ACCESSIBLE SHOWERING SOLUTIONS Easa Technical Collection Wet Room Easa Dek
85% Wet Room Easa Dek A Resilient, easy to install floor former or base concept and a Universal Design alternative to building waterproof wet floors with the added benefit of cut to size. 150mm 150mm 85% Only 22mm thick. Our unique patented floor former is lightweight for a single installer and focuses on strength and multi-functionality (patent GB2469662A). Suitable for vinyl or tiled flooring. Can be installed in a corner or an alcove. Tiling Upstands can be supplied to provide enhanced waterproofing protection. Non-handed. Can be cut if required (cut edges must be fitted against the walls). Available in 7 different sizes. Weight capacity 380 kg / 60 stone (Bariatric). Offset waste location to help avoid joists. Wastes for vinyl or tiles are provided to suit the required floor type. Easa recommends fitting waterproof tanking kits for installations with tiles. 100% recyclable. All Easa Deks can be cut in length and width. Please ensure all cut edges are fitted against the walls. Can be cut within 150mm of waste centre point. RECYCLABLE PRODUCTS 380 kg 60 stone Designed and Made in the UK We recommend not to cut more than 85% as the next smaller standard size would then be a better choice. Example: Cutting 85% of the Dek1050 would be 892.5 which is slightly less than our standard Dek900.
PRODUCT CODE DESCRIPTION (mm) SIZE (mm) SHOWER AREA (mm) WASTE TO LONG SIDE (mm) WASTE TO SHORT SIDE (mm) MINIMUM CUT TO SIZE LENGTH (mm) MINIMUM CUT TO SIZE WIDTH (mm) 900900 105000 122122 130080 140090 150080 170075 900 x 900 1050 x 1050 1220 x 1220 1300 x 800 1400 x 900 1500 x 800 1700 x 750 900 x 900 1050 x 1050 1220 x 1220 1300 x 800 1400 x 900 1500 x 800 1700 x 750 850 x 850 1000 x 1000 1170 x 1170 1250 x 750 1350 x 850 1450 x 750 1650 x 700 317 392 477 517 567 617 717 317 392 477 267 317 267 242 765 895 1035 1105 1190 1275 1445 765 895 1035 680 765 680 640 All Easa Dek floor formers can be supplied with discrete tiling upstands. If Easa Dek floor former is installed in an alcove, please request an additional tiling upstand to complete the installation. Easa Dek floor formers can be cut. Cut edge(s) must be fitted against the wall(s). Easa Dek Characteristics 317mm 517mm 900 x 900 317mm 1300 x 800 267mm 900mm 800mm 900mm 567mm 1300mm 1050 x 1050 392mm 392mm 1400 x 900 317mm 900mm 1050mm 1400mm 617mm 1050mm 1500 x 800 267mm 800mm 477mm 1220 x 1220 477mm 1500mm 1220mm 1700 x 750 242mm 717mm 750mm 1220mm 1700mm TRAY RAMPED EDGE SUITABLE FOR FLOOR TYPES HANDED ALCOVE WEIGHT CAPACITY CUT TO SIZE Easa Dek Barrier Free (0mm) Wood No Yes 380 kg 60 stone Yes - see table above Screed
Easa Dek Fitting Instructions for Solid Floors Depending on the size, the Floor Former may be heavy, please be careful whilst handling. Protect shower base from damage by using the cardboard packaging. Please note that the floor former must not be fitted without a floor covering applied on top, e.g. sheet vinyl flooring, tiles, etc. All of the Easa Dek range of Floor Formers can be cut to size using a conventional hacksaw or stone blade grinder. However it is important that any cut edges are placed to the wall. It is not possible to place any cut edges to the outside edges where the floor former meets the floor. Floor Former can be cut to size using a conventional hacksaw or stone blade grinder. Cut edges MUST be placed against a wall. 1. Place Floor Former in position and mark out the size on the floor. 2. Break out screed or concrete to a minimum depth of 25mm. Check that the Floor Former fits into the opening. 3. Decide on direction of waste and breakout wall if required. For the waste it is necessary to break out 150mm diameter to a depth of 150mm. Repair any damage to damp proof course membrane. Install the waste piping (minimum fall 1 in 40). It should line up with the centre of the waste opening in the Floor Former. Please read the separate waste instructions. 4. Add support under the Floor Former by laying a weak concrete mix in excavated area. Easa UK & Ireland - Tel: +44 (0) 28 9261 2500 Fax: +44 (0) 28 9261 2326 Email: info@easagroup.com Website: www.easagroup.co.uk
