SOUTH AFRICAN NATIONAL STANDARD
|
|
- Rodney Webster
- 6 years ago
- Views:
Transcription
1 ISBN SOUTH AFRICAN NATIONAL STANDARD Electric welded low carbon steel pipes for aqueous fluids (large bore) Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001 Tel: Fax: SABS
2 Table of changes Change No. Date Scope Amdt Amended to change the designation of SABS standards to SANS standards and to update the definition of "acceptable". Amdt Amended to update referenced standards, and to update the requirements in the table on chemical composition and physical properties of steels. Acknowledgement The SABS Standards Division wishes to acknowledge the valuable assistance derived from publications of the following organizations: American Petroleum Institute British Standards Institute Deutscher Normenausschuss Foreword This South African standard was approved by National Committee SABS/TC 138/SC 04, Water and sanitation Equipment and systems Metallic pipes and fittings, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This document was published in August This document supersedes SANS 719:2008 (edition 3.1). A vertical line in the margin shows where the text has been technically modified by amendment No. 2. Annex A forms an integral part of this document. Annex B is for information only. Compliance with this document cannot confer immunity from legal obligations. Reaffirmed and reprinted in February This document will be reviewed every five years and be reaffirmed, amended, revised or withdrawn.
3 Contents Page Acknowledgement Foreword 1 Scope Normative references Definitions Material requirements General requirements Inspection and methods of test Inspection Destructive tests Hydraulic test Coatings and linings Marking Figures 1 to Annex A (normative) Notes to purchasers Annex B (informative) Quality verification of electric welded low carbon steel pipes Bibliography
4 This page is intentionally left blank 2
5 Electric welded low carbon steel pipes for aqueous fluids (large bore) 1 Scope This standard covers three grades of carbon steel pipes of size 219,1 mm to mm used in the conveyance of water and other aqueous fluids. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this standard. All standards are subject to revision, and since any reference to a standard is deemed to be a reference to the latest edition of that standard, parties to agreements based on this standard are encouraged to take steps to ensure the use of the most recent editions of the standards indicated below. Information on currently valid national and international standards can be obtained from the SABS Standards Division. SANS 32/EN 10240, Internal and/or external protective coatings for steel tubes Specification for hot dip galvanized coatings applied in automatic plants. SANS 121/ISO 1461, Hot dip galvanized coatings on fabricated iron and steel articles Specifications and test methods. SANS 1178, The production of lined and coated steel pipes using fibre reinforced bituminous materials. SANS 1217, Internal and external organic coating protection for buried steel pipelines. SANS /ISO , Metallic materials Tensile testing Part 1: Method of test at room temperature. Amdt 2 SANS , Welding Part 1: Glossary of terms. 3 Definitions For the purposes of this specification, the definitions given in SANS and the following definitions shall apply: 3.1 acceptable acceptable to the authority administering this standard, or to the parties concluding the purchase contract, as relevant Amdt 1 3
ISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 14713-2 First edition 2009-12-15 Zinc coatings Guidelines and recommendations for the protection against corrosion of iron and steel in structures Part 2: Hot dip galvanizing
More informationAustralian Standard. Qualification of welders for fusion welding of steels AS AS
AS 2980 2004 AS 2980 2004 Australian Standard Qualification of welders for fusion welding of steels This Australian Standard was prepared by Committee WD-003, Welding of Structures. It was approved on
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 8535-1 Fourth edition 2006-08-01 Diesel engines Steel tubes for highpressure fuel injection pipes Part 1: Requirements for seamless cold-drawn single-wall tubes Moteurs diesels
More informationAS/NZS 2280:2012 AS/NZS
AS/NZS 2280:2014 Incorporating Amendment No. 1 and 2 Australian/New Zealand Standard Ductile iron pipes and fittings Superseding AS/NZS 2280:2012 AS/NZS 2280:2014 AS/NZS 2280:2014 This joint Australian/New
