pro-skirting PAR-KER Metal floor skirting. Decorative use. Metal skirting which combines exceptional mechanical strength with functional, modern design. Especially recommended for offices and raised floors. Recommended applications - Metal floor skirting. - Residential and public use. - Permanently damp areas or areas in direct contact with water. - Not suitable for swimming pools Materials - Profile: Lacquered aluminium - Design: Printed vinyl. Profile specification - Alloy: 6063 - Profile section: 60 x 12 mm / 100 x 12 mm - Profile thickness: 1.6 mm - Profile length: 1800 mm Design specification - Design: Depending on model, inspired by several PORCELANOSA PAR-KER collections. - Tone: Matt. Substrates: - All substrates suitable for installing ceramic tiles. - Level surfaces suitable for installing ceramics on a thin layer: clean, dry, compact but flat surface (the curvature of the substrate should not exceed 3mm over 2m). - It is essential that walls are flat and well levelled.
Instructions for use - Choose the profile depending on its intended use and the type of ceramic tile. - Clean the joint between the floor tiles and wall, and seal with elastic mastic. - Check the walls are flat and well levelled. Correct any curvature in the substrate. - Clean the substrate of anything which may difficult the profile from bonding. - Apply polyurethane mastic type p-404 and install the profile. - Grout the upper part of the profile and paint. - Before sealing the floor joints, ensure that the sealing material will not scratch or chemically alter the surface of the profile. If so, cover the profile with protective tape. The use of metal tools or abrasives is not recommended as they may scratch the profile surface. Cut the profile with a hacksaw or electric radial cutter at low speed fitted with a multi-use disc. We recommend taking the utmost care when cutting and always make the cut in line with the profile design. For joints on internal and external corners, mitre the profiles at an angle of 45º and adjust. Instructions for use as an access skirting - Choose the profile depending on its intended use and the type of ceramic tile. - Clean the joint between the floor tiles and wall, and seal with elastic mastic. - Check the walls are flat and well levelled. Correct any curvature in the substrate. - Clean the substrate of anything which may prevent the profile from bonding. - Choose screws and wall plugs depending on the type of wall. The fixing hole diameter is 5mm. - Mark the position of the fixing on the wall so it fits into the rear flange on the pro-skirting profile. Maximum spacing between fixings should not exceed 60cm. - Screw the fixing to the substrate and install the pro-skirting profile. - Adjust and level the skirting, leaving the joint between pieces as small as possible. We do not recommended sealing the joints between profiles or between profiles and the wall or floor. - Before sealing the floor joints, ensure that the sealing material will not scratch or chemically alter the surface of the profile. If so, cover the profile with protective tape. The use of metal tools or abrasives is not recommended as they may scratch the profile surface. Cut the profile with a hacksaw or electric radial cutter at low speed fitted with a multi-use disc. We recommend taking the utmost care when cutting and always make the cut in line with the profile design. For joints on internal and external corners, mitre the profiles at an angle of 45º and adjust. Cleaning and maintenance - This type of profile does not require cleaning or maintenance other than same as for ceramic tiles.
- Use neutral cleaning products. Do not use products which contain hydrochloric acid or hydrofluoric acid. We recommend testing prior to use. - Do not use abrasives or metals which may scratch the profile surface. Technical data sheet conditions - This technical data sheet does not correspond to a finished product, it corresponds to a material which, together with other materials, is part of a ceramic installation system and with which a professional may carry out work. The advice contained in this technical data sheet is based on our experience and technical expertise but should be considered as general recommendations only, which together with other products, may assist the professional installer when carrying out the work. - Since we are not familiar with individual site conditions and features, it is the sole responsibility of the user to assess these and, where appropriate, carry out prior tests to confirm that the product is suitable for the work to be carried out. These are especially recommended for applications involving mechanical stress or chemical reactions not described in this data sheet. - This technical data sheet may not take into account all applications and conditions in respect of a material. We therefore recommend that, for situations not referred to in the data sheet, you carry out prior tests and consult our technical department. - This data sheet was updated in January 2017.
