SHOWER SYSTEM. Prefabricated Shower Substrates. Schluter Shower System

Transcription

1 I N N O VAT I V E S O L U T I O N S F O R C E R A M I C A N D S T O N E T I L E I N T E G R AT E D B O N D E D W AT E R P R O O F I N G S Y S T E M F O R T I L E D S H O W E R S The Schluter Shower System is an integrated family of products that together form a fully bonded, watertight assembly for tiled showers. Unlike shower pan liners in conventional assemblies, bonded waterproof membranes, such as Schluter -KERDI, bond directly to the mortar bed and protect it from becoming saturated with regular use. In addition, KERDI protects wall cavities from vapor penetration. The Schluter - KERDI-DRAIN provides a simple and secure connection to the KERDI membrane at the top of the assembly. Other components include the Schluter - KERDI-SEAL-PS/-MV prefabricated seals and the Schluter -KERDI-FIX sealant, used to treat protrusions through the membrane, and the Schluter -KERDI- SHOWER-ST/-SC/-SR prefabricated EPS substrates, which can reduce weight and installation time. The integrated Schluter Shower System eliminates the potential for leakage, efflorescence, and mold growth in the system, is maintenancefree, and dramatically reduces total installation time to ensure success and make shower installation easier than ever. Prefabricated Shower Substrates 8. Schluter -KERDI-SHOWER -ST/-SC/-SR Schluter prefabricated shower substrates provide an alternative to shower bases constructed of mortar. The shower tray, curb, and ramp are especially useful in Schluter Shower System Components Description KERDI-SHOWER-ST Shower tray 8" x 8", " x 0", or 7" x 7" KERDI-SHOWER-SC Shower curb KERDI Waterproofing membrane KERDI-BAND Waterproofing strip KERDI-DRAIN Drain, with integrated bonding flange KERDI-KERECK-F Pre-formed waterproofing corners ( inside and outside) Included with KERDI-DRAIN

2 large-scale, repetitive jobs, such as hotels, apartments, and condominiums for the significant timesavings that can be realized. Application and Function 8. Schluter -KERDI-SHOWER-ST/ -SC/-SR are prefabricated substrates, made of expanded polystyrene foam, for tiled shower bases in conjunction with Schluter -KERDI waterproofing membrane and Schluter -KERDI-DRAIN. Schluter -KERDI-SHOWER-ST is a prefabricated, sloped shower tray that is specifically designed to accept the Schluter -KERDI -DRAIN and Schluter -KERDI waterproofing membrane. The tray is available in 8" x 8" ( cm x cm), " x 0" (8 cm x cm), and 7" x 7" (8 cm x 8 cm) sizes. Schluter -KERDI -SHOWER-SC is a prefabricated curb that can be used with Schluter -KERDI -SHOWER-ST or conventional mortar applications. Curb dimensions are 8" x " x -/" ( cm x cm x. cm). Schluter -KERDI-SHOWER-SR is a ramp designed to facilitate the construction of access ramps for tiled showers. Ramp dimensions are 8" x -7/8" x -/" ( cm x 0 cm x.8 cm). Material Properties and Areas of Application Schluter -KERDI-SHOWER-ST/-SC/-SR are manufactured using lightweight expanded polystyrene (PS 0). The products require no special disposal and can be recycled. No CFCs or HCFCs are present in either the products or in the manufacturing process. The polystyrene foam has a density of.7 lb/ft ( kg/m ) with a 8 psi ( kpa) compressive strength at 0% deformation. It is serviceable in temperatures up to 7 F (79 C). The expanded polystyrene used to manufacture Schluter -KERDI-SHOWER- ST/-SC/-SR is treated with a flame retarding agent. The foam is self-extinguishing and achieves an HF- rating according to UL 9. Expanded polystyrene should not be exposed to hydrocarbons, esters, amines, and aldehydes. All will deteriorate foam. Exposure to ultraviolet rays (sunlight) for long periods of time will result in partial degradation (dusting) at the surface. 