Series 462 ARCHITECTURAL SERIES Photo courtesy of AVS Windows & Doors DATE: MAY 2013 REPLACES: MARCH 2008
ARCHITECTURAL SERIES Series 462 KEY FEATURES/PERFORMANCE CHARACTERISTICS Scale: not to scale 102mm thick commercial grade sliding window, incorporates bold frame lines and thick (strong) sashes that can carry thick heavy glass, including double glazing. The perimeter frame designed to make installation into brick veneer and cavity brick easier with built-in nailing fins (weather bars). Extra strong sashes allow large sash windows to be fabricated for high wind load areas. Double sash design with the external sash fixed. Both fixed and opening sashes can be installed, replaced or reglazed from inside. Large variety of window combinations possible (SF, FS, SFS, SS or FSSF) with and without highlights and/or lowlights. We also offer double sliding configuration where both sashes can be opened. Sliders can be fitted with standard mortice locks as shown below or alternative surface locks. Sashes run on heavy duty wheel carriages. Flyscreens can be fitted. When there is no requirement for flyscreens, frame is fitted with cavity closers so there are no unwanted recesses. Co-extruded PVC sill seal keeps water out of the system. Built-in proprietary ball valve drainage to transfer any water that may get into the drainage trough to the tubular sump sill. Will resist up to 300Pa water infiltration and comply with airconditioning requirements. Series 462. Internal View. Maximum Panel Height* Maximum Panel Width* Maximum Glass Thickness 1600mm 1350mm 20mm * Subject to individual site conditions and wind loads. Contact AWS Technical Support for more information, email techsupport@awsaustralia.com.au 2D & 3D CAD Files Available To access 2D & 3D CAD models visit our online specifier resource centre www.specifyaws.com.au MORE INFORMATION For the latest updates regarding this product visit our website www.elevatealuminium.com.au/462 This image shows the ICON sliding window mortice lock.
Series 462 architectural sliding window Sound Reduction A number of glass combinations have been tested with this system to acheive sound reduction numbers listed below. Glass Description 4mm Glass 6.38mm Laminated glass 10.38mm Laminated glass 16mm IGU (4mm Glass / 8mm air gap / 4mm Glass NOTE: The actual tests were carried out on a product very similar to this window (Series 601). Rating Rw31 Rw33 Rw35 Rw32 Scale: not to scale HOW TO SPECIFY SYSTEM NAME Elevate Aluminium Systems Series 462 FINISH Powder Coat Anodised ARCHITECTURAL SERIES WERS RATINGS Single Glazed Window ID Glass Type Uw SHGCw Tvw Inf AWS-030-01 5CLR 6.0 0.66 0.69 1.15 AWS-030-02 5SG 6.0 0.46 0.57 1.15 AWS-030-03 5GY 6.0 0.49 0.39 1.15 AWS-030-04 6.38Sct 4.2 0.54 0.63 1.15 AWS-030-05 6.38VLam 5.9 0.65 0.69 1.15 AWS-030-06 4SnClr 4.8 0.46 0.51 1.15 AWS-030-07 6SnClr 4.8 0.45 0.50 1.15 AWS-030-08 6EVanBG 4.6 0.35 0.42 1.15 AWS-030-09 6EVanClr 4.6 0.48 0.49 1.15 COLOUR Select from the AWS range of approved powder coat or anodising colours GLASS Specify thickness 20mm Specify thermal performance where applicable (Uv & SHGC) Specify acoustic performance where applicable (RW) Specification Assistance AWS-030-10 6EVanGy 4.6 0.31 0.24 1.15 AWS-030-11 6EVanSpB 4.6 0.28 0.29 1.15 AWS-030-12 6EVanSpGn 4.6 0.28 0.35 1.15 AWS-030-13 6.38LamGy 6.0 0.27 0.10 1.15 AWS-030-14 6.38TLam 6.0 0.31 0.25 1.15 AWS-030-15 6.38SnClr 4.7 0.44 0.50 1.15 AWS-030-16 6.38SnGy 4.7 0.33 0.24 1.15 AWS-030-17 6.38CPClr 4.4 0.52 