Product Catalogue Telecommunication Hardware
Content Above-Surface Hardware Guy Clamp, Suspension Clamp and Suspension Pulley 4-5 Utility Pole Top Cover 6 Screw Anchor and Turnbuckle 7 Wall Hook, Guy Hook, Thimble, and Wire Clamp 8 Crossarm with Hooks and Accessories 9 Cable Protection Channels 10-11 Cable Marker 11 Below-Surface Hardware Cable Support Rail, Cable Support, and Sleeve Support Tray 13-15 Shaft Ladder and Ladder Guard 16-18 Dirt Collecting Tray and Tool Yoke 19-20 Wall Bushing 21 Spacer and Belt Clamp 22 Earth Rod 23 Wire clamp Thimble Cable marker Turnbuckle Screw anchor
Above-Surface Hardware Above-Surface Hardware Utility pole top cover Guy hook Crossarm with hooks Guy clamp Wall hook Suspension pulley Pole Saddle clamp Cable Protection Channels Ground level (Schematic representation)
Above-Surface Hardware Cable Suspension Guy clamp Convenient and reliable suspension of installation cables on poles and building walls Steel housing with two tapered plastic clamping jaws, clamping down under tensile stress Suspension e.g. on guy hooks or crossarm hooks Temperature range: -30 C to +60 C PA6 GF30 DIN 50976 190 to 540 Meas. 2 48 to 150 Meas. 3 Guy hook Open clamping jaws Meas. 1 Cable Cable Clamping the cable under tensile stress Pole Housing Clamping jaws (PA6 GF30) Size for Permitted Weight L x W jaw eyelet cable ø tensile load in kg in mm Meas. 1 Meas. 2 Meas. 3 in mm in kn in mm in mm in mm SS 5.5 to 9.5 2,5 0.15 190 x 48 min. 35 18 60 59.1440.00.00 S 8.5 to 13.5 3,5 0.4 250 x 67 min. 50 28 70 59.1442.00.00 M 12.5 to 17.5 4,5 0.7 300 x 80 min. 55 36 81 59.1444.00.00 L 16.5 to 24 7,5 1.5 420 x 116 min. 75 26 113 59.1446.00.00 XL 22.5 to 32 11 3.0 540 x 150 min. 95 36 146 59.1448.00.00 4
Above-Surface Hardware Cable Suspension Suspension Clamp PS 510 Suspension of messenger cables Clamping the messenger with two plastic clamping jaws Stainless steel hook (flexible) for suspending the suspension clamp from the support hook Stainless steel hook PA6 GF30 Clamping jaws Stainless Steel Clamping diameter A Clamping diameter B Cable Messenger Nut and bolt made of stainless steel Suspension clamp Clamping diameter in mm A B PS 510 5 to 7 8 to 10 59.138200.00 Suspension Pulley Suspension pulley for mounting, guiding and bearing cables used in above-ground lines Consisting of two hot-dipped steel plates holding pivoting castor made of PA6-GF30 Temperature range: -40 C to +60 C PA6 GF30 Cable 298 26 36 46 150 Size for cable ø in mm Permitted tensile load in kn Weight in kg 150/15-26 15 to 26 3 1.0 59.1341.00.00 150/25-36 25 to 36 4 1.0 59.1351.00.00 150/35-46 35 to 46 5 1.0 59.1361.00.00 Pole 5
Above-Surface Hardware Pole and Cable Suspension Pole Suspension (Pole with Anchor) Spigot Cover Wall hook Wire cable Wire clamp Wire sleeve (injury protection) Wire cable Wire clamp Thimble Turnbuckle (includes eyebolt) Pole Screw anchor Ground level 1.5 m 1.5 m (Schematic representation) Screw anchor Spigot Cover Spigot Cover Covering the slanted tops of utility poles Comes with 6 nails (3x per slope) Nail Weight in kg Pieces 0.1 10 59.0841.00.00 Pole 6
Above-Surface Hardware Pole and Cable Suspension Screw anchor Securing and reinforcing poles Installation by auguring into the ground, with the longitudinal axes of the helical anchor pointing in the direction of the anchor cable 2000 Pinhole ø 5 145 10 1710 Screw anchor Weight in kg M 16 3.7 59.1606.00.00 Turnbuckle Suspension of anchor cable or messenger Turnbuckle with 2x eyebolts Turnbuckle with 1x eyebolt 100 Right-hand thread 170 22 48 165 Left-hand thread Pinhole ø 5 Turnbuckle M 16 with 2x eyebolt 59.1611.00.00 M 16 with 1x eyebolt 59.1612.00.00 7
