Premium Surfacer P565-5701, P565-5705 & P565-5707 H5620V Product Data Sheet July 2017 INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY Product Speed Surfacer P565-5801, P565-5805 & P565-5807 Description P565-5801 Speed Surfacer White SG 01 P565-5805 Speed Surfacer Grey SG05 P565-5807 Speed Surfacer Dark Grey SG07 2K HS Hardener - Fast P852-1678 Accelerator Thinner for Speed Surfacer P852-1690 Accelerator Thinner (For high temperature application) P850-1694 Slow Thinner for IR P850-1693 Medium Thinner for Roll Primer Mode Product Description Speed Surfacer combines process speed and ease of application with excellent sanding properties. Speed Surfacer is a primer that is incredibly fast and easy to apply, with excellent sanding properties. It has a quick and user-friendly one visit application (with little or no flash off), and air dries in less than an hour; improving bodyshop efficiency without compromising on the quality of the final finish. Speed Surfacer is available in three spectral grey shades (and can be mixed to provide further shades) in order to be able to provide the optimum spectral grey for every color. This further improves productivity and profitability by reducing basecoat consumption. Page 1 of 8
SUBSTRATES AND PREPARATION The P565-580X surfacers should only be applied over : Well sanded and degreased bare steel. Use Nexa Autocolor 2-pack Etch Primer or 2-pack Epoxy Primer for maximum durability. Aluminium must be Etch or Epoxy primed. Well sanded GRP, polyester fillers works primer and old finishes in sound condition. Good preparation is vital in order to obtain the best results from these products. The following grades of sanding paper are recommended for substrate preparation: - Wet or dry paper P280 - P320 (GRP P400) Dry machine sanding P180 - P240 NOTE: Not recommended for spot repairs over thermoplastic acrylic, old lacquer finishes or sensitive substrates. Over these substrates, apply to complete panels only. Page 2 of 8
Process PRIMER SURFACER P565-5801/5805/5807 7 parts 1 part P852-16XX / P850-1694 2 part NOTE: FOR ACCURATE ACTIVATION AND THINNING, WEIGHT MIXING IS RECOMMENDED (SEE PAGE 6). Activated viscosity: 27-32 secs DIN4 @ 20 C (7 : 1 : 2 activation) Pot-life: 45 min at 20 C Clean gun immediately after use Fluid Tip Gravity Fed: 1.6 mm Inlet Pressure: Refer to spraygun manufacturers recommendation (normally 2 bar / 30 psi). Fluid Tip Gravity Fed: Pressure: 1.6 mm Refer to spraygun manufacturers recommendation (0.7 bar / 10 psi max at air cap). 1 medium coat + 2 full coats to give a film thickness of 75-120 microns NB: Film build depends on thinner addition and fluid tip size. Between coats: 1 min after first coat. No flash off in 2-3 coat Before Force Drying: Until Matt (depending on spraying conditions) Page 3 of 8
Process Air-dry at 20 C: 1 hour Air-dry below 20 C: 1 hour Baking at a metal temperature of 60 C: 20 25 minutes depending on film thickness High Wave: 12 minutes P850-1694 to be used for IR drying process. Allow P565-580X surfacers to flash off for 5 minutes before drying with the infrared lamp. Drying times will depend on the type of infrared lamp used. Max 120 microns, when using force dry process. Finish with the following grades: - P360 or finer: Single layer solid colours (Direct Gloss) P400 or finer: Basecoats Finish with the following grades: - P600 or finer: Single layer solid colours (Direct Gloss) P800 or finer: Basecoats TOPCOAT P565-580X surfacers can be topcoated with Nexa Autocolor 2K topcoat systems. If P565-580X surfacers are left for more than 2 days after sanding, they should be sanded again prior to application of further undercoat or topcoat. Page 4 of 8
Process SPECTRAL GREYS For each of the Spectral Grey primer variants specified the following mixing ratio applies: Product number Mix % (by wt.) Mix by Target Weight 100g 250g 500g SG01 P565-5801 100 100g 250g 500g SG03 P565-5801 58 58g 145g 290g P565-5805 42 42g 105g 210g SG05 P565-5805 100 100g 250g 500g SG06 P565-5805 48 48g 145g 240g P565-5807 52 52g 105g 260g SG07 P565-5807 100 100g 250g 500g CHOICE OF HARDENER AND THINNER The choice of thinner should be made according to application temperature, air movement and size of job. The recommendations below are for guidance only :- Hardener: Thinner: Ideal temperature range: P852-1678 Below 25 C P852-1690 Over 30 C Page 5 of 8
