Kestro Engineering Plastic For Home Appliances 201109, Shanghai, China Tel: +86-21-6490-7268; Fax: +86-21-6490-7270 YEDPA G Caddesi No:79, Atasehir 34779 Istanbul Turkey Tel: +90-216-661-6611; Fax: +90-216-661-6612 info@globetz.com Washing Machine Dish Washer Refrigerator Oven Shanghai HongKong Guangzhou Kunshan Istanbul 1 appliancesolutions TM Our Expertise, Your value
is a specialty compounder that combines superior technical ability (5elem-solutions ) with unmatched customer services to provide our customers with state-of-the-art engineering polymer resins and services. We provide quotes and material quickly and accurately to meet the most stringent specifications while using high quality materials. Kestro Polychem works closely with top material manufactures and utilizes our in house labs to assure the best possible feedstocks and additives for our customers. Our goal is to provide the unmatched customer service and products in the world plastics industry. Kestro engineering thermoplastics are designed to various applications such as home appliance, automobile and electric industry. With many years of experience in engineering plastic industry, Kestro research team has been focusing on to build up superior technologies used in home appliances. Our appliancesolutions TM make Kestro to be able to serve the most famous appliance customers globally. appliancesolutions TM -- Find internal beauty at your kitchen 2
Washing Machine Typical parts vs Kestro grades Detergent Dispenser Panel PCB Holder ElePP B308HR ElePP B308HR G-flam C300NH Inlet Valve Elemid A360HR Elester D360F560 Elemid A370HS Elemid A370F3 Elemid B300F6 Motor Elemid A370F170 Elester D360F560 Elemid A370F170 Elester D360F560 Tub Drain Pump G-flam C300NH G-flam C300NH108 ElePP B308DR 3
Grade Characteristics Application G-flam C300NH Drain Pump Cover PCB Holder (PP-FR) Halogen-free, low density, conform to IEC 60335-1 4 th TDS Page 5 G-flam C300NH108 (PP-FR) TDS Page 6 Eco-friendly, low density, cost-effectively Bobbins ElePP B308HR (PP-T40) Water resistant, aging resistant, detergent resistant Tub, Detergent Dispenser, Panel TDS Page 7 ElePP B308DR (PP-K40) Water resistant, aging resistant, detergent resistant Tub, Detergent Dispenser, Panel TDS Page 8 Elemid A370F170 (PA66-GF35) TDS Page 9 Eco-friendly flame retardant, UL94 V0 Motor Elemid A360HR (PA66-GF30) TDS Page 10 Water resistant, aging resistant Inlet Valve cover Elemid B300F6 (PA6-FR) TDS Page 11 Unfilled, halogen & phosphorus free, UL94 V-0 (0.8mm) Coil Elemid A370F3 (PA66-GF35-FR) TDS Page 12 Halogen-free, UL94 V0 Coil Elemid A370HS (PA66-GF35) TDS Page 13 35% reinforced PA66 Coil Elester D360F560 (PBT-GF30-FR) TDS Page 14 Halogen & red phosphorus-free, light colorable; Outstanding mechanical and electrical properties. Valve Part Motor cover Motor cover Remarks: 1) These pictures are only used for your reference to indicate the parts that our material is used for. 2) The names of the parts may different from one customer to another, so the names here are also used just as references. 3) If you can t locate the material from either the picture or the name of the part, or you have a part that is not listing here, please consult with our technical expert to locate the grade of our material that best matches your part. 4
G-flam C300NH >PP-FR< Non-halogen, Low density, Fulfill with IEC 603354th E&E,Home appliance ect. Density ISO 1183 1 g/cm 3 Melt Volume Rate(MVR) Mold shrinkage Thermal Properties Melt Temperature Tensile strength Flexural Strength Charpy Impact Strength Charp Impact Strength(Notched) Flammability Glow Wire Flammability Index(GWFI) Glow Wire Ignition Temperature(GWIT) ISO 1133 5 cm 3 /10min Parallel(24h) 5Elem 0.8~1.0 % Normal(24h) 5Elem 0.8~1.0 % 10 C/min DSC 167 C Ⅰtype, 50mm/min ISO 527 26 MPa Ⅰtype, 50mm/min ISO 527 5 % 2mm/min ISO 178 35 MPa 2mm/min ISO 178 2100 MPa 1eU type ISO 179 38 kj/m 2 1eU type ISO 179 4 kj/m 2 1.6mm UL 94 V0 -- 2.0mm IEC 60695-2-12 960 2.0mm IEC 60695-2-13 775 All values are measured at least after 48 hours storage at 23 C,50%RH. Values shown are based on testing of injection moulded laboratory test specimens. Unless specified to the contrary, the values given have been