00 Typical ventilated facade installation mounted with top hat channels onto external walls, awning soffit and fascia. 00 Wall panels are shown in varying heights, having open joints for ventilation of the cavity which is open along the full extent of bottom and top edges. 00 00 Important: Parklex panels incorporate a balancing timber veneer to the back of the panel in order to balance the differential in expension rates between core and facing materials, thereby eliminating buckling of panels under changes in atmospheric conditions. However, buckling of panels may still occur if Parklex is installed incorrectly with differing exposure between front and rear faces of panels. Therefore, Parklex must be installed with a fully ventilated cavity as depicted in these drawings or an equivalent system, such that temperature, humidty and air movement are equalised between both faces of panels. A ventilated cavity also aids in the control of moisture and heat through the external building envelope. 00 00 typical section :0
00 00 00 00 00 00 00 00 00. mm thick panel fixed to top hat with mm wide x.mm thick M VHB continuous adhesive tape.. 0mm wide open joints between panels.. Line of floors and ceiling behind.. Bottom edge of wall panels (behind awning fascia).. Indicative window. typical elevation :0 - conceal fixed with M tape dwg no. parklex-00/
00 00 00 00 00 00 00 00 00. mm thick panel fixed to top hat with mm wide x.mm thick M VHB continuous adhesive tape...... 0mm wide x mm deep x.mm bmt top hat channels fixed vertically at maximum 0mm centres. 0-0mm long x mm deep spacer top masonry wall, spaced 00mm at ends and maximum 00mm intermediate centres. 0mm wide joint (not filled or backed). Line of floors and ceiling behind Bottom edge of wall panels (behind awning fascia). Indicative window. typical elevation :0 showing support framings - conceal fixed with M tape dwg no. parklex-00/
. mm thick panel fixed to top hat with mm wide x.mm thick M VHB continuous adhesive tape... 0mm wide x mm deep x.mm bmt top hat channels fixed vertically, spaced at maximum 0mm centres. 00-00mm long x mm deep spacer top masonry wall, at 00mm maximum centres.. Impermeable non-reflective sarking lapped 0mm at joints, sealed at joints and perimeter with continuous bead of Sikaflex Pro... 0mm wide joint (not filled or backed).. Indicative metal sheet parapet cladding.. Indicative flashing.. 0. Indicative wall/ parapet framing. Indicative box gutter.. Indicative roofing.. Indicative structural steel.. Indicative substrate walls.. Indicative internal ceiling and wall linings. 0 typical section detail : parapet wall - conceal fixed with M tape dwg no. parklex-00/
0 0 typical jamb detail : typical head detail :. mm thick panel fixed to top hat with mm wide x.mm thick M VHB continuous adhesive tape.. 0mm wide x mm deep x.mm bmt top hat channels fixed vertically, spaced at maximum 0mm centres. 0. 00-00mm long x mm deep spacer top masonry wall, at 00mm maximum centres.. Impermeable non-reflective sarking lapped 0mm at joints, sealed at joints and perimeter with continuous bead of Sikaflex Pro.... 0mm wide joint (not filled or backed). Flashing.. Caulking.. Indicative wall framing. 0. Indicative window.. Indicative window sill... Indicative sill board. Indicative substrate walls.. Indicative internal ceiling and wall linings. typical sill detail : - conceal fixed with M tape dwg no. parklex-00/
..... mm thick panel fixed to top hat with mm wide x.mm thick M VHB continuous adhesive tape. 0mm wide x mm deep x.mm bmt top hat channels fixed vertically, spaced at maximum 0mm centres. 00-00mm long x mm deep spacer top masonry wall, at 00mm maximum centres. Impermeable non-reflective sarking lapped 0mm at joints, sealed at joints and perimeter with continuous bead Sikaflex Pro... 0mm wide joint (not filled or backed). Flashing.. Caulking.. Indicative wall framing. 0.. Indicative concrete edge beam. Indicative wall substrate.. Indicative internal ceiling and wall linings. 0 - conceal fixed with M tape typical section detail : dwg no. parklex-00/
... mm thick panel fixed to top hat with mm wide x.mm thick M VHB continuous adhesive tape. 0mm wide x mm deep x.mm bmt top hat channels fixed vertically, spaced at maximum 0mm centres. 00-00mm long x mm deep spacer top hat or block fixed through sarking and backing sheet to plate, nogging or girt (provide masonry wall, spaced at 00mm maximum centres... Impermeable non-reflective sarking lapped 0mm at joints, sealed at joints and and perimeter with continuous bead Sikaflex Pro... 0mm wide joint (not filled or backed). Flashing.. Indicative wall framing.. Indicative substrate wall. 0. Indicative concrete edge beam... Indicative internal ceiling and wall linings. Indicative box gutter.. Indicative structural steel.. Indicative roofing.. Indicative concealed grid ceiling suspension system. typical section detail : awning gutter - conceal fixed with M tape dwg no. parklex-00/
. mm thick panel fixed to top hat with mm wide x.mm thick M VHB continuous adhesive tape.. 0mm wide x mm deep x.mm bmt top hat channels fixed vertically, spaced at maximum 0mm centres.. 00-00mm long x mm deep spacer top hat or block fixed through sarking and backing sheet to plate, nogging or girt (provide masonry wall, spaced at 00mm maximum centres.. Impermeable non-reflective sarking lapped 0mm at joints, sealed at joints and and perimeter with continuous bead Sikaflex Pro... 0mm wide joint (not filled or backed).. Flashing.. Indicative roofing.. Indicative structural steel. 0. Indicative fascia framing.. Indicative concealed grid ceiling suspension system.. Indicative roof purlin. 0 typical section detail : awning fascia - conceal fixed with M tape dwg no. parklex-00/
typical plan detail :.. mm thick panel fixed to top hat with mm wide x.mm thick M VHB continuous adhesive tape. 0mm wide x mm deep x.mm bmt top hat channels fixed vertically, spaced at maximum 0mm centres.. 00-00mm long x mm deep spacer top masonry wall, at 00mm maximum centres.. Impermeable non-reflective sarking lapped 0mm at joints, sealed at joints and perimeter with continuous bead of Sikaflex Pro. typical plan detail :.. Hardi-flex fibre cement sheet (to framed up walls). 0mm wide joint (not filled or backed).. Indicative wall framing/ substrate. typical plan detail : - conceal fixed with M tape dwg no. parklex-00/