Material Specialised MSDS Safety Data Wood SheetLacquer Interior SPS SPS1321A-F 1301 Robust, non solvent, water based, interior wood lacquer with a voc level well below the 2005 Montreal Protocol Guidelines SELECTION DATA Type Recommended Uses Not Recommended For Approval Chemical Resistance A premium quality wood lacquer in matt, gloss and tinted options For internal application on wood, wood chipboard, hard board, MDF, plywood etc. Exterior use Independently tested in a weather-o-meter Good resistance to household chemicals, non-alcoholic beverages, red wine, white wine, beer, powder coffee, black tea, blackcurrant, juice, condensed milk, butter, olive oil, mustard, common salt onions, acetic acid, and citric acid Thermal Resistance Spread of Flame Index (SFI) 8 Smoke Developed index (SDI) 4 Continuous surface: 100 C Non-continuous: 150 C Compatible Coatings n/a Solids 40% +/- 1% VOC 120-150g per ltr Specific Gravity 1.05 +/- 0.05 Recommended Dry Film Thickness (per coat) 40 microns per coat Coverage 10-12 sqm/ltr Dry Time (@18 C) 15 mins Recoat: 30 mins Drying time may vary according to atmospheric conditions Shelf Life 1 year if kept sealed and under cover in cool, dry environment Do not allow to freeze Transportation Not classified as a dangerous good, safe to transport by land, sea or air using standard best practice precautions Pack Size 10 ltrs Colour Clear, tinted, matt, semi gloss, gloss SPS Coatings Ltd www.spscoatings.com. New Zealand Sales Office: Phone +64 9 920 6015 or +64 9 920 6016 Fax +64 9 273 1240 Email sales@spscoatings.co.nz
Material MSDS Safety Data Sheet SPS SPS1321A-F 1301 APPLICATION Key Advantages Safety Non-hazardous to environment and the applicator Easy to apply No sealer required, can be applied directly to substrate Minimal grain lift Sands well, no clogging of paper Excellent edge build up Quick drying Non yellowing This product contains no solvents and is non-toxic, however it is recommended that a dust mask be used to protect from atomised material when spraying Surface Preparation Ensure the substrate is clean and free of loose material. On new wood, it is recommended to sand with 220 grit paper to achieve a high grade finish Conditions Do not apply in temperatures below 5 C or above 50 C Spray: Conventional/HVCP Use approx 0.9 to 1.2mm fluid tip and appropriate aircap for clear lacquer Coloured lacquers use approx 1.0 to 1.4mm fluid tip and appropriate air cap It should be held approximately 30 to 35 cms at right angles to the surface Airless Tip Size: 0.009-0.013 Output PSI: 1800-2300 Filter Size: 100 mesh Brush/Roller Brushing is only recommended to touch up small areas Apply with small strokes, using a natural bristle brush Use a short-nap mohair roller for roller application This document does not express or imply any product guarantee or warranty For application specific product guarantees or warranties please contact our Technical Manager
Material Specialised MSDS Safety Data Wood SheetLacquer Exterior SPS SPS1321G-L 1301 Robust, non solvent, water based, exterior wood lacquer with a voc level well below the 2005 Montreal Protocol Guidelines SELECTION DATA Type Recommended Uses Not Recommended For Approval Chemical Resistance A premium quality exterior wood lacquer in matt, gloss and tinted options For internal application on wood, wood chipboard, hard board, MDF, plywood etc. Interior use Independently tested in a weather-o-meter Good resistance to household chemicals, non-alcoholic beverages, red wine, white wine, beer, powder coffee, black tea, blackcurrant, juice, condensed milk, butter, olive oil, mustard, common salt, onions, acetic acid, and citric acid Thermal Resistance Spread of Flame Index (SFI) 8 Smoke Developed index (SDI) 4 Continuous surface: 100 C Non-continuous: 150 C Compatible Coatings n/a Solids 40% +/- 1% VOC 120-150g per ltr Specific Gravity 1.05 +/- 0.05 Recommended Dry Film Thickness (per coat) 40 microns per coat Coverage 10-12 sqm/ltr Dry Time (@18 C) 15 mins Recoat: 30 mins Drying time may vary according to atmospheric conditions Shelf Life 1 year if kept sealed and under cover in cool, dry environment Do not allow to freeze Transportation Not classified as a dangerous good, safe to transport by land, sea or air using standard best practice precautions Pack Size 10 ltrs Colour Clear, tinted, matt, semi gloss, gloss SPS Coatings Ltd www.spscoatings.com. New Zealand Sales Office: Phone +64 9 920 6015 or +64 9 920 6016 Fax +64 9 273 1240 Email sales@spscoatings.co.nz