established on standardized test specimens at room temperature. The figures should be regarded as guide values only and not as binding minimum values. Please note that, under certain conditions, the properties can be affected to a considerable extent by the design of the mold/die, the processing conditions and coloring. Flammability results are based on small-scale laboratory tests for purposes of relative comparison and are not intended to reflect the hazards presented by this or any other material under actual fire conditions. Each user is responsible for making its own determination as to the suitability of seller s products, services or recommendations for the user s particular use through appropriate end-use testing and analysis. This information and our technical advice-whether verbal, in writing or by the way of trial are given in good faith but without warranty, and this also applies where proprietary rights of third parties are involved. Shanghai, China: 5 Kestro-TDS-ETP-G-flam C300NH
G-flam C300NH108 Density Melt Volume Rate(MVR) Mold shrinkage Thermal Properties Melt Temperature Tensile strength Flexural Strength Charpy Impact Strength >PP-FR< Enviromental Friendly,Low Density,Aging resistance E&E,Home appliance ect. ISO 1183 0.93 g/cm 3 ISO 1133 12 cm 3 /10min Parallel(24h) 5Elem 1.2~1.5 % Normal(24h) 5Elem 1.2~1.5 % 10 C/min DSC 167 C Ⅰtype, 50mm/min ISO 527 32 MPa Ⅰtype, 50mm/min ISO 527 30 % 2mm/min ISO 178 36 MPa 2mm/min ISO 178 1800 MPa 1eU type ISO 179 4J NB kj/m 2 Charp Impact Strength(Notched) 1eU type ISO 179 6 kj/m 2 Flammability Glow Wire Flammability Index(GWFI) 1.6mm UL 94 V0 -- 2.0mm IEC 60695-2-12 960 All values are measured at least after 48 hours storage at 23 C,50%RH. Values shown are based on testing of injection moulded laboratory test specimens. Unless specified to the contrary, the values given have been established on standardized test specimens at room temperature. The figures should be regarded as guide values only and not as binding minimum values. Please note that, under certain conditions, the properties can be affected to a considerable extent by the design of the mold/die, the processing conditions and coloring. Flammability results are based on small-scale laboratory tests for purposes of relative comparison and are not intended to reflect the hazards presented by this or any other material under actual fire conditions. Each user is responsible for making its own determination as to the suitability of seller s products, services or recommendations for the user s particular use through appropriate enduse testing and analysis. This information and our technical advice-whether verbal, in writing or by the way of trial are given in good faith but without warranty, and this also applies where proprietary rights of third parties are involved. Shanghai, China: 6 Kestro-TDS-ETP-G-flam C300NH108
ElePP B308HR >PP-T40< Good Chemical Resistance; Good Detergemt Resistance; Good Thermal Aging; Home appliance ect. Density ISO 1183 1.22 g/cm 3 Melt Volume Rate(MVR) Thermal Properties Heat Deflection Temperature(HDT) Tensile strength Flexural Strength Charpy Impact Strength Charp Impact Strength(Notched) ISO 1133 12 cm 3 /10min 1.82MPa ISO 75-2 81 C Ⅰtype, 50mm/min ISO 527 33 MPa Ⅰtype, 50mm/min ISO 527 7 % 2mm/min ISO 178 55 MPa 2mm/min ISO 178 4000 MPa 1eU type ISO 179 25 kj/m 2 1eU type ISO 179 4 kj/m 2 Flammability 1.6mm UL 94 HB -- All values are measured at least after 48 hours storage at 23 C,50%RH. Values shown are based on testing of injection moulded laboratory test specimens. Unless specified to the contrary, the values given have been established on standardized test specimens at room temperature. The figures should be regarded as guide values only and not as binding minimum values. Please note that, under certain conditions, the properties can be affected to a considerable extent by the design of the mold/die, the processing conditions and coloring. Flammability results are based on small-scale laboratory tests for purposes of relative comparison and are not intended to reflect the hazards presented by this or any other material under actual fire conditions. Each user is responsible for making its own determination as to the suitability of seller s products, services or recommendations for the user s particular use through appropriate end-use testing and analysis. This information and our technical advice-whether verbal, in writing or by the way of trial are given in good faith but without warranty, and this also applies where proprietary rights of third parties are involved. Shanghai, China: 7 Kestro-TDS-ETP-ElePP B308HR
