4.10. Registration For The Practical Training Pre-requisite Requirement For Registration Overlapping/Equivalent Courses...

Transcription

1 1 P a g e

2 Contents 2 Academic and Examination System Introduction... 6 Academic Structure:... 6 (a) Academic Programmes:... 6 (b) Student s Unique ID (UID): Course Structure and Credit System... 6 Course Numbering Scheme... 6 (a) Codes For The Nature Of The Course: The nature of the course corresponding to the third alphabet in the course code is given in Table-1:... 6 Table 1: Codes For The Nature Of Courses... 7 (b) Level of the Course: The first digit of the numeric part of the course code indicates level of the course as determined by pre-requisite course and/or by the maturity required for registering for the course. The latter requirement is enforced through a requirement of minimum number of earned credits. In general, 7 (c) Numbering Scheme For Courses Of Special Nature: The numbering scheme for courses of special nature is given below. Here xx is the Academic unit code, and y is the digit from the programme code. 7 Table 2: Numbering Scheme For Courses Of Special Nature... 7 Credit System:... 8 Course Credits Assignment:... 8 Earning Credits:... 8 Course Content Description... 8 Pre-requisites... 9 Course Coordinator... 9 Grading System... 9 Table 3 : Grade Points... 9 Description of grades Evaluation of Performance Table 4: Typical Academic performance calculation-i Semester Table 5: Typical Academic Performance Calculations - II Semester REGISTRATION AND ATTENDANCE Registration Registration And Student Status Advice On Courses Registration Validation Minimum Student Registration In A Course Late Registration Addition, Deletion, Audit And Withdrawal From Courses (From 3rd Semester Onwards) Semester Withdrawal Registration In Special Module Courses P a g e

3 4.10. Registration For The Practical Training Pre-requisite Requirement For Registration Overlapping/Equivalent Courses Limits on Registration Registration and Fees Payment Registration Record Continuous Absence And Registration Status Attendance Rule Absence During The Semester Change Of Department Branch/Program At The End Of First Year: Branch Change Rules for Program Change UNDERGRADUATE DEGREE REQUIREMENTS, REGULATIONS AND PROCEDURES Overall Requirements B.Tech Dual Degree Programmes (Major + Minor) Integrated M.Tech Degree Requirements Breakup Earned Credits Degree Grade Point Average (DGPA) Requirement Practical Training NCC/NSS/NSO Break-Up Of Earned Credits Audit Courses Lower And Upper Limits For Credits Registered Conditions For Termination Of Registration, Probation And Warning Slow-Paced Programme Maximum Duration For Completing Degree Requirements Courses Of Special Nature a) N.C.C., N.S.O. and N.S.S b) Independent Study c) Mini Project d) Practical Training e) Colloquium f) B. Tech Project g) Major Project (Integrated M.Tech, 2yr M.Tech) Open Category Open Category Credits Minor Area P a g e

4 6.3 Self-study Course Summer Semester POSTGRADUATE DEGREE REQUIREMENTS, REGULATIONS AND PROCEDURES M.Tech (Full Time/ Part Time) DURATION FOR THE PROGRAMME ELIGIBILITY FOR ADMISSIONS M. TECH. (FULL-TIME & PART-TIME) PROGRAMME ACADEMIC PERFORMANCE REQUIREMENTS EXAMINATION SCHEME THESIS EXAMINATION M TECH THESIS ORAL EXAMINATION COMMITTEE M. TECH. THESIS M TECH. ORAL EXAMINATION M.Tech Degree Requirements Continuation Requirements Lower And Upper Limits For Credits Registered Audit Requirement Summer Registration The overall credits structure: B.Tech. [Civil] The overall credits structure: B.Tech. [CSE] The overall credits structure: B.Tech. [EE] The overall credits structure: B.Tech. [ECE] The overall credits structure: B.Tech. [Mechanical] The overall credits structure: B.Tech.+ M.Tech. [Civil] The overall credits structure: B.Tech.+ M.Tech. [CSE] The overall credits structure: B.Tech. + M.Tech. [EE] The overall credits structure: B.Tech.+ M.Tech. [ECE] The overall credits structure: B.Tech.+ M.Tech. [Mechanical] The overall credits structure: B.Tech. + MBA [Civil] The overall credits structure: B.Tech.+ MBA [CSE] The overall credits structure B.Tech.+MBA [EE] The overall credits structure: B.Tech.+MBA [ECE] The overall credits structure: B.Tech.+MBA [ME] The overall credits structure: M. Tech. [Part Time] The overall credits structure: M.Tech. [Full Time] The overall credits structure: Polytechnic [Civil] The overall credits structure: Polytechnic [EE] The overall credits structure: Polytechnic [ECE] The overall credits structure: Polytechnic [ME] P a g e

5 30 The overall credits structure BCA+MCA BCA+MCA [Proposed Scheme] The overall credits structure BCA BCA [Proposed Scheme] The overall credits structure MCA MCA [Proposed Scheme] The overall credits structure MBA The overall credits structure BBA The overall credits structure B.Com The overall credits structure: Department Elective BBA The overall credits structure: BBA+ MBA The overall credits structure: B.Com. + MBA The overall credits structure: Department Elective BBA+MBA and B.Com+MBA Course Overview (Civil) B.Tech, B.Tech+M.Tech, B.Tech.+ MBA Department of B.Tech, B.Tech + M.Tech Computer Science Department of B.Tech, B.Tech + M.Tech Electrical Department of B.Tech, B.Tech + M.Tech Mechanical Department of Physics MAL-120 MATHEMATICS-II MAL101 BUSINESS MATHEMATICS Department of Chemistry SYLLABUS ENGLISH (All Semester) Polytechnic Department of Civil Polytechnic Department of Computer Science Department Computer Applications Department of Electrical Polytechnic Polytechnic Electronics Department Polytechnic Mechanical Department Department of Management P a g e

6 1 Academic and Examination System 2.1 Introduction Career Point University, Kota provides education with a view to produce quality technocrats managers, professional and scientists. The curriculum provides broad based knowledge and simultaneously builds a temper for the life long process of learning and exploring. At the undergraduate level, a student needs to do compulsory foundation courses in the areas of selected disciplineapart from departmental requirements. Departmental courses (core and electives) constitute 50% of the total curriculum. Further, students opt to study open category electives to develop broad inter-disciplinary knowledge base or to specialize significantly in an area outside their core discipline. At the postgraduate level, students are encouraged to look beyond their area of specialization to broaden their horizons through open electives. The medium of instruction in the University is English. The University follows the Credit Based Semester System for all courses except Polytechnic Diploma, B.Sc., M.Sc., B.A. and M.A. where university is following Yearly Scheme. The academic year runs from July through June each year and comprises of two regular semesters and one special summer semester. Typically, the first semester (odd semester) starts in July and ends in December. The second semester (even semester) starts in January and ends in May. Summer semester starts from June and ends in July. Detailed scheduledfor the Semester is given before the commencement of every new semester. Academic Structure: The major academic units of the University are its various Schools and Departments. The activities of departments include teaching and research at all levels. (a) Academic Programmes: Career Point University, Kota, Rajasthan offers a variety of academic programmes in various disciplines for students with a wide range of backgrounds. Admission to many of these programmes are based on performance in national / University level entrance tests/ other entrance examinations followed by interviews in some cases. The courses offered by Career Point University are presently classified into Certificate, Diploma, Undergraduate, Postgraduate and Research programmes. This classification is based primarily on entry/admission qualification of students rather than the level of degree offered. For all undergraduate programmes, students are admitted after 10+2 schooling while for all postgraduate programmes, students are admitted after they have obtained at least a college level Bachelor s degree. In certificate and diploma programs the entry level qualification may vary from program to program. (b) Student s Unique ID (UID): Each admitted student is given unique identification number (UID). This UID will remain the same during the entire tenure of the student with university. eg. K For any communication, students must mention their UID. 2 Course Structure and Credit System Course Numbering Scheme Normally every course at Career Point University runs for the full length of the semester. At the beginning of the semester, the students register for courses that they want to study and at the end of the semester a grade is awarded. On obtaining a pass grade, the student earns all the credits associated with the course. A fail grade does not get any credit. Partial credits are also not awarded. Each course number is denoted by six alpha-numerals, three alphabets are followed by three numerals: E E L Code of the Academic Unit offering the Course Nature of the Course Unique Identification code for the Course Level of the Course as determined by pre-requisite or number of the earned credits (a) Codes For The Nature Of The Course: The nature of the course corresponding to the third alphabet in the course code is given in Table-1: 6 P a g e

7 Table 1: Codes For The Nature Of Courses Code L P D T C R N S V Description Lecture courses (other than Lecture hours, these courses may have Tutorial and Practical hours, e.g. L-T-P structures , , 3-0-2, 2-0-0, etc.) Laboratory based courses (Where performance is evaluated primarily on the basis of practical or laboratory work with LTP structures like 0-0-3, 0-0-4, 1-0-3, 0-1-3, etc.) Project based courses leading to dissertation (e.g. Major, Minor, Mini Projects) Training Colloquium Professional Practice Introduction to the Programme or to Humanities and Social Sciences, etc. Independent Study Special Topics Lecture Courses (1 or 2 credits) (b) Level of the Course: The first digit of the numeric part of the course code indicates level of the course as determined by pre-requisite course and/or by the maturity required for registering for the course. The latter requirement is enforced through a requirement of minimum number of earned credits. In general, level courses : Core and elective courses for UG programmes. Usually these courses are not open to any PG student. 500 level courses : Courses for M.Sc. programmes. Usually these courses are not open to other PG students. 600 level courses : Preparatory/introductory courses for M.Tech. programmes These courses are normally not open for UG Students level courses : Core and elective courses for M.Tech.,M.Des., M.B.A., M.S. (Research)and Ph.D. programmes. Usually 800 level courses are advanced courses for PG students (c) Numbering Scheme For Courses Of Special Nature: The numbering scheme for courses of special nature is given below. Here xx is the Academic unit code, and y is the digit from the programme code. Table 2: Numbering Scheme For Courses Of Special Nature Course description Introduction to the Programme Independent Study Professional Practices Practical Training Colloquium Mini Project B.Tech. Major Project Part 1 B.Tech. Major Project Part 2 Minor Project (Dual Degree) M.Tech. Major Project Part 1 M.Tech. Major Project Part 1 (Alternative) Course number xxn1y0 xxs3y0 xxr3y0 xxt4y0 xxc4y0 xxd1y0 xxd4y1 xxd4y2 xxd7y0 xxd8y1 xxd8y3 7 P a g e

8 M.Tech. Major Project Part 2 M.Tech. Major Project Part 2 (Alternative) xxd8y2 xxd8y4 Each course is associated with a certain number of credits. Credit System: Education at the University is organized around the semester-based credit system of study. A student is allowed to attend classes in a course and earn credit for it, only if he/she has registered for that course. The prominent features of the credit system are a process of continuous evaluation of a student s performance/progress and flexibility to allow a student to progress at an optimum pace suited to his/her ability or convenience, subject to fulfilling minimum requirements for continuation. A student s performance/progress is measured by the number of credits that he/she has earned, i.e. completed satisfactorily. Based on the course credits and grade obtained by the student, grade point average is calculated. A minimum grade point average is required to be maintained for satisfactory progress and continuation in the programme. Also a minimum number of earned credits and a minimum grade point average should be acquired in order to qualify for the degree. All programmes are defined by the total credit requirement and a pattern of credit distribution over courses of different categories. Course Credits Assignment: Each course, except a few special courses, has a certain number of credits assigned to it depending upon its lecture, tutorial and laboratory contact hours in a week. This weightage is also indicative of the academic expectation that includes in-class contact and self-study outside of class hours. Lectures and Tutorials: One lecture or tutorial hour per week per semester is assigned one credit. Practical/Laboratory: One laboratory hour per week per semester is assigned half credit. Some courses arewithout credit and are referred to as non-credit (NC) courses. Example: Course EEL101 Fundamentals of Electrical ; 4 credits (3-0-2) The credits indicated for this course are computed as follows 3 hours/week lectures = 3 credits 0 hours/week tutorial = 0 credit 2 hours/week practical = 2 x 0.5 = 1 credit Total = = 4 credits Also, (3-0-2) 4 credit course = (3 h Lectures + 0 h Tutorial + 2 h Practical) per week = 5 contact hours per week For each lecture or tutorial or practical credit, the self-study component is 1 hour/week (for level courses) and 2 hours/week (for level courses). In the above example, the student is expected to devote = 4 hours per week on self study for this course, in addition to class contact of 5 hours per week. Earning Credits: At the end of every course for which a student has registered, a letter grade is awarded in each course for which a student had registered. On obtaining a pass grade, the student accumulates the course credits as earned credits. A student s performance is measured by the number of credits that he/she has earned and by the weighted grade point average. A student has the option of auditing some courses. Grades obtained in these audit courses are not counted for computation of grade point average. However, a pass grade is essential for earning credits from an audit course; this does not apply to postgraduate programmes. A minimum number of earned credits are required in order to qualify for a degree and continuation of registration at any stage. Currently students in the postgraduate programmes can opt audit courses but they do not count towards earned credits. The credit system enables continuous evaluation of a student s performance and allows the students to progress at an optimum pace suited to individual ability and convenience, subject to fulfilling minimum requirement for continuation. Course Content Description Course content description consists of following components: (i) Course Number, (ii) Title of the Course; (iii) Credit and L-T-P; (iv) Pre-requisites; (v) Overlapping/Equivalent courses; and (vi) Description of the content. An example is given below: 8 P a g e

9 EEL311 Graph Theory and its Application to Electrical Pre-requisites: CSL201 Overlaps with: MAL376, MAL468 Basic of graph theory: trees, f-circuits, f-cutsets, connected and seperable graphs etc. Matrices of a graph and relations between them. Generation of network functions of one and two-port networks using spanning tree and directed tree algorithms. Graph searches like BFS and DFS. Path problems like shortest paths, all paths between a pair of nodes etc. Generation of directed graphs and their use in the determination of transfer functions of networks. Applications of graph algorithms in routing, assignment and other problems in VLSI design. Pre-requisites Each course, other than 100 level courses, has specified pre-requisites which may be another course or a fixed number of earned credits or both. A student who has not obtained a pass grade, viz., A, A(-), B, B(-), C, C(-), D, NP or S, in the pre-requisite or has not earned requisite number of credits will not be eligible to do that course. Examples: AML310 Computational Mechanics Pre-requisite:AML140/AML150/AML160/AML170/AML180/CHL231/CHL204 and E.C. 60 A student who has obtained a pass grade in any one of the courses AML140, AML150, AML160, AML170, AML180, CHL231, or CHL204, and has earned 60 credits will be eligible to register for this course. BEL702 Bioprocess Plant Design Pre-requisite: AML110 & MEL110 & CHL205 & CHL204 & BEL401 and E.C. 90. A student who has obtained a pass grade in all these courses AML110, MEL110, CHL205, CHL204, and BEL401, and has earned 90 credits will be eligible to register for this course Overlapping/Equivalent courses Wherever applicable, for a given course overlapping and equivalent courses have been identified. A student is not permitted to earn credits by registering for more than one course in a set of overlapping/equivalent courses. Departments may use these overlapping/equivalent courses for meeting degree/pre-requisite requirements in special circumstances. Example: EEL301 Control - I Overlapped course: MEL312, CHL261 A student who has earned a pass grade in EEL301 will not be eligible to register for and earn credits, under any category, for either MEL312 or CHL261. Further, registration in an overlapping course as an alternative to a core course of his/her programme is not allowed. Course Coordinator Every course is usually coordinated by a member of the teaching staff of the Department/School which is offering the course in a given semester. For some courses, faculty from other departments or even guest faculty participates in the teaching and/or coordination of a course. This faculty member is designated as the Course Coordinator. He/she has the full responsibility for conducting the course, coordinating the work of the other members of the faculty as well as teaching assistants involved in that course, holding the tests and assignments, and awarding the grades. For any difficulty related to a course, the student is expected to approach the respective course coordinator for advice and clarification. The distribution of the weightage for tests, quizzes, assignments, laboratory work, workshop and drawing assignment, term paper, etc. that will be the basis for award of grade in a course will be decided by the course coordinator of that course and generally announced at the start of the semester. Course coordinator will have additional evaluation components over and above two minors and majors. Grading System 9 P a g e The grading reflects a student s own proficiency in the course. While relative standing of the student is clearly indicated by his/her grades, the process of awarding grades is not necessarily based upon fitting performance of the class to some statistical distribution. The course coordinator and associated faculty for a course formulate appropriate procedure to award grades that are reflective of the student s performance vis-à-vis instructor s expectation. The credit system enables continuous evaluation of a student s performance, and allows the students to progress at an optimum pace suited to individual ability and convenience, subject to fulfilling minimum requirement for continuation. The grades and their description, along with equivalent numerical points where applicable are listed in Table below- Table 3 : Grade Points Grade Grade Points Description A 10 Outstanding

10 A (-) 9 Excellent B 8 Very good B (-) 7 Good C 6 Average C (-) 5 Below Average D 4 Marginal E 2 Poor F 0 Very poor I - Incomplete NP - Audit pass NF - Audit fail W - Withdrawal X - Continued S - Satisfactory completion Z - Course continuation Description of grades 10 P a g e A grade An A grade stands for outstanding achievement. The minimum marks for award of an A grade are 80%. However, individual course coordinators may set a higher performance requirement. C grade The C grade stands for average performance. This average performance refers to average as per instructor s expectations in a holistic sense. D grade The D grade stands for marginal performance; i.e. it is the minimum passing grade in any course. The minimum marks for award of D grade is 40%, however, individual course coordinators may set a higher marks requirement. E and F grades A student who has scored marginally close to D in a subject can be awarded an E Grade. The Course Coordinators are, however, free to enhance this limit but should keep the percentage about 10% less than the cut-off marks for D Grade. The Course Coordinators can also specify any additional requirements (to be specified at the beginning of the Semester) for awarding E Grade. Students who obtain an E Grade will be eligible to take a Re-major test (an examination with weightage same as that of Major). For every Re-major student wants to appear, he/she has to pay fee prescribed by the University. If they perform satisfactorily, they become eligible for getting the grade converted to a D Grade; otherwise they will continue to have E Grade. However, the student will have only one chance to appear for Re-major for an E Grade. The Re-major test will be conducted within the first week of the next semester. The date of Re-major test of first year courses will be centrally notified by the Chairman, Time-Table Committee. A student can take a maximum of three such Remajor tests in a given semester. If a student can not appear for the Re-major test due to any reasons, he/she will not get any additional chance. A student has to repeat all core courses in which he/ she obtains F Grades until a passing grade is obtained either in summer semester or regular semester (provided slot is free). E & F Grades are not counted in the calculation of the CGPA; however, these are counted in the calculation of the SGPA. I grade An I grade denotes incomplete performance in any L (lecture), P (practical), V (special module) category courses. It may be awarded in case of absence on medical grounds or other special circumstances, before or during the major examination period. The student should complete all requirements within a) 10 days of the last date of Major Tests; the request is to be made to the head of the department of the student s programme who will notify the same to concerned course coordinators, or b) With permission of the Dean (UGS)/Dean (PGS&R), the period can be extended to the first week of the next semester. A student will be eligible for an I grade provided he/she has met the attendance criterion. Upon completion of all course requirements, the I grade is converted to a regular grade (A to F, NP or NF). I grade does not appear permanently in the grade card. Requests for I-grade should be made at the earliest but not later than the last day of major tests. Attendance in the course for which I-grade is being sought will be certified by the course coordinator of the course. The course coordinators can instruct all students awarded I or extended I grade to appear for the Remajor of the `E grade. On the basis of their performance a student having I grade or extended I grade can earn any permissible grade unlike students taking Re-major after obtaining E grade. If any I Grade student does

11 not appear in Re-major exam, it will be automatically converted to F Grade and will have to complete the course in summer semester. NP and NF grades These grades are awarded in a course that the student opts to audit. Only elective courses can be audited. Auditing a course is allowed until one week after the first Minor Tests. The audit pass (NP) grade is awarded if the student s attendance is above 75% in the class and he/she has obtained at least D grade. Course coordinator can specify a higher criterion for audit pass at the beginning of the semester. If either of these requirements is not fulfilled, the audit fail (NF) grade is awarded. The grades obtained in an audit course are not considered in the calculation of SGPA or CGPA. For UG programmes: the credits will be counted in total earned credits in the respective category. For PG programmes: the credits will not be counted towards degree completion credit requirements. W grade A W grade is awarded in a course where the student has opted to withdraw from the course. Withdrawal from a course is permitted until one week after the first Minor Tests. Withdrawal from PG major project part 2 is allowed only if he/she is given semester withdrawal. The W grade stays on grade card. X grade The X grade is awarded for incomplete work typically in a project-type course based on a request by the student. The X grade is awarded for incomplete work in Independent Study, Mini Project, Minor Project, or Major Project Part 1 and Part 2, based on the request of the student. On completion of the work, X grade can be converted to a regular grade within the first week of the next semester. Otherwise, the student will be awarded X grade on a permanent basis and it will appear in his/her grade card. Further, the student will be required to register for the course in the next semester. The credits of the course will be counted towards his total load for the semester. In case of Major Project Part 1, the student will not be permitted to register for Major Project Part 2 simultaneously as Major Project Part 1 is a pre-requisite for Major Project Part 2. A regular full-time student can be awarded X grade only once in a course, other than the summer semester. S and Z grades The S grade denotes satisfactory performance and completion of a course. The Z grade is awarded for noncompletion of the course requirements, and if it is a core course, the student will have to register for the course until he/she obtains the S grade. The specific courses in which S/Z grades are awarded are: a. Introduction to the Programme b. Practical Training c. NCC/NSO/NSS d. Introduction to Humanities and Social Sciences e. Professional Practices Evaluation of Performance The performance of a student will be evaluated in terms of three indices, viz. the Semester Grade Point Average (SGPA) which is the Grade Point Average for a semester, Cumulative Grade Point Average (CGPA) which is the Grade Point Average for all the completed semesters at any point in time, and Degree Grade Point Average (DGPA). The Earned Credits (EC) is defined as the sum of course credits for courses in which A - D or NP or S grades have been obtained. Points earned in a semester = Σ (Course credits x Grade point) for courses in which A - D grade has been obtained) The SGPA is calculated on the basis of grades obtained in all courses, except audit courses and courses in which S/Z grade is awarded, registered for in the particular semester. SGPA = Points secured in the semester Credits registered in the semester, excluding audit and S/Z grade courses The CGPA is calculated on the basis of all pass grades, except audit courses and courses in which S/Z grade is awarded, obtained in all completed semesters. 11 P a g e

12 CGPA = Cumulative points secured in all passed courses (A D grade) Cumulative earned credits, excluding audit and S/Z grade courses An example of these calculations is given in table Table 4: Typical Academic performance calculation-i Semester Course no. Course credits Grade Awarded Earned credits Grade Points Points secured (column 1) (column 2) (column 3) (column 4) (column 5) (column 6) MALXXX 5 C CSLXXX 4 C (-) PHLXXX 4 A PHPXXX 2 B MELXXX 4 E TTNXXX 2 S Credits registered in the semester (total of column 2) = 21 Credits registered in the semester excluding audit and S/Z grade courses = 19 Earned credits in the semester (total of column 4) = 17 Earned credits in the semester excluding audit & S/Z grade courses= 15 Points secured in this semester (total of column 6) = 114 Points secured in this semester in all passed courses (total of column 6 with A-D grade in courses) = 106 Points secured in the semester SGPA = Credits registered in the semester excluding audit and S or Z grades Courses = = CGPA = Cumulative points secured in all passed courses (A D grade) Cumulative earned credits, excluding audit and S/Z grade courses = = Semester Performance: Earned credits (E.C.) = 17 SGPA = Cumulative Performance: Earned credits (E.C.) = 17 CGPA = Table 5: Typical Academic Performance Calculations - II Semester Course no. Course credits Grade Awarded Earned credits Grade Points Points secured (column 1) (column 2) (column 3) (column 4) (column 5) (column 6) MALXXX 5 B EELXXX 4 A (-) CYLXXX 4 W CYPXXX 2 B (-) MELXXX 4 C AMLXXX 4 A HUNXXX 1 S Credits registered in the semester (total of column 2) = 24 Credits registered in the semester excluding audit and S/Z grade courses = 23 Earned credits in the semester (total of column 4) = 20 Earned credits in the semester excluding audit & S/Z grade courses = P a g e

13 Points secured in this semester (total of column 6) = 154 Points secured in this semester in all passed courses (total of column 6 with A-D grade in courses) = 154 Cumulative points earned in all passed courses = 106 (past semesters) (this semester) = 260 Cumulative earned credits = 17 (past semesters) + 20 (this semester) = 37 SGPA = PointsSecuredinthesemester CreditregisteredinthesemesterexcludingauditandSorZgradeCourses = = CGPA = Cumulativepointssecuredinallpassedcourses(A Dgrade) = CumulativeearnedcredutsexculdingauditandSorZgradecourses = Semester Performance: Earned credits (E.C.) = 20 SGPA = Cumulative Performance: Earned credits (E.C.) = 37 CGPA = On completion of all the degree requirements, the degree grade point average, DGPA, will be calculated and this value will be indicated on the degree/diploma. The DGPA will be calculated on the basis of category-wise best valid credits required for graduation. A student, who has earned the requisite credits but does not meet the graduation DGPA requirement, may do additional courses in any elective category to meet the DGPA requirement within the maximum permissible time limit. 4. REGISTRATION AND ATTENDANCE 4.1. Registration Registration is a very important procedural part of the academic system. The registration procedure ensures that the student s name is on the roll list of each course that he/she wants to study. No credit is given if the student attends a course for which he/she has not registered. Registration for courses to be taken in a particular semester will be done according to a specified schedule before the end of the previous semester. Each student is required to complete the registration form and deposit the semester fee well in advance. Various activities related to registration, the relevant dates are included in the Semester Schedule that is available before the start of the semester Registration And Student Status Registration by a student confirms his/her status as student at the University. Failure to register before the last date for registration will imply that the student has discontinued studies and his/her name will be struck-off the rolls. Every registered student is considered as a full-time student at the University. They are expected to be present at the University and devote full time to academics. Students registered only for a self-study course or only for project or thesis are also considered as full-time students Advice On Courses At the time of registration, each student must consult his/her Mentor/programme coordinator to finalize the academic programme, keeping in view factors, such as, minimum/maximum numbers of total lecture credits, past performance, backlog of courses, SGPA/CGPA, pre-requisite, work load and student s interests, amongst others Registration Validation Before the first day of classes, every student is required to be present on campus and validate his/her registration by logging in at the system or manually. The updated registration record will be available on the website and the hard copy will be available with the student s advisor/programme coordinator / Examination Section. Students who do not register themselves will not be permitted to add/drop courses. However, for the first semester, all the courses are compulsory and students need not to do this exercise Minimum Student Registration In A Course 13 P a g e

14 All the core courses will run as per their occurrence in the semester. Elective undergraduate courses (100, 200, 300, 400 level course) will run if minimum of 12 students register for the course. Under special circumstances, a departmental elective course may be allowed to run with minimum registration of 8 students, with prior permission of Chairman, Academic Council. An elective 700 or 800 level course can run with minimum of 4 students. This checking will be done on the last date for Add/Drop. Courses without the minimum enrolment will be dropped by the UG/PG section. The students who had registered for these courses will be de-registered, and they will be given one more day for adding a course in lieu of the dropped course Late Registration Late registration is permitted under the following conditions: A student, who was not in the campus during the period of registration in the previous semester, needs to complete the registration process on or before the first day of the semester before commencement of classes; or For reasons beyond his/her control, if a student is not able to register or send an authorized representative with a medical certificate, he/she may apply to the Dean (UGS)/Dean (PGS&R) for late registration. Dean (UGS)/Dean (PGS&R) will consider and may approve late registration in genuine cases on payment of an extra fee called late registration fee. Late registration is permitted until one week after the start of the semester Addition, Deletion, Audit And Withdrawal From Courses (From 3rdSemester Onwards) Add/Drop: A student has the option to add a course(s) that he/she has not registered for, or drop a course(s) for which he/she has already registered for. This facility is restricted to the first week of the semester. Audit: A student may apply for changing a credit course to an audit one within one week of the end of the first minor test. Withdrawal: A student who wants to withdraw from a course should apply within one week of the end of first minor test. A withdrawal grade (W) will be awarded in such cases Semester Withdrawal Semester withdrawal and absence for a semester under different conditions viz. (i) medical and personal grounds (ii) industrial internship (iii) exchange / deputation to another academic institution in India or abroad, & (iv) disciplinary condition (for both UG and PG students) should be clearly identified. Semester Withdrawal (SW) is proposed to reflect the condition in which a student is forced to withdraw from all courses in the semester for medical conditions. A student can apply for semester withdrawal if he /she has missed at least 20 teaching days on this ground. Under no circumstances an application for semester withdrawal shall be acceptable after the commencement of major exam. A student is not permitted to request for withdrawal with retrospective effect. Semester Leave (SL) is proposed to indicate the situation in which a student is permitted to take one or more semester off for industrial internship or any other assignment with prior approval and planning. The application is to be routed through his/her advisor / programme coordinator and HOD and the final approving authority will be Dean. All such applications must be processed before the beginning of the semester in which the leave will be taken. When a student (UG or PG) registers at another academic institution in India or abroad with the expectation of credit transfer or research work through a pre-approved arrangement including MoU, the student should be considered as being on a Semester Exchange (SE). The SE period will be counted towards the total period permitted for the degree. When a student is suspended for one or more semesters on disciplinary grounds, the student status should be called Disciplinary Withdrawal period (DW). Time spent in DW status will be counted towards the total period permitted for completion of the degree Registration In Special Module Courses Special module courses, i.e. V category courses, can be offered at the beginning of the semester in which case the regular registration procedure will be followed. V -Category courses may also be offered during the semester, in such a case, student will be allowed to add this course before the classes for the course begin Registration For The Practical Training Before proceeding for practical training or training as part of curricular requirement, the student should register for the respective course after obtaining approval from the training coordinator and head of the department. On returning after training a continuation grade will be awarded and the students must register for the course in the regular semester immediately following the training period. During this semester, evaluation of the training will be carried out and regular grade will be awarded. 14 P a g e

15 4.11. Pre-requisite Requirement For Registration A student should register for a course only if he/she fulfills the pre-requisite requirement(s). If the prerequisite course is being done at the time of the registration the pre-requisite check will be performed after grading is done for the semester and those not fulfilling the pre-requisite will be deregistered from the course Overlapping/Equivalent Courses A student is not allowed to earn credits from two overlapping/equivalent courses. Overlapping/equivalent courses are specified along with each course Limits on Registration A student is permitted to register for specified minimum and maximum number of credits and/or lecture credits. Details are given in section 3.19, Table-7 for all programmes Registration and Fees Payment Every registered student must pay the stipulated fees in full before the specified deadlines. In the event that a student does not make these payments, he/she will be de-registered from all courses and his/her name will be struck-off the rolls Registration Record The student should ensure that the entries related to registration are entered on the Registration Record. Queries related to registration will be considered only when accompanied by the original Registration Record. This record must be preserved until the semester grade card is received by the student Continuous Absence And Registration Status If a student is absent from the University for more than four weeks without notifying the Head of Department/Dean, his/her registration will be terminated and name will be removed from the University rolls Attendance Rule a) It is mandatory for the students to attend all classes. Attendance Records of all students for each course will be maintained. b) For all 1 st year courses the attendance will be taken and maintained by U.G. Section. If any student s attendance falls below 75% attendance in any of these courses, he/she may be put under academic probation. Henceforth, he/she will be governed by the rules for student under academic probation. c) For all other courses, the Course Coordinator will announce the class policy on attendance with respect to grading etc., at the beginning of the semester. This shall be done keeping in mind the importance of classroom learning in the teaching-learning process. Once the class attendance policy has been made clear to all the students registered for the course, the Course Coordinator will implement the same in totality. For the purpose of attendance calculation, every scheduled practical class will count as one unit irrespective of the number of contact hours. Attendance record will be maintained based upon roll calls (or any equivalent operation) in every scheduled lecture, tutorial and practical class. The course coordinator will maintain and consolidate attendance record for the course (lectures, tutorials and practicals together, as applicable). A faculty may choose any one or more of the following as attendance policy (Approved by the Vice Chancellor): a) Faculty can assign 10% of the total marks to surprise quiz. If attendance of the student is greater than 90%, result of the best three quizzes will be considered else average of all quizzes will be considered. b) Faculty can allocate specific marks for participation in discussions in the class on a regular basis. c) If a student s attendance is less than 75% (up to 65 %), the student will be awarded one grade less than the actual grade that he (she) has earned. For example, a student who has got A grade but has attendance less than 75% will be awarded A-grade. d) A student cannot get NP for an audit course if his attendance is less than 75%. 15 P a g e A faculty can implement any other attendance policy provided the policy is approved by the Vice Chancellor.Attendance statistics will also be used in the following way: a) If a student s attendance is less than 75% in more than two courses without any valid reason in a semester, will be issued warning and put under probation. If this is repeated for more than one semester then the

16 university has the option of striking his name from the university based on the recommendation of the committee setup by the Vice Chancellor. b) If a student s attendance is less than 75% in any course and CGPA is less than 6.0, then he (she) will not be eligible to hold any position of responsibility in the hostel/university in the next semester Absence During The Semester a) A student must inform the Dean/Academic Section immediately of any instance of continuous absence from the classes. b) A student who is absent due to illness or any other emergency, up to a maximum of two weeks, should approach the course coordinator for make-up quizzes, assignments and laboratory work. c) A student who has been absent from a minor test due to illness should approach the course coordinator for a make-up test immediately on return to class. The request should be supported with a medical certificate from registered medical practitioner prescribed by University. A certificate from a registered medical practitioner will also be acceptable for a student normally residing off-campus provided registration number of the medical practitioner appears explicitly on the certificate. d) In case a student cannot appear in a minor test on the same day in which he/she has appeared in a test, a medical certificate only from the registered medical practitioner prescribed by University will be acceptable. e) In case of absence on medical grounds or other special circumstances, before or during the major examination period, the student can apply for I-grade. 75 % attendance in a course is necessary for being eligible for request of I-grade in that course. An application requesting I-grade should be made at the earliest but not later than the last day of major tests. The application should be made to the Head of the Department of the student s programme who will grant approval depending on the merit of the case and inform course coordinators and U.G section. The student should complete all course requirements within ten days of the last date of Major Tests. The I-grade will then be converted to a proper grade (A to F, NP or NF). f) In special situations arising due to the student s inability to be present at the University during the stipulated period, in (e) above, the period for conversion of I grade can be extended to the first week of the next semester. Approval for this extension can be granted by Dean (UGS) on recommendations of the concerned Head of the department, course coordinators and concerned warden. A request to this effect must be included in the application for I-grade. g) In case the period of absence on medical grounds is more than 20 working days during the semester, a student may apply for withdrawal from the semester, i.e. withdrawal from all courses registered that semester. Such application must be made as early as possible and latest before the start of the major tests. No applications for semester withdrawal will be considered after the major tests have commenced. Dean, depending on the merit of the case, will approve such applications. Partial withdrawal from courses registered in a semester is not allowed. h) If a student is continuously absent from the University for more than four weeks without notifying the Dean, his/her name will be removed from University rolls Change Of Department Branch/Program At The End Of First Year: Branch Change i. All branch transfers can be effected only once at the beginning of the second academic year. No application for change of branch during the subsequent academic years will be entertained. The decision on the student's application will be made only after receiving the CGPA of the second semester. ii. The student with good academic record and securing not less than 8.00 CGPA and without having E or F grade in any subjects of previous semesters shall remain eligible for applying branch change. iii. iv. The student will be required to submit dully filled Branch / Programme change Form clearly mentioning branch of his choice in priority with prescribed Branch Change Fee. The decision on the student's application will be made only after receiving the CGPA of the second semester. v. The shifting of students through branch shall be rationalized and the total strength of any branch shall not be allowed to reduce from 85% and increased by 15% vi. vii. viii. ix. An eligible applicant who has secured a CGPA of 10.0 shall be allowed a change of branch of his/her choice without any constraint. Branch change applications will be strictly considered on the basis of Merit as established by the CGPA and only to the extent of the applicant's choices and the order of the preferences expressed in the application. In case more than one student with the same CGPA seek the identical change, branch-to-branch, first their percentage of marks in class 12 th and then 10 th shall be examined and those with higher shall be allowed. The student allotted new branch, subject to the approval of Vice Chancellor may be allowed to return to his/her original branch within 15 days from the commencement of the session. 16 P a g e

17 x. In exceptional cases, the Chairman may also grant a change of branch to a student who is in distress in his/her present branch. Branch change of this category may be granted in rare cases subject to the satisfaction of the Committee that compelling grounds for the same do exist Rules for Program Change i. All branch transfers can be effected only once at the beginning of the second academic year. No application for change of branch during the subsequent academic years will be entertained. The decision on the student's application will be made only after receiving the CGPA of the second semester. ii. iii. iv. The student who have secured not less than 8.00 CGPA and does not have E or F grade in any subjects of previous semesters shall remain eligible for applying programme change. A student registered for integrated dual degree program in a Branch can be permitted to change his/her Program of same branch provided his Graduation degree part remains same in which he takes admission. The student will be required to submit dully filled Branch / Programme change Form clearly mentioning program of his choice with prescribedprogram Change Fee. v. The student shall be allowed to give one choice of change only. vi. vii. viii. ix. The decision on the student's application will be made only after receiving the CGPA of the second semester. The shifting of students through branch shall be rationalized and the total strength of any branch shall not be allowed to reduce from 80% and increased by 20% Fees Deposited in 1 st year will not be Adjusted in next Semester. New Program fee will be applicable from 3 rd semester. All Program Change can be effected only once at the beginning of the second academic year. No application for change of program during the subsequent academic years will be entertained. 5 UNDERGRADUATE DEGREE REQUIREMENTS, REGULATIONS AND PROCEDURES 5.1 Overall Requirements B.Tech. The total credit requirement for the B.Tech. (4-year programme) is 150 credits. For B.Tech. programmes and undergraduate part of the dual degree programmes, the total credits are distributed over two categories: undergraduate core (UC) and undergraduate elective (UE). The Undergraduate core (UC) has following categories: i. Basic Sciences (BS) which include Mathematics, Physics and Chemistry courses. ii. Arts and Sciences (EAS) which include fundamental engineering courses. iii. iv. Departmental Core (DC) which include courses of relevant discipline. Undergraduate electives (UE) courses belong to basically three categories: Departmental Electives (DE): Electives related to the parent discipline. v. Humanities and Social Sciences, and Management (HU &HM): Electives to provide a wide exposure to different areas of Humanities, Social Sciences and Management. Open Category (OC): Electives to provide an opportunity to the student to develop broad inter-disciplinary knowledge base or to specialize significantly in an area outside the parent discipline DualDegree Programmes (Major + Minor) The total credit requirement for the Dual Degree programmes is165(150+15) credits. The B.Tech. credit requirements are same as those in for the B.Tech. (4-year programme) but with major project parts 1 and 2 excluded IntegratedM.Tech. Total credit for the integrated M.Tech. programme is divided into two categories: i. Programme Core (PC): Core courses related to the M.Tech. Specialization. ii. Programme Electives (PE): Elective courses related to the M.Tech. specialization. Programme Core and Programme Electives have components similar to those of the undergraduate core and undergraduate electives, respectively. 5.2 Degree Requirements Breakup 17 P a g e The degree requirements for the various programmes listed earlier are detailed below.

