Thermal Conductive Adhesive Sealant (RTV) PRODUCT DESCRIPTION TS-9001 Adhesive Sealant is a one-component, alcohol-released, and fast curing silicone which has excellent performance and good stability at room temperature (RTV-1) KEY FEATURES Light smell, and less volatile matter occurred during curing For sealing, little humidity is required for being fully cured Non-corrosive to meet metals, such as brass, aluminum, and steel. Meets MIL-A-46146B corrosion test Fast curing, suitable viscosity and flowability make it ideal for application where the electrical point of contact is of concern Excellent high and low temperature resistance: from -40 to 200 Flame retardant, UL94 V-0 (E231717) Nontoxic, meets the regulations of environmental protection, with SGS certification Excellent adhesion to a wide range of substrates. Primer is not required Fully cured adhesive sealant has excellent dielectric properties, meets UL certification. Excellent controlled volatility of siloxane Airtight, dustproof, shockproof, waterproof, insulating, and thermal conductive adhesive sealant for a wide range of applications, such as electrical, electronic, and mechanical applications TYPICAL PROPERTY DATA Uncured Properties Appearance Gray ; non-flowable Viscosity cps 150,000~200,000 Smell Slight alcoholic Tack-free Time (25 ) min <10 Gas Released During Curing Alcoholic gas Flowability mm 0~1-1 -
Cured Properties (7 days at room temperature) Hardness JIS A 65 Specific Gravity 1.62 Reduced Weight % 1 Coefficient of Thermal Expansion 2~3 x 10-4 Tensile Strength Kg/cm² >20 Elongation % 250 Volume Resistivity Ω cm >10 13 Dielectric Strength KV/mm >30 Flame Retardation 1mm/2mm UL-94 V-0 Thermal Conductivity W/m k >0.83 Volatile Siloxane (D3~D10) ppm <100 Temperature Resistance -40~200 Adhesive Aluminum Kg/cm² >20 Strength ABS Resin Kg/cm² >20 PCB Kg/cm² >20 CURING RATE (TEMPERATURE AND HUMIDITY) Curing Progress (mm) 10 9 8 7 6 5 4 3 2 1 0 15 /60% rh 25 /50% rh 25 /80% rh 40 /15% rh 40 /95% rh 1 2 3 4 5 6 7 10 9 8 7 6 5 4 3 2 1 0 Curing Time (1 Unit =1 Day) - 2 -
Time Curing (mm) 1 day 2 days 3 days 4 days 5 days 6 days 7 days 15 /60% rh 1.9 2.0 2.0 2.3 2.7 2.9 3.2 25 /50% rh 2.0 3.2 4.1 4.5 5.5 6.0 6.5 25 /80% rh 2.4 3.6 4.6 5.1 6.1 6.5 7.2 40 /15% rh 2.4 4.0 4.7 5.2 6.2 6.8 7.5 40 /95% rh 3.1 5.6 6.1 7.0 8.0 8.7 9.5 CURING TIME AND DIELECTRIC PROPERTIES Properties Initial 10 20 40 1 hr 2 hrs 10 hrs 24 hrs Stage min. min. min. Breakdown KV/mm 17 25 25 25 >30 >30 >30 >30 Voltage Volume Ω cm 9.5x10 10 2.6x10 11 8.1x10 11 1.1x10 12 3.1x10 12 8.1x10 12 8.4x10 13 8.8x10 13 Resistivity Curing condition: 25, 50% RH Thickness: Breakdown Voltage- 1mm; Volume Resistivity- 1.92mm CORROSION TEST The test is based on the method of MIL-A-46146B corrosion test. Test Procedure: 1. Pour 5 ml of distilled water and apply 15 grams of RTV into a glass bottle of 240c.c. 2. Hang a test plate of different materials in the glass bottle. 3. Maintain the bottle at 40 for 7 days. Test Result: Material Brass Aluminum Nickel Silver Steel 304 Result PASS PASS PASS PASS PASS - 3 -