ElePP B308DR >PP-K40< Resistance to Detergent & Hot Water,Low Water Absorption,High ; Home Appliances,Wash Tank,Washing Machine Special; Density ISO 1183 1.24 g/cm 3 Melt Volume Rate 230 C,2.16Kg ISO 1133 8 cm 3 /10min Thermal Properties Heat Deflection Temperature 1.82MPa ISO 75-2 65 C Vicat Softening Temperature 5kg ISO 306 95 C Tensile strength Ⅰtype, 50mm/min ISO 527 24 MPa Strain at Field Ⅰtype, 50mm/min ISO 527 3.5 % Flexural Strength 2mm/min ISO 178 35 MPa 2mm/min ISO 178 2200 MPa Izod Impact Strength 1eU type ISO 180 40 kj/m 2 Izod Impact Strength(Notched) 1eU type ISO 180 3.5 kj/m 2 All values are measured at least after 48 hours storae at 23 C,50%RH. Values shown are based on testing of injection moulded laboratory test specimens. Unless specified to the contrary, the values given have been established on standardized test specimens at room temperature. The figures should be regarded as guide values only and not as binding minimum values. Please note that, under certain conditions, the properties can be affected to a considerable extent by the design of the mold/die, the processing conditions and coloring. Flammability results are based on smallscale laboratory tests for purposes of relative comparison and are not intended to reflect the hazards presented by this or any other material under actual fire conditions. Each user is responsible for making its own determination as to the suitability of seller s products, services or recommendations for the user s particular use through appropriate end-use testing and analysis. This information and our technical advice-whether verbal, in writing or by the way of trial are given in good faith but without warranty, and this also applies where proprietary rights of third parties are involved. 该文件中的某些信息来自运用小型设备的实验室检测, 这些信息可能无法可靠指明使用大型设备时得到的性能或指标 典型 数值或者没有给出范围的数值不能表明最小或者最大性能 加工条件和配色可能会导致材料性能背离该文件中给出的数值 五行公司对于该文件中内容的准确性 适用性或者使用该文件的内容后产生的后果不做出任何保证 您有责任进行全面的终端产品性能测试, 以便确定该公司的产品是否适用于您的应用工艺, 同时您要考虑到您适用本文件以及使用该产品可能导致的所有风险和责任 Shanghai, China: 8 Kestro-TDS-ETP-ElePP B308DR
Elemid A370F170 Density Water Absorption Melt Volume Rate(MVR) Thermal Properties Heat Deflection Temperature(HDT) Stress at Break Flexural Strength Charpy Impact Strength Charp Impact Strength(Notched) Flammability Glow Wire Flammability Index(GWFI) Glow Wire Ignition Temperature(GWIT) Electrical Properties CTI >PA6-GF35-FR< ECO-Friendly flame retardance, outstanding mechanical and electrical properties./ E&E Market,Electrical coomponents./ ISO 1183 1.6 g/cm 3 23 C, 50%RH ISO 15512 0.7 % 275 C,5Kg ISO 1133 65 cm 3 /10min 1.82MPa ISO 75-2 230 C Ⅰtype, 50mm/min ISO 527 120 90 MPa Ⅰtype, 50mm/min ISO 527 2.1 4 % 2mm/min ISO 178 200 MPa 2mm/min ISO 178 9000 MPa 1eU type ISO 179 42 48 kj/m 2 1eU type ISO 179 9 14 kj/m 2 1.6mm UL 94 V-0 -- 2.0mm IEC 60695-2-12 960 2.0mm IEC 60695-2-13 800 Solution A IEC 60112 250 V All values are measured at least after 48 hours storage at 23 C,50%RH. Values shown are based on testing of injection moulded laboratory test specimens. Unless specified to the contrary, the values given have been established on standardized test specimens at room temperature. The figures should be regarded as guide values only and not as binding minimum values. Please note that, under certain conditions, the properties can be affected to a considerable extent by the design of the mold/die, the processing conditions and coloring. Flammability results are based on small-scale laboratory tests for purposes of relative comparison and are not intended to reflect the hazards presented by this or any other material under actual fire conditions. Each user is responsible for making its own determination as to the suitability of seller s products, services or recommendations for the user s particular use through appropriate end-use testing and analysis. This information and our technical advice-whether verbal, in writing or by the way of trial are given in good faith but without warranty, and this also applies where proprietary rights of third parties are involved. Shanghai, China: 9 Kestro-TDS-ETP-Elemid A370F170
