Nu-Render Tilt Slab & Off Form Concrete Finish

General Consent Document Nu-Render Tilt Slab & Off Form Concrete Finish March 2010 WATTYL (NZ) LTD

Paintworks Specification GS 425.1NZ Page 1 of 1 August 2005 System Substrate Category Grano Sponge Finish Satin Exterior New and uncoated off form concrete Premium Texture Water Based Product Features Grano Sponge Finish is a high performance pre blended modified cement based texturing material designed for use over Grano Adhesive Mortar (G1.06NZ) or Grano Modified Render (G1.10NZ). Grano Sponge Finish allows sponge, floated and various finishes to be achieved Surface Preparation Ensure all new cementitious substrates are fully cured prior to coating. Typically this may take a minimum of 4-6 weeks. There must be less than 15% moisture wood equivalent in the surface at the time of application to ensure optimum coating performance. The surface must not be subject to frequent wetting or hydrostatic pressure. Any foreign material that may affect adhesion must be removed prior to coating. Grind off any protruding formwork joints. Patching or Skimming Imperfections: Examine surfaces closely for air holes and imperfections, fill or skim as required with a GranoPatch Smooth (G1.04NZ), block down, allow to dry, sand back and dust off. Rendering: Render the new and uncoated brick & concrete blocks with the Grano Nu-Render or Nu-Solid rendering system for new and uncoated off form concrete. To access the Grano Nu-Render or Nu-Solid Installation Guides, contact Wattyl (NZ) Ltd for the regional Granosite Sales Consultant s contact details. Film Thickness Application Details Data Sheet Coverage (microns) Dry Times Wet Dry Touch Topcoat First Coat: Grano Sponge Finish (equipment: sponge, float, trowel to the desired effect) Second Coat: GranoPrime (equipment: roller or spray) Third & Fourth Coat: GranoImpact (equipment: roller, for spray application refer the datasheet ) G1.25NZ 3.00Kg/M 2 2000-15 min G1.02NZ 0.08 L/M 2 80 20 2 G2.01NZ 0.12 L/M 2 125 60 4 7 days 6 6 Recommended Uses Additional Notes Caution For exterior and interior use. Grano Sponge Finish may be applied to off-form concrete Class 2 (AS 1510) or equivalent, cement rendered fair-faced flush-jointed concrete block and brickwork (common, clay, concrete), tilt-up and pre-cast concrete, proprietary fibre cement boards and Autoclaved Aerated Concrete (AAC). See the appropriate system specification sheet for further details. Surface preparation is the responsibility of the Builder, Renovator or Main Contractor and the Applicator. To achieve the indicated performance, it must be carried out according to Wattyl s recommendations. It is recommended that application be carried out by a skilled applicator, who is totally conversant with the Wattyl Granosite products and systems, to validate full material Provide adequate ventilation during use. Application should not be carried out if the air temperature or the substrate temperature is below 10 o C or above 35 o C. The temperature must not fall below 10 o C during the drying process. 1. This information is provided with respect to the listed Wattyl products. Wattyl recommends that: (a) you review the Technical Data Sheets (TDS) and Material Safety Data Sheets (MSDS) before you use or handle the product; (b) the product be used only in accordance with the information provided by Wattyl; (c) the product be transported, stored and handled in accordance with the information on the MSDS and relevant TDS; and (d) you thoroughly test the product, using the recommended application method on a sample of intended substrate, before using the product. 2. The information in this specification sheet was prepared using information gathered during product development. While Wattyl endeavours to update this information and maintain the accuracy and currency of its contents, Wattyl cannot guarantee that the information provided is wholly comprehensive. 3. Wattyl recommends that you conduct such additional investigations as may be necessary to satisfy yourself of the accuracy, currency and comprehensiveness of the information on which you rely in using and handling the product. If you require further information please contact your nearest Wattyl Office. 4. To the full extent permitted by law, Wattyl's liability for breach of a condition or warranty implied into the contract for sale between Wattyl and you by law is limited at Wattyl's election to: (a) the replacement of the product; or (b) payment of the cost of replacing the product. WATTYL (NZ)

