HT417/HT417H HAY TEDDER Published 05/12 PARTS MANUAL SECTION 17 MATERIAL HANDLING PARTS MANUAL An Operator s Manual was shipped with the equipment. The Operator s Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator s Manual is not with the equipment, contact your dealer or Bush Hog to obtain a copy before operating the equipment. Important Operating and Safety Instructions are found in the Mower Safety Video that can be instantly accessed on the internet at: www.algqr.com/bve
PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. For maximum safety and to guarantee optimum product reliability, always use genuine BUSH HOG Parts. The use of inferior replacement parts may causepremature or catastrophic failure which could result in serious injury or death.direct any questions regarding parts to: BUSH HOG 2501 Griffin Ave. Selma, AL 36703 www.bushhog.com Contact Us 800-304-2836 2009 Alamo Group Inc.
To the Owner/Operator/Dealer All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty RegistrationForm in full and return it to within 30 Days. Make certain the Serial Number of the Machine is recorded on thewarranty Card and on the Warranty Form that you retain.
LIMITED WARRANTY Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for non-commercial, state and municipalities use and ninety (90) days for commercial use from date of retail sale. The obligation of Bush Hog to the purchaser under this warranty is limited to the repair or replacement of defective parts. Replacement or repair parts installed in the equipment covered by this limited warranty are warranted for ninety (90) days from the date of purchase of such part or to the expiration of the applicable new equipment warranty period, whichever occurs later. Warranted parts shall be provided at no cost to the user at an authorized Bush Hog dealer during regular working hours. Bush Hog reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship. DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES Bush Hog s obligation under this limited warranty, to the extent allowed by law, is in lieu of all warranties, implied or expressed, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE and any liability for incidental and consequential damages with respect to the sale or use of the items warranted. Such incidental and consequential damages shall include but not be limited to: transportation charges other than normal freight charges; cost of installation other than cost approved by Bush Hog; duty; taxes; charges for normal service or adjustment; loss of crops or any other loss of income; rental of substitute equipment, expenses due to loss, damage, detention or delay in the delivery of equipment or parts resulting from acts beyond the control of Bush Hog. THIS LIMITED WARRANTY SHALL NOT APPLY: 1. To vendor items which carry their own warranties, such as engines, tires, and tubes. 2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident. 