Profile section: 100mm / 60mm 12 mm Print technical properties Specification Test Value Thickness UNE-EN ISO 2286 0.25 ± 7.5% Weight UNE-EN ISO 2286 295 gr/m2 Lightfastness ISO 105-A02 8 Density DIN 53.479 1.3 gr/m 3 Strength DIN 35.305 Semi-rigid Shine DIN 67530 4 @ 60ªC Print durability ASTM-D-792 25 seconds at 210º C Dimensional stability 4% 10min/140º) Print chemical properties Substance Acids (Tª < 60ºC). Oxidising acids such as concentrated nitric acid, which attacks PVC at 20ºC, not included Alkalines (T < 60ºC) Hydrocarbons and aromatic hydrocarbons Highly polar organic substances: ketones, esters Aliphatic hydrocarbons Running water Detergents Durability Not resistant
Print chemical resistance Stain Exposure time Value* Acetic acid (10%) 16 h 5 Citric acid (10%) 16 h 5 Ammonia (10%) 16 h 5 Ethil alcohol (48%) 16 h 5 Red wine 16 h 5 Beer 16 h 5 Cola soft-drink 16 h 5 Coffe (40 g / litro) 16 h 5 Black tea ( 10 g / litro) 16 h 5 Blackcurrant juice 16 h 5 Condensed milk 16 h 5 Acetone 10 seconds / 16 hours 5 / 1 Etil-butil acetate 10 seconds / 16 hours 5 / 1 Butter 16 h 5 Olive oil 16 h 5 Mustard 16 h 5 Desinfectant (phenol) 16 h 5 Black pen ink 16 h 5 Cleaning agent 16 h 5 * Chemical resistance table: Appearence Value No visible changes. 5 Slight changes in brightness and / or color only visible from certain viewing 4 angles. Moderate changes in brightness and / or color. The test surface remains 3 unchanged. Significant changes in brightness and / or color and / or slight changes in 2 surface structure. Strong changes in surface structure: blistering, cracking or delamination. 1
PAR-KER pro-skirting B71142022 100178480 ASCOT ARCE 100 180 B71142017 100178456 ASCOT GREY 100 180 B71142024 100178483 ASCOT OLIVO 100 180 B71142021 100178484 ASCOT ROBLE 100 180 B71142029 100178466 ASCOT TEKA 100 180 B79999021 100193595 ASCOT ARCE 60 180 B79999025 100193528 ASCOT GREY 60 180 B79999033 100193611 ASCOT OLIVO 60 180 B79999046 100193640 ASCOT ROBLE 60 180 B79999045 100193642 ASCOT TECA 60 180 B71142027 100178474 CHELSEA ARCE 100 180 B71142016 100178439 CHELSEA BONE 100 180 B71142014 100178457 CHELSEA CAMEL 100 180 B71142019 100178485 CHELSEA NUT 100 180 B71142025 100178467 CHELSEA SILVER 100 180 B79999034 100193636 CHELSEA ARCE 60 180 B79999027 100193600 CHELSEA BONE 60 180 B79999028 100193549 CHELSEA CAMEL 60 180 B79999047 100193643 CHELSEA NUT 60 180 B79999048 100193644 CHELSEA SILVER 60 180 B71142020 100178475 OXFORD ACERO 100 180 B71142031 100178471 OXFORD ANTRACITA 100 180 B71142013 100178436 OXFORD BLANCO 100 180 B71142015 100178435 OXFORD CASTAÑO 100 180 B71142012 100178437 OXFORD COGNAC 100 180 B71142023 100178462 OXFORD NATURAL 100 180 B71142028 100178463 OXFORD SILVER 100 180
B79999049 100193645 OXFORD ACERO 180 X 6CM 60 180 B79999050 100193646 OXFORD ANTRACITA 60 180 B79999023 100193597 OXFORD BLANCO 60 180 B79999040 100193605 OXFORD CASTAÑO 60 180 B79999024 100193547 OXFORD COGNAC 60 180 B79999026 100193598 OXFORD NATURAL 60 180 B79999042 100193634 OXFORD SILVER 60 180 B79999020 100189248 MANHATTAN COLONIAL 100 180 B79999017 100191461 MANHATTAN MAPLE 100 180 B79999016 100191470 MANHATTAN COGNAC 100 180 B79999019 100191481 MANHATTAN SILVER 100 180 B79999018 100191490 MANHATTAN NATURAL 100 180 B79999030 100193603 MANHATTAN COLONIAL 60 180 B79999037 100193604 MANHATTAN MAPLE 60 180 B79999029 100193602 MANHATTAN COGNAC 60 180 B79999036 100193624 MANHATTAN SILVER 60 180 B79999043 100193623 MANHATTAN NATURAL 60 180 PAR-KER pro-skirting fixing B70104237 100193608 PRO-SKIRTING (B-50UD) FIXING 15 30