MARMOX CONSTRUCTION BOARDS

Introduction MARMOX CONSTRUCTION BOARDS Marmox Construction Boards provide a quick cost effective solution tile backer with thermal insulating properties. These innovative construction boards are an ideal substrate for thin bed tiling on walls and floors or render finishes. In order to make installation simple, our range of construction boards include all solutions and possible applications, furthermore it is accompanied with all necessary fixing systems. How are Marmox Boards manufactured? Marmox Boards are made from extruded polystyrene with high water proofing and insulation properties. They are covered from both sides with a fibre mesh (to provide mechanical resistance) embedded in a polymerised cement mortar. This combination provides to the system a very good mechanical resistance, water proofing and bond to tile adhesive. Cement slurry Fiber glass mesh XPS foam Fiber glass mesh Cement slurry Where Marmox Boards are used? - Flooring underlay boards - Wall cladding and tile backing - Bath surrounds - Pipes coverings - Toilet boxes - Bathroom elements - Under floor heating underlays 5

Marmox construction boards 1/ TYPES OF MARMOX BOARDS 1.1 Standard Marmox Boards Standard Marmox Boards are available in two lengths: 125 and 250 cm, and widths of 60 and 120 cm. The thicknesses of these boards varies from 4 mm up till 100 mm according to the requirements. Marmox PRO Boards are characterized by their honeycomb surface finishing. This new innovative finishing provides professionals the following enhanced properties: - More strength thanks to the extra bond between the cement mortar and the reinforcing fiber glass mesh - Better adhering properties - Better water proofing CHOOSING HONEYCOMB FINISHING MEANS CHOOSING A PROFESSIONAL SOLUTION The new Honeycomb finishing, the finishing for professionals!! 6MARMOX CONSTRUCTION BOARDS

Characteristics 2 - High compressive strength (withstands 30 t/m ) at 10% deflection - Rigid - Very good water proofing properties - Excellent heat insulation - Easy to cut with a knife or saw - Extruded polystyrene closed cell structure - Light weight - Marmox is environmentally friendly, it is CFC and HCFC free Property Standard Result Thermal conductivity (5 years) DIN 52612 0.034 + 0.02 Compressive strength DIN 53421 2 300 KN/m at 10% deflection Water absorption (capillary) DIN 53428 Negligible Flammability BS 476 part 6,7 Class 0 EN 13501 E coeff. of thermal expansion ASTM D-696 30 x 10-6 Standard dimensions Reference Thickness Width Length U-value (W/m 2 K) 4MB125 4 10 1250 6MB125 6 7 10MB250 10 3.5 12.5MB250 12.5 2.7 20MB250 20 600 1.5 30MB250 30 2500 1 40MB250 40 0.7 50MB250 50 0.57 80MB250 80 0.35 7

Marmox construction boards Marmox Board on walls Marmox construction boards are fixed vertically to timber, brick, concrete or metal frame walls. For better thermal insulation use thicker boards (min. 20 mm) closely butted. Metal and timber frame walls Procedure - Vertical studs are at 600 mm, noggins at 600 mm. - Board edges must be supported by noggin. - Cut around all penetrations. 2 - Use 8 galvanized screws per m, min. 30 mm from edges. - Screw to be tightened till washers bite the board surface then level the washers with a rubber malet. - Cover joints by self adhesive fiber glass tape embedded in a layer of flexible tile adhesive. - Once the adhesive has hardened tiles can be fixed and grouted. MARMOX CONSTRUCTION BOARDS With timber frame With metal frame Water proofing For water proof construction all joints, penetrations and fastener locations must be treated by approved polyurethane water proofing agents as per manufacturer's recommendation. Brick and concrete walls Even walls procedure - For clean and sound wall use flexible tile adhesive. Coat the wall surface or apply an adhesive directly to the board surface (min. thickness 10 mm) - Comb out with 10 mm trowel creating a ribbed adhesive bed. Offer up boards and align vertically and horizontally. Bed firmly into place. - If adhesion can not be achieved by adhesive use dowels, screws and washers at the rate 2 of 5 dowels per m. Use min. 20 mm boards. - Cover all joints with fiber glass tape embedded in flexible tile adhesive. 8