Paintworks Specification GS 425.3NZ Page 1 of 1 July 2004 System Substrate Category Grano Sponge Finish Satin Exterior New and uncoated brick & concrete block Premium Texture Water Based Product Features Grano Sponge Finish is a high performance pre blended modified cement based texturing material designed for use Grano Adhesive Mortar (G1.06NZ) or Grano Thin Bed Render (G1.09NZ). Grano Sponge Finish allows sponge, floated and various finishes to be achieved Surface Preparation Substrate must be free from dirt, dust, oil, grease, mould or any other contaminants that may affect adhesion. All scaling, efflorescence, mould, mastic compound or any other foreign material must be removed prior to painting. Remove all traces of loosely adhering material by scraping, grinding or wire brushing, etc. The success of any system is very much dependent on the correct construction of the framing, the installation/laying, fixing of the brick and concrete block and the application of the rendering materials themselves. Wattyl recommends that it is the responsibility of the Applicator to ensure that the substrate is of an acceptable standard prior to the application of any Granosite coating system. Surface preparation is the responsibility of the Builder, Renovator or Main Contractor and the Applicator. Render the new and uncoated brick & concrete blocks with the Grano Nu-Render or Nu-Solid rendering system for new and uncoated brick & concrete blocks. To access the Grano Nu-Render or Nu-Solid Installation Guides, contact Wattyl (NZ) Ltd for the regional Granosite Sales Consultant s contact details. Film Thickness Application Details Data Sheet Coverage (microns) Dry Times Wet Dry Touch Topcoat First Coat: Grano Sponge Finish (equipment: trowel to the desired effect) Second Coat: GranoPrime (equipment: roller or spray) Third & Fourth Coat: GranoImpact (equipment: roller, for spray application refer the datasheet ) G1.25NZ 3.00Kg/M 2 2000-15 min G1.02NZ 0.08 L/M 2 80 20 2 G2.01NZ 0.12 L/M 2 125 60 4 7 days 6 6 Recommended Uses For exterior and interior use. Grano Sponge Finish may be applied to off-form concrete Class 2 (AS 1510) or equivalent, cement rendered fair-faced flush-jointed concrete block and brickwork (common, clay, concrete), tilt-up and pre-cast concrete, proprietary fibre cement boards and Autoclaved Aerated Concrete (AAC). See the appropriate system specification sheet for further details. Additional Notes Caution Surface preparation is the responsibility of the Builder, Renovator or Main Contractor and the Applicator. To achieve the indicated performance, it must be carried out according to Wattyl s recommendations. It is recommended that application be carried out by a skilled applicator, who is totally conversant with the Wattyl Granosite products and systems, to validate full material warranty conditions. Provide adequate ventilation during use. Application should not be carried out if the air temperature or the substrate temperature is below 10 o C or above 35 o C. The temperature must not fall below 10 o C during the drying process. 1. This information is provided with respect to the listed Wattyl products. Wattyl recommends that: (a) you review the Technical Data Sheets (TDS) and Material Safety Data Sheets (MSDS) before you use or handle the product; (b) the product be used only in accordance with the information provided by Wattyl; (c) the product be transported, stored and handled in accordance with the information on the MSDS and relevant TDS; and (d) you thoroughly test the product, using the recommended application method on a sample of intended substrate, before using the product. 2. The information in this specification sheet was prepared using information gathered during product development. While Wattyl endeavours to update this information and maintain the accuracy and currency of its contents, Wattyl cannot guarantee that the information provided is wholly comprehensive. 3. Wattyl recommends that you conduct such additional investigations as may be necessary to satisfy yourself of the accuracy, currency and comprehensiveness of the information on which you rely in using and handling the product. If you require further information please contact your nearest Wattyl Office. 4. To the full extent permitted by law, Wattyl's liability for breach of a condition or warranty implied into the contract for sale between Wattyl and you by law is limited at Wattyl's election to: (a) the replacement of the product; or (b) payment of the cost of replacing the product. WATTYL (NZ)

Paintworks Specification GS 100.4NZ Page 1 of 1 October 2005 System Substrate Category GranoAntique Trowel Satin Exterior New and uncoated off form concrete Premium Texture Water Based Product Features GranoAntique is a trowel applied pigmented acrylic texture coating giving an elegant yet rustic fine grainy textured finish. Surface Preparation Ensure all new cementitious substrates are fully cured prior to painting. Typically this may take a minimum of 4-6 weeks. There must be less than 15% moisture wood equivalent in the surface at the time of application to ensure optimum coating performance. The surface must not be subject to frequent wetting or hydrostatic pressure. Any foreign material that may affect adhesion must be removed prior to coating. Grind off any protruding formwork joints. Patching or Skimming Imperfections: Examine surfaces closely for air holes and imperfections, patch or skim as required with GranoPatch Smooth (G1.04NZ). Block down, allow to dry, sand back and dust off. Rendering if required: Render surface with Grano Adhesive Mortar (G1.06NZ). Allow to cure 7 days. Film Thickness Application Details Data Sheet Coverage (microns) Dry Times Wet Dry Touch Topcoat First Coat: GranoPrime S (equipment: roller or spray) G1.03NZ 0.12 L/M 2 120 25 30 minutes 2 Second Coat: GranoAntique (equipment: Stainless Steel & Red Plastic Trowel) Third & Fourth Coat: GranoImpact (equipment: roller, for spray application refer the datasheet ) G2.11NZ 2.00 Kg/M 2 1105 670 4 G2.01NZ 0.12 L/M 2 125 60 4 24 6 Recommended Uses Additional Notes Caution For exterior or interior use. For use on suitably prepared off-form concrete Class 2 (AS 1510) or equivalent, cement rendered fairfaced flush-jointed concrete block and brickwork (common, clay, concrete, CFC, tilt-up and pre-cast concrete. See the appropriate system specification sheet for further details Surface preparation is the responsibility of the Builder, Renovator or Main Contractor and the Applicator. To achieve the indicated performance, it must be carried out according to Wattyl s recommendations. It is recommended that application be carried out by a skilled applicator, who is totally conversant with the Wattyl Granosite products and systems, to validate full material warranty conditions. Provide adequate ventilation during use. Application should not be carried out if the air temperature or the substrate temperature is below 10 o C or above 35 o C. The temperature must not fall below 10 o C during the drying process. 1. This information is provided with respect to the listed Wattyl products. Wattyl recommends that: (a) you review the Technical Data Sheets (TDS) and Material Safety Data Sheets (MSDS) before you use or handle the product; (b) the product be used only in accordance with the information provided by Wattyl; (c) the product be transported, stored and handled in accordance with the information on the MSDS and relevant TDS; and (d) you thoroughly test the product, using the recommended application method on a sample of intended substrate, before using the product. 2. The information in this specification sheet was prepared using information gathered during product development. While Wattyl endeavours to update this information and maintain the accuracy and currency of its contents, Wattyl cannot guarantee that the information provided is wholly comprehensive. 3. Wattyl recommends that you conduct such additional investigations as may be necessary to satisfy yourself of the accuracy, currency and comprehensiveness of the information on which you rely in using and handling the product. If you require further information please contact your nearest Wattyl Office. 4. To the full extent permitted by law, Wattyl's liability for breach of a condition or warranty implied into the contract for sale between Wattyl and you by law is limited at Wattyl's election to: (a) the replacement of the product; or (b) payment of the cost of replacing the product. WATTYL (NZ)