18 5.2.1 Earned Credits i. Completion of 150 earned credits for 4-year B. Tech. Programmes. ii. Completion of earned credits for Integrated M.Tech. programme. These credits are needed to be earned under different categories as specified in Section 4 for individual programmes DegreeGradePointAverage (DGPA) Requirement A student must obtain a minimum DGPA of 5.0 to be eligible for award of the B.Tech.,Integrated M.Tech., dual degree and M.Tech.part time and full time programme. All exceptions to the above conditions will be dealt with as per following regulations: a) If a student completes required credits for B.Tech./Integrated M.Tech. with DGPA less than 5, thenthe student will be permitted to do additional elective courses under appropriate category to improve the DGPA within themaximum time limit for completion of B.Tech./ M.Tech. degree respectively, as the case may be. In case a DGPA of 5 or more is achieved within the stipulated period, a B.Tech./Integrated M.Tech. degree will be awarded and in case the same is not achieved no degree will be awarded. b) If a student completes requisite credits for Dual Degree Programme: (i) With B. Tech. DGPA less than 5 but M.Tech. DGPA more than 5.0 The student will be permitted to do additional elective courses (under any appropriate category) to improve the DGPA for completion of B. Tech. part within the maximum time limit. In case a DGPA of 5 or more is achieved for B.Tech., the student will be eligible for award of the both B.Tech. & M. Tech. degree and in case the same is not achieved no degree will be awarded. (ii) With B. Tech. DGPA more than 5 but M. Tech. DGPA less than 5.0 The student will be eligible for grant of only B.Tech. degree provided a written request is made to the Academic council. Alternatively, the student may opt to do additional elective courses (PE category only) to improve the DGPA within the maximum time limit. If no programme elective (PE) courses are available, other relevant 700 and 800 level courses as certified by the department can be done for the purpose of improving the DGPA. In case DGPA of 5.0 or more is achieved for the M. Tech. part, the student will be eligible for award of the both degrees B.Tech. & M.Tech. However, in case the same is not achieved at the end of stipulated period, the student will be eligible for the award of only B. Tech. degree, provided a written request for the same is made to the academic council. (iii) With B. Tech. DGPA less than 5.0 and M. Tech. DGPA is also less than 5.0 The student will be permitted to do additional elective courses (under any category) to improve the DGPA for completion of B. Tech./M. Tech. degrees (PE category only) within the maximum time limit. (If no programme electivecourses are available, relevant 700 and 800 level courses as certified by the department can be done for the purposeof improving the DGPA of the M.Tech. part). In case a DGPA of 5 or more for B.Tech. and 5.0 or more for M.Tech. is achieved, the student will be eligible for award of the Dual Degrees (B.Tech. & M.Tech.). However, in case a DGPA 5 or more for B.Tech. is achieved but the DGPA 5.0 or more for M.Tech. is not achieved at the end of stipulated period, the student will be eligible for award of only B.Tech. degree provided a written request for the same is made to the Academic council. c) A student is eligible to apply for a Diploma provided he/ she has earned 120 credits and has exhausted the maximum number of permitted registered semesters for completion of his/ her degree. If the student has completed 60 credits (out of 120 credits) from his/ her DR+DC+PE+PC categories then the student will be awarded Undergraduate Diploma in respective discipline on completion. If the student has not completed 50% credits from these categories but has completed 120 credits then he/ she will be awarded Undergraduate Diploma in d) No self-study course will be permitted for the purpose of improvement of DGPA for M. Tech. or B.Tech. part PracticalTraining A student of the B.Tech., Dual-degree and Integrated M.Tech. programmes must complete the prescribed number of days of practical training to the satisfaction of the concerned department. This training will be normally arranged in the summer vacation following the 6 th semester. Practical training duration is a minimum of 50 working days. Practicaltraining should be carried out preferably in industry or R&D institutions in India. Practical training in academic institutions is not permitted. In some special cases the permission may be granted with prior approval of Academic Council NCC/NSS/NSO 18 P a g e All students are required to enroll for either one of NCC, NSS or NSO in their first year. This requirement should be completed in one year. If, however, a student is not able to complete this requirement in the first

19 year, he/she must complete it by the end of the 2nd year (4th semester). All students will need to attend 10 hours of Counseling sessions as part of these activities on compulsory basis Break-Up Of Earned Credits The minimum earned credit requirements for the B.Tech., Dual Degree and Integrated M.Tech. programmes along with detailed break-up of the credits in various categories are given in Table below. Maximum of 6 credits under open category can be taken from the departmental U.G. or P.G. courses, and other programme-relevant courses as identified by the department. For completing graduation requirements, a student must complete a minimum of 8 credits of Mathematics category courses, and 6 credits each of Physics and Chemistry category courses with a valid pass grade. A student must also earn valid credits (audit not permitted) for a course of Environment Studies category under OC for graduation. Table 6: Degree requirements of undergraduate programmes P rogramme SN C a t e g or y S y m b o l B.Tech (4 yr) Dual Degree (Major + Minor) Integrated M.Tech Basic Sciences* BS 18 (min.) 18 (min.) 18 (min.) 1.2 Arts and Sciences EAS 16 (min.) 16 (min.) 16 (min.) 1.3 Humanities and Social Sciences HU+HM 16 (min.) 16 (min.) 16 (min.) 2.2 Departmental Core DC 50 (min.) 50(min.) 50(min.) 2.2 Departmental Electives DE 20 (min.) 20 (min.) 40 (min) DE+PE 2.3 Open category* OC 10 (min.) 25 (min.) 15 (min.) Departmental requirement TOTAL REQUIREMENT DR (DC+DE) 90 (min.) 90 (min.) 80 (min.) 4.1 (B.Tech./Integrated) TOTAL REQUIREMENT M.Tech PR Programme core PC Programme elective PE TOTAL REQUIREMENT M.Tech. TOTAL REQUIREMENT (Dual degree) PR (PC+PE) * Minimum of 8 Credits can be earned through departmental courses UR+PR Audit Courses Audit facility is open to all students who have completed 100 earned credits. A student will be permitted to do any number of audit courses over and above the graduation requirements. The audit rules are: (a) B.Tech. (4-Year) Programme: A maximum of 8 credits from the elective courses in any category out of 150 credits required for B.Tech. degree may be completed on audit basis. (b) Dual-degree Programme: A maximum of 8 credits from the elective courses in any category may be completed on audit basis from the UG part of the programme. (c) Integrated M.Tech. Programme: A maximum of 8 credits from the elective courses in any category may be completed on audit basis. For completion of graduation requirements, a student must complete a minimum of 8 credits of Mathematics category courses and 6 credits each of physics and chemistry category courses with valid pass grade. A student must also earn valid credits (audit not permitted) for a course of Environmental Studies Category. 5.3 Lower And Upper Limits For Credits Registered 19 P a g e

20 A student must register for a minimum of 12 credits and a maximum of 27 credits in a semester. The minimum andmaximum lecture credits that a student can register for in a semester are 9 and 18, respectively except the 8 th semester of B.Tech programme when minimum credits are 9 and maximum credits are 18. For Integrated M.Tech. programmes, the above limits apply up to the 8 th semester. In the 9 th and 10 th semesters, these students will normally register for a minimum of 9 credits and a maximum of 22 credits per semester. Under exceptional circumstances a student can register for a maximum of 28 credits including not more than 6 (six) L (Lecture) courses. However, this will be permitted at most twice during the programme in semesters other than 1 st and 2 nd,and those in which the student is registered for Major Project Part 1 or 2.These conditions will not be applicable for those students who are on probation according to the criteria defined. 5.4 Conditions For Termination Of Registration, Probation And Warning a) If the performance at the end of first two registered semesters (not including summer semester) is poor, then the student can opt to start a fresh, or else his/her registration will be terminated. The criteria poor performance is defined in Table Table 7: Rules for termination of registration at the end of the 2nd registered semester. Quality of performance Poor performance If Earned credits (total of 1 st & 2 nd Sem ) B.Tech. <24 MBA <22 BBA <18 B.Com <18 M.Tech. <22 MCA <16 BCA <13 Decision Re-start (once only) or Termination of registration In case of Re-Start, student has to pay full semester fee prescribed by the University for that year. b) If a student chooses to restart after the first two registered semesters, then his/her credits earned and semesters registered will not be carried over. The re-start will be indicated on the transcript. The re-start will be permitted only once. If at the end of two registered semesters after re-start, the earned credits are less than as shown in table, then the registration will be terminated. c) Each student is expected to earn minimum number of credits as shown in table in each subsequent registered semester with a SGPA greater than or equal to 4.0. If the performance of a student at the end of any registered semester is below this minimum acceptable level, then he/she will be placed on probation and a warning shall be given to him/her and intimation sent to the parents. d) Table 8: Rules for minimum credits requirements to register in a semester Course Minimum Credits in 1 st Semester Minimum Credits in subsequent Semester Minimum SGPA Required B.Tech MBA M.Tech MCA BBA/B.Com BCA e) The student placed on probation shall be monitored, including mandatory attendance in classes, special tutorials and mentoring. Mentoring will comprise structured guidance under a senior/postgraduate student. f) If the performance of a student on probation does not meet the above criterion (b) in the following registered semester, then the student will be permitted to register by the Dean, only if the department makes a favourable recommendation. The Head of the Department s recommendation shall be prepared after consultation with the student, and should include (i) feasibility of completing the programme requirements, and (ii) identification of remedial measures for the problems leading to poor performance. g) The registration of any student will be limited to 1.25 times the average earned credits of the previous two registered semesters, subject to a minimum of 15 credits and a maximum of 26 credits. 5.5 Slow-Paced Programme 20 P a g e

21 (i) A student who has earned between 24 and 36 credits at the end of the first two registered semesters will be eligible to opt for the slow-paced programme. A student opting for such a programme shall be permitted two additional registered semesters for completing degree requirements. (ii) In the slow paced programme, the upper limit for credits registered in a semester will be 18. A student in this programme is expected to earn at least 12 credits with minimum SGPA 5.0 in any semester, falling which he/ she will be issued a warning and placed on probation. The student placed on probation shall be monitored, including mandatory attendance in special tutorials and mentoring. If the performance of a student on probation does not meet the above criterion in the following registered semester, then the student will be permitted to register by the Vice Chancellor only if the department makes a favorable recommendation. The Head of the Department s recommendation shall be prepared after consultation with the student, and should include (i) feasibility of completing the programme, and (ii) identification of remedical measures for the problems leading to poor performance. (iii) Slow-paced programme shall be defined by the respective department for each student. 5.6 Maximum Duration For Completing Degree Requirements 1. The maximum permitted duration of each programme will be determined in terms of number of registered regular semesters, hereinafter called registered semesters. Any semester in which a student has registered for a course will be called a registered semester subject to the following: (a) Only the 1 st and 2 nd semesters of an academic year can be registered semesters. The summer semester will not be considered as a registered semester. (b) A semester when a student has been granted semester withdrawal or granted leave will not be considered as a registered semester. (c) The semester when a student is suspended from the Institute on disciplinary grounds will not be counted towards the number of registered semesters. The summer semesters falling in between the permitted registered semesters shall be available for earning credits. After the student has registered for the maximum permissible number of registered semesters, the subsequent summer semesters will not be available for earning credits. 2. The maximum permissible number of registered semesters for completing all degree requirements would be: Table 9. Maximum permissible duration for completing degree requirements. Programme Name Maximum number of registered semesters permitted for completingdegree requirements B.Tech. 12 (*) Dual Degree 14 (*) Integrated M.Tech. 14 (*) Note: (*) If a student opt for the slow-paced programme (as defined in clause B1),then the maximum permissible number of registered semesters shall be increased by two semesters. 5.7 Courses Of Special Nature 21 P a g e Courses of special nature are: National Cadet Corps (N.C.C.), National Sports Organization (N.S.O.) and National Service Scheme (N.S.S); Introduction to the Programme, Introduction to Humanities and Social Sciences; IndependentStudy,MiniProject,PracticalTraining,Colloquium,andMajorProject.Salientfeaturesofthesecourses aregivenbelow. a) N.C.C.,N.S.O.and N.S.S. The B.Tech., Dual Degree and M.Tech. Integrated student have to complete 100 hours in any one of the activities, namely NCC, NSS, NSO to complete non-credit requirement. On completion of 100 hours, student is awarded S grade;100hoursrequirementoveraperiodofoneyearisbrokeninto50hoursrequirementpersemester. ThestudentisregisteredinNCN100/NSN100/NPN100levelcourseinthe1 st Semesterandonobtaining S grade he/she is registered in NCN101/NSN101/NPN101 in the 2 nd Semester. Unless a student obtains S grade in both100 and 101 level courses he/she does not complete the non-credit requirement of NCC, NSS, NSO. In case a studentcannotcompletethisrequirementinthefirstyear,hemustdosobytheendofsecondyear;otherwisehe/ shewillnotbeallowedtoregisterforanycourseuntilhe/shecompletesthisrequirement. b) Independent Study Independent Study is an elective course that some departments may offer from fourth semester onwards. It is a 3- credit course covering one or more of the following: (i) In-depth study and critical review of a specified topic;

22 (ii) Specialized laboratory work/experimental project/feasibility study; (iii) Work on a research project; (iv) Software development on a specified topic. An individual student and teacher should decide upon the topic and submit an initial write-up to get the approval ofthe Course Coordinator before the end of the semester when the course is registered for (i.e. in the semester priorto doing the course). The duration of the course will be the entire semester. A written report should be submitted bythe student on completion of the course. The student s performance will be evaluated by a departmental committeevia a mid-term and final evaluation. A student has to earn 80 credits and obtain at least 7.5 CGPA to become eligible to do Independent Study. 22 P a g e c) Mini Project An elective course under this title may be floated by departments from fifth semester onwards. Mini project will be a regular course to conduct a design and fabrication type project. The student and teacher would decide upon the topic, prepare a plan of work and get the approval of the Course Coordinator before the end of the semester when the course is registered for. The duration of the course will be the entire semester. A project report would be submitted by the student on completion of the course. The student s performance will be evaluated by a departmentalcommittee via a mid-term and a final evaluation. Mini-project can be done jointly by 2 students, each having earned 75 credits with a CGPA of at least 5.0. AnIntegrated M.Tech student can do either Mini Project or Minor Project. d) Practical Training Practical Training is a non-credit departmental core course (NC) to be done typically in the summer semester followingsixth semester. A student who has earned at least 75 credits at the end of 5 semesters is eligible to undergo practical training in the summer following sixth semester. The duration for practical training is 50 working days (minimum), preferably in an industry or R&D institution in India. Practical training in academic institutions is not permitted. It is the joint responsibility of the departments and the Training and Placement (T&P) unit to arrange for training forall their students. In the beginning of each academic session, T&P unit will prepare programme-wise lists of potential training organizations in consultation with the respective departments. These organizations will be approached by the T&P unit with a request to provide training seats. Consolidated lists of training offers will be made available to the students through departments in the beginning of the second semester of the session. If a student is interestedin making his/her own arrangement for the training seat, he/she will need to have the training organization approved and route the application through the departmental training in charge and T&P unit. All such applications must be completed before the end of first semester. No self-arranged practical training, not approved through the above process, will be allowed and faculty members will not sign any forms for the purpose. The department will appoint a training supervisor for each student. The supervisor is expected to keep contact with the assigned students through and /or telephone. The students will be required to get their training plan reviewed by their supervisor within the first week and report their progress on weekly basis. The supervisor, if desires, may visit the organization. Visits within the country will be supported by the institute. A student will be registered for practical training course in the summer semester in which the training is being done. At the end of the summer semester, a Z grade will be awarded and he/she should register for practical training course in the following semester. The Department will scrutinize the training report and the training certificate and will award S grade within the next semester, if the training is satisfactory. In case the training is considered to be unsatisfactory, a Z grade will be awarded and the student may have to undergo fresh practical training for a part or full duration. Practical Training and submission of summer training report is a mandatory requirement for graduation. e) Colloquium Colloquium is a 3-credit course and includes assessment of practical training. A student will be eligible to do Colloquium if he/she had registered for Practical Training earlier. Typically, a student will register for Colloquium in the regular semester following the summer semester in which he/she has done the practical training. f) B. Tech Project The B.Tech Major Project is structured into two parts - Core and Elective. The Core B.Tech Project will have 6 credits. It will be scheduled in the seventh semester. The Elective B.Tech project will be of 6 credits. The students will be eligible to do Elective B.Tech project, if he/she secures a grade not below C in Core B.Tech Project. Elective B.Techproject will be scheduled in the eight semester. All awards based on B.Tech project will consider performance in Elective B.Tech project. Those students who do notqualify or does not opt for Elective B.Tech Project will do DE category courses in its place to make up total credits. g) Major Project (Integrated M.Tech, 2yr M.Tech) The Major Project is a core course spread over at least two regular semesters and comprises of Part 1 and Part 2.The allocation of major projects, faculty guides and tentative plan of work are to be done typically before the end of the previous semester. Part 2 is generally the different project from part-1 project. Under special conditions student may allow to continue the work of Part 1 project in part 2 with prior approval of guide and academic council.

23 A mid-term assessment and an end semester assessment will be carried out for each part. Part 1 and Part 2 will be graded separately. C grade is considered as the minimum pass grade in each part of the M.Tech. Major Project in Integrated M.Tech. Programmes & 2 year M.Tech. Programmes. A student must have obtained a pass grade C in Project Part 1 in order to be eligible for registering for Project Part 2. Major project will be spanned over two regular semesters. Typically a student will register for the Part 1 of major project in regular semester. Mid-term evaluation of the M.Tech.Project Part 1 will be held within first two weeks of the corresponding semester. At the end of the regular semester, thestudent will be awarded a proper grade in M.Tech. Project Part 1. If he/she obtains a valid pass grade in thiscourse, he/she can register for M.Tech. Project Part 2 in the following regular semester. His/her M.Tech. Project Part 2 will be evaluated at the end of the corresponding semester as per the stipulated deadline. Norms for conducting M. Tech. project of M.Tech and Integrated M. Tech. programmes at location outside Career Point University. (a) (b) (c) (d) (e) (f) The student is permitted to work at location outside Career Point University, Kota in summer or in the 2 nd Semester of MTP when the student is not registered for other courses. Projects can be carried out at an University or Institute if it is linked through consultancy/sponsored project or covered under MoU. Else with approval of Dean on recommendation of HoD. However, the description of the proposed work must be approved by Department Committee. At the commencement of the project, a description of the proposed work will be made available and be approved by the Departmental Committee. An External Supervisor will be appointed by the Department with approval of the Head of the Department and conveyed to Dean and the vice chancellor of the university. The student is required to come back for mid-term evaluation / presentation. Special Module (V-category) Courses Special module courses are 1 or 2 credit courses that can be offered at the beginning of the semester or during thesemester. These courses will usually cover specialized topics that are not generally available in the regular courses. Eligible students can register for these courses for credit. The course coordinator will evaluate the students performance and award a letter grade. The credits so earned will count towards the appropriate category for degree completion purposes. 6 Open Category 6.1 Open Category Credits Open category credits should provide an opportunity to a student to exercise his/her options in an unrestricted fashion. a) A student can complete open category credits by choosing courses from different departments. The student will be permitted to register for maximum of 8 credits of departmental courses under open category. b) A student, if he (she) so desires, can complete 25 credits out of the Open Category basket by exercising one of the following options. (i) The 25 credits belong to one of the Minor Area programmes. (ii) The 25 credits could be utilized for inter-disciplinary specializations in which a student can earn credits by doing courses from multiple departments (including the parent department). Such specializations can be defined jointly by more than one participating department. Implementation Rules (i) It will be possible for a student to register for a minor area / inter-disciplinary specialization. Registration for a Minor Area / specialization will be based on the performance of the student in a qualifier course which will be one of the core courses for the Minor Area / specialization. Departments/Centers need to identify qualifier courses for the offered minor area programmes/specializations. In order to discourage non-serious students, if someone registers for a minor area / specialization but does not complete it, that information will be recorded on the academic transcripts. (ii) Interdisciplinary specialization: This requires two or more Departments/Centers to identify courses totaling 25 credits which will lead to an inter-disciplinary specialization. This will have courses from allthe participating Departments/Centers and will also have a core component totaling 6-8 credits. The specialization will be mentioned on the degree. (iii) A student opting for Departmental Specialization/Inter-disciplinary specialization will not have the option for registering for departmental courses for remaining open category credits. 6.2 Minor Area A set of pre-defined courses of total 25 credits in a focus area comprises a Minor Area. A student can use Open Category (OC) credits to complete the specific requirements. Any student is eligible to take the Minor Area at the end of the 3 rd semester and may register for Minor Area courses from 4 th semester onwards. 23 P a g e

24 A student registered in any programme of a specific department will not be eligible to take the minor area(s) offered by the same department; additional conditions and details of individual minor areas are given in Section 6. If any course of a minor area overlaps with any core course (DC or PC category courses) or elective course (DE or PE category courses) of the student s programme, then credits from this course will not count towards the minorarea credit requirements, though this course may contribute towards satisfying the core requirement of the minor area. In such a case, the requirement of 25 credits must be completed by taking other courses of the minor area. For purposes of completing minor area requirements, the listed minor area course may be substituted by an equivalent course so identified in the course descriptions. 6.3 Self-study Course A self-study course will be from the regular UG courses. The main features of a self-study course are as follows: (a) (b) (c) (d) (e) (f) (g) (h) (i) A student may be given a self-study course of weight age not exceeding 5 credits in the final semester if he/ she is short by a maximum of 5 earned credits required for graduation provided that the course is not running in that semester as a regular course. Students in the M.Tech.and Integrated M.Tech. programmes are allowed to avail of this provision during their last semester. However, they would be permitted to take only a UG course as a possible self-study course. A student can make use of this provision only once during the programme. A student may also be permitted to do a U.G. core course not exceeding 5 credits in self-study mode at most once during the program, provided he/she has failed in it earlier and the course is not being offered as a regular course during that semester. Students should apply for a self-study course with appropriate recommendation of the Course Coordinator and the Head of the Department of the student s programme. The final sanction of a self-study course to a student is made by the Dean. Grant of a course to be taken as a self-study course cannot be claimed by any student as a matter of right. Normally, no formal lectures will be held for a self-study course but laboratory, design and computation exercises will be conducted if they form an integral part of the course. The Course Coordinator will hold minor and major tests besides other tests/quizzes for giving his/her assessment at the end of the semester. In summer semester, there will be at least one mid semester test and a major test. The self-study course will run during the total duration of the semester. The grades after due moderation by the Moderation Committee will be sent by the Department to Academic council at the end of the semester along with grades of all other courses. Colloquium will not be offered as a self-study course. 6.4 Summer Semester In the summer semester, registration for L (lecture) and P (practical) category courses will be strictly limited to the students who have obtained an E grade in the subject earlier. In a summer semester, a student cannot earn more than 12 credits (in all the categories).a summer course will run only if there is a minimum registration of 5 students. 7 POSTGRADUATE DEGREE REQUIREMENTS, REGULATIONS AND PROCEDURES 7.1 M.Tech (Full Time/ Part Time) DURATION FOR THE PROGRAMME Postgraduate programs leading to M. Tech. degree shall be of duration of 2 years spread over four Semesters for full-time students and 3 years spread over six semester for part-time students and each semester will normally have a duration of 75 net working days ELIGIBILITY FOR ADMISSIONS Candidate for admission to the M. Tech. degree programmes should have passed the final examination of the 4 year (or 8 semester) B. E. or B.Tech. degree programme of an appropriate branch of study or an examination accepted as equivalent thereto. 7.2 M. TECH. (FULL-TIME & PART-TIME) PROGRAMME 24 P a g e

25 Table No. 10 M.TECH. COURSE DISCIPLINES WITH ELIGIBILITY S.No. Department S.No. Specialization Degree/Qualifying Discipline 1 Civil 1 Structure 2 Transportation B.E./B.Tech./AMIE or equivalent in Civil 2 Computer Science & 1 Computer Science & (i). B.E./B.Tech./AMIE or equivalent in any engineering discipline. (ii). M.Sc. or equivalent in any science discipline. (iii). MCA 3 Electrical 1 Power System (i). B.E./B.Tech./AMIE or equivalent in Electronics & Communication/Telecommunication /Electrical / Instrumentation 1 Thermal B.E./B.Tech./AMIE or equivalent in Aeronautical / Aerospace / Automobile / Chemical / Mechanical 4 Mechanical 2 Industrial & Operations Research B.E./B.Tech./AMIE or equivalent in any discipline 3 Renewable Energy Technology (i) B.E./B.Tech./AMIE or equivalent in any discipline (ii). M.Sc. or equivalent in any science discipline. 5 Electronics & Communication 1 Digital Communication B.E./B.Tech./AMIE or equivalent in Electronics & Communication/Telecommunication 2 Integrated Electronics and Circuits /Electrical / Instrumentation 7.3 ACADEMIC PERFORMANCE REQUIREMENTS a) The minimum CGPA requirement for continuing in M. Tech. programme is 5.5. b) In the first semester in which the student registers, the minimum CGPA (SGPA) may be relaxed giving reasons to 5.0 by the SPGB on case to case basis. c) If a M. Tech. student secures a CGPA between 5.0 and 5.5 she/he may be allowed to continue in the next semester on the recommendation of the DPGC and with the approval of the University Chancellor. d) A student shall not be allowed to continue in the M. Tech. programme if i. His/her CGPA is below 5.0 ii. His/her CGPA is below 5.5 in two consecutive semesters. 7.4 EXAMINATION SCHEME 25 P a g e The distribution of marks for a course is divided into two parts. One is semester continuous assessment examinations and another is end term examination that is as follows:

26 Table-11Distribution of % Weight-age of marks for a Course A. Semester Continuous Assessment Examinations Particulars of Course Theory Theory + Lab. Lab. Only 1 Assignments/Tutorials/Class Performance/Quizzes/ Term Project 20% 15% 20% Total Weight-age of A 20% 30% 20% B. End Term Examinations 1 End Term Exam 80% 50% 2 Practical End Term Exam Lab experiment/ Procedure writing/ Tabulation/ Innovation etc. as applicable and Viva- Voce 20% 80% Total Weight-age of B 80% 70% 80% 7.5 THESIS EXAMINATION a) APPOINTMENT OF THESIS SUPERVISORS OF M. TECH. i. A student shall not normally have more than two supervisors at any given time. One of the supervisors shall always be from the department wherein the student has registered for his/her degree. ii. M.Tech. Thesis supervisor(s) of a student will normally be appointed from amongst the faculty members at Career Point University using modalities decided by the departments. iii. In case there has been a change/addition in the supervisor(s), the M.Tech. thesis will not be submitted earlier than six months from the date of such change. 7.6 M TECH THESIS ORAL EXAMINATION COMMITTEE i. The thesis will be examined by an oral examination committee formed by the thesis supervisor(s) in consultation with the DPGC Convenor and approved by University Chancellor. ii. The committee shall consist of the thesis supervisor(s), one faculty members from the department and one of the faculty members from the other department. One expert from outside the institute may be invited if so desired by the supervisor. The thesis supervisor will act as the Convener of the Committee. 7.7 M. TECH. THESIS After the M. Tech. oral examination committee has been constituted, unbound copies, of the thesis/project report one for each examiner of the oral board (as per the prescribed format) are to be submitted to chairperson, DPGC at least two weeks before the probable date of oral examination. The DPGC shall arrange to send the copies of the thesis to the examiners. Two copies of the abstract (approximately 200 words) should also be submitted along with the thesis. After the final viva voce Examinations the modifications suggested if any, by the thesis board, may be incorporated and then printed and electronic version on CD/DVD/equivalent media (preferably PDF) be submitted to the department (one copy for department and copy for onwards transmission to central library, by Convener DPGC). 7.8 M TECH. ORAL EXAMINATION 26 P a g e i. The oral examination will be conducted within two months from the date of submission of the thesis. ii. The thesis supervisor in coordination with DPGC will intimate the date of the oral examination to the Academic Section. iii. The oral examination committee will evaluate the thesis, conduct the oral examination and send a report of the examination to the Dean A through the Convener, DPGC. iv. A thesis will be considered to have been accepted if majority of members of the oral examination committee recommend its acceptance. A thesis, which is not accepted, will be considered to have been rejected. v. If a thesis is rejected along with a recommendation for resubmission after incorporating any modification/correction suggested by the oral examination committee, oral examination of the resubmitted thesis will be conducted by the original committee. However if any member of the previous vi. board has retired/left the institution/debarred by the senate/is on long leave or travelling then revised committee will be constituted with the approval of the University Chancellor. If the re-submitted thesis is rejected, the matter will be reported to the Senate for appropriate action.

27 vii. Acceptance of thesis will be reported to the Senate for approval. viii. If a student does not appear in the oral examination within this time period, his/her programme would be deemed to have been terminated. Request for reinstatement in the programme by such a student should be addressed to the University Chancellor. The request may be considered by the Chancellor on case to case basis. In case student does not appear second time the thesis submitted shall be deemed to be rejected. 7.9 M.Tech Degree Requirements The detailed degree requirements for M.B.A. and M.Tech. are listed in Table 12. Table 12: Continuation of Registration and Graduation Requirements for Postgraduate Programmes Degree Registration limits (Per semester) Criteria for continuation of registration Graduation Requirements Valid Credits Minimum DGPA Max. Period of Stay M.Tech (Regular) Minimum 12 credits and maximum 22 credits with the condition that no. of lecture courses to be not more than 6 60 (For some M.Tech Program requirement may be more than 60) semesters M.Tech (Part Time) Minimum one course and/or minor/major project. 12 credits with the condition that no. of lecture courses to be not more than 3 60 (For some M.Tech Program requirement may be more than 60) semesters MBA (Regular) Same as M.Tech regular compulsory audit courses Continuation Requirements The detailed requirements for continuation as a student in the respective programme for M.B.A. andm.tech. degrees are listed in Table 12. Failure to maintain the specified academic standing will result in termination of registration and the student s name will be struck-off the rolls. The maximum permitted duration of each programme will be determined in terms of number of registered regular semesters, hereinafter called registered semesters. Any semester in which a student has registered for a course will be called a registered semester subject to the following: a. Only the 1 st and 2 nd semesters of an academic year can be registered semesters. The summer semester will not be considered as a registered semester. b. A semester when a student has been granted semester withdrawal or granted leave will not be considered as a registered semester. c. The semester when a student is suspended from the Institute on disciplinary grounds will not be counted towards the number of registered semesters. The summer semesters falling in between the permitted registered semesters shall be available for earning credits. After the student has registered for the maximum permissible number of registered semesters, the subsequent summer semesters will not be available for earning credits. 8 Lower And Upper Limits For Credits Registered For full-time students pursuing M.B.A. and M.Tech. the minimum registration requirement in a semester is 12 credits, and for part-time students, the minimum registration requirement is 3 credits. These minimum credit requirements are not applicable for graduating students who require lower than the proposed minimum to graduate. 8.1 Audit Requirement 27 P a g e a. A student can request for an audit grade in any course provided he/she is eligible to earn audit credits, he/ she is already registered for that course and it is not a core requirement of the student s programme. The request for auditing a course should be made on or before the last date for audit requests as defined in the semester schedule. b. M.Tech. students are eligible for auditing a course at any time before completion of the programme. c. A student earn either a NP (audit pass) or a NF (audit fail) grade for an audit course. The audit pass (NP) grade may be awarded if the student satisfies the attendance criteria specified for the course and he/she has obtained at least a D grade. The course coordinator can specify a higher criterion for audit pass at thebeginning of the semester. If either of these requirements is not fulfilled, the audit fail (NF) grade is awarded. d. Grades obtained in an audit course are not considered in the calculation of SGPA or CGPA.

28 e. All students (B.Tech., Dual-Degree, Integrated M.Tech.) can earn a maximum of 8 credits from elective course as audit, in any category out of total credits required for graduation. f. M.Tech. students can audit a course over and above their core requirements, as specified by the supervisor. g. A student (UG/PG) is permitted to audit courses over and above their graduation requirement. h. Non-credit core courses or core courses not considered for calculation of SGPA or CGPA for PG programmes like MBA and M.Tech. should not be referred to as audit courses. 8.2 Summer Registration Summer semester registration for PG students is admissible. M.Tech. students will be allowed toregister for maximum of one course (up to 4 credits) and M.B.A. students up to 2 courses in the summer if andonly if that is the only requirement for completion of the degree and is recommended by Academic council. For projects, incase X or I grade is awarded in the second semester, the student would be expected to register during summer forcompletion of the project. Normally regular courses would not be offered during summer semester. Courses can be offered by departments for taking care of special situations subject to the availability of faculty. 28 P a g e

29 9 The overall credits structure: B.Tech. [Civil] The overall credits structure OC 10 EAS 17 DE 27 HU/HM 21 DC 66 BS 19 TOTAL 160 LIST OF DEPARTMENTAL CORE IN CIVIL ENGINEERING S NO CODE SUBJECT L T P CREDIT 1 CEC 210 Colloquium CED 411 Major project part P a g e CEL 212 Environmental Engg CEL 222 Engg Geology & soil Mechanics CEL 231 Structural Analysis CEL 232 Concrete Material & design CEL 241 Transportation engg CEL 251 Hydrology & hydraulics CEL 271 Elements of Surveying CEL 321 Geotechnical engg CEL 331 Structural Analysis -II CEL 332 Design of steel structure CEL 351 Design of hydraulic structure CEL 339 Concrete Technology & material AML 170 Fluid Mechanics LIST OF DEPARTMENTAL ELECTIVE IN CIVIL ENGINEERING S NO CODE SUBJECT L T P CREDIT 1 CEL 311 Advance water & waste water engg CEL 341 Transportation engg -II CEL 362 Construction management CEL 411 Industrial waste management CEL 412 Environmental Assessment Methodologies CEL 421 Ground improvement technology CEL 422 Rock engg CEL 423 Design of foundation, earth & earth retaining Structure CEL 431 Advance Structure analysis CEL 432 Design of prestressed concrete & industrial Structure CEL 433 Advanced Structural Design CEL 442 Traffic & transportation planning CEL 443 Transportation safety & environment CEL 451 Water power engg CEL 453 Water resources Management CEL 455 Introduction to geographic information system CEL 459 River Mechanics

30 18 CEL 464 Construction contract & economics CEL 466 Construction equipment & methods CEP 452 Computational aspects in water resources CED 412 Major project part -II P a g e

31 LIST OF OPEN COURSES IN CIVIL (CIVIL ENVIRONMENTAL ENGINEERING) S.NO. OC NO. SEM. Sub. Code Name of Subject Credit Total Credit 1 OC-1. IV CEL110 BASIC CONCEPTS IN SUSTAINABLE DEVELOPMENT OC-2. V CEL 295 ECOLOGY AND ECOSYSTEM DYNAMICS OC-3. V CEL 412 ENVIRONMENTAL ASSESSMENT METHODOLOGIES OC-4. VI CEL 120 POLLUTION PREVENTION AND CONTROL OC-5 VI CEL 100 EARTH AND EARTH PROCESSES OC-6 VII CEL 140 ENVIRONMENTAL STUDIES OC-7 VII CEL326 GEOENVIRONMENTAL ENGINEERING OC-8 VIII CEL 411 INDUSTRIAL WASTE MANAGEMENT OC-9 VIII CEL422 ROCK ENGINEERING P a g e

32 Sem. LC L T P WC CR. I II III IV V VI VII VIII AML110 Mechanics (3-0-2) 4 MEL 120 Manufacturing Practice (2-0-3) 3.5 CEL 231 Structural Analysis - I (3-0-2)4 CEL 212 Environmental Engg (3-0-2)4 CEL 321 Geotechnical Engg (3-1-3)5.5 CEL 332 Design of Steel Structures (3-1- 2) 5 CET -410 Practical Training CEC 410 Colloquium (0-3-0)3 CED 412 Major Project Part -2 (0-0-16) 8 CSL101 Introduction to Computers & Programming (3-0-2) 4 EEL 101 Fundamentals of Electrical (3-0-2) 4 CEL 241 Transportation Engg-1(3-0-2)4 Mathematics (3-1-0)4 CEL 331 Structural Analysis -II(3-1- 2)5 CED 411 Major Project part 1(0-0-8)4 CYL110 Chemistry: Concepts and Applications PHL 110 Fields and Waves (3-1- 0) 4 AML 170 Fluid Mechanics (3-0-2) 4 CEL 222 Engg Geology & soil mechanics (3-1-3)5.5 DE-1 CEL 341Transportation Engg-II (3-1-0)4 CEL 232 Concrete material & design (3-1- 4)6 CEL 351 Design of hydraulic structures (2-0-2) 3 CYP100 Chemistry Laboratory (0-0-4) 2 PHP 100 Physics Lab (0-0-3) 1.5 CEL 271 Elements of surveying (2-0-2)3 CEL251 Hydrology & Hydraulics (3-1- 4)6 DE-2 CEL 311 Advanced water & wastewater engg (3-0-2) 4 DE-3 CEL 466 Construction Equipments & Methods (2-1-0) 3 MAL110 Mathematics I MAL120 Mathematics I MEL110 Graphics Science (0-0-3) 1.5 CEL 339 Concrete technology & Materials (3-0-0)3 OC-2 (3-0-0)3 DE-4 CEL 423 Design of foundations, Earth & Earth retaining structures (3-1-0)4 DE-5 CEL 453 Water Resources Management (3-1-0)4 OC1 (3-1-0)4 OC-3 (3-0-0)3 HUL 101 English in Practice-I (2-0-2) 3 HUL 110 Communication Skills (2-0-2) 3 HUL235 English (Technical Communication) (2-1-0) 3 HUL234 Language & Communication HUL242 Soft Skills & Personality Development HUL300 Hu & So Sc. #2 (3-1- 0) P a g e

