Pressure Booster System Hya-Eco VP Type Series Booklet
Legal information/copyright Type Series Booklet Hya-Eco VP KSB Aktiengesellschaft Frankenthal All rights reserved. Contents provided herein must neither be distributed, copied, reproduced, edited or processed for any other purpose, nor otherwise transmitted, published or made available to a third party without KSB s express written consent. Subject to technical modification without prior notice. KSB Aktiengesellschaft Frankenthal
Building Services: Water Supply Hya-Eco VP Designation Examp le: Hya- E co VP 2 / 46 / B Key to the designation Code Description Hya-Eco VP Type series 2 Number of pumps 4 Movitec pump size 6 Number of stages Inlet pressure [bar] B Design status Main applications Pressure boosting Fluids handled Pump for handling clean fluids not chemically and mechanically aggressive to the pump materials. Drinking water Service water Cooling water Operating data Overview of operating data Characteristic Value Flow rate Q Up to 7 m 3 /h (19.5 l/s with 3 pumps max.) 1) ) Head H Up to 11 m Fluid temperature t Up to 7 Up to 25 C to DIN 1988 (DVGW) Operating pressure p = Up to 16 bar Inlet pressure p in Up to 6 bar Design details Fully automatic pressure booster package system Long-coupled design Either two or three vertical high-pressure centrifugal pumps, type Movitec, with oval flange One check valve and shut-off valves to DIN/DVGW for each pump Anti-vibration pads per pump Membrane-type accumulator (direct-flow) to DIN 487-5 on the discharge side, approved for drinking water Pressure transmitter on the discharge side Pressure gauge for pressure indication Two standard volt-free changeover contacts for fault indication Design and function as per DIN 1988, Part 5 Ins tallation type Drive Stationary installation Electric motor 6 Hz, 2-pole, IE2, special KSB model, for three-phase mains Automat ion Control cabinet IP 54 Graphical display with operating panel LEDs indicating operational availability and fault of the system Service interface for connection to a PC Frequency inverter Transformer for control voltage Motor protection switch per pump Lockable master switch (repair switch) Pressure transmitter on the discharge side Wiring plan to VDE and parts list for electric parts Terminal strip/terminals with identification for all connections Terminal connection for digital dry running protection Remote ON connection Remote OFF connection 1) With stand-by pump as peak load pump Hya-Eco VP 3
Building Services: Water Supply Configuration and function Materials Overview of available materials 1 2 3 4 5 Hya-Eco VP 1 3 5 Control unit Pump Baseplate 2 4 Control cabinet Collecting line Design Fully automatic pressure booster package system, with 2 to 3 vertical high-pressure pumps and continuously variable speed adjustment of each pump for fully electronic control of the required supply pressure, with two standard volt-free changeover contacts for fault indication. Function Automatic mode Either two or