8. Schluter -KERDI-SHOWER-ST/-SC/-SR Property Method Density ASTM D7.7 lb/ft ( Kg/m ) Compressive Strength ASTM D7 & D 8 psi ( kpa) Linear Expansion ASTM D9. x 0 - / F Maximum Service Temperature - 7 F (79 C) Note:. Compressive strength measured at 0% deflection of foam Shower Waterproofing 8. Schluter -KERDI Since traditional shower pan liners are placed below the mortar setting bed in conventional assemblies, moisture is allowed to saturate the mortar bed. This can increase the risk of leakage, cause efflorescence, and foster mold growth. Bonded waterproof membranes, such as Schluter -KERDI, are set on top of the mortar bed and protect it from becoming saturated, thus eliminating the problems associated with traditional systems. Application and Function 8. Schluter -KERDI is a pliable, sheetapplied, bonded waterproof membrane and vapor retarder with limited crack-bridging capabilities. It is made of soft polyethylene, which is covered on both sides with a special fleece webbing to anchor the membrane in the thin-set mortar. Schluter -KERDI was developed as a waterproofing membrane to be used in conjunction with ceramic and stone tile coverings. Tiles can be installed directly on Schluter -KERDI using the thin-bed method. Other trowel-applied covering materials, such as plaster, can also be used. Various Schluter -KERDI accessories are available. KERDI-KERECK-F are pre-formed inside and outside corners. KERDI-SEAL- PS/-MV are prefabricated sections of KERDI with overmolded rubber gaskets that are used to seal pipe protrusions through the KERDI waterproofing membrane (e.g., at showerheads and tub spouts) and protect moisture-sensitive backing panels at the mixing valve. Use Schluter -KERDI-BAND, in widths of " (. cm), 7-/" (8. cm), or 0" ( cm), to seal butt joints or corner Value joints. Schluter -KERDI-FLEX, in " (. cm) or 0" ( cm) widths, is used to seal expansion joints or flexible edge joints. Material Properties and Areas of Application Schluter -KERDI is a polyethylene waterproofing membrane with a very low vapor permeance of 0.7 perms. The material is physiologically safe. Schluter -KERDI requires no special disposal. Schluter -KERDI is waterproof and resistant to most chemicals commonly encountered in tiled environments. It is resistant to aging and will not rot. Schluter -KERDI is highly resistant to saline solutions, acid and alkaline solutions, many organic solvents, alcohols, and oils. Information regarding its resistance to specific substances can be provided if concentration, temperature, and duration of exposure are known. For acidresistant coverings, use an epoxy adhesive to set and grout the tile. Schluter -KERDI is suitable for wall and floor surfaces where protection against the penetration of moisture or other harmful substances is necessary. Applications include showers, steam showers, tub surrounds, and areas surrounding swimming pools. Industrial applications include the food industry, breweries, and dairies. Before placing the Schluter -KERDI, verify that the substrate is clean, even, load bearing, and free from moisture. Surfaces that inhibit proper adhesion must be removed or appropriately treated. Schluter -KERDI meets the American National Standard for Load Bearing, Bonded, Waterproof Membranes for Thin-Set Ceramic Tile and Dimension Stone Installations (ANSI A8.0), is listed by cupc, and is evaluated by ICC-ES (see Report No. ESR-7). For copies of the listing and evaluation report, please contact Schluter -Systems at (800) 7-88 (USA) or (800) 7-87 (CAN) or by at info@schluter.com. Links to the

3 listing and report can also be accessed at Shower Drain 8. Schluter -KERDI-DRAIN Conventional two-stage drains are designed to connect to shower pan liners below the mortar bed and do not allow a secure, watertight connection to bonded waterproof membranes at the top of the drain assembly. The Schluter -KERDI -DRAIN was designed specifically to ensure a simple and secure connection to bonded waterproof membranes, such as Schluter -KERDI, at the top of the assembly rather than below it, thereby reducing the risk of leakage, efflorescence, and mold growth. Application and Function 8. Schluter -KERDI-DRAIN is a floor drain specifically designed to allow connections to Schluter -KERDI or other load-bearing, bonded waterproof membranes. Schluter -KERDI is adhered to the drain's large bonding flange to form a waterproof connection at the top of the drain assembly. KERDI-DRAIN features a fully adjustable grate to accommodate /" ( mm) to -/" ( mm) tile