ARC FmREGLASS GRATINGS & STAIR TREADS

~ ARC FmREGLASS GRATINGS & STAIR TREADS ARC is an established name in composites and has been providing complete system of FRP gratings for walkways, platfonns, stairs, bridges, grids as tower packing supports, effiucnl lrench cover, swimming pools & other allied usages of moulded and pultruded type gratings, since a dtx:ade. ARC offers system fl exibility to optimise cos!. These are the ideal solution for corrosion problems faced in industrial environments. It forms the right repiacemcni for Sleel or aluminium gratings used in highly corrosive atmosphere. The ARC gratings outlast steel 20 to 1 limes and it is a long term investment, where freq uent grating and walkaway replacement costs are unacceptable. There are 2 types of gratings; Moulded Gratings & Treads Pu ltrudcd Gratings Pultruded and Moulded FRP Grating FEATURES PULTRUDED MOULDED Structure Eccentric Monolithic Monolithic Higher Normal Corrosion Protection Highcr Higher Support Direction Span Side Only Both sides Section Accuracy Good Normal Fire Retardency Good Good UV Protection Good Good Anti Skid Treatment Possible Possible Scope or Construction Limited Flexible G lass Contenl 6()OIo 10 7()OIo 40% 10 50%

Material Options RESrNS Resin Base Resin Code Description Application Orthophthalic OP Moderate corrosion resistance and fire This grating is recommended for use in Polyester Resin retardant, flame spread rating ASTM water/wastewater or air-aging E84 Class 1,25 or less. Operating applications, light industrial temperature - 50"C - 70 "C. applications, and in the wave zone areas of offshore platforms where the environment is moderate. Although OP is the leasl chemical resistant resin, it still offers superior performance to traditional flooring products such as steel, aluminum and wood, and is the most economical resin available. lsophthalic IP Industrial grade corrosion resistance This grating is recommended for use in Polyester Resin and fire retardant, flame spread environments of middle concentration rating ASTM E84 Class 1, 25 or less. inorganic acid, inorganic alkali, etc. OperatinR temperature - 50 C - 105 C. Vinyl Ester Resin VE Superior corrosion resistance and fire This grating is recommended for retardant, flame spread rating ASTM use in environments with serious E84 Class 1,25 or less. Operating corrosion. temperature - 50 C to 110 C. Phenolic resin PH Low smoke and superior fire This grating is recommended resistance, flame spread rating for use in areas where fire ASTM E84 Class I, 5 or less, smoke resistance, low smoke, and low developed index O. Operating toxic fumes are critical. temperature amounting to 180 C. High flame H.FVE Superior corrosion resistance and This grating is recommended for resistant vinyl enhanced fire retardant, flame use in environments with serious ester spread rating ASTM E84 Class I, corrosion requiring better flame 10 or less. Operating temperature resistance. _50 C_110 C. FIBREGLASS In2redienl Specification Property Applicalion E-glass 2400TEX or Excellent soaking ability For environments requiring 4800TEX ensures solid combination high strength and corrosion with resin, thus perfect resistance. physical property and anticorrosion property.

MO ULDED GRATINGS & T READS: ARC moulded fibreglass grating I tread is a siro ng mesh panel which is the chemical resistant flooring choice for many industrial applications. The panels are moulded in one piece, which helps distribute the load to both bearing and cross bars. Continuous fiberglass roving winding in aliemaling layers is thoroughly wetted with resin. When the load is applied to the grating I tread bars, the weight is transferred to adjoining cross bars and bearing bars for even load distribution. The cost- effective panels allow for efficient on-site c utting to minimize grating I tread waste and load bearing bars in both directions allow for use without continuous side suppon. The ARC mo ulded fibreglass grating I tread is sign ificantly lighter in weight than metallic gratings I treads and the high resin content provides long, virtually maintenance-free perfonnance. A higher safety fa ctor is achieved by designing higher glass content at the bottom of the grating / tread for greater tensile strength. The moulded gratings / treads are Corrosion Resistant Fire Retardant: available with Class I fire rating Bidirectional Load Bearing Electronically Transparent: does not affect e lectromagnetic or Radio wave frequency Lightweight Low in Conductivity Low in Maintenance Easy to Install Cost Effective Superior Ergonomics: gives comfort while walking or standing The moulded gratings / treads are made up offibrcglass rovings combined with a choice of various themlosclling resins. All the resins contain a protective UV inhibitor. The gratings / treads have a concave profile on the upper surface, which is skid resistant. However, on request, additionally a slip resistant grilled top surface can also be provided. The grating I tread shall be one-piece construction with the tops of the bearing bars and cross bars in the same plane. Available in green, orange, yellow, black & grey colours.

