KINETICS TM Restrained Isolators Model FLSS 1 and 2 Description Kinetics Model FLSS Seismic Control Restrained Vibration Isolators consist of free-standing, large diameter, laterally stable steel springs assembled into welded steel housing assemblies. The housings are fabricated to limit vertical movement of the isolated equipment if equipment loads are reduced or if the equipment is subjected to large external forces such as high winds or seismic events. The housings also provide a constant free and operating height to facilitate installation. elements are complete with internal noise isolation pads and leveling bolts as a part of the top load plate assembly. Holes are provided in all isolators for bolting to the structure and the supported equipment. To assure stability, the springs have a lateral spring stiffness greater than 1.2 times the rated vertical stiffness and are designed to provide a minimum overload capacity of 50%. Model FLSS isolators are available with deflections to 2" (50 ) and with load capacities to 18,000 lbs. (8165 kg) as standard products. Custom isolators with higher deflection and greater load capabilities are also available. Kinetics Model FLSS Isolators are recoended for the isolation of vibration produced by equipment carrying a large fluid load which may be drained, such as boilers and chillers, and for the isolation of cooling towers, aircooled condensers, etc., where motion due to wind loads must be minimized. Application Kinetics Model FLSS Seismic Control Restraint Isolators are recoended as a noise and vibration isolator for mechanical equipment under the following conditions: 1. When the mechanical equipment is located above or near noise and vibration sensitive areas. 2. When the mechanical equipment is subjected to seismic events, high wind loads or other external forces. 3. When the equipment to be isolated has significant changes of weight due to fluid drainage during maintenance operations such as boilers, chillers and cooling towers. Operating static deflections are available up to 2" (50 ) to maintain a high degree of noise and vibration control while compensating for long span flexible floor structures.
Specifications Vibration isolators shall be seismically rated, restrained spring isolators for equipment which is subject to load variations and large external forces. Isolators shall consist of large diameter, laterally stable, steel springs assembled into welded steel housing assemblies designed to limit movement of the supported equipment in all directions. Housing assembly shall be of fabricated steel members and shall consist of a top load plate complete with adjusting and leveling bolts, adjustable vertical restraints, isolation washers, and a bottom plate with internal non-skid noise isolation pads and holes for anchoring of housing to supporting structure. Housing shall be hotdip galvanized for corrosion resistance. Housing shall be designed to provide a constant free and operating height within 1/8" (3 ). The isolator housing shall provide a minimum of 1 g restraint in all directions. elements shall be selected to provide static deflections as shown on the vibration isolation schedule or as indicated or required in the project documents. s shall be color coded or otherwise identified. elements shall have a lateral stiffness greater than 1.2 times the rated vertical stiffness and shall be designed to provide a minimum of 50% overload capacity. Non-welded spring elements shall be polyester powder coated, and shall have a 1000 hr rating when tested in accordance with ASTM B-1. Vibration isolators shall be Model FLSS as manufactured by Kinetics Noise Control, Inc.