thicknesses. The grate assembly allows lateral and tilt adjustment as well. Material Properties and Areas of Application The drain casing is available in,, or stainless steel 0 (.0 = VA). The and drain casings feature a fleececovered bonding flange. They are available with standard " (0 mm) and " (7 mm) outlets and attached to and pipe, respectively, using or cement. The stainless steel drain casing features a standard " (7 mm) no-hub outlet and is attached to the pipe using an appropriate mechanical (e.g., flexible or no-hub) coupling. The simple connection to standard drain outlets makes KERDI-DRAIN suitable for new construction and renovation. The height adjustment collar and lateral adjustment ring are made of either for use with the plastic drain casings featuring " (0 mm) outlets or stainless steel for use with the stainless steel drain casing and the plastic drain casings featuring " (7 mm) outlets. The grate is available in stainless steel 0 (.0 = VA) and in anodized aluminum with a brushed copper bronze, brushed brass, or brushed nickel finish. Various configurations of the Schluter -KERDI- DRAIN are listed by UPC, CSA, and NSF. Please refer to the table on page 8 for details. Relevant industry standard guidelines for floor drains with integrated bonding flange include method B in the Tile Council of North America's (TCNA) Handbook for Ceramic Tile Installation and Method DR in the Terrazzo, Tile and Marble Association of Canada (TTMAC) Specification Guide 0900 Tile Installation Manual. Maintenance Schluter -KERDI-DRAIN requires no special maintenance and is resistant to mold and fungi. The grate may be removed to clean the drain housing and the drainpipes. Clean the grate using common household cleaning agents. Stainless steel grates exposed to the environment or aggressive substances should be cleaned periodically using a mild household cleaner. Regular cleaning maintains the neat appearance of stainless steel and reduces the risk of corrosion. All cleaning agents must be free of hydrochloric and hydrofluoric acid. Stainless steel surfaces develop a sheen when treated with a chrome-polishing agent. In the case of the anodized aluminum grates, do not use abrasive or alkaline cleaning agents. Adhesive/Sealant Any protrusions through the KERDI membrane can be treated with Schluter -KERDI-FIX, or equivalent sealant, to ensure a fully waterproof assembly. Application and Function 8. Schluter -KERDI-FIX 8. Schluter -KERDI-FIX is a singlecomponent, waterproof sealing and Schluter -KERDI-FIX Technical Data Color Grey or bright white Basic raw material Silyl-modified polymer (SMP) Specific weight approx. 9. lb/ft (. g/ml) Solvent content 0% Isocyanate content 0% Dry materials content approx. 00% Shear strength beech wood/ approx. psi ( N/mm ) beech wood Shear strength aluminum/ approx. 90 psi ( N/mm ) aluminum Elongation at failure approx. 00% Skinning about 0 minutes Curing /8" ( mm) per hours Permissible total movement about 0% Processing temperatures don t install at temperatures below 0 ºF ( ºC) Temperature stability -0 ºF (-0 ºC) to ºF (00 ºC), temporarily ºF (80 ºC) [max. 0 minutes] Moisture resistance very good Frost ability not sensitive to frost Cartridge volume 9.8 oz (90 ml) Estimated coverage " (.7 cm) connection to ' 0" (.9 m) per cartridge fixed building elements /" bead 0' " (9. m) per cartridge

4 bonding compound with a silane-modified polymer base, which can be used in various applications. In conjunction with Schluter -KERDI, Schluter -KERDI-FIX can be used to waterproof pipe and valve protrusions in the Schluter Shower System. KERDI-FIX is used to bond the KERDI membrane to the stainless steel Schluter -KERDI-DRAIN bonding flange. Schluter -KERDI-FIX can also be used to bond Schluter -KERDI to building elements such as balcony and terrace doors, window elements, sheet metal covers, and Schluter -BARA edge profiles, and is suitable for sealing movement joints. Material Properties and Areas of Application Schluter -KERDI-FIX is odorless, weather and UV resistant, making it especially suitable for exterior use. The product is elastomeric, free of solvents, and provides