Accessories for Moulded Gratin gs & Treads a). Angle The ARC pultruded fibreg lass Angle provides a strong, fi rm base for bearing bars. b). Panel Insta llation - Typically all fasteners used, are Stainless Steel 316. The grating! tread fasteners have low profi les, which eliminates rripping hazards. We recommend using at least 8 clips on a panel of size 1000 mm x 3000 mm. Smaller panels must be secured with no fewer than 4 clips. Type M C lips For attaching grating I tread to supports. Type J Cli ps For attaching grating / tread to supports for moderate loads. Type C Clips For joining two unsupported edges if needed.

A\'ailable Moulded Grating Profiles Sq uare Mesh Rectangular Mesh ARC Model Nos. Thickness Mesh Size- Mesh Maximum l\1ax.imum Maximum - T (mm) SxS or Lx.B Pattern Permissible Deflection Recommended (mm) Span (mm) Un iform (mm) Distributed Load (k., m' ) ARC MGS25 25 38 x 38 Square 600 6.35 1020 ARC MGR2S 25 25 x 100 Rectangular 800 9.00 915 ARC MGS38 38 38 x 38 Square 1000 8.63 610 ARC MGSSO 50 50 x 50 Square 1200 8.08 610 ARC MGR38 38 38 x 150 Rectangular 1000 9.30 815 Available Moulded Stair Treads ARC Model Nos. Thickness Mesh Size- Mesh Pattern Maximum Maximum Maximum T (mm) SxS or LxB Permissible Deflection Recommended (mm) Span (mm) Uniform (mm) Distributed Load ".1 m' ) ARC MSTR38 38 38 x 150 Rectan ular 1000 9.30 815

FRP STAIR TREAD COVERS The moulded fibreglass stair tread covers provide an easy. cost-effective way to increase the safety of stairways. The ARC stair tread covers are ideal for use in any area where frequent use or exposure to slippery environments increases the risk of accidents. The covers fealure a durable gritted surface and a highly vis ible nosing to ensure years of safe, maintenance-free service. The covers also improve the appearance of warped, chipped. and ronen steps and are perfect for use in commercial building applications where it is important to maintain an attractive appearance. Construction The moulded fibreglass stair tread covers are manufactured using high strength fibreglass mat in combination with a choice afresin systems. The top surface is coated with a si lica grit to provide a slip resistant, durable tread. Installation tel.! l it u The covers should be installed on a clean, level surface. Use grout or other suitable material to level uneven surfaces prior to installation. Sand the bottom surface of the stair tread cover ifbonding tread covers to stairs. Two-part epoxy is recommended for bonding. Use wood screws to thru-bolt covers 10 wood stairs. Use expansion anchors, sleeve anchors or concrete screws to fasten covers to concrete stairs. If fastening covers to steel or fibreglass stair treads, use a plate washer with a truss head bolt and nut. Al l fasteners should be 3 16 Stainless Steel. When installing covers over grating treads, field dri ll holes so that fasteners will nol interfere with grating bars. How to Order for thearcmoulded Gratings I Treads: a). Select the model nos. (thickness. mesh size. & mesh pattern) from the respective charts. b). Mention the Resin Code from the chart. c). Mention the colour. you want. d). Mention the maximum Uniform Distributed Load (kg I m!) required, e). Mention also the total quantity required In each size. alon g with the accessories required. O. If you do not find a model suitable 10 your requirements, please furnish au relevant details, enabling us to design and submit you a competitive offer.

