LAKEVIEW CEMETERY. Irritech 100% CONSTRUCTION DOCUMENTS - SEPTEMBER 30, 2013 SCHEDULE OF DRAWINGS CLIENT: PROJECT SITE: Not to Scale

Transcription

1 Irritech CLIENT: Irritech VICINITY MAP: Not to Scale TOWN WINDSOR, COLORADO Parks, Recreation & Culture 301 Walnut Street Contact: Wade Willis, Parks and Open Space Manager Tel: Fax: DESIGNER Irritech Design Group 1217 Miramont Drive Fort Collins, CO Contact: Brent C. Jeffery, CID, CLIA, Partner Tel % CONSTRUCTION DOCUMENTS - SEPTEMBER 30, 2013 SCHEDULE DRAWINGS IR001 IR100 IR101 IR102 IR103 IR104 IR105 IR501 IR502 IR503 COVER LEGEND AND NOTES PLAN PLAN PLAN PLAN PLAN DETAILS DETAILS DETAILS PROJECT SITE PROJECT SITE: Not to Scale TITLE PROJECT TITLE BY APPR. BJ 09/30/13 NUMBER BJ,RB RB COVER IR

2 SYMBOL MANUFACTURER/MODEL QTY PSI Rain Bird 1804-SAM-PRS-NP 5 Series MPR 2 30 Rain Bird 1804-SAM-PRS-NP 15 Series MPR Rain Bird 1806-PRS-NP 15 Series MPR SYMBOL MANUFACTURER/MODEL QTY PSI GPM RADIUS Rain Bird 5006-PL-PC, FC-R-NP-SS-LA ' Rain Bird 5006-PL-PC, FC-R-NP-SS-LA ' Rain Bird 5505-NP (2) ' Rain Bird 5505-NP (2) ' Rain Bird 8005-SS-NP ' Rain Bird 8005-SS-NP ' Rain Bird 8005-SS-NP ' Rain Bird 8005-SS-NP ' Rain Bird 8005-SS-NP ' Rain Bird 8005-SS-NP ' Rain Bird 5006-PC, FC-NP-LA ' Rain Bird 5006-PC, FC-NP-LA ' Rain Bird 5006-PC, FC-NP-LA ' SYMBOL MANUFACTURER/MODEL/DESCRIPTION QTY Valve Callout Remote Control Valve: Rain Bird PESBR-PRS-D-NP 60 1", 1-1/, and Durable Chlorine-Resistant Valves for Reclaimed Water Applications. With Scrubber Mechanism Technology, Purple Flow Control Handle, and Pressure Regulator Module. Decoder unit: Rain Master TW-D-1 (Valves located within 10 feet of one another to share two station decoder TW-D-2) Remote Control Valve: Rain Bird 300-BPES-PRS-D-NP-HAN Globe 3" Brass Electric Remote Control Valve, with Globe Configuration, Purple Handle for Non-Potable Use, and Pressure Regulator Module. Decoder unit: Rain Master TW-D-1 (Valves located within 10 feet of one another to share two station decoder TW-D-2) Quick Coupler Valve: Rain Bird 44-NP 30 1" Brass Quick-Coupling Valve, with Corrosion-Resistant Stainless Steel Spring, Locking Non-Potable Purple Rubber Cover, and 2-Piece Body. Gate Valve: Matco-Norca 10RT 21 to 8" cast iron gate isolation valve. Ring-Tite Gasket Ends. Resilient wedge with epoxy coating and optional nut. Same size as mainline pipe where located. For IPS pipe. Same size as mainline pipe. Flow Sensor: Rain Bird FS-350-B 2 3" and Higher Flow Sensor. BrassModel. Irrigation Lateral Line: PVC Class 200 SDR 21 PVC Class 200 irrigation pipe. Only lateral transition pipe sizes 1 1/4" and above are indicated on the plan, with all others being 1" in size. Pipe Sleeve: PVC Class 200 Typical pipe sleeve for irrigation pipe. Extend sleeves 18 inches beyond edges of paving or construction. Mainline Pipe: PVC Class 200 SDR 21. Size as noted on plans. Minimum size 2 inch Irrigation Controller: Rain Master Eagle-Plus Model EGP-TW. 200 station, wall mount steel enclosure. Two-Wire Communication Cable: TW-CAB-14, With TW-LA-1 Lightening arrestor every 600 feet along wire path. x 1. THE CONTRACTOR SHALL BECOME THOROUGHLY FAMILIAR WITH THE SPECIFICATIONS FOR THIS AND RELATED WORK PRIOR TO CONSTRUCTION. 