Electronic Supplementary Material (ESI) for ChemComm. This journal is The Royal Society of Chemistry 2014 eocuproine-functionalized silica-coated magnetic nanoparticles for extraction of copper(ii) from aqueous solution Ashfaq Afsar, a Laurence M. Harwood,* a Michael J. Hudson, a Mark E. Hodson b and Elizabeth J. Shaw c a School of Chemistry, University of Reading, Whiteknights, Reading, Berkshire RG6 6AD, UK b Environment Department, University of York, Heslington, York, YO10 5DD c Department of Geography and Environmental Science, University of Reading, Whiteknights, Reading, Berkshire RG6 6AD Table of contents 1.0 Experimental Procedures S2 2.0 Extraction Results S13 S1
1.0 Experimental Procedures General procedure MR spectra were recorded using either a Bruker AMX400 or an Avance DFX400 instrument. Deuterated chloroform (CDCl 3 ) and Deuterated DMSO (dimethyl sulfoxide-d 6 ) were used as solvents. Chemical shifts ( values) were reported in parts per million (ppm) with the abbreviations s, d, t, q, qn, sx, dd, ddd and br denoting singlet, doublet, triplet, quartet, quintet, sextet, double doublets, doublet of doublets of doublets and broad resonances respectively. Coupling constants (J) are quoted in Hertz. IR spectra were recorded as ujol mulls () on a Perkin Elmer RX1 FT-IR instrument. All the melting points were determined on a Gallenkamp melting point apparatus. Mass spectra ( m / z ) were recorded under conditions of electrospray ionisation (ESI). The ions observed were quasimolecular ions created by the addition of a hydrogen ion denoted as [MH] +. The instrument used was Xcalibur Tune 2.1 (SP1). The structure of the precipitated powders was investigated by X-ray powder diffraction (XRD) with a Siemens D5000 diffractometer, using a monochromatized X-ray beam with nickelfiltered Cu Kα radiation. The size and morphology of the MPs at various stages of functionalization were observed by Philips/FEI CM20 transmission electron microscopy and samples were obtained by placing a drop of colloid solution onto a copper grid and allowing evaporating in air at room temperature. Volume statistics of particle sizes were determined by dynamic light scattering (DLS) (ZETA- SIZER, MALVER ano-zs). Thermo-gravimetric (TGA) analyses were performed using a TGA-Q50 thermo-gravimetric analyzer. S2
Iodoalkyl-functionalized silica coated magnetic nanoparticles (3) 2FeCl 3 FeCl 2 aoh H 2 O TEOS I Si O H 4 OH 3-IPTMS O O EtOH.H 2 O H 4 OH 1 2 EtOH.H 2 O n 3 Fe 2 O 3 Fe 32 O 43 Fe3 Fe2 O 43 Complete precipitation of Fe 2 O 3 was achieved under alkaline conditions, while maintaining a molar ratio of Fe 2+ :Fe 3+ = 1:2 under nitrogen. To obtain 0.7 g of γ-fe 2 O 3 MPs 1, FeCl 2.4H 2 O (0.8 g, 4 mmol) and FeCl 3 (1.3 g, 8 mmol) dissolved in degassed deionized water 40 ml were added dropwise into 2M aoh solution (200 ml) with vigorous stirring. After 1 hour, the resulting γ-fe 2 O 3 MPs 1 were separated by putting the vessel on a neodymium magnet and decaying the supernatant. The MPs 1 were washed with degassed deionized water (2 100 ml) and 0.01M HCl (17 %, 100 ml) to remove unreacted iron salts. γ-fe 2 O 3 MPs 1 were coated with SiO 2 using a sol-gel method. Typically, 0.7 g of γ-fe 2 O 3 MPs 1 were dispersed in a mixed solution of degassed ethanol (400 ml) and degassed deionized water (100 ml) by sonication for 10 min. H 4 OH (35 %, 36 ml) and tetraethyl orthosilicate (3.6 ml, 16 mmol) were consecutively added to reaction mixture and the reaction was allowed to proceed at room temperature for 2 h under continuous sonication. 