33 10 The overall credits structure: B.Tech. [CSE] The overall credits structure OC 10 EAS 17 DE 47 HU & HM 21 DC 58 BS 20 TOTAL 174 Departmental Core S.NO. CODE COURSE TITLE L T P CR. 1 CSL 105 Discrete Mathematical Structures CSL 201 Data Structures CSL 211 Computer Architecture EEL 201 Digital Electronics EEP 201 Electronics Lab CSP 301 Design Pract. in Comp. Sc CSL 307 Programming Language MAL 250 Introduction to Probability Theory and Stochastic Processes CSL375 Operating Systems CSL356 Analysis and Design of Algorithms CSL374 Computer Networks CSL434 Programming in Java CSC410 Colloquium (CS) CSD411 Major Project Part-1 (CS) CSL312 Programming in C Departmental Elective S.NO. CODE COURSE TITLE L T P CR. 1 CSL 332 Introduction to Database Systems CSL781 Computer Graphics CSL705 Theory of Computation CSL333 Artificial Intelligence CSL728 Compiler Design CSL740 Software CSL759 Cryptography and Computer Security CSD412 Major Project Part 2 (CS) CSL718 Architecture of High Performance Computer Systems CSL834 Data compression Technique CSL765 Introduction to Logical & Functional Programming CSL837 Mobile Computing P a g e

34 13 CSL838 Wireless Networks CSL837 Mobile Adhoc Networks CSL839 Cloud Computing CSL835 Data Mining & Warehousing CSL633 Resource Management in Computer Systems CSL830 Distributed Computing CSL841 Cluster & Grid computing CSL724 Advance Computer Networks CSL758 Advance algorithms CSL847 Distributed Algorithms CSL851 Algorithmic Graph Theory CSL840 Computer Vision CSL868 Special topic in Database Systems CSL862 Special topic in software Systems CSL812 System Level Design and Modeling(Embedded System) CSL555 Microprocessor and Interfaces Advanced Data Structures CSD412 Major Project (CS) Minor Degree-I in Computer Science & OR Software Core Courses S.NO. CODE COURSE TITLE L T P CR. 1 CSL 201 Data Structures CSL 211 Computer Architecture Elective Courses S.NO. CODE COURSE TITLE L T P CR. 1 CSL311 Object Oriented Programming CSL 332 Introduction to Database Systems CSL356 Analysis and Design of Algorithms CSL375 Operating Systems CSL333 Artificial Intelligence CSL740 Software SML853 Software Project Management Minor Degree-II in Mobile Computing Core courses S.NO. CODE COURSE TITLE L T P CR. 1 CSL830 Distributed Computing CSL374 Computer Networks P a g e

35 Elective courses S.NO. CODE COURSE TITLE L T P CR. 1 CSL837 Mobile Computing CSL838 Wireless Networks CSL837 Mobile Adhoc Networks CSL839 Cloud Computing Internet Security CSL759 Cryptography and Computer Security CSL841 Cluster & Grid computing P a g e

36 Sem. Subjects LC L T P WC CR. I AML110 Mechanics (3-0-2) 4 CSL101 Introduction to Computers & Programming (3-0-2) 4 CYL110 Chemistry: Concepts & Applications CYP100 Chemistry Laboratory (0-0-4) 2 MAL110 Mathematics I HUL 101 English in Practice-I (2-0-2) II MEL 120 Manufacturing Practice (2-0-3) 3.5 EEL 101 Fundamentals of Electrical (3-0-2) 4 PHL 110 Fields and Waves PHP 100 Physics Lab (0-0-4) 2 MAL120 Mathematics I MEL110 Graphics Science (0-0-3) 1.5 HUL 110 Communication Skills (2-0-2) III CSL 105 Discrete Math. Str. (3-1-0)4 CSL 201 Data Structures (3-0-4)5 CSL 211 Computer Architecture (3-1-2)5 CSL312 Programming in C++ (3-0-2)4 EEL 201 Digital Electronics (3-1-0)4 EEP 201 Electronics Lab-1 (0-0-3)1.5 HUL235 English (Technical Communication) (2-1-0) IV V VI CSL307 Programming Language (3-0-0)3 CSL356 Analysis & Design of Algorithms (3-0-2)4 CSL374 Computer Networks (3-0-3)4.5 MAL 250 Prob. Stoch Proc (3-1-0)4 (DE-3) CSL705 Theory of Computation (3-1-0)4 CSL434 Programming in Java (3-0-2)4 (DE-1) CSL 332 Intro to DBMS (3-0-3)4.5 CSL555 Microprocessor and Interfaces(3-1-2) 5 CSL375 Operating Systems (3-0-3)4.5 (DE-5) CSL781 Computer Graphics (3-0-3) 4.5 (DE-4) CSL740 Software (3-0-2)4 OC-2 (3-1-0)4 OC1 (3-0-0)3 OC-3 (3-0-0)3 CSL830 Distributed Computing (3-0-0)3 HUL234 Language & Communication HUL242 Soft Skills & Personality Development HUL300 Communication Skills & Personality Development CST -410 Practical Training VII CSC410 Colloquium (CS) (0-3-0)3 (DE-6) CSL728 Compiler Design (3-0-3)4.5 (DE-8) CSL333 Artificial Intelligence (3-1-0)4 CSD411 Major Project Part-1 (CS) (0-0-8)4 CSL837 Mobile Computing (3-0-0) VIII CSD412 Major Project Part-2 (CS) (0-0-16) 8 (DE-7) CSL759 Cryptography and Computer Security (3-0-0)3 CSL835 Data Mining & Warehousing (3-1-0) P a g e

37 11 The overall credits structure: B.Tech. [EE] The overall credits structure Undergraduate Core (UC) Undergraduate Elective (UE) Category Credits Category Credits DC 67.5 DE 28.5 BS 19 HU & HM 21 EAS 17 OC 10 Total Total 55.5 Total Credits 159 Basic Sciences (BS) Core Code Subject Name L T P Total CYL110 Chemistry: Concepts and Applications CYP100 Chemistry Laboratory MAL110 Mathematics I MAL120 Mathematics II PHL110 Field & Waves PHP100 Physics Laboratory Arts and Sciences (EAS) Core Code Subject Name L T P Total AML110 Mechanics CSL101 Introduction to Computers & Programming EEL101 Fundamentals of Electrical MEL110 Graphic Science MEL120 Manufacturing Practices Humanities and Social Sciences (HC) Core Code Subject Name L T P Total HUL 101 English in Practice-I HUL110 Communication Skills HUL235 English (Technical Communication) HUL234 Language & Communication HUL242 Soft Skills & Personality Development HUL300 Communication Skills & Personality Development Subject Credits S No Code Name Category L T P TOTAL 1 CSL201 Data Structures DC P a g e

38 2 EEC420 Colloquium (EE) DC EED421 Major Project Part 1 (EE) DC EEL201 Digital Electronic Circuits DC EEL202 Circuit Theory DC EEL203 Electromechanics DC EEL204 Analog Electronics Circuits DC EEL205 Signals and Systems DC EEL209 Power Electronics Devices and Circuits DC EEL301 Control - I DC EEL303 Power - I DC EEL305 Electric Drives DC EEL308 Computer Architecture DC EEP201 Electronics Laboratory - I DC EEP203 Electromechanics Laboratory DC EEP204 Electronics Laboratory - II DC EEP209 Power Electronics Laboratory DC EEP301 Control Laboratory DC EEP303 Power Laboratory DC EEP305 Drives Laboratory DC EEP308 Computer Technology Laboratory DC EET420 Practical Training (EE) DC MAL 250 Probability Theory and Stochastic DC S No Subject Credits Code Name Category L T P TOTAL 1 EED422 Major Project Part 2 (EE) DE EEL306 Communication DE EEL325 Control II DE EEL451 Power Systems Protection DE EEP 451 Power Systems Protection Lab DE EEL452 HVDC Transmission DE EEL453 Power System Dynamics and Control DE EEL456 Power II DE EEL339 Power Conditioning DE EEL342 DSP based Control of Electric Drive DE EEL344 Electric Transportation DE EEL346 Electrical Machines and Industrial Drives DE EEL349 Advanced Electrical Machines DE EEL359 Electric Machine Design and CAD of Electric Machines DE EEL365 Intelligent Control DE EEL375 Embedded Systems DE EEL388 Stepper Motors DE P a g e

39 18 EEL389 Computer Aided Testing of Electric Machines DE EEL394 Permanent Magnet Motors DE EEL398 Machines and Drives Dynamics DE EEL404 Flexible AC Transmission System DE EEL405 Power Instrumentation DE EEL407 Distribution System Planning and Automation DE EEL423 Demand Side Management DE EEL424 Nuclear Power Generation DE EEL428 Substation Design DE EEL455 Power System Planning DE EEL458 Power Systems Optimization DE EEL482 Mechatronics DE EEL483 Hydro Power Generation DE EEL486 Illumination and Heating DE EEL487 Intelligent Algorithms for Power Systems DE EEL741 Modelling and Analysis of Electrical Machines DE EEL748 Power Quality DE EEL749 Special Electromechanical Systems DE EEL772 Optimal Control Theory DE Minor Degree-I in Power System S No Subject Credits Code Name L T P TOTAL 1 EEL210 Circuit Analysis EEL312 Electrical Machines EEL310 Control Theory EEL328 Control Theory II EEL332 Power System EEL459 Power System II EEL454 Protection of Power System EEL457 High Voltage AC/DC transmission EEL461 Dynamic Power System and Control Minor Degree-I in Power Electronics S No Subject Credits Code Name L T P TOTAL 1 EEL210 Circuit Analysis EEL214 Digital Electronic Theory EEL208 Electronic devices & Circuits EEL310 Control Theory EEL335 Power Electronics EEL328 Control Theory II P a g e

40 7 EEL425 Power System Instrumentation EEL419 Electrical Drives EEL454 Protection of Power System P a g e

41 Sem. LC L T P WC CR I II III IV V CYL 110 MAL110 AML110 CSL101 CYP 100 HUL101 Introduction to Chemistry: Chemistry English in Mathematics-I Computers and Concepts and Mechanics Laboratory Practice-I Programming Applications PHL 110 MAL 120 EEL 101 MEL 120 MEL110 PHP100 HUL110 Fundamentals of Fields and Manufacturing Physics Communication Mathematics-II Electrical Graphic Science Waves Practices Laboratory Skills EEL 201 EEL 202 EEL 203 EEL 205 EEP 201 EEP 203 HUL235 Digital Electronic Circuits Circuit Theory Electromechanics Signals and Systems Electronics Laboratory - I Electromechanics Laboratory English (Technical Communication) EEL 204 MAL250 EEL 301 EEP 204 EEP 301 HUL 234 Analog Probability Control Control Electronics Language and Electronics theory and - I Laboratory - II Communication Circuits stochastic Laboratory EEL 303 CSL 201 EEL 306 EEL 325 EEP 303 HUL 242 Power - I Data Structures Communication Control - II Power Laboratory Soft Skills & Personality Development OC-2 OC-1 OC VI VII VIII 41 P a g e EEL 209 EEL 308 EEP 308 EEL 456 EEP 209 HUL 300 Power Electronics Devices and Circuits Computer Architecture Computer Technology Laboratory Power - II Power Electronics lab Communication Skills & Personality Development EET 420 PRACTICAL TRAINING (EE) EEC 420 EED 421 EEL 305 EEL 451 EEP 305 EEP 451 Colloquium (EE) Major Project Part 1 (EE) Electric Drives Power Systems Protection Drives Lab Power Systems Protection Lab EEL 452 EEL 453 EED 422 HVDC Transmission Power System Dynamics and Control Major Project Part 2 (EE) OC-4 OC-6 OC-8 OC-5 OC-7 OC

42 12 The overall credits structure: B.Tech. [ECE] The overall credits structure Undergraduate Core (UC) Undergraduate Elective (UE) Category Credits Category Credits DC 62.5 DE 37 BS 19 HU & HM 17 EAS 17 OC 10 Total 98.5 Total 64 Total Credits Basic Sciences (BS) Core Code Subject Name L T P Total CYL110 Chemistry: Concepts and Applications CYP100 Chemistry Laboratory MAL110 Mathematics I MAL120 Mathematics II PHL110 Field & Waves PHP100 Physics Laboratory Arts and Sciences (EAS) Core Code Subject Name L T P Total AML110 Mechanics CSL101 Introduction to Computers & Programming EEL101 Fundamentals of Electrical MEL110 Graphic Science MEL120 Manufacturing Practices Humanities and Social Sciences (HC) Core Code Subject Name L T P Total HUL 101 English in Practice-I HUL110 Communication Skills HUL235 English (Technical Communication) HUL234 Language & Communication HUL242 Soft Skills & Personality Development HUL300 Communication Skills & Personality Development S No Subject Credits Code Name Category L T P TOTAL 42 P a g e

43 1 EEL205 Signals and Systems DC EEL202 Circuit Theory DC EEL201 Digital Electronic Circuits DC EEP201 Electronics Lab-I DC EEL204 Analog Electronics Circuits DC EEL301 Control Engg-1 DC EEP204 Electronics Lab-II DC MAL250 Prob Soch proc. DC EEP301 Control Engg lab DC EEL207 Engg Electromagnetics DC EEP307 Electromagnetics Lab DC EEL306 Comm. Engg. DC EEP306 Comm. Engg Laboratory DC EEL441 Industrial Electronics DC EEL318 Microprocessor DC EEL322 Integrated Circuits Technology DC EEL329 VLSI Technology and Design DC EEL338 Antennas and Propagation DC EED421 Major Project Part-I DC EEP205 Signal Processing Lab-1 DC EEL334 Wireless Communication DC EET420 Pratical Training(ECE) DC S No Subject Credits Code Name Category L T P TOTAL 1 CSL201 Data structures DE EEL308 Computer Architecture DE EEL358 Operating Systems DE EEL321 Digital Hardware Designs DE EEL442 OP-Amps and Linear Integrated circuits DE EEL316 Digital Comm. DE EEL713 Microwave Theory and Circuits DE EEL319 Digital Signal Processing DE EEC420 Colloquium (ECE) DE EED412 Major Project Part 2 (ECE) DE List of Open Core for Minor Degree (Communication ) Subject Credits S No Code Name L T P TOTAL 1 EEL208 Electronic devices & Circuits EEL313 Signals System P a g e

44 3 EEL314 Communication Theory EEL333 Communication Theory-II EEL336 Advanced Signal Processing EEL434 Optical Communication EEL474 Antenna Fundamentals EEL436 Mobile Communication EEL471 Telecommunication and Switching Networks List of Open Core for Minor Degree( Integrated Electronics &Circuits ) Subject Credits S No Code Name L T P TOTAL 1 EEL208 Electronic devices & Circuits EEL343 Integrated Circuits EEL345 Digital System Design EEL347 CMOS VLSI Design EEL336 Advanced Signal Processing EEL439 Operational Amplifier EEL429 Microelectronic Circuits EEL476 Analog Mixed Signal Ics EEL475 Telecommunication and Switching Networks P a g e

45 Sem. L L T P WC CR C I CYL 110 MAL110 AML110 CSL101 CYP 100 HUL Chemistry: Concepts and Applications Mathematics-I Mechanics Introduction to Computers and Programming Chemistry Laboratory English in Practice-I II PHL 110 MAL 120 EEL 101 MEL 120 MEL110 PHP100 HUL Fields and Mathematics-II Fundamentals Manufacturing Graphic Science Physics Communication Waves of Electrical Practices Laboratory Skills III EEL 201 EEL 202 CSL 201 EEL 205 EEP 201 HUL Digital Electronic Circuit Theory Data Structure Signals and Electronics English Circuits Systems Laboratory - I (Technical Communication) IV EEL 204 MAL 250 EEL 301 EEP 204 EEP 301 EEL 207 HUL 234 EEP Analog Electronics Circuits Probability theory and stochastic Control - I Electronics Laboratory - II Control Laboratory Electromagnetics Language and Communication Electromagnetics Lab OC V EEL 306 EEL 321 EEL 308 EEL 442 EEP 306 EEP 205 HUL Communication Digital Hardware Computer Signal Processing OC-2 OC-3 1 Design Architecture Laboratory-I OP-AMPS & Linear Integrated Circuits Communication Laboratory Soft Skills & Personality Development VI EEL441 EEL 318 EEL 316 EEL 713 HUL Industrial Microprocessor Digital Microwave Communication OC-4 OC-5 Electronics Communicatio Theory & Circuits Skills & Personality Development ECT 420 PRACTICAL TRAINING (EP) VII EEL 338 EED 421 EEL 319 EEC Antennas & Major Project Digital Signal Colloquium(ECE) OC-6 OC-7 Propagation Part 1 (ECE) Processing P a g e

46 VIII EEL 329 EEL 334 EED VLSI Technology & Design Wireless Communication Major Project Part 2 (ECE) OC-8 OC P a g e

47 13 The overall credits structure: B.Tech. [Mechanical] The overall credits structure OC 10 EAS 18 DE 31 HU & HM 21 DC 75 BS 19 TOTAL 174 Basic Sciences (BS) Core L T P Total CYL110 Chemistry: Concepts and Applications CYP100 Chemistry Laboratory MAL110 Mathematics I MAL120 Mathematics II PHL110 Field & Waves PHP100 Physics Laboratory Arts and Sciences (EAS) Core L T P Total AML110 Mechanics CSL101 Introduction to Computers & Programming EEL101 Fundamentals of Electrical MEL110 Graphic Science MEL120 Manufacturing Practices Humanities and Social Sciences (HC) Core L T P Total HUL 101 English in Practice-I HUL110 Communication Skills HUL235 English (Technical Communication) HUL234 Language & Communication HUL242 Soft Skills & Personality Development HUL300 Communication Skills & Personality Development List of Department core ( DC) Course Code Course Name L T P Credit MEL140 Thermodynamic AML160 Mechanics of Fluids MEL211 Kinematics and Dynamics of Machines AML140 Mechanics of Solids AMP261 Solids Laboratory AMP262 Fluids Laboratory MEP201 Mechanical Drawing P a g e

48 MEL241 Energy Conversion MEL236 Material Science MEL232 Casting, Welding and Forming MAL230 Numerical Methods MEL221 Operations Research MEL242 Heat and Mass Transfer MEL311 Machine Element Design MEL233 Machining, Machine Tools and Metrology MEL312 Mechanical Measurement, Control Theory & Applications MEP341 Thermal Laboratory MEL322 Operations Planning and Control MEL410 Practical Training MEC410 Colloquium MED411 Major Project Part MEL421 Production Management MEL425 Flexible Manufacturing Systems Departmental Electives (DE) Course Code Course Name L T P Credit MED310 Mini Project (ME) MEL310 Concurrent MEL314 Noise MEL316 Mechanical Vibrations MEL321 Ergonomics MEL332 Design and Manufacturing of Composites MEL333 Metrology MEL334 Low Cost Automation MEL341 Gas Dynamics and Propulsion MEL342 Power Plant Technologies MEL343 Fuels, Combustion and Pollution MEL344 Refrigeration and Air-Conditioning MEL345 Internal Combustion Engines MEL346 Turbo-machinery MEL410 Creativity in MEL411 Mechatronics MEL412 Advanced Mechanical Design MEL413 Design of Mechanisms MEL414 Computer Aided Mechanical Design MEL415 Vibrations Design MEL416 Robotics MEL417 Lubrication MEL420 Total Quality Management MEL422 Project Management MEL425 Flexible Manufacturing Systems MEL431 CNC Machines and Programming MEL432 Microprocessor Applications in Manufacturing MEL433 Micro- and Nano- Manufacturing MEL434 Design for Manufacturing and Assembly MEL435 Geometric Modelling for Manufacturing MEL436 Injection Moulding and Mould Design MEL441 Modelling and Experiments in Heat Transfer P a g e

49 MEL442 Thermal Analysis of Bio-systems MEL716 Nano Scale Heat Transfer MED412 Major Project Part 2 (ME) Minor Degree in Production and Industrial Course Code Course Name L T P Credit OE-1 MEL202 Quality & Management Systems OE-2 MEL221 Operations Research OE-3 MEL322 Operations Planning and Control OE-4 MEL325 Production -I OE-5 MEL339 Production -II OE-6 MEL422 Project Management OE-7 MEL425 Flexible Manufacturing Systems OE-8 MEL411 Mechatronics OE-9 MEL418 Reliability & Maintenance OE-10 MEL427 Manufacturing Economics and Analysis P a g e

50 Sem. LC L T P WC CR. I II III IV V VI VII VIII 50 P a g e AML110 Mechanics (3-0-2) 4 MEL 120 Manufacturing Practice (2-0-4) 4 MEL 140 Thermodynamics MEL236 Material Science MEL242 Heat and Mass Transfer MEL312 Mechanical Measurement, Control Theory & Applications (3-1-2) 5 DE-3 MEL342 Power Plant Technologies DE-5 MEL316 Mechanical CSL101 Introduction to Computers & Programming (3-0-2) 4 EEL 101 Fundamentals of Electrical (3-0-2) 4 AML160 Mechanics of Fluids MEL232 Casting, Welding and Forming (3-0-2) 4 MEL311 Machine Element Design (3-1-2) 5 MEP341 Thermal Laboratory (0-0-3) 1.5 DE-4 MEL425 Flexible Manufacturing Systems (3-0-0) 3 DE-6 MEL420 Total Quality CYL110 Chemistry: Concepts and Applications PHL 110 Fields and Waves MEL 211 Kinematics and Dynamics of Machines (3-0-2) 4 MAL230 Numerical Methods MEL233 Machining, Machine Tools and Metrology (3-0-2) 4 DE-1 MEL344 Refrigeration & Air Conditioning MEC410 Colloquium (ME) (0-3-0) 3 DE- 7 MED412 Major Project CYP100 Chemistry Laboratory (0-0-4) 2 PHP 100 Physics Lab (0-0-3) 1.5 AML140 Mechanics of Solids MEL221 Operations Research (3-1-0) MEL241 Energy Conversion MEL322 Operations Planning and Control (3-0-0) MED411 Major Project Part 1 (ME) (0-0-8) 4 MAL110 Mathematics I MAL120 Mathematics I AMP262 Fluids Laboratory (0-0-3) 1.5 MEP 201 Mechanical Drawing (1-0-3) 2.5 OC-2 (3-0-0) 3 DE-2 (MEL345) Internal Combustion Engine MET410 Practical Training (ME) MEL421 Production Management (3-1-0) 3 ENV101 Environmental Studies (0-0-0) 0 MEL110 Graphics Science (0-0-3) 1.5 AMP261 Solids Laboratory (0-0-3) 1.5 OC-1 (3-0-0) 3 OC-3 HUL 101 English in Practice-I (2-0-2) 3 HUL 110 Communication Skills (2-0-2) 3 HUL235 English (Technical Communication) (2-1-0) 3 HUL234 Language & Communication HUL242 Soft Skills & Personality Development HUL300 Communication Skills & Personality Development

51 Vibrations (3-0-2) 4 Management Part 2 (0-0-16) 8 51 P a g e

52 14 The overall credits structure: B.Tech.+M.Tech. [Civil] The overall credits structure OC 10 EAS 17 DE 19 HU/HM 21 DC 62 PE 21 BS 19 PC 36 TOTAL 205 LIST OF DEPARTMENTAL CORE IN CIVIL ENGINEERING S NO CODE SUBJECT L T P CREDIT 1 CEC 210 Colloquium CED 411 Major project part CEL 212 Environmental Engg CEL 222 Engg Geology & soil Mechanics CEL 231 Structural Analysis CEL 232 Concrete Material & design CEL 241 Transportation engg CEL 251 Hydraulogy & hydraulics CEL 271 Elements of Surveying CEL 321 Geotechnical engg CEL 331 Structural Analysis -II CEL 332 Design of steel structure CEL 351 Design of hydraulic structure CEL 339 Concrete Technology & material AML 170 Fluid Mechanics LIST OF DEPARTMENTAL ELECTIVE IN CIVIL ENGINEERING S NO CODE SUBJECT L T P CREDIT 1 CEL 311 Advance water & waste water engg CEL 341 Transportation engg -II CEL 362 Construction management CEL 411 Industrial waste management CEL 412 Environmental Assessment Methodologies CEL 421 Ground improvement technology CEL 422 Rock engg CEL 423 Design of foundation, earth & earth retaining Structure CEL 431 Advance Structure analysis CEL 432 Design of prestressed concrete & industrial Structure CEL 433 Advanced Structural Design CEL 442 Traffic & transportation planning CEL 443 Transportation safety & environment CEL 451 Water power engg CEL 453 Water resources Management P a g e

53 16 CEL 455 Introduction to geographic information system CEL 459 River Mechanics CEL 464 Construction contract & economics CEL 466 Construction equipment & methods CEP 452 Computational aspects in water resources CED 412 Major project part -II S. No OC No. Sem 1 LIST OF OPEN COURSES IN CIVIL(CIVIL ENVIRONMENTAL ENGINEERING) Subject Code Name of Subject Credit OC-1. IV CEL110 BASIC CONCEPTS IN SUSTAINABLE DEVELOPMENT Total Credit OC-2. V CEL 295 ECOLOGY AND ECOSYSTEM DYNAMICS OC-3. V CEL 412 ENVIRONMENTAL ASSESSMENT METHODOLOGIES OC-4. VI CEL 120 POLLUTION PREVENTION AND CONTROL OC-5 VI CEL 100 EARTH AND EARTH PROCESSES OC-6 VII CEL 140 ENVIRONMENTAL STUDIES OC-7 VII CEL326 GEOENVIRONMENTAL ENGINEERING OC-8 VIII CEL 411 INDUSTRIAL WASTE MANAGEMENT OC-9 VIII CEL422 ROCK ENGINEERING Course Code List of Program Electives Course Title L T P Credit CEL610 Foundation CEL612 CEL614 CEL707 Construction Methods in Geotechnical Geoenvironmental and Geohazards Soil Dynamics and Geotechnical Earthquake CEL709 Offshore Geotechnical CEL712 Landfills and Ash Ponds CEL714 Special Topics in Geotechnical and Geoenvironmental P a g e

54 CEL715 Soil Structure Interaction Analysis CEL760 Finite Element Method in Geotechnical CES810 Independent Study (CEG) CEL610 Foundation CEL612 CEL614 CEL707 Construction Methods in Geotechnical Geoenvironmental and Geohazards Soil Dynamics and Geotechnical Earthquake CEL709 Offshore Geotechnical List of Program Core Course Code Course Title L T P Credit CED701 Minor Project (CEG) CED811 Major Project Part 1 (CEG) CED812 Major Project Part 2 ( CEG) CEL701 Behavior of Soils CEL702 Slope Stability and Earth Dams Site Investigations and Ground CEL703 Improvement CEL704 Shallow and Deep Foundations CEL705 Geoenvironmental CEL706 Geosynthetics CEL708 Earth Pressures and Retaining Structures CEP701 Soil Laboratory Geoenvironmental and Geotechnical CEP702 Laboratory P a g e

55 Sem. Subjects LC L T P WC CR. I II III AML110 Mechanics (3-0-2) 4 MEL 120 Manufacturing Practice (2-0- 3) 3.5 CEL 231 Structural Analysis - I (3-1-2)5 CSL101 CYL110 Introduction to Computers Chemistry: & Programming Concepts and App. (3-0-2) 4 EEL 101 Electrical (3-0-2) 4 CEL 241 Transportation Engg-1(3-0-2)4 PHL 110 Fields and Waves AML 170 Fluid Mechanics (3-0-2) 4 CYP100 Chemistry Laboratory (0-0-4) 2 PHP 100 Physics Lab (0-0-3) 1.5 CEL 271 Elements of surveying (2-0-2)3 MAL120 Mathematics I MAL110 Mathematics I MEL110 Graphics Science (0-0-3) 1.5 CEL 339 Concrete technology & Materials(3-0-0)3 HUL 101 English in Practice-I (2-0-2) 3 HUL 110 Communication Skills (2-0-2) 3 HUL 235 English (Technical Communication ) (2-1-0) IV V CEL 212 Environmental Engg(3-0-2)4 CEL 321 Geotechnical Engg (3-1- 3)5.5 Math- (3-1-0)4 CEL 331 Structural Analysis -II(3-1-2)5 CEL 222 Engg Geology & soil mechanics (3-1-3)5.5 DE-1 CEL 341Transportation Engg-II (3-1-0)4 CEL251 Hydrology & Hydraulics (3-1-4)6 DE-2 CEL 311 Advanced water & wastewater engg (3-0-2) 4 OC 1 (3-1-0)4 OC-2 (3-0-0)3 OC-3 (3-0-0)3 HUL234 Language & Communication HUL242 Soft Skills & Personality Development VI CEL 332 Design of Steel Structure (3-1-2) 5 CEL 232 Concrete material & design (3-1-4)6 DE-3 CEL 466 Construction Equipment & Methods (2-1-0) 3 HUL300 Hu & So Sc. #2 (3-1- 0) C ET -410 Practical Training VII VIII CEC 410 Colloquium (0-3-0)3 DE CED310 Mini Project (CE) (0-0-6)3 CEL 351 Design of hydraulic structures (2-0-2) 3 DE-5 CEL 453 Water Resources DE-4 CEL 423 Design of foundations, Earth & Earth retaining structures (3-1-0)4 PE-1 CEL 612 Construction Methods in Geotechnical PC-1 CEL 701 Behaviour of Soils (3-0-0)3 DE-6 CEL 432 Design of Prestressed Concrete and Industrial PC -4 CEL 708 Earth Pressures and Retaining PC -2 CEL 703 Site Investigations and Ground Improvement (3-0-0)3 PC -5 CEL 704 Shallow and Deep PC -3 CEL 705 Geoenvironmental (3-0- 0)3 PC -6 CEP 701 Soil Laboratory ( P a g e

56 Management (3-1-0)4 (3-0-0) 3 Structures(3-0-2)4 Structures (3-0-0)3 Foundations (3-0-0)3 6)3 IX CED 811 Major Project Part 1 (CEG) (0-0-12) 6 PE-2 CEL 614 Geoenvironmental and Geohazards (3-0-0) 3 PE-3 CEL 707 Soil Dynamics and Geotechnical Earthquake (3-0-0) 3 PE-4 CEL 712 Landfills and Ash Ponds (3-0-0) 3 PE-5 CEL 715 Soil Structure Interaction Analysis (3-0-0) X CED 812 MAJOR PROJECT PART 2 ( CEG) (0-0-24) 12 PE-6 CEL 760 Finite Element Method in Geotechnical (3-0-0) P a g e

57 15 The overall credits structure: B.Tech.+M.Tech. [CSE] The overall credits structure OC 10 EAS 17 DE 37 HU & HM 21 PE 18 PC 23 DC 57 BS 20 TOTAL 203 DC S.No. CODE COURSE TITLE L T P CR. 1 CSL 105 Discrete Mathematical Structures CSL 201 Data Structures CSL 211 Computer Architecture EEL 201 Digital Electronics EEP 201 Electronics Lab CSP 301 Design Pract. in Comp. Sc CSL 307 Programming Language MAL 250 Introduction to Probability Theory and Stochastic Processes CSL375 Operating Systems CSL356 Analysis and Design of Algorithms CSL374 Computer Networks CSL432 Programming in Java CSC410 Colloquium (CS) CSD411 Major Project Part-1 (CS) CSL274 Object Oriented Programming Using C DE S.NO. CODE COURSE TITLE L T P CR. 1 CSL 332 Introduction to Database Systems CSL781 Computer Graphics CSL705 Theory of Computation CSL333 Artificial Intelligence CSL728 Compiler Design CSL740 Software CSL759 Cryptography and Computer Security CSD412 Major Project Part 2 (CS) CSL718 Architecture of High Performance Computer Systems CSL834 Data compression Technique CSL765 Introduction to Logical & Functional Programming CSL837 Mobile Computing CSL838 Wireless Networks CSL837 Mobile Adhoc Networks CSL839 Cloud Computing CSL835 Data Mining & Warehousing CSL633 Resource Management in Computer Systems CSL830 Distributed Computing CSL841 Cluster & Grid computing CSL724 Advance Computer Networks P a g e

58 22 CSL758 Advance algorithms CSL847 Distributed Algorithms CSL851 Algorithmic Graph Theory CSL840 Computer Vision CSL868 Special topic in Database Systems CSL862 Special topic in software Systems CSL812 System Level Design and Modeling(Embedded System) CSL555 Microprocessor and Interfaces Advanced Data Structures PE S.NO. CODE COURSE TITLE L T P CR. 1 CSL783 Digital Image Analysis CSL781 Computer Graphics CSL866 Special Topics in Algorithms CSL859 Advanced Computer Graphics CSL728 Compiler Design CSL740 Software CSL718 Architecture of High Performance Computer Systems CSL834 Data compression Technique CSL765 Introduction to Logical & Functional Programming CSL837 Mobile Computing CSL759 Cryptography and Computer Security CSL837 Mobile Adhoc Networks CSL839 Cloud Computing CSL835 Data Mining & Warehousing SIL765 Network & System Security CSL830 Distributed Computing CSL841 Cluster & Grid computing CSL851 Algorithmic Graph Theory S.NO. CODE COURSE TITLE L T P CR. 1 CSD750 Minor Project (CO) CSD851 Major Project Part 1 (CO) CSD852 Major Project Part 2 (CO) CSL718 Architecture of High Performance Computers CSL758 Advanced Algorithms OC S.NO. CODE COURSE TITLE L T P CR. 1 CSL311 Object Oriented Programming CSL313 Database Management System CSL314 Introduction to Operating system CSL741 Introduction to Software CSL376 Introduction to Computer Networks CSL334 Introduction to Artificial Intelligence CSL435 Java Programming CSL835 Data Mining & Warehousing CSL759 Cryptography and Computer Security P a g e

59 Sem. Subject LC L T P WC CR I AML110 Mechanics (3-0-2) 4 CSL101 Introduction to Computers & Programming (3-0-2) 4 CYL110 Chemistry: Concepts & Applications CYP100 Chemistry Laboratory (0-0-4) 2 MAL110 Mathematics I HUL 101 English in Practice-I (2-0-2) II MEL 120 Manufacturing Practice (2-0-3) 3.5 EEL 101 Fundamentals of Electrical (3-0-2) 4 PHL 110 Fields and Waves PHP 100 Physics Lab (0-0-4) 2 MAL120 Mathematics I - MEL110 Graphics Science (0-0-3) 1.5 HUL 110 Communication Skills (2-0-2) III IV CSL 105 Discrete Math. Str. (3-1-0)4 CSL307 Programming Language (3-0-0)3 CSL 201 Data Structures (3-0-4)5 MAL 250 Prob. Stoch Proc (3-1- 0)4 CSL 211 Computer Architecture (3-1-2)5 (DE-1) CSL 332 Intro to DBMS (3-0-3)4.5 CSL312 Programming in C++ (3-0-2)4 CSL375 Operating Systems (3-0-3)4.5 EEL 201 Digital Electronics (3-1-0)4 EEP 201 Electronics Lab-1 (0-0-3) OC1 (3-0-0)3 HUL235 English (Technical Communication) (2-1-0) 3 HUL234 Language & Communicatio n V VI CSL356 Analysis and Design of Algorithms (3-0-2)4 CSL374 Computer Networks (3-0-3)4.5 (DE-3) CSL705 Theory of Computation (3-1-0)4 CSL434 Programming in Java (3-0-2)4 CSL555 Microprocessor and Interfaces(3-1- 2) 5 (DE-4) CSL740 Software (3-0-2)4 (DE-5)CSL781 Computer Graphics (3-0-3)4.5 (DE-18) CSL830 Distributed Computing (3-0- 0)3 - - OC-2 (3-1-0)4 OC-3 (3-0-0) CST -410 Practical Training HUL234 Language & Communicatio n HUL300 Communicatio n Skills & Personality Development VII CSC410 Colloquium (CS) (0-3-0)3 (DE-6) CSL728 Compiler Design (3-0-3)4.5 CSL837 Mobile Computing (3-0-0)3 (DE-8) CSL333 Artificial Intelligence (3-1-0) P a g e

60 VIII (PC-1 ) CSD750 Minor Project (CO) (0-1-6) 4 CSL835 Data Mining & Warehousing (3-1-0)4 (DE-7) CSL759 Cryptography & Computer Security (3-0-0)3 - - * IX (PC-2) CSD851 Major Project Part-1 (CO) (0-0-12)6 (PE-1) (3-0-0)3 (PE-3) (3-0-2)4 (PE-2) (3-0-0)3 (PE- 5) (3-0-2) X - (PE-4) (3-0-2)4 - (PC-3) CSD852 Major Project Part-2 (CO) (0-0-28) P a g e

61 16 The overall credits structure: B.Tech. + M.Tech. [EE] The overall credits structure Undergraduate Core (UC) Undergraduate Elective (UE) Program Core (PC) Program Elective (PE) Category Credits Category Credits Category Credits Category Credits DC 65 DE 20.5 PC 34 PE 18 BS 19 HU & HM 17 EAS 17 OC 10 Total 101 Total 47.5 Over all Credits 201 Total Credits Basic Sciences (BS) Core Code Subject Name L T P Total CYL110 Chemistry: Concepts and Applications CYP100 Chemistry Laboratory MAL110 Mathematics I MAL120 Mathematics II PHL110 Field & Waves PHP100 Physics Laboratory Arts and Sciences (EAS) Core Code Subject Name L T P Total AML110 Mechanics CSL101 Introduction to Computers & Programming EEL101 Fundamentals of Electrical MEL110 Graphic Science MEL120 Manufacturing Practices Humanities and Social Sciences (HC) Core Code Subject Name L T P Total HUL 101 English in Practice-I HUL110 Communication Skills HUL235 English (Technical Communication) HUL234 Language & Communication HUL242 Soft Skills & Personality Development HUL300 Communication Skills & Personality Development Subject Credits S No Code Name Category L T P TOTAL 1 CSL201 Data Structures DC P a g e

62 2 EEC420 Colloquium (EE) DC EED421 Major Project Part 1 (EE) DC EEL201 Digital Electronic Circuits DC EEL202 Circuit Theory DC EEL203 Electromechanics DC EEL204 Analog Electronics Circuits DC EEL205 Signals and Systems DC EEL209 Power Electronics Devices and Circuits DC EEL301 Control - I DC EEL303 Power - I DC EEL305 Electric Drives DC EEL308 Computer Architecture DC EEP201 Electronics Laboratory - I DC EEP203 Electromechanics Laboratory DC EEP204 Electronics Laboratory - II DC EEP209 Power Electronics Laboratory DC EEP301 Control Laboratory DC EEP303 Power Laboratory DC EEP305 Drives Laboratory DC EEP308 Computer Technology Laboratory DC EET420 Practical Training (EE) DC MAL 250 Probability Theory and Stochastic DC S No Subject Credits Code Name Category L T P TOTAL 1 EED422 Major Project Part 2 (EE) DE EEL306 Communication DE EEL325 Control II DE EEL451 Power Systems Protection DE EEP 451 Power Systems Protection Lab DE EEL452 HVDC Transmission DE EEL453 Power System Dynamics and Control DE EEL456 Power II DE EEL339 Power Conditioning DE EEL342 DSP based Control of Electric Drive DE EEL344 Electric Transportation DE EEL346 Electrical Machines and Industrial Drives DE EEL349 Advanced Electrical Machines DE EEL359 Electric Machine Design and CAD of Electric Machines DE EEL365 Intelligent Control DE EEL375 Embedded Systems DE EEL388 Stepper Motors DE P a g e