3. If parts not made or supplied by Bush Hog have been used in connection with the unit, if, in the sole judgement of Bush Hog such use affects its performance, stability or reliability. 4. If the unit has been altered or repaired outside of an authorized Bush Hog dealership in a manner which, in the sole judgement of Bush Hog, affects its performance, stability or reliability. 5. To normal maintenance service and normal replacement items such as gearbox lubricant, hydraulic fluid, worn blades, or to normal deterioration of such things as belts and exterior finish due to use or exposure. 6. To expendable or wear items such as teeth, chains, sprockets, belts, springs and any other items that in the company s sole judgement is a wear item. NO EMPLOYEE OR REPRESENTATIVE OF BUSH HOG IS AUTHORIZED TO CHANGE THIS LIMITED WARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE IN WRITING AND SIGNED BY BUSH HOG S SERVICE MANAGER, 2501 GRIFFIN AVE., SELMA, ALABAMA 36703. Record the model number, serial number and date purchased. This information will be helpful to your dealer if parts or service are required. MODEL NUMBER SERIAL NUMBER DATE OF RETAIL SALE MAKE CERTAIN THE WARRANTY HAS BEEN FILED WITH BUSH HOG SELMA, ALABAMA
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL MAY, 2012 ALPHABETICAL TABLE OF CONTENTS HT417/HT417H HAY TEDDER ITEM PAGE NUMBER NOTES..........................................................17-1-1 Axle Assembly..............................................17-1-2, 17-1-3 Axle Assembly 2.............................................17-1-4, 17-1-5 Decals - Bush Hog Marking.........................................17-1-16 Drawbar Assembly (Hydraulic Lift)...............................17-1-6, 17-1-7 Drawbar Assembly (Spring Lift).......................................17-1-11 Driveline Assembly...........................................17-1-8, 17-1-9 Gearbox Assembly................................................17-1-10 Hydraulic Cylinder & Hose Assembly...........................17-1-12, 17-1-13 Tire Assembly.............................................17-1-14, 17-1-15 Warranty................................................Inside Back Cover
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL APRIL, 2011 NOTES 17-1-1
AXLE ASSEMBLY MODELS HT417/HT417H (SPRING & HYDRAULIC LIFT) * ** * SPRING LIFT VERSION ONLY (QTY. 2) ** HYDRAULIC LIFT VERSION ONLY (QTY. 6) * 17-1-2
AXLE ASSEMBLY MODELS HT417/HT417H (SPRING & HYDRAULIC LIFT) REF. PART NO. NO. DESCRIPTION QTY. 1 3676403 Plate, Gearbox Lock 1 2 3676404 Shaft, Input Gearbox 1 3 3676400 Housing, Gearbox 1 4 3676449 RH Center Axle Housing 1 5 3676450 LH Center Axle Housing 1 6 3670275 Reinforcement Housing 1 7 3676451 RH Fork Support Housing 1 8 3676452 LH Fork Support Housing 1 9 3676453 Drive Shaft, Output 1 10 3676900 Gasket, Gearbox 2 11 3676421 Shaft, Rotor 2 12 3676454 Tine Disc 2 13 3676455 Hub, Gearbox 2 14 3676779 Plug (Spring Lift Version) 2 3676779 Plug (Hyd. Lift Version) 6 15 3676904 Shim 2 16 3676417 Joint, Double U- 2 17 3676424 Yoke 2 18 3676425 Kit, Cross & Bearing 4 19 3676426 