Elemid A360HR Application Density ISO 1183 1.36 g/cm 3 Water Absorption Mold shrinkage Thermal Properties Injection grade 23 C, 50%RH (Equiilibrium) ISO 15512 1.9 % Parallel(24h) 5Elem 0.4 % Normal(24h) 5Elem 0.7 % Melt Temperature 10 C/min DSC 260 C 1.82MPa ISO 75-2 245 C Heat Deflection Temperature(HDT) 0.455MPa 250 C Tensile strength Flexural Strength Charp Impact Strength Charp Impact Strength(Notched) >PA6.6-GF30< Heat stabilized, improved hydrolysis resistance Ⅰtype, 50mm/min ISO 527 170 MPa Ⅰtype, 50mm/min ISO 527 2 % 2mm/min ISO 178 250 MPa 2mm/min ISO 178 8500 MPa 1eU type ISO 179 80 kj/m 2 1eU type ISO 179 13 kj/m 2 Flammability 1.6mm UL 94 HB -- Burning Rate FMVSS.302 <50 mm/min All values are measured at least after 48 hours storage at 23 C,50%RH. Values shown are based on testing of injection moulded laboratory test specimens. Unless specified to the contrary, the values given have been established on standardized test specimens at room temperature. The figures should be regarded as guide values only and not as binding minimum values. Please note that, under certain conditions, the properties can be affected to a considerable extent by the design of the mold/die, the processing conditions and coloring. Flammability results are based on small-scale laboratory tests for purposes of relative comparison and are not intended to reflect the hazards presented by this or any other material under actual fire conditions. Each user is responsible for making its own determination as to the suitability of seller s products, services or recommendations for the user s particular use through appropriate end-use testing and analysis. This information and our technical advice-whether verbal, in writing or by the way of trial are given in good faith but without warranty, and this also applies where proprietary rights of third parties are involved. Shanghai, China: 10 Kestro-TDS-Elemid A360HR
Elemid B300F6 >PA6-FR< Unfilled,Halogen&phosphorus-free, UL94 V-0 (0.8mm) E&E Market,ect. Density Water Absorption Melt Volume Rate(MVR) Mold shrinkage Thermal Properties Melt Temperature Tensile Strength Flexural Strength Charpy Impact Strength Charp Impact Strength(Notched) Flammability Glow Wire Ignition Temperature(GWIT) Electrical Properties Volume Resistivity CTI 23 C, 50%RH (Saturation) ISO 1183 1.18 g/cm 3 ISO 15512 2.6 % ISO 1133 15 cm 3 /10min Parallel(24h) 5Elem 1 % Normal(24h) 5Elem 1 % 10 C/min DSC 220 C Ⅰtype, 5mm/min ISO 527 70 MPa Ⅰtype, 5mm/min ISO 527 7 % 2mm/min ISO 178 105 MPa 2mm/min ISO 178 3100 MPa 1eU type ISO 179 65 kj/m 2 1eU type ISO 179 6 kj/m 2 0.8mm UL 94 V-0 -- 2.0mm IEC 60695-2-13 960 IEC 60093 1.00E+14 1.00E+11 Ω*cm Solution A IEC 60112 600 V All values are measured at least after 48 hours storage at 23 C,50%RH. Values shown are based on testing of injection moulded laboratory test specimens. Unless specified to the contrary, the values given have been established on standardized test specimens at room temperature. The figures should be regarded as guide values only and not as binding minimum values. Please note that, under certain conditions, the properties can be affected to a considerable extent by the design of the mold/die, the processing conditions and coloring. Flammability results are based on small-scale laboratory tests for purposes of relative comparison and are not intended to reflect the hazards presented by this or any other material under actual fire conditions. Each user is responsible for making its own determination as to the suitability of seller s products, services or recommendations for the user s particular use through appropriate end-use testing and analysis. This information and our technical advice-whether verbal, in writing or by the way of trial are given in good faith but without warranty, and this also applies where proprietary rights of third parties are involved. Shanghai, China: 11 Kestro-TDS-ETP-Elemid B300F6