0.61 1.15 AWS-030-18 6.38CPGn 4.4 0.38 0.53 1.15 AWS-030-19 6.38CPGy 4.4 0.38 0.29 1.15 AWS-030-20 10.38GyLam 6.0 0.18 0.07 1.15 AWS-030-21 10.38ClrLam 6.0 0.41 0.41 1.15 AWS-030-22 10.38SnClr 5.1 0.36 0.40 1.15 AWS-030-23 10SnClr 4.8 0.33 0.36 1.15 AWS-030-24 10.38TLam 4.8 0.33 0.36 1.15 Need help specifying this product? Email techsupport@ awsaustralia.com.au and our qualified technical advisors will assist you with product selection and specification for your project. NOTES 1. Uw is the whole window U-value 2. SHGCw is the whole window solar heat gain coefficient 3. Tvw is the whole window visible (light) transmittance 4. Maximum air infiltration is 5.0L/s.m2 at a positive pressure difference of 75 Pa as measured according to AS 2047 5. Static performance (Uw SHGCw Tvw Tdw) calculated using Window 6.3 and Therm 6.3 software (LBNL), 1999-2010 6. Results disclosed at Australian Fenestration Rating Council (AFRC) regulations. 7. Ratings for use with Section J of the Building Code of Australia - Class 2-9 For the latest WERS data for this system visit www.wers.net PAGE 2.205
ARCHITECTURAL SERIES Series 462 WERS RATINGS Double Glazed Window ID Glass Type Uw SHGCw Tvw Inf AWS-030-25 4/10/4 4.0 0.56 0.58 1.15 AWS-030-26 5/8/5 4.1 0.54 0.58 1.15 AWS-030-27 4/10/4ET 3.5 0.52 0.54 1.15 AWS-030-28 4/10Ar/4ET 3.3 0.52 0.54 1.15 scale: not to scale NOTES 1. Uw is the whole window U-value 2. SHGCw is the whole window solar heat gain coefficient 3. Tvw is the whole window visible (light) transmittance 4. Maximum air infiltration is 5.0L/s.m2 at a positive pressure difference of 75 Pa as measured according to AS 2047 5. Static performance (Uw SHGCw Tvw Tdw) calculated using Window 6.3 and Therm 6.3 software (LBNL), 1999-2010 6. Results disclosed at Australian Fenestration Rating Council (AFRC) regulations. 7. Ratings for use with Section J of the Building Code of Australia - Class 2-9 For the latest WERS data for this system visit www.wers.net AWS-030-29 4Az/10/4ET 3.5 0.31 0.45 1.15 AWS-030-30 5SG/8Ar/5ET 3.4 0.32 0.44 1.15 AWS-030-31 4SnClr/10/4 4.3 0.34 0.37 1.15 AWS-030-32 4SnClr/10Ar/4 4.1 0.34 0.37 1.15 AWS-030-33 6.38CPClr/8/4 4.3 0.39 0.44 1.15 AWS-030-34 6.38CPClr/8Ar/4 4.0 0.39 0.44 1.15 AWS-030-35 6.38CPGy/8/4 4.3 0.28 0.21 1.15 AWS-030-36 6.38CPGy/8Ar/4 4.1 0.28 0.21 1.15 AWS-030-37 6SnClr/10/6 4.3 0.33 0.36 1.15 AWS-030-38 6SnClr/10Ar/6 4.1 0.33 0.36 1.15 AWS-030-39 10SnClr/6/6 4.5 0.32 0.35 1.15 AWS-030-40 10SnClr/6Ar/6 4.3 0.32 0.35 1.15
Series 462 architectural sliding window Design Features The 26mm thick heavy duty sliding window sashes have been fitted into custom head, sill and jamb inlay adaptor that snaps to standard 30mm frame as shown right or alternative 44mm wide jamb. The extra strong sashes allow large sash windows to be fabricated for high wind load areas. Double sash design with the external sash fixed (SF) or both sashes moving (SS). Both fixed and opening sashes can be installed, replaced and/or reglazed from inside the building. This could be an important feature in elevated situations There is a large variety of window combinations possible (SF, FS, SFS, FSSF or SS) with and without highlights/lowlights. We have designed a number of compatible framing suites that can be coupled or used together. Series 400 CentreGLAZE framing Series 424 Double GLAZED CentreGLAZE framing 102mm x 44mm head and sill, 102mm x 30mm (or alternative 44mm) jamb, 44mm mullion and 44mm transoms match. Sliders can be fitted with standard