a strong bond to most materials, including wood, stone, concrete, metal, glass, and many synthetic materials. Schluter -KERDI-FIX can be painted over with most alkyd resins or dispersion paint types. The suitability of the material must be verified based on the anticipated chemical, mechanical, and/or other stresses. Maintenance Storage Unopened packages of Schluter -KERDI -FIX can be stored in a cool place for up to 8 months. Once the cartridge has been opened, the material has a limited shelf life. System Installation Shower Bases Constructed with Schluter Prefabricated Shower Substrates. The substrate must be clean, even, and load bearing. Any leveling must be done prior to placing the tray. If necessary, cut the KERDI-SHOWER- ST tray to size prior to application. Ideally, the tray should be cut by equal amounts on all four sides to ensure a consistent height of the first course of tile. The shower base can also be extended beyond the tray using dry- pack mortar. After locating the correct position (use KERDI-SHOWER-ST as a template), cut a hole in the substrate for the drain.. Apply unmodified thin-set mortar to the substrate using a /" x /8" ( mm x 0 mm) square- or U-notched trowel. Place the KERDI-SHOWER-ST, making certain to solidly embed the tray in the mortar. Check the underside of the tray to ensure that full coverage is achieved.. If necessary, cut the KERDI-SHOWER -SC to length with a handsaw. Apply unmodified thin-set mortar to the floor and to the edge of the shower tray using a /" x /8" ( mm x 0 mm) square- or U-notched trowel, and press the curb firmly into place.. If there is access to the plumbing from below and the waste line can be connected after installing Schluter -KERDI-DRAIN, apply unmodified thinset mortar to completely fill the step in the shower tray. Press Schluter -KERDI-DRAIN firmly into the mortar, ensuring full support of the bonding flange. When job conditions require the setting of Schluter -KERDI-DRAIN by the plumber prior to the installation of the Schluter -KERDI-SHOWER-ST tray (or when there is no access to the plumbing from below), install the KERDI-DRAIN to the appropriate height using the detachable center section of the tray or the foam spacers included with the drain. Before installing the Schluter -KERDI-SHOWER-ST tray, apply thin-set mortar to the substrate and to the top and bottom of the detached center section. Slide the center section into place below the drain to ensure solid and uniform support of the bonding flange. Note: Schluter -Systems recommends installing the KERDI-SHOWER-ST tray prior to setting KERDI-DRAIN whenever possible. This method affords the installer greater control over the final position of the drain and makes it easier to obtain full support under the bonding flange.. Apply a bond coat of unmodified thinset mortar to the tray using a /" x /" ( mm x mm) V-notched or the Schluter -KERDI-TROWEL, which features a /8" X /8" ( mm x mm) square-notched design. When using the plastic drain casing, apply additional unmodified thin-set mortar to the bonding flange with a /" x /" ( mm x mm) V-notched or the Schluter -KERDI-TROWEL, which features a /8" X /8" ( mm x mm) square-notched design. When using the stainless steel drain casing, the Schluter -KERDI waterproofing membrane is bonded to the integrated bonding flange with the Schluter - KERDI-FIX adhesive/sealant. The stainless steel bonding flange must be clean and free of grease or other contaminants prior to KERDI-FIX application. Embed Schluter -KERDI in the bond coat and work the membrane onto the entire surface to ensure full coverage and remove air pockets. The KERDI is carried to the step in the bonding flange (template provided). Be sure the connection between the KERDI and KERDI-DRAIN is secure. Note: A sheet of cardboard can be placed on the floor to protect the KERDI during subsequent steps.. Construct floor/wall, floor/curb, and wall/wall connections using Schluter -KERDI-BAND or cut sections of KERDI. Seams are easily constructed by overlapping the edges of KERDI or KERDI-BAND by " (0 mm) using an unmodified thin-set mortar. 