PULTRUDED GRATINGS & TREADS : The ARC gratings and treads are high strength pultruded bar type gratings that can be designed and used like traditional metal grates but have the inherent benefits of fib reglass. These problem solving products are ideal replacements for steel or aluminium gratings in corrosive environments or anywhere frequent grating and walkway replacement costs are unacceptable. TheARCfibreglass gratings are a composite of fibreglass reinforcements (fibres and mat) and a thennosetting resin system, produced by the pultrusion process. The pultrusion manufacturing process produces many of the outstanding characteristics of the product. The bearing bars use both longitudinal (glass roving) and multidirectional (glass mat) reinforcements as well as a synthetic surfacing veil to provide unequalled strength and corrosion resistance. The densely packed core of continuous glass rovings gives the bar strength and stiffness in the longitudinal direction while the continuous glass mat provides strength in the transverse direction and prevents chipping, cracking and lineal fracturing. The synthetic surfacing veil provides a 100% pure resin surface for added corrosion resistance and UV protection. The 3-piece cross-rod assembly used in grating forms a strong, unified panel that can be cut and fabricated like a solid sheet. This unique system consists of two continuous, pultruded spacer bars and a centre core wedge. The spacers are notched at each bearing bar so that the bars are both mechanically locked and chemically bonded to the web of each bearing bar. This separates and affixes bearing bars firmly in position and distributes concentrated loads to adjacent bars. A wide variety of bearing bar shapes along with various bearing bar and cross bar spacing's are available depending on the design requirements. a). The traditional 'I' section bearing bar provides maximum fl exibility in design - available in 25mm and 38mm height. b). The 'T' section bearing bar provides a more solid walking surface and prevents catching of pointed heel shoes and other objects between the bars - available in 38mm and SOmm height. c). The 'Solid rectangular' section bearing bar is designed to take heavy vehicular loads - available in 25mm, 32mm, 38mm, 4Smm, SOmm, 57mm and 65mm height.

The pultruded gratings and treads are; Highly Corrosion Resistant Structurally Strong having High Impact and Fatigue Strength Lightweight Easy to Fabricate and Install Low in Maintenance Low in Electrical Conductivity Resistant to Chipping and Cracking having Aesthetically Pleasing Appearance Skid Resistant Rigid Low Thennal Conductivity Non-Sparking The ARC pultruded gratings and treads are available in two standard colours i.e. grey and yellow. Accessories for Pultruded Gratings & T reads a ). Angle The ARC pultruded fibreglass Angle provides a strong, finn base for bearing bars and is pultruded from the same material and in the same manner. b). Panel Installation - The panels are available in size 1.0 mtr x 1.0 mtr. Typically all fasteners used, are Stainless Steel 316. The grating / tread fasteners have low profiles, which eliminates tripping hazards. We recommend using at least 8 clips on a panel of size 1000 mm x 3000 mm. Smaller panels must be secured with no fewer than 4 cl ips. Type Saddle Clip (used for 50% & 60% open area) For attaching grating / tread to supports.

Type Plate Clip (used for 40% open area) For attaching all types of gratings / treads to supports. c). Panel Connectors - Panel Connectors are generally only used at mid span to assist in transferring load from section to section. I Available Pultruded Grating Profiles ri~

ARC Model Nos. Section Section Open Maximum Dimension Area Permissible Height x (%) Span Wldth - (mm) H xwxw ( mm) ARC PG1 2540 ' 1' 25x l 5 xl 5 40 1200 ARC PGI2550 ' I' 25x 15x l5 50 1200 ARC PGI 2560 'I' 25xl5 x l5 60 1200 ARC PG13840 ' I' 38x l 5 x l5 40 1500 ARC PGI 3850 ' I' 38x 15x l5 50 1500 ARC PG 13860 'I' 38xl5xl5 60 1500 ARC PGT 5033 'T' 50 x25 x 15 33 1980 ARC PGT SOSO 'T' 50x25 x 15 50 1980 ARC PGR 2515 'Solid Rectan ular' 25 x I S 60 1372 ARC PGR 3215 'Solid Rectangular' 32 x 15 60 1524 ARC- PGR 3815 'Solid Rectan ular' 38 x 15 60 1828 ARC PGR4515 'Solid Rectan ular' 45 x 15 60 1828 ARC- PGR 5015 'Solid Rectangular' 50 x 15 60 1828 ARC PGR 5715 'Solid Rectan ular' 57 x 15 60 1828 ARC PGR 65 15 'Solid Rectan ular' 65 x 15 60 1828 Maximum Deflection (mm) 6.35 6.35 6.35 Maximum Recommended Uniform Distributed Load (kg 1m') 780 620 51 0 920 760 640 460 350 374 41 2 29' 390 784 1046 1523 How to Order for the ARC Pultruded Gratings! Treads: a). Select the model nos. (section & section dimension) from the respective charts. b). Mention the Resin Code from the chart. c). Mention the colour, you want. d). Mention the maximum Uniform Distributed Load ( kg I m') required. e). Mention also the total quantity required in each size, along with the accessories required. f). If you do not find a model suitable to your requirements, please furnish all releva nt details, enabling us to design and submit you a competitive offer.