mortice locks or alternative surface locks. Sashes run on heavy duty wheel carriages. Two flyscreen options (not applicable to type 'SS' windows): No flyscreens: Frame fitted with cavity closers so there are no unwanted recesses to catch dust, water and bugs, as shown right. Conventional flyscreens: Two conventional size extruded flyscreen frames (25 x 11) can be fitted into the window using custom frame trims to accept the screen, refer details in these notes. Scale: not to scale ARCHITECTURAL SERIES Co-extruded PVC sill seal keeps water out of the system. We have built-in the proprietary ball valve drainage to transfer any water that may get into the drainage trough to the tubular sump sill. This valve also reduces blowback through the hooded external drainage holes. Unwanted frame recesses are fitted with snap-in flat closers to ensure that the clean looks are maintained. It's possible to re-hand the window on-site (change type 'SF' to 'FS') depending on what lock has been used. Sashes and sidelights will accept a variety of glass thicknesses from 4mm to 20mm insulating glass units. Dedicated sash rail and stiles for 16mm IGUs. We have 90 and 135 corner mullions for bay and box windows. PAGE 2.207
ARCHITECTURAL SERIES Series 462 TYPICAL CONFIGURATIONS Scale: not to scale Series 462 can be fabricated as 'SF', 'FS', 'SFS', 'FSSF' or SS with lowlights and/or highlights as shown above. The illustration left shows how the unwanted recesses are closed off to improve weather performance and appearance. Alternative 44mm wide jamb illustrated. Water Resistance: We always recommend the use of sub-sills under commercial frames. Safety Glass: On the example below, the door panel and the two sashes in the sliding window sidelights would require grade 'A' safety glass. If the opening sash was in the open position it would be within 300mm of the door opening. Highlight and lowligh must also be glazed using grade 'A' safety glass. Refer Australian Standard AS 1288 for more information.
Series 462 architectural sliding window sash strength 'SF', 'FS' and 'SS' windows Height Width Meeting stile combinations mm mm Light Medium Heavy Extra Heavy L/180 S 1064 1717 2528 1600 1832 L/250 S 766 1243 2216 U 2273 2576 3792 L/180 S 946 1517 2234 1600 2132 L/250 S 681 1105 1970 U 2008 2276 3351 L/180 S 871 1388 2043 1600 2432 L/250 S 627 1017 1814 U 1837 2082 3065 L/180 S 826 1309 1927 1600 2732 L/250 S 595 965 1720 U 1732 1963 2890 Scale: not to scale Rating tables for window meeting stiles on this page. S = Serviceability limit state (deflection = L/180 or deflection L/250). U = Ultimate strength limit state (factored yield strength = 104MPa). These tables have been calculated using nominal section properties. A typical assembly has been tested as per the requirements of AS 2047. Serviceability rating has been limited to 3333Pa and Ultimate strength rating has been limited to 5000Pa. ARCHITECTURAL SERIES SFS windows Height Width Meeting stile combinations mm mm Light Medium Heavy Extra Heavy L/180 S 1100 1762 2594 1600 2432 L/250 S 792 1284 2289 U 2332 2643 3891 L/180 S 1028 1641 2416 1600 2732 L/250 S 740 1200 2140 U 2172 2462 3624 L/180 S 981 1565 2304 1600 3032 L/250 S 707 1146 2043 U 2071 2347 3456 L/180 S 947 1510 2223 1600 3332 L/250 S 682 1106 1972 U 1998 2265 3334 L/180 S 918 1461 2151 1600 3632 L/250 S 661 1072 1911 U 1935 2192 3227 FSSF windows Height Width Meeting stile combinations mm mm Light Medium Heavy L/180 S 1507 2444 3333 1600 2432 