Above-Surface Hardware Pole and Cable Suspension Wall Hook Wall hook with wood thread For screwing into masonry or wooden pole 152 68 30 ø 12 Wall Weight in kg Pieces Pole 0.2 10 59.1634.00.00 Guy Hook For suspension points under tensile stress e.g. overhead cable Comes with 2x washer and hexagon nut 64 Weight in kg 0.87 59.1635.00.00 ø 16 262 294 Pole 200 Thimble (Thimble 70 s) 100 Loop shaping and protection of wire cables 18 15 Thimble Thimble 70 s 59.1609.00.00 40 R = 5.5 10 Wire Clamp (DIN 48335) For connecting wire ropes for rope ø in mm 7.5 to 10.5 59.1610.00.00 Washer 18 (DIN 126) Wire rope Hexagon nut M16 (DIN 555) Supporting ring C (DIN 48335) Clamping plate A (DIN 48335) Clamping ear B (DIN 48335) 8
Above-Surface Hardware Crossarms and Accessories Crossarm (A 550) with Hooks Installation on wooden pole for parallel line routing of up to four lines Complete with installation material Crossarm Mounting bracket Arm clip Crossarm Hooks for crossarm Pole 210 / 240 / 270 Pole 105 / 120 / 140 ø 16 50 30 65 159 Hooks for crossarm incl. hexagon nut (M16) ø 130 ø 170 ø 200 Arm clip with hexagon nuts and ring washers (M16) 64 30 Mounting bracket (DIN 48322) R = 60 120 Crossarm Length 550 mm 59.1627.00.00 Crossarm accessories Mounting bracket 120 59.1628.00.00 Hooks for crossarm 59.1629.00.00 Arm clip 130 59.1630.00.00 Arm clip 170 59.1631.00.00 Arm clip 200 59.1632.00.00 9
Above-Surface Hardware Cable Protection Cable Protection Channel 1700 Protection of cable mounted on walls or poles against external damages Overlapping assembly if several cable protection channels are used Installation of the saddle clamp on curved or level surface (e.g. pole or wall) and additionally with clamp tie plate for mounting on uneven surfaces Clamp Guy clamp 26 1 25 37 Cable protection channel (cross section) Distribution point 56 Saddle clamp Cable max ø 25 Saddle clamp Cable Pole 67 max. ø 25 Saddle clamp Wall Pole Length Pieces 1700 mm 20 59.0011.00.00 Cable protection channel Cleat Pieces Upper part 60 59.0021.00.00 Bottom part 60 59.0031.00.00 min. 10 cm Ground level (Schematic representation) 10
Above-Surface Hardware Cable Protection and Marker Cable Protection Channel Protection of cable mounted on walls or poles against external damages Installation with suitable fixing clamp model (3 pieces for each cable protection channels) Without sleeve nut (not overlapping) A = 90 B = 145 C = 110 galvanized A = 33 B = 65 C = 50 A = 26 B = 60 C = 40 Cable protection channel (cross section) Cable Clamp A = 45 B = 88.5 C = 65 Wall Model A (length 3000 mm) 84.0001.00.00 B (length 3000 mm) 84.0031.00.00 C (length 3000 mm) 84.0015.00.00 Clamp for model A 84.0011.00.00 B 84.0021.00.00 C 84.0016.00.00 Cable Marker 82 Detection of underground cable systems in undeveloped locations without fixed points for calibrating the cable system Galvanised anchoring and connector to the ground connection with anchoring nails (3x) Captive plastic head (marking with labelling plate possible) Comes with anchoring and connecting piece, plastic head, locking bolt, and labelling plate. Labelling plate HOT- Ground level Cable marker Complete cable marker 59.0001.00.00 Plastic head 59.0001.03.00 140,5 250 162 50 Plastic head Anchoring nail Length in mm Pieces 500 3 59.0361.00.00 700 3 59.0371.00.00 Ground level Anchoring and connecting piece 350 or 500 11
Below-Surface Hardware Above-Surface Hardware Cable support rail (set in concrete) Shaft ladder (straight) Sleeve support tray Cable support rail (bolted down) Cable support Cable vault (Schematic representation) Spacer