three pumps (3) are controlled and monitored by a micro-processor control unit (1). Each pump is connected to a frequency inverter and controlled by the control unit so as to ensure a constant discharge pressure of the pressure booster system. As the demand increases or decreases, peak load pumps are started and stopped automatically. As soon as the demand increases again after one pump has been stopped, another pump which has not been in operation before is started up. When the last pump has been stopped and the demand increases again, the next pump in line is started up in variable-speed operation. The stand-by pump is also included in the alternating cycle. The standard setting is for the pressure booster system to start automatically as a function of pressure; the actual pressure is measured by an analog pressure measuring device (pressure transmitter). The function of this pressure transmitter is monitored (live-zero). As long as the pressure booster system is in operation, the pumps are started and stopped as a function of demand (standard setting). In this way it is ensured that the individual pumps operate only in line with the actual demand. The use of speed-controlled pumps reduces wear as well as the pumps' frequency of starts in parallel operation. If a duty pump fails, the next pump is started up immediately and a fault is output, which can be reported via volt-free contacts (e.g. to the control station). If the demand drops towards, the pressure booster system slowly runs down to the stop point. The operating status is displayed via LEDs. Function Manual mode In exceptional cases, the system can also be operated in manual mode. 4 Hya-Eco VP Component Inlet casing Discharge casing Hydraulic system Mechanical seal Primary ring Mating ring Elastomer Baseplate Hydraulics Distributor pipe Valves Membrane-type accumulator Membrane Material Stainless steel Stainless steel Stainless steel Complies with EN 12756 Silicon carbide Hard carbon EPDM Steel, powder-coated Stainless steel Copper base alloy/brass DVGW-approved Connection made of stainless steel, flow through valve to DIN 487-5 Approved for drinking water Product benefits Ready to connect due to standardised dimensions Constant pressure ensured by variable-speed pumps Corrosion-resistant due to internal stainless steel components Leakage monitoring and redundant system design (standby pump) ensure operating reliability
Selection information Requirements: Flow rate 4 m 3 /h Start-up pressure 4.5 bar Requested stand-by pump to DIN 1988 Solution: Hya Eco-VP 2/25 B 1. According to the table Flow rate as a function of the number of pumps the system may comprise 1 or 2 duty pumps (as stand-by pump is requested) 2. According to the table Flow rate as a function of the number of pumps the flow rate requirement can be either 4 m 3 /h (1 duty pump) or 2 m 3 /h (2 duty pumps) 3. The characteristic curves accordingly suggest Hya-Eco VP 2/25 (operating point close to Q opt ) 5 [US.gpm] 1 15 2 [IM.gpm] 4 6 8 1 12 18 Q min. 2/9--1,1 kw 1 35 9 2/8--1,1 kw 3 8 2/7--1,1 kw 25 7 2/6--,75 kw 6 2/5--,75 kw 2 H 5 45 4 2/4--,55 kw 2/3--,37 kw 15 3 1 2/2--,37 kw 2 NPSH R 1 8.5 Q [m 3 /h] 1. 