Uneven walls Procedure - Drill the board at the rate of 5 dowels per2 m (min. 20 mm thick). - Place dabs of adhesive to be placed on the holes, then the board to be offered up and aligned vertically and horizontally. - Once the adhesive dries, drill the board through the holes and the wall, and insert dowels, washers and screws, hammer the washer with rubber malt to finish level with board surface. Tape all the joints and apply flexible tile adhesive in the usual manner, and when the adhesive dries, the wall can be tiled. Marmox Board on floors Marmox Board can be used as a structural element in floors with the option of 6 mm or 10 mm. Being practically waterproof, it is ideal for use in bathrooms and showers. However, the concrete floor must be level and dust free. New concrete should be cured before fixing Marmox Board 9

Marmox construction boards Concrete floors Procedure: - All traces of existing material should be removed to the concrete substrate; the floor should be level and dust free. - New concrete slab should be cured before fixing Marmox Construction Boards. - Apply a bed of flexible adhesive to the concrete slab with a notched trowel; boards are then to be thoroughly bedded in a staggered pattern, ensuring that no voids remain beneath them. - When the tile adhesive is cured, tape all the joints with the fiber glass tape, then install the heating element, and tile with flexible tile adhesive. - Movement joints must not be bridged by the Marmox construction board. MARMOX CONSTRUCTION BOARDS Timber floors Procedure: - Timber floor must be rigid, checked for flatness. - The floor must be primed, before fully dry apply flexible cement adhesive layer with notched trowel, boards then laid (min. 10 mm) in a staggered pattern, fully bedded to ensure no void under the boards. - When the adhesive is cured, apply fiber glass tape to the joints and flexible tile adhesive. - After flexible tile adhesive dries secure the boards with screws and washers at the rate of 15/board with min. 30 mm from the edge. 10

1.2 Marmox Jagged Boards Marmox Jagged Boards are prefabricated curved boards that have countless applications in the building industry. These boards are precut either in the longitudinal or transverse directions. They are especially useful in bathroom constructions and apart from having aesthetic values they are proven time savers. Marmox Jagged boards are ideal to form curvings around bath tubs and cladding around columns. It can be used in conjunction with all Marmox fixing accessories. All joints between boards must be reinforced with fiberglass tape and a layer of waterproof tile adhesive Technical Data Reference Thickness Width Length Direction of the groove JAG L 250 JAG W 250 20 or 30 600 2500 Longitudinal transversal 11

Marmox construction boards 1.3 Angle Boards MARMOX CONSTRUCTION BOARDS Dimensions Reference Thickness Dimensions Length 20 ANG 150 150x150 20 ANG 200 200x200 20 2500 20 ANG 300 300x300 20 ANG 400 400x200 12

1.4 Marmox CS1: Impact sound insulation boards Marmox CS1 Board differs from standard Marmox Board in that it is covered with a layer of rubber foam that provides high impact insulation properties. The panels are available in two versions: Marmox CS1 which is covered with one rubber layer on only one side, while CS2 is covered with two layers of rubber, one on each side to further improve impact properties. (testing reports are available upon request). Marmox CS1 construction board Rubber foam Cement slurry Fiber glass mesh XPS foam Fiber glass mesh Cement slurry 13