Below-Surface Hardware Cable Vault and Junction Box Cable Support Rail for Setting in Concrete Cable supports and cable support straps are fastened using the punched slots with a grid dimension of 75 In the case of prefab concrete shafts, the cable support rail is set flush into the concrete at predefined intervals. 28 70 22 Length in mm Number of bolts (ø 10 x 75 mm) 670 7 59.0111.00.00 75 820 8 59.0112.00.00 970 9 59.0113.00.00 1120 10 59.0114.00.00 1270 11 59.0115.00.00 670 to 2545 1345 12 59.0116.00.00 1645 14 59.0117.00.00 1945 16 59.0118.00.00 2245 18 59.0119.00.00 2545 20 59.0120.00.00 Shaft wall concrete C20/25 Special lengths available upon request. Cable Support Rail Cable supports and cable support straps are fastened using the punched slots with a grid dimension of 75 Post-construction installation on the shaft wall at predefined intervals, using heavy duty anchors Comes with heavy duty anchor M8 x 65 Standard FTZ 736 350 TV 3 28 70 22 Heavy duty anchor 75 for cable vault inside depth in m Nominal size in mm Permitted load capacity in kg 1 1.80 1400 975 59.0141.00.00 2.10 1700 1175 59.0151.00.00 2.40 2000 1375 59.0161.00.00 2.70 2300 1575 59.0171.00.00 3.00 2600 1775 59.0181.00.00 Special lengths available upon request. 1 Concrete C20/25 1400 to 2600 1 Shaft wall concrete C20/25 13
Below-Surface Hardware Cable Vault and Junction Box Cable Support 80 System-compatible storage of cables and utility lines Permitted load capacity (distributed load) in combination with cable support rail 1000 N (+750N transient) PA6 GF30 210 Mounting into the cable support rail 80/20 80/30 Lock cotter 80/40 140 80/60 Lock cotter Cable support rail (KHS) Adjusting Position Horizontal locked standard position of the console will pivot by 45 each after lock cotter is removed. 45 Standard Position 45 Cable support (80/20) with cantilever bracket (hole Ø 13 mm) for wall mounting or mounting in cast-in channel Cable support for cable support rail Cable support for wall mounting / cast-in channel Size Length in mm Weight in kg 80/20 210 1.2 59.0901.00.00 80/30 310 1.7 59.0911.00.00 80/40 420 2.2 59.0041.00.00 80/60 600 3.0 59.0061.00.00 Size Length in mm Weight in kg 80/20 210 1.2 59.0902.00.00 80/30 310 1.7 59.0912.00.00 80/40 420 2.2 59.0042.00.00 80/60 600 3.0 59.0062.00.00 14
Below-Surface Hardware Cable Vault and Junction Box Sleeve Support Tray 95 and Cantilever Bracket Placement of sleeves in cable vaults Load per unit area (95/60) 400 N min. (1000 N transient) Cantilever brackets including cotter pin (DIN 11024) for cable support rails 95/40 Stainless Steel Adjusting Position Infinitely variable sleeve support tray Cotter pin 95/60 Cantilever bracket Cable support rail 760 to 1100 mm Sleeve joint e.g. with tightening straps Complete sleeve support tray Sleeve support tray Number of trays Number of cantilever brackets Supporting surface width x depth in mm 95 1 760 to 1100 x 200 59.1700.00.00 95/40 2 2 760 to 1100 x 400 59.2108.00.00 95/60 3 2 760 to 1100 x 600 59.2109.00.00 Cantilever bracket (includes cotter pin DIN 11024) for cable support rail Size Installation depth in mm (about) 20 250 59.1700.03.00 40 450 59.1700.01.00 60 650 59.1700.02.00 15
Below-Surface Hardware Cable Vault and Junction Box Extendible Shaft Ladder Two-piece (upper and lower ladder section), attached to ladder hoop Shaft ladder 180/55 Size Shaft ladder: 180/55 59.1812.00.00 Shaft ladder: 180/85 59.2065.00.00 Shaft ladder: 210/55 59.2066.00.00 Upper / lower ladder Steps Lower ladder 180 5 59.1812.01.00 Lower ladder 210 6 59.1896.01.00 Upper ladder 55 4 59.1812.02.00 Upper ladder 85 5 59.1896.02.00 Manhole ring height 55 cm Upper ladder Ladder hoop Mounting and fixing the lower ladder to the ladder hoop Clear shaft depth 180 cm Lower ladder 68 to 75 395 Shaft wall Ladder Hoop Extendible for Shaft Ladder 495 Bracket for hooking the lower ladder Ladder hoop ø 18 100 89 includes 2x bolt M12x70 DIN 571, washer 13 DIN 9021 and plugs14 59.1812.03.00 16