Yoke, Center Double 2 20 3676427 Yoke, Splined 2 21 --------- Guard, Plastic Shaft 1 22 3676778 Guard, IID Protection 1 23 3676800 Seal, Oil 35 x 52 x 10 1 24 00766021 Ring E35 UNI 7435 1 26 00764417 Bearing, Ball 1-1.77 ID x 3.346 OD 1 27 3676407 Plug, Gearbox Oil 2 28 3676802 Seal, Oil 30 x 62 x 10 1 29 3236004 Ball Bearing, 30 x 62 x 16 W/O Seal 2 30 3676801 Seal, Oil 30 x 56 x 10 1 31 3636003 Bearing, Ball Two Rubber Seals 2 32 00754459 Bearing, 35 x 72 x 17 5 33 3676405 Gear, Pinion 1 34 3676408 Gear, Crown 1 35 3676419 Gear, Pinion 2 36 3676456 Crown Gear 2 37 703616W Roll Pin, M10 x 55 2 38 703417W Roll Pin, M6 x 55 2 39 001465 Grease Fitting, Straight, M6 2 40 00766457 Grease Fitting M10 x 1.5 Str PG 2 41 710640 Key, Rnd End 8 x 7 x 40 2 42 710630 Rnd End Key 8 x 7 x 30 MM 2 43 3678401 Bolt, Stud M8 x 1.25 x 30 Gr 8.8 2 44 00755934 Nut, M8 x 1.25 2 45 70093C Locknut, Toplock M8 x 1.25 2 46 02958784 Bolt Metric M8 x 1.25 x 20 Gr 8.8 2 47 701611C Lockwasher, M8 2 48 --------- Capscrew, M12 x 1.75 x 45 4 49 701613C Lockwasher, M12 28 50 00772648 Nut, M12 x 1.75 Gr 8.8 4 51 00766177 Capscrew, M12 x 1.75 x 45 Gr 8.8 8 52 00754565 Socket Head Capscrew, M12 x 1.75 x 35 20 53 00762462 Capscrew, M12 x 1.75 x 25 Gr 8.8 12 17-1-3
AXLE ASSEMBLY 2 MODELS HT417/HT417H (SPRING & HYDRAULIC LIFT) HYDRAULIC LIFT VERSION ONLY * * * * * * * * * * * * * * * * * * * * * * SPRING LIFT VERSION ONLY * * 17-1-4
AXLE ASSEMBLY 2 MODELS HT417/HT417H (SPRING & HYDRAULIC LIFT) REF. PART NO. NO. DESCRIPTION QTY. 1 3670276 RH Lateral Axle 1 2 3670277 LH Lateral Axle 1 3 3676457 Fork Housing 2 4 --------- Shaft, Gearbox Lateral 2 5 3677552 Inner Tube 2 6 3677424 Spring 2 7 3670278 Outer RH Tube 1 8 3670279 Outer LH Tube 1 9 3670227 Wdmt, Spring Hitch 2 10 3677517 Pin, Bent 2 11 3677423 Spring 2 12 3678702 Guard Flap-Rubber 2 13 3677553 Plate, Guard 2 14 3677554 Plate, Guard 2 15 3677518 Pin 4 16 3677515 Bushing 4 17 3636003 Bearing, Ball Two Rubber Seals 2 18 3678200 Ring, Ext. Retaining Snap E30 8 19 3678402 Screw, Set, M8 x 1.25 x 12 4 20 3676906 Shim 4 21 3676907 Shim 4 22 00754565 Socket Head Capscrew, M12 x 1.75 x 35 14 23 701613C Lockwasher, M12 14 24 61354C8 Capscrew, M8 x 1.25 x 16 Gr 8.8 8 25 701511C Lockwasher, M8 8 26 703415W Roll Pin, 6 MM x 45 MM 6 27 70349 Roll Pin, 6 MM x 26 MM 2 28 001465 Grease Fitting, Straight, M6 4 29 3678205 Ring, Ext. Retaining Snap E29 4 30 3670280 RH Lateral Axle 1 31 3670281 LH Lateral Axle 1 17-1-5
DRAWBAR ASSEMBLY MODEL HT417H (HYDRAULIC LIFT) 17-1-6
DRAWBAR ASSEMBLY MODEL HT417H (HYDRAULIC LIFT) REF. PART NO. NO. DESCRIPTION QTY. 1 3670272 Drawbar 1 2 3670208 Wdmt, Center Guard 1 3 3670219 Wdmt, RH Lateral Guard 1 4 3670220 Wdmt, LH Lateral Guard 1 5 3670207 Wdmt, Stand 1 6 3670211 Pin 1 7 3677548 Pin, Drawbar 1 8 3670204 Wdmt, Handle 1 9 3677549 Pin 1 10 3677507 Screw, Tie Rod 1 11 3670271 Fork 1 12 3677550 Pin 1 13 3676776 Plug, Plastic 1 14 3638400 Hairpin, Cotter, M3 1 15 3676775 Plug,Plastic 6 16 703315W Roll Pin 5 17 70349 Roll Pin, 6 MM x 26 MM 1 18 001465 