7. Seal the shower curb/wall junction and other corners using Schluter -KERDI- KERECK-F pre-formed inside and outside corners and unmodified thinset mortar. 8. Apply a bond coat of unmodified thinset mortar to the shower walls and curb using a /" x /" ( mm x mm) V-notched or the Schluter -KERDI- TROWEL, which features a /8" x /8" ( mm x mm) square-notched design. Embed the KERDI in the thin-set mortar and work the membrane onto the entire surface to ensure full coverage and remove air pockets. The KERDI is carried to the height of the shower head (at minimum). Note: The thin-set mortar used for bonding Schluter -KERDI to the walls must be appropriate for the substrate and must penetrate and engage the KERDI fleece. For most substrates (e.g., drywall or CBU), an unmodified

5 thin-set mortar is used. Seams in the membrane are constructed by overlapping the edges of KERDI by " (0 mm) with unmodified thin-set mortar or by abutting adjacent sheets of KERDI and installing KERDI-BAND with unmodified thin-set mortar, centered over the joint. Note: Any protrusions through the KERDI membrane (e.g., mixing valve, shower head, etc.) must be treated with Schluter -KERDI-SEAL-PS/-MV, Schluter -KERDI-FIX, or equivalent sealant, to ensure a watertight seal. 9. Once the entire membrane, including seams, corners, curbs, and connection to drain, have been completely bonded and, therefore, waterproofed, the assembly is ready to be tiled. The sequence of membrane installation can vary from the steps above (i.e., topover-bottom or shingle laps are not required), provided that the minimum " (0 mm) overlap is maintained at all joints and proper connection to the drain is established. Note: Prior to setting tile, if the assembly is to be water tested, wait hours to allow for final set of the mortar before testing to ensure waterproof performance of the assembly at seams and connections. 0. The grate assembly, which is comprised of the grate, the height adjustment collar, and the lateral adjustment ring, is set with unmodified thin-set mortar. The height of the grate is adjusted via the height adjustment collar and aligned flush with the top of the tile covering. Since the diameter of the height adjustment collar is smaller than the opening of the bonding flange, the grate can be positioned to match the joint pattern of the tile covering. Note: Protect the visible surface of the grate from contact with setting and grouting materials. In particular, anodized aluminum is sensitive to alkaline materials.. Apply unmodified thin-set mortar directly to the exposed Schluter -KERDI surface and install the tiles, ensuring full coverage. For acidresistant coverings, use an epoxy adhesive to set and grout the tile. Shower Bases Constructed with Mortar a. If there is access to the plumbing from below, and the waste line will be connected subsequent to installing Schluter -KERDI-DRAIN, the drain can be firmly embedded in a ring of loose mortar and leveled before placing the screed. b. When job conditions require the setting of the KERDI-DRAIN by the plumber prior to the installation of the mortar bed (or when there is no access to the plumbing from below), connect the drain to the waste line at the desired height. Pack loose mortar under the bonding flange and drain casing, such that the unit is fully supported, before placing the screed. When installing KERDI-DRAIN over wood substrates, the minimum thickness of mortar required at the perimeter of the bonding flange is " ( mm). Note: Schluter -Systems recommends installing the KERDI-DRAIN according to step a above whenever possible. This method affords the installer greater control over the final position of the drain and makes it easier to obtain full support under the bonding flange.. The screed is then placed flush with the top of the bonding flange of the KERDI- DRAIN. Slope the mortar bed using the bonding flange and a perimeter screed as guides.. As soon as the mortar can be walked upon, apply a bond coat of unmodified thin-set mortar to the screed using a /" x /" ( mm x mm) V-notched or the Schluter -KERDI-TROWEL, which features a /8" x /8" ( mm x mm) square-notched design. When using the plastic drain casing, apply