SECTION EPOXY TERRAZZO TILE WITH RECYCLED GLASS MATRIX

Transcription

1 GlassPLANK GUIDE SPECIFICATION Manufacturer: GLASS RECYCLED LLC 2939 Irving Blvd Suite 305 Dallas TX (888) toll free voice SECTION EPOXY TERRAZZO TILE WITH RECYCLED GLASS MATRIX This guide specification has been prepared by GLASS RECYCLED LLC., in printed and electronic media, as an aid to specifiers in preparing written construction documents for GlassPLANK tile using GlassSCAPE recycled glass and/or recycled porcelain epoxy matrix. GlassPLANK represents 80 percent recycled glass and /or recycled porcelain matrix and 20 percent VOC-free color-pigmented epoxy resin binder). It is imperative, when specifying non-breathing floor coverings such as epoxy terrazzo tile and monolithic epoxy terrazzo that the substrate to which the flooring is adhered is within manufacturer's recommended tolerances for moisture content and ph level. New concrete slabs should have a water/cement ratio of not more than 0.45 in conjunction with an upgraded vapor retarder properly installed directly beneath the concrete slab. Both existing and new slabs should be tested for moisture and ph using a calcium crystal kit at not less than 500 sqft increments. Elevated moisture or ph must be mitigated before new floor coverings can be installed. Refer to NTMA recommendations for further information regarding acceptable moisture and ph levels Edit entire master to suit project requirements. Modify or add items as necessary. Delete items which are not applicable. Words and sentences within brackets [ ] reflect a choice to be made regarding inclusion or exclusion of a particular item or statement. This section may include performance, proprietary and descriptive type specifications. Edit to avoid conflicting requirements. Editor notes to guide the specifier are included between lines of asterisks to assist in choices to be made. Remove these notes before final printing of specification. This guide specification is written around the Construction Specifications Institute (CSI), Section Format standards references to section names and numbers are based on MasterFormat For specification assistance on specific product applications, please contact our offices above or any of our local product representatives throughout the country. GLASS RECYCLED LLC reserves the right to modify these guide specifications at any time. Updates to this guide specification will be posted to the manufacturer s web site and/or in printed matter as they occur. GLASS RECYCLED LLC makes no expressed or implied warranties regarding content, errors, or omissions in the information presented. GLASS RECYCLED LLC Guide Specification

2 PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Fabrication and installation of GlassPLANK epoxy terrazzo tile with recycled glass matrix. 2. Accessories necessary to complete work. * Edit the "Related Sections" paragraph to identify other sections that may relate to work of this section. B. Related Sections: 1. [Section LEED Requirements: Additional LEED requirements.] 2. [Section Quality Requirements: Mock-ups.] 3. [Section Tiling: Other thin-set tile applications.] 1.2 SUBMITTALS A. General: Submit in accordance with Section B. [LEED Submittals: 1. Credit MR 4.1[and 4.2]: Product Data indicating percentages by weight of post consumer and post industrial recycled content for products having recycled content. a. Include statement indicating costs for each product having recycled content. 2. Credit MR 5.1[and 5.2]: Certification of content complying with Regionally Manufactured or Regionally Extracted Materials. 3. Credit EQ 4.1: Manufacturers' product data for adhesives and sealants, including printed statement of VOC content.] C. Shop Drawings: 1. Indicate tile layout, patterns, color arrangement, perimeter conditions, and junctions with dissimilar materials, thresholds, and setting details. 2. Locate and detail expansion and control joints. D. Samples: Submit following: 1. Submit full range of available colors for selection purposes for Architect s selection. After initial selection, submit a maximum of two (2) samples, minimum 3 x 3 for each finished combination of Epoxy Resin Color and Glass Aggregate Color for acceptance before proceeding with Work. 1.3 QUALITY ASSURANCE A. Fabricator Qualifications: Company specializing in fabricating work specified in this Section with minimum five years experience in type work required for Project. B. Materials Supplier: 1. Materials furnished shall meet GLASS RECYCLED LLC Specifications. 2. Epoxy Resin supplier must be an Authorized Vendor of GLASS RECYCLED LLC * On larger project, consider specifying a mock-up of one portion of the work for approval of installed unit. 1.4 [MOCK-UPS A. General: Comply with Section B. Construct mock-up of each type of tile installation for Architect s approval. Completed mock-up [may] [may not] remain as completed work.] 1.5 DELIVERY, STORAGE, AND HANDLING GLASS RECYCLED LLC Guide Specification