Paintworks Specification GS 100.7NZ Page 1 of 1 October 2005 System Substrate Category GranoAntique Trowel Satin Exterior New and uncoated tilt-up & pre-cast panels Premium Texture Water Based Product Features GranoAntique is a trowel applied pigmented acrylic texture coating giving an elegant yet rustic fine grainy textured finish. Surface Preparation The surface must be free from bondbreakers, release agents, dirt, dust, or other contaminants that may interfere with adhesion. Bondbreakers or release agents must be removed with a suitable proprietary cleaner as recommended by the tilt slab manufacturer. To test for bondbreakers, wet the surface. If the water beads and runs off, the bondbreaker has not been removed. If the water soaks into the surface the bondbreaker has been removed. Grind off any protruding formwork joints. Examine for air holes and defects, fill with GranoPatch Smooth (G1.04NZ), block down, sand to an even finish, dust off. Ensure all new cementitious substrates are fully cured prior to painting. Typically this may take a minimum of 4-6 weeks. There must be less than 15% moisture wood equivalent in the surface at the time of application to ensure optimum coating performance. Film Thickness Application Details Data Sheet Coverage (microns) Dry Times Wet Dry Touch Topcoat First Coat: GranoPrime S (equipment: roller or spray) G1.03NZ 0.12 L/M 2 120 25 30 minutes 2 Second Coat: GranoAntique (equipment: Stainless Steel & Red Plastic Trowel) Third & Fourth Coat: GranoImpact (equipment: roller, for spray application refer the datasheet ) G2.11NZ 2.00 Kg/ M 2 1105 670 4 G2.01NZ 012 L/M 2 125 60 4 24 6 Recommended Uses Additional Notes Caution For exterior or interior use. For use on suitably prepared off-form concrete Class 2 (AS 1510) or equivalent, cement rendered fairfaced flush-jointed concrete block and brickwork (common, clay, concrete), CFC, tilt-up and pre-cast concrete and Autoclaved Aerated Concrete (AAC). See the appropriate system specification sheet for further details. Surface preparation is the responsibility of the Builder, Renovator or Main Contractor and the Applicator. To achieve the indicated performance, it must be carried out according to Wattyl s recommendations. It is recommended that application be carried out by a skilled applicator, who is totally conversant with the Wattyl Granosite products and systems, to validate full material warranty conditions. Provide adequate ventilation during use. Application should not be carried out if the air temperature or the substrate temperature is below 10 o C or above 35 o C. The temperature must not fall below 10 o C during the drying process. 1. This information is provided with respect to the listed Wattyl products. Wattyl recommends that: (a) you review the Technical Data Sheets (TDS) and Material Safety Data Sheets (MSDS) before you use or handle the product; (b) the product be used only in accordance with the information provided by Wattyl; (c) the product be transported, stored and handled in accordance with the information on the MSDS and relevant TDS; and (d) you thoroughly test the product, using the recommended application method on a sample of intended substrate, before using the product. 2. The information in this specification sheet was prepared using information gathered during product development. While Wattyl endeavours to update this information and maintain the accuracy and currency of its contents, Wattyl cannot guarantee that the information provided is wholly comprehensive. 3. Wattyl recommends that you conduct such additional investigations as may be necessary to satisfy yourself of the accuracy, currency and comprehensiveness of the information on which you rely in using and handling the product. If you require further information please contact your nearest Wattyl Office. 4. To the full extent permitted by law, Wattyl's liability for breach of a condition or warranty implied into the contract for sale between Wattyl and you by law is limited at Wattyl's election to: (a) the replacement of the product; or (b) payment of the cost of replacing the product. WATTYL (NZ)

Data Sheet G1.06NZ Grano Adhesive Mortar formerly GranoPlast DESCRIPTION Page 1 of 2 Resource Code 849504 July 2004 Grano Adhesive Mortar Coarse or Fine is a high quality polymer modified, cementitious rendering material specifically designed for thin section rendering on expanded polystyrene sheets or blocks, bricks, AAC or over a base coat render. PRINCIPAL CHARACTERISTICS Suitable for interior or exterior use. Applies with exceptional ease to provide a good adhesive surface for a finishing texture or plaster. Can be applied between 4-5mm thicknesses in one application. Superior application and adhesion properties when compared to conventional sand and cement render. Easy to apply and being pumpable can offer economies in time and labour. As a finish texture COLOURS AND GLOSS Grey BASIC DATA AT 25 C Surface Dry Fifteen (15) minutes Recoat Twenty four (24), if required Fully Cured Seven (7) days All figures are quoted at 25 C and 50% Relative Humidity. Drying will take longer at lower temperatures or higher relative humidity. Consistency Dry powder Texture Grainy Pot-Life Fifteen (15) minutes when mixed. Coverage per coat 4.00Kg/M 2 per 4mm film thickness Clean-up Thoroughly clean equipment with water. Weatherability Excellent Abrasion Resistance Excellent RECOMMENDED SUBSTRATE CONDITIONS AND TEMPERATURE Grano Adhesive Mortar is suitable for application to Expanded Extruded Polystyrene Sheets and Blocks, and Autoclaved Aerated Concrete (AAC) blocks or panels, off-form concrete and any other fair-faced, flush and straight laid concrete block or brickwork (common, clay). Surface Preparation is the responsibility of the Builder, Renovator or Main Contractor and the Applicator. To achieve the indicated performance, application must be carried out according to Wattyl's recommendations. Ensure the surface is clean and dry. All substrates must be free of dirt, grease, oil, mould, release agents, bondbreakers or any other contaminants that may interfere with adhesion. There must be less than 15% moisture Wood Equivalent in the surface at the time of coating to ensure optimum coating performance. Note: Porous substrates must be sealed with GranoSeal (G1.14NZ) reduced 1:1 with water and applied by roller or spray at 0.12L/M 2 (8.3M 2 /L). Allow to dry 2-6 prior to applying Grano Adhesive Mortar. Application should not be carried out if the air temperature or the substrate temperature is below 5 C or above 35 C. Freshly applied material must be protected from frosts and rain for a minimum of forty eight (48). Not suitable for walk on surfaces.