Grease Fitting, Straight, M6 3 19 3676907 Shim 2 20 70209C A12 External Serrated Washer 8 21 00762395 Capscrew M12 x 1.75 x 20 Gr 8.8 4 22 00762462 Capscrew M12 x 1.75 x 25 Gr 8.8 6 23 3678600 Rope 1 24 3677125 RH Cylinder 1 25 3677126 LH Cylinder 1 26 3670215 Wdmt, RH Coupler Latch 1 27 3670216 Wdmt, LH Coupler Latch 1 28 3677420 Spring, RH 1 29 3677421 Spring, LH 1 30 3670273 Hitch 2 31 3670274 Support 1 32 701613C Lockwasher, M12 2 33 3677511 Pin 2 34 3677551 Pin 2 35 703413W Roll Pin, M6 x 36 10 36 703411 Roll Pin, M6 x 30 2 37 701513C Flatwasher, M12 6 38 00754565 Socket Head Capscrew M12 x 1.75 x 35 4 39 --------- Nut M12 x 1.75 Gr. 8.8 4 40 00762399 Capscrew M6 x 1 x 16 2 41 70092C Locknut, Toplock, M6 x 1 2 17-1-7
DRIVELINE ASSEMBLY MODELS HT417/HT417H (SPRING & HYDRAULIC LIFT) 17-1-8
DRIVELINE ASSEMBLY MODELS HT417/HT417H (SPRING & HYDRAULIC LIFT) REF. PART NO. NO. DESCRIPTION QTY. 3676461 Driveline Assembly 1 1 3616514 Yoke 1 2 3616429 Cross Journal Assembly 2 3 3616430 Outer Yoke Tube 1 4 703518W Flexible Pin 1 5 3616415 Cardan Tube 1 6 3616400 Cardan Tube 1 7 703517W Flexible Pin 1 8 3616432 Inner Tube Yoke 1 9 3616516 Torque Limiter LW3 S60 x 04 1 10 ------ Cone Shield Bell 03-04 2 11 ------ Outer Bearing 03-04 1 12 ------ Outer Base Cone 03-04 1 13 ------ Screw 6 14 ------ Outer Safety Tube 1 15 ------ Inner Safety Tube 1 16 ------ Cone, Inner Base 03-04 1 17 ------ Inner Bearing 03-04 1 18 ------ Chain 1 19 00756005 Label Danger Outer Drive Tube 1 20 00756004 External Shield Label 1 21 3616512 Ball Collar Kit 2 22 1416449 Grease Nipple 1 23 3616417 Casing w/yoke 1 24 2516548 Ratchet Tooth 24 25 3616517 Hub 1 26 2516550 Retaining Washer 1 27 2516551 Circlip 1 28 --------- Outer Half Shaft 1 29 --------- Inner Half Shaft 1 30 3616518 Safety Guard 1 17-1-9
GEARBOX ASSEMBLY MODELS HT417/HT417H (SPRING & HYDRAULIC LIFT) REF. PART NO. NO. DESCRIPTION QTY. 1 3676458 Gearbox, Outer Housing 2 2 3676411 Shaft, Rotor 2 3 3676419 Gear, Pinion 2 4 3676456 Crown Gearbox 2 5 3676454 Tine Disc 2 6 3676455 Hub 2 7 3636003 Bearing, Ball Two Rubbe Seals 2 8 710630 Flat Key, Rnd End, 8 x 7 x 30mm 2 9 703616W Roll Pin, M10 x 55 2 10 703417W Roll Pin, M6 x 55 2 11 00754459 Bearing, 35 x 72 x 17 4 12 701613C Lockwasher, M12 8 13 00754565 Socket Head Capscrew, M12 x 1.75 x 35 8 14 61377C8 Capscrew, M12 x 1.75 x 30 Gr. 8.8 12 15 00766457 Grease Fitting M10 x 1.5 Str PG 2 17-1-10
DRAWBAR ASSEMBLY MODEL HT417 (SPRING LIFT) REF. PART NO. NO. DESCRIPTION QTY. 1 3670270 Drawbar 1 2 3670208 Wdmt, Center Guard 1 3 3670210 Wdmt, RH Lateral Guard 1 4 3670209 Wdmt, LH Lateral Guard 1 5 3670207 Wdmt, Stand 1 6 3670211 Wdmt, Pin 1 7 3677548 Pin, Drawbar 1 8 3670204 Handle 1 9 3677549 Pin 1 10 3677507 Tie Rod 1 11 3670271 Fork 1 12 3677550 Pin 1 13 3676776 Plug, Plastic 1 14 3638400 Hairpin, Cotter, M3 1 15 3676775 Plug, Plastic 6 16 703315W Roll Pin 5 17 70349 Roll Pin, 6 MM x 26 MM 1 18 001465 Grease Fitting, Straight, M6 3 19 3676907 Shim 2 20 70209C A12 External Serrated Washer 8 21 00762395 Capscrew M12 x 1.75 x 20 Gr 8.8 4 22 00762462 Capscrew M12 x 1.75 x 25 Gr 8.8 4 17-1-11
