Nazdar offers a variety of adhesion promoters that can help with difficult to adhere to substrates. The table included at the beginning of this document is a guide for selecting the correct product for your application. Please refer to our technical data sheets for the primary substrates for each ink as in many cases a primer is not needed at all. Substrate Nazdar 7020 Nazdar 7025 Nazdar 7030 Nazdar 7035 Styrene NA NA Coated Alumapanel NA NA NA Fluted Polypropylene NA NA Acrylic NA Lexan NA Glass NA NA Rigid PE NA NA NA Nazdar 7020 Adhesion Promoter LWU7020NC Adhesion Promotion has been specially formulated as a primer to improve adhesion of Nazdar UV curable digital inks to substrates such as polypropylene and acrylic. This product is for use by customers requiring die and router cut chip resistance or improved tape pull resistance. Primary Features & Page 1 of 5 Acrylics Fluted/corrugated polypropylene with a surface tension at or above 44 dynes/cm & Usage LWU7020NC Primer was designed to be used as a wipe on primer. Shake container to mix contents prior to application. Dip a clean, lint free, dry towel into a container of LWU7020NC and wipe onto the substrate to be printed. Cover the entire substrate with primer making sure to get a uniform deposit across the substrate.. UV curable inks should be printed onto the thoroughly dried primer. Store ink and flush solutions at 18-32 C (65-90 F). Ink and flush solutions should always be kept away from heat, sparks, and flames. If stored at a different temperature, the ink should be allowed to reach room temperature before calibration or printing. The shelf life of this product is 6 months from the date of manufacture when stored under prescribed conditions.
Nazdar 7025 Glass Primer LWU7025 UV Glass Primer has been specially formulated as a wipe-on primer to improve adhesion of Nazdar UV curable digital inks to glass and enamel coated aluminum composite panels (Dibond). Primary Features & Page 2 of 5 Glass Dibond (and other composite enameled aluminum panels) & Usage LWU7025 Glass Primer was designed to be used as a wipe on primer. Apply some LWU7025 to a lint free, dry cloth and wipe onto the substrate to be printed. Cover the entire substrate with primer making sure to get a very thin, uniform deposit across the substrate. Apply to the non-tin side of float glass. Adhesion can be further improved by baking the newly primed glass surface for 10 minutes at 110 C (230 F). and flames. The shelf life of this product is 12 stored under prescribed conditions. If the primer has been exposed to excessive heat and has become cloudy in the bottle, discontinue use and replace the primer with fresh product. Operational: 30% - 70% (noncondensing)
Nazdar 7030 Adhesion Promoter LWU7030 UV Adhesion Promoter has been specially formulated as a wipe-on primer to improve adhesion of Nazdar UV curable digital inks on difficult-to-adhere-to point of purchase substrates. Primary Features & Page 3 of 5 Low Grade Styrene Acrylic Lexan & Usage LWU7030 UV Adhesion Promoter was designed to be used as a wipe on primer. Apply some LWU7030 to a lint free, dry cloth and wipe onto the substrate to be printed. Cover the entire substrate with primer making sure to get a very thin, uniform deposit across the substrate. and flames. The shelf life of this product is 15 stored under prescribed conditions. Operational: 30% - 70% (non-condensing)
Nazdar 7035 Adhesion Promoter LWU7035 UV Adhesion Promoter has been specially formulated as a wipe-on primer to improve adhesion of Nazdar UV curable digital inks on rigid polyethylene. Primary Features & Page 4 of 5 Rigid Polyethylene & Usage LWU7035 UV Adhesion Promoter was designed to be used as a wipe on primer. Apply some LWU7035 to a lint free, dry cloth and wipe onto the substrate to be printed. Cover the entire substrate with primer making sure to get a very thin, uniform deposit across the substrate. (Approx. 5 minutes depending on and flames. The shelf life of this product is 15 stored under prescribed conditions. Operational: 30% - 70% (non-condensing)
General Information Adhesion Promoter Handling All personnel mixing and handling these products must wear gloves and eye protection. Clean up all spills immediately. If the product does come in contact with skin, wipe off with a clean, dry cloth (do not use solvent or flush solution). Wash the affected area with soap and water. Nazdar Quality Statement Nazdar stands behind the quality of this product. Nazdar cannot, however, guarantee the finished results because Nazdar exercises no control over individual operating and production procedures. While technical information and advice on the use of this product is provided in good faith, the user bears sole responsibility for selecting the appropriate product for their end use requirements. Users are also responsible for testing to determine that our product will perform as expected during the printed item s entire life cycle from printing, post print processing, and shipment to end use. This product has been specially formulated for digital printing, and it has not been tested by any other method. Any liability associated with the use of this product is limited to the value of the product purchased from Nazdar. Based on information from our raw material suppliers, these products are formulated to contain less than 0.06% lead. If exact heavy metal content is required, independent lab analysis is recommended. Page 5 of 5 Manufacturers Product Offering Adhesion promoters are available in 1-liter containers. Nazdar Ink Technologies Offices Worldwide Nazdar Ink Technologies -World Headquarters 8501 Hedge Lane Terrace Shawnee, KS 66227-3290 USA Toll Free US: 866-340-3579 Tel: +1 913-422-1888 Fax: +1 913-422-2296 E-mail: custserv@nazdar.com Technical Support E-mail: InkAnswers@Nazdar.com Nazdar Limited EMEA Battersea Road, Heaton Mersey Stockport, England SK4 3EE Tel: + 44 (0)-161-442-2111 Fax: + 44 (0)-161-442-2001 EMEA Technical Service E-mail: technicalservicesuk@nazdar.com Nazdar Asia Pacific 11, Changi North Street 1 #03-03/04 Singapore 498823 Tel: +65-6385 4611 E-mail: aspac@nazdar.com