63 18 EEL389 Computer Aided Testing of Electric Machines DE EEL394 Permanent Magnet Motors DE EEL398 Machines and Drives Dynamics DE EEL404 Flexible AC Transmission System DE EEL405 Power Instrumentation DE EEL407 Distribution System Planning and Automation DE EEL423 Demand Side Management DE EEL424 Nuclear Power Generation DE EEL428 Substation Design DE EEL455 Power System Planning DE EEL458 Power Systems Optimization DE EEL482 Mechatronics DE EEL483 Hydro Power Generation DE EEL486 Illumination and Heating DE EEL487 Intelligent Algorithms for Power Systems DE EEL741 Modelling and Analysis of Electrical Machines DE EEL748 Power Quality DE EEL749 Special Electromechanical Systems DE EEL772 Optimal Control Theory DE Minor Degree-I in Power System S No Subject Credits Code Name L T P TOTAL 1 EEL210 Circuit Analysis EEL312 Electrical Machines EEL310 Control Theory EEL328 Control Theory II EEL332 Power System EEL459 Power System II EEL454 Protection of Power System EEL457 High Voltage AC/DC transmission EEL461 Dynamic Power System and Control Minor Degree-I in Power Electronics S No Subject Credits Code Name L T P TOTAL 1 EEL210 Circuit Analysis EEL214 Digital Electronic Theory EEL208 Electronic devices & Circuits EEL310 Control Theory EEL335 Power Electronics EEL328 Control Theory II P a g e

64 7 EEL425 Power System Instrumentation EEL419 Electrical Drives EEL454 Protection of Power System Program Core (PC) S No Code Subject Name L T P Total 1 EEL 796 Power System Control and Instrumentation EEL 797 Power System Dynamics EEL 894 Flexible AC Transmission System EEP 791 Power System Laboratory EEP 798 Power System Laboratory EED 790 Minor Project EED 890 Major Project Part EED 898 Major Project Part Program Elective (PE) S No Code Subject Name L T P Total 1 EEL 793 Power Systems Transients EEL794 High Voltage DC Transmission EEL799 Power System Reliability EEL 885 EHV AC Transmission EEL892 Power System Communication EEL896 Power System Optimization EEL897 Load forecasting and Load Management EEL 899 Distribution Automation P a g e

65 Sem. Subject LC L T P WC CR CYL 110 MAL110 AML110 CSL101 CYP 100 HUL101 I II Chemistry: Concepts and Applications Mathematics-I Mechanics Introduction to Computers and Programming Chemistry Laboratory English in Practice-I PHL 110 MAL 120 EEL 101 MEL 120 MEL110 PHP100 HUL110 Fields and Waves Mathematics-II Fundamentals of Electrical Manufacturing Practices Graphic Science Physics Laboratory Communication Skills III IV EEL 201 EEL 202 EEL 203 EEL 205 EEP 201 EEP 203 HUL235 Digital Electronic Circuits Circuit Theory Electromechanics Signals and Systems Electronics Laboratory - I Electromechanics Laboratory English (Technical Communication) EEL 204 MAL250 EEL 301 EEP 204 EEP 301 HUL 234 EEL210 Analog Electronics Circuits Probability theory and stochastic Control - I Electronics Laboratory - II Control Laboratory Language and Communication Circuit Analysis EEL 303 CSL 201 EEL 306 EEL 325 EEP 303 HUL 242 EEL310 EEL V Power - I Data Structures Communication Control - II Power Laboratory Soft Skills & Personality Development Control Theory Electrical Machines EEL 209 EEL 308 EEP 308 EEL 456 EEP 209 HUL 300 EEP 209 VI Power Electronics Devices and Circuits Computer Architecture Computer Technology Laboratory Power - II Power Electronics lab Communication Skills & Personality Development Power Electronics lab P a g e

66 EET 420 PRACTICAL TRAINING (EE) VII EEC 420 EEL 305 EEL 451 EEP 305 EEP 451 EEL 796 EEL 797 Colloquium (EE) Electric Drives Power Systems Protection Drives Lab Power Systems Protection Lab Power System Control and Instrumentation Power System Dynamics EEL 452 EEL 453 EED 790 EEL793 EEL 894 EEP VIII HVDC Transmission Power System Dynamics and Control Minor Project Power Systems Transients Flexible AC Transmission System Power System Laboratory Summ er IX X EED 890 Major Project Part 1 EED890 EEL794 EEL799 EEL 885 EEL896 EEP 798 Major Project Part 1 High Voltage DC Transmission Power System Reliability EHV AC Transmission Power System Optimization Power System Laboratory EED898 Major Project Part 2 EEL897 Load forecasting and Load Management P a g e

67 17 The overall credits structure: B.Tech.+M.Tech. [ECE] The overall credits structure Undergraduate Core (UC) Undergraduate Elective (UE) Program Core (PC) Program Elective (PE) Category Credits Category Credits Category Credits Category Credits DC 58.5 DE 29 PC 35 PE 20 BS 19 HU & HM 17 EAS 17 OC 10 Total 94.5 Total 56 Over all Credits Total Credits Basic Sciences (BS) Core Code Subject Name L T P Total CYL110 Chemistry: Concepts and Applications CYP100 Chemistry Laboratory MAL110 Mathematics I MAL120 Mathematics II PHL110 Field & Waves PHP100 Physics Laboratory Arts and Sciences (EAS) Core Code Subject Name L T P Total AML110 Mechanics CSL101 Introduction to Computers & Programming P a g e

68 EEL101 Fundamentals of Electrical MEL110 Graphic Science MEL120 Manufacturing Practices Humanities and Social Sciences (HC) Core Code Subject Name L T P Total HUL 101 English in Practice-I HUL110 Communication Skills HUL235 English (Technical Communication) HUL234 Language & Communication HUL242 Soft Skills & Personality Development HUL300 Communication Skills & Personality Development S No Subject Credits Code Name Category L T P TOTAL 1 EEL205 Signals and Systems DC EEL202 Circuit Theory DC EEL201 Digital Electronic Circuits DC EEP201 Electronics Lab-I DC EEL204 Analog Electronics Circuits DC EEL301 Control Engg-1 DC EEP204 Electronics Lab-II DC MAL250 Prob Soch proc. DC EEP301 Control Engg lab DC EEL207 Engg Electromagnetics DC EEP307 Electromagnetics Lab DC EEL306 Comm. Engg. DC EEP306 Comm. Engg Laboratory DC P a g e

69 14 EEL441 Industrial Electronics DC EEL318 Microprocessor DC EEL322 Integrated Circuits Technology DC EEL329 VLSI Technology and Design DC EEL338 Antennas and Propagation DC EED421 Major Project Part-I DC EEP205 Signal Processing Lab-1 DC EEL334 Wireless Communication DC EET420 Practical Training(ECE) DC S No Subject Credits Code Name Category L T P TOTAL 1 CSL201 Data structures DE EEL308 Computer Architecture DE EEL358 Operating Systems DE EEL321 Digital Hardware Designs DE EEL442 OP-Amps and Linear Integrated circuits DE EEL316 Digital Comm. DE EEL713 Microwave Theory and Circuits DE EEL319 Digital Signal Processing DE EEC420 Colloquium (ECE) DE EED412 Major Project Part 2 (ECE) DE List of Open Core for Minor Degree (Communication ) Subject Credits S No Code Name L T P TOTAL 1 EEL208 Electronic devices & Circuits P a g e

70 2 EEL313 Signals System EEL314 Communication Theory EEL333 Communication Theory-II EEL336 Advanced Signal Processing EEL434 Optical Communication EEL474 Antenna Fundamentals EEL436 Mobile Communication EEL471 Telecommunication and Switching Networks List of Open Core for Minor Degree( Integrated Electronics &Circuits ) Subject Credits S No Code Name L T P TOTAL 1 EEL208 Electronic devices & Circuits EEL343 Integrated Circuits EEL345 Digital System Design EEL347 CMOS VLSI Design EEL336 Advanced Signal Processing EEL439 Operational Amplifier EEL429 Microelectronic Circuits EEL476 Analog Mixed Signal Ics EEL475 Telecommunication and Switching Networks Program Core (PC) S No Subject Credits Code Name Category L T P TOTAL 1 EEL762 Digital Communication PC CRL702 Architecture & Algo. For DSP system PC P a g e

71 3 EEL731 DSP-I PC EEL711 Signal Theory PC EED790 Minor Project PC EED890 Major Project Part-1 PC EED898 Major Project Part-2 PC Program Electives (PE) S No Subject Credits Code Name Category L T P TOTAL 1 CRL731 Selected topics in RFDT 1 PE CRL732 Selected topics in RFDT 2 PE CRL733 Selected topics in RFDT 3 PE CRL711 CAD of RF & Microwave Devices PE CRL734 Adaptive filter theory PE ESL736 Power from renewable & environment impacts PE P a g e

72 Sem. LC L T P WC CR I CYL 110 MAL110 AML110 CSL101 CYP 100 HUL101 Chemistry: Concepts and Applications Mathematics-I Mechanics Introduction to Computers and Programming Chemistry Laboratory English in Practice-I PHL 110 MAL 120 EEL 101 MEL 120 MEL110 PHP100 HUL II Fields and Waves Mathematics-II Fundamentals of Electrical Manufacturing Practices Graphic Science Physics Laboratory Communication Skills EEL 201 EEL 202 CSL 201 EEL 205 EEP 201 HUL235 III Digital Electronic Circuits Circuit Theory Data Structure Signals and Systems Electronics Laboratory - I English (Technical Communication ) EEL 204 MAL 250 EEL 301 EEP 204 EEP 301 EEL 207 HUL 234 EEP 307 IV Analog Electronics Circuits Probability theory and stochastic Control - I Electronics Laboratory - II Control Laboratory Electromagnetic s Language and Communication Electromagnetic s Lab OC P a g e V EEL 306 EEL 321 EEL 308 EEL 442 EEP 306 EEP 205 HUL

73 Communicatio n Digital Hardware Design Computer Architecture OP-AMPS & Linear Integrated Circuits Communicatio n Laboratory Signal Processing Laboratory-I Soft Skills & Personality Development EEL441 EEL 318 EEL 316 EEL 713 HUL 300 OC-2 OC-3 VI Industrial Electronics Microprocesso r Digital Communicatio n Microwave Theory & Circuits Communication Skills & Personality Development ECT 420 PRACTICAL TRAINING (EP) EEL 338 EEL 319 EEC 420 EEL 762 CRL 702 CRL 731 VII Antennas & Propagation Digital Signal Processing Colloquium(E P) Digital Communication Architecture & Algo For DSP System Selected Topics in RFDT EEL 329 EEL 334 EED 790 EEL 731 CRL 732 CRL 733 VIII VLSI Technology & Design Wireless Communicatio n Minor Project DSP I Selected Topics in RFDT 2 Selected Topics in RFDT Summ er EED 890 EEL 711 CRL 711 CRL 734 EED 861 MAJOR PROJECT PART- I IX X Major Project Part P a g e Signal Theory CAD of RF & Microwave Devices Adaptive Filter Theeory EED 898 ESL 736 Major Project Part 2 Power From Renewable & Environment Impacts

74 P a g e

75 18 The overall credits structure: B.Tech.+ M.Tech. [Mechanical] The overall credits structure OC 10 EAS 17 DE 23 HU & HM 21 DC 81 PE 22 BS 19 PC 38 TOTAL 232 Basic Sciences (BS) Core L T P Total CYL110 Chemistry: Concepts and Applications CYP100 Chemistry Laboratory MAL110 Mathematics I MAL120 Mathematics II PHL110 Field & Waves PHP100 Physics Laboratory Arts and Sciences (EAS) Core L T P Total AML110 Mechanics CSL101 Introduction to Computers & Programming EEL101 Fundamentals of Electrical MEL110 Graphic Science MEL120 Manufacturing Practices Humanities and Social Sciences (HC) Core L T P Total HUL 101 English in Practice-I HUL110 Communication Skills HUL235 English (Technical Communication) HUL234 Language & Communication HUL242 Soft Skills & Personality Development HUL300 Communication Skills & Personality Development List of Department core ( DC) Course Code Course Name L T P Credit MEL140 Thermodynamic AML160 Mechanics of Fluids MEL211 Kinematics and Dynamics of Machines AML140 Mechanics of Solids AMP261 Solids Laboratory P a g e

76 AMP262 Fluids Laboratory MEP201 Mechanical Drawing MEL241 Energy Conversion MEL236 Material Science MEL232 Casting, Welding and Forming MAL230 Numerical Methods MEL221 Operations Research MEL242 Heat and Mass Transfer MEL311 Machine Element Design MEL233 Machining, Machine Tools and Metrology MEL312 Mechanical Measurement, Control Theory & Applications MEP341 Thermal Laboratory MEL322 Operations Planning and Control MEL410 Practical Training MEC410 Colloquium MED411 Major Project Part MEL421 Production Management MEL425 Flexible Manufacturing Systems Departmental Electives (DE) Course Code Course Name L T P Credit MED310 Mini Project (ME) MEL310 Concurrent MEL314 Noise MEL316 Mechanical Vibrations MEL321 Ergonomics MEL332 Design and Manufacturing of Composites MEL333 Metrology MEL334 Low Cost Automation MEL341 Gas Dynamics and Propulsion MEL342 Power Plant Technologies MEL343 Fuels, Combustion and Pollution MEL344 Refrigeration and Air-Conditioning MEL345 Internal Combustion Engines MEL346 Turbo-machinery MEL410 Creativity in MEL411 Mechatronics MEL412 Advanced Mechanical Design MEL413 Design of Mechanisms MEL414 Computer Aided Mechanical Design MEL415 Vibrations Design MEL416 Robotics MEL417 Lubrication MEL420 Total Quality Management MEL422 Project Management MEL425 Flexible Manufacturing Systems MEL431 CNC Machines and Programming MEL432 Microprocessor Applications in Manufacturing MEL433 Micro- and Nano- Manufacturing MEL434 Design for Manufacturing and Assembly MEL435 Geometric Modelling for Manufacturing P a g e

77 MEL436 Injection Moulding and Mould Design MEL441 Modelling and Experiments in Heat Transfer MEL442 Thermal Analysis of Bio-systems MEL716 Nano Scale Heat Transfer MED412 Major Project Part 2 (ME) Program Electives (PE) Course Code Course Title L T P Credit MEL674 Principles of Management MEL732 Machine Tool Design MEL749 Mechatronic Product Design MEL751 Industrial and Systems MEL752 Quality Assurance MEL763 Methods and Ergonomics MEL772 Metal forming Technology MEL775 IT in Manufacturing Enterprises MEL778 Design and Metallurgy of Welded Joints MEL783 Automation in Manufacturing MEL792 Injection Moulding and Mould Design MEL794 CAD/CAM MEL796 Rapid Prototyping and Tooling MEP790 Process MES880 Independent Study (MEP) Programme Core (PC) Course Code Course Title L T P Credit MEL769 Metal forming Analysis MEL780 Casting Technology MEL781 Machining Processes and Analysis MEL784 CNC Technology and Programming MEL787 Welding and Allied Processes MEL791 Composite Materials and Processing P a g e

78 I II III IV Sem. Subject LC L T P WC CR. AML110 Mechanics (3-0-2) 4 MEL 120 Manufacturing Practice (2-0-4) 4 MEL 140 Thermodynamics MEL236 Material Science CSL101 Introduction to Computers & Programming (3-0-2) 4 EEL 101 Fundamentals of Electrical (3-0-2) 4 AML160 Mechanics of Fluids MEL232 Casting, Welding & Forming (3-0-2) 4 CYL110 Chemistry: Concepts & Applications PHL 110 Fields & Waves MEL 211 Kinematics & Dynamics of Machines (3-0-2) 4 MAL230 Numerical Methods CYP100 Chemistry Laboratory (0-0-4) 2 PHP 100 Physics Lab (0-0-4) 2 AML140 Mechanics of Solids MEL221 Operations Research MAL110 Mathematics I MAL120 Mathematics I AMP261 Fluids Laboratory (0-0-3) 1.5 ENV101 Environmental Studies (0-0-0) 0 MEP 201 Mechanical Drawing (1-0-3) 2.5 MEL110 Graphics Science (0-0-3) 1.5 AMP262 Solids Laboratory (0-0-3) 1.5 OC-1 (3-0-0) 3 HUL 101 English in Practice-I (2-0-2) 3 HUL 110 Communication Skills (2-0-2) 3 HUL235 English (Technical Communication) (2-1-0) 3 HUL234 Language & Communication V VI VII VIII MEL242 Heat and Mass Transfer MEL312 Mechanical Measurement, Control Theory & Applications (3-1-2) 5 MED310 Mini Project (ME) (0-0-8) 4 MEL311 Machine Element Design (3-1-2) 5 MEP341 Thermal Laboratory (0-0-3) 1.5 DE-3 (MEL342) Power Plant Technologies DE-5 (MEL316) Mechanical Vibrations (3-0-2) 4 MEL233 Machining, Machine Tools and Metrology (3-0-2) 4 DE-1 (MEL344) Refrigeration & Air Conditioning DE-4 (MEL425) Flexible Manufacturin g Systems (3-0-0) 3 DE-6 (MEL420) Total Quality Management MEL322 Operations Planning and Control (3-0-0) MEC410 Colloquium (ME) (0-3-0) 3 PE-1 MEL674 Principles of Management (3-0-0) 3 DE-2 (MEL34 5) I.C. Engine MEL241 Energy Conversion OC-2 (3-0-0) 3 MET410 Practical Training (ME) MEL421 Production Management PC-1 MEL781 Machining Processes and Analysis (3-0-2) 4 PC-3 MEL784 CNC Technology and Programming (3-0-2) 4 OC-3 PC-2 MEL780 Casting Technology (3-0-2) 4 PC-4 MEL791 Composite Materials and Processing (3-0-2) 4 HUL242 Soft Skills & Personality Development HUL300 Communication Skills & Personality Development P a g e

79 IX X MED881 Major Project Part 1 (ME) (0-0-12) 6 DE- 7 MED882 Major Project Part 2 (ME) (0-0-24) 12 PE-2 MEL732 Machine Tool Design (3-0-2) 4 PE-6 MEL794 CAD/CAM (3-0-2) 4 PE-3 MEL775 IT in Manufacturing Enterprises (3-0-0) 3 PE-4 MEL778 Design and Metallur gy of Welded Joints (3-0-2) 4 PE-5 MEL783 Automation in Manufacturin g (3-0-2) P a g e

80 19 The overall credits structure: B.Tech. + MBA [Civil] LIST OF DEPARTMENTAL CORE IN CIVIL ENGINEERING S NO CODE SUBJECT L T P CREDIT 1 CEC 210 Colloquium CED 411 Major project part CEL 212 Environmental Engg CEL 222 Engg Geology & soil Mechanics CEL 231 Structural Analysis CEL 232 Concrete Material & design CEL 241 Transportation engg CEL 251 Hydrology & hydraulics CEL 271 Elements of Surveying CEL 321 Geotechnical engg CEL 331 Structural Analysis -II CEL 332 Design of steel structure CEL 351 Design of hydraulic structure CEL 339 Concrete Technology & material AML 170 Fluid Mechanics LIST OF DEPARTMENTAL ELECTIVE IN CIVIL ENGINEERING S NO CODE SUBJECT L T P CREDIT 1 CEL 311 Advance water & waste water engg CEL 341 Transportation engg -II CEL 362 Construction management CEL 411 Industrial waste management CEL 412 Environmental Assessment Methodologies CEL 421 Ground improvement technology CEL 422 Rock engg CEL 423 Design of foundation, earth & earth retaining Structure P a g e

81 9 CEL 431 Advance Structure analysis CEL 432 Design of prestressed concrete & industrial Structure CEL 433 Advanced Structural Design CEL 442 Traffic & transportation planning CEL 443 Transportation safety & environment CEL 451 Water power engg CEL 453 Water resources Management CEL 455 Introduction to geographic information system CEL 459 River Mechanics CEL 464 Construction contract & economics CEL 466 Construction equipment & methods CEP 452 Computational aspects in water resources CED 412 Major project part -II Course Code MBA Semester I L T P C CSL 702 Computer Application In Management HUL 103 Business Communication SML 101 Management Concepts MBA-1 SML 312 Organizational Behavior MBA-3 SML 105 Accounting For Managers MBA-5 SML 760 Marketing Management MBA-6 SML 115 Managerial Economics MBA-2 MAL 215 Mathematical Statistics For Management Decision Course Code MBA Semester II L T P C SML 705 Financial Management MBA-7 SML731 Human Resource Management MBA-8 SML 895 Management of Research Methodology MBA-9 SML 745 Operations Management SML 850 Management of Information Technology MAL 280 Operation Research SML 721 Corporate Business Environment MBA-4 SML 794 Communication Skills & Personality Development P a g e

82 Course Code MBA III Semester L T P C SML 732 Business Strategy MBA-10 SML 302 Entrepreneurship development SMD 700 Summer Training Project report MBA-12 SML 761 Consumer Behavior SML 762 Service Marketing SML 763 Retail Management SML 873 Security Analysis and Investment Management SML 876 Project Appraisal Planning and Control SML 877 Banking Service Operations SML 735 Training and Development SML 736 Performance Management & Reward System SML 737 Strategic Human Resource Management Marketing Electives Finance Electives HR Electives MBA-14 MBA-15 MBA-16 MBA-14 MBA-15 MBA-16 MBA-14 MBA-15 MBA-16 Course Code MBA IV Semester L T P C SML 801 Business Ethics and Corporate Governance MBA-11 SML 203 Business Law MBA-13 SML 811 Industrial Marketing MBA-17 Marketing SML 812 Sales and Distribution Management MBA-18 Electives SML 813 Advertising, Brand, Media Management MBA-19 SML 821 Portfolio Management and Mutual Funds MBA-17 Finance SML 822 Management of Financial Services MBA-18 Electives SML 823 Advanced Management Accounting MBA-19 SML 831 Leadership Skills and Change Management MBA-17 HR SML 832 Labour Law and Compensation Management MBA-18 Electives SML 833 Human Resources Planning MBA-19 SMD 800 Management Thesis MBA P a g e

83 The overall credits structure OC 10 EAS 17 DE 22 HU/HM 21 DC 79 MBA (core) 40 BS 19 MBA ( ELECTIVE) 18 TOTAL 226 Sem Subject LC L T P WC CR. I AML110 Mechanics (3-0-2) 4 CSL101 Introduction to Computers & Programming (3-0-2) 4 CYL110 Chemistry: Concepts & Applications CYP100 Chemistry Laboratory (0-0-4) 2 MAL110 Mathematics I HUL 101 English in Practice-I (2-0-2) II MEL 120 Manufacturing Practice (2-0-3) 3.5 EEL 101 Electrical (3-0-2) 4 PHL 110 Fields & Waves PHP 100 Physics Lab (0-0-3) 1.5 MAL120 Mathematics I MEL110 Graphics Science (0-0-3) 1.5 HUL 110 Communication Skills (2-0-2) III CEL 231 Structural Analysis - I (3-1-2)5 CEL 241 Transportation Engg-1(3-0-2)4 AML 170 Fluid Mechanics (3-0-2) 4 CEL 271 Elements of surveying (2-0-2)3 CEL 339 Concrete technology & Materials(3-0-0)3 HUL 235 English (Technical Communication) (2-1-0) IV CEL 212 Environmenta l Engg(3-0-2)4 Math- (3-1-0)4 CEL 222 Engg Geology & soil mechanics (3-1-3)5.5 CEL251 Hydrology & Hydraulics (3-1-4)6 OC 1 (3-1-0)4 HUL234 Language & Communication (3-1-0) V CEL 321 Geotechnical Engg (3-1- 3)5.5 CEL 331 Structural Analysis -II(3-1-2)5 DE-1 CEL 341Transportation Engg-II (3-1-0)4 DE-2 CEL 311 Advanced water & wastewater engg (3-0-2) 4 OC-2 (3-0-0)3 OC-3 (3-0-0)3 HUL242 Soft Skills and Personality Development (3-1- 0) VI CEL 332 Design of Steel Structure SML 101 Management Concepts CEL 232 Concrete material & design (3-1-4)6 DE-3 CEL 466 Construction Equipments & Methods (2-1-0) 3 HUL300 Hu & So Sc. #2 (3-1-0) P a g e

84 (3-1-2) 5 (3-1-0)4 CET-410 Practical Training VII CEC 410 Colloquium (0-3-0)3 CEL 351 Design of hydraulic structures (2-0-2) 3 DE-4 CEL 423 Design of foundation, Earth & Earth retaining structure (3-1-0)4 SML 115 MANAGERIAL ECONOMICS (3-1-0)4 SML 312 ORGANIZATIO NAL BEHAVIOR (3-1-0)4 SML 721 Corporate Business Environment (3-1-0)4 SML 105 ACCOUNTING FOR MANAGERS (3-1-0) VIII CED310 Mini Project (CE) (0-0-6)3 (DC) DE-5 CEL 453 Water Resources Management (3-1-0)4 DE-6 CEL 411 Industrial waste management(3-0- 0)3 SML 760 MARKETING MANAGEMENT (3-1-0)4 SML 705 Financial Management (3-1-0)4 SML 731 Human Resource Management (3-1-0)4 SML 895 Management of Research Methodology (3-1-0) MBA-SUMMER TRANING IX DE-7 CEL464 Constructio n contract & economics( 3-0-0)3 CED 811 (DE) Major Project Part 1 (CEG) (0-0-12) 6 SML 732 Business Strategy (3-1-0)4 SML 801 Business Ethics and Corporate Governance (3-1-0)4 SMD 700 Summer Training Project (0-0-4)2 MBA 14 (3-0- 0)3 MBA 15 (3-0-0)3 MBA 16 (3-0-0) X SMD 800 MANAGEMEN T THESIS (0-0-4)2 DE Traffic & transportation planning (2-1- 0)3 SML 203 Business Law (3-1-0)4 MBA-17 (3-0-0)3 MBA-18 (3-0-0)3 MBA-19 (3-0-0) P a g e

85 20 The overall credits structure: B.Tech.+MBA [CSE] The overall credits structure DE 46 HU & HM 21 DC 57 OC 10 BS 20 MBA 58 EAS 17 TOTAL 229 S.No. Code Course Title L T P CR. 1 CSL 105 Discrete Mathematical Structures CSL 201 Data Structures CSL 211 Computer Architecture EEL 201 Digital Electronics EEP 201 Electronics Lab CSP 301 Design Pract. in Comp. Sc CSL 307 Programming Language MAL 250 Introduction to Probability Theory and Stochastic Processes CSL375 Operating Systems CSL356 Analysis and Design of Algorithms CSL374 Computer Networks CSL432 Programming in Java CSC410 Colloquium (CS) CSD411 Major Project Part-1 (CS) CSL274 Object Oriented Programming Using C P a g e DE S.No. Code Course Title L T P CR. 1 CSL 332 Introduction to Database Systems CSL781 Computer Graphics CSL705 Theory of Computation CSL333 Artificial Intelligence CSL728 Compiler Design CSL740 Software CSL759 Cryptography and Computer Security CSD412 Major Project Part 2 (CS) CSL718 Architecture of High Performance Computer Systems CSL834 Data compression Technique CSL765 Introduction to Logical & Functional Programming CSL837 Mobile Computing CSL838 Wireless Networks CSL837 Mobile Adhoc Networks CSL839 Cloud Computing CSL835 Data Mining & Warehousing CSL633 Resource Management in Computer Systems

86 18 CSL830 Distributed Computing CSL841 Cluster & Grid computing CSL724 Advance Computer Networks CSL758 Advance algorithms CSL847 Distributed Algorithms CSL851 Algorithmic Graph Theory CSL840 Computer Vision CSL868 Special topic in Database Systems CSL862 Special topic in software Systems CSL812 System Level Design and Modeling(Embedded System) CSL555 Microprocessor and Interfaces Advanced Data Structures PE S.No. Code Course Title L T P CR. 1 CSL783 Digital Image Analysis CSL781 Computer Graphics CSL866 Special Topics in Algorithms CSL859 Advanced Computer Graphics CSL728 Compiler Design CSL740 Software CSL718 Architecture of High Performance Computer Systems CSL834 Data compression Technique CSL765 Introduction to Logical & Functional Programming CSL837 Mobile Computing CSL759 Cryptography and Computer Security CSL833 Mobile Adhoc Networks CSL839 Cloud Computing CSL835 Data Mining & Warehousing SIL765 Network & System Security CSL830 Distributed Computing CSL841 Cluster & Grid computing CSL851 Algorithmic Graph Theory PC S.NO. CODE COURSE TITLE L T P CR. 1 CSD750 Minor Project (CO) CSD851 Major Project Part 1 (CO) CSD852 Major Project Part 2 (CO) CSL718 Architecture of High Performance Computers CSL758 Advanced Algorithms Course Code MBA Semester I L T P C CSL 702 Computer Application In Management HUL 103 Business Communication SML 101 Management Concepts MBA-1 SML 312 Organizational Behavior MBA-3 SML 105 Accounting For Managers MBA-5 SML 760 Marketing Management MBA-6 SML 115 Managerial Economics MBA-2 MAL 215 Mathematical Statistics For Management Decision Course Code MBA Semester II L T P C SML 705 Financial Management MBA-7 SML731 Human Resource Management MBA-8 86 P a g e

87 SML 895 Management of Research Methodology MBA-9 SML 745 Operations Management SML 850 Management of Information Technology MAL 280 Operation Research SML 721 Corporate Business Environment MBA-4 SML 794 Communication Skills & Personality Development P a g e

88 Course Code MBA III Semester L T P C SML 732 Business Strategy MBA-10 SML 302 Entrepreneurship development SMD 700 Summer Training Project report MBA-12 SML 761 Consumer Behavior SML 762 Service Marketing SML 763 Retail Management SML 873 Security Analysis and Investment Management SML 876 Project Appraisal Planning and Control SML 877 Banking Service Operations SML 735 Training and Development SML 736 Performance Management & Reward System SML 737 Strategic Human Resource Management Marketing Electives Finance Electives HR Electives MBA-14 MBA-15 MBA-16 MBA-14 MBA-15 MBA-16 MBA-14 MBA-15 MBA-16 Course Code MBA IV Semester L T P C SML 801 Business Ethics and Corporate Governance MBA-11 SML 203 Business Law MBA-13 SML 811 Industrial Marketing MBA-17 Marketing SML 812 Sales and Distribution Management MBA-18 Electives SML 813 Advertising, Brand, Media Management MBA-19 SML 821 Portfolio Management and Mutual Funds MBA-17 Finance SML 822 Management of Financial Services MBA-18 Electives SML 823 Advanced Management Accounting MBA-19 SML 831 Leadership Skills and Change Management MBA-17 HR SML 832 Labour Law and Compensation Management MBA-18 Electives SML 833 Human Resources Planning MBA-19 SMD 800 Management Thesis MBA P a g e

89 Sem. Subject LC L T P WC CR. I II III IV AML110 Mechanics (3-0-2) 4 MEL 120 Manufacturing Practice (2-0-3) 3.5 CSL 105 Discrete Math. Str. (3-1- 0)4 CSL307 Programming Language (3-0-0)3 CSL101 Introduction to Computers & Programming (3-0-2) 4 EEL 101 Fundamentals of Electrical (3-0-2) 4 CSL 201 Data Structures (3-0-4)5 MAL 250 Prob. Stoch Proc (3-1-0)4 CYL110 Chemistry: Concepts & Applications PHL 110 Fields & Waves CSL 211 Computer Architecture (3-1-2)5 (DE-1) CSL 332 Intro to DBMS (3-0-3)4.5 CYP100 Chemistry Laboratory (0-0-4) 2 PHP 100 Physics Lab (0-0-4) 2 CSL312 Programming in C++ (3-0-2)4 CSL375 Operating Systems (3-0-3)4.5 MAL110 Mathematics I MAL120 Mathematics I EEL 201 Digital Electronics (3-1-0)4 EEP 201 Electronics Lab-1 (0-0- 3)1.5 MEL110 Graphics Science (0-0-3)1.5 OC1 (3-0-0)3 HUL 101 English in Practice-I (2-0-2) 3 HUL 110 Communication Skills (2-0-2) 3 HUL235 English (Technical Communication) (2-1-0) 3 HUL234 Language & Communication V CSL356 Analysis & Design of Algorithms (3-1-2)5 (DE-3) CSL705 Theory of Computation (3-1-0)4 CSL555 Microprocessor and Interfaces(3-1-2) 5 (DE-5) CSL781 Computer Graphics (3-0-3)4.5 OC-2 (3-1-0)4 OC-3 (3-0-0)3 HUL242 Soft Skills & Personality Development VI VII VIII IX X CSL374 Computer Networks (3-0-3)4.5 CSC410 Colloquium (CS) (0-3-0)3 CSD411 Minor Project (CS) (0-0-8) 4 CSL434 Programming in Java (3-0-2)4 (DE-6) CSL728 Compiler Design (3-0-3)4.5 CSL835 Data Mining & Warehousing (3-1-0)4 CSD412 Major Project Part (0-0-16)8 (DE-4) CSL740 Software (3-0-2)4 Mobile Computing (3-0-0)3 (DE-7) CSL759 Cryptography & Computer Security (3-0-0)3 CSL830 Distributed Computing (3-0- 0)3 (DE-8) CSL333 Artificial Intelligence (3-1-0)4 MBA-10 (3-0-0)3 CST -410 Practical Training MBA-11 (3-0-0)3 MBA-13 (3-0-0)3 MBA-2 (3-0-0)3 MBA-6 (3-0-0)3 MBA-14 (3-0-0)3 MBA-17 (3-0-0)3 MBA-3 (3-0-0)3 MBA-7 (3-0-0)3 MBA-15 (3-0-0)3 MBA-18 (3-0-0)3 MBA-1 (3-0-0) 3 MBA-4 (3-0-0) 3 MBA-8 (3-0-0) 3 MBA-16 (3-0-0) 3 MBA-19 (3-0-0)3 HUL300 Communication Skills & Personality Development (2-1-2) 4 MBA-5 (3-0-0)3 MBA-9 (3-0-0)3 MBA-12 Summer Training Project (0-0-4)2 MBA-20 Management Thesis (0-0-4) P a g e

90 21 The overall credits structure B.Tech.+MBA [EE] The overall credits structure Undergraduate Core (UC) Undergraduate Elective (UE) MBA Core (MC) MBA Elective (ME) Category Credits Category Credits Category Credits Category Credits DC 67.5 DE 28.5 MC 52 ME 24 BS 19 HU & HM 17 EAS 17 OC Total Total 55.5 Over all Credits 235 Total Credits 159 Basic Sciences (BS) Core Code Subject Name L T P Total CYL110 Chemistry: Concepts and Applications CYP100 Chemistry Laboratory MAL110 Mathematics I MAL120 Mathematics II PHL110 Field & Waves PHP100 Physics Laboratory Arts and Sciences (EAS) Core Code Subject Name L T P Total AML110 Mechanics CSL101 Introduction to Computers & Programming EEL101 Fundamentals of Electrical P a g e

91 MEL110 Graphic Science MEL120 Manufacturing Practices Humanities and Social Sciences (HC) Core Code Subject Name L T P Total HUL 101 English in Practice-I HUL110 Communication Skills HUL235 English (Technical Communication) HUL234 Language & Communication HUL242 Soft Skills & Personality Development HUL300 Communication Skills & Personality Development S No Subject Credits Code Name Category L T P TOTAL 1 CSL201 Data Structures DC EEC420 Colloquium (EE) DC EED421 Major Project Part 1 (EE) DC EEL201 Digital Electronic Circuits DC EEL202 Circuit Theory DC EEL203 Electromechanics DC EEL204 Analog Electronics Circuits DC EEL205 Signals and Systems DC EEL209 Power Electronics Devices and Circuits DC EEL301 Control - I DC EEL303 Power - I DC EEL305 Electric Drives DC EEL308 Computer Architecture DC EEP201 Electronics Laboratory - I DC P a g e

92 15 EEP203 Electromechanics Laboratory DC EEP204 Electronics Laboratory - II DC EEP209 Power Electronics Laboratory DC EEP301 Control Laboratory DC EEP303 Power Laboratory DC EEP305 Drives Laboratory DC EEP308 Computer Technology Laboratory DC EET420 Practical Training (EE) DC MAL 250 Probability Theory and Stochastic DC S No Subject Credits Code Name Category L T P TOTAL 1 EED422 Major Project Part 2 (EE) DE EEL306 Communication DE EEL325 Control II DE EEL451 Power Systems Protection DE EEP 451 Power Systems Protection Lab DE EEL452 HVDC Transmission DE EEL453 Power System Dynamics and Control DE EEL456 Power II DE EEL339 Power Conditioning DE EEL342 DSP based Control of Electric Drive DE EEL344 Electric Transportation DE EEL346 Electrical Machines and Industrial Drives DE EEL349 Advanced Electrical Machines DE EEL359 Electric Machine Design and CAD of Electric Machines DE EEL365 Intelligent Control DE EEL375 Embedded Systems DE P a g e

93 17 EEL388 Stepper Motors DE EEL389 Computer Aided Testing of Electric Machines DE EEL394 Permanent Magnet Motors DE EEL398 Machines and Drives Dynamics DE EEL404 Flexible AC Transmission System DE EEL405 Power Instrumentation DE EEL407 Distribution System Planning and Automation DE EEL423 Demand Side Management DE EEL424 Nuclear Power Generation DE EEL428 Substation Design DE EEL455 Power System Planning DE EEL458 Power Systems Optimization DE EEL482 Mechatronics DE EEL483 Hydro Power Generation DE EEL486 Illumination and Heating DE EEL487 Intelligent Algorithms for Power Systems DE EEL741 Modelling and Analysis of Electrical Machines DE EEL748 Power Quality DE EEL749 Special Electromechanical Systems DE EEL772 Optimal Control Theory DE Minor Degree-I in Power System S No Subject Credits Code Name L T P TOTAL 1 EEL210 Circuit Analysis EEL312 Electrical Machines EEL310 Control Theory EEL328 Control Theory II P a g e