Marmox construction boards 1.5 Marmox XT: Phenolic Foams Marmox XT differs from standard Marmox Board in that the core material is made of a specially selected type of phenolic foam instead of XPS. The main advantages of Marmox Board XT in comparison to the XPS type are the considerably better heat insulation values, the non-combustible fire safety and higher continuous working temperatures (more than double) and the considerably higher resistance to fire and high temperatures. On the other hand, the XPS type usually has lower water absorption properties. However, Marmox Board XT has comparable water absorption when using an additional surface waterproofing. MARMOX CONSTRUCTION BOARDS Cement slurry Fiber glass mesh Phenolic foam Fiber glass mesh Cement slurry The comparison list between the main properties of Marmox Board (XPS) and Marmox Board XT is as follows: Properties Product Test Marmox XT Marmox XPS Weight (t/m 2 ) Thermal conductivity of foam BS 4370 Refer to MB table 0.02-0.025 W/mK Nearly similar 0.028-0.035 W/mK Compressive strength at 10% deflection 3 kg/cm 2 3 kg/cm 2 Fire safety Non - combustible Self extinguishing Fire test classification BS 476 part 6&7 Class 0 Class 0 Max. Continuous working temp. 150 o C 70 o C Reference Thickness 4 XT 125 4 6 XT 125 6 10 XT 250 10 12.5 XT 250 12.5 20 XT 250 20 30 XT 250 30 40 XT 250 40 50 XT 250 50 80 XT 250 80 Width 600 Length 1250 2500 14

1.6 Marmox HD: Heavy duty, high strength, non-compressible type Marmox HD boards differ from standard construction boards in that they are strengthened with regularly distributed polymeric concrete prisms passing through the total thickness of the board. The diameter of the prisms range between 10 to 30mm. They are spaced at distances of 25 to 100mm in both directions. The main advantage of the Marmox HD board is its high compressive strength which varies 2 between 4 and 24 Kg / cm at a negligible compressibility compared to the standard Marmox board. Compared to the standard type, Marmox board HD doesn't show a significant decrease in heat insulation or weight increase. Type *1 Comp. strength (kg/cm 2 ) K-value (W/mK) Thickness Length Width Marmox Board HD 30 HD 40 4 0.036 30 HD 80 8 0.038 30 HD 120 12 0.04 30 HD 240 24 0.042 Standard Marmox Board 3 kg/cm 2 at 10% deflection 0.032 30* 2 1250* 2 600* 2 *1 *2 With negligible deflection Other dimensions are available upon request 15

Marmox construction boards 1.7 Marmox VP1 Boards with vapor proofing properties Marmox Boards VP1 are made of extruded polystyrene foam boards, covered on one side with special cementitious mortar, reinforced with alkali resistance glass fiber mesh and on the other side with aluminum foil glued with special epoxy material. The surface of the aluminum foil is coated with epoxy resin and fine quartz sand to ensure a good adhesion to tile adhesives. Sand Fiber glass mesh Epoxy Aluminum sheet Epoxy XPS foam Fibe glass mesh Cement slurry MARMOX CONSTRUCTION BOARDS The extruded polystyrene foam boards are HCFC free. The boards are tough, lightweight and water resistant. The surface is ready for tiling. The main advantage of Marmox Board VP1 is the extraordinary water vapor proofing properties. The boards are suitable for use as a substrate for tiles in wet areas and very humid rooms. The boards are water impermeable and heat insulating. They are very easy to use and simple to install. S dvalue = about 300 M Fields of applications Marmox board VP1 is specially made for applications in wet areas and very humid rooms. Characteristics _ Marmox board VP1 load bearing is 30 tons/m 2 (at 10% deflection) _ Marmox board VP1 can be easily cut to size _ Marmox board VP1 is water impermeable _ Marmox board VP1 is an excellent vapor and damp barrier 16