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 10893-2 First edition 2011-04-01 Non-destructive testing of steel tubes Part 2: Automated eddy current testing of seamless and welded (except submerged arc-welded) steel tubes
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 15614-2 First edition 2005-05-15 Specification and qualification of welding procedures for metallic materials Welding procedure test Part 2: Arc welding of aluminium and its
More informationMetallic products Types of inspection documents
BRITISH STANDARD BS EN 10204:2004 Metallic products Types of inspection documents The European Standard EN 10204:2004 has the status of a British Standard ICS 01.110; 77.080.01; 77.120.01 BS EN 10204:2004
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 15761 First edition 2002-12-15 Steel gate, globe and check valves for sizes DN 100 and smaller, for the petroleum and natural gas industries Robinets-vannes, robinets à soupape
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 15614-8 Second edition 2016-03-01 Specification and qualification of welding procedures for metallic materials Welding procedure test Part 8: Welding of tubes to tube-plate joints
More informationISO 1401 INTERNATIONAL STANDARD. Rubber hoses for agricultural spraying. Tuyaux en caoutchouc pour pulvérisation agricole. Third edition
INTERNATIONAL STANDARD ISO 1401 Third edition 1999-12-01 Rubber hoses for agricultural spraying Tuyaux en caoutchouc pour pulvérisation agricole A Reference number ISO 1401:1999(E) ISO 1401:1999(E) Contents
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 21138-3 First edition 2007-10-15 Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride)
More informationISO 642 INTERNATIONAL STANDARD. Steel Hardenability test by end quenching (Jominy test) Acier Essai de trempabilité par trempe en bout (essai Jominy)
INTERNATIONAL STANDARD ISO 642 Second edition 1999-09-01 Steel Hardenability test by end quenching (Jominy test) Acier Essai de trempabilité par trempe en bout (essai Jominy) A Reference number ISO 642:1999(E)
More informationThis is a free 15 page sample. Access the full version online. HB 90.1:2012 The Small Business Handbook Guide to ISO 9001:2008
This is a free 15 page sample. Access the full version online. HB 90.1:2012 The Small Business Handbook Guide to ISO 9001:2008 HB This is a free 15 page sample. Access the full version online. HB 90.1:2012
More informationISO INTERNATIONAL STANDARD. Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries
INTERNATIONAL STANDARD ISO 10434 Second edition 2004-07-15 Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries Robinets-vannes en acier à chapeau boulonné pour les industries
More informationISO INTERNATIONAL STANDARD. Metallic and other inorganic coatings Electrodeposited zinc alloys with nickel, cobalt or iron
INTERNATIONAL STANDARD ISO 15726 First edition 2009-02-01 Metallic and other inorganic coatings Electrodeposited zinc alloys with nickel, cobalt or iron Revêtements métalliques et autres revêtements inorganiques
More informationISO INTERNATIONAL STANDARD. Petroleum, petrochemical and natural gas industries Hairpin-type heat exchangers
INTERNATIONAL STANDARD ISO 12212 First edition 2012-08-01 Petroleum, petrochemical and natural gas industries Hairpin-type heat exchangers Industries du pétrole et du gaz naturel Échangeurs thermiques
More informationAS/NZS :2014. Guide to the protection of structural steel against atmospheric corrosion by the use of protective coatings AS/NZS 2312.
Australian/New Zealand Standard AS/NZS 2312.1:2014 Guide to the protection of structural steel against atmospheric corrosion by the use of protective coatings Part 1: Paint coatings Superseding AS/NZS
More informationAustralian Standard. Cement mortar lining of steel pipes and fittings AS AS 1281
AS 1281 2001 AS 1281 Australian Standard Cement mortar lining of steel pipes and fittings This Australian Standard was prepared by Committee WS-009, Rolled and Welded Steel Pipes. It was approved on behalf
More informationAWS B2.1/B2.1M-BMG:2009. Base Metal Grouping for Welding Procedure and Performance Qualification
Base Metal Grouping for Welding Procedure and Performance Qualification Base Metal Grouping for Welding Procedure and Performance Qualification Prepared by the American Welding Society (AWS) B2 Committee
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 27769 First edition 2016-12-15 Wood-based panels Wet process fibreboard Panneaux à base de bois Panneau de fibres obtenu par procédé humide Reference number ISO 27769:2016(E)
More informationPIP STF05520 Details for Pipe Railing for Walking and Working Surfaces