1.5 2. 2.5 3. 3.5 6 5 2 η [%].8.1 P.5 [hp] [kw].4.2.5 Q [m 3 /h] 1. 1.5 2. 2.5 3. 3.5.2 [l/s].4.6.8 The required flow rate is split according to the number of the duty pumps (not taking into account any stand-by pumps). Flow rate as a function of the number of pumps Duty pumps Stand-by pumps Flow rate as a function of the number of pumps 1 1 Required flow rate flow rate as per characteristic curve Q [m 3 /h] 2 Required flow rate / 2 flow rate as per characteristic curve Q [m 3 /h] 2 1 Required flow rate / 2 flow rate as per characteristic curve Q [m 3 /h] 3 Required flow rate / 3 flow rate as per characteristic curve Q [m 3 /h] Hya-Eco VP 5
Technical data Systems with 2 and 3 pumps Hya-Eco VP Per motor Rated power Rated current P 2 [kw] [A] [kva] Total rated power requirement Mat. No. [kg] 2/22 B,37,91 1,32 29132656 12 2/23 B,37,91 1,32 29132657 121 2/24 B,55 1,29 1,88 29132658 122 2/25 B,75 1,75 2,55 29132659 123 2/26 B,75 1,75 2,55 2913266 127 2/27 B 1,1 1,93 2,81 29132661 128 2/28 B 1,1 1,93 2,81 29132662 129 2/29 B 1,1 1,93 2,81 29132663 133 3/22 B,37,91 1,99 29132664 147 3/23 B,37,91 1,99 29132665 152,6 3/24 B,55 1,29 2,82 29132666 15 3/25 B,75 1,75 3,82 29132667 151 3/26 B,75 1,75 3,82 29132668 158 3/27 B 1,1 1,93 4,21 29132669 159 3/28 B 1,1 1,93 4,21 2913267 16 3/29 B 1,1 1,93 4,21 29132671 167 2/42 B,55 1,29 1,88 29132672 12 2/43 B,75 1,75 2,55 29132673 125 2/44 B 1,1 1,93 2,81 29132674 126 2/45 B 1,5 2,86 4,16 29132675 13 2/46 B 1,5 2,86 4,16 29132676 136 2/47 B 2,2 4,12 5,99 29132677 137 2/48 B 2,2 4,12 5,99 29132678 144 3/42 B,55 1,29 2,82 29132679 148 3/43 B,75 1,75 3,82 2913268 154 3/44 B 1,1 1,93 4,21 29132681 156 3/45 B 1,5 2,86 6,24 29132682 162 3/46 B 1,5 2,86 6,24 29132683 171 3/47 B 2,2 4,12 8,99 29132684 172 3/48 B 2,2 4,12 8,99 29132685 183 Hya-Eco VP Per motor Rated power Rated current P 2 [kw] [A] [kva] Total rated power requirement Mat. No. [kg] 2/62 B,75 1,75 2,55 29132686 122 2/63 B 1,1 1,93 2,81 29132687 131 2/64 B 1,5 2,86 4,16 29132688 136 2/65 B 2,2 4,12 5,99 29132689 137 2/66 B 2,2 4,12 5,99 2913269 146 2/67 B 3, 5,55 8,7 29132691 147 3/62 B,75 1,75 3,82 29132692 15 3/63 B 1,1 1,93 4,21 29132693 162 3/64 B 1,5 2,86 6,24 29132694 171 3/65 B 2,2 4,12 8,99 29132695 172 3/66 B 2,2 4,12 8,99 29132696 184 3/67 B 3, 5,55 12,11 29132697 186 2/12 B 1,5 2,86 4,16 29133769 167 2/13 B 2,2 4,12 5,99 2913377 175 2/14 B 3, 5,55 8,7 29133771 193 2/15 B 3, 5,55 8,7 29133772 195 2/16 B 4, 7,3 1,62 29133773 27 3/12 B 1,5 2,86 6,24 29133775 218 3/13 B 2,2 4,12 8,99 29133776 23 3/14 B 3, 5,55 12,11 29133777 256 3/15 B 3, 5,55 12,11 29133778 259 3/16 B 4, 7,3 15,93 29133779 277 2/152 B 3, 5,55 8,7 29133781 213 2/153 B 5,5 1,29 14,97 29133782 31 2/154 B 7,5 13,23 19,25 29133783 32 2/155 B 7,5 13,23 19,25 29133784 322 3/152 B 3, 5,55 12,11 29133786 281 3/153 B 5,5 1,29 22,46 29133787 422 3/154 B 7,5 13,23 28,87 29133788 437 3/155 B 7,5 13,23 28,87 29133789 44 6 Hya-Eco VP