Material MSDS Safety Data Sheet SPS SPS1321G-L 1301 APPLICATION Key Advantages Safety Non-hazardous to environment and the applicator Easy to apply No sealer required, can be applied directly to substrate Minimal grain lift Sands well, no clogging of paper Excellent edge build up Quick drying Non yellowing This product contains no solvents and is non-toxic, however it is recommended that a dust mask be used to protect from atomised material when spraying Surface Preparation Ensure the substrate is clean and free of loose material. On new wood, it is recommended to sand with 220 grit paper to achieve a high grade finish Conditions Do not apply in temperatures below 5 C or above 50 C Spray: Conventional/HVCP Use approx 0.9 to 1.2mm fluid tip and appropriate aircap for clear lacquer Coloured lacquers use approx 1.0 to 1.4mm fluid tip and appropriate air cap It should be held approximately 30 to 35 cms at right angles to the surface Airless Tip Size: 0.009-0.013 Output PSI: 1800-2300 Filter Size: 100 mesh Brush/Roller Brushing is only recommended to touch up small areas Apply with small strokes, using a natural bristle brush Use a short-nap mohair roller for roller application This document does not express or imply any product guarantee or warranty For application specific product guarantees or warranties please contact our Technical Manager
Specialised High Build Acrylic Clear Coat SPS 1324 Robust, non solvent, water-based high build acrylic clear coat with a voc level well below the 2005 Montreal Protocol Guidelines SELECTION DATA Type Recommended Uses Not Recommended For Approval Chemical Resistance A premium quality High Build Acrylic Clear Coat in matt, gloss and tinted options for photo frames, table tops etc. For internal application on wood, wood chipboard, hard board, MDF, plywood etc. Exterior use Independently tested in a weather-o-meter Good resistance to household chemicals, non-alcoholic beverages, red wine, white wine, beer, powder coffee, black tea, blackcurrant, juice, condensed milk, butter, olive oil, mustard, common salt onions, acetic acid, and citric acid Thermal Resistance Spread of Flame Index (SFI) 8 Smoke Developed index (SDI) 4 Continuous surface: 100 C Non-continuous: 150 C Compatible Coatings n/a Solids 40% +/- 1% VOC 120-150g per ltr Specific Gravity 1.05 +/- 0.05 Recommended Dry Film Thickness (per coat) 50 microns per coat Coverage 10-12 sqm/ltr Dry Time (@18 C) 15 mins Recoat: 30 mins Drying time may vary according to atmospheric conditions Shelf Life 1 year if kept sealed and under cover in cool, dry environment Do not allow to freeze Transportation Not classified as a dangerous good, safe to transport by land, sea or air using standard best practice precautions Pack Size 10 ltrs Colour Either clear or standard architectural colour range. Available in matt, satin, semi gloss, gloss SPS Coatings Ltd www.spscoatings.com. New Zealand Sales Office: Phone +64 9 920 6015 or +64 9 920 6016 Fax +64 9 273 1240 Email sales@spscoatings.co.nz