94 5 EEL332 Power System EEL459 Power System II EEL454 Protection of Power System EEL457 High Voltage AC/DC transmission EEL461 Dynamic Power System and Control Minor Degree-I in Power Electronics S No Subject Credits Code Name L T P TOTAL 1 EEL210 Circuit Analysis EEL214 Digital Electronic Theory EEL208 Electronic devices & Circuits EEL310 Control Theory EEL335 Power Electronics EEL328 Control Theory II EEL425 Power System Instrumentation EEL419 Electrical Drives EEL454 Protection of Power System MBA Core S No Code Subject Name L T P Total 1 SML 101 Management Concepts SML115 Managerial Economics SML312 Organizational Behavior SML721 Corporate Business Environment SML105 Accounting For Managers SML760 Marketing Management SML705 Financial Management P a g e

95 8 SML731 Human Resource Management SML895 Management Of Research Methodology SML732 Business Strategy SML801 Business Ethics And Corporate Governance SMD700 Summer Training Project SML203 Business Law SMD800 Management Thesis SML 101 Management Concepts MBA Electives (ME) Marketing Elective Code Subject Name L T P Total MBA 14 SML 761 Consumer Behavior MBA 15 SML 762 Service Marketing MBA 16 SML 763 Retail Management MBA 17 SML 811 Industrial Marketing MBA 18 SML 812 Sales and Distribution Management MBA 19 SML 813 Advertising, Brand, Media Management Finance Elective Code Subject Name L T P Total MBA 14 SML 873 Security Analysis and Investment Management MBA 15 SML 876 Project Appraisal Planning and Control MBA 16 SML 877 Banking Service Operations MBA 17 SML 821 Portfolio Management and Mutual Funds MBA 18 SML 822 Management of Financial Services MBA 19 SML 823 Advanced Management Accounting HR Elective Code Subject Name L T P Total 95 P a g e

96 MBA 14 SML 735 Training and Development MBA 15 SML 736 Performance Management and Reward System MBA 16 SML 737 Strategic Human Resource Management MBA 17 SML 831 Leadership Skills and Change Management MBA 18 SML 832 Labour Law and Compensation Management MBA 19 SML 833 Human Resources Planning Sem. Subject LC L T P WC CR CYL 110 MAL110 AML110 CSL101 CYP 100 HUL101 I Chemistry: Concepts and Applications Mathematics-I Mechanics Introduction to Computers and Programming Chemistry Laboratory English in Practice-I PHL 110 MAL 120 EEL 101 MEL 120 MEL110 PHP100 HUL II Fields and Waves Mathematics-II Fundamentals of Electrical Manufacturing Practices Graphic Science Physics Laboratory Communication Skills EEL 201 EEL 202 EEL 203 EEL 205 EEP 201 EEP 203 HUL235 III Digital Electronic Circuits Circuit Theory Electromechanics Signals and Systems Electronics Laboratory - I Electromechanics Laboratory English (Technical Communication) EEL 204 MAL250 EEL 301 EEP 204 EEP 301 HUL 234 EEL210 IV Analog Electronics Circuits Probability theory and stochastic Control - I Electronics Laboratory - II Control Laboratory Language and Communication Circuit Analysis V EEL 303 CSL 201 EEL 306 EEL 325 EEP 303 HUL 242 EEL310 EEL P a g e

97 Power - I Data Structures Communication Control - II Power Laboratory Soft Skills & Personality Development Control Theory Electrical Machines EEL 209 EEL 308 EEP 308 EEL 456 EEP 209 HUL 300 SML 101 VI Power Electronics Devices and Circuits Computer Architecture Computer Technology Laboratory Power - II Power Electronics lab Communication Skills & Personality Development MANAGEMENT CONCEPTS EET 420 PRACTICAL TRAINING (EE) EEC 420 EEL 305 EEL 451 EEP 305 EEP 451 SML 115 SML 312 SML 721 SML 105 VII Colloquium (EE) Electric Drives Power Systems Protection Drives Lab Power Systems Protection Lab MANAGERIAL ECONOMICS ORGANIZATIONAL BEHAVIOR Corporate Business Environment ACCOUNTING FOR MANAGERS EEL 452 EEL 453 EED 421 SML 760 SML 705 SML731 SML 895 VIII HVDC Transmission Power System Dynamics and Control Major Project Part 1 (EE) MARKETING MANAGEMENT Financial Management Human Resource Management Management of Research Methodology Summer MBA Summer Trainning EED 422 SML 732 SML 801 SMD 700 IX Major Project Part 2(EE) Business Strategy Business Ethics and Corporate Governance MBA 14 MBA 15 MBA 16 Summer Training Project report SML 203 SMD 800 X Business Law MBA 17 MBA 18 MBA 19 Management Thesis P a g e

98 The overall credits structure: B.Tech.+MBA [ECE] The overall credits structure Undergraduate Core (UC) Undergraduate Elective (UE) Program Core (PC) Program Elective (PE) Category Credits Category Credits Category Credits Category Credits DC 62.5 DE 37 MC 52 ME 24 BS 19 HU & HM 17 EAS 17 OC 10 Total 98.5 Total 64 Over all Credits Total Credits Basic Sciences (BS) Core Code Subject Name L T P Total CYL110 Chemistry: Concepts and Applications CYP100 Chemistry Laboratory P a g e

99 MAL110 Mathematics I MAL120 Mathematics II PHL110 Field & Waves PHP100 Physics Laboratory Arts and Sciences (EAS) Core Code Subject Name L T P Total AML110 Mechanics CSL101 Introduction to Computers & Programming EEL101 Fundamentals of Electrical MEL110 Graphic Science MEL120 Manufacturing Practices Humanities and Social Sciences (HC) Core Code Subject Name L T P Total HUL 101 English in Practice-I HUL110 Communication Skills HUL235 English (Technical Communication) HUL234 Language & Communication HUL242 Soft Skills & Personality Development HUL300 Communication Skills & Personality Development S No Subject Credits Code Name Category L T P TOTAL 1 EEL205 Signals and Systems DC EEL202 Circuit Theory DC EEL201 Digital Electronic Circuits DC EEP201 Electronics Lab-I DC P a g e

100 5 EEL204 Analog Electronics Circuits DC EEL301 Control Engg-1 DC EEP204 Electronics Lab-II DC MAL250 Prob Soch proc. DC EEP301 Control Engg lab DC EEL207 Engg Electromagnetics DC EEP307 Electromagnetics Lab DC EEL306 Comm. Engg. DC EEP306 Comm. Engg Laboratory DC EEL441 Industrial Electronics DC EEL318 Microprocessor DC EEL322 Integrated Circuits Technology DC EEL329 VLSI Technology and Design DC EEL338 Antennas and Propagation DC EED421 Major Project Part-I DC EEP205 Signal Processing Lab-1 DC EEL334 Wireless Communication DC EET420 Practical Training(ECE) DC S No 100 P a g e Subject Credits Code Name Category L T P TOTAL 1 CSL201 Data structures DE EEL308 Computer Architecture DE EEL358 Operating Systems DE EEL321 Digital Hardware Designs DE EEL442 OP-Amps and Linear Integrated circuits DE EEL316 Digital Comm. DE

101 7 EEL713 Microwave Theory and Circuits DE EEL319 Digital Signal Processing DE EEC420 Colloquium (ECE) DE EED412 Major Project Part 2 (ECE) DE List of Open Core for Minor Degree (Communication ) Subject Credits S No Code Name L T P TOTAL 1 EEL208 Electronic devices & Circuits EEL313 Signals System EEL314 Communication Theory EEL333 Communication Theory-II EEL336 Advanced Signal Processing EEL434 Optical Communication EEL474 Antenna Fundamentals EEL436 Mobile Communication EEL471 Telecommunication and Switching Networks List of Open Core for Minor Degree( Integrated Electronics &Circuits ) Subject Credits S No Code Name L T P TOTAL 1 EEL208 Electronic devices & Circuits EEL343 Integrated Circuits EEL345 Digital System Design EEL347 CMOS VLSI Design EEL336 Advanced Signal Processing EEL439 Operational Amplifier P a g e

102 7 EEL429 Microelectronic Circuits EEL476 Analog Mixed Signal Ics EEL475 Telecommunication and Switching Networks Subject MBA Core (MC) Credits Code Name Category L T P TOTAL SML 101 Management Concepts MC SML115 MANAGERIAL ECONOMICS MC SML312 ORGANIZATIONAL BEHAVIOR MC SML721 Corporate Business Environment MC SML105 ACCOUNTING FOR MANAGERS MC SML760 MARKETING MANAGEMENT MC SML705 Financial Management MC SML731 Human Resource Management MC SML895 Management of Research Methodology MC SML732 Business Strategy MC SML801 Business Ethics and Corporate Governance MC SMD700 Summer Training Project MC SML203 Business Law MC SMD800 Management Thesis MC P a g e MBA Electives (ME) Marketing Elective

103 Subject Credits Code Name Category L T P TOTAL SML 761 Consumer Behavior MBA SML 762 Service Marketing MBA SML 763 Retail Management MBA SML 811 Industrial Marketing MBA SML 812 Sales and Distribution Management MBA SML 813 SML 873 SML 876 Advertising, Brand, Media Management Security Analysis and Investment Management Project Appraisal Planning and Control Finance Elective MBA MBA MBA SML 877 Banking Service Operations MBA SML 821 Portfolio Management and Mutual Funds MBA SML 822 Management of Financial Services MBA SML 823 Advanced Management Accounting MBA HR Elective SML 735 Training and Development MBA SML 736 SML 737 SML 831 SML 832 Performance Management and Reward System Strategic Human Resource Management. Leadership Skills and Change Management Labour Law and Compensation Management MBA MBA MBA MBA SML 833 Human Resources Planning MBA P a g e

104 Sem. LC L T P WC CR I II III IV CYL 110 MAL110 AML110 CSL101 CYP 100 HUL101 Chemistry: Concepts and Applications Mathematics -I Mechanics Introduction to Computers and Programming Chemistry Laboratory English in Practice-I PHL 110 MAL 120 EEL 101 MEL 120 MEL110 PHP100 HUL110 Fields and Waves Mathematics -II Fundamenta ls of Electrical Manufacturing Practices Graphic Science Physics Laboratory Communicatio n Skills EEL 201 EEL 202 CSL 201 EEL 205 EEP 201 HUL235 English Digital Circuit Data Signals and Electronics (Technical Electronic Theory Structure Systems Laboratory - I Communicatio Circuits n) EEL 204 MAL 250 EEL 301 EEP 204 EEP 301 EEL 207 HUL 234 EEP 307 Analog Electronics Circuits Probability theory and stochastic Control - I Electronics Laboratory - II Control Laboratory Electromagne tics Language and Communicatio n Electromagne tics Lab OC V EEL 306 EEL 321 EEL 308 EEL 442 EEP 306 EEP 205 HUL 242 Communicati on VI Digital Hardware Design Computer Architecture OP-AMPS & Linear Integrated Circuits Communicati on Laboratory Signal Processing Laboratory-I Soft Skills & Personality Development EEL441 EEL 318 EEL 316 EEL 713 HUL 300 SML 101 Communicatio Digital Microwave Industrial Microproces n Skills & MANAGEMEN Communica Theory & Electronics sor Personality T CONCEPTS tion Circuits Development OC-2 OC P a g e

105 250. ECT 420 PRACTICAL TRAINING (EP) VII VIII Sum mer IX EEL 338 EED 421 EEL 319 EEC 420 SML 115 SML 312 SML 721 SML 105 Antennas & Propagation Major Project Part 1 (ECE) Digital Signal Processing Colloquium( ECE) MANAGERIAL ECONOMICS ORGANIZATIO NAL BEHAVIOR Corporate Business Environment ACCOUNTI NG FOR MANAGER S EEL 329 EEL 334 EED 412 SML 760 SML 705 SML731 SML 895 VLSI Technology & Design Wireless Communicati on Major Project Part 2 (ECE) MARKETING MANAGEMENT Financial Management Human Resource Management Managemen t of Research Methodolog y MBA Summer Trainning EED 422 SML 732 SML 801 SMD 700 Major Project Part 2(ECE) Business Strategy Business Ethics and Corporate Governance MBA 14 MBA 15 MBA 16 Summer Training Project report SML 203 SMD X Business Law MBA 17 MBA 18 MBA 19 Managemen t Thesis P a g e

106 23 The overall credits structure: B.Tech.+MBA [ME] The overall credits structure OC 10 EAS 18 MBA CORE 40 DE 37 HU & HM 21 MBA ELECTIVE 18 DC 75 MBA (Core+ Elective) 58 BS 19 TOTAL 238 Basic Sciences (BS) Core L T P Total CYL110 Chemistry: Concepts and Applications CYP100 Chemistry Laboratory MAL110 Mathematics I MAL120 Mathematics II PHL110 Field & Waves PHP100 Physics Laboratory Arts and Sciences (EAS) Core L T P Total AML110 Mechanics CSL101 Introduction to Computers & Programming EEL101 Fundamentals of Electrical MEL110 Graphic Science MEL120 Manufacturing Practices Humanities and Social Sciences (HC) Core L T P Total HUL 101 English in Practice-I HUL110 Communication Skills HUL235 English (Technical Communication) HUL234 Language & Communication HUL242 Soft Skills & Personality Development HUL300 Communication Skills & Personality Development List of Department core ( DC) Course Code Course Name L T P Credit MEL140 Thermodynamic AML160 Mechanics of Fluids MEL211 Kinematics and Dynamics of Machines AML140 Mechanics of Solids AMP261 Solids Laboratory AMP262 Fluids Laboratory MEP201 Mechanical Drawing MEL241 Energy Conversion MEL236 Material Science P a g e

107 MEL232 Casting, Welding and Forming MAL230 Numerical Methods MEL221 Operations Research MEL242 Heat and Mass Transfer MEL311 Machine Element Design MEL233 Machining, Machine Tools and Metrology MEL312 Mechanical Measurement, Control Theory & Applications MEP341 Thermal Laboratory MEL322 Operations Planning and Control MEL410 Practical Training MEC410 Colloquium MED411 Major Project Part MEL421 Production Management MEL425 Flexible Manufacturing Systems Departmental Electives (DE) Course Code Course Name L T P Credit MED310 Mini Project (ME) MEL310 Concurrent MEL314 Noise MEL316 Mechanical Vibrations MEL321 Ergonomics MEL332 Design and Manufacturing of Composites MEL333 Metrology MEL334 Low Cost Automation MEL341 Gas Dynamics and Propulsion MEL342 Power Plant Technologies MEL343 Fuels, Combustion and Pollution MEL344 Refrigeration and Air-Conditioning MEL345 Internal Combustion Engines MEL346 Turbo-machinery MEL410 Creativity in MEL411 Mechatronics MEL412 Advanced Mechanical Design MEL413 Design of Mechanisms MEL414 Computer Aided Mechanical Design MEL415 Vibrations Design MEL416 Robotics MEL417 Lubrication MEL420 Total Quality Management MEL422 Project Management MEL425 Flexible Manufacturing Systems MEL431 CNC Machines and Programming MEL432 Microprocessor Applications in Manufacturing MEL433 Micro- and Nano- Manufacturing MEL434 Design for Manufacturing and Assembly MEL435 Geometric Modelling for Manufacturing MEL436 Injection Moulding and Mould Design MEL441 Modelling and Experiments in Heat Transfer MEL442 Thermal Analysis of Bio-systems MEL716 Nano Scale Heat Transfer P a g e

108 MED412 Major Project Part 2 (ME) P a g e

109 MBA Electives (ME) Marketing Elective MBA 14 SML 761 Consumer Behavior MBA 15 SML 762 Service Marketing MBA 16 SML 763 Retail Management MBA 17 SML 811 Industrial Marketing MBA 18 SML 812 Sales and Distribution Management MBA 19 SML 813 Advertising, Brand, Media Management Finance Elective MBA 14 SML 873 Security Analysis and Investment Management MBA 15 SML 876 Project Appraisal Planning and Control MBA 16 SML 877 Banking Service Operations MBA 17 SML 821 Portfolio Management and Mutual Funds MBA 18 SML 822 Management of Financial Services MBA 19 SML 823 Advanced Management Accounting HR Elective MBA 14 SML 735 Training and Development MBA 15 SML 736 Performance Management and Reward System MBA 16 SML 737 Strategic Human Resource Management MBA 17 SML 831 Leadership Skills and Change Management MBA 18 SML 832 Labour Law and Compensation Management MBA 19 SML 833 Human Resources Planning P a g e

110 Sem LC L T P WC CR. I II III IV V VI VII VIII IX AML110 Mechanics (3-0-2) 4 MEL 120 Manufacturing Practice (2-0-4) 4 MEL 140 Thermodynamics MEL236 Material Science MEL242 Heat & Mass Transfer MEL312 Mechanical Measurement, Control Theory & Applications (3-1-2) 5 DE-3 (MEL342) Power Plant Technologies MED411 Major Project (0-0-12) 6 CSL101 Introduction to Computers & Programming (3-0-2) 4 EEL 101 Fundamentals of Electrical (3-0-2) 4 AML160 Mechanics of Fluids MEL232 Casting, Welding & Forming (3-0-2) 4 MEL311 Machine Element Design (3-1-2) 5 MEP341 Thermal Laboratory (0-0-3) 1.5 DE-4 (MEL425) Flexible Manufacturing Systems (3-0-0) 3 MED310 Mini Project (ME) (0-0-8) 4 DE-7 MEL434 Micro- and Nano- Manufacturing (3-0-2) 4 CYL110 Chemistry: Concepts & Applications PHL 110 Fields & Waves MEL 211 Kinematics & Dynamics of Machines (3-0-2) 4 MAL230 Numerical Methods MEL233 Machining, Machine Tools & Metrology (3-0-2) 4 DE-1 (MEL344) Refrigeration & Air Conditioning MEC410 Colloquium (ME) (0-3-0) 3 DE-5 (MEL316) Mechanical Vibrations (3-0-2) 4 SML 732 Business Strategy CYP100 Chemistry Laboratory (0-0-4) 2 PHP 100 Physics Lab (0-0-4) 2 AML140 Mechanics of Solids MEL221 Operations Research MEL241 Energy Conversion MEL322 Operations Planning & Control (3-0-0) MEL421 Production Management DE-6 (MEL420) Total Quality Management SML 801 Business Ethics and Corporate Governance MAL110 Mathematics I MAL120 Mathematics I MEP 201 Mechanical Drawing (1-0-3) 2.5 DE-2 (MEL345) I.C. Engine AMP262 Fluids Laboratory (0-0-3) 1.5 OC-2 (3-0-0) 3 MET410 Practical Training (ME) SML115 Managerial Economics SML 760 Marketing Management SML312 Organizati onal Behavior SML 705 Financial Managem ent MBA-SUMMER TRANING MBA-14 MBA-15 ENV101 Environmental Studies (0-0-0) 0 MEL110 Graphics Science (2-0-4) 4 AMP261 Solids Laboratory (0-0-3) 1.5 OC-1 (3-0-0) 3 OC-3 SML 101 Management Concepts (3-0-0)3 SML721 Corporate Business Environment SML 731 Human Resource Management MBA-16 HUL 101 English in Practice-I (2-0-2) 3 HUL 110 Communication Skills (2-0-2) 3 HUL235 English (Technical Communication) (2-1-0) 3 HUL234 Language & Communication HUL242 Soft Skills & Personality Development HUL300 Communication Skills & Personality Development SML105 Accounting for Managers SML 895 Management of Research Methodology SMD 700 Summer Training Project (0-0-4) P a g e

111 X DE-8 MEL436 Injection Moulding and Mould Design (2-0-4) 4 SML 203 Business Law (3-0-0)3 MBA-17 MBA-18 MBA-19 SMD 800 Management Thesis (0-0-4) P a g e

112 24 The overall credits structure: M. Tech. [Part Time] Computer Science & (I-Semester) S.No. Subject Subject Code (L-T-P) Credits 1 Introduction to Logic and Functional Programming CSL765 (3-0-0) 3 2 Data Structures and Algorithms CSL630 (3-0-0) 3 3 Advanced Computer Networks CSL724 (3-0-2) 4 4 Software System Laboratory CSP701 (0-0-6) 3 (II-Semester) Total 13 1 Modern Parallel Programming CSL730 (3-0-2) 4 2 Cloud Computing CSL839 (3-0-2) 4 3 Cryptography andcomputer Security CSL759 (3-0-2) 4 (III-Semester) Total 12 1 Cluster and Grid Computing CSL841 (3-0-2) 4 2 Independent Study (MCS) CSS799 (0-3-0) 3 3 Internet Technologies EEL855 (3-0-0) 3 (IV-Semester) Total 10 1 Special Topics in Parallel Computation CSL860 (3-0-0) 3 2 Minor Project CSD745 (0-1-6) 4 (V-Semester) Total 7 1 Major Project Part 1 (MCS) CSD893 (0-0-12) 6 (VI-Semester) Total 6 1 Major Project Part 2 (MCS) CSD894 (0-0-24) 12 Total 12 S.No. Subject Digital Communication (I-Semester) Subject Code (L-T-P) 1 CAD of RF and Microwave Devices CRL711 (3-0-2) 4 2 Signal Theory EEL711 (3-0-0) 3 3 Communication Laboratory-I EEP717 (0-0-4) 2 (II-Semester) Credits Total 9 1 RF and Microwave Measurement System Techniques CRL724 (3-0-0) 3 2 RF MEMS Design and Technology CRL726 (3-0-0) 3 3 Power from Renewable and Environment Impacts ESL736 (3-0-0) 3 4 RF and Microwave Measurement Laboratory CRP718 (0-0-6) 3 (III-Semester) Total P a g e

113 1 Digital Communication EEL762 (3-0-2) 4 2 Digital Signal Processing-1 EEL731 3 Communication Laboratory-II EEP719 (0-0-4) 2 Total 10 (IV-Semester) 1 Architectures and Algorithms for DSP Systems CRL702 (2-0-4) 4 2 Independent Study (CRF) CRS735 (0-3-0) 3 3 Minor Project CSD745 (0-1-6) 4 Total 11 (V-Semester) 1 Major Project Part 1 (CRF) CRD811 (0-0-12) 6 Total 6 (VI-Semester) 1 Major Project Part 2 (CRF) CRD812 (0-0-24) 12 Total 12 S.No. Subject Power System (I-Semester) Subject Code (L-T-P) 1 Power System Analysis EEL791 (3-0-0) 3 2 Power System Protection EEL792 (3-0-0) 3 3 EHV AC Transmission EEL885 (3-0-0) 3 (II-Semester) Credits Total 9 1 Power System Control and Instrumentation EEL796 2 Flexible AC Transmission System EEL894 (3-0-0) 3 3 Power System Optimization EEL896 (3-0-0) 3 (III-Semester) Total 10 1 High Voltage DC Transmission EEL794 2 Selected Topics in Power System EEL891 (3-0-0) 3 3 Power System Laboratory EEP798 (0-0-4) 2 (IV-Semester) Total 9 1 Load forecasting and Load Management EEL897 2 Power from Renewable and Environment Impacts ESL736 (3-0-0) 3 2 Minor Project (EES) EED790 (0-1-6) 4 (V-Semester) Total 11 3 OE-1 -- (3-0-0) 3 1 Major Project Part 1 (EES) EED890 (0-0-12) 6 (VI-Semester) Total 9 1 Major Project Part 2 (EES) EED898 (0-0-24) 12 Total P a g e Structure

114 (I-Semester) S.No. Subject Subject Code (L-T-P) Credits 1 Advanced Structural Analysis CEL717 (3-0-0) 3 2 Structural Dynamics CEL719 (3-0-0) 3 3 Design of Concrete Structures CEL721 (3-0-0) 3 Total 9 (II-Semester) 1 Earthquake Analysis and Design CEL724 2 Finite Element Method in Structural CEL733 3 Design of Tall Buildings CEL832 (2-1-0) 3 Total 11 (III-Semester) 1 Advanced Design of Bridges CEL729 2 Design of Steel Structures CEL718 (2-1-0) 3 3 Design of industrial Structures CEL727 Total 12 (IV-Semester) 1 PE OE-2 -- (3-0-0) 3 3 Independent Study CES820 (0-3-0) 3 Total 10 (V-Semester) 1 Major Project Part 1 (CES) CED821 (0-0-12) 6 Total 6 (VI-Semester) 1 Major Project Part 2 (CES) CED822 (0-0-24) 12 Total 12 Integrated Electronics & Circuits (I-Semester) S.No. Subject Subject Code (L-T-P) Credits 1 Microelectronics EEL732 (3-0-0) 3 2 MOS VLSI EEL734 (3-0-0) 3 3 VLSI Design EEL834 (3-0-0) 3 4 RF MEMS Design and Technology CRL726 (3-0-0) 3 12 (II-Semester) 1 Analog Integrated Circuits EEL782 (3-0-0) 3 2 IC Technology EEL784 (3-0-2) 4 3 Biomedical Electronics EEL736 (3-0-0) 3 Total 10 (III-Semester) 1 Digital Signal Processing-1 EEL731 (3-0-2) 4 2 Computer Aided VLSI Design EEL832 (3-0-2) 4 3 IEC Laboratory EEP735 (0-0-6) 3 Total 11 (IV-Semester) 114 P a g e

115 1 OE-1 -- (3-0-0) 3 2 OE-2 -- (3-0-0) 3 3 Independent Study (EEN) EES837 (0-3-0) 3 Total 9 (V-Semester) 1 Major Project Part 1 (EEN) EED888 (0-0-12) 6 Total 6 (VI-Semester) 1 Major Project Part 2 (EEN) EED889 (0-0-24) 12 Total 12 Thermal (I-Semester) S.No. Subject Subject Code (L-T-P) Credits 1 Advanced Thermodynamics MEL703 (3-0-0) 3 2 Experimental Methods in Thermal MEL705 (2-0-4) 4 3 Viscous Fluid Flows AML715 (3-0-0) 3 Total 10 (II-Semester) 1 Convection Heat and Mass Transfer MEL802 (3-0-0) 3 2 Radiation and Conduction Heat Transfer MEL804 (3-0-0) 3 3 Thermal Systems Simulation and Design MEL806 (3-0-2) 4 Total 10 (III-Semester) 1 Applied Mathematics for Mechanical Engineers MEL707 (2-0-2) 3 2 Advanced Power Plant Cycles MEL712 (3-0-2) 4 3 Thermal and Nuclear Steam Power Plants MEL714 (3-0-2) 4 Total 11 (IV-Semester) 1 Refrigeration and Air Conditioning Technologies MEL711 (3-0-2) 4 2 Independent Study (Thermal ) MES810 (0-3-0) 3 3 Design Project (Thermal ) MED700 (0-1-6) 4 Total 11 (V-Semester) 1 Major Project Part 1 (Thermal ) MED811 (0-0-12) 6 Total 6 (VI-Semester) 1 Major Project Part 2 (Thermal ) MED812 (0-0-24) 12 Total The overall credits structure: M.Tech. [Full Time] Computer Science & (I-Semester) S.No. Subject Subject Code (L-T-P) Credits 1 Introduction to Logic and Functional Programming CSL765 (3-0-0) 3 2 Data Structures and Algorithms CSL630 (3-0-0) P a g e

116 3 Advanced Computer Networks CSL724 (3-0-2) 4 4 Power from Renewable and Environment Impacts ESL736 (3-0-0) 3 5 Software System Laboratory CSP701 (0-0-6) 3 Total 16 (II-Semester) 1 Modern Parallel Programming CSL730 (3-0-2) 4 2 Digital Image Analysis CSL783 (3-0-2) 4 3 Cryptography andcomputer Security CSL759 (3-0-2) 4 4 Internet Technologies EEL855 (3-0-0) 3 5 Minor Project CSD745 (0-1-6) 4 Total 19 (III-Semester) 1 Cluster and Grid Computing CSL841 (3-0-2) 4 2 Cloud Computing CSL839 (3-0-2) 4 3 Major Project Part 1 (MCS) CSD893 (0-0-12) 6 Total 13 (IV-Semester) 1 Major Project Part 2 (MCS) CSD894 (0-0-24) 12 Total 12 Digital Communication (I-Semester) S.No. Subject Subject Code (L-T-P) Credits 1 CAD of RF and Microwave Devices CRL711 (3-0-2) 4 2 Digital Communication EEL762 (3-0-2) 4 3 Signal Theory EEL711 (3-0-0) 3 4 Digital Signal Processing-1 EEL731 (3-0-0) 3 5 Communication Laboratory-I EEP717 (0-0-4) 2 (II-Semester) 1 RF and Microwave Measurement System Techniques CRL724 2 Architectures and Algorithms for DSP Systems CRL702 (2-0-4) 4 3 RF MEMS Design and Technology CRL726 (3-0-0) 3 4 Power from Renewable and Environment Impacts ESL736 (3-0-0) 3 5 RF and Microwave Measurement Laboratory CRP718 (0-0-6) 3 (III-Semester) 16 Total 17 1 Adaptive Filter Theory CRL734 2 Communication Laboratory-II EEP719 (0-0-4) 2 3 Independent Study (CRF) CRS735 (0-3-0) 3 4 Major Project Part 1 (CRF) CRD811 (0-0-12) 6 (IV-Semester) Total 15 1 Major Project Part 2 (CRF) CRD812 (0-0-24) 12 Total P a g e

117 Integrated Electronics & Circuits (I-Semester) S.No. Subject Subject Code (L-T-P) Credits 1 Microelectronics EEL732 (3-0-0) 3 2 MOS VLSI EEL734 (3-0-0) 3 3 VLSI Design EEL834 (3-0-0) 3 4 RF MEMS Design and Technology CRL726 (3-0-0) 3 12 (II-Semester) 1 Analog Integrated Circuits EEL782 (3-0-0) 3 2 IC Technology EEL784 (3-0-2) 4 3 Biomedical Electronics EEL736 (3-0-0) 3 4 Independent Study (EEN) EES837 (0-3-0) 3 5 IEC Laboratory EEP735 (0-0-6) 3 Total 16 (III-Semester) 1 Digital Signal Processing EEL731 (3-0-2) 4 2 Computer Aided VLSI Design EEL832 (3-0-2) 4 3 Special Module in Low Power IC Design EEV833 (3-0-0) 3 4 Major Project Part 1 (EEN) EED888 (0-0-12) 6 Total 17 (IV-Semester) 1 OE-2 -- (3-0-0) 3 2 Major Project Part 2 (EEN) EED889 (0-0-24) 12 Total 15 Power System (I-Semester) S.No. Subject Subject Code (L-T-P) Credits 1 Power System Analysis EEL791 (3-0-0) 3 2 Power System Protection EEL792 (3-0-0) 3 3 EHV AC Transmission EEL885 (3-0-0) 3 4 Power from Renewable and Environment Impacts ESL736 (3-0-0) 3 5 Power System Laboratory EEP798 (0-0-4) 2 14 (II-Semester) 1 Power System Control and Instrumentation EEL796 2 Flexible AC Transmission System EEL894 (3-0-0) 3 3 Power System Optimization EEL896 (3-0-0) 3 4 Load forecasting and Load Management EEL897 5 Minor Project (EES) EED790 (0-1-6) 4 Total P a g e

118 (III-Semester) 1 High Voltage DC Transmission EEL794 2 Selected Topics in Power System EEL891 (3-0-0) 3 3 Nature Inspire Algoritms for Solving Optimization Problems EEL893 (3-0-0) 3 4 Major Project Part 1 (EES) EED890 (0-0-12) 6 Total 16 (IV-Semester) 1 Major Project Part 2 (EES) EED898 (0-0-24) 12 Total 12 Structure (I-Semester) S.No. Subject Subject Code (L-T-P) Credits 1 Advanced Structural Analysis CEL717 (3-0-0) 3 2 Structural Dynamics CEL719 (3-0-0) 3 3 Design of Concrete Structures CEL721 (3-0-0) 3 4 Design of Tall Buildings CEL832 (2-1-0) 3 12 (II-Semester) 1 Design of Steel Structures CEL718 (2-1-0) 3 2 Solid Mechanics in Structural CEL722 3 Earthquake Analysis and Design CEL724 4 Finite Element Method in Structural CEL733 5 Structural Laboratory CEP726 (0-1-6) 4 Total 19 (III-Semester) 1 Advanced Design of Bridges CEL729 2 Design of industrial Structures CEL727 3 Major Project Part 1 (CES) CED821 (0-0-12) 6 Total 14 (IV-Semester) 1 Independent Study CES820 (0-3-0) 3 2 Major Project Part 2 (CES) CED822 (0-0-24) 12 Total 15 Thermal (I-Semester) S.No. Subject Subject Code (L-T-P) Credits 1 Advanced Thermodynamics MEL703 (3-0-0) 3 2 Experimental Methods in Thermal MEL705 (2-0-4) 4 3 Applied Mathematics for Mechanical Engineers MEL707 (2-0-2) 3 4 Viscous Fluid Flows AML715 (3-0-0) 3 5 Refrigeration and Air Conditioning Technologies MEL711 (3-0-2) 4 17 (II-Semester) 1 Convection Heat and Mass Transfer MEL802 (3-0-0) 3 2 Radiation and Conduction Heat Transfer MEL804 (3-0-0) P a g e

119 3 Thermal Systems Simulation and Design MEL806 (3-0-2) 4 4 Design Project (Thermal ) MED700 (0-1-6) 4 Total 14 (III-Semester) 1 Advanced Power Plant Cycles MEL712 (3-0-2) 4 2 Thermal and Nuclear Steam Power Plants MEL714 (3-0-2) 4 3 Major Project Part 1 (Thermal ) MED811 (0-0-12) 6 Total 14 (IV-Semester) 1 Independent Study (Thermal ) MES810 (0-3-0) 3 2 Major Project Part 2 (Thermal ) MED812 (0-0-24) 12 Total P a g e

120 26 The overall credits structure: Polytechnic [Civil] Year Subject L T P WC CR I CSL 104 HUL 104 EEP 109 PHL 102 CYL 102 MAL 104 Computer & AML 106 MEP 107 MEP 108 English & Electrical & Applied Applied Applied Information Applied Workshop Communication Electronics Physics Chemistry Mathematics Technology Mechanics Drawing Practice Skills Workshop (3 0 2) 4 (2 0 2) 3 (3 1 0) 4 Fundamentals (2 1 2) 4 (0 0 4) 2 (0 0 3) 2 (1 0 2) 2 (0 0 3) 2 (2 0 2) II III DCE 201 Strength of Materials (2 1 1) 3.5 DCE 301 Theory of Structure (2 1 0) 3 DCE 202 Fluid Mechanics (2 1 1) 3.5 DCE 302 Design of Steel Structure (2 1 0) 3 DCE 203 Building Technology (2 1 0) 3 DCE 303 Design of R.C.C. Structure (2 1 0) 3 DCE 204 Surveying- I (2 0 2) 3 DCE 304 Surveying II (2 1 1) 4.5 DCE 205 Transportation (2 1 1) 3.5 DCE 305 Water Supply & Sanitary (2 0 2) 3 DCE 206 Soil & Foundation (2 0 2) 3 DCE 306 Irrigation (2 1 0) 3 DCE 207 Concrete Technology (2 0 2) 3 DCE 307 Civil Estimating & Costing (211) 3.5 DCE 208 Building Drawing (0 0 2) 1 DCE 308 Environmental (1 1 0) 2 DCE 209 Construction Materials & Equipments (2 1 1) 3.5 DCE 309 Construction Management and Accounts (1 1 0) 2 DCE 210 Computer Aided Drawing (0 0 2) 1 DCE 310 Earthquake Resistant Structure (1 1 0) The overall credits structure: Polytechnic [CSE] Year L T P WC CR I HUL 104 English & Communicatio n Skills (1 0 2) 2 PHL 102 Applied Physics (3 0 2) 4 CYL 102 Applied Chemistry (2 0 2) 3 MAL 104 Applied Mathematic s (3 1 0) 4 CSL 104 Computer & Information Technology Fundamental s (2 0 2) 3 AML 106 Applied Mechanics (2 1 2) 4 MEP 107 Drawing (0 0 4) 2 EEP 109 Electrical & Electronics Workshop (0 0 3) 1 MEP 108 Workshop Practice (0 0 3) II DCS 201 Programming and Problem Solving Through 'C' (2 0 2) 3 DCS 202 Computers System Architecture (2 1 0) 3 DCS 203 Operating System Principles (2 0 0) 2 DCS 204 Basics of Electronic Devices and Circuits (2 1 0) 3 DCS 205 Basics of Digital Electronics (2 0 2) 3 DCS 206 Data Communicatio n (2 0 0) 2 DCS 207 Data Base Managemen t System (2 1 0) 3 DCS 208 Microprocess or and Interfacing (2 0 2) 3 DCS 209 Internet and Web Technologies (2 0 2) 3 DCS 210 PC Maintenance and Trouble Shooting (2 0 2) III DCS 301 Data Structure & Algorithm (2 0 2) 3 DCS 302 Object Oriented Programmin g Through C++ (2 0 2) 3 DCS 303 Unix, Shell Programming and Administratio n (2 0 2) 3 DCS 304 Software (2 0 0) 2 DCS 305 Dot Net Technology (2 0 2) 3 DCS 306 Computer Network (2 0 0) 2 DCS 307 Data warehouse and mining (2 1 0) 3 DCS 308 Introduction to Network Security and Cryptography (2 0 0) 2 DCS 309 Java Tools (2 0 2) 3 DCS 310 PHP & MySql (2 0 2) P a g e