Type of connection Types of connection (schematic) Direct Indirect Unpressurised inlet tank at the same or at a higher level Unpressurised inlet tank at a lower level (suction-lift operation) 2) Inlet pressure monitoring (see Supplementary equipment or Accessories) At p in >.5 bar (min. 1 bar, DIN 1988) - Float switch - Pressure switch - Set of electrodes and relay - Pressure sensor - Dry running protection for PE inlet tank At p in <.5 bar - Pressure sensor - Pressure sensor - Flow monitoring 3) - Flow monitoring - Float switch - Set of electrodes and relay - Dry running protection for PE inlet tank - Flow monitoring 3) 2) Non-priming pumps, suitable for suction-lift operation (for selection, please consult KSB) 3) Automatic reset is not possible for this type of dry running protection Hya-Eco VP 7
Selection chart Shown for systems comprising 3 duty pumps 15 [US.gpm] 3 6 9 12 15 3 12 12 15 [IM.gpm] 3 6 9 12 15 3 1 3 2 5 4 2B 4B 6B 1B 15B 3 1 2 ft 5 4 1 H 3 2 5 3 Q [m 3 /h] 6 9 12 15 3 6 9.9 1.2 1.5 [l/s] 3 6 9 12 15 8 Hya-Eco VP
Characteristic curves Hya-Eco VP with Movitec 2B 5 [US.gpm] 1 2 [IM.gpm] 4 6 8 1 12 18 Q min. 1 2/9--1,1 kw 15 35 9 2/8--1,1 kw 3 8 2/7--1,1 kw 25 7 2/6--,75 kw 6 2/5--,75 kw 2 H 5 2/4--,55 kw 15 4 2/3--,37 kw 3 1 2/2--,37 kw 2 5 1 NPSH R.5 Q [m 3 /h] 1. 1.5 2. 2.5 3. 3.5 8 2 6 η [%].8.1 P.5 [hp] [kw].4.2.5 Q [m 3 /h] 1. 1.5 2. 2.5 3. 3.5.2 [l/s].4.6.8 Flow rate as a function of the number of pumps Duty pumps Stand-by pumps Flow rate as a function of the number of pumps 1 1 Required flow rate flow rate as per characteristic curve Q [m 3 /h] 2 Required flow rate: 2 flow rate as per characteristic curve Q [m 3 /h] 2 1 Required flow rate: 2 flow rate as per characteristic curve Q [m 3 /h] 3 Required flow rate: 3 flow rate as per characteristic curve Q [m 3 /h] Hya-Eco VP 9
Hya-Eco VP with Movitec 4B 1 [US.gpm] 2 5 [IM.gpm] 1 15 2 11 Q min. 4/8--2,2 kw 35 1 9 4/7--2,2 kw 3 8 m 4/6--1,5 kw 25 7 4/5--1,5 kw H 6 5 4/4--1,1 kw 2 15 4 4/3--,75 kw 3 4/2--,55 kw 1 2 5 NPSH R 1 1. Q [m 3 /h] 2. 3. 4. 5. 6. 7. 5 1 8 η [%] P.2 [kw].2 [hp]. 1 Q [m 3 /h] 2 3 4 5 6 7.5 [l/s] 1. 1.5 Flow rate as a function of the number of pumps Duty pumps Stand-by pumps Flow rate as a function of the number of pumps 1 1 Required flow rate flow rate as per characteristic curve Q [m 3 /h] 2 Required flow rate: 2 flow rate as per characteristic curve Q [m 3 /h] 2 1 Required flow rate: 2 flow rate as per characteristic curve Q [m 3 /h] 3 Required flow rate: 3 flow rate as per characteristic curve Q [m 3 /h] 1 Hya-Eco VP