SPS 1324 APPLICATION Key Advantages Safety Non-hazardous to environment and the applicator Easy to apply No sealer required, can be applied directly to substrate Minimal grain lift Sands well, no clogging of paper Excellent edge build up Quick drying Non yellowing This product contains no solvents and is non-toxic, however it is recommended that a dust mask be used to protect from atomised material when spraying Surface Preparation Ensure the substrate is clean and free of loose material. On new wood, it is recommended to sand with 220 grit paper to achieve a high grade finish Conditions Do not apply in temperatures below 5 C or above 50 C Spray: Conventional/HVCP Use approx 0.9 to 1.2mm fluid tip and appropriate aircap for clear lacquer Coloured lacquers use approx 1.0 to 1.4mm fluid tip and appropriate air cap It should be held approximately 30 to 35 cms at right angles to the surface Airless Tip Size: 0.009-0.013 Output PSI: 1800-2300 Filter Size: 100 mesh Brush/Roller Brushing is only recommended to touch up small areas Apply with small strokes, using a natural bristle brush Use a short-nap mohair roller for roller application This document does not express or imply any product guarantee or warranty For application specific product guarantees or warranties please contact our Technical Manager
Specialised Medicoat SPS 1325 A durable, germ resistant medical coat with a voc level well below the 2005 Montreal Protocol Guidelines SELECTION DATA Type Recommended Uses Not Recommended For Germ Resistance Chemical Resistance A premium quality, non-solvent, antistatic, germ resistant water-based lacquer For internal use in medical facilities ie hospitals, clinics, dental surgeries Employs closed pore technology Resistant to adhesion by inks and other paints Resistance to mould and mildew Thermal Resistance Spread of Flame Index (SFI) 8 Smoke Developed Index (SDI) 4 Continuous surface: 100 C Non-continuous: 150 C Compatible Coatings Will perform over most existing architectural coatings Solids 40% +/- 1% VOC 120-150g per ltr Specific Gravity 1.05 +/- 0.05 Recommended Dry Film Thickness (per coat) 40 microns per coat Coverage 10-12 sqm/ltr Dry Time (@18 C) 15 mins Recoat: 30 mins Drying times may vary with atmospheric conditions Shelf Life 1 year if kept sealed and under cover in cool, dry environment Do not allow to freeze Transportation Not classified as a dangerous good, safe to transport by land, sea or air using standard best practice precautions Pack Size 10 ltrs Colour Clear SPS Coatings Ltd www.spscoatings.com. New Zealand Sales Office: Phone +64 9 920 6015 or +64 9 920 6016 Fax +64 9 273 1240 Email sales@spscoatings.co.nz
SPS 1325 APPLICATION Key Advantages Safety Non-hazardous to environment and the applicator Easy to apply No sealer required, can be applied directly to substrate Minimal grain lift Sands well, no clogging of paper Excellent edge build up Quick drying Non yellowing This product contains no solvents and is non-toxic, however it is recommended that a dust mask be used to protect from atomised material when spraying Surface Preparation Ensure the substrate is clean and free of loose material. It is recommended to sand existing coating with 220 grit paper to achieve a high level of adhesion Conditions Do not apply in temperatures below 5 C or above 50 C Spray: Conventional/HVCP Use approx 0.9 to 1.2mm fluid tip and appropriate aircap for clear lacquer Coloured lacquers use approx 1.0 to 1.4mm fluid tip and appropriate air cap It should be held approximately 30 to 35 cms at right angles to the surface Airless Tip Size: 0.009-0.013 Output PSI: 1800-2300 Filter Size: 100 mesh Brush/Roller Brushing is only recommended to touch up small areas Apply with small strokes, using a natural bristle brush Use a short-nap mohair roller for roller application This document does not express or imply any product guarantee or warranty For application specific product guarantees or warranties please contact our Technical Manager