TECHNICAL CORRECTION January 2017 Structural PIP STF05520 Details for Pipe Railing for Walking and Working Surfaces PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES In an effort to minimize the cost of process
More informationISO 5178 INTERNATIONAL STANDARD. Destructive tests on welds in metallic materials Longitudinal tensile test on weld metal in fusion welded joints
INTERNATIONAL STANDARD ISO 5178 First edition 2001-02-01 Destructive tests on welds in metallic materials Longitudinal tensile test on weld metal in fusion welded joints Essais destructifs des soudures
More informationDEUTSCHE NORM December 2000
DEUTSCHE NORM December 2000 Tape and shrinkable materials for the corrosion protection of buried or underwater pipelines without cathodic protection for use at operating temperatures up to 50 C { 30672
More informationISO INTERNATIONAL STANDARD. Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques Règles générales
INTERNATIONAL STANDARD ISO 15607 First edition 2003-12-15 Specification and qualification of welding procedures for metallic materials General rules Descriptif et qualification d'un mode opératoire de
More informationAustralian Standard. Equipment for the pasteurization of milk and other liquid dairy products Continuous-flow systems AS AS 3993
AS 3993 2003 AS 3993 Australian Standard Equipment for the pasteurization of milk and other liquid dairy products Continuous-flow systems This Australian Standard was prepared by Committee FT-012, Dairy
More informationFlat products made of steels for pressure purposes
BRITISH STANDARD BS EN 10028-4:2003 Flat products made of steels for pressure purposes Part 4: Nickel alloy steels with specified low temperature properties The European Standard EN 10028-4:2003 has the
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 1452-3 First edition 2009-12-01 Corrected version 2010-03-01 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure Unplasticized
More informationAustralian Standard. Pipelines Gas and liquid petroleum. Part 0: General requirements AS AS
AS 2885.0 2008 AS 2885.0 2008 Australian Standard Pipelines Gas and liquid petroleum Part 0: General requirements This Australian Standard was prepared by Committee ME-038, Petroleum Pipelines. It was
More informationISO INTERNATIONAL STANDARD. Founding Ausferritic spheroidal graphite cast irons Classification
INTERNATIONAL STANDARD ISO 17804 First edition 2005-11-01 Founding Ausferritic spheroidal graphite cast irons Classification Fonderie Fonte ausferritique à graphite sphéroïdal Classification Reference
More informationSpecification for Welding of Tanks, Vessels, and Other Equipment in Sanitary (Hygienic) Applications
An American National Standard Specification for Welding of Tanks, Vessels, and Other Equipment in Sanitary (Hygienic) Applications Key Words Visual examination acceptance criteria, food processing equipment,
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 12686 First edition 1999-12-01 Metallic and other inorganic coatings Automated controlled shot-peening of metallic articles prior to nickel, autocatalytic nickel or chromium
More informationDRAFT UGANDA STANDARD
DRAFT UGANDA STANDARD DUS1910-2 First Edition 2017-10-20 Metal Chairs for 0ffice Purposes Part. 2: Revolving and Tilting- Specification Reference number DUS 1910-2:2017 UNBS 2017 DUS 1910-2:2017 Compliance
More informationSupporting CE-Marking Obligations of Our Customers: The Role of the Galvanizer
Supporting CE-Marking Obligations of Our Customers: The Role of the Galvanizer NORDIC GALVANIZERS ANNUAL MEETING 8 MAY 2014 COPENHAGEN MURRAY COOK EXECUTIVE DIRECTOR EUROPEAN GENERAL GALVANIZERS ASSOCIATION
More informationISO INTERNATIONAL STANDARD. Metallic materials Tensile testing Part 2: Method of test at elevated temperature
INTERNATIONAL STANDARD ISO 6892-2 First edition 2011-02-15 Metallic materials Tensile testing Part 2: Method of test at elevated temperature Matériaux métalliques Essai de traction Partie 2: Méthode d'essai
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 3601-2 Second edition 2016-07-15 Fluid power systems O-rings Part 2: Housing dimensions for general applications Transmissions hydrauliques et pneumatiques Joints toriques Partie
More informationINTERNATIONAL STANDARD ISO 4427-2 First edition 2007-08-01 Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 2: Pipes Systèmes de canalisations en plastique Tubes et raccords
More informationISO INTERNATIONAL STANDARD. Hydraulic fluid power On-line automatic particle-counting systems for liquids Methods of calibration and validation
INTERNATIONAL STANDARD ISO 11943 First edition 1999-08-01 Hydraulic fluid power On-line automatic particle-counting systems for liquids Methods of calibration and validation Transmissions hydrauliques