Hya-Eco VP with Movitec 6B 1 [US.gpm] 2 3 4 [IM.gpm] 1 2 3 14 1 Q min. 6/7--3, kw 9 3 6/6--2,2 kw 8 25 7 6/5--2,2 kw H 6 5 6/4--1,5 kw 6/3--1,1 kw 2 15 4 3 6/2--,75 kw 1 2 5 12 2. Q [m 3 /h] 4. 6. 8. 1. NPSH R 4 8 1 η [%] P.2 [kw].3 [hp.. 2 Q [m 3 /h] 4 6 8 1.5 [l/s] 1. 1.5 2. 2.5 Flow rate as a function of the number of pumps Duty pumps Stand-by pumps Flow rate as a function of the number of pumps 1 1 Required flow rate flow rate as per characteristic curve Q [m 3 /h] 2 Required flow rate: 2 flow rate as per characteristic curve Q [m 3 /h] 2 1 Required flow rate: 2 flow rate as per characteristic curve Q [m 3 /h] 3 Required flow rate: 3 flow rate as per characteristic curve Q [m 3 /h] Hya-Eco VP 11
Hya-Eco VP with Movitec 1B 2 [US.gpm] 4 6 1 [IM.gpm] 2 3 4 5 12 4 11 35 1 1/6 -- 4, kw 9 3 H 8 7 6 1/5 -- 3, kw 1/4 -- 3, kw 25 2 5 4 3 1/3 -- 2,2 kw 1/2-- 1,5 kw 15 1 2 16 2 Q [m 3 /h] 4 6 8 1 12 14 NPSH R 2 1.4 8 7 5 η [%] P.7.5 [kw].2.1 2 Q [m 3 /h] 4 6 8 1 12 14 1 Q [l/s] 2 3.8 [hp] Flow rate as a function of the number of pumps Duty pumps Stand-by pumps Flow rate as a function of the number of pumps 1 1 Required flow rate flow rate as per characteristic curve Q [m 3 /h] 2 Required flow rate: 2 flow rate as per characteristic curve Q [m 3 /h] 2 1 Required flow rate: 2 flow rate as per characteristic curve Q [m 3 /h] 3 Required flow rate: 3 flow rate as per characteristic curve Q [m 3 /h] 12 Hya-Eco VP
Hya-Eco VP with Movitec 15B 2 4 [US.gpm] 6 8 1 2 [IM.gpm] 4 6 8 11 15/5 -- 7,5 kw 35 1 9 3 15/4 -- 7,5 kw 8 25 7 H 6 5 4 15/3 -- 5,5 kw 15/2 -- 3, kw 2 15 3 1 2 5 NPSH R 1 3 5 Q [m 3 /h] 1 15 2 24 3 2 1 8 η [%] P 1.5 [kw] 2 [hp] 5 Q [m 3 /h] 1 15 2 24 2 Q [l/s] 4 6 Flow rate as a function of the number of pumps Duty pumps Stand-by pumps Flow rate as a function of the number of pumps 1 1 Required flow rate flow rate as per characteristic curve Q [m 3 /h] 2 Required flow rate: 2 flow rate as per characteristic curve Q [m 3 /h] 2 1 Required flow rate: 2 flow rate as per characteristic curve Q [m 3 /h] 3 Required flow rate: 3 flow rate as per characteristic curve Q [m 3 /h] Hya-Eco VP 13
Dimensions Hya-Eco VP with Movitec 2B, 4B, 6B, 1B and 15B with 2 pumps Movitec 2B, 4B, 6B, 1B = R Movitec 15B = DN 126 H L B1 ±15 B ±15 Hya-Eco VP with Movitec 2B, 4B, 6B, 1B and 15B with 3 pumps Movitec 2B, 4B, 6B, 1B = R Movitec 15B = DN 126 H L B1 ±15 B ±15 14 Hya-Eco VP
Dimensions [mm] Number of pumps 2 3 Movitec B 874 874 2B/.. and 4B/.. 941 941 6B/.. 118 118 1B/.. 187 187 15B/.. B1 74 74 2B/.. and 4B/.. 88 88 6B/.. 885 885 1B/.. 884 884 15B/.. L 75 98 2B/.. and 4B/.. 75 98 6B/.. 75 98 1B/.. 98 121 15B/.. R R 2 R 2 2B/.. and 4B/.. R 2 R 2 6B/.. R 2 R 2 1B/.. DN DN 8 DN 8 15B/.. H 115 115 2B/.. and 4B/.. 115 115 6B/.. 145 145 1B/.. 145 145 15B/.. Scope of supply Depending on the model, the following items are included in the scope of supply: Pressure booster system Either two or three vertical high-pressure centrifugal pumps (standard pumps) Hydraulic components made of stainless steel One check valve and shut-off valves for each pump Membrane-type accumulator on the discharge side, approved for drinking water Pressure transmitter on the discharge side Pressure indication via pressure gauge Powder-coated steel baseplate Pumps mounted on the baseplate with anti-vibration mounts Control cabinet Control cabinet IP 54 Pump