Process Weight Activations for use with HS hardeners () Ratio 7 : 1 : 2 Please note the weights are cumulative. Do not tare or zero scale between additions P565-5801 P852-1678/90 P850-1694 1.0L 1019 1125 1297 P565-5805 P852-1678/90 P850-1694 1.0L 921 1027 1198 P565-5807 P852-1678/90 P850-1694 1.0L 929 1035 1207 Flexible Additive Weight Activations for use with HS hardeners () Please note the weights are cumulative. Do not tare or zero scale between additions P565-5801 P100-2020 P852-1678/90 P850-1694 1.0L 820 950 1059 1239 P565-5805 P100-2020 P852-1678/90 P850-1694 1.0L 741 871 980 1159 P565-5807 P100-2020 P852-1678/90 P850-1694 1.0L 748 877 986 1166 VOC INFORMATION The EU limit value for this product (product category: IIB.c) in ready to use form is max. 540g/litre of VOC. The VOC content of this product in ready to use form is max. 540g/litre. Depending on the chosen mode of use, the actual ready to use VOC of this product may be lower than that specified by the EU Directive code. Nexa Autocolor,, Aquabase, Aquadry and Ecofast are registered marks of PPG Industries Ohio, Inc. Copyright 2015 PPG Industries Ohio, Inc. All rights reserved. Copyright in the above product numbers that are original is asserted by PPG Industries Ohio, Inc.. Page 6 of 8
Roll Prime Process P565-5801/5805/5807 7 parts 1 part P850-1693 0.5 0.75 parts NOTE: It is recommended to use the material immediately after mixing. Clean roller tray immediately after use. Due to high viscosity and short potlife it is not recommended to use fast or accelerated thinners Pot-life: 30 min at 20 C RFU viscosity DIN4/20 C: 60-75 seconds (@ 7 : 1 : 0.5) 1. Use of good quality high density foam rollers is essential. Use of a suitable roller tray allows easy control of paint loading on the roller. 2. Load the roller from a suitable roller tray. Removed excess paint from the roller. 3. The first coat covers the largest area. Subsequent coats cover smaller areas. 4. Apply paint from the centre of the repair patch, rolling outwards using light pressure. 5. Use the roller with less paint loading to fade hard edges of each coat. 6. Allow the paint to flow out on the panel; avoid over- working, which can leave an uneven surface. 7. When one coat becomes matt, it is ready for the next coat. Usually it takes @ 3 minutes. 8. An application s process can be shorten using IR lamp to speed up the flash off times in between coats. 9. When IR lamp applied to flash off then it takes @ 1 minute. NOTE: The surface mast be cool down before next coat application. 10. RFU viscosity at 60 seconds gives the best balance in between application s properties, film build as well as the final appearance (orange peel) Number of coats: Flash off between coats: Flash off before force drying: 3-4 coats to give the film thickness of 100 150 μ Approx. 3 minutes (Flash off can be shorten to 1 minute using IR-lamp) Until matt Nexa Autocolor,, Aquabase, Aquadry and Ecofast are registered marks of PPG Industries Ohio, Inc. Copyright 2015 PPG Industries Ohio, Inc. All rights reserved. Copyright in the above product numbers that are original is asserted by PPG Industries Ohio, Inc.. Page 7 of 8
1 Litre RFU for Roll application (@ 7 : 1 : 0.5 ratio) SG 01 Weight Activations for use with HS hardener () Ratio 7 : 1 : 0.5 for roller application P565-5801 (7 Parts) Please note the weights are cumulative. Do not tare or zero scale between additions Wt Hardener (1 Part) Wt. Thinner P850-1693 (0.5 Parts) 1.0 L 1202 1327 1375 SG 05 P565-5805 (7 Parts) Wt Hardener (1 Part) Wt. Thinner P850-1693 (0.5 Parts) 1.0 L 1087 1211 1260 SG 07 P565-5807 (7 Parts) Wt Hardener (1 Part) Wt. Thinner P850-1693 (0.5 Parts) 1.0 L 1095 1220 1268 These products are for professional use only and are not to be used for purposes other than those specified. The information on this TDS is based on present scientific and technical knowledge, and it is the responsibility of the user to take all necessary steps in order to ensure the suitability of the product for the intended purpose. For Heath and Safety information please refer to the material Safety Data Sheet, also available at: www.nexaautocolor.com For further information please contact: Customer Service Sales Group PPG Industries (UK) Ltd Needham Road Stowmarket Suffolk IP14 2AD Tel: 01449 771771 Fax: 01449 773472 Nexa Autocolor,, Aquabase, Aquadry and Ecofast are registered marks of PPG Industries Ohio, Inc. Copyright 2015 PPG Industries Ohio, Inc. All rights reserved. Copyright in the above product numbers that are original is asserted by PPG Industries Ohio, Inc.. Page 8 of 8