Torch on ccessories Technical Data Sheet Prefabricated corners made of polimeric bituminous membrane The bituminous prefabricated corners are made by hot folding of a unique piece of bituminous membrane with composite reinforcement. The main advantage is the total melting to the waterproofing sheet allowing flexibility during installation, which will give a total waterproofing guarantee on the most risky points. Torch on ituminous Fillet (bond breaker) Like with the bituminous corner profiles, the torch on bituminous fillet (bond breaker) is obtained via the hot bending of a bituminous membrane with composite reinforcement. It has a length of 1100mm. Internal ituminous Corner LIMITTIONS: not to be used with Index Proteaduo. LIMITTIONS: not to be used UNDER Index Proteaduo (due to having an SS base layer). 200mm 200mm Degree 90 Product Code: 744060 External ituminous Corner C L 45mm 45mm 1100mm Product Code: 744050 Roof Drain (dropper) made of TPE (Thermoplastic Elastomer s) with a 170mm spigot Manufactured of a special compound of thermoplastic rubber, it is highly resistant against low temperatures ( cold flexibility down to -40 ) as well as perfectly compatible with all sorts of bituminous waterproofing membrane. The traditional dove-tail channels and special shagreens on the flange allow a perfect bond to the membrane making the seal 100% effective. LIMITTIONS: not to be used UNDER Index Proteaduo (due to having an SS base layer). 162mm 335mm 170mm Degree 270 Product Code: 744040 Page 1 ugust 2014
Torch on ccessories - 80mm Dropper 305mm D1 74mm D2 78mm D3 74mm 170mm Pipe Sealing - Torch on Pipe Detailing Collar in TPE(Thermoplastic Elastomer s) Product Code: 744080 80mm - 100mm Dropper 335mm D1 93mm D2 97mm D3 89mm 170mm Product Code: 744070 100mm Parapete Drain Outlet - oy Type TPE (Thermoplastic Elastomer s) angular drain - (Spitter) 100mm x 65mm x 90 angle) D D1 D2 40mm 175mm 395mm 190mm Product Code: 744010 Torch on Domed Grate 60-120mm Torch on leaf guard for drainage outlets (flexible) C E L1 L2 340mm 62mm 92mm 145mm 168mm 425mm 425mm Product Code: 744090 Product Code: 744020 Page 2
Torch on ccessories One Way Vent - Torch on one way vent - Two piece torch on one way vent - designed for use with insulation panels The One Way Vent is a moisture relief device consisting of a two-piece polyethylene vent that allows moisture vapour to escape out of the roof deck system without allowing moisture to enter through the vent. Uses One Way Vents are most commonly used in re-roofing applications. listers caused by internal moisture in old roofing systems may be prevented or reduced by using One Way Vents. One Way Vents allow for continual release of vapour from within the system, while maintaining the watertight integrity from the outside. Installation Spacing Dependant on existing substrate moisture content and the vent sheet chosen, One Way Vents may be installed as per below: - insulation vent 300mm 225mm 1 190mm Product Code: 771183 Index Perfobase: 1 every 40-100m² Index Rollbase: 1 every 50-100m² Index Vapordiffuser: 1 every 100m² - single vent 300mm 225mm Product Code: 744030 Page 3
Torch on ccessories Pressure Seal Flashing luminium strips for sealing and flashing the edge of sheet membranes. Uses Parchem Pressure Seal Flashing is used to seal and flash the edge of Index torch applied bituminous membrane range of products and Emer-Proof DPE and D self-adhesive sheet membranes. The flashing strip is mechanically fixed, (with 150mm spacing between fixings), with the top edge sealed with a high performance, flexible sealant such as Emer-Seal MS or bituminous mastic, such as Nitoseal M175 (formally Plastiseal). dvantages Mechanically fixed through the membrane preventing the membrane from slumping Grooved in the centre of the strip for locating the drill Sold seperately : 3 metre lengths 45mm high (total) 2mm thick Product code: 752016 Extruded aluminium strips designed specifically for sealing and flashing the edge of Index torch applied sheet membranes and Emer-Proof DPE and D self-adhesive sheet membranes. This pressure seal was designed in-house at Parchem for the specific purpose of sealing off the Index bituminous torch applied membrane range and Emer-Proof DPE and D range of self-adhesive sheet membranes. Page 4