1.8 Marmox Board cladding of bath tubs: Marmox bath boards are standard panels of 3 cm thickness and different sizes to fit all situations. The boards are ideal to fit any length of baths. Marmox bath boards are also available with height adjustable feet. Marmox also offers a unique format of 55 cm and 185 cm long, to fit most bath tubs. Thanks to Marmox Boards, cladding a bath tub has now become very easy and quick for everyone. - Measure the 2 sides of the bath tub to be cladded, use a hand saw, a knife or a cutter to cut the boards to suit. - Fix two WB brackets on the sides of the panels to be fixed to the wall and to the bottom of the panels on the floor, then apply silicone sealant on all the edges of the panels. - Use a pair of PB brackets to hold the two panels together. - Apply a fiberglass tape to all the joints and coat it with flexible tile adhesive, after drying it is ready for tiling. 17

Marmox construction boards Illustration for the steps to install Marmox Board cladding of bath tubs MARMOX CONSTRUCTION BOARDS Available in many sizes including 185 x 55 x 3 cm Illustration for the steps to adjust the height adjustable feet Table of references Reference Type Thickness Length Width 30 MB 185 without jacks 1850 30 TAB 180 1800 30 30 TAB 220 with jacks 2200 30 TAB 260 2600 550 600 18

1.9 Marmox VBR boards Properties: MARMOX Board VBR are made of extruded polystyrene foam boards, covered on both sides with special cementitious mortar, reinforced with alkali resistant glass fiber mesh. The extruded polystyrene foam boards are HCFC free sliced at specific distances to provide the wished water vapor breathable property. The boards are tough, lightweight and flame and water resistant. The main advantage of MARMOX Board VBR is the extraordinary water vapor breathable properties. The boards are also suitable for use as outside insulating cladding of buildings. They are very easy to use and simple to install. The structure of the board allows it to be cut easily by saw or knife, and to be nailed or screwed directly onto most surfaces. S Value = about 1.6 m. at 50 mm thickness DIN 12086 (lower value upon request) d Applications MARMOX BoardVBR is especially suitable for facade insulation of buildings. Advantages 2 MARMOX Board VBR load bearing 30 tons/m (at 10 % deflection) MARMOX Board VBR can be easily cut to size MARMOX Board VBR is water resistant MARMOX Board VBR is excellent water vapor permeable. Cement slurry Fiber glass mesh XPS strips Fiber glass mesh Cement slurry Marmox VBR 19

Dimensions of Marmox VBR boards (1) Marmox construction boards Reference Thickness Width Lenght Weight (kg/board) U-value (W/m 2 K) 30 FI 250 30 5.3 1 40 FI 250 40 600 2500 5.9 0.7 50 FI 250 50 6.5 0.57 (1)Other dimensions are available upon request Properties of XPS foam - Blowing agent: HCFC - free in accordance with European regulations. 3 - Density: 36 (±5%) kg/m (DIN 53420). 2 - Compressive strength: 0.3 N/mm (at 10 % deflection, DIN 53421) 6 - Expansion coefficient: 70 x 10 - Fire resistance: class E (DIN EN 13 501). o o - Temperature Range: - 50 C to + 75 C - Thermal Conductivity: 0.032 W/(mK) (DlN 52612). MARMOX CONSTRUCTION BOARDS VBR boards can be easily installed in few easy steps: 20

1.10 Marmox Multi - Size Toilet Box Marmox multi - size toilet box is a universal ready to tile toilet box that can be cut easily to the wished size. 120 100 32 Reference Item Width (cm) Lenght (cm) Depth (cm) 120 TB 100 Toilet box 100 120 32 21

Marmox construction boards 1.11 Under-floor heating 40% of under-floor heating gets lost through floors. Marmox Board help minimize heat loss through the floor and will dramatically reduce heating costs, they are therefore ideal for use with under-tile heating systems. By using Marmox Board in conjunction with underfloor heating, a warm floor can be achieved in as little as 20 minutes compared to several hours if they are not used. Marmox boards are recommended by most leading under-floor heating manufacturers. MARMOX CONSTRUCTION BOARDS Installing Marmox Board under-floor heating insulation Whatever the construction of your subfloor, our under-floor heating insulation will be sure work with it. The system can be installed on both concrete and timber floors. Fixed with adhesive Procedure: - Make sure the floor is clean and dirt free. - Using a floor trowel comb a thick bed of cement based flexible tile adhesive over the floor. - Lay Marmox Board down in place and press firmly. Stagger all the joints in a brick like fashion. Tape the joints with Marmox reinforcing tape. For extra waterproofing you can use Marmox acrylic sealant over or between the joints. Or for really wet areas use Marmox self-adhesive waterproof tape. - The under-floor heating system can then be simply rolled out and fixed according to the manufacturer's recommendations and is then ready for tiling. 22