121 121 P a g e

122 27 The overall credits structure: Polytechnic [EE] Year L T P WC CR I HUL 104 English & Communication Skills (1 0 2) 2 PHL 102 Applied Physics (3 0 2) 4 CYL 102 Applied Chemistry (2 0 2) 3 MAL 104 Applied Mathematics (3 1 0) 4 CSL 104 Computer & Information Technology Fundamentals (2 0 2) 3 AML 106 Applied Mechanics (2 1 2) 4 MEP 107 Drawing (0 0 4) 2 EEP 109 Electrical & Electronics Workshop (0 0 3) 2 MEP 108 Workshop Practice (0 0 3) II DEE 201 Basic Electronics (2 0 1) 3 DEE 202 Basic Mechanical (2 0 1) 3 DEE 203 Basic Electrical (2 0 1) 3 DEE 204 Electrical Measurement & Instr. (2 0 2) 3 DEE 205 Electrical Circuit Theory (2 1 0) 3 DEE 206 Electrical Machines I (2 1 2) 4 DEE 207 Power System I (2 1 0) 3 DEE 208 Microprocessor & C- Programming (2 0 1) 3 DEE 209 Electrical Workshop (2 0 2) 3 DEE 210 Management (2 0 0) III DEE 301 Power Electronics & Drives (2 0 1) 3 DEE 302 Utilization of Electrical Power & Traction (2 0 0) 2 DEE 303 Estimating, Costing & Design of Electrical Installations (2 0 1) 3 DEE 304 Electrical Design & Drawing (2 0 2) 3 DEE 305 Fundamentals of Control System (2 1 0) 3 DEE 306 Electrical Machines II (2 1 2) 4 DEE 307 Power System II (2 1 0) 3 DEE 308 Power System III (2 0 0) 2 DEE 309 Switchgear & Protection (2 1 0) 3 DEE 310 Energy Management (2 0 0) The overall credits structure: Polytechnic [ECE] Year Subject L T P WC CR I II III 122 P a g e HUL 104 English & Communication Skills (1 0 2) 2 DEL 201 Electronic Components & Shop Practice ( 2 0 2) 3 DEL 301 Electronic Circuits (2 0 2) 3 PHL 102 Applied Physics (3 0 2) 4 DEL 202 Circuit Analysis (2 1 0) 3 DEL 302 Advance Microprocess or & Microcontrolle r (2 0 2) 3 CYL 102 Applied Chemistry (2 0 2) 3 DEL 203 Electronic Measuremen t & Instr. (2 0 2) 3 DEL 303 Advance Communicati on System (2 0 2) 3 MAL 104 Applied Mathematics (3 1 0) 4 DEL 204 Electronic Devices & Circuits (2 0 2) 3 DEL 304 Microwave & Optical Fiber (2 1 0) 3 CSL 104 Computer & Information Technology Fundamentals (2 0 2) 3 DEL 205 Digital Electronics (2 0 2) 3 DEL 305 Power & Industrial Electronics (2 0 2) 3 AML 106 Applied Mechanics (2 1 2) 4 DEL 206 Wave Propagation & Comm. Engg. (2 0 1) 3 DEL 306 Biomedical Instrumentati on (2 0 2) 3 DEL 207 Microprocess or (2 0 2) 3 DEL 307 Linear Integrated Circuits & Design (2 0 2) 3 MEP 107 Drawing (0 0 4) 2 DEL 208 Audio & Video System (2 0 1) 3 DEL 308 Telecommunic ation & Switching Networks (2 0 0) 2 EEP 109 Electrical & Electronics Workshop (0 0 3) 2 DEL 209 Electronic Instruments (2 0 1) 3 DEL 309 Computer Communicati on (2 0 0) 2 MEP 108 Workshop Practice (0 0 3) 2 DEL 210 C- Programming (2 0 1) 3 DEL 310 Management & Entrepreneurs hip (2 0 0)

123 29 The overall credits structure: Polytechnic [ME] Year Subject L T P WC CR I HUL 104 English & Communication Skills (1 0 2) 2 PHL 102 Applied Physics (3 0 2) 4 CYL 102 Applied Chemistry (2 0 2) 3 MAL 104 Applied Mathematics (3 1 0) 4 CSL 104 Computer & Information Technology Fundamentals (2 0 2) 3 AML 106 Applied Mechanics (2 1 2) 4 MEP 107 Drawing (0 0 4) 2 EEP 109 Electrical & Electronics Workshop (0 0 3) 2 MEP 108 Workshop Practice (0 0 3) II DME 201 Strength of Materials (2 1 1) 4 DME 202 Fluid Mechanics & Machines (2 1 1) 4 DME 203 Materials and Processes (2 0 1) 4 DME 204 Theory Of Machines (2 1 0) 3 DME 205 Machine Drawing and Computer Aided Drafting (0 0 4) 2 DME 206 Basic Automobile (2 0 1) 3 DME 207 Electrical & Electronics (2 0 1) 3 DME 208 Thermodynamics & I.C. Engines (2 0 1) 3 DME 209 Workshop Technology & Metrology (2 0 2) 3 DME 210 C Programming (2 0 2) III DME 301 Refrigeration and Air Conditioning (2 0 2) 3 DME 302 Processes In Manufacturing (2 0 2) 3 DME 303 Thermal & Heat Transfer (2 0 2) 3 DME 304 CNC Machines & Automation (2 0 2) 3 DME 305 Power Generation (2 0 0) 2 DME 306 Advance Workshop Techniques (2 0 2) 3 DME 307 Industrial (2 0 0) 2 DME 308 Machine Design (2 1 0) 3 DME 309 Mechanical Estimating & Costing (2 1 0) 3 DME 310 Management & Entrepreneurship (2 0 0) P a g e

124 30 The overall credits structure BCA+MCA Semester Course Code Course Title L T P Credit 124 P a g e I MAL 112 Mathematical Foundation for Computer Science I CSL 107 Fundamentals Of Computers & Information Technology I CSL 103 Introduction to Programming Using C I SML 101 Managements Concepts I CSL 106 PC Packages & PC Software Lab I HUN 106 Business Communication II MAL 126 Algebra & Differential Equations II CSL 251 Internet & E-Commerce II CSL 221 Data Structures Using C II CSL 231 Visual Programming Basics & Lab II CSL 241 Management Information System II HUL 101 English In Practice III CSL-271 Database Management Systems III CSL-272 Operating Systems III CSL-273 System Analysis and Design III CSL-274 Object Orient Programming using C III MAL-225 Statistics for BCA III CSD-281 Minor Project in Visual Basic IV CSL 261 Computer Organization and Architecture IV MAL 280 Operation Research IV CSL 424 Data Communication & Computer Networks IV CSL 442 Web Technology IV CSL 436 Introduction to Software IV CSL 432 Programming in Java V CSL-782 Computer Graphics & Multimedia V CSL-548.Net Programming using VB.net

125 125 P a g e V CSL-449 Software Quality Management V CSL-759 Cryptography and Network Security V CSL-545 Enterprise Resource Planning V CSL-546 Information Security and Cyber Laws VI CSL-620 Unix and Shell Programming CSL-608 Data Ware House and Data Mining VI 4 CSL-607 Information Storage System VI 3 CSL-605 Advanced Java VI 6 CSL-606 Soft Computing VI 4 VI CSD-675 Major Project work Industrial Training (8 week) VII CSL 105 Discrete Mathematics VII SML 103 Accounting and Financial Management VII MAL 160 Numerical and Statistical Methods VII CSL-705 Theory of computation VII CSL-770 E-Commerce VII CSD-704 Industrial Training Report VIII CSL 306 Principles of Programming Languages VIII CSL 671 AI & Expert Systems VIII CSL724 Advance Computer Networks VII CSL-752 Principles of Compiler Design VIII CSD-740 Seminar - Research Paper VIII CSP 338 PPL Lab IX CSL-874 Advanced Java programming IX CSL-875 Web Technologies with PHP IX Elective I IX Elective II IX CSP-876 Advanced Java Lab

126 IX CSP-877 PHP Lab X CSD-897 Project(Industrial) & Viva- Voce Examination BCA+MCA [Proposed Scheme] Sem. Subject LC L T P WC CR. I II III IV V VI VII VIII MAL 112 Mathematical Foundation for Computer Science MAL 126 Algebra & Differential Equations CSL-271 Database Management Systems CSL 261 Computer Organization & Architecture CSL-583 Computer Graphics & Multimedia (3-1-4) 6 CSL-620 Unix & Shell Programming (3-0-4) 5 MAL 160 Numerical & Statistical Methods CSL 306 Principles of Programming Languages CSL 107 Fundamentals of Computers & Information Technology CSL 251 Internet & E-Commerce CSL-272 Operating Systems MAL 280 Operation Research CSL-548.Net Programming using VB.net (3-1-4) 6 CSL-608 Data Ware House and Data Mining CSL 105 Discrete Mathematics CSL-752 Principles of Compiler Design CSL 103 Introduction to Programming Using C (3-1-4) 6 CSL 221 Data Structures Using C (3-1-2) 5 CSL-273 System Analysis & Design CSL 424 Data Communication & Computer Networks CSL-449 Software Quality Management CSL-607 Information Storage System (3-0-0) 3 SML 103 Accounting & Financial Manag. CSL 671 AI & Expert Systems SML 101 Managements Concepts CSL 231 Visual Programming Basics & Lab (3-1-4) 6 CSL-274 Object Orient Programming using C++ (3-1-4) 6 CSL 442 Web Technology (3-1-4) 6 CSL-759 Cryptography & Network Security CSL-606 Soft Computing CSL-705 Theory of computation CSL 724 Advanced Computer Networks CSL 106 PC Packages & PC Software Lab (3-1-4) 6 CSL 241 Management Information System MAL-225 Statistics for BCA CSL 436 Introduction to Software CSL-545 Enterprise Resource Planning CSD-675 Major Project work (0-0-8) 4 CSL-770 E-Commerce (4-0-0) 4 CSP 338 PPL Lab (0-4-0) 2 HUN 106 Business Communication (2-0-0)2 HUL 101 English In Practice (2-0-2)3 CSD-281 Minor Project in Visual Basic (0-0-4) 2 CSL 432 Programming in Java (3-1-4) 6 CSL-546 Information Security Z& Cyber Laws CSL-605 Advanced Java (3-1-4)6 CSD 704 Industrial Training Report (0-1-2) CSD-740 Seminar - Research Paper (0-0-4) P a g e

127 IX CSL-874 Advanced Java programming CSL-875 Web Technologies with PHP Elective I Elective II CSP-876 Advanced Java Lab (0-0-4)2 CSP-877 PHP Lab (0-0-4) X CSD-897 Project(Industrial) & Viva- Voce Exam (0-0-0) The overall credits structure BCA Semester Course Code Course Title L T P Credit 127 P a g e I MAL 112 Mathematical Foundation for Computer Science I CSL 107 Fundamentals Of Computers & Information Technology I CSL 103 Introduction to Programming Using C I SML 101 Managements Concepts I CSL 106 PC Packages & PC Software Lab I HUN 106 Business Communication II MAL 126 Algebra & Differential Equations II CSL 251 Internet & E-Commerce II CSL 221 Data Structures Using C II CSL 231 Visual Programming Basics & Lab II CSL 241 Management Information System II HUL 101 English In Practice II CSL243 Multimedia and Animation III CSL-271 Database Management Systems III CSL-272 Operating Systems III CSL-273 System Analysis and Design III CSL-274 Object Orient Programming using C III MAL-225 Statistics for BCA III CSD-281 Minor Project in Visual Basic

128 IV CSL 261 Computer Organization and Architecture IV MAL 280 Operation Research IV CSL 424 Data Communication & Computer Networks IV CSL 442 Web Technology IV CSL 436 Introduction to Software IV CSL 432 Programming in Java IV CSL437 Client Server Technology V CSL-583 Computer Graphics & Multimedia Programming V CSL-548.Net Programming using VB.net V CSL-449 Software Quality Management V CSL-759 Cryptography and Network Security V CSL-545 Enterprise Resource Planning V CSL-546 Information Security and Cyber Laws VI CSL-620 Unix and Shell Programming CSL-608 Data Ware House and Data Mining VI 4 CSL-607 Information Storage System VI 3 CSL-605 Advanced Java VI 6 CSL-606 Soft Computing VI 4 VI CSD-675 Major Project work BCA [Proposed Scheme] Sem. Subject LC L T P WC I II MAL 112 Mathematical Foundation for Computer Science MAL 126 Algebra &Differential Equations 128 P a g e CSL 107 Fundamentals of Computers & Information Technology CSL 251 Internet & E- Commerce CSL 103 Introduction to Programming Using C(3-1-4) 6 CSL 221 Data Structures Using C (3-1-2) 5 SML 101 Managements Concepts CSL 231 Visual Programming Basics & Lab CSL 106 PC Packages & PC Software Lab (3-1-4) 6 CSL 241 Management Information System HUN 106 Business Communication (2-0-0)2 HUL 101 English In Practice (2-0-2)3 CSL 243 Multiedia and Animation (4-0-2)

129 (3-1-4) 6 III IV V VI CSL-271 Database Management Systems CSL 261 Computer Organization & Architecture CSL-782 Computer Graphics & Multimedia (3-1-4) 6 CSL-620 Unix & Shell Programming (3-0-4) 5 CSL-272 Operating Systems MAL 280 Operation Research CSL-548.Net Programming using VB.net (3-1-4) 6 CSL-608 Data Ware House and Data Mining CSL-273 System Analysis and Design CSL 424 Data Communication & Computer Networks CSL-449 Software Quality Management CSL-607 Information Storage System (3-0-0) 3 CSL-274 Object Orient Programming using C++(3-1-4) 6 CSL 442 Web Technology (3-1-4) 6 CSL-759 Cryptography and Network Security CSL-606 Soft Computing MAL-225 Statistics for BCA CSL 436 Introduction to Software CSL-545 Enterprise Resource Planning CSD-675 Major Project work (0-0-8) 4 CSD-281 Minor Project in Visual Basic (0-0-4) 2 CSL 432 Programming in Java (3-1-4) 6 CSL-546 Information Security and Cyber Laws CSL-605 Advanced Java (3-1-4)6 CSL 437 Client Server Technology (3-0-0) P a g e

130 34 The overall credits structure MCA Semester Course Code Course Title L T P Credit 130 P a g e I CSL 120 Programming in C I CSL 716 Discrete Mathematics I CSL 761 Computer Organization and Architecture I SML 103 Accounting and Financial Management I MAL 160 Numerical and Statistical Methods I CSL 281 Management Information System I CSP 105 C Language LAB I HUL 108 Technical Communication Practices II CSL 630 Data Structures and Algorithms II CSL 305 Database Management System II CSL 306 Principles of Programming Languages II CSL 373 Operating Systems II MAL 280 Operations Research II CSP 320 Data Structures Lab II CSP 330 Operating System Lab II HUL 217 Communicative English III CSL-705 Theory of computation III CSL-782 Graphics and Multimedia Programming III CSL-740 Software III CSL-752 Principles of Compiler Design III CSL-760 Object Oriented Programming Analysis and Design III CSL-770 E-Commerce III CSP-746 C++ Lab III CSL-740 Graphics & Multimedia Lab Using C III CSD-740 Seminar - Research Paper IV CSL 712 Internet and Java Programming

131 DE Courses IV CSL 424 Data Communication & Computer Networks IV CSL 786 Software Architecture, Testing & Quality Assurance IV CSL 671 AI & Expert Systems IV CSL 582 Visual Programming usnig.net IV CSP 782 Java Programming Lab IV CSP 784 Visual Programming Lab IV CSD 850 Minor project in java/.net V CSL-874 Advanced Java programming V CSL-875 Web Technologies with PHP V CSL-759 Cryptography and Computer Security V Elective I V Elective II V CSP-876 Advanced Java Lab V CSP-877 PHP Lab VI CSD-897 Project(Industrial) & Viva- Voce Examination S. No. Subject L T P C 1 CSL-836 Mobile Communication (Elective -1) CSL-870 Distributed Computing (Elective -1) CSL-889 Application Development with Android (Elective -2) CSL-783 Digital Image Analysis (Elective -2) CSL-842 Cluster and Grid Computing (Elective -3) CSL-894 Advanced.NET with AJAX and MVC (Elective -3) P a g e

132 132 P a g e

133 35 MCA [Proposed Scheme] Sem. Subject LC L T P WC CR. I MAL 160 Numerical & Statistical Methods CSL 716 Discrete Mathematics CSL 120 Programming in C CSL 761 Computer Organization &Architecture CSL 281 Management Information System CSP 105 C Language LAB (0-0-4)2 HUL 108 Technical Communicatio n Practices (2-0-0)2 SML 103 Accounting and Financial Management II III IV V VI MAL 280 Operations Research CSL-705 Theory of computatio n CSL 712 Internet and Java Programmi ng CSL-874 Advanced Java programmin g CSD-897 Project(Indu strial) & Viva- Voce Examinatio n (0-0-0) 20 CSL 630 Data Structures &Algorithms CSL-782 Graphics and Multimedia Programming CSL 424 Data Communication & Computer Networks CSL-875 Web Technologies with PHP CSL 305 Database Management System CSL-740 Software CSL 786 Data Software Architecture, Testing & Quality Assurance CSL-759 Cryptography & Computer Security CSL 306 Principles of Programming Languages CSL-752 Principles of Compiler Design CSL 671 AI & Expert Systems Elective I CSL 373 Operating Systems CSL-760 Object Oriented Programming Analysis and Design CSL 582 Visual Programming using.net Elective II CSP 320 Data Structures Lab (0-0-4)2 CSL-770 E-Commerce (4-0-0) 4 CSP 782 Java Programming Lab (0-0-4)2 CSP-876 Advanced Java Lab (0-0-4)2 CSP 330 Operating System Lab (0-0-4)2 CSP-746 C++ Lab (0-0-4)2 CSP 784 Visual Programming Lab (0-0-4)2 CSP-877 PHP Lab (0-0-4)2 HUL 217 Communicativ e English (2-0-2)3 CSP-740 Graphics & Multimedia Lab Using C++ (0-0-4)2 CSL-620 Unix & Shell Programming (3-0-4) 5 CSD-740 Seminar - Research Paper (0-1-2)2 CSL-621 Analysis and Design of Algorithm (3-0-0) 3 CSD 850 Minor project in java/.net (0-0-4) P a g e

134 36 The overall credits structuremba Sem. Subject LC L T P WC CR. I CSL 702 Computer Application in Management (3-0-2) 4 HUL 103 Business Communication (2-0-0) 2 MAL 215 Mathematical Statistics for Management Decision SML 101 Management Concepts SML 105 Accounting For Managers SML 115 Managerial Economics SML 312 Organization Behaviour SML 760 Marketing Management II SML 705 Financial Management SML 794 Communication Skills & Personality Development (2-0-2) 3 MAL 280 Operation Research SML 731 Human Resources Management SML 895 Management of Research Methodology SML 745 Operation Management SML 850 Management of Information Technology SML 721 Corporate Business Environment III SML 732 Business Strategy SML 302 Entrepreneurship Development SMD 700 Project Report ( 0-0-4) 2 Elective - 1 Elective - 2 Elective IV SML 801 Business Ethics & Corporate Governance SML 203 Business Law SMD 800 Management Thesis ( 0-0-4) 2 Elective - 1 Elective - 2 Elective P a g e

135 37 The overall credits structure BBA Sem. Subject LC L T P WC CR. I CSL 108 Fundamentals Of Computers (3-0-2) 4 HUL 103 Business Communication (2-0-0) 2 MAL 101 Business Mathematics SML 101 Management Concepts SML 105 Accounting For Managers SML 115 Managerial Economics II SML 201 Introduction to Business Environment HUL 103 English in Practice (2-0-2) 3 SML 202 Business Statistics SML 203 Business Law SML 204 Cost Analysis & Control SML 205 Business Ethics III SML 308 Management Accounting HUL 305 Soft Skill Lab 1 (2-0-2) 3 SML 312 Organsiation Behaviour SML 309 Production Planning & Control SML 302 Entrepreneurship Development SML 325 Strategic Management IV CSL 241 Management Information System MAL 280 Operation Research SML 412 Financial Management in Industry SML 413 Marketing Management in Industry SML 414 Human Resources Management in Industry SML 415 Research Methodology in Industry V SML 505 Supply Chain Management SML 501 International Business SML 502 Project Management (4-1-0) 5 SML 513 Total Quality Management (4-1-0) 5 SMD 500 Project Report ( 0-0-4) 2 Elective - 1 (4-1-0) 5 Elective - 2 (4-1-0) 5 Elective - 3 (4-1-0) VI SML 601 Fundamental of Leadership SML 602 Indian Economy SML 603 Export, Import Policy & Documentation (4-1-0) 5 SML 604 Insurance & Risk Management (4-1-0) 5 Elective - 1 (4-1-0) 5 Elective - 2 (4-1-0) 5 Elective - 3 (4-1-0) P a g e

136 38 The overall credits structure B.Com. Sem. Subject LC L T P WC CR. I II III CSL 108 Fundamentals of Computers (3-0-2) 4 SML 201 Introduction to Business Environment SML 308 Management Accounting HUL 103 Business Communication (2-0-0) 2 HUL 103 English in Practice (2-0-2) 3 HUL 305 Soft Skill Lab 1 (2-0-2) 3 MAL 101 Business Mathematics SML 202 Business Statistics SML 312 Organization Behaviour SML 101 Management Concepts SML 203 Business Law SML 310 Corporate Accounting SML 105 Accounting for Managers SML 204 Cost Analysis & Control SML 302 Entrepreneurship Development SML 115 Managerial Economics SML 205 Business Ethics SML 311 Income Tax IV CSL 241 Management Information System MAL 280 Operation Research SML 412 Financial Management in Industry SML 413 Marketing Management in Industry SML 414 Human Resources Management in Industry SML 415 Research Methodology in Industry V SML 503 Indirect Taxation (4-1-0) 5 SML 501 International Business SML 502 Project Management (4-1-0) 5 SML 504 Auditing SMD 500 Project Report (0-0-4) 2 SML 512 Banking Concept & Practice (4-1-0) 5 SML 511 Security Analysis & Portfolio Management (4-1-0) VI SML 605 E-Commerce SML 602 Indian Economy SML 603 Export, Import Policy & Documentation (4-1-0) 5 SML 604 Insurance & Risk Management (4-1-0) 5 SML 611 Indian Financial System (4-1-0) 5 SML 612 International Financial Management (4-1-0) P a g e

137 39 The overall credits structure: Department Elective BBA S. No. Code Subject L T P C 5 th Semester (Elective -1 Finance ) 1 SML 511 Security Analysis & Portfolio Management SML 512 Banking Concept & Practice (Elective -2 HR ) 3 SML 531 Strategic Management of Human Resources SML 532 Approaches to Human Resources Development (Elective -3 Marketing ) 3 SML 521 Service Industry in India SML 522 Retail Practice in India th Semester (Elective -1 Finance) 1 SML611 Indian Financial System SML 612 International Financial Management (Elective -2 HR ) 3 SML 623 Labour Law & Industrial Relation SML 624 Leadership Management (Elective -3 Marketing ) 3 SML 621 Industrial Marketing Concept & Practice SML 622 Advertisement Management P a g e

138 The overall credits structure: Department Elective MBA S. No. Code Subject L T P C 3rd Semester (Elective -1 Finance ) 1 SML 873 Security Analysis and Investment Management SML 876 Project Appraisal Planning and Control SML 877 Banking Service Operations (Elective -2 HR ) 4 SML 735 Training and Development SML 736 Performance Management and Reward System SML 737 Strategic Human Resource Management (Elective -3 Marketing ) 7 SML 761 Consumer Behavior SML 762 Service Marketing SML 763 Retail Management th Semester(Elective -1 Finance ) 1 SML 821 Portfolio Management and Mutual Funds SML 822 Management of Financial Services SML 823 Advanced Management Accounting (Elective -2 HR ) 4 SML 831 Leadership Skills and Change Management SML 832 Labour Law and Compensation Management SML 833 Human Resources Planning (Elective -3 Marketing ) 7 SML 811 Industrial Marketing SML 812 Sales and Distribution Management SML 813 Advertising, Brand, Media Management S. No. OC-1 OC-2 OC-3 OC-4 OC-5 OC-6 OC-7 List of Open Core for Minor Degree( Integrated Electronics &Circuits ) Subject Code Subject Name L-T-P Credits SML 211 Concept & Practice of Business Management SML 331 Business Environment and Corporate Strategy SML 332 Management Accounting and Financial Management SML 431 Organization and Human Resource Management SML 432 Business Law SML 451 Entrepreneurship & Management SML 452 Financial Markets OC-8 SML 491 Fundamental of Marketing Management OC-9 SML 492 Business Ethics & Corporate Social Responsibility P a g e

139 40 The overall credits structure: BBA+ MBA Sem. Subject LC L T P WC CR. I CSL 108 Fundamentals Of Computers (3-0-2) 4 HUL 103 Business Communication (2-0-0) 2 MAL 101 Business Mathematics SML 101 Management Concepts SML 105 Accounting For Managers SML 115 Managerial Economics II SML 201 Introduction to Business Environment HUL 103 English in Practice (2-0-2) 3 SML 202 Business Statistics SML 203 Business Law SML 204 Cost Analysis & Control SML 205 Business Ethics III SML 308 Management Accounting HUL 305 Soft Skill Lab 1 (2-0-2) 3 SML 312 Organization Behaviour SML 309 Production Planning & Control SML 302 Entrepreneurs hip Development SML 325 Strategic Management IV CSL 241 Management Information System MAL 280 Operation Research SML 412 Financial Management in Industry SML 413 Marketing Management in Industry SML 414 Human Resources Management in Industry SML 415 Research Methodology in Industry V SML 505 Supply Chain Management SML 501 International Business SML 502 Project Management (4-1-0) 5 SML 513 Total Quality Management (4-1-0) 5 SML 541 IT in Management (3-0-2) 4 SML 542 Business Policy & Strategy VI SML 601 Fundamental of Leadership SML 602 Indian Economy SML 603 Export, Import Policy & Documentation (4-1-0) 5 SML 604 Insurance & Risk Management (4-1-0) 5 SML 641 Personality Development (2-0-2) 3 SML 642 Managerial Effectiveness (3-0-0) VII SML 751 Event Management SML 752 Real Estate Management SML 753 Corporate Tax Planning SML 754 Education Management SML 755 Management Control System SML 756 Marketing Research SML 757 Hospitality Management SML 758 Health Care Management P a g e

140 VIII SMD 600 Summer Training for 6 month IX Elective - 1 Elective - 2 Elective X Elective - 1 Elective - 2 Elective - 3 SMD 900 Dissertation Report ( 0-0-4) P a g e

141 41 The overall credits structure: B.Com. + MBA I II III IV V VI CSL 108 Fundamentals of Computers (3-0-2) 4 SML 201 Introduction to Business Environment SML 308 Management Accounting CSL 241 Management Information System SML 503 Indirect Taxation (4-1-0) 5 SML 605 E-Commerce HUL 103 Business Communication (2-0-0) 2 HUL 103 English in Practice (2-0-2) 3 HUL 305 Soft Skill Lab 1 (2-0-2) 3 MAL 280 Operation Research SML 501 International Business SML 602 Indian Economy MAL 101 Business Mathematics SML 202 Business Statistics SML 312 Organsiation Behaviour SML 412 Financial Management in Industry SML 502 Project Management (4-1-0) 5 SML 603 Export, Import Policy & Documentation (4-1-0) 5 SML 101 Management Concepts SML 203 Business Law SML 310 Corporate Accounting SML 413 Marketing Management in Industry SML 504 Auditing SML 604 Insurance & Risk Management (4-1-0) 5 SML 105 Accounting For Managers SML 204 Cost Analysis & Control SML 302 Entrepreneurship Development SML 414 Human Resources Management in Industry SML 541 IT in Management (3-0-2) 4 SML 641 Personality Development (2-0-2) 3 SML 115 Managerial Economics SML 205 Business Ethics SML 311 Income Tax SML 415 Research Methodology in Industry SML 542 Business Policy & Strategy (4-1-0) 5 SML 642 Managerial Effectiveness VII SML 751 Event Management SML 752 Real Estate Management SML 753 Corporate Tax Planning SML 754 Education Management SML 755 Management Control System SML 756 Marketing Research SML 757 Hospitality Management SML 758 Health Care Management VIII SMD 600 Summer Training for 6 month IX Elective - 1 Elective - 2 Elective X Elective - 1 Elective - 2 Elective - 3 SMD 900 Dissertation Report ( 0-0-4) P a g e

142 42 The overall credits structure: Department Elective BBA+MBA and B.Com+MBA S. No. Code Subject L T P C 9 th Semester (Elective -1 Finance ) 1 SML 873 Security Analysis and Investment Management SML 876 Project Appraisal Planning and Control SML 877 Banking Service Operations (Elective -2 HR ) 4 SML 735 Training and Development SML 736 Performance Management and Reward System SML 737 Strategic Human Resource Management (Elective -3 Marketing ) 7 SML 761 Consumer Behavior SML 762 Service Marketing SML 763 Retail Management th Semester(Elective -1 Finance ) 1 SML 821 Portfolio Management and Mutual Funds SML 822 Management of Financial Services SML 823 Advanced Management Accounting (Elective -2 HR ) 4 SML 831 Leadership Skills and Change Management SML 832 Labour Law and Compensation Management SML 833 Human Resources Planning (Elective -3 Marketing ) 7 SML 811 Industrial Marketing SML 812 Sales and Distribution Management SML 813 Advertising, Brand, Media Management P a g e

143 43 Course Overview (Civil) B.Tech, B.Tech+M.Tech, B.Tech.+ MBA The details of every course are given in this section. Information about each course includes number, credits, L-T- P structure, pre-requisites, overlapped courses and course contents. For more information contact the course coordinator or head of department/ Program coordinator. CEL100 Earth and Earth Processes Environmental crisis, Earth as a closed system, Limitations of earth resources. Earth resources: Geologic Cycle, Minerals, Rocks, Soils, Water, Wind and Ice. Hazardous processes and mitigation: River flooding and fluvial processes, Volcanic activity, Earthquakes and related phenomena including seismic microzonation, Mass movements and land slides, Marine activity and coastal erosion. Soil resources: Problematic soils, Regional distribution, Erosion, Contamination of soils and ground water and remediation, Land reclamation. Rockmasses and stability: In-situ stresses, Discontinuities, Weathering, Tunnel collapses and Rock bursts. Mining and impact: Blasting, Subsidence, Mine fills and wastes. Waste disposal: Nuclear waste repositories. Land evaluation. CEL110 Basic Concepts in Sustainable Development 4 credits (3-1-0) Introduction; Basic characteristics of pollution and receiving environment; Concepts in sustainability; Contaminants and fate of contaminants; Noise Pollution, Sustainability and Bioenvironment, ISO Series. CEN110 Introduction to Civil 2 credits (0-0-4) Introductory lectures, demonstrations, field visits on activities of department and the Civil Profession. CEL120 Pollution Prevention and Control Legislative Framework for Environmental Management; Introduction to pollution: Sources, types, characteristics and impacts. Prevention versus control of pollution: Environmentally sound technology management; Tools for clean production: reuse, recycle, recovery, source reduction, raw material substitution, toxic use reduction and process modifications. Voluntary environmental programs: life cycle analysis; environmental cost accounting; use of a business-friendly, prevention-based approach; and the measurement of environmental performance, EIA. Urbanization and Sustainability, Environmental consequences of personal choices and examples of social marketing of more environmentally responsible consumption; Public Participation: Structure, Processes and Trends; Conflict Resolution. CEL140 Environmental Studies Energy & Environment basic concepts of energy resources, fossil fuel, geothermal, tidal, nuclear, solar, wind, hydropower & biomas. Ecology & Ecosystem Dynamics- ecosystem divercity, habitat classification. Type of ecosystems- wetlands, marshlands, swamps, lakes forest ecosystems- Tropical, Himalaya, sub-himalaya deserts, shelf ecosystem. Pollutant Sources and Controlair, water, solid waste and noise pollution and their control measures. Cleaner Production and Life Cycle Analysisreuse/recycle/recovery/ source reduction/raw material substitution. Basics of EIA and environmental audits, public participation in environmental decision making. LCA methodology, steps and tools. ISO 14000: new business paradigms: eco-industrial parks and eco labels. Emerging technologies for sustainable environmental management, Identification and evaluation of emerging environmental issues in air, water, wastewater and solid waste. Environment, Development and Society-comparative approaches to natural resource management: indigenous system of natural resource management-land, water, forest, air etc: environmental ethics. Urbanization and Sustainability, Environmentally responsible consumption. Environmental psychology, Environmental perceptions and attitudes, Coping with environmental stress in built environment. CEP200 Design Concepts in Civil 2 credits (0-0-4) Design concepts in Structural, Design concepts in Water Resources, Design Concepts in Transportation, Design Concepts in Environmental, Design concepts in Geotechnical. CEL212 Environmental 4 credits (3-0-2) Water supply: Sources, Water demand and forecasting. Quality of water, water borne diseases, standards, water quality index. Unit Processes: Systems and unit processes of water purification. Water distribution networks. Wastewater : Systems of sanitation, wastewater flows, Collection and conveyance of wastewater, layout systems. Characteristics and microbiology of wastewater. BOD kinetics. Disposal of treated wastewater on land and in water. Unit processes for wastewater treatment; Sludge management, introduction to solids and hazardous waste management, air and noise pollution and control. CEL222 Geology and Soil Mechanics 5.5 credits (3-1-3) Pre-requisites: AML110 Geology: Introduction; Dynamic Earth; Materials of Earth; Silicate Structures and Symmetry Elements; Formations of Rocks; Characterisation; Weathering Processes; Geological Work Landforms; Formation of Soils; Geological Time Scale; Structural 143 P a g e

144 Features; Tectonics; Stress Distribution; Earthquakes; Geological Maps and Air Photos; Ground Water. Soil Mechanics: Origin and Classification of Soils; Phase relationships; Effective Stress Principle; Effective Stress Under Hydrostatic and 1D flow; Permeability; Compressibilty; Consolidation; Terzaghi s 1D Consolidation Theory; Shear Strength; Drainage Conditions; Pore Water Pressure; Mohr s Circle; Failure Envelope and Strength Parameters; Factors Affecting Shear Strength; Laboratory: Geological Mapping contouring, topo sheets, outcrops, apparent and true dips, three point problems, depth, thickness, joints, faults; Megascopic and Microscopic identification of Minerals and Rocks. Visual Soil Classification; Water Content; Atterberg Limits; Grain Size Analysis; Specific Gravity; Permeability; Introduction to consolidation and strength apparatus; Guided tour through representative geological formations and structures. CEL231 Structural Analysis I 5 credits (3-1-2) Pre-requisites: AML110 Introduction to structures, loading and modeling. Internal forces in statically determinate structures plane and space trusses, beams, frames, arches and cables. Deflection of statically determinate structures moment area method, conjugate beam method, virtual work method. Static and Kinematic indeterminacy of structures. Force method of analysis of indeterminate structures including temperature changes and lack of fit. Analysis of rolling loads. Influence lines for statically determinate and indeterminate structures. CEL232 Concrete Material and Design 6 credits (3-1-4) Pre-requisites: AML110 Chemistry: properties and types of cement; Properties of aggregates and fresh concrete; Concrete Mix Design; Properties of hardened concrete; Reinforcing steel. Design Philosophy: Working stress and limit state design concepts; Design of R.C. beam Sections in flexure, shear, torsion and bond; Design for serviceability; Design of R.C. beams; Design of one way and two way R.C. Slabs; Design of R.C. short and long columns; Design of R.C. footings. CEL241 Transportation I 4 credits (3-0-2) Transportation Systems and their classification and description. Role of Roads, Road Transport and Planning in India. Road User and the Vehicle. Geometric Design: Horizontal Alignment, Vertical Alignment, Cross-section Elements. Highway Project Preparation: Surveys and Investigations. Pavements: Types of Pavements, Flexible and Rigid pavement Analysis and Design, Overlay Design. Road Construction Materials. Highway Maintenance. Traffic : Traffic Characteristics, Fundamental relationships, theories of traffic flow, shock waves, intersection design and traffic signs and signals - design, Highway Capacity. CEL251 Hydrology and Hydraulics 6 credits (3-1-4) Pre-requisites: AML110 Open Channel Flow: Channel Characteristics and parameters, Uniform flow, Critical flow, Specific Energy concepts, Gradually Varied Flows, Rapidly Varied flow with special reference to hydraulic jump. Boundary Layer Theory: Navier Stokes Equation, Boundary Layer Equation in 2-dimensions, Boundary layer characteristics, Integral Momentum equation, onset of turbulence, properties of turbulent flow, skin friction, drag, lift and circulation. Pipe Flow: Laminar and Turbulent flow in Smooth and Rough pipes, pipe network analysis, Losses inpipes.hydrologic Cycle, Processes and Applied Methodologies: Rainfall,Evapotranspiration, Infiltration, Streamflow; Unit Hydrographs, Flood Routing and Frequency Analysis; Occurrence of Groundwater and Groundwater Flow. CEL271 Elements of Surveying 3 credits (2-0-2) Introduction to Surveying, Instruments of Leveling, Theodolites and Plane-tables. Measurement of Distances, directions and elevations by different methods. Traversing. Vertical control, Precise levelling, Trigonometric levelling. Mapping of details and contouring. Measurement of areas, volumes. Application of above measurements in quantity computations. Errors of measurements and their adjustments. Curve setting: simple circular curves, compound and reverse curves. Introduction to GPS, Differential GPS. CED310 Mini Project (CE) 3 credits (0-0-6) Design/fabrication/implementation work under the guidance of a faculty member. Prior to registration, a detailed plan of work should be submitted by the student to the Head of the Department for approval. CEL311 Advanced Water and Wastewater 4 credits (3-0-2) Pre-requisites: CEL212 Water purification: Theory, operation and design: Settling tanks, tube settlers, Coagulation and flocculation - Orthokinetic and Perikinetic, Slow and rapid sand filters. Methods, Theory and application of disinfection: chlorine, ozone, UV, Solar etc. Adsorption kinetics in water treatment. Design of water treatment plants; Wastewater characteristics, Wastewater Treatment: Theory, operation and design of aerobic (activated sludge and its variations, trickling filter, RBC and Oxidation ponds and ditches), anaerobic (anaerobic digestion, UASBR, anaerobic filter, lagoons); Secondary settling tanks. Tertiary wastewater treatment: Removal of N, P, K and other trace elements. Sludge treatment and disposal. Design of wastewater treatment plants. Advanced wastewater treatment systems: Root zone technology, wetlands, Duckweeds, Membrane processes (RO, Ultra and Nano filtration, Ion Exchange). Centralized vs decentralized systems, low cost water and wastewater systems. Disposal of treated wastewater: 144 P a g e