control and monitoring unit Graphical display with operating panel LEDs indicating operational availability and fault of the pressure booster system Service interface for connection to a PC Transformer for control voltage Motor protection switch per pump Lockable master switch (repair switch) Terminals with identification for all connections Circuit diagram, settings for frequency inverters and list of electrical components Connection for analog or digital dry running protection equipment External ON connection External OFF connection Accessories Supplementary equipment / options (E No.) supplied fitted to the pump set Accessories (Mat. No.) are included in the delivery but not fitted Dry running protection Dry running protection Part No. Description E No. Mat. No. [kg] 81-45 Dry running protection float switch 5 m 197165 1 With weight, PG cable gland and KTW approval 1 m 197395 5,5 Special lengths on request 2 m 1971651 1,8 81-45 Dry running protection float switch With KTW-approval Scope of supply: float switch with connection cable 81-45 Dry-running protection float switch 4) Scope of supply: Float switch with connection cable 59-11 Weight for adjusting the float switch level (weight with fastening elements) Dry running protection, electrodes set, with analysis 5) (When retrofitting it must be verified that sufficient space is provided in the control cabinet.) 5 m 113763 1,1 1 m 1137631 1,5 2 m 1137632 2 5 m 1137743,8 1 m 1137744 1,3 2 m 1137746 2,4 184615 1,2 169615,3 533947,3 4) Additional wiring to be effected by a trained electrician. 5) Not for Hya-Solo DV Hya-Eco VP 15
Part No. Description E No. Mat. No. [kg] E42 693 Dry running protection 4), (inlet pressure >,5 bar) For Hya-Eco K / VP via pressure switch Movitec 2, 4, 6, 1, 15 E4 184126 1,2 693 Dry running protection 4), (inlet pressure >,5 bar) For Hya-Eco VP via pressure transmitter Movitec 2, 4, 6, 1, 15 E41 184127 1,5 Adapters Adapters Part No. Description Mat. No. [kg] 82-5 Adapter 2½" Victaulic coupling DN 65 1136866,4 Pressure reducer Pressure reducer Part No. Size Type Honeywell Max. inlet Downstream Mat. No. [kg] pressure pressure 69-7 R 1 D6 F...A 25 bar 1,5-6 bar 157183 1,4 69-7 R 1 D6 FN...B 25 bar,5-2 bar 157184 2,4 69-7 R 1¼ D6 F...A 25 bar 1,5-6 bar 157185 2 69-7 R 1¼ D6 FN...B 25 bar,5-2 bar 157186 2,8 69-7 R 2 D6 F...A 25 bar 1,5-6 bar 522969 4,5 69-7 R 2 D6 FN...B 25 bar,5-2 bar 52296 5,6 69-7 DN 65 D15 16 bar 1,5-6 bar 522957 28,2 69-7 DN 65 D15N 16 bar,2-2 bar 522959 37 69-7 DN 8 D15 16 bar 1,5-6 bar 522958 41,5 69-7 DN 8 D15N 16 bar,2-2 bar 522956 54 69-7 DN 1 D15 16 bar 1,5-6 bar 119996 67 69-7 DN 1 D15N 16 bar,2-2 bar 119997 87,5 69-7 DN 15 D15 16 bar 1,5-6 bar 198244 15 69-7 DN 15 D15N 16 bar,2-2 bar 198247 196 69-7 DN 2 D15 16 bar 1,5-6 bar 198245 48 69-7 DN 2 Flanges drilled to PN 16, DIN 2533 D15N 16 bar,2-2 bar 198248 58 Expansion joints Expansion joints PN 1 Part No. Description Mat. No. [kg] 71-8 Expansion joints PN 1 R 1" 1137177,4 R 1¼" 1137178,2 R 1½" (not to 