HYDRAULIC CYLINDER & HOSE ASSEMBLY MODEL HT417H (HYDRAULIC LIFT) 17-1-12
HYDRAULIC CYLINDER & HOSE ASSEMBLY MODEL HT417H (HYDRAULIC LIFT) REF. PART NO. NO. DESCRIPTION QTY. 1 --------- Cylinder Tube, RH 1 2 --------- Cylinder Tube, LH 1 3 --------- Rod, Cylinder 2 4 --------- Spring, Cylinder 2 5 3687104 Head, Cylinder 2 6 --------- Piston, Cylinder 2 7 --------- Gasket 2 8 --------- Gasket 2 9 --------- Gasket 2 10 --------- Gasket 2 11 --------- Gasket 2 12 3677105 Kit, Seal 2 13 --------- Roll Pin, 3.5 MM x 18 MM 2 14 3677125 RH Cylinder, Complete 1 15 3677126 LH Cylinder, Complete 1 16 3677102 Bolt, Hydraulic 2 17 3678400 Washer, Copper 4 18 3677206 Hose (1/4 ) 2 19 3677103 Tee, Hydraulic Union 1 20 3677104 Fitting, Hyd. Nipple Adapter 1 21 3677207 Hose (3/8 ) 1 22 3638408 Copper Washer, 1/2 ID 1 23 3637102 Male Coupling Tip 1 24 3668424 Collar, Hose 6 25 --------- Socket Head Capscrew, Metric 6 17-1-13
TIRE ASSEMBLY MODELS HT417/HT417H (SPRING & HYDRAULIC LIFT) 17-1-14
TIRE ASSEMBLY MODELS HT417/HT417H (SPRING & HYDRAULIC LIFT) REF. PART NO. NO. DESCRIPTION QTY. 1 3670231 Wdmt, RH Support Spindle 1 2 3670230 Wdmt, LH Support Spindle 1 3 3670226 Wdmt, LH Center Support Spindle 1 4 3670225 Wdmt, RH Center Support Spindle 1 5 3677555 Spacer 4 6 3676908 Shim 4 7 3676909 Shim 4 8 3676905 Shim 4 9 3676903 Gasket 47, 63 x 3, 53 4 10 3677556 Arm, Tine 24 11 3677422 Tine, Spring 24 12 00766177 Capscrew M12 x 1.75 x 45 Gr 8.8 24 13 3677512 Plate, Tine 24 14 00772648 Locknut, Toplock M12 X 1.75 Gr. 10.9 48 15 00754529 Capscrew, M12 x 1.75 x 30 Gr. 8.8 24 16 00754565 Socket Head Capscrew, M12 x 1.75 x 35 24 17 703616W Roll Pin, M10 x 55 4 18 703417W Roll Pin, M6 x 55 4 19 701613C Lockwasher, M12 24 20 3678414 Washer 24 21 3676700 Cover, Inside Dust 4 22 3676002 Bearing, Ball 6205 2RS 8 23 3677514 Spacer 4 24 3677600 Rim, 16 x 6.50-8 4 25 3677800 Tube 16 x 6.50 4 26 3677801 Tire 16 x 6.50-8 6 Ply 4 27 3676701 Cover, Outer Dust 4 28 701515C Flatwasher, M16 4 29 3038445 Locknut, Toplock M16 x 2.0 4 30 3670100 Tire Assy (16 x 6.50-8, 6 Ply) 4 17-1-15
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL APRIL, 2011 DECALS - BUSH HOG MARKING MODELS HT417/HT417H 1 4 2 5 3 6 7 9 10 8 11 12 13 14 15 16 17 REF. PART NO. NO. DESCRIPTION QTY. 1 50068924 Decal, Model HT417 2 2 00725746 Decal, Peligro 1 3 00786980 Decal, Genuine Bush Hog Parts 1 4 999001 Decal, Warning - Tractor Weight 1 5 50068925 Decal, Model HT417H 2 6 3678303 Decal, Danger - Rotors 1 7 999200 Decal, General Warning - All Unit 1 8 00756004 Decal, Danger - Guard Missing 1 9 00763977 Decal, Important - Notice to Owner 1 10 00776031 Canister, Parts Manual 1 11 03200347 Emblem, SMV 1 12 00777394 Decal, Tow 1 13 02962764 Decal, Pinch Points 1 14 02965262 Decal, Warning-Oil Leak 1 15 50063360 Decal, Bush Hog 8 2 16 2738332 Decal, Red Oblong Reflector 1 17 2738333 Decal, Yellow Oblong Reflector 1 18 00756005 Decal, Rotating Driveline (Not Shown) 1 17-1-16