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD First edition 1997-03-01 Welded steel tubes for pressure purposes - Technical delivery conditions - Part 6: Longitudinally steel tubes welded austenitic stainless Tubes soud6.s en
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 21138-2 First edition 2007-10-15 Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride)
More informationSpecification and qualification of welding procedures for metallic materials General rules
BRITISH STANDARD BS EN ISO 15607:2003 Specification and qualification of welding procedures for metallic materials General rules The European Standard EN ISO 15607:2003 has the status of a British Standard
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 16204 First edition 2012-09-01 Durability Service life design of concrete structures Durabilité Conception de la durée de vie des structures en béton Reference number ISO 16204:2012(E)
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 9974-4 Minor Revision Draft 2016-04-12 Connections for general use and fluid power Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing Part 4:
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 15610 First edition 2003-10-01 Specification and qualification of welding procedures for metallic materials Qualification based on tested welding consumables Descriptif et qualification
More informationISO INTERNATIONAL STANDARD. Water quality Determination of sulfates Method by continuous flow analysis (CFA)
INTERNATIONAL STANDARD ISO 22743 First edition 2006-04-15 Water quality Determination of sulfates Method by continuous flow analysis (CFA) Qualité de l'eau Dosage des sulfates Méthode par analyse en flux
More informationISO 1456 INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 1456 Fourth edition 2009-08-01 Metallic and other inorganic coatings Electrodeposited coatings of nickel, nickel plus chromium, copper plus nickel and of copper plus nickel plus
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 683-1 Third edition 2016-07-01 Heat-treatable steels, alloy steels and free-cutting steels Part 1: Non-alloy steels for quenching and tempering Aciers pour traitement thermique,
More informationKowsar San'at Espadana Co.
BRITISH STANDARD BS EN 10240:1998 The European Standard EN 10240 : 1997 has the status of a British Standard ICS 23.040.10; 25.220.40; 77.140.75 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY
More informationLicensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sat Dec 02 09:19:48 GMT+00: , Uncontrolled Copy, (c) BSI This British
BRITISH STANDARD Rigid cellular plastics Determination of tensile properties ICS 83.100 BS ISO 1926:2005 Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sat Dec 02 09:19:48 GMT+00:00
More informationSpecification and approval of welding procedures for metallic materials
BRITISH STANDARD BS EN 288-7:1995 Specification and approval of welding procedures for metallic materials Part 7: Approval by a standard welding procedure for arc welding The European Standard EN 288-7:1995
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 683-2 Second edition 2016-07-01 Heat-treatable steels, alloy steels and free-cutting steels Part 2: Alloy steels for quenching and tempering Aciers pour traitement thermique,
More informationAustralian/New Zealand Standard
AS/NZS 1100.501:2002 AS/NZS 1100.501 Australian/New Zealand Standard Technical drawing Part 501: Structural engineering drawing AS/NZS 1100.501:2002 This Joint Australian/New Zealand Standard was prepared
More informationISO INTERNATIONAL STANDARD. Elastomeric seismic-protection isolators Part 2: Applications for bridges Specifications
INTERNATIONAL STANDARD ISO 22762-2 Second edition 2010-11-01 Elastomeric seismic-protection isolators Part 2: Applications for bridges Specifications Appareils d'appuis structuraux en élastomère pour protection
More informationAWS D8.2M:2017 An American National Standard. Specification for Automotive Weld Quality Resistance Spot Welding of Aluminum
An American National Standard Specification for Automotive Weld Quality Resistance Spot Welding of Aluminum An American National Standard Approved by American National Standards Institute March 9, 2017
More informationWelding Welding of reinforcing steel
BRITISH STANDARD BS EN ISO 17660-2:2006 Welding Welding of reinforcing steel Part 2: Non load-bearing welded joints ICS 25.160.10 National foreword This British Standard is the UK implementation of EN