additional unmodified thin-set mortar to the bonding flange with a /" x /" ( mm x mm) V-notched or the Schluter -KERDI-TROWEL, which features a /8" x /8" ( mm x mm) square-notched design. When using the stainless steel drain casing, the Schluter -KERDI waterproofing membrane is bonded to the integrated bonding flange with the Schluter - KERDI-FIX adhesive/sealant. The stainless steel bonding flange must be clean and free of grease or other contaminants prior to KERDI-FIX application. Embed Schluter -KERDI in the bond coat and work the membrane onto the entire surface to ensure full coverage and remove air pockets. The KERDI is carried to the step in the bonding flange (template provided). Be sure the connection between the KERDI and KERDI-DRAIN is secure. Note: A sheet of cardboard can be placed on the floor to protect the KERDI during subsequent steps.. Construct floor/wall, floor/curb, and wall/wall connections using Schluter -KERDI-BAND or cut sections of KERDI. Seams are easily constructed by overlapping the edges of KERDI or KERDI-BAND by " (0 mm) using an unmodified thin-set mortar.. Seal the shower curb/wall junction and other corners using Schluter -KERDI -KERECK-F inside and outside corners and unmodified thin-set mortar.. Apply a bond coat of unmodified thinset mortar to the shower walls and curb using a /" x /" ( mm x mm) V-notched or the Schluter -KERDI- TROWEL, which features a /8" X /8" ( mm x mm) square-notched design. Embed the KERDI in the thin-set mortar and work the membrane onto the entire surface to ensure full coverage and remove air pockets. The KERDI is carried to the height of the showerhead (at minimum). Note: The thin-set mortar used for bonding Schluter -KERDI to the walls and curb must be appropriate for the substrate and must penetrate and engage the KERDI fleece. For most substrates (e.g., drywall or CBU), an unmodified thin-set mortar is used. Seams in the membrane are constructed by overlapping the edges of KERDI by " (0 mm) with unmodified thin-set mortar or by abutting adjacent sheets of KERDI and installing KERDI- BAND with unmodified thin-set mortar, centered over the joint. Note: Any protrusions through the KERDI membrane (e.g., mixing valve, shower head, etc.) must be treated with Schluter -KERDI-SEAL-PS/-MV, Schluter -KERDI-FIX, or equivalent sealant, to ensure a watertight seal. 7. Once the entire membrane, including seams, corners, curbs, and connection

6 to drain, have been completely bonded and, therefore, waterproofed, the assembly is ready to be tiled. The sequence of membrane installation can vary from the steps above (i.e., topover-bottom or shingle laps are not required) provided that the minimum " (0 mm) overlap is maintained at all joints and proper connection to the drain is established. Note: Prior to setting tile, if the assembly is to be water tested, wait hours to allow for final set of the mortar before testing to ensure waterproof performance of the assembly at seams and connections. 8. The grate assembly, which is comprised of the grate, the height adjustment collar, and the lateral adjustment ring, is set with unmodified thin-set mortar. The height of the grate is adjusted via the height adjustment collar and aligned flush with the top of the covering. Since the diameter of the height adjustment collar is smaller than the opening of the bonding flange, the grate can be positioned to match the joint pattern of the tile covering. Note: Protect the visible surface of the grate from contact with setting and grouting materials. In particular, anodized aluminum is sensitive to alkaline materials. 9. Apply unmodified thin-set mortar directly to the exposed Schluter -KERDI surface and install the tiles, ensuring full coverage. For acidresistant coverings, use an epoxy adhesive to set and grout the tile. Product Item Numbers 8. Schluter -KERDI-SHOWER-ST (prefabricated EPS tray) Width Length Perimeter Height Drain Placement ST- 8" cm 8" cm -/".8 cm Center ST-8/ " 8 cm 0" cm -/". cm Center ST-8/ BR " 8 cm 0" cm -/".8 cm Off-center* ST-8 7" 8 cm 7" 8 cm -/".8 cm Center *Off-center drain at 0" ( cm) from end 8. Schluter -KERDI-SHOWER-SC (prefabricated EPS curb) Width Length Height SC- -/". cm 8" cm " cm 8. Schluter -KERDI-SHOWER-SR (prefabricated EPS ramp) Width Length Height SR- 8" cm -7/8" 0 cm -/".8 cm 8. Schluter -KERDI (waterproofing membrane) Width Length Area KERDI 00/M ' " m ' " m ft m 8 mil KERDI 00/0M ' " m ' 0 m 08 ft 0 m 8 mil KERDI 00 ' " m 98' " 0 m ft 0 m 8 mil 8. Schluter -KERDI-BAND (waterproofing strips) Width Length KEBA 00//M ". cm ' " m mil KEBA 00//0M ". cm ' 0 m mil KEBA 00/8/M 7-/" 8. cm ' " m mil KEBA 00/0/M 0" cm ' " m mil KEBA 00/ ". cm 98' " 0 m mil KEBA 00/8 7-/" 8. cm 98' " 0 m mil KEBA 00/0 0" cm 98' " 0 m mil