Fixing with screws and washers Procedure: - Make sure the floor is clean and dirt free. - Use 12 stainless steel screws / Marmox washers per 1.25 m board (3 rows or 4). Secure the Marmox Boards tightly to the floor, ideally in a brick like fashion. - Tape the joints with Marmox reinforcing tape. For extra water proofing you can use Marmox acrylic sealant over or between the joints and over screw holes. For really wet areas use Marmox self-adhesive waterproof tape. 23

ACCESSORIES ACCESSORIES < Mounting accessories for ready - to - tile solutions > 50

Accessories Photo Ref Description Packing Reinforcing fiberglass tape 25 meter x 10 cm ACC001 Used to reinforce the joints between boards and should be used in conjunction 1 with a waterproof tile adhesive. Sealing tape 10 meters x 12.5 cm linear ACC002 Used to seal the systems of recipients, this band is equipped with an elastomer layer and a layer of polyester mesh to allow good joint and a perfect 1 seal. Corners sealing ACC003 These corners will allow you to easily seal your system 1 ACC004 Metal or plastic connectors and screws To strengthen the anchorages and connections between boards 20 Wall brackets The wall brackets are used for connecting the boards to the wall / floor. The ACC005 brackets are applied firmly into the surface of the boards and is then put 2 into position to screw in the wall / floor through the brackets. Perpendicular brackets Brackets that are used to set perpendicular two perpendicular boards while ACC006 the glue dries. The brackets are applied firmly into the surface of each 2 board, after applying a bed of silicone / PU on each side of the board Joints brackets ACC007 Brackets that are used to connect two boards together online. The brackets are applied to joints in the foam of the two boards after applying 2 a silicone or PU between the two boards Waterproof mortar ACC008 This waterproof tile adhesive cement base is supplied in bags of 5 kgs and 1 allows you to paste and seal boards and receivers. Self adhesive tape - 10 meters long ACC009 This product is equivalent to the conventional sealing tape, but is equipped 1 with an under layer of butyl to provide self adhesion to substrates. PU Adhesive Sealant Cartridge ACC010 This mastic adhesive bonding will guarantee a solid, fast and perfect sealing 12 between the boards. Slope piece 150 cm x 90 cm x 8 cm Slope piece is now a priority and although the italian showers respond very well to access to the disabled, the bathroom renovation do not always offer the possibility of having a shower in the floor. Marmox proposes a slope piece ready-to-tile in a standard size. ACC011 1 Thickness: up to 8 cm / Length: 1.5 m / Width: 0.90 meters Can be cut to desired size and height, the slope piece that is ready to tile will provide an aesthetic accessibility to all shower underlays, while maintaining consistency in the bathroom on the ground Sealing wall fleece The Marmox sealing wall fleece is designed from a polyester layer and a layer of thermoplastic elastomer. This fleece is ready-to-tile and will achieve ACC012 a minimum thickness (300 g / m or about 1 mm thick), a perfect seal walls in the bathroom. The dimensions of the mat (length: 2.50 m width x 0.95) 1 allows to seal a record to a height greater than one meter Raising system in extruded polystyrene ACC013 Available in the size of 120/120cm, Marmox raising systems are boards of extruded polystyrene 8 cm thick, with a central hole. It is specially innovated 1 to enhance an installation of a shower underlay. 51