More informationISO INTERNATIONAL STANDARD. Needle-free injectors for medical use Requirements and test methods
INTERNATIONAL STANDARD ISO 21649 First edition 2006-06-01 Needle-free injectors for medical use Requirements and test methods Injecteurs sans aiguille à usage médical Exigences et méthodes d'essai Reference
More informationAS/NZS ISO 9004:2011 Managing for the sustained success of an organization A quality management approach
AS/NZS ISO 9004:2011 Managing for the sustained success of an organization A quality management approach AS/NZS ISO 9004:2011 This Joint Australian/New Zealand Standard was prepared by Joint Technical
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 16276-1 First edition 2007-05-15 Corrosion protection of steel structures by protective paint systems Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture
More informationISO INTERNATIONAL STANDARD. Steel for the reinforcement and prestressing of concrete Test methods Part 1: Reinforcing bars, wire rod and wire
INTERNATIONAL STANDARD ISO 15630-1 Second edition 2010-10-15 Steel for the reinforcement and prestressing of concrete Test methods Part 1: Reinforcing bars, wire rod and wire Aciers pour l'armature et
More informationIntroduction Introduction
Introduction Maritime International is a leading manufacturer of marine bollards and cleats worldwide. Our range of bollards and cleats is unsurpassed by any other manufacturer or supplier. Maritime can
More informationAustralian/New Zealand Standard
AS/NZS ISO 9001:2008 ISO 9001:2008 (Incorporating Amendment No. 1) AS/NZS ISO 9001:2008 Australian/New Zealand Standard Quality management systems Requirements AS/NZS ISO 9001:2008 This Joint Australian/New
More informationISO INTERNATIONAL STANDARD. Water quality Determination of the chemical oxygen demand index (ST-COD) Small-scale sealed-tube method
INTERNATIONAL STANDARD ISO 15705 First edition 2002-11-15 Water quality Determination of the chemical oxygen demand index (ST-COD) Small-scale sealed-tube method Qualité de l'eau Détermination de l'indice
More informationISO INTERNATIONAL STANDARD. Metallic materials Vickers hardness test Part 3: Calibration of reference blocks
INTERNATIONAL STANDARD ISO 6507-3 Third edition 2005-12-15 Metallic materials Vickers hardness test Part 3: Calibration of reference blocks Matériaux métalliques Essai de dureté Vickers Partie 3: Étalonnage
More informationAustralian Standard. Metal castings. Part 1: Ferrous sand moulded AS (Incorporating Amendment No. 1) AS
AS 4738.1 2004 (Incorporating Amendment No. 1) AS 4738.1 2004 Australian Standard Metal castings Part 1: Ferrous sand moulded This Australian Standard was prepared by Committee MT-001, Iron and Steel.
More informationAWS A5.16/A5.16M:2007 An American National Standard. Specification for Titanium and Titanium-Alloy Welding Electrodes and Rods
An American National Standard Specification for Titanium and Titanium-Alloy Welding Electrodes and Rods An American National Standard Approved by the American National Standards Institute August 17, 2007
More informationIS First edition
INTERNATIONAL STANDARD IS0 7005-2 First edition 1988-12-15 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION ORGANISATION INTERNATIONALE DE NORMALISATION MEXflYHAPOAHAfl OPTAHMA~Mfl I-IO CTAHflAPTMA~MM Metallic
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 19598 First edition 2016-11-15 Metallic coatings Electroplated coatings of zinc and zinc alloys on iron or steel with supplementary Cr(VI)- free treatment Revêtements métalliques
More informationAustralian Standard. Pressure equipment Examination and testing AS Reconfirmed 2016
AS 4037 1999 Reconfirmed 2016 Australian Standard Pressure equipment Examination and testing This Australian Standard was prepared by Committee ME/1, Pressure Equipment. It was approved on behalf of the
More informationISO INTERNATIONAL STANDARD. Plain end steel tubes, welded and seamless - General tables of dimensions and masses per unit length
INTERNATIONAL STANDARD ISO 4200 Fourth edition 1991-02-K - Plain end steel tubes, welded and seamless - General tables of dimensions and masses per unit length Tubes lisses en acier, soudés, et sans soudure
More informationISO INTERNATIONAL STANDARD. Calculation of load capacity of spur and helical gears Part 6: Calculation of service life under variable load
INTERNATIONAL STANDARD ISO 6336-6 First edition 2006-08-15 Calculation of load capacity of spur and helical gears Part 6: Calculation of service life under variable load Calcul de la capacité de charge
More informationPED Certified OHSAS 18001:2007 ISO 9001 : 2008 ISO 14001:2004 Govt. Recog. Export House.