7 8. Schluter -KERDI-FLEX (waterproofing strips for use above movement joints) Width Length FLEX /M ". cm ' " m mil FLEX 0/M 0" cm ' " m mil FLEX /0 ". cm 98' " 0 m mil FLEX 0/0 0" cm 98' " 0 m mil 8. Schluter -KERDI-KERECK-F (pre-formed corners) Packaging KERECK / FI mil Inside corners KERECK / FI 0 mil 0 Inside corners KERECK / FA mil Outside corners KERECK / FA 0 mil 0 Outside corners 8. Schluter -KERDI-SEAL-PS (pipe seal with over-molded rubber gasket) KMS8/ KMS8/0 KMS08/ KMS08/0 Pipe nipple opening diam. /" -. mm /" - 0 mm /" -. mm /" - 0 mm mil mil mil mil Packaging unit unit 0 units 0 units 8. Schluter -KERDI-SEAL-MV (mixing valve seal with over-molded rubber gasket) KMSMV/ KMSMV0/ Mixing valve opening diam. -/" - mm -/" - mm mil mil Packaging unit 0 units 8. Schluter -KERDI-KM (pipe collar) Dimensions Packaging KM 7/ 7" x 7" - 7 cm x 7 cm mil units Hole diameter, ø = 7/8" - mm Schluter -KERDI-TROWEL Notch Size Packaging TRL-KER /8" x /8" ( mm x mm) units 8. Schluter -KERDI-FIX (sealant) Cartridge Volume KERDIFIX / color* 9.8 oz (90 ml) *Color Codes BW Bright white G Grey To complete the item number, add the color code (e.g., KERDIFIX / BW). 7

8 8. Schluter -KERDI-DRAIN Flanges A B C / flange with " (0 mm) drain outlet / flange with " (7 mm) drain outlet Stainless steel flange with " (7 mm) no-hub outlet " " (00 mm) Square Grate Square Grate " (0 mm) Round Grate E ATGB AKGB AMGB Stainless steel (E) Brushed brass anod. alu. (AMGB) Brushed copper/bronze anod. alu. (AKGB) A Floor drain, with integrated bonding flange with " (0 mm) outlet Brushed nickel anod. alu. (ATGB) KD//E KD//AMGB KD//AKGB KD//ATGB KD//E KD//RE KD//E KD//AMGB KD//AKGB KD//ATGB KD//E KD//RE B Floor drain, with integrated bonding flange with " (7 mm) outlet C KD//E KD//RE KD//E KD//RE Floor drain, with integrated bonding flange with " (7 mm) no-hub outlet Stainless Steel KD/E/E KD/E/AMGB KD/E/AKGB KD/E/ATGB KD/E/E KD/E/RE Drain casing is available in (black), (grey), or Stainless Steel. All other components are made of, except where otherwise indicated. Note: The drain assemblies include inside and outside KERDI-KERECK corners. Stainless steel (E) Stainless steel (E) E " " Schluter -KERDI-DRAIN Product Listings Flange Grate UPC CSA NSF " / " Stainless Steel X X X " / " Anod. Alu. X X X Components for / flange with " (0 mm) drain outlet and " (00 mm) grate /" - mm -/" - 00 mm /" - 9 mm E " / " Stainless Steel X " / " Stainless Steel Stainless Steel " Stainless Steel X X -/8" - 8 mm -/8" - 9 mm -7/" - 7 mm Stainless Steel " Anod. Alu. X X Stainless Steel " Stainless Steel X X -/" - 7 mm -/" - 9 mm Product Standards: UPC - IAPMO IGC 9 CSA - CSA B79 NSF - Special engineered product (SE) For copies of the above listings, please contact Schluter - Systems at (800) 7-88 (USA) or (800) 7-87 (CAN) or by at info@schluter.com. Links to the above listings can also be accessed at -/" - 9 mm -/" - 00 mm -/" - 0 mm -7/8" - 98 mm 7/8" - mm -9/" - 9 mm 8 Note: Stainless steel, Phillips head screws are included with KERDI-DRAIN. If you require tamper-proof screws, please see the table below. Tamper-proof screws Description (for grate) Packaging KD/TPSCRW Tamper-proof screw unit KD/TPWRCH Wrench unit -/8" - 7 mm -/" - 09 mm Grate (Stainless steel, Brushed nickel anodized aluminum, Brushed copper/bronze anodized aluminum, Brushed brass anodized aluminum) Height adjustment collar Lateral adjustment ring Drain casing with fleece-laminated bonding flange

