Product Information Side 03/2015 frame 6 (mm) extrusion 6 (mm) high, 2.6 (mm) above top of roller 3.15 (80mm) extrusion Allows lateral shifting 3.15 (80mm) high, 0.16 (5mm) below top of roller 80 5 Combination of frame heights left/right 6 /6 (mm/mm) 3.15 /6 (80mm/mm) 6 /3.15 (mm/80mm) Width () Module length (L) Zone lengths (ZL) pitch (P) ZL x number of zones 12, 18, 24, 30, 36, 48, 60 + 4.33 2 / 3 (50mm/75mm), 4 (100mm) 3.15 /6 (80mm/mm) 2.6 (mm) with 6 frame s.16 (5mm) higher than frame with 3.15 (80mm) frame Zero pressure accumulation Conveyor from the originator of 24VDC Drive 2015 interroll AG 1
RM 5504 Conveyor Line modules are used for the transportation of small, light and heavy products. Using Conveyor line modules, a conveyor system or machine manufacturer can concentrate on more important tasks such as system integration, controls, installation and commissioning thus saving time and money. Contents RM 5504 Curve RM 5530 Merge RM 5550 45 Diverter RM 5545 90 Transfer RM 5591 4 4 6 8 10 12 Accessories 14 2 2015 interroll AG 3
RM 5504 Each zone is driven by a Drive that is connected to idler rollers via or s. Product benefits The internal control of the roller conveyor ensures transport of unit loads with zero pressure accumulation. 6 (mm) extrusion 3.15 (80mm) extrusion Combination of frame heights left/right 6 (mm) high, 2.6 (mm) above top of roller Allows lateral shifting 3.15 (80mm) high, 0.16 (5mm) below top of roller 3.15 /3.15 (80mm/80mm) 6 /6 (mm/mm) 3.15 /6 (80mm/mm) 6 /3.15 (mm/80mm) 80 5 L 2.17 (55mm) P ½ P SG Ø (48.26mm) SF = + 4.33 (110mm) General technical data Max. load capacity per zone 110 lb (50 kg) 175 lb (80 kg) Suitable without coated rollers Width () Module length (L) Zone lengths (ZL) pitch (P) ZL x number of zones up to 120 long 12, 18, 24, 30, 36, 48, 60 + 4.33 2 / 3 (50mm/75mm), 4 (100mm) 3.15 /6 (80mm/mm) 2.6 (mm) with 6 frame s.16 (5mm) higher than frame with 3.15 (80mm) frame material Max. number of rollers per zone Series 1700 Series 3500 Galvanized carbon steel 11 20 Drive 3/16 24VDC -to-roller 4 2015 interroll AG 5
P RM Curve 5504 RM 5530 The alignment of the material is maintained using tapered rollers. Product benefits curves change the direction of the load. 6 (mm) extrusion Combination of frame heights left/right 6 (mm) high, 2.6 (mm) above top of roller 6 /6 (mm/mm) 2.17 (55mm) α SF ½ Pi SG Pi = + 4.33 (110mm) ½ P 32.5 (825mm) General technical data Max. load capacity per zone 110 lb (50 kg) 175 lb (80 kg) Not suitable Width () Angle ( ) pitch, external (P) pitch, internal (Pi) + 4.33 (110mm) 30 /45 /60 /90 ~0.003 (~0.087mm) x + Pi ~2.83 (~72mm) 6 (mm) 2.6 (mm) material Max. number of rollers per zone Series 1700KXO Series 3500KXO Galvanized carbon steel with tapered polymer sleeves 9 Drive 3/16 24VDC -to-roller 6 2015 interroll AG 7
α RM Merge 5504 RM 5550 The Merge is used to merge two conveyor lines together. 6 (mm) extrusion 6 (mm) high, 2.6 (mm) above top of roller 2.17 (55mm) F 3.0 (76.2mm) T Ø (48.26mm) SF SG P ½ P ML General technical data Max. load capacity per zone material 110 lb (50 kg) 175 lb (80 kg) Not suitable Series 1700 Series 3500 Galvanized carbon steel Width () Width transfer (T) Max. module length (ML) Face length (F) Angle ( ) pitch, external (P) 60 (1,510mm) + 4.33 (110mm) Varies depending on application 30 /45 3 /4 (75mm/100mm) 6 (mm) 2.6 (mm) Drive 3/16 24VDC -to-roller 8 2015 interroll AG 9
RM 45 5504 Diverter RM 5545 The Diverter RM 5545 diverts material that should maintain its direction of travel using pivoting rollers. Product benefits This allows continuous and uninterrupted material flow. 6 (mm) extrusion F 3.0 (76.2mm) 6 (mm) high, 2.6 (mm) above top of roller T 2.17 (55mm) α Ø (48.26mm) SP SF ~ 14.37 (3mm) P ½ P ML General technical data Not suitable Series 1700 Series 3500 material Galvanized carbon steel Width () Width transfer (T) Max. module length (ML) Face length (F) Angle ( ) pitch, external (P) 60 (1,510mm) + 4.33 (110mm) Varies depending on application 45 3 /4 (75mm/100mm) 6 (mm) 2.6 (mm) Drive 3/16 -to-roller 10 2015 interroll AG 11
90 Transfer RM 5591 The 90 Transfer is a 24V DC right angle transfer that can be used both for merging and diverting. 6 (mm) extrusion 3.15 (80mm) extrusion 2.6 (mm) above top of roller Allows lateral shifting 0.16 (5mm) below top of roller 80 5 L C1 C2 C3 C4 40 230 Ø 50 75 T General technical data Not suitable Series 1700 Series 3500 material Galvanized carbon steel Width () Transfer width (T) Module length (L) Angle ( ) pitch (P) Length of diverter (ML) Varies depending on application + 4.33 (110mm) 90 3 /4 (75mm/100mm) Varies depending on application 3.15 /6 (80mm/mm) 2.6 (mm) with 6 frame s.16 (5mm) higher than frame with 3.15 (80mm) frame Drive 3/16 24VDC -to-roller Drive transfer Motor Max. electrical power Power transmission transfer 24 V gear motor Toothed bealt T10 12 2015 interroll AG 13
RM Accessories 5504 Belted zones and curves available for smaller items or when additional friction is required Support legs Lift gates Ceiling support brackets End caps 24V power supply unit(s) Photo cell kit End stops Transition plates Skewed roller sections also available for product alignment 14 14 2015 interroll AG 15
About Established in 1959 has grown to become the world s leading supplier of key products for intralogistics. Whether boxes, pallets or soft goods are to be handled, no other supplier has such a comprehensive range of products on offer. That is why system integrators, OEMs and operators select as their partner for their internal logistics business. Worldwide. The global network ensures quick delivery and superior service for every local customer. We inspire our customers and provide opportunities for them to increase efficiency. Corporation 3000 Corporate Drive Wilmington, NC 28405 Tel: Toll Free 1-800-830-9028 or (910) 799-1100 Fax (910) 799-9626 www.interroll.us reserves the right to modify the technical features of its products at any time. Technical information, volumes, data and features are only rough guidelines. 2015 EN/01.15/UM/PI-IV-2.0