PED Certified OHSAS 18001:2007 ISO 9001 : 2008 ISO 14001:2004 Govt. Recog. Export House. Manufacturer, Exporter, Stockiest, Supplier, Trader for Carbon Steel, Stainless Steel, Alloy Steel for Seamless,
More informationAS/NZS 1477:2017. Australian/New Zealand Standard. PVC pipes and fittings for pressure applications. Superseding AS/NZS 1477:2006 AS/NZS 1477:2017
AS/NZS 1477:2017 Australian/New Zealand Standard PVC pipes and fittings for pressure applications Superseding AS/NZS 1477:2006 AS/NZS 1477:2017 AS/NZS 1477:2017 This joint Australian/New Zealand standard
More informationISO INTERNATIONAL STANDARD. Non-destructive testing of welds Eddy current testing of welds by complex-plane analysis
INTERNATIONAL STANDARD ISO 17643 First edition 2005-07-01 Non-destructive testing of welds Eddy current testing of welds by complex-plane analysis Contrôle non destructif des assemblages soudés Contrôle
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 15613 First edition 2004-06-15 Specification and qualification of welding procedures for metallic materials Qualification based on pre-production welding test Descriptif et qualification
More informationSECTION CHAIN LINK FENCES AND GATES (GALVANIZED) A. Fence framework, fabric, gates, and accessories.
SECTION 02830 CHAIN LINK FENCES AND GATES (GALVANIZED) 1.0 GENERAL 1.1 Section Includes A. Fence framework, fabric, gates, and accessories. B. Excavation for post bases; concrete footing for posts. C.
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 10675-1 First edition 2008-03-01 Non-destructive testing of welds Acceptance levels for radiographic testing Part 1: Steel, nickel, titanium and their alloys Essais non destructifs
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 10406-1 Second edition 2015-01-15 Fibre-reinforced polymer (FRP) reinforcement of concrete Test methods Part 1: FRP bars and grids Polymère renforcé par des fibres (PRF) pour
More informationISO INTERNATIONAL STANDARD. Quality requirements for fusion welding of metallic materials Part 4: Elementary quality requirements
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 3834-4 Second edition 2005-12-15 Quality requirements for fusion welding of metallic materials Part 4: Elementary quality requirements Exigences
More informationISO INTERNATIONAL STANDARD. Fasteners Preloading test for the detection of hydrogen embrittlement Parallel bearing surface method
INTERNATIONAL STANDARD ISO 15330 First edition 1999-09-01 Fasteners Preloading test for the detection of hydrogen embrittlement Parallel bearing surface method Éléments de fixation Essai de précharge pour
More informationThis document is a preview generated by EVS
TECHNICAL REPORT ISO/IEC TR 33014 First edition 2013-12-01 Information technology Process assessment Guide for process improvement Technologies de l'information Évaluation des procédés Guide de l'amélioration
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 7153-1 Third edition 2016-10-01 Surgical instruments Materials Part 1: Metals Instruments chirurgicaux Matériaux Partie 1: Métaux Reference number ISO 7153-1:2016(E) ISO 2016
More informationHot rolled products of structural steels
BRITISH STANDARD Hot rolled products of structural steels Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels The European Standard EN 10025-4:2004 has
More informationISO/IEC INTERNATIONAL STANDARD. Information technology Service management Part 2: Guidance on the application of service management systems
INTERNATIONAL STANDARD ISO/IEC 20000-2 Second edition 2012-02-15 Information technology Service management Part 2: Guidance on the application of service management systems Technologies de l'information
More informationISO INTERNATIONAL STANDARD. Cranes Design calculation for rail wheels and associated trolley track supporting structure Part 1: General
INTERNATIONAL STANDARD ISO 16881-1 First edition 2005-05-15 Cranes Design calculation for rail wheels and associated trolley track supporting structure Part 1: General Appareils de levage à charge suspendue
More informationAustralian Standard. Certification of welders and welding supervisors. AS (Incorporating Amendment No. 1) AS 1796
AS 1796 2001 (Incorporating Amendment No. 1) AS 1796 Australian Standard Certification of welders and welding supervisors This Australian Standard was prepared by Committee ME-001, Pressure Equipment.