3-iodopropyltrimethoxysilane (6.3 ml, 32 mmol) was then added and the reaction was allowed to proceed for further 3 h. The resultant functionalized particles 3 were obtained by magnetic separation and thoroughly washed with degassed ethanol (2 100mL). Finally the resultant yellow powder (2.3 g) was dried at 120 C. Preparation of 5-(4-hydroxyphenyl)-2,9-dimethyl-1,10-phenanthroline (6) OH HO Br 2 Br Fuming H 2 SO 4 B(OH) 2 4 5 Pd(PPh3)4, K2CO3 EtOH 6 93% 96% Fuming sulfuric acid (75 ml) was added to 2,9-dimethyl-1,10-phenanthroline 4 (5.11 g, 24.5 mmol). Bromine (0.76 ml, 14.7 mmol, 0.6 eq) was then added and the mixture was heated under reflux overnight. The flask was allowed to cool to room temperature and the solution was quenched with water (200 ml). aoh pellets were added until the ph of the solution was between 7-8. The resulting mixture was extracted with chloroform (2 200 ml) and the combined organic phases were dried over MgSO 4, filtered and the solvent removed under S3
vacuum to afford 5-bromo-2,9-dimethyl-1,10-phenanthroline 5 as a yellow solid (6.51 g, 93 %); Mp 175-178 C; 1 H-MR (400.1 MHz, CDCl 3 ): δ H (ppm) = 2.94 (s, 3H), 2.98 (s, 3H), 7.51 (d, J = 8.0 Hz, 1H), 7.59 (d, J = 8.0 Hz, 1H), 8.05 (s, 1H), 8.06 (d, J = 8.0 Hz, 1H), 8.54 (d, J = 8.0 Hz, 1H); 13 C MR (100.6 MHz, CDCl 3 ) δ C (ppm) = 25.7, 26.0, 119.7, 124.1, 124.3, 126.0, 127.1, 128.6, 135.4, 136.1, 144.8, 145.8, 160.0, 160.3; C 14 H 11 2 Br [MH] + requires m / z 287.0178; (FTMS + p ESI) MS found m / z 287.0180; IR v max / cm -1 = 3385, 3048, 2916, 2163, 1603, 1589, 1546, 1491, 1435, 1400. A suspension of 5-bromo-2,9-dimethyl-1,10-phenanthroline 5 (0.53 g, 1.8 mmol), tetrakis(triphenylphosphane)palladium(0) (0.07 g, 0.06 mmol, 0.03 eq), (4- hydroxyphenyl)boronic acid (0.28 g, 2.0 mmol, 1.1 eq) and K 2 CO 3 (0.29 g, 2.1 mmol, 1.3 eq) in degassed EtOH (75 ml) was heated to reflux for 18 h under nitrogen. The solution was allowed to cool to room temperature and filtered and the remaining solid residue was washed with EtOH (10 ml). The filtrate was evaporated and the solid was triturated with Et 2 O (25 ml). The insoluble solid was filtered and washed with chloroform (25 ml) and Et 2 O (25 ml) and allowed to dry in air to afford 6 as a yellow solid (0.53 g, 96 %); Mp (above 350 C); 1 H MR (400.1 MHz, DMSO-d 6 ) δ H (ppm) = 2.77 (s, 6H), 6.71 (d, J = 8.0 Hz, 2H), 7.13 (d, J = 8.0 Hz, 2H), 7.55 (d, J = 8.0 Hz, 1H), 7.57 (d, J = 8.0 Hz, 1H), 7.67 (s, 1H), 8.29 (d, J = 8.0 Hz, 1H), 8.34 (d, J = 8.0 Hz, 1H); 13 C MR (100.6 MHz, DMSO-d 6 ) δ C (ppm) = 24.8, 25.0, 117.0, 122.9, 123.5, 124.2, 125.8, 126.4, 130.7, 134.7, 136.1, 138.3, 143.6, 145.1, 157.3, 157.5, 164.1; C 20 H 17 2 O [MH] + requires m / z 301.1335; (FTMS + p ESI) MS found m / z 301.1335; IR v max / cm -1 = 3214 (O-H, phenol), 1608, 1591, 1490, 1373, 1277, 1238, 1165, 1144, 1102, 1010. Immobilisation of (6) on silica coated magnetic nanoparticles (7) HO I Si O O O Fe 32 O 43 ah DMF 6 n 3 7 n O Si O O O Fe 32 O 43 S4
Sodium hydride (60 % dispersion in mineral oil, 0.15 g, 3.8 mmol, 1.4 eq) was added to a solution of 5-(4-hydroxyphenyl)-2,9-dimethyl-1,10-phenanthroline 6 (0.83 g, 2.8 mmol) in DMF (100 ml) at 120 C and stirred for 30 min. Iodoalkyl-functionalized SiO 2 -coated MPs 3 (0.80 g) were slowly added and the reaction mixture was stirred at 120 C overnight. eocuproine functionalized MPs 7 were separated by an external magnet and were thoroughly washed with degassed ethanol (3 100mL). Finally, the product (0.6 g) was allowed to dry at 120 C. S5
1 H and 13 C MR spectra Br 8.55 8.53 1.00 1.02 8.07 8.05 8.05 0.36 0.39 7.60 7.58 7.52 7.50 7.26 0.33 0.68 2.98 2.94 4 10.0 9.5 9.0 8.5 8.0 7.5 7.0 6.5 6.0 5.5 5.0 f1 (ppm) 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 Br 160.25 159.95 145.81 144.76 136.08 135.35 128.62 127.07 126.03 124.28 124.13 119.69 26.02 25.74 4 200 190 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10 Figure S1. 1 H and 13 C MR spectra of 5-bromo-2,9-dimethyl-1,10-phenanthroline 5. S6