Below-Surface Hardware Cable Vault and Junction Box Large Shaft Ladder Climbing aid Rungs Stringer length in mm 2 560 59.2164.00.00 3 840 59.2165.00.00 4 1120 59.2166.00.00 5 1400 59.2167.00.00 6 1680 59.2168.00.00 7 1960 59.2169.00.00 8 2240 59.2170.00.00 9 2520 59.2171.00.00 10 2800 59.2172.00.00 Shaft ladder 10 rungs Wall anchor 2800 345 Mounting and Accessories for Straight Shaft Ladder Mounting shaft ladder to shaft wall and floor Floor mounting Shaft wall Article Wall anchor complete (includes 4x washer A13 DIN125, 2x washer 13 DIN9021, 2x bolt M12x60 DIN933, 2x nut M12 DIN934, 2x screw 12x70 DIN571, 2x plug S14) Complete floor mounting set (includes 4x washer 13 DIN125, 4x screw 12x70 DIN571, 4x plug S14) 59.2164.02.00 59.2164.01.00 Wall anchor Floor mounting Climbing aid with support handle retraction (5 rungs or more) 59.2164.10.00 Climbing aid 17
Below-Surface Hardware Cable Vault and Junction Box Mobile Ladder Guard (Adjustable) Ladder guard for vertical insertion of standard store-bought ladders (width: 350 bis 385 mm, stringer depth 70 mm) Shaft ladder Article Mobile ladder guard 59.2224.00.00 min. 1 m Locking pin max. 300 Handle Adapter (Suspension bracket) Valve (Stowing and securing ladder) Clamping lever for adjusting angle (5 to 15 ) 5 m max. Adapter for Mobile Ladder Guard Suspension bracket for holding the mobile ladder guard Adapter for Mobile Ladder Guard Suspension bracket, includes 2x hexagon bolt M10x70 DIN 571, 2x washer 10,5 DIN 125, 2x plug S12 59.2224.01.00 Hooking the mobile ladder guard into the suspension bracket Shaft wall 18
Below-Surface Hardware Cable Vault and Junction Box Dirt Collecting Tray 86 Protects junction box structures against dirt and rainwater Held by cantilever brackets that hook into the dedicated support recesses in the shaft wall, or else by tool yokes High rigidity, with spillover of grey water during removal being prevented by ribbed design Cantilever bracket PP GF 735 (width of tool yoke B) 73 Cantilever brackets PP GF 200 320 350 440 Junction box (70 x 40 cm) 625 Support recess Article Weight in kg Dirt collecting tray 86 with 4 cantilever brackets 1.3 59.0341.00.00 Dirt Collecting Tray 87 Protects cable vault structures against dirt and rainwater Hooks into the dedicated support recesses in the shaft wall or held by tool yokes 735 (width of tool yoke B) 695 (width of tool yoke A) 677 (width of tool yoke C) 280 Cable vault (140 x 70 cm) Support recess 585 Article Weight in kg Dirt collecting tray 87 3.2 59.0521.00.00 19
Below-Surface Hardware Cable Vault and Junction Box Tool Yoke Storage and lifting aid for dirt collecting trays Dirt collecting tray 123.5 Model A 695 143.5 Model B 735 114.5 Model C 18 677 55 234 Support Model D Cable vault or junction box (AzK) 737 Model AzK (junction box) 435 255 20 Model straight 430 Tool Yoke Length in mm Model A 695 59.0211.00.00 Model B 735 59.0221.00.00 Model C 677 59.0201.00.00 Model D 737 59.0231.00.00 Model E 785 59.0351.00.00 Model AzK 435 59.0931.00.00 Model straight 430 59.0481.00.00 20