ADHESION TO DIFFERENT MATERIALS Material Performance Material Performance Material Performance Brass Good ABS Good Steel 304 Good Aluminum Good Acrylic Good Epoxy Good Glass Good PVC Good Teflon Poor PC Good Cement Good Polyester Fair PCB Good Nickel Good PS Good PRO Good PET Good Polyimide Good Remark: Not suitable for applying to the humid surface. ELECTRICAL PROPERTIES IN DIFFERENT CONDITIONS OF AGING TEST High Temperature: 150 Properties 168 hrs 336 hrs 504hrs 672hrs Volume Resistivity 2.53x10 15 3.5x10 15 3.4x10 15 2.154x10 15 Breakdown Voltage >28 KV >28 KV >36 KV >40 KV High Humidity: 60, 90% rh Properties 168 hrs 336 hrs 504hrs 672hrs Volume Resistivity 8.3x10 13 8.0x10 13 5.95x10 13 2.87x10 13 Breakdown Voltage >29 KV >39 KV >33 KV >32 KV RELIABILITY Temperature Resistance at 150 : Properties 168 hrs 336 hrs 504hrs Tensile Strength Kg/cm² 20 20 18 Elongation % 200 180 180 Adhesive Strength to Aluminum Kg/cm² 20 18 18 Thermal Conductivity W/m k 0.87 0.91 0.91 Adhesive Strength at 60, 90% rh: aluminum vs aluminum Properties 168 hrs 336 hrs 504hrs Adhesive Strength Kg/cm² 18 18 15-4 -
HANDLING AND SAFETY Wear eye protection when handling uncured adhesive sealant as it can irritate eyes. In case of eye contact, immediately flush eyes well with water and contact a physician. Extended contact with the skin can cause irritation or harm and should be avoided. The alcoholic gas released during curing may be harmful. Adequate ventilation must be maintained in the work place at all times. High-pressure air is used as the tool of applying the adhesive sealant, and safety issue should be paid more attention. For industrial use only. For more details, please refer to the MSDS of TS-9001. STORAGE AND SHELF LIFE Store in a cool and dry place away from direct sunlight. Temperature should be below 35, and relative humidity should be below 80%. Keep out of the reach of children. Shelf life: 8 months from the date of manufacture. PACKAGING 330ml / cartridge 2600ml / cartridge / automatic applying - 5 -
ISSUED 2009/7/1 EDITION 9.0.1 FOR INDUSTRIAL USE ONLY The information contained herein is offered for information only and is believed to be reliable. The purchaser assumes all risk of use or handling of the product, whether in accordance with directions and information furnished herein or not, because conditions of use of our products is beyond TEMPO CHEMICALS CO., LTD s knowledge or control. It is the responsibility of the user to determine the suitability of our products for any intended application and to adopt such precautions as may be advisable for the protection of property and of persons against any hazards that may be involved in the handling and use thereof. In the light of the foregoing, the information contained herein is offered solely to assist the purchaser in selecting the appropriate products for the purchaser s own testing. TEMPO CHEMICALS CO., LTD specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of TEMPO CHEMICALS CO., LTD s products. TEMPO CHEMICALS CO., LTD, its sales agents, and its distributors specifically disclaim any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions shall not be taken as inducements to infringe any patent, as they are free from domination of patents owned by others or as a license under any TEMPO CHEMICALS CO., LTD patents that may cover such processes or compositions. We recommend that each user tests his proposed application before repetitive use, using this data as a guide. If any property, other than those in TEMPO CHEMICALS CO., LTD s specifications, is important to the purchaser, information as to such property will be supplied only upon the basis of test procedures agreed upon between TEMPO CHEMICALS CO., LTD and the purchaser prior to the acceptance of the purchaser order. A trademark of Tempo Chemicals Co., Ltd. TEMPO CHEMICALS CO., LTD. No. 453, Futhe 1 st Road, Hsichuh City, Taipei Hsien, Taiwan TEL: 886-2-8228-2278 FAX: 886-2-8228-6009 http://www.tempo-silicone.com.tw - 6 -