Grano Adhesive Mortar Data Sheet G1.06NZ Page 2 of 2 Resource Code 849504 July 2004 INSTRUCTIONS FOR USE Mix one (1) 25 kg bag of Grano Adhesive Mortar to approximately 4.0 litres of water. Add the powder to the water steadily and mix with a power stirrer until it is smooth and lump free. Grano Adhesive Mortar has a pot-life of fifteen (15) minutes when mixed. Trowel one (1) coat of Grano Adhesive Mortar using a stainless steel trowel at 4.00Kg/M 2 per 4mm film thickness. Allow 24 to dry. Apply an additional coat of Grano Adhesive Mortar if required. Curing Keep damp for the first 12 to ensure full strength is developed. This is critical in windy conditions or when humidity is low. Allow to fully cure for 24 or when moisture content is no greater that 15% wood equivalent before top coating. For Nu-Therm or Nu-Lite systems refer the Installation Guide. SAFETY DATA Caution Provide adequate ventilation during use. Avoid inhalation of the powder, prolonged skin contact and particularly eye contact. Wear protective clothing to minimise skin contact and wear goggles where splatter is likely. Spills and Disposal Do not allow spilt material to enter drains or other watercourses. Sweep up and dispose of waste In sealed containers to minimise dust. Disposal of waste is subject to statutory control. Consult your local authority for disposal guidelines. M.S.D.S. A Material Safety Data Sheet (M.S.D.S.) is available on request. First Aid If swallowed do not induce vomiting. Give plenty of water to drink. Contact a doctor or the Poisons Information Centre. Phone 0800 764766 (New Zealand). If in eyes, hold eyes open and flood with water for at least 15 minutes. Contact a doctor if any irritation occurs. If on skin remove contaminated clothing, wash skin thoroughly with soap and water or a proprietary skin cleanser. Do not use solvents. If affected by inhalation remove person to fresh air. If breathing difficulties persist or occur later, contact a doctor. ADDITIONAL DATA Available in 25 kg bags. Bags must be kept dry during transportation and storage. Shelf Life: Six (6) months if stored appropriately. This must include storage under cover, above ground, away from direct heat and moisture and in well-sealed containers. It is recommended that application be carried out by a skilled applicator, who is totally conversant with the Granosite products and systems, to validate full material warranty conditions. For further information, contact the Wattyl Information Helpline. Phone 0800 735551 (New Zealand). GRANO ADHESIVE MORTAR IS A SURFACE PREPARATION PRODUCT AND IS USED IN CONJUNCTION WITH VARIOUS GRANOSITE SYSTEMS. AS SUCH IT IS NOT A SYSTEM IN ITSELF AND SHOULD ONLY BE USED WHERE SPECIFIED. 1. This information is provided with respect to the listed Wattyl products. Wattyl recommends that: (a) you review the Technical Data Sheets (TDS) and Material Safety Data Sheets (MSDS) before you use or handle the product; (b) the product be used only in accordance with the information provided by Wattyl; (c) the product be transported, stored and handled in accordance with the information on the MSDS and relevant TDS; and (d) you thoroughly test the product, using the recommended application method on a sample of intended substrate, before using the product. 2. The information in this technical data sheet was prepared using information gathered during product development. While Wattyl endeavours to update this information and maintain the accuracy and currency of its contents, Wattyl cannot guarantee that the information provided is wholly comprehensive. 3. Wattyl recommends that you conduct such additional investigations as may be necessary to satisfy yourself of the accuracy, currency and comprehensiveness of the information on which you rely in using and handling the product. If you require further information please contact your nearest Wattyl Office. 4. To the full extent permitted by law, Wattyl's liability for breach of a condition or warranty implied into the contract for sale between Wattyl and you by law is limited at Wattyl's election to: (a) the replacement of the product; or (b) payment of the cost of replacing the product. WATTYL (NZ) LTD

Data Sheet G1.25NZ Grano Sponge Finish formerly GranoSponge DESCRIPTION Page 1 of 2 Resource Code July 2004 Grano Sponge Finish is a high performance pre blended modified cement based texturing material designed for use over Grano Adhesive Mortar (G1.06NZ) or Grano Modified Render (G1.10NZ). PRINCIPAL CHARACTERISTICS Suitable for interior or exterior use. Formulated to produce sponge, floated and various other finishes. Can be applied between 2-3mm thicknesses in one application. Easy to apply and can being pumpable can offer economies in time and labour COLOURS AND GLOSS Grey BASIC DATA AT 25 C Surface Dry 15 minutes Recoat Twenty four (24), if required Fully Cured Seven (7) days All figures are quoted at 25 C and 50% Relative Humidity. Drying will take longer at lower temperatures or higher relative humidity. Consistency Dry powder Texture Grainy Pot-Life Two - Three (2-3) when mixed. Coverage per coat 3.00Kg/M 2 per 2mm film thickness Clean-up Thoroughly clean equipment with water. Weatherability Excellent Abrasion Resistance Excellent RECOMMENDED SUBSTRATE CONDITIONS AND TEMPERATURE Grano Sponge Finish is suitable for application to rendered surfaces such as Grano Adhesive Mortar (G1.06NZ) or Grano Modified Render (G1.10NZ). Surface Preparation is the responsibility of the Builder, Renovator or Main Contractor and the Applicator. To achieve the indicated performance, application must be carried out according to Wattyl's recommendations. Ensure the surface is clean and dry. All substrates must be free of dirt, grease, oil, mould, release agents, bondbreakers or any other contaminants that may interfere with adhesion. There must be less than 15% moisture Wood Equivalent in the surface at the time of coating to ensure optimum coating performance. Application should not be carried out if the air temperature or the substrate temperature is below 5 C or above 35 C. Freshly applied material must be protected from frosts and rain for a minimum of forty eight (48). Not suitable for walk on surfaces.