L/250 S 1085 1760 3138 U 3251 3684 5000 L/180 S 1343 2179 3215 1600 2732 L/250 S 967 1569 2797 U 2891 3276 4823 L/180 S 1219 1976 2908 1600 3032 L/250 S 877 1423 2537 U 2615 2963 4363 L/180 S 1121 1813 2669 1600 3332 L/250 S 807 1309 2334 U 2399 2719 4003 L/180 S 1044 1682 2478 1600 3632 L/250 S 752 1219 2174 U 2228 2524 3716 Wind Ratings (Pa) Extra Heavy 1/4 1/2 1/4 Type 'FSSF' windows are limited by the strength of the centre meeting stiles. Meeting stile combinations External Internal Light 42036 42036 Medium 42036 42014 Heavy 42036 42015 Extra heavy 42015 42015 Details on meeting stiles are shown on later page. Water resistance - 300Pa We always recommend sub-sills under commercial windows. PAGE 2.209
ARCHITECTURAL SERIES Series 462 HEAD AND SILL - 'SF' WINDOW Head We have a dedicated head section to allow the installation of sliding window sashes into framing. Built-in nailing fin on head, jambs and sub-sill make this window significantly more water proof and easier to install into brick veneer and cavity brick walls. Scale: FULL SIZE Weatherpile seals. Recess closed off. If there are no flyscreens, we fit the flat filler as shown on this detail. If there are flyscreens, we use a custom filler to suit the flyscreens, refer flyscreening page later in these notes. For the best flyscreening finish always specify AWS flyscreens and from an approved fabricator. CAD file: DWG 462.SLW.1 Sill We have a dedicated sill section to allow the installation of sliding window sashes into framing. Removable running rail. Proprietary ball drainage valve. We always recommend sub-sills under commercial windows.
Series 462 architectural sliding window JAMB DETAIL Scale: FULL SIZE ARCHITECTURAL SERIES Standard 30mm jamb The custom jamb adaptor has been designed to allow us to have two lines of reveal fixings (as shown). This pulls the reveal up tight on the window frame - no more gaps. The detail left shows the standard 30mm narrow jamb. We also have a 44mm wide nailing fin jamb. Window can be fitted with standard mortice lock (ANDO or ICON ) as shown or alternative surface mounted lock. You can view the lock options in colour on our website www.elevatealuminium.com.au CAD file: DWG 462.SLW.1 This image shows ICON mortice lock and the alternative ANDO cover plate. ICON cover plate is brushed stainless steel. ANDO cover plate is cast aluminium and available in a variety of standard and special powder coat finishes. PAGE 2.211
ARCHITECTURAL SERIES Series 462 HORIZONTAL SECTION THROUGH 'SF' WINDOW Standard 30mm jamb Stainless steel screw assembly. This jamb shows the height adjustable galvanised building-in lug. used on cavity brick installations. External recess in frame can be closed off with optional jamb filler if required. Scale: HALF FULL SIZE Alternative 44mm wide jamb. All unwanted internal and external recesses are closed off with snap-in flat closers. Adhesive buffer at head and sill. Double weatherpile seals at meeting stiles. The standard mullion meeting stile illustrated will cover most situations, but for exposed areas you may have to use the heavier meeting stile on the inside as shown dotted. Wrap around PVC glazing channel wedge. This detail shows standard mortice lock. Available with ANDO or ICON face plate. Weatherpile seals. CAD file: DWG 462.SLW.1 We can fit a snap-in filler to allow us to double fix timber reveal to jamb. This pulls the reveal up tight on the frame. Timber reveals are typically used on brick veneer installations.'
