3 Latching Devices 22N (5.0 lbs) 100N (22.5 lbs) 5.3.4.3 Uniform Load Structural ASTM E 330-02 4680 Pa (97.5 psf) Positive Deflection 19.05mm (.75") No Damage 4680 Pa (97.5psf) Negative Deflection 15.24mm (.60") No Damage -Permanent Set.76mm (.03") 5.91mm (0.233") Specification: ASTM E 1996-05b Missile Level Type D (#2 yellow pine weighing 9 lbs 2 ozs and measured 8'-3" overall). Test Specimen 1 ASTM E 1996-05b Par No Speed Rotation Title of Test Measured Allowable 5.3.1.1 50.1 fps 0º Center of Sash Glass No Penetration No Penetration 5.3.2.1 50.3 fps 0º Upper Right Corner No Penetration No Penetration Test Specimen 2 Par No Speed Rotation Title of Test Measured Allowable 5.3.1.2 51.3 fps 0º Lower Left Corner No Penetration No Penetration 5.3.2.2 50.2 fps 0º Center of Sash Glass No Penetration No Penetration Test Specimen 3 Par No Speed Rotation Title of Test Measured Allowable 5.3.1.3 51.0 fps 0º Upper Right Corner No Penetration No Penetration 5.3.3.6 50.7 fps 0º Center of Interlock No Penetration No Penetration S-UNITED, INC. A Quality Control Company

ASTM E 1886 & 1996-05B DECEUNINCK NORTH AMERICA 142.094 SH 003 Single Hung Window REPORT #CCLI-11-160 August 18, 2011 Page 4 of 5 Test Specimen 1 Test Specimen 2 Test Specimen 3 - Indicates 2 nd impact to specimen. The laboratory temperature was recorded at 85ºF for the duration of testing. Test specimens were stored in the lab prior to testing and the skin temperature of the vinyl was recorded at 85ºF. Visual inspections performed on the test specimens revealed there were no penetrations through the laminate and no separation of vision-to-frame glazing at the conclusion of the large missile impact tests. Specification: ASTM E 1886-05 Load 3120 Pa 65 PSF Positive Load 3120 Pa 65 PSF Negative Sequence Range Cycle Time Cycles Average Deflection Cycle 1 0.2 P to 0.5 P < 3 seconds 3500 9.40mm (.37") Cycle 2 0 to 0.6 P < 3 seconds 300 9.90mm (.39") Cycle 3 0.5 P to 0.8 P < 3 seconds 600 13.71mm (.54") Cycle 4 0.3 P to 1.0 P < 3 seconds 100 17.78mm (.70") Sequence Range Cycle Time Cycles Average Deflection Cycle 1 0.3 P to 1.0 P < 3 seconds 50 14.73mm (.58") Cycle 2 0.5 to 0.8 P < 3 seconds 1050 12.19mm (.48") Cycle 3 0 to 0.6 P < 3 seconds 50 7.87mm (.31") Cycle 4 0.2 P to 0.5 P < 3 seconds 3350 6.85mm (.27") Visual inspections performed on the test specimens revealed there were no penetrations through the laminate and no separation of vision-to-frame glazing at the conclusion of the cyclic pressure differentials. S-UNITED, INC. A Quality Control Company

ASTM E 1886 & 1996-05B DECEUNINCK NORTH AMERICA 142.094 SH 003 Single Hung Window REPORT #CCLI-11-160 August 18, 2011 Page 5 of 5 Detailed extrusion and assembly drawings indicating measured wall thickness and corner construction are on file and were compared to the test sample submitted. These records will be retained at CCLI for a period of four years. 6. DISCLAIMER The above results were obtained by using the designated test methods and indicate compliance with the above specification. This report does not constitute certification of this product, which may only be granted by the program administrator. CONSTRUCTION CONSULTING LABORATORY, INTERNATIONAL JEFFREY CRUMP TESTING MANAGER WESLEY WILSON LABORATORY MANAGER S-UNITED, INC. A Quality Control Company

ASTM E 1886 & 1996-05B DECEUNINCK NORTH AMERICA 142.094 SH 003 Single Hung Window REPORT #CCLI-11-160 August 18, 2011 APPENDIX A PROJECT DRAWINGS DRAWING/DETAIL SHEET DATE BOM / Layout Main Frame 10008675_SH 06/03/99 Head Frame 10008676_SH 06/07/99 Sill Frame 10008672_SH 06/18/02 Lift Rail 10008882_SH 08/04/97 Lock Rail 10008895_SH 02/08/94 Meeting Rail 10008511_SH 08/27/03 Glazing Bead 10005470_SH 06/01/93 Bulb Seal 10008206_SH 06/12/97 Sash Reinforcement 10300082 08/24/06 Meeting Rail Reinforcement 10300084 04/21/05 Sill Reinforcement 10300096 08/14/06 - END OF REPORT - S-UNITED, INC. A Quality Control Company