Easa Dek Fitting Instructions for Solid Floors To ensure a waterproof seal a tiling upstand may be added to the edges of the floor former that will be placed against the walls. Optional rigid aluminium or flexible EPDM upstands are available. 5. Place the Floor Former gently into position do not drop as this could cause damage. 6. Ensure Floor Former is level on all sides. 7. When the waste is seated in position, use a 3.5mm drill bit to bore through the 4 location holes of the waste flange into the floor former. Be careful not to go too deep as the waste pipe is underneath. Fit self tapping screws provided to secure the waste into place. 8. The seam between floor and Floor Former must be completely level. Fill any gaps with polyester filler paste. For tile floor installations you will need to apply the Easa tanking system as per kit instructions. Please Note: Apply sheet flooring or tiles as required using appropriate adhesive. The correct waste must be used depending on flooring type see separate waste instructions for fitting waste to appropriate flooring type. Easa UK & Ireland - Tel: +44 (0) 28 9261 2500 Fax: +44 (0) 28 9261 2326 Email: info@easagroup.com Website: www.easagroup.co.uk
EASA Fitting Instructions for Wooden Floors Depending on the size, the Floor Former may be heavy, please be careful whilst handling. Protect shower base from damage by using the cardboard packaging. Please note that the floor former must not be fitted without a floor covering applied on top, e.g. sheet vinyl flooring, tiles, etc. All of the Easa Dek range of Floor Formers can be cut to size using a conventional hacksaw or stone blade grinder. However it is important that any cut edges are placed to the wall. It is not possible to place any cut edges to the outside edges where the floor former meets the floor. Floor Former can be cut to size using a conventional hacksaw or stone blade grinder. Cut edges MUST be placed against a wall. 1. Place Floor Former in position and mark out the size on the floor. 2. Cut out floor sheeting or floor boards and check that the floor former fits into the opening. 3. Floor Former should be rotated so that the waste does not interfere with joists. 4. Decide on direction of waste outlet pipe and breakout wall as required install the waste piping (minimum fall 1 in 40), it should line up with the centre of the waste opening in the Floor Former. Please read the separate waste instructions. CROSS SECTION VIEW 5. Standard Method - At each end of the Floor Former add purlins between the joists, then add additional purlins at 400mm intervals. 6. Joists and purlins must be level on all sides. Easa UK & Ireland - Tel: +44 (0) 28 9261 2500 Fax: +44 (0) 28 9261 2326 Email: info@easagroup.com Website: www.easagroup.co.uk
EASA Fitting Instructions for Wooden Floors CROSS SECTION VIEW 7. Heavy duty method - At each end of Floor Former add purlins between joists. Then add battens to the sides of the joists and form a platform with 18mm plywood level with the top of the joists. 8. Joists and plywood must be level on all sides. To ensure a waterproof seal a tiling upstand may be added to the edges of the floor former that will be placed against the walls. Optional rigid aluminium or flexible EPDM upstands are available. 9. Place the Floor Former gently into position do not drop as this could cause damage. Polyurethane expanding foam or silicone can be added underneath the floor former as necessary. 10. Ensure the Floor Former is level on all sides. 