Series 462 architectural sliding window sill DRAINAGE Alternative 44mm wide jamb. Scale: not to scale ARCHITECTURAL SERIES Drain holes Ball valve. Alternative 44mm wide jamb. Flat filler closes over all unwanted recess in perimeter frame inside and out. Sill running rail covers the drainage ball valve and stops short both ends to allow water to escape. If necessary in the future this running rail can be removed/replaced. The legs on running rail give the impression that the sill recess is shallow. PAGE 2.213
ARCHITECTURAL SERIES Series 462 DOUBLE GLAZED WRAP AROUND SLIDING SASH - TYPE 'FS' WITH 16mm IGU AND 24mm IGU IN THE DOUBLE GLAZED FIXED LOWLIGHT Scale: Not to scale This detail is created with run through double glazed jambs. The jamb runs through to ensure overall frame strength and weather resistance. In the lowlight area the wide glazing pocket will accept 24mm IGU's with co-extruded Santoprene captive and roll-in glazing wedges. In sliding sash area we use a dedicated jamb adaptor, to snap into the double glazed frame pocket. Series 462 transom (sill) accept the double glazed CentreGLAZE pocketed filler.to achieve a wide double glazed pocket in the fixed area we snap the double glazed channel adaptor to the transom sill as detailed right. The double glazed unit nests neatly into transom, jambs and sill, giving a clean professional finish. Water resistance 300Pa. Heavy double glazed sashes heavier than 30Kg will be fitted with double bogey wheels.'
Series 462 architectural sliding window DOUBLE GLAZED WRAP AROUND SLIDING SASH WITH 16mm IGU AND 24mm IGU IN THE DOUBLE GLAZED FIXED LOWLIGHT Scale: half full size ARCHITECTURAL SERIES Slider height = S Slider Overlight 16mm double glazed O/A Frame Height = H Lowlight height = L Fixed lowlight 24mm double glazed The detail top left shows 16mm IGU. To get 20mm IGU into the sliding panel we fit an inlay adaptor channel as shown direct left. CAD file: DWG 462.SLW.8 15 10 The double glazed unit nests neatly into transom, jambs and sill, giving a clean professional finish. Sub-sills are standard on Series 462 windows and are fitted with custom moulded nylon end caps. Flexible PVC sill flap caters for sill brick variations. PAGE 2.215
ARCHITECTURAL SERIES Series 462 HORIZONTAL & VERTICAL SECTION TYPE 'SS' WINDOWS VERTICAL SECTION type 'SS' WINDOWS The panels shown on this page will accept glass up to 7.52mm thick, we also have stiles, rails and wedges that will accept 8.38, 10.38 laminated and 16mm IGU's or 20mm thick IGU's with channel adaptor. Scale: half full size HORIZONTAL SECTION type 'SS' WINDOWS Standard 30mm nailing fin jamb. Series 462 windows are fitted with custom ANDO press button locks (both sashes). Key lock when required. CAD file: DWG 462.SLW.1 This cut away image of alternative ICON mortice. The features of this lock are: Stainless steel ICON face plate and push plate. Stainless steel lock tongue hole dress plate. Stainless steel lock tongue. The lock will self latch when closed, can be key locked when required for added security. Panels run on large diameter ball bearing nylon tyres for smooth long term operation. Single wheel rollers used on panels <=30Kg, on heavier panels >30Kg we fit double bogey wheels.
Series 462 architectural sliding window 'SS' TYPE WINDOWS We have successfully tested this window to 300Pa water resistance. Scale: not to scale ARCHITECTURAL SERIES The buffer stop is fitted to the external face on the inner sash top and bottom rail to keep the meeting stile away from the external sash lock. PAGE 2.217
ARCHITECTURAL SERIES Series 462 FLYSCREENING 'SF', 'FS' and 'SFS' scale: HALF FULL SIZE 50 Flyscreen height = S - 112 Elevate flyscreen frame - illustrated alternative Elevate barrier flyscreen frame available. Custom extruded aluminium flyscreen frame designed to match the window system.' PVC flyscreen spline. Flymesh. CAD file: DWG 462.SLW.9 Spacer block ensures that water can escape under the screen and into the drainage system. Water is drained out via the hooded drainage hole/s in the front leg under the screen at meeting stiles. 62 Custom nylon spring clips keep tension on flyscreen - no rattles. 30 58