1137179,3 DVGW) 71-8 DN 4 with adapter flange PN 1/16 type 5 with KTW approval 112569 3,4 DN 65 with adapter flange PN 1/16 type 5 with KTW approval 1137184 5,6 DN 8 with adapter flange PN 1/16 type 5 with KTW approval 112572 6,7 Screwed flange R 1½ (internal thread) with screws, bolts and washers For expansion joint DN 4, type 49 Screwed flange R 2 (internal thread) with screws, bolts and washers For expansion joint DN 5, type 5 Screwed flange R 2½ (internal thread) with screws, bolts and washers For expansion joint DN 65, 49 Mat. 184968 5 Galvanised steel Mat. 1.4541 184969 5 Mat. 184647 5 Galvanised steel Mat. 1.4541 184646 5 Mat. 184649 6 Galvanised steel 16 Hya-Eco VP
Part No. Description Mat. No. [kg] Mat. 1.4541 184648 7 Screwed flange R 3 (internal thread) with screws, bolts and washers For expansion joint DN 8, type 49 Mat. 18497 7 Galvanised steel Mat. 1.4541 184971 7 Expansion joints PN 16 Type 49, blue, variant C: integrated length-limited expansion joints Drinking water-approved as per regulation of the German health authority (Bundesgesundheitsamt) of 1986 Part No. Size Material Mat. No. [kg] 71-8 DN 4 Rubber, St-TZN 112568 4,8 71-8 DN 5 Rubber, St-TZN 15746 8 71-8 DN 65 Rubber, St-TZN 15747 8 71-8 DN 8 Rubber, St-TZN 149847 5,5 71-8 DN 1 Rubber, St-TZN 149848 6,6 71-8 DN 15 Rubber, St-TZN 14985 11,4 71-8 DN 2 Rubber, St-TZN 1137185 1 Inlet tank with accessories Inlet tank Closed inlet tank under atmospheric pressure, made of polyethylene Part No. Total volume Effective volume Connection Connection Mat. No. [kg] [l] [l] Inlet line Outlet line 591.1 3 15 R 1 DN 5 1136287 3 591.1 6 3 R 1½ DN 5 1136288 4 591.1 75 5 R 1½ DN 5 1136289 5 591.1 15 8 2 x R 2 DN 8 113629 15 591.1 18 1 2 x R 2 DN 8 1136291 17 591.1 27 15 2 x R 2 DN 1 1136292 25 591.1 32 2 2 x R 2 DN 125 1136293 33 591.1 27 15 DN 8 DN 1 1136294 25 591.1 32 2 DN 1 DN 125 1136295 33 Membrane-type accumulator made of steel Part No. Description Type 6) 591 Membrane-type accumulator 7) Double connection PN 1 591 Membrane-type accumulator 7) Double connection PN 16 Effective Connection Mat. No. [kg] Nominal volume volume max. 8 l 6 DN 5 16495 33 2 l 15 DN 5 1651 56 3 l 225 DN 5 1652 61 5 l 35 DN 5 1653 91 6 l 34 DN 5 156394 258 8 l 45 DN 5 198687 27 1 l 45 DN 5 198688 345 11 l 75 DN 65 154867 42 8 l 6 DN 5 198689 7 2 l 15 DN 5 19869 116 3 l 225 DN 5 198691 11 4 l 3 DN 5 198692 18 6 l 34 DN 5 156395 298 8 l 45 DN 5 198693 27 1 l 45 DN 5 198694 345 11 l 75 DN 65 154868 345 6) Total volume in l 7) Adapter for DN 8 - DN 1: on request Hya-Eco VP 17
Part No. Description Type 6) Nominal volume Effective volume max. Connection Mat. No. [kg] Set of accessories DN 5 Blind flange for single connection 154865 1 Set of accessories DN 65 Blind flange for single connection 154866 1 Membrane rupture detector 114758 1 6) Total volume in l 18 Hya-Eco VP
KSB Aktiengesellschaft 67225 Frankenthal Johann-Klein-Str. 9 67227 Frankenthal (Germany) Tel. +49 6233 86- Fax +49 6233 86-341 www.ksb.com 1967.52/4-EN 4.5.212