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 8502-6 Second edition 2006-07-01 Preparation of steel substrates before application of paints and related products Tests for the assessment of surface cleanliness Part 6: Extraction
More informationPlastics collapsible containers for human blood and blood components. Part 1: Conventional containers
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 3826-1 Second edition 2013-06-01 Plastics collapsible containers for human blood and blood components Part 1: Conventional containers Poches en
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 9626 Second edition 2016-08-01 Stainless steel needle tubing for the manufacture of medical devices Requirements and test methods Tubes d aiguilles en acier inoxydable pour la
More information(Notices) NOTICES FROM EUROPEAN UNION INSTITUTIONS, BODIES, OFFICES AND AGENCIES EUROPEAN COMMISSION
17.11.2017 EN Official Journal of the European Union C 389/1 IV (Notices) NOTICES FROM EUROPEAN UNION INSTITUTIONS, BODIES, OFFICES AND AGENCIES EUROPEAN COMMISSION Commission communication in the framework
More informationAS/NZS :2003. Plumbing and drainage AS/NZS :2003. Australian/New Zealand Standard. Part 3: Stormwater drainage
AS/NZS 3500.3:2003 Incorporating Amendment Nos 1, 2, and 3 Australian/New Zealand Standard Plumbing and drainage Part 3: Stormwater drainage AS/NZS 3500.3:2003 AS/NZS 3500.3:2003 This Joint Australian/New
More informationAS/NZS ISO 9001:2016. Quality management systems Requirements AS/NZS ISO 9001:2016. Australian/New Zealand Standard. Superseding AS/NZS ISO 9001:2008
AS/NZS ISO 9001:2016 (ISO 9001:2015, IDT) Australian/New Zealand Standard Quality management systems Requirements Superseding AS/NZS ISO 9001:2008 AS/NZS ISO 9001:2016 AS/NZS ISO 9001:2016 This joint Australian/New
More informationISO INTERNATIONAL STANDARD. Rubber compounding ingredients Process oils Determination of glass transition temperature by DSC
INTERNATIONAL STANDARD ISO 28343 First edition 2010-09-01 Rubber compounding ingredients Process oils Determination of glass transition temperature by DSC Ingrédients de mélange du caoutchouc Huiles de
More informationGas Transmission and Distribution Piping Systems
ASME B31.8-2014 (Revision of ASME B31.8-2012) Gas Transmission and Distribution Piping Systems ASME Code for Pressure Piping, B31 AN INTERNATIONAL PIPING CODE ASME B31.8-2014 (Revision of ASME B31.8-2012)
More informationWood-based panels Surface soundness Test method
BRITISH STANDARD BS EN 311:2002 Wood-based panels Surface soundness Test method The European Standard EN 311:2002 has the status of a British Standard ICS 79.060.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT
More informationStandards for Welding
NEW CATALOGUE Standards for Welding Specifications, procedures and tests for use by welders, quality controllers and manufacturers Equipping business with knowledge Standards for Welding Specifications,
More informationSurface chemical analysis Analysis of zinc- and/or aluminium-based metallic coatings by glow-discharge optical-emission spectrometry
INTERNATIONAL STANDARD ISO 16962 Second edition 2017-02 Surface chemical analysis Analysis of zinc- and/or aluminium-based metallic coatings by glow-discharge optical-emission spectrometry Analyse chimique
More informationNon-destructive testing of welds
BRITISH STANDARD BS EN 12517-1:2006 Non-destructive testing of welds Part 1: Evaluation of welded joints in steel, nickel, titanium and their alloys by radiography Acceptance levels The European Standard
More informationMarcegaglia do Brasil
Garuva plant Marcegaglia do Brasil 7 millions wire on tube condensers 240 millions meters of welded tubes for refrigeration 180.000 tons of electro-welded carbon tubes Brasília 20.000 tons of stainless
More informationISO INTERNATIONAL STANDARD. Plastics Determination of Charpy impact properties Part 1: Non-instrumented impact test
INTERNATIONAL STANDARD ISO 179-1 Second edition 2010-06-15 Plastics Determination of Charpy impact properties Part 1: Non-instrumented impact test Plastiques Détermination des caractéristiques au choc
More informationISO INTERNATIONAL STANDARD. Safety devices for protection against excessive pressure Part 2: Bursting disc safety devices
INTERNATIONAL STANDARD ISO 4126-2 First edition 2003-01-15 Safety devices for protection against excessive pressure Part 2: Bursting disc safety devices Dispositifs de sécurité pour protection contre les
More informationMarley Air Cooled Heat Exchangers
Marley Air Cooled Heat Exchangers SPX: The Informed Choice for the Demands of Today and Tomorrow SPX Cooling Technologies has the experience, engineering expertise and in-factory manufacturing capabilities
More information