Isolator Type FLSS-1-0 FLSS-1-450 FLSS-1-6 FLSS-1-800 FLSS-1-1000 FLSS-1-10 FLSS-1-00 FLSS-1-2200 FLSS-1-2465 FLSS-1- FLSS-1-3500 FLSS-1-00 FLSS-1-3 FLSS-1-4 FLSS-1-4930 FLSS-1-5730 FLSS-1-7000 FLSS-1-5000 FLSS-1-6800 FLSS-1-8800 FLSS-1-90 FLSS-1-160 FLSS-1-000 FLSS-2-100 FLSS-2-135 FLSS-2-185 FLSS-2-2 FLSS-2-0 FLSS-2-375 FLSS-2-500 FLSS-2-6 FLSS-2-750 FLSS-2-875 FLSS-2-995 FLSS-2-1120 FLSS-2-00 FLSS-2-1600 FLSS-2-1975 FLSS-2-2000 FLSS-2-00 FLSS-2-2750 FLSS-2-30 FLSS-2-30 FLSS-2-3500 FLSS-2-3900 FLSS-2-4100 FLSS-2-4500 FLSS-2-0 FLSS-2-5000 FLSS-2-5500 FLSS-2-6050 FLSS-2-6500 FLSS-2-7000 FLSS-2-7800 FLSS-2-8200 FLSS-2-9000 FLSS-2-8000 FLSS-2-10000 FLSS-2-11000 FLSS-2-100 FLSS-2-13000 FLSS-2-000 FLSS-2-15600 FLSS-2-16 FLSS-2-18000 Color Green Black Gray Red Org/Gray Blu/Gray /Brn Org/Gray Blu/Gray Blu/Brn Org/Gray Blu/Gray Blu/Brn Gray Beige Gray/Brn /Brn Green Grn/Brn Black Blk/Brn Org/Brn Org/Grn Red Red/Grn Blu/Blu Blu/Grn Blu/Blk Blu/Org Blu/Org/Grn Blu/Red Blu/Red/Grn Blu Blu/Blu Blu/Grn Blu/Blk Blu/Org Blu/Org/Grn Blu/Red Blu/Red/Grn Blu/Blu Blu/Grn Blu/Blk Blu/Org Blu/Org/Grn Blu/Red Blu/Red/Grn lbs. 0 450 6 800 1000 10 00 2200 2465 3500 00 3 4 4930 5730 7000 5000 6800 8800 90 160 000 100 135 185 2 0 375 500 6 750 875 995 1120 00 1600 1975 2000 00 2750 30 30 3500 3900 4100 4500 0 5000 5500 6050 6500 7000 7800 8200 9000 8000 10000 11000 100 13000 000 15600 16 18000 kg 113 204 283 363 454 567 771 998 1118 1300 1588 1134 1542 1996 2236 99 35 0 3085 3992 4472 98 6350 45 61 84 113 0 283 340 397 4 208 635 726 896 907 1134 1247 1372 74 1588 69 10 2041 18 2268 2495 2744 2948 35 3538 3719 4082 3629 4536 4990 5488 5897 6350 70 7439 8165 Capacity 1.79 1.54 1.44 1.31 1.15 1.09 0.95 1.09 0.95 1.09 0.95 2.01 1.98 2.02 2.02 2.02 45 39 37 33 29 28 24 26 28 24 26 28 24 26 50 Deflection O.D. 15. 15. 15. 15. 15. 15..50.50.50.50.50.50.50.50.50.50.50.50.50.50.50.50.50.50 L W D d 5 5 5 5 5 5 7 7 7 7 7 7 7 7 7 H
KINETICS TM Seismic Restraint for Isolated and Suspended Mechanical Equipment for - Piping Fans VAV & Fan Terminal Boxes Silencers & Mufflers Ductwork Air Handlers Kinetics KSCA Cable Attachment Bracket KINETICS KSCA KINETICS TM Floor-Mounted Seismic Restraints Seismic Control Isolators Model FHS Combination spring isolator & seismic restraint All-directional restraint with vertical limit stops Seismic Snubber Model HS-5 Double axis horizontal and vertical seismic restraint Standard capacities to 3,275 lbs. Can be bolted or welded in place Kinetics KSUA Cable Attachment Bracket Kinetics KSUA Cable Attachment Bracket Modular Restraint/Isolator Model FMS Can be used as a restraint device or as a seismically rated vibration isolator assembly Restraint compents are available in 8 sizes with horizontal force ratings to 70,000 lbs. Standard isolation elements are available to 4 deflection with support capacities to 23,000 lbs. Ideal for equipment mounted on structural frame or concrete inertia bases Kinetics FMS with isolator Kinetics FMS without isolator United States 6300 Irelan Place P.O. Box 655 Dublin, Ohio 430 Phone: 6-889-0480 Fax: 6-889-0540 www.kineticsnoise.com sales@kineticsnoise.com Canada 3570 Nashua Drive Mississauga, Ontario L4V 1L2 Phone: 905-670-4922 Fax: 905-670-1698 Kinetics Noise Control, Inc. is continually upgrading the quality of our products. We reserve the right to make changes to this and all products without notice. FLSS 1/10
KINETICS TM Restrained Isolators Model FLSS 4 Description Kinetics Model FLSS Seismic Control Restrained Vibration Isolators consist of free-standing, large diameter, laterally stable steel springs assembled into welded steel housing assemblies. The housings are fabricated to limit vertical movement of the isolated equipment if equipment loads are reduced or if the equipment is subjected to large external forces such as high winds or seismic events. The housings also provide a constant free and operating height to facilitate installation. elements are complete with internal noise isolation pads and leveling bolts as a part of the top load plate assembly. Holes are provided in all isolators for bolting to the structure and the supported equipment. To assure stability, the springs have a lateral spring stiffness greater than 1.2 times the rated vertical stiffness and are designed to provide a minimum overload capacity of 50%. FLSS isolators are available with deflections to 4 (100 ) and with load capacities to 23,200 lbs. (10523 kg) as standard products. Custom isolators with higher deflection and greater load capabilities are also available. Kinetics Model FLSS Isolators are recoended for the isolation of vibration produced by equipment carrying a large fluid load which may be drained, such as boilers and chillers, and for the isolation of cooling towers, air-cooled condensers, etc., where motion due to wind loads must be minimized. Application Kinetics Model FLSS Seismic Control Restraint Isolators are recoended as a noise and vibration isolator for mechanical equipment under the following conditions: 1. When the mechanical equipment is located above or near noise and vibration sensitive areas. 