Grano Sponge Finish Data Sheet G1.25NZ Page 2 of 2 Resource Code 849504 July 2004 INSTRUCTIONS FOR USE Mix one (1) 25 kg bag of Grano Sponge Finish to approximately 4.0 litres of water. Add the powder to the water steadily and mix with a power stirrer until it is smooth and lump free. Grano Sponge Finish has a pot-life of 15 minutes when mixed. Trowel one (1) coat of Grano Sponge Finish using a stainless steel trowel at 3.00Kg/M 2 per 2mm film thickness. Allow 24 to dry. Apply an additional coat of Grano Sponge Finish if required. Curing Keep damp for the first 12 to ensure full strength is developed. This is critical in windy conditions or when humidity is low. Allow to fully cure for 7 days or when moisture content is no greater that 15% wood equivalent before top coating. SAFETY DATA Caution Provide adequate ventilation during use. Avoid inhalation of the powder, prolonged skin contact and particularly eye contact. Wear protective clothing to minimise skin contact and wear goggles where splatter is likely. Spills and Disposal Do not allow spilt material to enter drains or other watercourses. Sweep up and dispose of waste In sealed containers to minimise dust. Disposal of waste is subject to statutory control. Consult your local authority for disposal guidelines. M.S.D.S. A Material Safety Data Sheet (M.S.D.S.) is available on request. First Aid If swallowed do not induce vomiting. Give plenty of water to drink. Contact a doctor or the Poisons Information Centre. Phone 0800 764766 (New Zealand). If in eyes, hold eyes open and flood with water for at least 15 minutes. Contact a doctor if any irritation occurs. If on skin remove contaminated clothing, wash skin thoroughly with soap and water or a proprietary skin cleanser. Do not use solvents. If affected by inhalation remove person to fresh air. If breathing difficulties persist or occur later, contact a doctor. ADDITIONAL DATA Available in 25 kg bags. Bags must be kept dry during transportation and storage. Shelf Life: Six (6) months if stored appropriately. This must include storage under cover, above ground, away from direct heat and moisture and in well-sealed containers. It is recommended that application be carried out by a skilled applicator, who is totally conversant with the Granosite products and systems, to validate full material warranty conditions. For further information, contact the Wattyl Information Helpline. Phone 0800 735551 (New Zealand). GRANO SPONGE FINISH IS A SURFACE PREPARATION PRODUCT AND IS USED IN CONJUNCTION WITH VARIOUS GRANOSITE SYSTEMS. AS SUCH IT IS NOT A SYSTEM IN ITSELF AND SHOULD ONLY BE USED WHERE SPECIFIED. 1. This information is provided with respect to the listed Wattyl products. Wattyl recommends that: (a) you review the Technical Data Sheets (TDS) and Material Safety Data Sheets (MSDS) before you use or handle the product; (b) the product be used only in accordance with the information provided by Wattyl; (c) the product be transported, stored and handled in accordance with the information on the MSDS and relevant TDS; and (d) you thoroughly test the product, using the recommended application method on a sample of intended substrate, before using the product. 2. The information in this technical data sheet was prepared using information gathered during product development. While Wattyl endeavours to update this information and maintain the accuracy and currency of its contents, Wattyl cannot guarantee that the information provided is wholly comprehensive. 3. Wattyl recommends that you conduct such additional investigations as may be necessary to satisfy yourself of the accuracy, currency and comprehensiveness of the information on which you rely in using and handling the product. If you require further information please contact your nearest Wattyl Office. 4. To the full extent permitted by law, Wattyl's liability for breach of a condition or warranty implied into the contract for sale between Wattyl and you by law is limited at Wattyl's election to: (a) the replacement of the product; or (b) payment of the cost of replacing the product. WATTYL (NZ) LTD

Data Sheet G1.02NZ GranoPrime Page 1 of 2 Resource Code 849405 July 2004 DESCRIPTION GranoPrime is an acrylic primer sealer. GranoPrime can be applied by brush, roller or spray, prior to the application of most of the Wattyl Granosite texture systems. PRINCIPAL CHARACTERISTICS Suitable for interior or exterior use. Ensures optimum performance of the complete coating system by stabilising irregularities in substrate absorption and mechanical strength. Speeds the application, controls the drying and ensures strong adhesion of topcoats to the substrate. On concrete, cement render and mortar joints, the use of GranoPrime minimises the threat of loss of adhesion or other problems that may arise due to presence of residual alkali salts. As an acrylic, GranoPrime is not subject to the degradation that can occur with polyvinyl acetates (PVAs) in an alkaline environment. COLOURS AND GLOSS Off-white BASIC DATA AT 25 C Surface Dry Two (2) Recoat Two (2) to six (6) All figures are quoted at 25 C and 50% Relative Humidity. Drying will take longer at lower temperatures or higher relative humidity. Density 1.04 kg/l Consistency Milky liquid Coverage per coat 0.08L/M 2 (12.5M 2 /L) Wet Film Thickness 80 microns (approx) Dry Film Thickness 20 microns (approx) Thinning High Absorption Substrates Mix 1 part GranoPrime with 1 part water. Medium Absorption Substrates Mix 2 parts GranoPrime with 1 part water. Low Absorption Substrates Use GranoPrime undiluted. Clean-up Thoroughly clean equipment with water. RECOMMENDED SUBSTRATE CONDITIONS AND TEMPERATURE High Absorption Substrates: Concrete block, cement render, brick, CFC and fibre cement sheeting, CSR Hebel Autoclaved Aerated Concrete (AAC), coloured renders, lime washes, Grano Adhesive Mortar (G1.06NZ), Grano Modified Render (G1.10NZ), GranoReady Render (G1.12NZ), GranoPatch Smooth (G1.04NZ), GranoFlex (G1.15NZ). Medium Absorption Substrates: Off-form concrete under 40mpa, Polystyrene panels. Low Absorption Substrates: Previously painted surfaces, off-form concrete over 40mpa, high density bricks. GranoPrime is not suitable for application to steel or timber substrates. Surface Preparation is the responsibility of the Builder, Renovator or Main Contractor and the Applicator. To achieve the indicated performance, application must be carried out according to Wattyl's recommendations. Ensure the surface is clean and dry. All substrates must be free of dirt, grease, oil, mould, release agents, bondbreakers or any other contaminants that may interfere with adhesion. Fresh concrete substrates should be left for a minimum of 28 days before coating; fresh plaster surfaces should be left for a minimum of 14 days. There must be less than 15% moisture Wood Equivalent in the surface at the time of coating to ensure optimum coating performance. Application should not be carried out if the air temperature or the substrate temperature is below 10 C or above 35 C. The temperature must not fall below 10 C during the drying process. Freshly applied material must be protected from frosts and rain for a minimum of forty eight (48).

