RAISED FLOOR SYSTEM IB FLOOR 2017
IB FLOOR LIST Type Specification Size (mm) FFH (mm) Concentrated Load Uniform Load N/m 2 500mm x 50mm Steel Panel 600mm x 600mm Steel Panel 600mm x 600mm Aluminum Panel 1
Content OA503 OA505 3000N 5000N Steel 3-4 OA603 OA65 3000N 5000N Steel 3-4 HPL 603/605 3000N HPL & Steel 5-6 PVC 603/605 3000N PVC & Steel 5-6 Ceramic 603 3000N Ceramic & Steel 5-6 Al603 3000N Aluminum 7-8 Die-cast Al605 5000N Aluminum 7-8 Die-cast Al609 9000N Aluminum 7-8 Die-cast 2
RAISED FLOOR SYSTMES Bare Steel Raised Floor OA600 and OA500 OA503 / 505 H70-1000 Top Plate using SPCC cold rolled steel, Bottom Plate using ST14 Steel for stretch, after automatic spot welding, environmental friendly oil treatment, wear resistant Epoxy Coating, the panel is infilled with foamed cement. Each panel had 4 corner lock holes. 36 egg crate stretches and 16 embossments increasing the loading performance in the center of the panel. Embossments points Reinforcement Rib Loading Chart Unique Reinforcement Cross Rib Option Item Wider Foamed cement Edge Design Top steel sheet Bottom steel sheet OA603 / 605 H70-1000 Top plate using SPCC cold rolled steel, bottom plate using ST14 steel for stretch, after automatic spot welding, environmental friendly oil treatment, wear resistant epoxy coating, the panel is infilled with foamed cement. Each panel has 4 corner lock holes. 1. All steel component, excellent loading capacity and fire-resistance. 2. Cross rib and wide bottom board design, improves panel loading capacity. 3. Precise panel size, interchangeable with each panel 4. Small size panel, low unit weight less total pressure to building, convenient in installation and maintenance. 5. Dark-grey epoxy coating, hard wearing and anti-corrosive Loading Chart Three vertical and horizontal reinforcement ribs Embossments points Wider edge and rib Bottom steel Foamed Cement Top steel 3 Aluminum Head Pedestal Perimeter Pedestal Round Tube Pedestal Square Tube Pedestal
Section Detail RAISED FLOOR 500X500mm Section Detail Wall Wall Border Pedestal OA500 Panel Aluminum Head Pedestal 500 RAISED FLOOR 600X600mm Section Detail Wall Wall Cut Panel Panel Finsh Gasket ESD600 Panel Pedestal Stringer Stringer Lockng Screw FFH 600 4
600mm Anti-Static HPL/PVC Steel Cementitious Floor HPL/PVC603, HPL/PVL605 Top Plate using SPCC cold rolled steel, Bottom Plate using ST14 Steel for stretch, after automatic spot welding, environmental friendly oil treatment, wear resistant Epoxy Coating, the panel is infilled with foamed cement. Panel surface has wear-resistance and anti-static HPL/PVC, can be gravity laid into the infrastructure formed by pedestals, stringers and screws. 1. All steel components, Great Mechanical Performance. 2. Heavy loading performance and excellent fire-rate. 3. Special and scientifical design of diamond stretch, wider bottom edge board, reinforcement rib etc, imporove panel loading performance. 4. Precise dimension, great interchangeability. 5. Light-Grey Epoxy coating, hard wearing and anti-corrosive. Loading Chart Ceramic 603 Ceramic 600 Top plate using SPCC cold rolled steel,bottom plate using ST14 Steel for strech, after automatic spot welding, environmental friendly oil treatment, wear resistant Epoxy Coating,the panel is infilled with foamed cement. Continuous reinforcement rib Diamond stretchings Reinforcement concave Reinforcement embosement ST-14steel Edge trim Covering material SPCC steel High quality foaming cement Loading Chart Panel Cut View 45mm Bottom Steel Pate PVC edge trim Top Steel Pate Ceramic Cement 5
Covering Material A Comprehensive selection of NAKA covering materials are available including more colors of HPL, PVC andother interior finishes, to satisfy customer s different requirements. Please contact with us if you want other covering material which is not listed below. Anti-Static HPL HPL2010 HPL2010-1 HPL2010-2 HPL2010-3 HPL2010-4 HPL2010-5 HPL2010-6 HPL2103 HPL2158 Conductive PVC PVC-1101 PVC-1103 PVC-01 PVC-04 PVC-06 PVC-901 PVC-903 PVC-904 PVC-905 PVC-906 PVC-909 PVC-9022 Ceramic Tile CT-01 CT-02 CT-03 CT-04 CT-05 6
Die-casting Aluminum Raised Access Floor Die-casting Aluminum Solid Panel Structure Aluminum shied panel is die-casted by pure aluminum ingot. It is anti-corrosion and high strength. This panel can be epoxy powder coated or nickel chrome plated. Both finish makes the panel gentle glow, anti-corrosion and anti-wear. Feature New original design with high dimension accuracy. Light weight, high density and good loading capacity Waterproof, fireproof, anti-corrosion, anti-magnetic, environment friendly and non-radiation. Stable structure and never deflects, good conductivity. Recycleable and economical Loading Chart Grating Panel Solid Panel 7
Die-casting Aluminum Raised Access Floor Die-casting Aluminum Perforated Panel (10~15%) Feature Aluminum Perforated panel is the industry s only air flow panel that allows adjustment in thickness to sit flush with the adjacent solid panels. The MAP Series has a free area of 10%~25% and comes with or without sliding dampers. Die-casting Aluminum Grating Panel (50%) Feature 50% Aluminum Grating panel is widely used in clean rooms (e.g. top class air clean laboratory, semi-conductor workshops and operation rooms in hospital.) Aluminium air floor panel (55%) bottom Feature This aluminum panel is designed to take heavy load and ventilation rate is as high as 55%. Sliding damper can be installed to the bottom the panel to meet air flow rate requirement of 0-55%. This panel could be installed with any of Naka anti-static steel raised floor, anti-static calcium sulphate raised floor, high-density woodcore raised floor and aluminum raised floor. 8
Accessories for Raised Access Floor Accessories for Raised Access Floor Floor Box G01 G02 G03 (210 x 130) (210 x 130) (145 x 145) G04 G05 G06 (250 x 220) (250 x 220) (250 x 220) Accessories for Raised Access Floor Single Cup Panel Lifter Double Cup Panel Lifter 9
Floor Installation Instruction Clean the ground Draw gridding line Put the pedestal Install the floor Seal the side Clean the surface of floor 10
www.naka-kogyo.co.jp JAPAN (HEAD OFFICE) 3/F, Nihon Seimei Ueno Building, 2-18-10, Higashi Ueno, Taito-ku, Tokyo,110-0015 Japan. Tel : +81-3-5817 7410 Fax : +81-3-5817 7420 SINGAPORE 60 Albert Street, #08-11, OG Albert Complex, Singapore 189969. Tel : +65 6635 3393 Fax : +65 6635 3398 HONG KONG No.2 G/F, Wah Wai Centre, 38-40 Au Pui Wan Street, Fo Tan, N.T., Hong Kong. Tel : +852 2566 8018 Fax : +852 2512 8278 SHANGHAI Room 1020, Pine City Hotel Shanghai, 777 Zao Jia Bang Road, Shanghai, China. Tel : +86-21-6443 7239 Fax : +86-21-6443 0237