HO 8.36 8.33 8.30 8.28 1.01 0.50 1.06 1.01 1.00 7.67 7.58 7.56 7.55 7.54 2.99 7.16 7.14 6.72 6.70 2.77 5 10.0 9.5 9.0 8.5 8.0 7.5 7.0 6.5 6.0 5.5 5.0 f1 (ppm) 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 HO 164.14 157.51 157.34 145.09 143.61 138.26 136.09 134.67 130.65 126.36 125.80 124.16 123.49 122.89 116.99 24.97 24.77 5 200 190 180 170 160 150 140 130 120 110 100 f1 (ppm) 90 80 70 60 50 40 30 20 10 Figure S2. 1 H and 13 C MR spectra of 5-(4-hydroxyphenyl)-2,9-dimethyl-1,10- phenanthroline 6. S7
X-ray powder diffraction data d=2.513 d = 2.513 d = 2.946 Lin (Counts) d = 4.860 d = 4.036 d=2.946 d = 2.084 d=2.084 d = 1.698 d = 1.604 d=4.860 d=4.036 d=1.698 0 500 1000 1500 10 d=1.604 20 30 40 50 60 10 20 30 40 50 60 2-Theta - Scale 2-Theta-Scale Figure S3. X-ray powder diffraction pattern of γ-fe 2 O 3 MPs 1 overlapping the theoretical pattern for maghemite. Ps (2)(i) Lin (Counts) 1500 1000 Lin (Counts) 500 0 d = 3.891 d=3.891 d = 2.599 d=2.559 d = d=2.111 d = 1.485 d=1.485 5 10 20 30 40 50 60 2-Theta - Scale Ps (2)(i) - File: s04380wr.raw - Type: 2Th/Th locked - Start: 4.000 - End: 64.000 - Step: 0.050 - Step time: 32. s 19-0629 - Temp.: (*) 2 - Magnetite, syn - Fe3O4 - Y: 16.67 % - d x by: 1. - WL: 1.54056 25-1402 (I) - Maghemite-Q, syn - Fe2O3 - Y: 16.67 % - d x by: 1. - WL: 1.54056 38-0448 (Q) - Opal - SiO2 xh2o - Y: 12.50 % - d x by: 1. - WL: 1.54056 2-Theta-Scale Figure S4. X-ray powder diffraction pattern of SiO 2 -coated Fe 2 O 3 MPs 2. S8
Dynamic light scattering data Figure S5. Size distribution of γ-fe 2 O 3 MPs 1. Figure S6. Size distribution of iodoalkyl-functionalized SiO 2 -coated Fe 2 O 3 MPs 3. Figure S7. Size distribution of neocuproine-functionalized SiO 2 -coated MPs 7. S9
Thermal-gravimetric analysis S10
Figure S8. TGA curve of SiO 2 -coated Fe 2 O 3 MPs 2. Figure S9. TGA curve of iodoalkyl-functionalized SiO 2 -coated Fe 2 O 3 MPs 3. S11
15% Figure S10. TGA curve of neocuproine-functionalized SiO 2 -coated MPs 7. S12
2.0 Solvent Extraction Properties General Procedure Extraction of Cu(II) by neocuproine functionalized MPs 7 was investigated by means of the batch experiments at 25 C. A known amount of neocuproine functionalized MPs 7 was mixed with 10 ml of the corresponding Cu(II) solution over a period of time on a shaker at 200 rpm. After, the aqueous phase was extracted by magnetic decantation, the concentration of Cu(II) in the solution was determined by using an atomic absorption spectrometer (Perkin Elmer, 1100B). The extraction of Cu(II) by neocuproine functionalized MPs 7 was investigated at ph range of 2-8. The solution ph was adjusted by 0.1 M aoh or 0.1 M HO 3. The effects of the contact time (5-60 min) and the amount of MPs 7 dosage (3-15 mg) were also examined throughout the experiments at 25 C and 200 rpm shaking speed maintained. The amount of Cu(II) removal was calculated from the difference between Cu(II) taken and that remained in the solution. All extraction experiments were carried out in triplicate and error bars in figures represent standard deviations. 100 Romoval Efficiency (%) 80 60 40 20 0 2 3 4 5 6 7 8 Initial ph Figure S11. Effect of initial ph on the extraction efficiency of Cu(II) by MPs 7. S13
Removal Efficiency (%) 100 80 60 40 20 0 0 5 10 15 30 60 Time (minutes) Figure S12. Effect of contact time on extraction of Cu(II) by MPs 7. Romoval Efficiency (%) 100 80 60 40 20 0 3 4 5 6 7 8 9 12 15 Dosage (mg) Figure S13. Effect of MPs 7 dosage on extraction of Cu(II). S14