Specialised Anti-Graffiti Clear Coat SPS 1326 A high performance, graffiti resistant clear coat with a voc level well below the 2005 Montreal Protocol Guidelines SELECTION DATA Type Recommended Uses Not Recommended For Approvals A premium quality water-based anti-graffiti clear coat which is quick drying and chemical resistant For internal and external use as anti-graffiti protective finishing coat over existing coatings. Ideal for schools and other public facilities susceptible to graffiti attacks Independently tested in a weather-o-meter Chemical Resistance Resistant to adhesion by inks and other paints Thermal Resistance Spread of Flame Index (SFI) 8 Smoke Developed Index (SDI) 4 Continuous surface: 100 C Non-continuous: 150 C Compatible Coatings Will perform over most existing coatings Solids 40% +/- 1% VOC 120-150g per ltr Specific Gravity 1.10 +/- 0.05 Recommended Dry Film Thickness (per coat) 40 microns per coat Coverage 10-12 sqm/ltr Dry Time (@18 C) 15 mins Recoat: 30 mins Drying times may vary with atmospheric conditions Shelf Life 1 year if kept sealed and under cover in cool, dry environment Do not allow to freeze Transportation Not classified as a dangerous good, safe to transport by land, sea or air using standard best practice precautions Pack Size 10 ltrs Colour Clear SPS Coatings Ltd www.spscoatings.com. New Zealand Sales Office: Phone +64 9 920 6015 or +64 9 920 6016 Fax +64 9 273 1240 Email sales@spscoatings.co.nz
SPS 1326 APPLICATION Key Advantages Safety Non-hazardous to environment and the applicator Easy to apply Can be applied directly to substrate Sands well, no clogging of paper Excellent edge build up Quick drying Non yellowing This product contains no solvents and is non-toxic, however it is recommended that a dust mask be used to protect from atomised material when spraying Surface Preparation To be applied over SPS architectural products Conditions Do not apply in temperatures below 5 C or above 50 C Spray: Conventional/HVCP Use approx 0.9 to 1.2mm fluid tip and appropriate aircap for clear lacquer Coloured lacquers use approx 1.0 to 1.4mm fluid tip and appropriate air cap It should be held approximately 30 to 35 cms at right angles to the surface Airless Tip Size: 0.009-0.013 Output PSI: 1800-2300 Filter Size: 100 mesh Brush/Roller Brushing is only recommended to touch up small areas Apply with small strokes, using a natural bristle brush Use a short-nap mohair roller for roller application This document does not express or imply any product guarantee or warranty For application specific product guarantees or warranties please contact our Technical Manager
Specialised Graffiti Ink Remover SPS 1348 Non-solvent ink remover DESCRIPTION Water based Graffiti ink remover COLOUR Colourless to faint yellowish liquid ADVANTAGES Easy to use Leaves substrate very smooth No chemical reaction No mineral solvents Environment/worker friendly No toxic fumes Removes graffiti from all surfaces (use in conjunction with SPS anti-graffiti lacquer) APPLICATION Apply with soft brush (can be sprayed) onto the graffiti and clean with a rag. Rinse well with water to clean SAFETY Wear neoprene gloves, rinse well after use TRANSPORTATION Not classified as a dangerous good, safe to transport by land, sea or air using standard best practice precautions TECHNICAL DATA Pack Size 5, 10 ltrs No. of components 1 Shelf Life 1 year Application Temperature 5 C - 50 C Toxicity Nil Fire Hazard None Storage Undercover in cool and dry conditions. Do not allow to freeze This document does not express or imply any product guarantee or warranty SPS Coatings Ltd www.spscoatings.com. New Zealand Sales Office: Phone +64 9 920 6015 or +64 9 920 6016 Fax +64 9 273 1240 Email sales@spscoatings.co.nz
Specialised TTC Tile Mould/Moss Treatment SPS 1349 Non-solvent concentrate DESCRIPTION Premium quality pre-prep concentrate to kill moss, mould, lichen on various surfaces COLOUR Yellowish ADVANTAGES Kills spores to help stop future growth of moss, mould, lichen etc. Much easier to water blast and can be used at low pressure to minimise damage to the surface Leaves substrate very smooth Easy to use No chemical reaction No mineral solvents Environment/worker friendly No toxic fumes APPLICATION Dilute 1:10 and spray on roof. Leave it for 3 to 4 days to kill moss, mould, lichen etc. and then water blast SAFETY Wear neoprene gloves, rinse well after use TRANSPORTATION Not classified as a dangerous good, safe to transport by land, sea or air using standard best practice precautions TECHNICAL DATA Pack Size 5, 10 ltrs No. of components 1 Shelf Life 1 year Application Temperature 5 C - 50 C Toxicity Nil Fire Hazard None Storage Undercover in cool and dry conditions. Do not allow to freeze This document does not express or imply any product guarantee or warranty SPS Coatings Ltd www.spscoatings.com. New Zealand Sales Office: Phone +64 9 920 6015 or +64 9 920 6016 Fax +64 9 273 1240 Email sales@spscoatings.co.nz