Elemid A370F3 >PA66-GF35-FR< 35%GF reinforced PA66. halogen-free, UL94 V-0 E&E Market,for electric connector. Density Water Absorption Melt Volume Rate Thermal Properties Melt Temperature Heat Deflection Temperature Tensile strength Flexural Strengh Charpy Impact Strength Charp Impact Streng(Notched) Flammability Glow Wire Flammability Index Electrical Properties Volume Resistivity All values are measured at least after 48 hours storae at 23 C,50%RH. 23 C, 50%RH (Saturation) ISO 1183 1.45 g/cm 3 ISO 15512 1.20E+00 % 275 C,5Kg ISO 1133 3.00E+01 cm 3 /10m in 10 C/min DSC 2.60E+02 C 1.82MPa ISO 75-2 2.50E+02 C 0.455MPa 2.55E+02 C Ⅰtype, 50mm/min ISO 527 1.30E+02 MPa Ⅰtype, 50mm/min ISO 527 4.00E+00 % 2mm/min ISO 178 1.85E+02 MPa 2mm/min ISO 178 9.00E+03 MPa 1eU type ISO 179 6.50E+01 kj/m 2 1eU type ISO 179 1.40E+01 kj/m 2 1.6mm UL 94 V-0 -- 2.0mm IEC 60695-2-12 9.60E+02 IEC 60093 1.00E+13 1.00E+10 Ω*cm Values shown are based on testing of injection moulded laboratory test specimens. Unless specified to the contrary, the values given have been established on standardized test specimens at room temperature. The figures should be regarded as guide values only and not as binding minimum values. Please note that, under certain conditions, the properties can be affected to a considerable extent by the design of the mold/die, the processing conditions and coloring. Flammability results are based on small-scale laboratory tests for purposes of relative comparison and are not intended to reflect the hazards presented by this or any other material under actual fire conditions. Each user is responsible for making its own determination as to the suitability of seller s products, services or recommendations for the user s particular use through appropriate end-use testing and analysis. This information and our technical advice-whether verbal, in writing or by the way of trial are given in good faith but without warranty, and this also applies where proprietary rights of third parties are involved. Shanghai, China: 12 Kestro-TDS-ETP-Elemid A370F3
Shanghai, China: 13 Kestro-TDS-ETP-Elemid A370HS
Product Descrption Elester D360F560 >PBT-GF30-FR< Density ISO 1183 1.52 g/cm 3 Water Absorption Melt Volume Rate(MVR) Mold shrinkage Tensile strength Flexural Strength Charpy Impact Strength Charp Impact Strength(Notched) Flammability Glow Wire Flammability Index(GWFI) Glow Wire Ignition Temperature(GWIT) Electrical Properties CTI Halogen-free,red phosphorus-free,light colorable;outstanding mechanical andelectrical properties. E&E,Home appliance ect. 23 C, 50%RH (Saturation) ISO 15512 1.1~1.5 % 300 C, 1.2Kg ISO 1133 20 cm 3 /10min Parallel(24h) 5Elem 0.3-0.6 % Normal(24h) 5Elem 0.3-0.6 % Ⅰtype, 50mm/min ISO 527 75 MPa Ⅰtype, 50mm/min ISO 527 1 % 2mm/min ISO 178 120 MPa 2mm/min ISO 178 7000 MPa 1eU type ISO 179 25 kj/m 2 1eU type ISO 179 6 kj/m 2 1.6mm UL 94 V0 -- 1.0mm IEC 60695-2-12 960 2.0mm IEC 60695-2-13 775 Solution A IEC 60112 600 V All values are measured at least after 48 hours storage at 23 C,50%RH. Values shown are based on testing of injection moulded laboratory test specimens. Unless specified to the contrary, the values given have been established on standardized test specimens at room temperature. The figures should be regarded as guide values only and not as binding minimum values. Please note that, under certain conditions, the properties can be affected to a considerable extent by the design of the mold/die, the processing conditions and coloring. Flammability results are based on small-scale laboratory tests for purposes of relative comparison and are not intended to reflect the hazards presented by this or any other material under actual fire conditions. Each user is responsible for making its own determination as to the suitability of seller s products, services or recommendations for the user s particular use through appropriate end-use testing and analysis. This information and our technical advice-whether verbal, in writing or by the way of trial are given in good faith but without warranty, and this also applies where proprietary rights of third parties are involved. Shanghai, China: 14 Kestro-TDS-ETP-Elester D360F560