GranoPrime Data Sheet G1.02NZ Page 2 of 2 Resource Code 849405 July 2004 INSTRUCTIONS FOR USE Stir contents thoroughly with a power stirrer before use. Apply one (1) coat to a correctly prepared surface by brush, roller or spray. Airless Spray Settings: Tip - 519-521 Pressure - 1500 2000 psi SAFETY DATA Caution Provide adequate ventilation during use. Spills and Disposal Do not allow spilt material to enter drains or other watercourses. Absorb spills with sand or other inert material. Unwanted paint should be kept in a sealed container, such as an empty paint can, and disposed of via special waste collection services. Check with your local Council regarding the disposal of empty paint containers M.S.D.S. A Material Safety Data Sheet (M.S.D.S.) is available on request. First Aid If swallowed do not induce vomiting. Give plenty of water to drink. Contact a doctor or the Poisons Information Centre. Phone 0800 764766 (New Zealand). If in eyes, hold eyes open and flood with water for at least 15 minutes. Contact a doctor if any irritation occurs. If on skin remove contaminated clothing, wash skin thoroughly with soap and water or a proprietary skin cleanser. Do not use solvents. If affected by inhalation remove person to fresh air. If breathing difficulties persist or occur later, contact a doctor. ADDITIONAL DATA Available in 15 litre containers. Containers must be secured and stored upright during transit. Containers must not be exposed to excessive heat or cold. Storage must be under cover, away from direct heat, freezing and moisture, in well-sealed containers. It is recommended that application be carried out by a skilled applicator, who is totally conversant with the Granosite products and systems, to validate full material warranty conditions. For further information, contact the Wattyl Information Helpline. Phone 0800 735551 (New Zealand). GRANOPRIME IS A SURFACE PREPARATION PRODUCT AND IS USED IN CONJUNCTION WITH VARIOUS WATTYL GRANOSITE SYSTEMS. AS SUCH IT IS NOT A SYSTEM IN ITSELF AND SHOULD ONLY BE USED WHERE SPECIFIED. 1. This information is provided with respect to the listed Wattyl products. Wattyl recommends that: (a) you review the Technical Data Sheets (TDS) and Material Safety Data Sheets (MSDS) before you use or handle the product; (b) the product be used only in accordance with the information provided by Wattyl; (c) the product be transported, stored and handled in accordance with the information on the MSDS and relevant TDS; and (d) you thoroughly test the product, using the recommended application method on a sample of intended substrate, before using the product. 2. The information in this technical data sheet was prepared using information gathered during product development. While Wattyl endeavours to update this information and maintain the accuracy and currency of its contents, Wattyl cannot guarantee that the information provided is wholly comprehensive. 3. Wattyl recommends that you conduct such additional investigations as may be necessary to satisfy yourself of the accuracy, currency and comprehensiveness of the information on which you rely in using and handling the product. If you require further information please contact your nearest Wattyl Office. 4. To the full extent permitted by law, Wattyl's liability for breach of a condition or warranty implied into the contract for sale between Wattyl and you by law is limited at Wattyl's election to: (a) the replacement of the product; or (b) payment of the cost of replacing the product. WATTYL (NZ) LTD

Data Sheet G2.11NZ GranoAntique Page 1 of 2 Resource Code 849528 July 2004 DESCRIPTION GranoAntique is a trowel applied pigmented acrylic texture coating giving an elegant yet rustic fine grainy textured finish. GranoAntique may be left matt or overcoated with GranoImpact (G2.01NZ) or GranoSkin Membrane (G5.02NZ) for enhanced durability. PRINCIPAL CHARACTERISTICS Suitable for interior or exterior use. GranoAntique may be used to decorate, restore and protect commercial buildings, resorts, high-rise buildings, homes and offices. GranoAntique is an economical and long lasting means for creating lightweight stone-like finishes over most cementitious substrates. GranoAntique is water-based for applicator safety and ease of use. COLOURS AND GLOSS Off white. May be tinted as required. Refer to the Wattyl colour range including the authentic heritage range. May also be tinted to other competitor colour ranges through the Wattyl tinting system. It is recommended that, for exterior application, the light-fastness of the chosen colour be confirmed before ordering. Matt. Satin when overcoated by GranoImpact (G2.01NZ) or GranoSkin Membrane (G2.14NZ). Colours of Light Reflectance Values (LRV) of less than 40% on fibrecement substrates and less than 35% on polystyrene boards or to polystyrene block permanent formwork substrates may result in unacceptable thermal movement and should not be used. BASIC DATA AT 25 C Surface Dry Four (4) Topcoat Twenty-four (24) Fully Cured Seven (7) days All figures are quoted at 25 C and 50% Relative Humidity. Drying will take longer at lower temperatures or higher relative humidity. Density 1.88 Kg/L Consistency Thick grainy paste. Texture Uniform grainy stone-like texture Coverage per coat 2.00 Kg/M 2 Wet Film Thickness 1105 microns (approx) Dry Film Thickness 670 microns (approx) Moisture Control Excellent when topcoated, however the coating must not be subject to hydrostatic pressure. Abrasion Resistance Excellent Thinning No thinning required, but if desired thin sparingly with water. Clean-up Thoroughly clean equipment with water. RECOMMENDED SUBSTRATE CONDITIONS AND TEMPERATURE GranoAntique may be applied to off-form concrete Class 2 (AS 1510) or equivalent, cement rendered fair-faced flushjointed concrete block and brickwork (common, clay, concrete), CFC, and fibre cement sheeting, tilt-up and pre-cast concrete, Autoclaved Aerated Concrete (AAC). Make-good of substrate is necessary if substrate imperfections are to be eliminated. Please refer to separate Datasheets for Grano Adhesive Mortar (G1.06NZ) or Grano Modified Render (G1.10NZ), GranoPatch Smooth (G1.04NZ), GranoFlex (G1.15NZ) or GranoReady Render (G1.12NZ). Surface Preparation is the responsibility of the Builder, Renovator or Main Contractor and the Applicator. To achieve the indicated performance, application must be carried out according to Wattyl's recommendations.

GranoAntique Data Sheet G2.11NZ Page 2 of 2 Resource Code 849528 July 2004 RECOMMENDED SUBSTRATE CONDITIONS AND TEMPERATURE Ensure the surface is clean and dry. All substrates must be free of dirt, dust, grease, oil, mould release agents, bond breakers and any other contaminants that may interfere with adhesion. Fresh concrete substrates should be left for a minimum of 28 days before coating; fresh plaster surfaces should be left for a minimum of 14 days. There must be less than 15% moisture Wood Equivalent in the surface at the time of coating to ensure optimum coating performance. Application should not be carried out if the air temperature or the substrate temperature is below 10 C or above 35 C. The temperature must not fall below 10 C during the drying process. Freshly applied material must be protected from frosts and rain for a minimum of forty eight (48). Not suitable for walk on surfaces. For specific substrate preparation, see relevant specification sheets. INSTRUCTIONS FOR USE Stir contents thoroughly with a power stirrer before use. GranoAntique is applied in one (1) coat by stainless steel trowel to a correctly prepared and GranoBasecoat primed (G1.11) surface then finished using the red plastic trowel. GranoAntique may be left matt or is overcoated with GranoImpact (G2.01NZ) or GranoSkin Membrane (G2.14NZ). SAFETY DATA Caution Provide adequate ventilation during use. Spills and Disposal Do not allow spilt material to enter drains or other watercourses. Absorb spills with sand or other inert material. Unwanted paint should be kept in a sealed container, such as an empty paint can, and disposed of via special waste collection services. Check with your local Council regarding the disposal of empty paint containers M.S.D.S. A Material Safety Data Sheet (M.S.D.S.) is available on request. First Aid If swallowed do not induce vomiting. Give plenty of water to drink. Contact a doctor or the Poisons Information Centre. Phone 0800 764766 (New Zealand). If in eyes, hold eyes open and flood with water for at least 15 minutes. Contact a doctor if any irritation occurs. If on skin remove contaminated clothing, wash skin thoroughly with soap and water or a proprietary skin cleanser. Do not use solvents. If affected by inhalation remove person to fresh air. If breathing difficulties persist or occur later, contact a doctor. ADDITIONAL DATA Available in 15 litre (27 Kg) containers. Containers must be secured and stored upright during transit. Containers must not be exposed to excessive heat or cold. Storage must be under cover, away from direct heat, freezing and moisture, in well-sealed containers. It is recommended that application be carried out by a skilled applicator, who is totally conversant with the Granosite products and systems, to validate full material warranty conditions. For further information, contact the Wattyl Information Hotline. Phone 132101(Australia). 1. This information is provided with respect to the listed Wattyl products. Wattyl recommends that: (a) you review the Technical Data Sheets (TDS) and Material Safety Data Sheets (MSDS) before you use or handle the product; (b) the product be used only in accordance with the information provided by Wattyl; (c) the product be transported, stored and handled in accordance with the information on the MSDS and relevant TDS; and (d) you thoroughly test the product, using the recommended application method on a sample of intended substrate, before using the product. 2. The information in this technical data sheet was prepared using information gathered during product development. While Wattyl endeavours to update this information and maintain the accuracy and currency of its contents, Wattyl cannot guarantee that the information provided is wholly comprehensive. 3. Wattyl recommends that you conduct such additional investigations as may be necessary to satisfy yourself of the accuracy, currency and comprehensiveness of the information on which you rely in using and handling the product. If you require further information please contact your nearest Wattyl Office. 4. To the full extent permitted by law, Wattyl's liability for breach of a condition or warranty implied into the contract for sale between Wattyl and you by law is limited at Wattyl's election to: (a) the replacement of the product; or (b) payment of the cost of replacing the product. WATTYL (NZ) LTD INFORMATION HOTLINE Ph: 0800 835551 (NEW ZEALAND)

Data Sheet G2.01NZ GranoImpact Page 1 of 3 Resource Code 84943 - Line June 2007 DESCRIPTION GranoImpact is a pure acrylic, high performance elastomeric coating able to be applied in a variety of styles by roller or spray. Approved to APAS 0118/2 & APAS 0117/3. PRINCIPAL CHARACTERISTICS Suitable for interior or exterior use. GranoImpact systems have good adhesion to a wide variety of substrates and have excellent resistance to mould and fungi. As an acrylic membrane, the vapour permeability of GranoImpact is carefully controlled to form a barrier to external moisture, while allowing vapour in the substrate to escape. It is, however, not suitable for situations where hydrostatic pressure exists. GranoImpact also forms the final topcoat of many other Granosite systems, extending the performance and overall protection of the system applied. GranoImpact is water-based for applicator safety and ease of use. COLOURS AND GLOSS Bases may be tinted as required. Refer to the Wattyl colour range including the authentic heritage range. May also be tinted to other competitor colour ranges through the Wattyl tinting system. It is recommended that, for exterior application, the light-fastness of the chosen colour be confirmed before ordering. Satin Colours of Light Reflectance Values (LRV) of less than 40% shall not be used on substrates as specified in NZBC Acceptable Solution E2/AS1 Section 2.4 Cladding Finish Colours. For other substrates Colours of Light Reflectance Values (LRV) of less than 40% may result in unacceptable thermal movement and we caution the use of darker colours. BASIC DATA AT 25 C Surface Dry Four (4) Recoat Six (6) Hard Dry Seven (7) days All figures are quoted at 25 C and 50% Relative Humidity. Drying will take longer at lower temperatures or higher relative humidity. Density 1.33 Kg/L Consistency Thick, creamy paste. Texture Low Profile High Profile Airless (10-12mm pile roller) (Fine black texture roller) (Airless spray gun) Coverage per coat 0.18 L/M 2 (5.5M 2 /L) 0.50 L/M 2 (2.0M 2 /L) 0..33 L/M 2 (3.0M 2 /L) Wet Film Thickness (per coat) 180 microns (approx) 500 microns (approx) 330 microns (approx) Dry Film Thickness (per coat) 85 microns (approx) 240 microns (approx) 160 microns (approx) Moisture Control Excellent, however the coating must not be subject to hydrostatic pressure. Water Ponding 50.5 - Excellent. (mg of water passed after 50 at 25 C and 50% relative humidity) Water Swelling 39.6. (ASTM D-471 % increase weight by weight) Water Permeability Passed (AS 2904 Appendix G - 6 metre head of water) Vapour Permeability 12.6 (gm/ m 2 /24 hrs) DIN 52615 (at 500um dry film build) Vapour Transmission 25.0 (gm/m 2 /24hrs) ASTM-E-96 (at 360um dry film build) Carbon Dioxide Diffusion Rb =459.6m (Engelfried Method) Chloride Ion Diffusion 1.3 x 10-9 cm 2 sec -1 (Taywood in-house method) Abrasion Resistance 5,000 cycles - Film integrity excellent (AS 1580 459.1) Salt Spray No effect (AS 2331.3.1) Elongation 524% (ASTM D-412 at 25 C) Tensile Strength 36.4 kg/cm 2 (ASTM D-412 at 25 C) Crack Bridging 3.65 (Crack width bridged per unit dry film thickness) Dirt Pick-Up 1 - on a scale of 0-5 where "0" is no dirt retained (AS 1580 481.1.4 12 months)

GranoImpact Data Sheet G2.01NZ BASIC DATA AT 25 C - continued Page 2 of 3 Resource Code 84943 - Line June 2007 Early Fire Hazard Ignitability (0-20) 11 (AS 1530.3) Spread of Flame (0-10) 0 Heat Evolved (0-10) 2 Smoke Developed (0-10) 3 Thinning Not required, but may be thinned with up to 10% water for cutting in and spray applications. Thinning rates for airless spray will vary according to the brand of equipment used. Clean up Thoroughly clean equipment with water. RECOMMENDED SUBSTRATE CONDITIONS AND TEMPERATURE GranoImpact may be applied to off-form concrete Class 2 (AS 1510) or equivalent, cement rendered fair-faced flushjointed concrete block and brickwork (common, clay, concrete), CFC, tilt-up and pre-cast concrete and paperfaced plasterboard. Make-good of the substrate is necessary if substrate imperfections are to be eliminated. Please refer to separate Datasheets for Grano Adhesive Mortar (G1.06NZ) or Grano Modified Render (G1.10NZ), GranoPatch Smooth (G1.04NZ). Surface Preparation is the responsibility of the Builder, Renovator or Main Contractor and the Applicator. To achieve the indicated performance, application must be carried out according to Wattyl's recommendations. Ensure the surface is clean and dry. All substrates must be free of dirt, dust, grease, oil, mould release agents, bondbreakers and any other contaminants that may interfere with adhesion. Fresh concrete substrates should be left for a minimum of 28 days before coating; fresh plaster surfaces should be left for a minimum of 14 days. There must be less than 15% moisture Wood Equivalent in the surface at the time of coating to ensure optimum coating performance. Application should not be carried out if the air temperature or the substrate temperature is below 10 C or above 35 C. The temperature must not fall below 10 C during the drying process. Freshly applied material must be protected from frosts and rain for a minimum of forty eight (48). Not suitable for roofs, ponds etc or walk on surfaces. For specific substrate preparation, see relevant specification sheets. INSTRUCTIONS FOR USE Stir contents thoroughly with a power stirrer before use. GranoImpact is normally applied in a two (2) coat application by roller to achieve the desired texture finish or the specified dry film thickness to a correctly prepared and primed surface. GranoImpact may be applied as a single finish coat on texture finishes over correctly prepared and primed surfaces by airless spray; however care must be taken to ensure an even overall finish is obtained. AIRLESS GUN SETTINGS Tip 519 or 521 Pressure Setting 2500 to 3000 psi SAFETY DATA Caution Provide adequate ventilation during use. Spills and Disposal Do not allow spilt material to enter drains or other watercourses. Absorb spills with sand or other inert material. Unwanted paint should be kept in a sealed container, such as an empty paint can, and disposed of via special waste collection services. Check with your local Council regarding the disposal of empty paint containers M.S.D.S. A Material Safety Data Sheet (M.S.D.S.) is available on request. First Aid If swallowed do not induce vomiting. Give plenty of water to drink. Contact a doctor or the Poisons Information Centre. Phone 0800 764766 (New Zealand). If in eyes, hold eyes open and flood with water for at least 15 minutes. Contact a doctor if any irritation occurs. If on skin remove contaminated clothing, wash skin thoroughly with soap and water or a proprietary skin cleanser. Do not use solvents. If affected by inhalation remove person to fresh air. If breathing difficulties persist or occur later, contact a doctor.