11. When placing the Floor Former into position ensure the waste fits neatly onto the shower outlet pipe. When the waste is seated in position, use a 3.5mm drill bit to bore through the 4 location holes of the waste flange into the floor former. Be careful not to go too deep as the waste pipe is underneath. Fit self tapping screws provided to secure the waste into place. Do not over-tighten the screws. FILLER 12. Mark position of the joists and drill all four sides of the Floor Former into the joists and purlins. The holes must be countersunk to accommodate the screw heads (4.2mm x 60mm recommended screw size). 13. The seam between floor and Floor Former must be completely level. Fill any gaps with polyester filler paste. If required apply tanking system as per manufacturers instructions. Please Note: Apply sheet flooring or tiles as required using appropriate adhesive. The correct waste (or adaptor) must be used depending on flooring type see separate waste instructions for fitting waste to appropriate flooring type. Easa UK & Ireland - Tel: +44 (0) 28 9261 2500 Fax: +44 (0) 28 9261 2326 Email: info@easagroup.com Website: www.easagroup.co.uk
Wastes and Traps Wet Room Easa Dek Wastes Vinyl Floor Vinyl Floor Tiled Floor Tiled Floor Plastic Vinyl Waste, available in standard, low profile or pump versions. Stainless Steel Vinyl Waste, available in standard, low profile or pump versions. Plastic Tiling Waste, available in standard, low profile or pump versions. Stainless Steel Tiling Waste, available in standard, low profile or pump versions. Wet Room Waste Plastic Vinyl Max. flow rate 24 litres per minute. (19mm water seal trap) Wet Room Low Profile Waste Max. flow rate 46 litres per minute. (50mm water seal trap) Two Piece ½ ½ Wet Room Waste S/Steel Vinyl & All Tiled Floor Max. flow rate 24 litres per minute. (19mm water seal trap) Wet Room Pump Waste Max. flow rate determined by pump. (Untrapped) ½ EASA Product Code VW1R VS1R WT1R ST1R LPWV LPVS LPWT LPST PWWV PWVS PWWT PWST Description Vinyl White Plastic Standard Waste Vinyl Stainless Steel Standard Waste Tiling White Plastic Standard Waste Tiling Stainless Steel Standard Waste Vinyl White Plastic Low Profile Waste Vinyl Stainless Steel Low Profile Waste Tiling White Plastic Low Profile Waste Tiling Stainless Steel Low Profile Waste Vinyl White Plastic Pump Waste Vinyl Stainless Steel Pump Waste Tiling White Plastic Pump Waste Tiling Stainless Steel Pump Waste Size (visible) 140mm diam. 140mm diam. 150x150mm 150x150mm 140mm diam. 140mm diam. 150x150mm 150x150mm 140mm diam. 140mm diam. 150x150mm 150x150mm Dek Wastes are necessary in order to complete a Wet Room Easa Dek installation. Please order the waste that meets your floor requirements.
Easa Dek Technical Highlights WET ROOM EASA Wet Floor Former is installed below the fl oor covering (vinyl or tiles). Waste below fl oor. Barrier Free (0mm) All our Wet Room Easa Dek fl oor formers will withstand 380 kg / 60 Stone when installed as per our instructions. RECYCLABLE PRODUCTS The Wet Room Easa Dek is fully recyclable. When you buy environmentally friendly products such as our fully recyclable shower trays, fl oor formers and doors, you help reduce waste by creating a market for our recycled materials. You also help create jobs in businesses that handle and use recycled materials. Purchasing green products is like making a vote. Requesting more sustainable products in the market place tells manufacturers that consumers care about the way products are made. Installation Overview WET ROOM EASA The Easa Dek system rests beneath the chosen fl oor covering (tiles or vinyl), the unique design focuses on strength, multi-functionality and speed of installation. Ensure silicone sealant is applied between the top edge of tiling lip and wall to provide a watertight seal and effectively fi ll any gaps between fl oor and leading edges. The fl oor former will be covered with the chosen fl oor covering to create a complete barrier free access. WET ROOMS A waterproof tanking system is essential to ensure a waterproof installation of the Easa Dek.
Information and cleaning instructions for your Wet Room Easa Dek Please read the following information carefully Product description of Easa Deks The Easa Dek floor former is manufactured from Glass Reinforced Plastic (GRP) and can withstand up to 380 kg. All Easa Deks can be fitted on both screed and wooden floors and full fitting instructions are supplied containing instructions of the Easa Dek. You are advised to keep these instructions for your information. The dimensions of the shower system will be detailed on the warranty card. Safety first For your safety, it is advisable to be seated in the showering area before turning the water on. Ensure shower doors and curtains are closed. For clients who are mobile, it is advisable to use grab rails to assist with transfers in and out of the showering area. Clients using wheeled shower access may require assistance for positioning and transferring in and out of the showering area. Always apply any shower chair brakes during showering. After showering, allow the excess water to drain away before standing or transferring out of the shower area. Care should be taken when transferring in and around the shower area as wet surfaces greatly increase the risk of slipping. The waste supplied can have the internal section removed for easy cleaning, and allows water to drain effectively from a showerhead that delivers a maximum of 24 litres per minute (low profile wet-room wastes 46 litres per minute). Wet Room Easa Dek floor formers Our Easa Dek floor former will be covered with anti-slip floor covering and it is important to follow the manufacturers cleaning instruction for that specific floor covering. This may be available from the installer. Cleaning instructions / maintenance DO NOT USE: Abrasive Cleaners Hair Colorants Bleach Do not pour any chemical drain cleaner down the waste Waste maintenance Remove the top grid by lifting it straight up and then the internal tube by turning it anti-clockwise. Remove any hair and debris, flush through with clean water and replace back in position. WARNING Concentrated cleaning liquids, shampoos, conditioners, soaps etc that are left on the Easa Dek greatly increases the risk of slipping. If a family member, care worker, home help or privately employed cleaner is responsible for the cleaning of the Easa Dek please encourage them to read these instructions. Warranty* All our Easa Deks are manufactured to the highest standard and have a lifetime warranty. If the unit fails, contact us, quote the serial number that appears on the warranty card and follow the advice detailed in Customer Complaints Procedure. We will either repair or replace the unit within 14 working days if found to be defective. Please note Claims will not be met under guarantee if the product has been abused in any way by neglect, improper use or failure to maintain in accordance with Easa s recommendations, or if the system has been damaged in any accident. The company, when assessing a warranty claim, will also consider abnormal wear and tear. * Please see our Terms and Conditions for full details.
Our Quality, Safety & Design Assurance CE European Union Certificates of Conformity Easa products have been extensively tested and comply with the following British & European Standards: BS EN 14527:2006 (E) Shower Trays BS EN 14428:2004 (E) Shower Enclosures/Doors EU Construction Product Directive (89/106/EC) BS EN 12600:2002 Glass in building. Pendulum test. Impact test method and classification for flat glass BS EN 274-1:2002 Waste fittings EASA W A R R A N T Y Easa Warranties* Easa offers a Lifetime Warranty against manufacturing and material defects, excluding normal wear and tear in general domestic applications. Accessories have a 2 year warranty. * Please see our Terms and Conditions for full details. 2 YEAR WARRANTY ON ALL ACCESSORIES 3D Design and Survey Service Upon request an experienced Easa sales representative can discuss your needs and requirements, and draw a 3D design layout of the bathroom, and provide product technical advice. Recyclability RECYCLABLE PRODUCTS Easa Deks are fully recyclable. When you buy environmentally friendly products such as our fully recyclable shower trays and floor formers, you help reduce waste by creating a market for our recycled materials. You also help create jobs in businesses that handle and use recycled materials. Purchasing green products is like making a vote. Requesting more sustainable products in the market place tells manufacturers that consumers care about the way products are made.
Products in the Evolution Range: The Evolution Collection Shower Doors An exclusive range of functional and safe systems designed specifi cally for all family members regardless of age or ability The Evolution Collection Grab rails Enhancing functionality and Safety Easa N.Ireland (Head Office) Moira Ind Est 34 Old Kilmore Road Moira, Co. Armagh N.Ireland BT67 0LZ Tel: +44 (0) 28 9261 2500 Tel from ROI: 048 9261 2500 Fax: +44 (0) 28 9261 2326 Fax from ROI: 048 9261 2326 Email: info@easagroup.com Web: www.easagroup.com Easa GB (Sub Office) Expressway Works Eastvale Place Yorkhill, Glasgow Scotland G3 8QG Tel: +44 (0) 141 334 2782 BS EN 14527:2006 (E) Shower Trays BS EN 14428:2004 (E) Shower Enclosures/Doors EU Construction Product Directive (89/106/EC) BS EN 12600:2002 Glass in building. Pendulum test. Impact test method and classifi cation for fl at glass. BS EN 274-1:2002 Waste fi ttings Approved code Office of Fair Trading Designed and Made in the UK RECYCLABLE PRODUCTS Copyright 2012 Easa. All rights reserved. TCEDENUK0112