2. SPRINKLER SYSTEM DESIGN IS BASED ON MINIMUM OPERATING PRESSURE AND MAXIMUM FLOW DEMAND SHOWN ON DRAWINGS AT EACH POINT--CONNECTION. VERIFY WATER PRESSURE PRIOR TO CONSTRUCTION. REPORT DIFFERENCES BETWEEN WATER PRESSURE INDICATED ON DRAWINGS AND ACTUAL PRESSURE READING AT POINT--CONNECTION TO OWNER'S AUTHORIZED REPRESENTATIVE. IN THE EVENT PRESSURE DIFFERENCES ARE NOT REPORTED PRIOR TO START CONSTRUCTION, CONTRACTOR ASSUMES RESPONSIBILITY FOR REVISIONS VOLT ELECTRICAL POWER OUTLET AT THE CONTROLLER WILL BE PROVIDED BY GENERAL CONTRACTOR. MAKE FINAL HOOK-UP FROM ELECTRICAL OUTLET TO AUTOMATIC CONTROLLER. ALL WORK TO BE COMPLETED IN ACCORDANCE WITH CURRENT N.E.C. 4. THIS DESIGN IS DIAGRAMMATIC. PIPING, VALVES, ETC. MAY BE SHOWN WITHIN PAVED AREAS FOR DESIGN CLARIFICATION ONLY AND SHALL BE INSTALLED IN PLANTING AREAS WHERE POSSIBLE. AVOID CONFLICTS BETWEEN SPRINKLER SYSTEM, PLANTING AND ARCHITECTURAL FEATURES. 5. NO VALVE BOXES SHALL BE PLACED WITHIN PLAYFIELD AREAS. EXACT CLEAR DISTANCE REQUIRED FROM ACTIVE AREAS SHALL BE VERIFIED PRIOR TO CONSTRUCTION. DO NOT PLACE VALVE BOXES IN LOW AREAS. 6. DO NOT WILLFULLY INSTALL SPRINKLER SYSTEM AS INDICATED ON DRAWINGS WHEN IT IS OBVIOUS IN FIELD THAT OBSTRUCTIONS, GRADE DIFFERENCES OR AREA DIMENSIONS EXIST THAT MIGHT NOT HAVE BEEN CONSIDERED DURING DESIGN. BRING SUCH OBSTRUCTIONS OR DIFFERENCES TO THE ATTENTION OWNER'S AUTHORIZED REPRESENTATIVE. IN EVENT THIS NOTIFICATION IS NOT PERFORMED, CONTRACTOR ASSUMES RESPONSIBILITY FOR REVISIONS. 7. INSTALL PIPE MATERIALS AND EQUIPMENT AS SHOWN IN DETAILS. USE TEFLON TAPE ON PVC MALE PIPE THREADS AND ON SPRINKLER SWING JOINT AND VALVE ASSEMBLIES. 8. IT IS THE CONTRACTOR'S RESPONSIBILITY TO BECOME FAMILIAR WITH GRADE DIFFERENCES, AND LOCATION WALLS, RETAINING WALLS, ETC. COORDINATE WORK WITH GENERAL CONTRACTOR AND OTHER SUB-CONTRACTORS FOR LOCATION AND INSTALLATION PIPE SLEEVES THROUGH WALLS, UNDER ROADWAYS, PAVING, STRUCTURES, ETC. 8. IN ADDITION TO SLEEVES SHOWN ON THE DRAWINGS, CONTRACTOR IS RESPONSIBLE FOR THE INSTALLATION PIPE SLEEVING AND SEPARATE CONTROL WIRE SLEEVES SUFFICIENT SIZE AT ALL PAVED AREA CROSSINGS. 9. THE FOLLOWING SHOULD BE NOTED REGARDING PIPE SIZING: IF A SECTION UNSIZED LATERAL IS LOCATED BETWEEN TWO IDENTICALLY SIZED SECTIONS THE UNSIZED SECTION SHALL BE THE SAME SIZE. IN NO CASE SHALL A SECTION PIPE BE SMALLER THAN ANY DOWNSTREAM SECTION LOCATED ON THE SAME LATERAL RUN. 10. THE CONTRACTOR SHALL TURN OVER TO THE OWNER; TWO EACH ALL OPERATING KEYS AND SERVICING TOOLS NEEDED FOR COMPLETE ACCESS, ADJUSTMENT, AND REPAIR ALL SYSTEM COMPONENTS. THIS INCLUDES SPECIALIZED TOOLS REQUIRED FOR COMPLETE DISASSEMBLY EACH SPRINKLER AND VALVE. 1. INSTALL POP-UP TYPE SPRINKLER HEADS INSTALLED IN PLANTING AREAS SO THAT TOP SPRINKLER HEAD IS AT LEAST 1 4 " LOWER THAN ADJACENT SIDEWALK OR CURB. 2. SET SPRINKLER HEADS FLUSH WITH AND PERPENDICULAR TO FINISH GRADE AREA TO BE IRRIGATED UNLESS OTHERWISE INDICATED ON DRAWINGS. 