145 Inland surface water, land for irrigation, marine coastal areas. CEL321 Geotechnical 5.5 credits (3-1-3) Pre-requisites: CEL222 Soils of India; properties of Natural and Compacted Soils; Flow Through Soils Laplace equation, flownets, seepage; Site Investigations; Foundations types, selection, design considerations, bearing capacity and settlement of shallow foundations; deep foundations; Slope Stability Analysis; Earth Dams types and design aspects; Earth Pressures and Retaining Structures; Properties of Rocks; Rock as Construction Material; Geological Site Criteria for Tunnels and Underground Structures, Dams, Rock Slopes and Landslides.Laboratory: Compaction, consolidation, sample preparation, vane shear test, direct shear test, unconfined compression test, unconsolidated undrained test, consolidated drained test, consolidated undrained test with pore water pressure measurement, direct shear test, drilling and sampling, field density, engineering properties of rocks, refraction and resistivity methods. CEL326 Geoenvironmental Sources of subsurface contamination and their effects; types of waste; integrated management of waste; transportation and disposal of solid waste on land; types of soils, permeability of soils, flow through soils, soil-waste interaction; ground water contamination; Waste containment principles; environmental control through liners, covers, leachate management and gas management; waste disposal in municipal solid waste landfills and in hazardous waste landfills; Waste disposal of coalash and mine tailings in ponds and mounds, of very hazardous waste in rocks in rocks; detection and monitoring of subsurface contamination; contaminated site characterization; control and remedial measures for contaminated sites; pollution control regulations. Pre-requisites: CEL231 Introduction to stability and buckling concepts; Structural steel and properties; Riveted, bolted and welded connections; Working stress and plastic design Methods; Design of tension, compression and flexural members (including built-up members); Column bases; Roof trusses. CEL338 Infrastructure Planning and Management Overview of the course, Infrastructure s impact on development of a country, Status of various sectors in Indian Infrastructure, Infrastructure Financing, Private Sector participation in infrastructure models, Basics of infrastructure planning, Problems in Infrastructure Development and Management. CEL339 Concrete Technology and Materials Cement Hydration: Cement Types, Paste Micro-structure; Workability; Durability; Factors affecting strength of concrete, Quality control; Concrete mix design; Types of concrete; Concrete production; Tests of concrete in structures; Failure criteria; Fracture mechanics; Hardening plasticity and fatigue; Creep and shrinkage; Fresh concrete modelling; Ionic diffusion in concrete. CEL341 Transportation II 4 credits (3-1-0) Pre-requisites: CEL241 Design of transportation facilities. (i) Rail Transport: location and route layout, section signals and intersections, earth work and pavement (track, stops, terminals, yard, parking etc.). (ii) Airports: Layout plan, terminal area, interconnection with other modes of transport, runways, Civil 150 circulation patterns, traffic controllers. (iii) Ports and other water transport technology belt conveyor and aerial transport: planning principles, operational requirements, Meglev, Hydrofoil, pipeline, etc. (iv) Transport Structure: FOBs, underground and multistoreyed parking, ramps, escalators, elevators, etc. CEL331 Structural Analysis II 5 credits (3-1-2) Pre-requisites: CEL231 Development of Slope-Deflection Equations of Equilibrium: Applications to Beams, frames undergoing user support settlement; Development of Moment Distribution Method; Distribution Factors; Application to Beams and Frames without side sway; Application to Frames with side sway; Beams and Frames with uneven loading; Support Settlement; Cases of Symmetry and anti symmetry; Strain energy method of analysis; Introduction to nature methods of analysis; Flexibility Method; Stiffness method; Direct Stiffness Methods for computer Application; Introduction to computer Software for Analysis. CEL332 Design of Steel Structures 5 credits (3-1-2) CEL351 Design of Hydraulic Structures 3 credits (2-0-2) Pre-requisites: CEL251 Input studies, canal layout, regime canal design, design concepts for irrigation structures on permeable foundations, energy dissipation devices, design of diversion works, gravity dam, cross drainage works, canal falls. CEL362 Construction Management 4 credits (3-1-0) Overview of the to the course, Linear programming, Problems in construction, Formulation, Graphical solution, Simplex method, Dual problem, sensitivity analysis and their application to Civil engineering, Transportation Assignment problems and their applications, Building Specifications, estimation and rate analysis. Project 145 P a g e

146 planning and network analysis, Time and cost control, Resource scheduling. CEC410 Colloquium (CE) 3 credits (0-3-0) Presentation by each student on his/her practical training and other topics specified by the course coordinator. CET410 Practical Training (CE) Non credit Practical Training of 50 working days in an Indian industry or R&D organization. CED411 Major Project Part 1 (CE) 3 credits (0-0-6) To set the objectives, deliverables, work plan, logistics planning and milestones with discernible outputs and then to demonstrate the feasibility through some initial work. CEL411 Industrial Waste Management Nature and characteristics of industrial wastes; Control and removal of specific pollutants in industrial wastewaters, i.e., oil and grease, cyanide. fluoride, toxic organics, heavy metals. Recent trends in industrial waste management; Prevention versus control of industrial pollution; Linkage between technology and pollution prevention; Tools for clean production, reuse, recycle, recovery, source reduction, raw material substitution, toxic use reduction and process modifications; Point, and area source: dispersion modeling of industrial air pollutants. Source reduction and control of industrial air pollution; Minimization of industrial solid and hazardous waste; Waste management case studies from various industries. CED412 Major Project Part 2 (CE) 7 credits (0-0-14) Pre-requisites: CED411 Preferably continuation of the topic of CED411. CEL412 Environmental Assessment Methodologies Environmental issues related to developmental activities: Nature and characteristics of environmental impacts of urban and industrial developments. Linkages between technology, environmental quality, economic gain, and societal goals. Environmental indices and indicators for describing affected environment. Methodologies and environmental systems modeling tools for prediction and assessment of impacts on environmental quality (surface water, ground water, air, soil). Monitoring and control of undesirable environmental implications. Environmental cost benefit analysis. Decision methods for evaluation of environmentally sound alternatives; Environmental health and safety: Basic concepts of environmental risk and definitions; Hazard identification procedures; Consequence analysis and modeling (discharge models, dispersion models, fire and explosion models, effect models etc.); Emerging tools for environmental management: Environmental Management Systems, Environmentally sound technology transfer, emission trading, international resource sharing issues, climate change, international environmental treaties and protocols. Case studies. CEL421 Ground Improvement 4 credits (3-0-2) Pre-requisites: CEL321 Compaction methods used in the laboratory and the field; shallow stabilization with cement, lime, flyash and other chemical admixtures; deep stabilization using vibroflotation, compaction piles, dynamic compaction, blasting, sand drains, stone columns, lime and cement columns; Grouting by permeation, displacement and jet methods; functions and applications of geosynthetics geotextiles, geogrids, geomembranes; soil reinforcement using strips, bars and geosynthetics; soil nailing and ground anchors; dewatering techniques; Earthmoving machines and earthwork principles; piling and diaphragon wall construction; tunneling methods in soils; hydraulic barriers and containment systems for waste disposal in soils; control and remediation of soil contamination; Laboratory : Lab compaction methods light, heavy, kneading, vibratory- for soils and soils with admixtures; plasticity and undrained strength behaviour of compacted and stabilized clays; drained strength behaviour of compacted / stabilized sands. CEL422 Rock Pre-requisites: CEL321 Overlaps with: CEL651 Geological classification, rock and rock mass classification, strength and deformation behaviour of rocks, pore pressures, failure criteria, laboratory and field testing, measurement of in-situ stresses and strains, stability of rock slopes and foundations, design of underground structures, improvement of in situ properties of rock masses and support measures. CEL423 Design of Foundations, Earth and Earth Retaining Structures 4 credits (3-1-0) Pre-requisites: CEL321 Overlaps with: CEL610, CEL704, CEL708 Shallow Founations: Bearing Capacity: Bearing failure, Terminology; Empirical methods, Generalized bearing capacity theory, Layered soil, Foundations on or near slopes, Limit state design principles; Deep Foundations: Pile Foundations: Types and their selection, Ultimate load of individual piles in compressive, uplift, and lateral loading, Pile load tests, Downdrag, Pile groups. Caissons; Machine Foundations: Principles of vibrations, Types of machine foundations, Design criteria, Design of block foundations; 146 P a g e

147 Earth Dams: Components, Factors influencing design, Design of components; Earth Retaining Structures: Types, Earth pressure, Design of rigid, flexible and reinforced soil retaining walls, and braced excavations. CEL431 Advanced Structural Analysis 3 credits (2-0-2) Pre-requisites: CEL331 Introduction to FEM for structural analysis with review of energy methods 2D plane stress and plane strain elements, beam element, 2D bending element, example problems, elements of structural dynamics- free and forced vibration of SDOF system, treatment of impact and arbitrary loading, frequency and time domain analysis; free vibration mode ships and frequencies of MDOF systems; normal mode theory for forced vibration analysis of MDOF system; example problems. Elements of plastic analysis; upper and lower bound theorems; method of collapse mechanism; application to beams and multistory frames; example problems. Civil 151 CEL432 Design of Prestressed Concrete and Industrial Structures 4 credits (3-0-2) Pre-requisites: CEL232 & CEL331 Prestressed Concrete Structures Fundamentals of prestressing, Prestressing technology, Analysis of prestressed members, Prestress losses, Design for Flexure, Design for shear and torsion, Design of anchorage Zones in post-tensioned members. Industrial Structures- Analysis and design of Cylindrical shell structures, Folded plates, Chimneys, Silos, Bunkers. CEL433 Advanced Structural Design 4 credits (3-0-2) Pre-requisites: CEL232 & CEL332 Design of Reinforced Cement concrete (RCC) Structures Building frames, Liquid retaining structures, Earth retaining walls, Flat slabs, Staircases.Design of Steel Structures Plate girders, gantry girders and steel bridge components. CEL442 Traffic and Transportation Planning 3 credits (2-1-0) Pre-requisites: CEL241 Transportation System, Random utility theory, Supply and demand, Flow estimation and modeling, Planning and engineering evaluation, Transportation engineering management, Traffic flow theory and management, Air and water navigational control, Rehabilitation and satellite area accessibility, Network and graph theory application. CEL443 Transportation Safety and Environment 3 credits (3-0-0 Multidisciplinary approach to planning for traffic safety and injury control; precrash, crash and post crash models; roles of vehicle, roadway, traffic, driver, and environment, crash and injury causations; Mixed traffic flow; Transport related pollution; Technology Vision-2020; Urban and nonurban traffic noise sources, Noise level factors, Noise pollution; Energy related ascpects of different transport technologies. Road transport related air pollution, Sources of air pollution, effects of weather conditions; Vehicular emission parameters, pollution standards, measurement and analysis of vehicular emission; Mitigative measures; EIA requirements of Highway projects, procedure; MOEF/World Bank/ RC/UK guidelines; EIA practices in India. CEL450 Introduction to Remote Sensing 3 credits (2-0-2) What is Remote Sensing? Historical development of remote sensing, Remote sensing components, Data collection and transmission, Sensors and satellite imageries, Electromagnetic energy and spectrum, Wavebands, Interactions of electromagnetic energy with atmosphere and earth s surface, radiometric quantities, Photogrammetry and aerial photography, Vertical and tilted photographs, Photographic materials, Photo-processes, Stereoscopic viewing, Fly view, Aerial mosaics, Various satellite systems and monitoring programs, Data Products, Satellite data, Data formats, Data acquisition for natural resources management and weather forecast, Random errors and least square adjustment, Coordinate transformation, Photographic interpretation, Image processing, Potential applications of remote sensing in diverse areas and decision making, Integrated use of remote sensing and GIS, Case studies. CEL451 Water Power 4 credits (3-0-2) Pre-requisites: CEL251 Basic principle of hydropower generation, Hydropower Project Planning, Site selection, Hydropower development schemes, Reservoir storage, Assessment of power potential, Hydrologic analysis: Flow duration and power duration curves, Dependable flow, Design flood, Reservoir operation; Hydraulic design of various components of hydropower plants: intakes, hydraulic turbines, centrifugal and axial flow pumps, conduits and water conveyance, Penstocks; Performance characteristics of turbines, Specific and unit quantities, Electrical load on hydroturbines, Power house dimension and planning, Water hammer and surge analysis, Surge tanks, Small hydro power development, tidal plants, Current scenarios in hydropower development, Project feasibility, Impact of hydropower development on water resources systems, environment, socioeconomic conditions and national economy. CEP452 Computational Aspects in Water Resources 3 credits (1-0-4) Pre-requisites: CEL251 Numerical Interpolation and Integration and application of water resource problems. Numerical solution of differential 147 P a g e

148 equations in water resources, such as, groundwater flow, pipe flows, open channel flows. CEL453 Water Resources Management 4 credits (3-1-0) Pre-requisites: CEL251 Scope of Water Resources Management, Global Trends in Water Utilization, Crop Water Requirements and Irrigation Planning, Modern Irrigation methods such as Sprinkler and Drip Irrigation, Soil Salinity and Water Logging Hazard Mitigation, Drainage Design, Hydropower Systems Management, Economic Analysis of water Resources Projects, Flood Control studies. CEL455 Introduction to Geographic Information Systems 3 credits (2-0-2) Overlaps with: CEL747 What is GIS. Geographic concepts for GIS. Spatial relationships, topology, spatial patterns, spatial interpolation. Data storage, data structure, non-spatial database models. Populating GIS, digitizing data exchange, data conversion. Spatial data models, Raster and Vector data structures and algorithms. Digital Elevation Models (DEM) and their application. Triangulated Irregular Network (TIN) model. GIS application areas, Spatial analysis, quantifying relationships, spatial statistics, spatial search. Decision making in GIS context. CEL459 River Mechanics 3 credits (2-0-2) Pre-requisites: CEL251 Introduction, river morpohology, drainage patterns, stream order. Properties of mixture of sediment and water, Incipient motion and quantitative approach to incipient motion, channel degradation and armoring. Bed forms and resistance to flow, various approaches for bed load transport, suspended load profile and suspended load equations, total load transport including total load transport equations. Comparison and evaluation of sediment transport equations. Stable channel design with critical tractive force theory. CEL464 Construction Contract and Economics 3 credits (2-1-0) Overview of the to the course, economics of the projects, Time value of money, comparison of alternatives, Depreciation and depletion, Quantity surveying, Direct and indirect costs, Professional agreements; Contracts and specification; Disputes, Arbitration and other methods of dispute resolution. Bidding and bidding models. CEL466 Construction Equipment and Methods 3 credits (2-1-0) 148 P a g e Overview of the course; Basic principles of construction, selection and economy; General construction equipment excavation, earthmoving, drilling, blasting, dewatering, shoring, strutting, disposal and underpinning, well sinking and pile driving, heavy lifting; Operations and maintenance of equipment, Productivity estimates, Cycle time, Planning and scheduling of equipment by networks, Formworks and scaffolding, Concrete construction practices. Prefabrication and modular coordination; Steel construction, special constructions such dams, bridges, high rise buildings, offshore platforms. Civil 152 CEL610 Foundation Note : This course is not meant for students specializing in Geotechnical and Geoenvironmental ; Classification, behaviour of soils effective stress concept, permeability, compressibility, shear strength. Parameters for short and long term stability, Stress distribution, Field explorations scope and depth of investigations, SPT, DCPT, SCPT; Analysis of bearing capacity of shallow foundations, Plate load test; Settlement computations - Immediate and Consolidation; Codal provisions; Types of pile foundations, load carrying capacity of pile foundations including group effects and negative skin friction. Pile load test. CEL612 Construction Methods in Geotechnical (To be offered to specialization in Construction Technology and Management) Ground -Earthwork, earthmoving equipments, soil compaction and stabilization with additives. Ground improvement-deep-in-situ improvement by (a) Vibroloation stone column, (b) compaction piles, (c) impact/dynamic compaction, (d) blasting, (e) pre-loading and drains, (f) in-situ mixing, cement and lime columns; Geotechnical Processes in Soil and Rocks-drilling, blasting, grouting, dewatering; Foundation-piles: (a) precast driven, (b) driven cast in-situ, (c) bored cast in-situ, (d) under-reamed. Caissons; Dams and Embankments-earth dams, earth cum-rock-fill dams, road and rail embankments; Earth Retaining Structures- retaining walls including reinforced earth, braced excavations, sheet piles, diaphragm walls; Underground Structures-tunneling in rock, soil, and in soft ground. Micro-tunneling. CEL614 Geoenvironmental and Geohazards Note: This Course is not meant for Students Spcializing in Geotechnical and Geoenvironmental. Geoenvironmental ; Waste generation; subsurface contamination, waste containment; Types of landfills, design and operation of landfills, subsurface contamination control and remediation; Geotechnical Earthquake : seismology, Strong

149 ground motion, Seismic hazard analysis, Local site effects and design ground motions, liquefaction hazard evaluations and remedial measures; Landslides: Causes and phenomenon associated with landslides, effect of rainfall on slope stability, earthquake triggered landslides, landslide prevention, control and remedial measures; Other Hazards: ground subsidence, ground heave, erosion. CEL651 Rock Note: This course is not meant for students specializing in Rock and Underground Structures. Introduction. Geological considerations. Index properties and rock mass classifications. Strength and failure criteria for rocks and rock masses; Insitu stresses in rocks and their measurement. Strength and deformation behaviour of discontinuities in rocks. Deformation behaviour of rocks and rock masses. Time dependent behaviour of rocks; Application of Rock Mechanics to Underground Structures, Slopes and Foundations. Improving the properties of insitu rock masses. Ground response support methods. Rock excavation. CED701 Minor Project in Geotechnical and Geoenvironmental 3 credits (0-0-6) CEL701 Behaviour of Soils Origin, nature and distribution of soils. Description of individual particle. Clay mineralogy, clay-water-electrolytes. Soil fabric and structure; Effective stress principle. Steady state flow in soils. Effect of flow on effective stress. Determination of coefficient of permeability; Consolidation, one, two and three dimensional and radial consolidation. Variation of effective stress during consolidation. Various consolidation tests and determination of parameters; Stress-path. Triaxial and direct shear tests. Shear behaviour of granular soils. Factors affecting shear beahviour. Determination of parameters; Shear behaviour of fine grained soils. Pore-pressure parameters. UU, CU, CD tests. Total and effective stress-strength parameters. Total and effective stress-paths. Water content contours; Factors affecting strength : Stress history, rate of testing, structure and temperature. Anisotropy of strength, thixotropy, creep. Determination of in-situ undrained strength; Stress-strain characteristics of soils. Determination of modulus values; Critical state model; Behaviour of Soils of India : Black cotton soils, alluvial silts and sands, laterites, collapsible and sensitive soils, aeolin deposits. CEP701 Soil Laboratory 3 credits (0-0-6) Field Investigations and field tests: Drilling of bore hole, standard penetration test. undisturbed and representative sampling. DCP Test, SCP Test, Electrical resistivity. Plate load test. Pile load test; Laboratory Tests: Consolidation test, Direct shear test, Vane shear test. Unconfined 149 P a g e compression test. Unconsolidated undrained triaxial test. Consolidated drained triaxial test. Consolidated undrained triaxial test with pore water pressure measurement. Free swell index test. Swelling pressure test. Flow net solutions by Electrical analogy. CEL702 Slope Stability and Earth Dams Slope Stability: Short term and long term stabilities; Limit equilibrium methods; Infinite slopes; Finite height slopes Swedish method, Bishop s simplified method, other methods; Stability charts; Conditions of analysis steady state, end of construction, sudden draw down conditions; Factor of safety; Codal provisions; Earthquake effects; Seepage Analysis: Types of flow; Laplace equation; Flownet in isotropic, anisotropic and layered media; Entrance-exit conditions; Theoretical solutions; Determination of phreatic line; Earth Dams: Introduction; Factors influencing design; Design of components; Construction; Instrumentation piezometer, settlement gauge, inclinometer; Road and rail embankments. Reinforced Slopes: Steep slopes; Embankments on soft soils; Reinforcement design; Landslides: Remedial measures for unstable slopes soil nailing, gabions, drainage. CEP702 Geoenvironmental and Geotechnical Laboratory 3 credits (0-0-6) properties and compaction characteristics of waste coal ash, mine tailings. Permeability of clays and bentonite amended soils. Tensile strength of geomembranes, geotextiles. Soil geomembrane interfacial shear strength. Project based laboratory for evaluation of engineering properties of soils for design of embankments and foundations. CEL703 Site Investigations and Ground Improvement Site Investigations: Planning of investigation programmes, Information required for planning different stages of investigations. Geophysical methods: electrical resistivity, and seismic refraction methods. Methods of site investigations: Direct methods, semi-direct methods and indirect methods, Drilling methods. Boring in soils and rocks, methods of stabilizing the bore holes, measurement of water table, field record. Field tests: In-situ shear test, in-situ permeability test, SPT, DCPT, SCPT, in-situ vane shear test, pressure meter test, plate load test. Codal provisions; Sampling techniques, Sampling disturbances, storage, labeling and transportation of samples, sampler design, influence on properties; Report writing. Safety measures; Geotechnical Processes: Principles of compaction, Laboratory compaction, behaviour of compacted clays, field compaction techniques- static, vibratory, impact, Earth moving machinery, Compaction control. Shallow Stabilization with Additives: Lime, flyash, cement and other

150 chemicals and bitumen; Deep Stabilization: sand column, stone column, sand drains, prefabricated drains, electroosmosis, lime column. soil-lime column. Grouting : permeation, compaction and jet. Vibro-floatation, dynamic compaction, thermal, freezing. Dewatering systems. Civil 153 CEL704 Shallow and Deep Foundations Types of Foundations Shallow Foundations: Design considerations factors of safety (including limit state), allowable settlements, location and depth of foundations, Codal provisions. Presumptive bearing capacity. Bearing capacity theories. Layered soils. Choice of shear strength parameters. Bearing capacity from N-values, static cone tests, plate load tests; Settlement : Total and differential settlement. Stress distribution. Consoli-dation settlement in clays ( with correction factors). Immediate settle-ment. Settlement in sands from N-values, elastic solutions. Static cone tests, Plate load tests; Deep foundations : Types of piles. Construction methods. Axial capacity of single piles dynamic formulae, soil mechanics approach. Skin friction and end bearing in sands and clays. Deep foundation. Axial capacity of groups. Settlement of single piles and groups. Uplift capacity (including under-reamed piles). Negative skin friction. Pile load tests. Pile integrity tests. Codal provisions; Caissons; Foundations in difficult soils : expansive soils, chemically aggressive environment, soft soils, fills, regions of subsidence. CEL705 Geoenvironmental Sources and effects of subsurface contamination; Physical, chemical and biological characteristics of solid wastes; Soil-waste interaction; Contaminant transport; Laboratory and field evaluation of permeability; Factors affecting permeability; Waste disposal on land; Types of landfills: Siting criteria; Waste containment principles; Types of barrier materials; Planning and design aspects relating to waste disposal in landfills, in ash ponds and tailing ponds, and in rocks; Environmental monitoring around landfills; Detection, control and remediation of subsurface contamination; properties and geotechnical reuse of waste materials such as coal ash, mining waste, demolition waste etc; Reclamation of old waste dumps; Regulations; Case studies. CEL706 Geosynthetics Geosynthetics and Reinforced Soil Structures: Types and functions; Materials and manufacturing processes; Testing and evaluations; Principles of soil reinforcement; Design and construction of geosynthetic reinforced soil retaining structures walls and slopes; Codal provisions; Bearing capacity improvement; embankments on soft soils; Indian experiences; Geosynthetics in Pavements: Geosynthetics in roads and railways; separations, drainage and filtering in road pavements and railway tracks; overlay design and construction; AASHTO and other relevant guidelines; french drains; Geosynthetics in Environmental Control: Liners for ponds and canals; covers and liners for landfills material aspects and stability considerations; Landslides occurrences and methods of mitigation; Erosion causes and techniques for control. CEL707 Soil Dynamics and Geotechnical Earthquake problems involving soil dynamics; Role of inertia; Theory of Vibrations: Single and two-degree freedom systems, vibrationmeasuring instruments, vibration isolation, Wave propagation in elastic media; General nature of soil behaviour under cyclic/dynamic loading; Field and Laboratory tests for measurement of small straind and large strain, dynamic properties of soils; Design criteria for machine foundations, elastic homogeneous half space solutions, lumped parameter solutions. Codal provisions; Strong Ground Motion: Measurement, characterization and estimation; Amplification theory and ground response analysis. Densification and liquefaction of granular soils, Seismic slope stability analysis, Seismic bearing capacity and earth pressures. Codal provisions. CEL708 Earth Pressures and Retaining Structures Earth Pressure: Types at rest, active and passive; Rankine s theory; Backfill features soil type, surface inclination, loads on surface, soil layers, water level; Coulomb s theory; Effects due to wall friction and wall inclination; Graphical methods; Earthquake effects; Rigid Retaining Structures: Types; Empirical methods; Stability analysis; Flexible Retaining Structures: Types; Material; Cantilever sheet piles; Anchored bulkheads free earth method, fixed earth method, moment reduction factors, anchorage; Braced Excavation: Types; Construction methods; Pressure distribution in sands and clays; Stability bottom heave, seepage, ground deformation; Reinforced Soil Walls: Elements; Construction methods; External stability; Internal stability; Laterally Loaded Piles: Short and long piles; Free head and fixed head piles; Lateral load capacity of single piles; Lateral deflection; Elastic analysis; Group effect; Lateral load test; Codal provisions; Underground Structures in Soils: Pipes; Conduits; Trenchless technology; Tunnelling techniques cut-andcover method, shield tunnelling. CEL709 Offshore Geotechnical Submarine soils: Origin, nature and distribution. Terrigenic and pelagic soils. Submarine soils of India. behaviour of submarine soils: under-consolidated soils, calcareous soils, cemented soils, corals; Offshore site investigations: sampling and sampling disturbance, insitu testing, wireline technology. Offshore pile foundations for jacket type structures. Foundations of gravity structures; Foundations for jack-up rigs. Anchors and breakout forces; anchor systems for floating structures. Stability of 150 P a g e

151 submarine slopes. Installation and stability of submarine pipelines. CEL712 Landfills and Ash Ponds Integrated solid waste management of municipal solid waste, hazardous waste, coal ash and other wastes; Landfilling practice for different types of solid wastes; Municipal solid waste landfills: acceptability of waste; planning, design, construction, operation and closure including management of leachate and gas; Hazardous waste landfills: Waste compatibility and acceptability; planning, design, construction, operation, closure and environmental monitoring; Ash ponds: Slurry disposal versus dry disposal; properties of bottom ash, fly ash and pond ash; planning and design; incremental raising of height by upstream and downstream methods; closure and reclamation. CEL714 Special Topics in Geotechnical and Geoenvironmental A course which will vary from year to year to study new and exicting developments in the broad spectrum of Geotechnical and Geoenvironmental. The course will also focus on new offshoots of Geotechnical and Geoenvironmental. CEL715 Soil-Structure Interaction Analysis Introduction: Analysis of foundations and flexible retaining structures by conventional method- isolated and combined footings, mats, pile caps, eccentrically loaded foundations, transmission tower foundations, sheet pile walls; Soilstructure interaction : Subgrade reaction method; Beam and plate theories; Analysis of footings, mats, pile caps, laterally loaded piles, sheet pile walls, water front structures; Elastic half-space method: Closed form solutions, charts and FEM- footings, mats, reinforced foundations and embankments. Evaluation of relevant material parameters. Use of appropriate software packages. CEL717 Advanced Structural Analysis Matrix methods in skeletal structural analysis : force and displacement methods including analysis using substructures. Non-linear and elastoplastic analysis. Analysis of plates, folded plates and singly curved shells: conventional and approximate methods. CEL718 Design of Steel Structures 3 credits (2-1-0) Structural steels. Brittle fracture and fatigue. Stability of beam columns, frames and plates. Plastic design of steel structures. Plate girders. Codal provisions. Prestressed steel construction. CEL719 Structural Dynamics Free and forced vibration of single degree of freedom (SDOF) systems, response to harmonic, periodic, inpulsive and general dynamic loading, Civil 154 response of SDOF to earthquake. Free vibration of lumped multidegree of freedom systems. Approximate methods for obtaining natural frequencies and mode shapes. Frequency domain analysis of lumped multi-degree of freedom system using normal mode theory. Time domain analysis using numerical integration scheme. Free and forced vibration of continuous systems. Dynamic soil-structure interaction. CEL721 Design of Concrete Structures 3 credits (2-1-0) Limit state design concepts in flexure, shear, torsion and combined stresses; Slender columns. Safety and serviceability : control of cracks and deflections. Yield line analysis of slabs : Work and equilibrium methods. Introduction to limit design of beams and frames. Design of statically determinate prestressed concrete structures for flexure and shear. CEL722 Solid Mechanics in Structural Theories of Stress and strain; Finite deformations and linearization; Compatibility relations; Equations of motion; General theory of constitutive equations; Stress-strain relations for linear elastic solids. Types of elasticity problems and methods of their solution with illustrative examples for isotropic solids. Displacement potentials and stress functions; Torsion; Mechanical principles; Energy theorems; Hypoelastic and hyperelastic solids; Conservative structures. St.Venant s principle; Limitations of the structural theory; Elastic Waves; Thermoelasticity ; Theory of perfect plasticity; Yield criteria, and Flow rules; Viscoelasticity; Rheological odels;superposition and correspondance principles. Viscoplasticity. CEL724 Earthquake Analysis and Design Seismology, seismic risk and hazard, Soil dynamics and seismic inputs to structures, Response spectrum analysis, Spectral analysis, Nonlinear and push over analysis, Dynamic soil-structure interaction. Earthquake design philosophy, codal provisions for seismic design, retrofitting and strengthening of structures, concept of base isolation design and structural control. CEP724 Water Resources Management Laboratory 3 credits (1-0-4) Field based experiments: Soil moisture tension measurement, Capillary pressure, Soil moisture, Infiltration capacity, Soil salinity, Soil nutrients, Water quality; Map reading, impact of changes in land use through map preparation, Use of GIS and remote sensing, Computer based simulation/design, Database design, Water hammer 151 P a g e

152 analysis, Design of water distribution network, Applications of Kriging and Neural networks in water resources. CEP726 Structural Laboratory 3 credits (0-0-6) Concrete: Concrete mix design and testing, non-destructive testing of concrete. Reinforced concrete : under-reinforced and over reinforced beams, columns under eccentric loading, two-way reinforced slabs. Model testing : Models of plates and shells and frames under static and dynamic loading, free and forced vibrations using MTS, dynamic modulus. Stress analysis : Two and three- dimensional photoelasticity. CEL727 Design of Industrial Structures 3 credits (2-1-0) Planning of industrial structures. Design of single and multibay industrial structures in steel and concrete. Bunkers and silos. Pressure vessels and chimneys. Cooling towers. Large span roof structures. Suspended roof structures. Structural aspects of machine foundations. CEL729 Advanced Design of Bridges 3 credits (2-1-0) Introduction and selection of type of bridges; Loads and forces. Grillage analogy. Theories of lateral load distribution and design of superstructure. Abutments, piers and their foundations. Bearings. Expansion joints. Construction methods. Maintenance of bridges. Evaluation of existing bridges. CEL731 Prestressed/ Composite Structures Need for prestressing; Pretensioning and Post-tensioning methods; Behaviour of prestressed concrete beams; Loss of prestress; Deflections; Bursting forces in anchorage zone; Design methods; Partial prestressing; Analysis of indeterminate structures. Need of composite construction; Design methods for composite beams, slabs, columns and box girders; Behaviour of masonry elements and walls; Design methodology; Stability of columns and walls; Seismic design of reinforced and prestressed masonry. CEL733 Finite Element Method in Structural 3 credits (2-1-0) Review of principles of virtual work and minimum potential energy. Elements of theory of elasticity. Various types of finite elements. Solution procedures. Detailed study of application to structures such as dams, frame-shear walls, grid floors and rafts. Application to vibration and buckling problems. CEL734 Mathematical and Numerical Methods 3 credits (2-1-0) Linear equations and eigenvalue problems. Accuracy of approximate calculations. Non-linear equations, Interpolation. Differentiation and evaluation of single and multiple integrals. Initial and boundary value problems of finite difference method. Newton s method, variational and weightened residual methods. Introduction to finite element method. CEL735 Hydrologic Processes and Modeling Land surface processes. Subsurface and channel processes. Unit Hydrograph and GIUH, Flood Propagation and Routing, Watershed Models, Conceptual Models. Hydrologic Forecasting. CEL736 Environmental Dynamics and Management Environmental property and processes, Environmental simulation models, Elements of environmental impact analysis, Impact assessment methodologies, Framework of environmental assessment, Environ-mental impact of water resources projects, Assessment of hydrological hazards, Environmental management, Case studies. CEL737 Optimisation Techniques in Water Resources Optimization techniques; linear programming, non-linear programming, geometric programming, dynamic programming, Network flow algorithm and Goal programming; Introduction to modern heuristic methods like generic algorithm and simulated annealing. CEL738 Advanced Hydraulics Energy and momentum principles in open channel, Curvilinear Flows, Backwater computations, Controls, Rapidly varied flows, Spatially varied flows, Unsteady flow, Surges, Flood wave passage, Roll waves, Sediment transport, Incipient motion criteria, Resistance to flow and bed forms, Bed load theory, Stratified flows, Fluvial Systems, Industrial Hydraulics. CEL739 Groundwater Hydrology Occurrence and movement of groundwater. Surface and subsurface investigation of groundwater, Flowthrough saturated porous medium. Mechanics of well flow, Aquifer parameters, Pumping tests, Design of water wells, Monitoring well design and consutruction, Well development, well maintenance and rehabilitation, Natural and Artificial recharge of ground water, Salt water intrusion, Introduction to analog and numerical models to solve ground water problems, Application of finite difference method in ground water. CEP740 Simulation Laboratory 4 credits (1-0-6) Hydrological database design and its management, Basics of computing, Discrete event simulation, Random number 152 P a g e

153 generation, Monte Carlo simulation, Simulation of queuing systems, Computer based hydraulic and hydrologic simulation exercises, Application of specific hydrologic and hydraulic software packages, Real time operation and online forecasting. CEL741 Surface Water Quality Modeling and Control River hydrology and derivation of the stream equation, Derivation of the estuary equation, Distribution of water quality in rivers and estuaries, Physical and hydrological characteristics of lakes, Finite difference steady state river, estuary and lake models, Dissolved oxygen models in rivers, estuaries and lakes, Fate of indicator bacteria, pathogens and viruses in water, Basic mechanisms of eutrophication, Lake phytoplanckton models, River eutrophication analysis, finite segment models, Elements of toxic substance analysis. CEL742 Finite Element in Water Resources Introduction to finite element method, Mathematical concepts and weighted residual techniques, Spatial discretization, Shape Functions, Isoparametric elements, Explicit and implicit time marching schemes, Equation assembly and solution techniques, Application: Navier- Stokes equations, dispersion of pollutants into ground and surface water, Flow through earthen dams, seepage beneath a hydraulic structure, Groundwater flow in confined and unconfined aquifers, Incompressible turbulent flow in pipes. CEL743 Economic Aspects of Water Resources Devlopment Data requirements and survey: topographical, geological, hydrological, socioeconomic, technological; market survey; identification of alternate options and associated data requirements and survey, Project feasibility, Demand assessment: planning period and time horizon, economicdemographic projections, integrated and disaggregated analysis and model building; demand resilience and consumer behaviour, Basic economic concepts: present worth, future worth, annuities, discounting techniques, depreciation, Production function and cost curves: components of cost curves, learning curve, expansion path, long term and short term, Estimation of project benefits and costs, Tangible and intangible values, Indifference curves, Pricing concepts: oligopolies, kinked demand curve model, skimming price and penetration price, Economics of natural resources management, Fields of finance, Financial analysis, Economic and financial models, Analysis of water resources projects in real-world settings, Benefit-cost analysis, Risk considerations, Project optimality, Mathematical models for multipurpose and multiobjective projects, Technological forecasting, Welfare and 153 P a g e environmental economics, Capital budgeting and cost allocation. CEL744 Groundwater Flow and Pollution Modeling Subsurface processes and concepts for groundwater resources evaluation, Unsaturated zone properties: Soil moisture levels, Retention curves, Flow through unsaturated porous media, infiltration and Wetting front, Groundwater contamination, Sources and causes of groundwater pollution, Pollution dynamics, Hydrodynamics dispersion, Biodegradation, Radioactive decay, Reactive processes, Multiphase contamination, NAPLs, VOCs, Site specific groundwater quality problems in Indian context, Numerical models, Finite difference methods, Numerical modeling of steady and transient flows in saturated and unsaturated domain, Contaminant transport modeling, Application of FEM and BIEM in groundwater modeling, Regional aquifer simulation, Contaminated groundwater systems and their rehabilitation, Development and optimization based management of aquifer systems, Stochastic models, Random field concepts in groundwater models; Application emerging techniques to groundwater management. CEL745 Water Management Moisture-crop relationship, Irrigation requirements, Irrigation efficiencies, Design of conventional and modern methods of irrigation, Irrigation of arid lands, Drainage of irrigated land, Salinity of soil, Salinity control, Quality of irrigation water, Contaminants and their effects on various crop types, Rain water management, Planning and operation of irrigation systems, Conjunctive use of water, Participatory irrigation management, Water management policy during droughts, Predicting effect of water shortage on crops. CEL746 Hydroelectric Planning of hydropower development, Hydropower potential, Operation of power plants for peaking and base load, Characteristics of power market, Integration of various types of plants, Augmentation of power plants, Pump storage plants, Small hydro power, Surge tanks and hydraulic transients, Penstocks and pressure shafts, Intakes, Reservoir operation for hydropower generation in a multipurpose projects, Basin scale hydropower generation in a multipurpose projects, Basin scale hydropower development, Mathematical models for reservoir sizing and operation. CEL747 Geographical Information Systems (GIS) 3 credits (2-0-2) Introduction to Geographical Information Systems (GIS), Databases and database management systems, Spatial databases, Coordinate systems and georeferencing, Interpolation methods: Deterministic and Statistical; Digital elevation models and their applications, Strategies for