Specialised Concrete Tile Mould/Moss Treatment SPS 1350 Non-solvent concentrate DESCRIPTION Premium quality concrete tile treatment concentrate to kill moss, mould, and lichen on roofs COLOUR Colourless to faint yellowish liquid ADVANTAGES Kills spores to help stop future growth of moss, mould, lichen etc Much easier to waterblast and can be used at low pressure to minimise damage to the surface Easy to use No chemical reaction No mineral solvents Environment/worker friendly No toxic fumes APPLICATION Dilute 1:10 and spray on roof. Leave it for 3 to 4 days to kill moss, mould, lichen etc. and then waterblast the roof SAFETY Wear neoprene gloves, rinse well after use TRANSPORTATION Not classified as a dangerous good, safe to transport by land, sea or air using standard best practice precautions TECHNICAL DATA Pack Size 5, 10 ltrs No. of components 1 Shelf Life 1 year Application Temperature 5 C - 50 C Toxicity Nil Fire Hazard None Storage Undercover in cool and dry conditions. Do not allow to freeze This document does not express or imply any product guarantee or warranty SPS Coatings Ltd www.spscoatings.com. New Zealand Sales Office: Phone +64 9 920 6015 or +64 9 920 6016 Fax +64 9 273 1240 Email sales@spscoatings.co.nz
Specialised Plast O Fix SPS 1371 A specialist powder to improve water-proofing and expansion cracking resistance SELECTION DATA Type A pale yellow powder additive to cement and plaster Recommended Uses For use in dry mortar powder for construction adhesives and for cement based waterproof systems for balconies, terraces, and cellars. Also in ceramic tile adhesives and watertight tile adhesives Not Recommended For Use as a plaster substitute Thermal Expansion Properties Prevents plaster from cracking when temperatures fluctuate between -10 C and 40 C Chemical Resistance Good resistance to household chemicals, non-alcoholic beverages, red wine, white wine, beer, powder coffee, black tea, blackcurrant, juice, condensed milk, butter, olive oil, mustard, common salt onions, acetic acid, and citric acid Compatible Coatings n/a Solids 98% +/- 1% PH Value (30% wt in water) 7.0-8.0 Shelf Life Plast'o'fix can be stored for up to 6 months in a cool, dry place Containers that have been opened must be used up as quickly as possible as the product becomes lumpy when exposed to atmospheric humidity Care must be taken not to expose it to elevated temperatures or pressure, as this can cause caking Transportation Not classified as a dangerous good, safe to transport by land, sea or air using standard best practice precautions Pack Size 10, 20kg SPS Coatings Ltd www.spscoatings.com. New Zealand Sales Office: Phone +64 9 920 6015 or +64 9 920 6016 Fax +64 9 273 1240 Email sales@spscoatings.co.nz
SPS 1371 APPLICATION Safety Conditions Mixing: Plaster Mortar mix (for swimming pools) Mortar mix (for general use) If properly handled and used for the intended purpose it has no harmful effect on health according to our experience and the information available to us Prolonged exposure to the product can cause irritation of the skin and mucous membranes Care should be taken to avoid excessive heat development when the dry components are mixed Mix Plast 'O' Fix at a ratio of 3% of the dry plaster weight Mix Plast 'O' Fix at a ratio of:8% of the dry Mortar mix weight Mix Plast 'O' Fix at a ratio of:3% of the dry Mortar mix weight This document does not express or imply any product guarantee or warranty For application specific product guarantees or warranties please contact our Technical Manager