Athletic Complex Renovations Chattahoochee Valley Community College Phenix City, AL BC No.:

Similar documents
MARQUIS Tualatin FIBER-CEMENT SIDING June 15, rev

Section HIGH-TENSION Stretched-Fabric Wall Systems SoftWalls, Inc.

1. This addendum contains the specifications for Acoustical Ceilings: public areas Lobby, Breakfast Room, etc. and not used on all doors.

SECTION GYPSUM BOARD ASSEMBLIES

TABLE OF CONTENTS DIVISION 1 GENERAL REQUIREMENTS

Spec Master 5/7/ For each product requiring color and texture selection, provide full size samples.

A. Meet at Project site <insert number> days before starting installation.

Section Wood Grille Ceiling Panels

DALLAS-FORT WORTH INTERNATIONAL AIRPORT

Division 09 FINISHES TABLE OF CONTENTS

A. Product Data: Submit manufacturer's descriptive literature, and recommendations and instructions for installation.

Geometrik Manufacturing Inc.

SECTION UNIT MASONRY

SYSTEM DETAILS.

Section SoundPly LR M25 Acoustic Ceiling Panels

SECTION ALTERATION PROJECT PROCEDURES

CONTRACT NUMBER: W912DQ-08-C % CORRECTED DESIGN 28 JULY 2008

SECTION ROUGH CARPENTRY. B. AWPA (American Wood Preservers Association) Book of Standards. C. WCLIB (West Coast Lumber Inspection Bureau)

SECTION MISCELLANEOUS METALS THIS SECTION TO BE INCLUDED IN SUB BID FOR SECTION MISCELLANEOUS AND ORNAMENTAL IRON

SECTION ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL

WOOD FLOORING WOOD FLOORING

Banyan Air Service November 18, 2011 AVE Aviation and Commerce Center Building 1 Miami, FL

327 King Street Exterior Repairs & Interior Renovations Project No. H15-N200-PG

Section SoundPly RF M25 Acoustic Wall Panels

TerraClad TM General Specifications

Section Wood Veneer Ceiling Planks Linear

SECTION GYPSUM BOARD

SECTION HANDRAILS AND RAILINGS. A. Section Cast-In-Place Concrete; coordination with substrate.

Corium Brick Rainscreen System Specifications

SECTION IMPACT RESISTANT WALL PROTECTION

Item # 1: Attached are the revised Table of Contents and Specifications added: Section Cabinets and Vanities

ADDENDUM NO. 2 Consisting of 3 pages and Attachments

SECTION ACCORDION FOLDING PARTITIONS

SECTION MANUFACTURED ROOF EXPANSION JOINTS

SECTION DRY-PLACED GRANITE

SECTION AXIOM INDIRECT FIELD LIGHT COVE PERIMETER SYSTEM PART 1 - GENERAL 1.1 RELATED DOCUMENTS

Geometrik Manufacturing Inc.

SECTION (10705) EXTERIOR SUN CONTROL DEVICES

Specifications for FL-100 Soffit Panel

SUBJECT: NEW 2000 INTERNATIONAL RESIDENTIAL CODE (IRC) DATE:

SECTION METAL STAIRS

SECTION ROOF MOUNTED ATTIC EXHAUST VENT

Octaform Quick Liner Wall & Ceiling Panels Guide Specification CAN Page 1

Guide Specifications for Abet Meg External Cladding

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: FIBER CEMENT SIDING REPORT HOLDER: RIEDER FASERBETON ELEMENTE GmbH

SECTION METAL ROOF AND SOFFIT PANELS


Section Wood Veneer Ceiling Tiles Micro Perforated

SECTION PREFORMED CLADDING. A. Part A and DIVISION 1 of PART B are hereby made a part of this SECTION.

Louis Armstrong New Orleans International Airport NOAB Project # North Terminal Development Program Phase 1

SSL-175. Specifications

SECTION CHARRED WOOD [SIDING] [&] [PANELING] GUIDE SPECIFICATION

1. Interior gypsum board. 2. Glass-mat gypsum sheathing board for ceilings and soffits. 3. Cement board. 4. Sound attenuation blankets

DIVISION 5 - STRUCTURAL STEEL AND IRON WORK

SECTION ADDENDA ADDENDUM NUMBER 2

SECTION METAL PLATE CONNECTED WOOD TRUSSES PART 1 - GENERAL 1.01 RELATED DOCUMENTS

SECTION DRYWALL GRID LINEAR LIGHTING INTEGRATION

Marlite Guide Specification 2/24/2017 Surface Systems - MAP375 System SECTION FRAMED DECORATIVE PANEL SYSTEMS PART 1 - GENERAL 1.