154 development, implementation and management of GIS, Case studies on use of GIS selected from various areas such as water and land resources, environment, transportation, etc., Projects involving creation of small GIS modules related to water resources problems and other generic areas. CEL748 Hydrologic Applications of Remote Sensing Technology 3 credits (2-0-2) Data capture for simulation of land surface processes, inventory, Geomorphology, Landuse classification, Landuse planning and landcover mapping, Flood plain mapping, Flood plain zoning, Principles of remote sensing and its applications in water resources, agriculture and environmental monitoring, Applications in snow and glacier studies, Snow line, Ice cover, Snow-pack properties, Integrated use of remote sensing and GIS, Database preparation and Decision support analysis, Estimation of damages due to hydrologic extremes and preparation of contingency plans, Case studies. CEL749 Water Resources Systems Systems concepts and its application in irrigation, flood control, hydropower generation, water supply and drainage, Storage-yield analysis, Rule curves, Reservoir sizing, Multireservoir systems, Real time operation, Water conflicts, River basin planning, heuristics, Systems reliability, Case studies. CEL751 Properties of Rocks and Rock Masses Introduction. Rock materials, Physical properties, Strength behaviour in uniaxial compression, tension and triaxial state. Laboratory testing methods. Stress-strain relationships. Factors influencing strength. Failure mechanism. Anisotropy. Failure criteria, Coulomb, Mohr s, Griffiths and Modified Griffiths criteria and Empirical criteria. Brittle ductile transition, Post failure behaviour. Strength and deformation behaviour of discontinuities. Rockmass behaviour, Shear strength of jointed rocks, roughness, peak and residual strengths. Strength criteria for rockmass. Intact and rockmass classifications, Terzaghi, RQD, RSR, RMR and Q classifications, Rating, Applications. Creep and cyclic loading. Weathered rocks. Flow through intact and fissured rocks. Dynamic properties CEP751 Rock Mechanics Laboratory 3 credits (0-0-6) Tests and test procedures, Specimen preparation, coring, cutting and lapping. Tolerance limits. Physical Properties: Water absorption, density, specific gravity, porosity, void index, electrical resistivity and sonic wave velocity tests. Mechanical Properties: Uniaxial compression, Point load index and Brazilian strength tests, Elastic properties. Effect of L/D ratio and saturation. Strength anisotropy. Shear tests: Single, double, oblique tests, Triaxial compression tests, Direct shear test. Slake durability and 154 P a g e Permeability tests. Compilation of test data. Classification. Codal provisions. CEL752 Slopes and Foundations Introduction, Short-term and long-term stability. Influence of ground water, Seismic effects. Types of rock slope failures. Infinite slopes, Circular and non-circular slip surface analysis, Stability charts. Plane failure analysis. Wedge failure analysis analytical, Stereographic methods. Buckling and toppling failures, Rock falls, Landslides. Foundations: Bearing capacity, settlement and stress distribution in intact and layered rocks. Foundations of dams. Deep foundations. Tension foundations, Codal provisions. Foundation improvement. Use of appropriate software packages. CEP752 Rock Mechanics Laboratory II 3 credits (0-0-6) CEL753 Structural Geology 3 credits (2-0-2) Origin, interior and composition of the earth. Rock cycle, Igneous, Metamorphic and Sedimentary rocks. Rock structures. Plate tectonics, Continental drift and sea floor spreading. Geological time scale. Layered formations, Attitude, true and apparent dips, topographic maps, outcrops. Measurement of attitude of formations. Folds, types of folds, classification, field study of folds, mechanics of folds, causes of folding. Joints, rock mass concept, Joint description and classification. Three point problems, Depth and thickness problems. Faults, mechanics of faulting, normal, reverse and thrusts, faults. Lineations. Foliations, Schistocity. Fault problems. Stereographic projection methods, Use of DIPS software, presentation of geological data and analysis, Applications, Field visit. CEL754 Geotechnical Processes in Rock Ground improvement techniques, assessment. Compaction of disintegrated and weathered rocks. Grouting, type of grouts, suspensions, solutions and resins, Rheological models. Viscous and viscoplastic flows. Spherical and radial flows. Groutability. Grouting techniques, materials, equipment, specifications, evaluation and quality control. Case histories, Shotcrete, method and materials, factors. Fibre reinforced shotcrete. Ground anchors, principles of reinforcement, rock bolts, mechanism, mechanical, friction, grouted tensioned and untensioned bolts. Design of bolts. Installation. Equipment. Testing. Cable anchors. Dewatering techniques, classification, assessment of insitu permeability, filter criteria and design of wells, Codal provisions. CEL756 Excavation Methods and Machinery Principles of rock breakage, explosive energy, energy balance, blasting mechanism. Types of explosives, initiators, delay devices, primer and booster selection. Blast

155 hole design. Drilling methods and machines Blast hole timing. Pattern design, open pit and underground blasting, production, estimation and damage criteria of ground vibrations. Controlled blasting. Directional blasting. Safety aspects. Case histories. TBM tunnelling, cutter head, propulsion, shield, erector, spoil remover and backup systems. Factors influencing and evaluation, Excavation mechanics, trapanner, ranging drum shearer, continuous miner twin rotor Marnetta borer, boom machines, transverse boom tunnelling machines and Robins mobile miner. Drag pick cutting, cutting tool materials and wear, disc cutters. Cuttability. Case studies. CEL757 Field Exploration and Insitu Measurements Surface and sub surface exploration methods. Aerial and remote sensing techniques, Geophysical methods, electrical resistivity, seismic refraction, applications. Rock drilling: percussion, rotary drilling, drill bits. Core samplers, Core boxes, Core orientations. Logging, stratigraphic profile, scan line survey, classification. Planning of laboratory tests, report. Stresses in rocks, gravity, tectonics, residual, thermal and induced stresses. Stress anisotropy and stress ratio. Stress relief and compensation techniques, USBM, door stopper cells, flat jack, hydrofrac, strain rossette and dilatometers. Soft and rigid inclusions. Deformability, plate load, pressure tunnel and bore hole tests. Strength tests, insitu compression, tension and direct shear tests. Pull out tests. Borehole extensometers, piezometers, embedment gauges, inclinometers, Slope indicators, packer tests for insitu permeability, Codal provisions. CEL758 Analysis and Design of Underground Structures Introduction. Types and classification of underground openings. Factors affecting design. Design methodology. Functional aspects. Size and shapes. Support systems. Codal provisions. Analysis: Stresses and deformations around openings, Stresses and deformations around tunnels and galleries with composite lining due to internal pressure, Closed form solutions, BEM, FEM. Design : Design based on analytical methods; Empirical methods based on RSR, RMR, Q systems; Design based on Rock support interaction analysis; Observational method- NATM, Convergence-confinement method. Design based on Wedge failure and key block analysis. Design of Shafts and hydraulic tunnels. Stability of excavation face and Tunnel portals. Use of appropriate software packages. CED760 Minor Project in Rock Under Ground Structures 3 credits (0-0-6) CEL760 Finite Element Method in Geotechnical 155 P a g e Introduction. Steps in FEM. Stress-deformation analysis:one-,twodimensional formulations; Threedimensional formulations; Boundary conditions; Solution algorithms; Descretization; use of FEM2D Program and Commercial packages. Analysis of foundations, dams, underground structures and earth retaining structures. Analysis of flow (seepage) through dams and foundations. Linear and non-linear analysis. Insitu stresses. Sequence construction and excavation. Joint/interface elements. Infinite elements. Dynamic analysis. Evaluation of material parameters for linear and non-linear analysis, Recent developments. CEL761 Underground Space Technology Tunnels, energy storage caverns, nuclear waste disposal repositories, metros, underground chambers and defence installations. Geological considerations, layout, survey and alignment. Analysis and design methods. Construction methods. Ventilation, provisions, equipment. Control and monitoring system, services, operations and maintenance. Lighting, specifications, maintenance, emergency lighting. Power supply and distribution, Water supply and distribution. Safety provisions, localized hazards, fire hazards in highway tunnels, rapid transit tunnels. Surveillance and control system for highway tunnels. Tunnel finish, Rehabilitation. Inspection methods, Repairs, Tunnel construction contracting. CEL762 Special Topics in Rock A course which will vary from year to year to study new and emerging developments in the broad spectrum of Rock. The course will also focus on new offshoots of Rock. CEL763 Environmental Rock Hazardous Earth processes. Temperature, pressure and water related problems, stress relaxation, high ground stresses, rock bursts, subsidence. Karst formations. Landslides and rock falls, slopes stabilization, mitigation, Case studies. Earthquakes, tectonic stresses, creep, ground motions, damage, prediction. Volcanic activity and hazard. Tsunamis. Case studies. Waste disposal, Radioactive and hazardous wastes, repositories, location and design, VLH, VDH and KBS3 concepts. Waste container, barriers, rock structure, embedment, buffers and seals. Performance assessment, quality control and monitoring. Case histories. CEL766 Systems Design and Value Analysis Analysis synthesis, Appraisal, System design procedure, objectives and constraints, application to buildings, value analysis. Indtroduction, function analysis. Job plan. Value savings during construction. Value management. Case studies in Value engineering. CEL767 Construction and Contract Management

156 Project cost estimation, rate analysis, overhead charges, bidding models and bidding strategies. Qualification of bidders, Owner's and contractor's estimate. Tendering and contractual procedures, Indian Contract Act1872, Definition of Contract and its applicability, Types of contracts, International contracts, FIDIC, Conditions and specifications of contract. Contract administration, Claims, compensation and disputes, Dispute resolution techniques, Arbitration and Conciliation Act 1996, Arbitration case studies, Professional ethics, Duties and responsibilities of parties. Management Information systems. CEL768 Recent Advances in Construction Materials Foams and light weight materials, fibre-reinforced concrete. Types of fibres, workability, mechanical and physical properties of fibre reinforced concrete. Industrial waste materials in concrete, their influence on physical and mechanical properties and durability of concrete, Concrete at high temperature. High strength concrete. Changes in concrete with time, Corrosion of concrete in various environments. Corrosion of reinforcing steel. Electrochemical process, measures of protection. Ferro-cement, material and properties. Polymers in Civil Polymers, fibres and composites,fibre reinforced plastic in sandwich pancels, modeling. Architectural use and aesthetics of composties. Adhesives and sealants. Structural elastomeric bearings and resilient seating. Moisture barriers, Polymer foams and polymers in Building Physics. Polymer concrete composites. CEL769 Project Planning and control 3 credits (2-1-0) Work-study, work breakdwon structure, Time estimates, Applications of CPM/PERT, statistical concepts, Man- Material-Machinery-money optimization, scheduling, monitoring, updating. Cost functions, timecost trade off, resource planning-levelling and allocation. Resources - based networks, crashing, master networks, interface activities and dependencies, line of balancing techniques, application of digital computers. Material managementpurchases management and inventory control, ABC analysis. Human Resource management. CEP770 Computation Lab for Construction Management 3 credits (0-0-6) Programming and use of spreadsheet and software in estimation, quantity survey, Network preparation and computations, scheduling and allocation etc., application of L.P. in construction problem, statistical quality control at site. CEL771 Civil Materials Cement selection for civil works. Concrete making materials. Fresh concrete and its rheology. Mechanical, deformational behavior and microstructure of hardened concrete. Creep and shrinkage. Testing of concrete. 156 P a g e Durability of plain and reinforced concrete, Structural steels including alloyed and cold - worked steels. CEL772 Quantitative Methods in Construction Management 3 credits (2-1-0) Introduction and concepts of probability and statistics, Linear programming, Transportation and assignment problems. Dynamic programming, Queuing theory, Decision theory, Games theory. Simulations applied to construction, Modifications and improvement on CPM/PERT techniques. CEL773 Management of Quality and Safety in Construction 3 credits (2-1-0) Introduction to quality. Planning and control of quality during design of structures. Quantitative techniques in quality control. Quality assurance during construction. Inspection of materials and machinery. In process inspection and test. Preparation of quality manuals, checklist and inspection report. Establishing quality assurance system. Quality standards/codes in design and construction. Concept and philosophy of total quality management (TQM). Training in quality and quality management systems (ISO-9000). Concept of safety. Factors affecting safety: Physiological, Psychological and Technological. Planning for safety provisions. Structural safety. Safety consideration during construction, demolition and during use of equipment. Management of accidents/injuries and provision of first aid. Provisional aspect of safety. Site management with regard to safety recommendations. Training for safety awareness and implementation. Formulation of safety manuals. Safety legislation, standards/codes with regard to construction. Quality vs Safety. Case Studies. CEL774 Construction Practices Concrete Construction methods: form work design and scaffolding, slip form and other moving forms, pumping of concrete and grouting, mass concreting (roller compacted concrete), ready mixed concrete, various methods of placing and handling concrete, Accelerated curing, Hot and cold weather concreting, Under water concreting, Prestressing. Steel and composites construction methods: Fabrication and erection of structures including heavy structures, Prefab construction, Industrialized construction, Modular coordination. Special construction methods: Construction in Marine environments, High rise construction, Bridge construction including segmental construction, incremental construction and push launching techniques, River valley projects. CEP775 Construction and Information Technology Laboratory 3 credits (0-0-6) Test related to quality control at site, In-situ test methods, Tests related to damage assessment and performance

157 monitoring of structures. Spreadsheet software application in construction management, AUTOCAD, Estimation of project costs, Application of project planning software. CEL776 Functional Planning, Building Services and Maintenance Management Components of urban forms and their planning. Concepts of neighourhood unit. Street system and layout in a neightourhood. Civil 158 Functional planning of buildings, optimization of space: Spatial Synthesis graphical techniques, heuristic procedures, formulation of linear and nonlinear optimization problem. Space requirements and relationships for typical buildings, like residential offices, hospitals, etc. Standard fire, fire resistance, classification of buildings, means of escape, alarms, etc. services in a building as a systems. Lifts, escalators, cold and hot water systems, waster water systems, and electrical systems. Building Maintenance: Scheduled and contingey maintenance planning. M.I.S. for building maintenance. Maintenance standards. Economic maintenance decisions. CEL777 Building Science Climatic factors, classfication of tropical climates, site climate, microclimate of human settlements, ventilation requirements for health, mechanisms and estimation of natural ventilation, airflow patterns in building. Thermal comfort factors, comfort indices, thermal quantities, heat exchange in buildings, periodic heat flow. Mechanical and structural means of thermal control. Moisture control in buildings. Propagation of sound, sound insulation absorption and transmission, reverberation, Design of floor, roofing and walling system for sound absorption and insulation. Design of auditaria Noise control in buildings, Day lighting, Design of fenestration in buildings for day light of various types, illumination design, luminaries and their characteristics, codal requirements. CEL778 Construction Methods and Equipment Factors affecting selection of equipment - technical and economic, construction engineering fundamentals, Analysis of production outputs and costs, Characteristics and performances of equipment for Earth moving, Erection, Material transport, Pile driving, Dewatring, Concrete construction (including batching, mixing, transport, and placement) and Tunneling. CEL779 Construction Economics and Finance Construction accounting, Profit & Loss, Balance Sheet, Income statement, Ratio analysis. Depreciation and amortization. economics, Time value of money, discounted cash flow, NPV, ROR, PI, Basis of comparison, Incremental rate of return, Benefit-cost analysis, Replacement analysis, Break even analysis. Risks and uncertainties and management decision in capital budgeting. Taxation and inflation. Work pricing, cost elements of contract, bidding and award, revision due to unforeseen causes, escalation. Turnkey activities, Project appraisal and project yield. Working capital management, financial plan and multiple source of finance. International finance, Budgeting and budgetary control, Performance budgeting. appraisal through financial statements, Practical problems and case studies, Project cash flow. CEL781 Urban and Regional Transportation Planning 3 credits (2-0-2) Fundamentals of transportation planning. Components of transportation system and their interaction.historical development and current status of techniques used in travel demand forecasting; Economic and Social Theory of travel demand forecasting; Trip generation, trip distribution, mode choice, traffic assignment. Dimension of the widening role of urban transportation systems planning, the planning process and use, and transport system models. Role of Environment, City structure and fabric. Comparison and evaluation of various models. Simultaneous travel demand models: Parameter Estimation and Validation. Transportation impact study methodologies. Regional analysis and development concepts. Data collection and use of surveys. The role of transportation planning in the overall regional system. Methodology and models for regional transportation system, planning, implementation framework and case studies. Applications to passenger and freight movement in urban and regional contexts. Implications for policy formulations and analysis. CEL782 Pavement Materials and Construction Techniques 3 credits (2-0-2) Subgrade: Various Tests and interpretation in pavement design. Aggregates: Types of aggregates and their properties and tests, batching processes. Binder: types of binders, Physical and chemical properties; Polymer and Rubber Modified binders. Relevant IS and IRC codes, Concrete as Pavement Material: Properties and testing, Concrete Technology in Pavements. Fly ash and its characterisation. Performance based mix Design approaches. Viscoelastic properties of bitumen and bituminous mixtures. Construction Methods: Bituminous and Concrete Pavements. Synthetic, Slog, Waste material. Resolunt Modulus. Finite Element. CEL783 Traffic 4 credits (3-0-2) Traffic studies: Survey and analysis. types of Distributions: Speed, Flow and Headways. Composite Distributions. Traffic Forecasting.Concept of level of service and capacity.intersection studies. Parking Studies, O-D Study and other traffic data collection methods, Gap Acceptance methods. Traffic Signs and Markings. Miscellaneous Traffic Control Devices. Road Lighting. Signalised traffic intersection design round about, signal co-ordination. Traffic flow, delay models. Highway Capacity. 157 P a g e

158 CEL784 Design and Maintenance of Pavements 4 credits (3-0-2) Design pavement structure. Stresses in rigid and flexible pavements, sub-grade evaluation. Design of flexible, semiflexible and rigid pavements. Temperature stresses and joints. Pavement management System; Rehabilitation of Pavements; Pavement Inventories and Evaluation; Quality Control; Pavement Lifecycle and cost analysis. Finite Element Approach. CEL785 Advaced Transportation Modelling 3 credits (2-0-2) Introduction to transportation systems. Transportation innovations, social and economic impacts of transportation. Decision makers and their options, demand modeling and prediction. Stated and Revealed Preference approaches; Modeling transportation technologies. Analysis of network flows. Transportation networks. Network Theory. Shortest Path Methods: Simple, Multiple, K-Shortest Paths. Path Finding Algorithms and applications in Real time vehicle routing Wardrop's external principles of traffic assignments, evaluation of impacts. Basic physics of transportation Entropy. Location models. Systems approach and its application to transportation engineering and planning; prediction of flows and level of service; production function and cost optimization; network analysis and equilibrium assignment; decision analysis and multidimensional evaluation of transportation projects. Transportation and economic policy, mathematical programming and other modes for selecting network investments. Traffic Pollution. CEL786 Geometric Design of Streets and Highways 3 credits (2-0-2) Design control and criteria, relationship of traffic to highway design, design speed, design vehicle. Highway classification, sight distances. Superelevation, highway curves: horizontal and vertical, highway alignment and profile. Geometric design of intersections; grade separation and interchanges. Relevant IRC standards for urban and rural roads. CEL787 Transportation Safety and Environment Multidisciplinary approach to planning for traffic safety and injury control; precrash, crash and post crash models; roles of vehicle, roadway traffic, driver, and environment, crash and injury causations; Road Safety Audit; Mixed traffic flow; Transport related pollution; Technology Vision-2020; Urban and non-urban traffic noise sources, Noise level factors, Noise pollution; Energy related aspects of different transport technologies. Traffic Calming Measures. Road transport related air pollution, Sources of air pollution, effects of weather conditions, Vehicular emission parameters, pollution standards, measurement and analysis of vehicular emission; Mitigative measures; EIA requirements of Highway projects, procedure; MOEF World Bank/RC/UK guidelines; EIA practices in India CEL788 Public Transportation Systems Transit System; Estimation of Transit Demand; Route planning techniques; Bus Scheduling; Transit Corridor identification and planning; Mass Transport Management Measures; Integration of Public Transportation Modes. Public transport Infrastructure; Case Studies. Multimodal Transportation Systems. CEL789 Transportation Systems Management Quick response travel evaluation procedure, TSM actions: Traffic management techniques for improving vehicular flow, preferential treatment for high occupancy modes, demand management technique for reduced traffic damand, staggered hours, vehicle restrictions. Small area management: individual sites, residential neighbourhoods, planning for pedestrians, parking planning. Travel demand management and telematics in travel planning. CEP789 Environmental Chemistry and Microbiology 3 credits (1-0-4) Chemical Equilibria and Kinetics Fundamentals. Acids and Bases; Titrations; Acidity; Alkalinity; Buffers and Buffer Intensity; Chemical equilibrium calculations; pc-ph diagram, Langelier index, Solubility diagram; Oxidation and Reduction reactions. Structure of cell; Types of microorganisms found in the environment; Metabolic classification of organisms. Laboratory Procedures for determining the physical, chemical and microbial parameters of water and wastewater. CEP790 Advanced Environmental Laboratory 4 credits (1-0-6) Principles of instrumentation. Use of advance electronic instruments for analyzing quality of water, waste and air. Experimental data interpretation. Operation of batch scale models for various processes : Activated sludge process, Disinfection, Settlers, Coagulation, Filtration, Anaerobic digestion, Adsorption. Design and operation of treatability studies and microbial growth kinetics. Package programmes for water and wastewater conveyance, treatment and disposal. CEL793 Air Pollution and Control 4 credits (3-0-2) Air-pollution definition, sources, classification. Dynamics of pollutant dispersion and disposal. Effects on environment including living and non-living matter. Ambient air quality monitoring techniques. Air pollution indices, standards, norms, rules and regulations. Removal processes. An introduction to air pollution meteorology. Air Laboratory High Volume Sampling, Handy Sampler, Bioaerosols sampler, Indoor Air Sampler, Stack Sampling. CEL794 Solid and Hazardous Waste Management 158 P a g e

159 Municipal Solid Waste : Generation, Rate Variation, Characteristics (Physical, Biological and Chemical); Management Options for Solid Waste, Waste Reduction at the Source, Collection techniques, Materials and Resources Recovery / Recycling. Transport of Municipal Solid Waste, Routing and Scheduling, Treatment, Transformations and Disposal Techniques (Composting, Vermi Composting, Incineration, Refuse Derived fuels, Landfilling). Norms, Rules and Regulations.Biomedical, Hazardous and Nuclear waste Management. Economics of the onsite v/s off site waste management options. Integrated waste management. Stress-strain behaviour of rocks and rock masses : Elastic, elasto-plastic and brittle, Anisotropy. Crack phenomena and mechanisms of rock fracture. Continuum and discontinuum theories : Equivalent material, Block and Distinct element. Fluid flow through intact and fissured rocks Time dependent behaviour of rocks : Creep, Viscoelasticity and Viscoplasticity. Effect of temperature on rock behaviour. Rock dynamics. Physical modelling. CEL795 Water and Wastewater Treatment Processes Water Demands and Sources, Water quality parameters; Epidemiological and toxic aspects. Physical and chemical interactions due to various forces, suspensions and dispersions. Surface and colloidal chemistry. Settling of particles in water, coagulation and flocculation, floatation, filtration-mechanisms and interpretations, ion exchange and adsorption, Chemical oxidation/reduction processes. Disinfection using chlorine, UV, Ozonation. Water stabilization, aeration and gas transfer. Reverse osmosis, Electrodialysis, Desalination. Treatment and sludge management. CEL796 Advanced Wastewater Treatment Microbiological concepts; cells, classification and characteristics of living organisms, charaterisation techniques, reproduction, metabolism, microbial growth kinetics and kinetics of biochemical operations; Modelling of suspended growth systems, techniques for evaluation of kinetic and stoichiometric parameters. Optimal selection of water and waste water treatment chain, Engineered systems, concepts and principles of carbon oxidation, nitrification, denitrification, methanogenasis. Biological nutrient removal; Anaerobic treatment (process options, components of anaerobic reactions that influence process design); Attached growth reactors (process description, design and applications). Decentralised wastewater treatment systems; Low cost options, constructed wetlands. Reliability and cost effectiveness of wastewater systems. CEL797 Environmental Impact Assessment Planning and Management of Environmental Impact Studies. Impact indentation methodologies: base line studies, screening, scooping, checklist, networks, overlays. Prediction and assessment of impacts on the socioeconomic environment. Environmental cost benefit analysis. Decision methods for evaluation of alternatives. Case Studies. Environmental impact assessment at project level, regional level, sectoral level, and policy level. Sustainable development; Environmental policy in planned, mixed and market economies. Preventive environmental management. CES810 Independent Study (Geotechnical and Geoenvironmental ) 3 credits (0-3-0) CED811 Major Project in Geotechnical and Geoenvironmental Part I 6 credits (0-0-12) CED812 Major Project in Geotechnical and Geoenvironmental Part II 12 credits (0-0-24) CEL817 Structural Safety and Reliability Fundamentals of set theory and probability, probability distribution, regression analysis, hypothesis testing. Stochastic process and its moments and distributions, Concepts of safety factors, Safety, reliability and risk analysis, first order and second order reliability methods, simulation based methods, confidence limits and baysean revision of reliability, reliability based design, examples of reliability analysis of structures. CEL818 Design of Plates and Shells 3 credits (2-1-0) Prismatic folded plate systems. Shell equations. Approximate solutions. Analysis and design of cylindrical shells. Approximate design methods for doubly curved shells. CEL819 Concrete Mechanics Introduction; Rheological modelling of fresh concrete; Constitutive equations; Nonlinear elasticity, plasticity, viscoelasticity and fracture mechanics of hardened concrete; Confinement and ductility; Moisture diffusion; Drying shrinkage; Solid and structural mechanics of reinforced concrete, Skew bending, modified compression field and unified theories of R.C. beams under bending, shear and torsion; Bond-slip and phenomenon of cracking in reinforced concrete; Statical and dynamical analysis of R.C. Structures; Trends. CEL801 Advanced Rock Mechanics 159 P a g e

160 CES820 Independent Study (Structural ) 3 credits (0-3-0) CED821 Major Project Part-1 (Structural ) 6 credits (0-0-12) CED822 Major Project Part-2 (Structural ) 12 credits (0-0-24) CEL822 Stability Theory in Structural Finite deformation of Structures Elastic buckling of columns; Statical, dynamical and energy-based approaches. Eccentric loading; Nonlinear viscoelastic and elasto-plastic buckling; Flexural-torsional and lateral bucking of beams ; Imperfection sensitivity; Post-buckling and Catastrophe theories; Stability of nonconservative structures; Nonlinear dynamical systems theory; Chaos theory; Recent trends. CEL824 Design of Offshore Structures 3 credits (2-1-0) Design of offshore platforms : Introduction, fixed and floating platforms. Steel, concrete and hybrid platforms. Design criteria. Environmental loading. Wind, wave and current loads after installation. Stability during towing. Foundations : Site investigations. Piled foundation. Foundations for gravity structures. Behaviour under dynamic loading. Static and dynamic analysis of platforms and components. CEL826 Advanced FEM and Programming 3 credits (2-0-2) Isoparametric formulation for plate and shell elements; various types of elements; Hybrid elements; FEM in dynamic problems, consistent mass matrix; vibration of bars, beams and plate elements; FEM in buckling problems, geometric matrix, buckling of struts and plate elements; Structural modeling by FEM for structures such as shear walls, core walls, bridges and cooling towers; Computational aspects; Interpretation of results; Comparison with other methods. CEL828 Wind Resistant Design of Structures Causes and types of wind; atmospheric boundary layer and turbulence, wind velocity measurements and distribution, Bluffbody aerodynamics, random vibrations and spectral analysis, Alongwind and acrosswind response of tall buildings, towers and slender structures, aeroelastic phenomena, vibration of cable supported bridges and power lines due to wind effects, wind pressure on cooling towers, design of cladding and wind damping devices, Wind tunnel simulations and tornado effects. CEL832 Design of Tall Buildings 3 credits (2-1-0) Structural systems and concepts. Matrix and approximate methods. Interaction of frames, and shear walls. Twist of frames. Analysis of coupled shear walls. Effect of openings. Large panel construction. Foundation-superstructure interaction. Earthquake effects and design for ductility. CEL836 Structural Health Monitoring 3 credits (2-0-2) Concept of structural health monitoring, sensor systems and hardware requirements, global and local techniques, computational aspects of global dynamic techniques, experimental mode shapes, damage localization and quantification, piezo-electric materials and other smart materials, electro-mechanical impedance (EMI) technique, adaptations of EMI technique. Laboratory : Sensor installation and diagnostics, model shape extraction, location and quantification of damage using global dynamic techniques, damage detection using electro mechanical impedance technique, remote monitoring. CEL840 Stochastic Hydrology Probability concepts and advance distribution, Stochastic processes, Regression and correlation, Auto-regressive and moving average processes, FGN, Power Spectra, Sequential generation of data, Generation of stochastic fields, Markovian process, Dis-aggregation, Intervention analysis, Time series analysis and modeling, Stochastic models, Spatial and temporal modeling of hydrological variables, Risk analysis in hydrology. CES840 Independent Study (Water Resources ) 3 credits (0-3-0) CED841 Major Project Part-1 (Water Resources ) 6 credits (0-0-12) CED842 Major Project Part-2 (Water Resources ) 12 credits (0-0-24) CEL843 Traffic Modelling and Simulation 3 credits (2-0-2) Evaluation of various qualitative and quantitative descriptors of traffic flow, car-following analogy, Theories of Traffic Flow: Catastrophe theory, Modelling Process; Taxonomy of model types: Primitive Models; Forecasting pattern Recognition Static Equilibrium; Model's Linear Dynamical Structure; Growth and Decay processes; Pedestrian Flow Modelling and dynamics; Simulation of Discrete and Continuous processes; Application of macro and micro simulation packages. CEL844 Transportation Economics and Finance 160 P a g e

161 Overview of Transportation Economics; Transportation Investments and Economic Development. Basics of economics. Money value of time, discounted cash flow, NPV, ROR, PI, Bases of comparison, incremental rate of return, benefit-cost analysis, replacement analysis, break even analysis, risks and uncertainties and management decision in capital budgeting. Road User Costs; Public Transportation economics; Social Cost of Transportation; project appraisal and project yield. Legal Framework in transport Sector. Financing Transport Infrastructure; Appraisal through financial statements, practical problems and case studies. CEL845 Transportation and Traffic Infrastructure Design Design and drawing of grade intersections, Rotaries, Miniroundabouts, interchanges (cloverleaf, trumpet), multilevel intersections; On-street parking facilities; Off-street parking facilities (parking lots and garages); Layout for buses and trucks; Bridges and Fly-overs; Guard rails; Culverts; Retaining Sides; Mix wells; Pedestrian sideways; Foot bridges; River Spans; Tunnels and Underpasses; Design of Superstructures (T-beam slab, Solid slab right skew and curved spares). Airport Terminal, Sea Port Infrastructure, Railway and Metro Structure. CES850 Independent Study (Rock and Underground Structures) 3 credits (0-3-0) CED851 Major Project Part-1 (Rock and Underground Structures) 6 credits (0-0-12) CED852 Major Project Part-2 (Rock and Underground Structures) 12 credits (0-0-24) CEL866 Infrastructure Development and Management Introduction of Indian infrastructure programme, qualitative and quantitative description of various sectors of infrastructure; life cycle; methodologies for planning - economic evaluation and feasibility study; Issues related to environmental and social impact of infrastructure projects; Regulatory framework for different sectors. Financial modeling - life cycle cost; cash flow; internal rate of return; Benefit cost analysis. Financing schemes; Grant, Government policies and incentives; Fixing of Toll charges/tariff, Option pricing. Infrastructure risks - type and impacts. Assessment of impacts through Earned value analysis, Kalman Filter and time series analysis techniques. Risk Modeling - Monte Carlo simulation; decision tree; fault tree; utility theory, AHP. Policies and guidelines. Private sector participation - public-privatepartnership models, BOT, BOOT, BOO. Forms of 161 P a g e concession agreement, financial closure. Domestic and international experiences; case studies. CED870 Independent Study (Construction & Management ) 3 credits (0-3-0) CED871 Major Project Part-1 (Construction & Management) 6 credits (0-0-12) CED872 Major Project Part-2 (Construction & Management) 12 credits (0-0-24) CES874 Independent Study (Construction Technology & Management) 3 credits (0-3-0) CED875 Major Project Part-1 (Construction Technology & Management) 6 credits (0-0-12) CED876 Major Project Part-2 (Construction Technology & Management) 12 credits (0-0-24) CEL879 Industrial Waste Management and Audit Nature and characteristics of industrial wastes; Prevention versus control of industrial pollution; Linkage between technology and pollution prevention; Tools for clean processes, reuse, recycle, recovery, source reduction, raw material substitution, toxic use reduction and process modifications; Flow sheet analysis; Energy and resource (material and water) audits for efficient usage and conservation; Waste audits, emission inventories and waste management hierarchy for process industries; Environmental performance indicators; Concept of industrial ecology and symbiosis of eco-parks; Case studies of various industries, e.g., dairy, fertilizer, distillery, sugar, pulp and paper, iron and steel, metal plating, refining, thermal power plants. CED881 Major Project Part-1 6 credits (0-0-12) CEL882 Major Project Part-2 12 credits (0-0-24) CEL886 Environmental Systems Analysis 4 credits (3-0-2) Introduction to natural and man-made systems. Systems modeling as applied to environmental systems. Nature of environmental systems, the model building process addressing to specific environmental problems. Introduction to Water pollution and transport and atmospheric

162 processes. Strategies for analyzing and using environmental systems models. Application of optimization methods such as search techniques, linear programming, dynamic programming and integer programming. Integrated management strategies addressing multiobjective planning : Optimization over time. Laboratory Simulation of Environmental Processes, Application of Environmental Databases and Environmental Software Packages, including systems Optimisation. CEL889 Emerging Technologies for Enviromental Management Identification and evaluation of current and emerging technological issues that impact environmental decisionmaking. Linkages between technology, environmental quality, economic gain, and societal goals; Contemporary issues: Environmentally sound technology transfer, emission trading, international resources sharing issues, climate change, international environmental treaties and protocols. CES890 Independent Study (Environmental and Management) 3 credits (0-3-0) Comprehensive review of problems and solutions related to air, water, wastewater, and solid waste management. Identification and evaluation of current and emerging local, regional and global environmental, and socio-economic issues. CED891 Major Project Part-1 (Environmental and Management) 6 credits (0-0-12) CEL891 Thermal Techniques for Waste Treatment Fundamentals of Thermodynamics, combustion, Heat transfer and Mass transfer as applied to waste incineration. Introduction to fuels, reactor design and furnace technology. Combustion of gases, liquids and solids. Products of combustion. Low Temperature Techniques: Autoclaving, Wet Air Oxidation, Microwaving. High Temperature Techniques: Incineration, Gasification, Pyrolysis. Advanced Technologies : Circulating Fluidized Bed Systems, Plasma Arc Pyrolysis, Co-burning, Oxygen Lancing, Starved Air Incineration, Heat recuperation and Energy Recovery, Boilers and Heat Exchangers. Pollution control and management options for thermal techniques. Economics of thermal techniques. CED892 Major Project Part-2 (Environmental and Management) 12 credits (0-0-24) CEL892 Air Quality Modelling Introduction to Air Quality Modelling. Approaches to model formulation. Model classification, criteria for model selection. Air pollution meteorology meteorological parameters, stability classification; plume rise; plume behaviour, dispersion parameters. Wind and Pollution rose diagram Basic diffusion equation, deterministic, numerical and statistical modeling approach. Introduction to boundary layer, turbulence physical modeling approach. Stochastic modeling approach to air pollution dispersion. Theory of Gaussian plume model and its application. Introduction to Air Quality Models. Case studies. CEL894 Management of Water, Waste and Sanitation Utilities Introduction to sustainable management of Water and Sanitation (WATSAN) sector, Development programmes, Feasibility planning. Project Appraisal : Economic, Institutional and Environmental aspect., Institutional & Economical analysis of urban water and sanitation utilities, Contract management, Public-Private Partnerships and related issues. Strategic Management : Change Management, Financial & Marketing Management for water managers, Management, Water quality surveillan programmes. Unaccounted for Water, Customer Service, and Tariff fixation. Case Studies. Globalization and the State s Changing Role in Infrastructure Development, the Financial Institution s role in policy making for water management, Concept of Water Markets and the role of National and Federal Governments. Civil 162 CED895 Major Project (M.S. Research) 40 credits (0-0-80) CEL295 Ecology and Eco-System Dynamics Concepts of diversity. Diversity in eco-systems and habitat classification, important types of eco-systems (e.g. Wetland ecosystem including estuaries, tidal marsh lands, swamps, lakes, etc.), Forest eco-system (including tropical forests, Himalayan and sub-himalayan forest eco-system etc.), Desert eco-system, Coastal shelf eco-system, Temperature and Tundra eco-system, Grasslands etc. Abiotic factors affecting the distribution and productivity of various terrestrial life forms. Leibig s law of minimum. Census techniques, random sampling, various indices of species dominance, richness and abundance, species evenness and diversity. Statistical models, cluster and principal component analysis for similarity studies. Links between diversity and stability. Concept of succession and its use in reclaimation. Facilitation, enablement, Trophic structure, food webs, energy flow diagram, nutrient cycles. Restoration, Reclamation, and Regeneration of Degraded or Destroyed Ecosystems. CEL896 Design of Water and Wastewater Facilities 162 P a g e

163 Design and analysis of water distribution system, Design and analysis of wastewater conveyance system. Water treatment : Source selection process, selection of treatment chain, plant siting, Treatability studies. Design of physicochemical unit operations: screening, flow measurement and pumping, grit removal, equalisation, sedimentation, floatation, coagulation-flocculation, filtration, disinfection. Wastewater Treatment : Design of pretreatment, secondary treatment, and tertiary treatment, disposal systems. Design of processes for nitrogen and phosphorus removal. Sludge stabilization, treatment, sludge thickening, sludge drying, aerobic and anaerobic digestion of sludges. Hydraulics of treatment plants; flow measurement and hydraulic control points, hydraulic profile through the treatment plant. historical date, frequency modeling techniques e.g., Fault Tree Analysis (FTA) and Event Tree analysis (ETA). Case studies. Human factors in risk analysis; Calculation and presentation of risk (individual risk, societal risk); Risk management. Rules, regulations and conventions. CEL897 Membrane Processes for Water and Waste Treatment Introduction to membrane separation processes, Membrane filtration, dead end filtration, Cake filtration. Equation of Ruth, Kozney-Carman law, Cross flow filtration, Reverse osmosis, Nanofiltration, Ultrafiltration, Microfiltration, Membranes and modules, MF/UF experimental set up, Laws of MF/UF, Limiting Phenomena : Concentration polarization and membrane fouling, Mass transport, and Energy balance. Functioning in closed loop, open loop and with re-circulation. Module arrangement: series or parallel and optimisation. Applications: drinking water, municipal wastewater. Case Studies. CEL898 Life Cycle Analysis and Design for Environment products and processes : Environmental health and safety, Product life cycle stages, Material toxicity, pollution, and degradation, Environmentally conscious design and manufacturing approaches, Sustainable development and industrial ecology. System life-cycles from cradle to reincarnation, Product lifeextension, Organizational issues. Pollution prevention practices, Manufacturing process selection and trade-offs. Design for Environment : Motivation, concerns, definitions, examples, guidelines, methods, and tools. Recyclability assessments, Design for recycling practices. Remanufacturability assessments, Design for Remanufacture / Reuse practices. Industrial ecology and Eco-industrial parks. Eco-Labels and Life-Cycle analysis (LCA) : LCA methodology, steps, tools and problems, Life- Cycle Accounting and Costing. ISO Environmental Management Standards. New business paradigms and associated design practices. CEL899 Environmental Risk Assessment Basic concepts of environmental risk and definitions; Hazard identification prodedures; Environmental Risk Zonation; Consequence analysis and modeling (discharge models, dispersion models, fire and explosion models, effect models etc). Estimation of incident frequencies from 163 P a g e

164 44 Department of B.Tech, B.Tech + M.Tech Computer Science CSL105 Discrete Mathematical Structures 4 credits (3-1-0) Overlaps with: MAL180 Decimal Number Systems, Binary Number Systems, Hexadecimal Number Systems, Octal Number Systems and Binary arithmetic Notation, Connections, Normal forms, Truth tables, Equivalence and Implications, Theory of inference for statement calculus, Predicate calculus, Rules of Logic and Mathematical Induction and Quantifiers Review of set concepts, Relations, Properties of relations, Equivalence relations, Partially Ordered Sets (Posets). Concept, Some Special Functions (Polynomial, Exponential & Logarithmic, Abslute Value, Floor & Ceiling, Mod & Div Functions), