Europe Bill Acceptor EBA - 10 - SD2 CHAPTER 2 Operation Manual DWG No. 990-1 1-0 2-01 Date 97-02 JAPAN CASHMACHINE CO., LTD. Copyright 1997 Japan Cash Machine
1 Features Validator EBA-10-SD2 provides the following features.!setting for accepting a bill You can set the DIP switch to accept or refuse each of 5 types of bills independently. You can also set the DIP switch to accept all 5 types of bills.!simple bill collection Since you can detach the stacker box itself from the main unit, the bills can be collected easily. Also, the stacker box is provided with a lock to offer high security. The stacker box can store up to 400 bills.! Bill theft prevention mechanism A security device is installed to prevent any illegal action. Once a bill is fed into the unit, it cannot be pulled out. Japan Cash Machine Co., Ltd. Class EBA-10-SD2 Chapter 2(4) Date 02-97 Dwg No. 990-02-01 Page 1
2 Component Name Red LED Japan Cash Machine Co., Ltd. Class EBA-10-SD2 Chapter 1 Date 02-97 Dwg No. 990-01-01 Page 1
3 Precautions 1. Do not insert a torn, 2. Never expose the unit in 3. Do not install the unit wet bill. It will get in water. The unit in a dusty invironment. Jammed in the unit. contain several precision Dust will lower the electronic devices which can be damaged if water or any liquid is sprayed or spilled into the unit. performance of the bill sensor. 4 Collecting Bills 1. Unlock and pull out the stacker box. 2. Take out the bills. Japan Cash Machine Co., Ltd. Class EBA-10-SD2 Chapter 1 Date 02-97 Dwg No. 990-01-01 Page 1
5 When the Acceptor is Jammed (1) When bills are jammed near the entrance of the stacker box, unlock the box and pull it out to remove the jammed bills. (2) Loosen 2 knobs each from either side to open the acceptor head and remove the jammed bills. Japan Cash Machine Co., Ltd. Class EBA-10-SD2 Chapter 2(4) Date 02-97 Dwg No. 990-04-01 Page 4
(1) When you cannot remove jammed Bills even after opening the acceptor head, open the cover of bill theft prevention unit to remove the jammed bills and strings. (4) When bills are jammed in the feed route, remove 2 screws at the back and 2 screws each from either side of the stacker storage unit to pull out the feed unit and remove the jammed bills. Japan Cash Machine Co., Ltd. Class EBA-10-SD2 Chapter 2(4) Date 02-97 Dwg No. 990-04-01 Page 5
6 Cleaning When the scanning unit and its sensor becomes dirty, this could cause paper jams and deterioration of the bill sensing capability. Periodically open the acceptor and bill theft prevention unit and clean the inner parts of these units. Use a soft cloth or cotton swab to clean the inner parts. If you cannot remove a stain, wipe it using a cloth or cotton swab moistened with a standard head cleaner sold in the market. Never use organic solvents such as thinners to clean the inside parts: Do no use organic solvent like thinner. Japan Cash Machine Co., Ltd. Class EBA-10-SD2 Chapter 2(4) Date 02-97 Dwg No. 990-0-01 Page 6
7 Installation (1) Installing the unit: There are 4 installation holes each on the rear and bottom cover panels of the unit. (2) Replacing the width guides of the bill insertion slot To replace the width guides of the bill insertion slot, remove the screws from the back side of these width guides. Bank notes to accept Between Width min 65mm ~ 78 mm Length min 125mm ~ 170mm Japan Cash Machine Co., Ltd. Class EBA-10-SD2 Chapter 2(4) Date 02-97 Dwg No. 990-04-01 Page 7
8 Outline of Interface The following 2 types of interfaces can be provided in Validator EBA-1 O-SD2, depending on the ROM. (1) ID-001 interface The ID-001 interface offers parallel interface support for 7 output lines and 3 input lines. The status of the acceptor is output by the ABN, BSY, and STKT output signals. The type of currency received is output by the VED1 to VEND3 and VALID output signals. The acceptor operation can be controlled by the ACK, REJ, and INH input signals. See the attached "Communications Specifications ID-001 for communication specifications. (2) ID-003 interface The ID-003 interface is a 2-way serial interface. You can control the acceptor status and operation of the acceptor and confirm the settings of each function by sending a polling "Status Request" and commands ("Operation command" and "Setting command") from the controller. See the attached "Communications Specifications ID-003" for communication specifications. Japan Cash Machine Co., Ltd. Class EBA-10-SD2 Chapter 2(4) Date 02-97 Dwg No. 990-04-01 Page 8
9 Input/Output ID-001 interface circuit ID-003 interface circuit circuit for output signal to turn ON the display LED Japan Cash Machine Co., Ltd. Class EBA-10-SD2 Chapter 2(4) Date 02-97 Dwg No. 990-04-01 Page 9
10 Cabling Japan Cash Machine Co., Ltd. Class EBA-10-SD2 Chapter 2(4) Date 02-97 Dwg No. 990-04-01 Page 10
12 DIP Switch Setting DIP switch setting (ID-001) You can set the type of currency to be received, the escrow mode, and other functions using the DIP switch settings. DIP switch setting (ID-003) The available DIP switch settings are as follows. Japan Cash Machine Co., Ltd. Class EBA-10-SD2 Chapter 2(4) Date 02-97 Dwg No. 990-04-01 Page 13