Construction Standards PAGE

NOTE TO SPECIFIER: This section is based on the products of Solar Innovations, Inc., which is located at:

SECTION PORTLAND CEMENT PLASTER (STUCCO) WITH ACRYLIC FINISH

Whapmagoostui & Waskaganish Addendum no AR01 August 15, 2017 Cree Daycare Centres Cree Nation Government RRA 1728 Page 1 of 6

Trex Commercial Products page Metal Railing

1. Temperature Change: 120 deg F (67 deg C), ambient; 180 deg F (100 deg C), material surfaces.

SECTION HANDRAILS AND RAILINGS. Display hidden notes to specifier. (Don't know how? Click Here)

PROJECT DIRECTIVE # FOR KALISPELL PUBLIC SCHOOLS

COPYRIGHTED MATERIAL. Contents. 1 Making Buildings 3. 3 Wood Foundations and. Preface to the Sixth Edition xi. Sitework 31

2002 Advanced Building Products, Inc., P.O. Box 98, Springvale, Maine TEL: ; FAX: ; WEBSITE:

Student Services & Classroom Addition

Chevy Chase Club June 30, 2008 Bowie Gridley Architects

Guide Specification for: FABRI TRAK PVC FREE Stretched Fabric Wall System Section [ ] or Section [ ]

Bidders shall acknowledge receipt of this Addendum in writing on his Proposal Form.

Façade Architectural Wall Panel System - Guide Specification 3/11/2017 SECTION FRAMED DECORATIVE PANEL SYSTEMS PART 1 - GENERAL 1.

Preassembled steel stairs with concrete-filled treads.

Framed Decorative Panel Systems

METALS Commissioning of Metals Structural Steel Framing Steel Studs... 2

GENERAL SPECIFICATION FOR FIRE RATED APPLICATIONS

GA APPLICATION OF GYPSUM SHEATHING

FYPON, LLC. February 2014

Slate. Material description

Union County Vocational - Technical Schools Scotch Plains, New Jersey

Store No MAY 13 Addendum No. 1 SECTION ACOUSTICAL PANEL CEILINGS

1. Division 09 Section "Rough Carpentry."

ADDENDUM NO. 1. Bidders are hereby informed that the Construction Plans and/or Specifications are modified as follows:

Powerdek Fleck. SECTION Resilient Athletic Flooring

SECTION GYPSUM BOARD ASSEMBLIES

SERIES STB30 STEEL FIXED THERMAL BREAK DETENTION WINDOWS SECTION 08651

A. This Section includes acoustical panel ceilings installed with exposed suspension systems.

SECTION SLOPED TRANSLUCENT METAL SKYLIGHT SYSTEM

Section PANEL SIGNAGE

.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1.

ADDENDUM NUMBER 1: Portsmouth City Boiler Plant Improvements Project Bid Proposal # Issued: May 23, 2011

LOG COLLEGE MIDDLE SCHOOL

C. Counterflashings at roof-mounted mechanical equipment, vent stacks, curbs, and miscellaneous roof penetrations.

Union County Vocational - Technical Schools Scotch Plains, New Jersey

SECTION COMMERCIAL CURB-MOUNT ACRYLIC DOUBLE DOME SKYLIGHTS

C. Samples: For each door face material, at least 3 by 5 inches (75 by 125 mm) in size, in specified finish.

The following specification refers to the Stepstone, Inc. product known as: Steptreads

SECTION VINYL ACRYLIC CLAD WOOD DOORS PART 1 GENERAL 1.1 RELATED DOCUMENTS

Transcription:

ADDENDUM NO.2 Date: July 27, 2012 blondheim + Mixon, inc. A R C H I T E C T S 2 4 0 Ea st Broad Street P.O. Box One Eufaula, AL 36027 p. 3 3 4. 6 8 7. 8 0 5 7 f. 3 3 4. 6 8 7. 7 9 0 5 Project: Athletic Complex Renovations Chattahoochee Valley Community College Phenix City, AL BC No.: 2012046 Project No.: 12-001 Bidders are hereby notified that the Plans and Specifications are amended as follows by Addendum #2. GENERAL 1. The following manufacturers have been approved, subject to meeting all Specification requirements: Specification Section 04720 Cast Stone Masonry Atlanta West Cast Stone, Inc. 2. Addendum No. 1 New Schedule of Alternates - Alternate No. 3 Add the following: Contractor shall remove existing asphalt and base. New asphalt and base shall be as shown on Sheet C1.04 Asphalt Paving Detail. 3. Addendum No. 1 - Plans Item No. 2 Parking provided by the Owner shall include the concrete walk. 4. Addendum No. 1 Plans Item No. 3 This item changes quantity behind maintenance shed to 18LF. SPECIFICATIONS 1. Specification Section 06100 Rough Carpentry Page 2 of 9, Part 1.4, D, 2: Omit this sentence in its entirety. 2. Specification Section 06190 - Prefabricated Wood Trusses Page 1 of 4, Part 1.4, C: Omit this sentence in its entirety. Addendum No.2 1 of 2