Below-Surface Hardware Bushings Wall Bushing MD 1 and MD 2 Wall thickness 480 max. Insulation coat Gas- and water-proof channelling of cables through masonry Heat-shrinkable polyethylene hose with integrated support spiral Adhesive exterior coating for dense bonding with concrete, cement or mortar Resistant against aliphatic and hydroaromatic hydrocarbons, ground salts and soil alkalines Overhanging shrinkable hose-ends with hot-melt adhesive inner lining Three drill hole calibres as counter support (2x fixed to MD) for the cement mortar to be inserted If the wall thickness exceeds 480 mm, several wall bushings may be gathered into one. Wall Marker ring Cable clip Cement mortar Drill hole calibre min. 80 Ground min. 80 about 800 fixed fixed flexible Wall exterior Pipe / cable 2 1 3 without support spiral shrunk-to-fit MD for wall thickness >480 mm Wall bushing for cable/ pipe ø in mm max. wall thickness in mm Minimum drill hole ø in mm Pieces MD 1 8 to 14 480 40 100 59.0501.00.00 MD 2 10 to 26 480 55 60 59.0511.00.00 MD 50-3F (3x) 8 to 14 (1x) KKR DN50 480 70 1 59.0571.00.00 Sealant max. ø 26 Sealant made of non-setting sealing compound for inserting two cables into an MD 2 wall bushing MD 2 Cable 1 Cable 2 for wall bushing Number required MD 2 2 59.1415.00.00 Sealant 21
Cable Ducts and Protective Cable Conduits Below-Surface Hardware Spacer HDPE Facilitates setting up pipe assemblies and ensures a constant gap of 30 mm between the pipes Prevents lateral protrusion of pipes during future excavating work next to the pipe assembly Horizontally or vertically parallel installation of any number of pipes High rigidity for secure routing even with narrow-curving radii Separation option for Spacer 50/10 in 2- or 3-strain pipe lines Recommended interval between spacers 1.5 m 110/4 110/6 110/8 281.5 421 560.5 20 ø 109.5 147 100 188 30 50/3-110/2 50/10 281.5 402.5 Installation example (plan view) 1.5 m ø 49.7 30 110/8 Separating line Spacer for cable duct pipe (KKR) Pieces 110/4 4x DN110 50 59.1401.00.00 110/6 6x DN110 50 59.1402.00.00 110/8 8x DN110 50 59.1403.00.00 50/3-110/2 3x DN50 + 2x DN110 50 59.1400.00.00 50/10 10x DN50 50 59.1420.00.00 110/6 DN110 Belt Clamp for Cable Duct Half-Pipe Sleeve 20 Stainless Steel M6x20 DIN933 for DN110 59.0071.00.00 DN50 59.0081.00.00 Cable duct half-pipe Belt clamp Cable duct half-pipe sleeve ø 53,5 (DN50) ø 115 (DN110) 22
Below-Surface Hardware Earth Rod Ground level Earth Rod and Pipe Earth Rod For installing earthing systems Optimised earthing to meet seasonal weather fluctuations through autonomously constant earth electrode resistance Earthing band inserted from above Driving stud for earth rod Ø 26.9 x 2.9 20 to 60 cm 108 Earthing band 30 x 3.5 mm laterally inserted Pipe earth rod 30 1500 Earth rod connecting clamp Round earth ø 8 Earth rod ø 25 Earth rod ø 25 125 1500 Separate parts Earth rod tip Earth rod 59.1416.00.00 Earth rod tip (strike point) 59.1416.00.03 Earth rod terminal clamp (for connecting earth rod and steel bands or rods) 59.1417.00.00 Pipe earth rod 59.1648.00.00 Pipe earth rod tip (driving point) Pipe earth rod terminal clamp (upon request) (upon request) Driving head for manual driving for earth rod 59.1416.00.05 May be extended by coupling for pipe earth rod (upon request) 23
Contact Berthold Sichert GmbH Kitzingstr. 1-5 D-12277 Berlin Key Account Consulting Tel.: +49 30 74707-0 Fax.: +49 30 74707-20 E-mail: Office@Sichert.com Caroline von Papen Caroline.Papen@Sichert.com All of the information provided here is correct and reliable to the best of our knowledge. The information does not, however, warrant any characteristics. Any user of our products is solely responsible to assess whether our products suit the user's intended purpose. Our product warranty is exclusively limited to the terms and conditions of sale, delivery and payment. In no case will we be liable for incidental, indirect damage and collateral damage resulting from the same. Status: 9. October 2012, 3:17 PM/nee.