Torch on ccessories elasto-ring Plastic support ring for concrete pavers with leveling adjustment Uses elasto-ring is designed to be easily divided into fractions: For the row of slabs adjacent to the surrounding wall, the half ring is used For the slabs at the angle, the fourth ring is used To set the three slabs on an external angle, the three quartes ring is used The leveling disk is a elasto-ring accessory that is applied Iike a wedge, in order to stabilise the slabs that are not sufficiently flat, or when the surface is irregular. Generally it is used in quarters and put between the elastoring and the corner of the unstable slab. In terraces that are not exactly multiples of the slab measurements, the row touching the surrounding wall must be cut, or, as in the case of smaller measurements, the free space between the floor and the projecting part can be fllled with pebbles. The drainholes are installed at the waterproofing blanket level and furnished with a flat leaf filter. The joints between the slabs are not to be filled. They should be left free to promote rapid water drainage. For flooring to be installed over heat insulation, the insulatlng material should have a compressive strength superior to 2 kg/cm². With elasto-ring, the pavement does not touch the waterproofing blanket, but is separated from it by a hollow space; in this way, the pavement can expand and contract without damaging the water-tight blanket. elasto-ring is simply dry set onto the waterproofing. To install the square paving slabs on the supporting elastorings, it is enough to set the slabs at the four angles of the ring and push them against the spacer; once the first row is measured and set, the successive ones follow as a consequence. elasto-ring can be set on multilayer bituminous waterproofing, on bituminous sheathing waterproofing or on synthetic sheet waterproofing. The floor is completely precast. It is dry set; mortar is not needed. It can be installed in any season. Specialised workmen are not needed. nd it is without joints in that they are already included in the storing mounting. The slabs are only resting in place, and in case of repairs to the waterproofing blanket, it is not necessary to damage the floor; it is sufficient to raise a few of the square slabs to carry out the maintenance. Puddles can no longer form since rainwater runs directly to the drains between the open joints and the square slabs. Product: Index elasto-ring (ase Unit): Product Code: 771197 Index elasto-ring Leveler (djusts height in 3mm Increments): Product Code: 771198 pprox. eight 15mm 3mm (max. 4 Levelers per elasto-ring = 12mm) Concrete terraces cast directly onto waterproofing blanket can cause considerable problems. During the day the paving, heated by the sun, expands; at night, when the sun s heat ceases, the paving cools and therefore contracts. This alternating movement, which is concentrated along the expansion joints of the floor, is transmitted then to the underlying waterproofing blanket, damaging it through fatigue. To eliminate this problem it is necessary to isolate the floor the floor from the waterproofing underneath. Index has resolved this problem with elasto-ring, a plastic mounting for square paving slabs in precast concrete. Page 5
Torch on ccessories Torch on Guns and ccessories Gas torch stem short 220mm Gas torch small, including hose and regulator Product Code: 771206 Gas torch stem long 480mm Product Code: 742082 Gas torch head small 771195 50mm Gas torch large, including hose and regulator Product Code: 771207 Product Code: 742092 Gas torch head large 771196 70mm Important notice Safety Data Sheet (SDS) and Technical Data Sheet (TDS) are available from the Parchem website or upon request from the nearest Parchem sales office. Read the SDS and TDS carefully prior to use as application or performance data may change from time to time. In emergency, contact any Poisons Information Centre (phone 13 11 26 within ustralia) or a doctor for advice. Product disclaimer This Technical Data Sheet (TDS) summarises our best knowledge of the product, including how to use and apply the product based on the information available at the time. You should read this TDS carefully and consider the information in the context of how the product will be used, including in conjunction with any other product and the type of surfaces to, and the manner in which, the product will be applied. Our responsibility for products sold is subject to our standard terms and conditions of sale. Parchem does not accept any liability either directly or indirectly for any losses suffered in connection with the use or application of the product whether or not in accordance with any advice, specification, recommendation or information given by it. Page 6 Parchem Construction Supplies Pty Ltd 7 Lucca Road, Wyong NSW 2259 Phone: 1300 737 787 www.parchem.com.au N 80 069 961 968 Distributed in New Zealand by: Concrete Plus Ltd 23 Watts Rd, Sockburn 8042 Ph: 03 343 0090