3. Specification Section 06190 - Prefabricated Wood Trusses Page 3 of 4, Part 2.2, C, 3: # 2, Southern Yellow Pine is acceptable. 4. Specification Section 06190 - Prefabricated Wood Trusses Page 3 of 4, Part 2.3, A, 1: Electro-galvanized G60 is acceptable. 5. Specification Section 09513 Acoustical Tile Ceilings Page 3 of 6, Part 2.1, A,1- Ceiling Tiles shall be Classic Fine Textured with Angled Tegular Edge detail as manufactured by Armstrong, or an approved equal. 6. Specification Section 09545 Metal Soffit Panels Omit this section in its entirety and replace with the attached Section 06401- Fiber Cement Board PLANS 1. Sheet A1.02 See attached Supplementary Drawing SDA1.02 for foundation for relocating grand stands. 2. Sheet A2.02 Floor Plans Press Box Floor Plans Stair shown from first floor to second floor is wood construction. 3. Sheet A5.03 Building Section A Home dugout Change metal soffit to read Vented Fiber Cement Board equal to Hardie Vented Soffit. Install at ceiling of dugout and facing over beam. 4. Sheet A5.04 Building Section A Visitors Dugout Change metal soffit to read Vented Fiber Cement Board, equal to Hardi Vented Soffit. Install at ceiling and facing over beam. Building Section B & Detail 3 Change Vented Soffit as above. 5. Sheets M1.01 & M1.02 Air Handling Units 1, 2, and 3 are mounted to the trusses and the weight for each is 60 lbs. 6. Sheet S1.02, Detail 4 Omit this Detail and install steel beams as shown on A5.02 (Section A) and A5.03 (Section A) for lintels at home dugout and visitors dugout. Also Sheet A2.01 Home Dugout First Floor Plan, and Sheet A2.02 Visitors Dugout First Floor Plan. End of Addendum No. 2 Attachments: Specification Section 06401 Supplemental Drawing SDA1.02 Addendum No.2 2 of 2 7/27/2012

SECTION 06401 FIBER-CEMENT BOARD (Vented Soffit) PART 1 GENERAL 1.1 SUMMARY A. Provide exterior architectural woodwork: 1. Standing and running trim. Trim joints in ceiling with ½ x 1 Hardiplank. 2. Miscellaneous trim as indicated on drawings. 1.2 QUALITY ASSURANCE A. Comply with governing codes and regulations. Provide products of acceptable manufacturers, which have been in satisfactory use in similar service for three years. Use experienced installers. Deliver, handle, and store materials in accordance with manufacturer's instructions. B. Standards: Architectural Woodwork Institute (AWI) "Architectural Woodwork Quality Standards." 1.3 PRODUCT HANDLING A. Stack Hardiplank claddings on edge or lay flat on a smooth, level surface. Protect edges and corners from chipping. Store sheets under cover and keep dry prior to installing. 1.4 JOB CONDITIONS A. Nominal 2 inch x 6 inch wood framing selected for minimal shrinkage and complying with local building codes, including the use of weather-resistive barriers and/or vapor barriers where required. Minimum 1½ inch face and straight, true, of uniform dimensions and properly aligned. B. Install weather-resistive barriers and claddings to dry surfaces. C. Repair any punctures or tears in the weather-resistive barrier prior to the installation of the siding. D. Protect siding from other trades. 1.6 WARRANTY A. James Hardie's limited product warranty against manufacturing defects in HardiTrim for 10 years. Section 06401 Page1 of 2

PART 2 - PRODUCTS 2.1 EXTERIOR MATERIALS: HARDIPLANK - JAMES HARDIE BUILDING PRODUCTS, 1-800-9-HARDIE A. Non-asbestos fiber-cement siding to comply with ASTM Standard Specification C1186 Grade II, Type A. B. Soffits to meet the following building code compliance National Evaluation Report No. NER 405 (ICBO).Non-asbestos fiber-cement siding to be noncombustible when tested in accordance with ASTM test method E136. C. Type: Smooth and size as indicated on drawings. (vented) 2.2 FASTENERS A. Fasteners as required and recommended by manufacturer for application. B. Exterior Standing and Running Trim: 1. Back-prime all exterior trim materials prior to installation. 2. Prime all cut ends of exterior trim materials during installation. 3. Grade: Custom. 4. Finish: Paint 5. Color: As selected by architect. PART 3 - EXECUTION 3.1 INSTALLATION A. Provide work to sizes indicated. Install work to comply with quality standards referenced. Back prime work and install plumb, level and straight with tight joints; scribe work to fit. B. Quality Standard: Install woodwork to comply with AWI Section 1700 for the same grade specified for type of woodwork involved. C. Install materials and systems in accordance with manufacturer's instructions. Install materials and systems in proper relation with adjacent construction. Use non-corrosive fasteners for exterior work. Coordinate with work of other sections. D. Comply with manufacturer's requirements for cutting, handling, fastening and working treated materials. E. Repair minor damage, clean and protect. Section 06401 Page2 of 2

ATHLETIC COMPLEX RENOVATIONS CHATTAHOOCHEE VALLEY COMMUNITY COLLEGE PHENIX CITY, ALABAMA 1" = 1'-0" SD A1.02 JULY 27, 2012