2. When the mechanical equipment is subjected to seismic events, high wind loads or other external forces. 3. When the equipment to be isolated has significant changes of weight due to fluid drainage during maintenance operations such as boilers, chillers and cooling towers. Operating static deflections are available up to 4 (100 ) to maintain a high degree of noise and vibration control while compensating for long span flexible floor structures. Specification Vibration isolators shall be seismically rated, restrained spring isolators for equipment which is subject to load variations and large external forces. Isolators shall consist of large diameter, laterally stable, steel springs assembled into welded steel housing assemblies designed to limit movement of the supported equipment in all directions. Housing assembly shall be of fabricated steel members and shall consist of a top load plate complete with adjusting and leveling bolts, adjustable vertical restraints, isolation washers, and a bottom plate with internal non-skid noise isolation pads and holes for anchoring of housing to supporting structure. Housing shall be hot-dip galvanized for corrosion resistance. Housing shall be designed to provide a constant free and operating height within 1/8 (3 ). The isolator housing shall provide seismic and wind restraint required by current building codes. elements shall be selected to provide static deflections as shown on the vibration isolation schedule or as indicated or required in the project documents. s shall be color coded or otherwise identified. elements shall have a lateral stiffness greater than 1.2 times the rated vertical stiffness and shall be designed to provide a minimum of 50% overload capacity. Non-welded spring elements shall be polyester powder coated, and shall have a 1000 hr rating when tested in accordance with ASTM B-1. Vibration isolators shall be Model FLSS as manufactured by Kinetics Noise Control, Inc.
FLSS-4 6/12 United States 6300 Irelan Place P.O. Box 655 Dublin, Ohio 430 Phone: 6-889-0480 Fax: 6-889-0540 Canada 3570 Nashua Drive Mississauga, Ontario L4V 1L2 Phone: 905-670-4922 Fax: 905-670-1698 www.kineticsnoise.com sales@kineticsnoise.com Kinetics Noise Control, Inc. is continually upgrading the quality of our products. We reserve the right to make changes to this and all products without notice. Isolator Type FLSS-4-100 FLSS-4-0 FLSS-4-500 FLSS-4-750 FLSS-4-1000 FLSS-4-10 FLSS-4-1600 FLSS-4-20 FLSS-4-00 FLSS-4-2750 FLSS-4-3000 FLSS-4-30 FLSS-4-3500 FLSS-4-3850 FLSS-4-4200 FLSS-4-4450 FLSS-4-4700 FLSS-4-4950 FLSS-4-5200 FLSS-4-5450 FLSS-4-5800 FLSS-4-5500 FLSS-4-6000 FLSS-4-6500 FLSS-4-7000 FLSS-4-7700 FLSS-4-8 FLSS-4-8900 FLSS-4-9 FLSS-4-9900 FLSS-4-10 FLSS-4-10900 FLSS-4-11600 FLSS-4-11000 FLSS-4-12000 FLSS-4-13000 FLSS-4-000 FLSS-4-15 FLSS-4-16800 FLSS-4-800 FLSS-4-18800 FLSS-4-19800 FLSS-4-20800 FLSS-4-800 FLSS-4-23200 Color Gray Grn Black Red Beige Bge/Blu Bge/Grn Bge/Blk Bge/Red Bge/Brn Bge/Org Chrome Chr/Blu Chr/Grn Chr/Blk Chr/Red Chr/Brn Chr/Org Bge/Grn Bge/Blk Bge/Red Bge/Brn Bge/Org Chrome Chr/Blu Chr/Grn Chr/Blk Chr/Red Chr/Brn Chr/Org Bge/Grn Bge/Blk Bge/Red Bge/Brn Bge/Org Chrome Chr/Blu Chr/Grn Chr/Blk Chr/Red Chr/Brn Chr/Org lbs. 100 0 500 750 1000 10 1600 20 00 2750 3000 30 3500 3850 4200 4450 4700 4950 5200 5450 5800 5500 6000 6500 7000 7700 8 8900 9 9900 10 10900 11600 11000 12000 13000 000 15 16800 800 18800 19800 20800 800 23200 kg 45 113 340 454 567 726 1 1134 1247 1361 74 1588 46 1905 2018 32 2245 2359 2472 2631 2495 2722 2948 35 3493 0 4037 4264 4491 47 4944 5262 4990 5443 5897 6350 6985 20 8074 8528 8981 9435 9888 10523 Capacity Deflection 3 3 3 3 3 3 3 O.D. 2 2 2 2 2 2 2 2 2 2 2 2 6 6 6 6 6 6 6 6 6 6 6 6 L.00.00.00.00.00.00.00.00.00.00.00.00 W D d.00.00.00.00.00.00.00...................................... H