3 A. Comply with Section Handle, transport, and store units to prevent damage to materials or structure. Handle with care to prevent damage to corners and scratches to faces. 2. Broken, cracked, chipped, stained or damaged product will be rejected. 1.6 WARRANTY A. Warranty shall apply to manufactures written policy for a period of 1 year from delivery of shipment. GLASS RECYCLED LLC recycled glass and porcelain products are by design, hand crafted product. Certain imperfections and surface characteristics are inherent and part of the products final composition. PART 2 - PRODUCTS 2.1 ACCEPTABLE FABRICATORS A. Subject to compliance with requirements indicated, provide products from fabricators listed below: 1. GLASS RECYCLED LLC, 2939 Irving Blvd Suite 305 Dallas TX 75247, (888) ) 2. Substitutions: Submit in accordance with Section MATERIAL A. GLASS RECYCLED LLC Epoxy Terrazzo with Glass Matrix: Provide sound, hard, durable, epoxy terrazzo of uniform strength, color, and texture. 1. Epoxy Resin Performance Criteria without GlassSCAPE aggregate added: PROPERTY TEST METHOD REQUIREMENT Hardness ASTM D-2240 using Shore D Durometer Tensile Strength ASTM D minimum Compressive Strength ASTM D-695 Specimen B Cylinder Chemical Resistance ASTM D-1308/ 7 days at room temperature by immersion method have no deleterious effects. > 75 3,000 psi minimum 10,000 psi minimum No effect a. Epoxy Resin color: [ ] [As selected by [Architect] from Manufacturer s full available range]. B. Aggregate: % Post Recycled Glass and/or Porcelain Aggregate. 2. GlassSCAPE Aggregate: As supplied by GLASS RECYCLED LLC. 3. Sizes to conform to NTMA Gradation standards. 4. Aggregate color: [ ] [As selected by [Architect] from Manufacturer s full available range]. C. GlassPLANK : Provide sound, hard, durable, epoxy terrazzo tiles of uniform strength, color, and texture. 1. Epoxy Resin blended with three volumes of GlassSCAPE glass finished to nominal 1/4 thickness, per Manufacturer s recommendations: 2. Performance criteria with GLASS RECYCLED LLC aggregate: PROPERTY TEST METHOD REQUIREMENT GLASS RECYCLED LLC Guide Specification

4 Flammability ASTM D-635 Self-extinguishing, extent of burning 0.25 maximum Thermal Coefficient of Linear ASTM D x 10-6 per 140 degrees Expansion Fahrenheit. Bond Strength Surface Soundness 100% Concrete failure minimum Adhesion Test 300 PSI minimum tensile strength 3. Acceptable Product: GLASS RECYCLED LLC; GlassPLANK. 4. Tile Characteristics: a. Dimensions: Varies Sizes Available. Maximum Floor Tile Size; 24 x36 b. Thickness: ¼,3/8, ½ or 5/8 c. Profile: Squared edge. d. Panels: Shall conform to shop drawings with a maximum 1/8 tolerance in dimension. e. Surface: Polished with overall uniformity in color matrix and aggregate; shall meet ADA Non-slip Coefficient 0.5 or higher rating. D. Mortars and Grouts: Non-staining, type as recommended by manufacturer: 1. Acceptable Manufacturer: Mapei, Inc. a. Mortar: Mapei, Inc.; UltraFlex 3 or approved equal. b. Grout: Mapei, Inc.; color-matched non-sanded or approved equal. 1) Color: As selected by Architect from Manufacturer s full available range. PART 3 - EXECUTION 3.1 EXAMINATION A. Examine conditions and proceed with work in accordance with Section B. Confirm that supporting construction is complete, and is level, square, true, rigid, and secure. C. Moisture Vapor Transmission Test: ASTM E1907. Perform by independent testing laboratory to determine suitability of concrete sub floor for receiving resilient flooring with regard to moisture content and curing compounds. Ensure concrete is within floor manufacturer s recommended limits prior to installation. 1. Section includes one possible solution to excessive moisture vapor transmission. 2. ASTM E1907 Qualitative Anhydrous Calcium Chloride Test: For substrates with moisture vapor permeance in excess of 1.36 kg water vapor per 93 square meters [(3 pounds water vapor per 1000 square feet)] per 24 hour period, use floor coating manufacturer s suggested remedy. Do not proceed with flooring application until condition is corrected. D. Perform ph and adhesion tests to concrete substrate in accordance with floor manufacturer s recommendations. Ensure concrete is within NTMA and manufacturer recommended limits prior to terrazzo installation. Submit report to Architect. 3.2 INSTALLATION A. Set GlassPLANK as shown on approved shop drawings. Butt joints uniformly at 1/32. B. Install at locations indicated level, square, true, rigid and secure, and in strict accordance with fabricator s printed instructions. C. Dimensions shall not vary more than 1/8 in length, height, or width. D. Fill joints with approved Grout. E. Thin Set Method, Floors and Walls GLASS RECYCLED LLC Guide Specification

5 1. Apply mortar or adhesive with notched trowel using scraping motion to work material into good contact with surface to be covered. Maintain 90 percent coverage on back of tile and fully bed corners. 2. Apply only as much mortar or adhesive as can be covered within allowable windows as recommended by mortar or adhesive manufacturer or while surface is still tacky. 3. When installing large tiles, ceramics or mosaics, trowel small quantity of mortar or adhesive onto back of each tile or sheet of tiles. 4. Set tiles in place and rub or beat with small beating block. 5. Beat or rap tile to ensure proper bond and also to level surface of tile. 6. Align tile to show uniform joints and allow setting until firm. 7. Clean excess mortar or adhesive from surface of tile with wet cheese cloth (not a sponge) while mortar is fresh. 8. Allow face mounted tile to set until firm before removing paper and before grouting. 9. Sound tile after setting. Replace hollow sounding tiles. 10. Chemical seal is not recommended. 3.3 CLEANING A. General: Comply with Section Keep installed work clean as work progresses. 2. Leave clean and free from blemishes. 3. Clean by moderate use of neutral cleaner acceptable by fabricator. 4. Clean and repair surfaces soiled or otherwise damaged in connection with work of this Section. Pay cost of replacing materials that cannot be satisfactorily cleaned or which have been damaged by improper cleaning materials and techniques. 5. Daily damp mop cleaning recommended. Yearly waxing is optional. 3.4 PROTECTION A. General Contractor shall protect the finished work from the time the Tile Contractor finishes work. END OF SECTION GLASS RECYCLED LLC Guide Specification