9 8" ( cm) Schluter -KERDI-SHOWER-KIT (8" x 8" center drain tray) 8" ( cm) Components with Stainless steel grate (E 0) (.0 = VA) KKE Description Specify material for drain ( or ) and grate finish Materials Quantity KERDI-SHOWER-ST Shower tray, 8" x 8" ( cm x cm) KERDI-SHOWER-SC Shower curb, 8" x " x -/" ( cm x cm x. cm) KERDI Waterproofing membrane, ' " x ' ( m x 0 m) KERDI-BAND Waterproofing strip, " x ' ( mm x 0 m) KERDI-DRAIN Drain, with integrated bonding flange KERDI-KERECK-F Inside corners Outside corners Note: Drain casing is available in (black) or (grey). All other components are made of, except where otherwise indicated. KKE with Brushed nickel anodized aluminum grate (ATGB) KKATGB KKATGB with Brushed copper/bronze anodized aluminum grate (AKGB) KKAKGB KKAKGB with Brushed brass anodized aluminum grate (AMGB) KKAMGB KKAMGB 7" (8 cm) Schluter -KERDI-SHOWER-KIT (7" x 7" center drain tray) 7" (8 cm) Components Description Quantity KERDI-SHOWER-ST Shower tray, 7" x 7" (8 cm x 8 cm) KERDI-SHOWER-SC Shower curb, 8" x " x -/" ( cm x cm x. cm) KERDI Waterproofing membrane, ' " x ' ( m x 0 m) KERDI-BAND Waterproofing strip, " x ' ( mm x 0 m) KERDI-DRAIN Drain, with integrated bonding flange KERDI-KERECK-F Inside corners Outside corners Specify material for drain ( or ) and grate finish with Stainless steel grate (E 0) (.0 = VA) Materials Note: Drain casing is available in (black) or (grey). All other components are made of, except where otherwise indicated. KK8E KK8E with Brushed nickel anodized aluminum grate (ATGB) KK8ATGB KK8ATGB with Brushed copper/bronze anodized aluminum grate (AKGB) KK8AKGB KK8AKGB with Brushed brass anodized aluminum grate (AMGB) KK8AMGB KK8AMGB 9

10 " (8 cm) Schluter -KERDI-SHOWER-KIT (" x 0" center drain tray) Components Description Quantity 0" ( cm) 0" ( cm) " (8 cm) KERDI-SHOWER-ST Shower tray, " x 0" (8 cm x cm) KERDI-SHOWER-SC Shower curb, 8" x " x -/" ( cm x cm x. cm) KERDI Waterproofing membrane, ' " x ' ( m x 0 m) KERDI-BAND Waterproofing strip, " x ' ( mm x 0 m) KERDI-DRAIN Drain, with integrated bonding flange KERDI-KERECK-F Inside corners Outside corners Specify material for drain ( or ) and grate finish with Stainless steel grate (E 0) (.0 = VA) KK8E KK8E with Brushed nickel anodized aluminum grate (ATGB) KK8ATGB KK8ATGB with Brushed copper/bronze anodized aluminum grate (AKGB) KK8AKGB KK8AKGB with Brushed brass anodized aluminum grate (AMGB) KK8AMGB KK8AMGB Schluter -KERDI-SHOWER-KIT (" x 0" off-center drain tray) Components Description Materials Quantity KERDI-SHOWER-ST Shower tray, " x 0" (8 cm x cm) KERDI-SHOWER-SC Shower curb, 8" x " x -/" ( cm x cm x. cm) KERDI Waterproofing membrane, ' " x ' ( m x 0 m) KERDI-BAND Waterproofing strip, " x ' ( mm x 0 m) KERDI-DRAIN Drain, with integrated bonding flange KERDI-KERECK-F Inside corners Outside corners Note: Drain casing is available in (black) or (grey). All other components are made of, except where otherwise indicated. Note: Tray features offcenter drain placement: 0" (. cm) o.c. from end of tray. Specify material for drain ( or ) and grate finish Materials with Stainless steel grate (E 0) (.0 = VA) KKB8E KKB8E with Brushed nickel anodized aluminum grate (ATGB) KKB8ATGB KKB8ATGB with Brushed copper/bronze anodized aluminum grate (AKGB) KKB8AKGB KKB8AKGB with Brushed brass anodized aluminum grate (AMGB) KKB8AMGB KKB8AMGB Note: Drain casing is available in (black) or (grey). All other components are made of, except where otherwise indicated. 0

11 8. Schluter -KERDI and 8. Schluter -KERDI-DRAIN are used to waterproof a shower installation. The assembly is ready for tile setting. The 8. Schluter -KERDI-DRAIN grate assembly accommodates /" ( mm) to -/" ( mm) -thick tiles and features both lateral and tilt adjustment. The Schluter Shower System eliminates the potential for leakage, efflorescence, and mold growth to ensure that tiled showers remain beautiful and functional over time.

12 Schluter Systems L.P. 9 Pleasant Ridge Road, Plattsburgh, NY 90-8 Tel.: Fax: info@schluter.com w w w. s c h l u t e r. c o m Schluter Systems (Canada) Inc. Thimens Blvd., St-Laurent, QC HR K9 Tel.: Fax: info@schluter.com Item number: CSSHOWERSYS Date: 0/009 Printed in CANADA 009 Schluter Systems L.P.