3. WHEN VERTICAL OBSTRUCTIONS (FIRE HYDRANTS, TREES, LIGHTS, ETC.) INTERFERE WITH SPRAY PATTERN SPRINKLER HEADS SO AS TO PREVENT PROPER COVERAGE, ADJUST SPRINKLER SYSTEM BY INSTALLING A SPRINKLER HEAD ON EACH SIDE OBSTRUCTION AND ADJUST ARC SO AS TO PROVIDE PROPER COVERAGE. PERFORM ADJUSTMENTS AT NO COST TO OWNERS AUTHORIZED REPRESENTATIVE. 4. FLUSH AND ADJUST SPRINKLERS FOR OPTIMUM PERFORMANCE AND TO PREVENT OVER-SPRAY ONTO WALKS, ROADWAYS, AND BUILDINGS. THIS INCLUDES SELECTING THE BEST DEGREE ARC TO FIT SITE CONDITIONS AND TO THROTTLE FLOW CONTROL AT EACH VALVE TO OBTAIN OPTIMUM PRESSURE FOR EACH SYSTEM. DO NOT ADJUST ROTOR HEADS TO LESS THAN MAXIMUM THROW UNLESS SUCH ADJUSTMENT IS NEEDED TO AVOID OVERSPRAY ONTO BUILDINGS OR HARDSCAPE. 5. INSTALL SPRINKLERS AS SHOWN ON DETAILS. USE TEFLON TAPE ON PVC MALE PIPE THREADS. 6. USE PRESSURE REGULATING SPRINKLER BODIES (PRSs) WHERE MP1000 NOZZLES MUST BE ADJUSTED TO MINIMUM RADII. 7. REMOTE CONTROL VALVES LOCATED WITHIN 10-FEET ONE ANOTHER MUST SHARE A SINGLE TWO-STATION VALVE DECODER UNIT. TERMINATE MAINLINE, WITH QUICK COUPLER VALVE, FOR FUTURE EXTENSION. TERMINATE CONTROL WIRE WITH A 36" LONG COIL WITH 3M-BDY CONNECTOR. LOCATE IN IN A 10-INCH ROUND BOX PLACED DIRECTLY OVER PIPE LOCATION. TEMPORARY TO BE FIELD ADJUSTED PER STREETSCAPE PLANTING IMPROVEMENTS AND EXISTING SITE FEATURES. COORDINATE ALL ADJUSTMENTS WITH CITY REPRESENTATIVE. CONNECT NEW MAINLINE TO EXISTING MAINLINE SERVING BALL FIELD. FIELD VERIFY EXACT LOCATION EXISTING MAINLINE. ROUTE NEW CONTROL WIRE AND INSTALL DECODER UNITS AT EXISTING VALVES. INSTALL INSERT TYPE FLOW SENSOR IN 4" MAINLINE. PROVIDE UNOBSTRUCTED STRAIGHT PIPE SECTIONS 40" UPSTREAM AND 2'" DOWNSTREAM FROM SENSOR. EXTEND DEDICATED (JACKETED, DIRECT BURIAL) WIRE PAIR FROM FLOW SENSOR TO CONTROLLER LOCATION. FOLLOW ALL MANUFACTURERS RECCOMENDATIONS. INSTALL CONTROLLERS PER DETAILS, IN APPROXIMATE LOCATION SHOWN. CONNECT TO 120V POWER, COORDINATE POWER CONNECTION WITH OTHER TRADES. FOLLOW ALL APPLICABLE ELECTRICAL CODES. FINAL LOCATION TO BE APPROVED BY OWNERS REP. PRIOR TO INSTALLATION. FUTURE ZONE TO BE INSTALLED WITH NEW WALKWAY IMPROVEMENTS. INSTALL REMOTE CONTROL VALVE AND EXTEND AND CAP LATERAL PIPE 36 INCHES FROM VALVE BOX. FUTURE PART CIRCLE HEADS. INSTALL IN LOCATION SHOWN AND ADJUST TO FULL CIRCLE OPERATION AS TEMPORARY MEASURE UNTIL NEW WALKWAY IMPROVEMENTS ARE INSTALLED. TITLE PROJECT TITLE BY APPR. LEGEND & NOTES #" # # Valve Number Valve Flow Valve Size IR100

3 A18 Irritech A76 1" 15.7 A A A21 A A23 A24 A25 A A27 A20 A19 A A1 A2 A3 A A DG: 4703SF A A12 3" 98.2 A A A A A13 1" 9.74 A9 1" 12.2 TITLE PROJECT TITLE BY APPR. PLAN IR101 A28

4 A74 A A A A A A A A55 1" 15.7 A56 A A A A A A A A A A A A TITLE PROJECT TITLE BY APPR. PLAN IR102

5 A47 A A A A A A A A70 A A72 1" 16.2 A A40 A TITLE PROJECT TITLE BY APPR. PLAN IR103

6 A A A A28 A A37 3" 98.2 A A A30 1" 24.4 A A " A A A81 TITLE PROJECT TITLE BY APPR. PLAN 76.3 IR104

7 A Irritech A A79 A TITLE PROJECT TITLE BY APPR. PLAN IR105

8 A B C D E F TITLE PROJECT TITLE BY APPR. DETAILS IR501

9 A B C D E F TITLE PROJECT TITLE BY APPR. DETAILS IR502

10 A B TITLE PROJECT TITLE BY APPR. DETAILS IR503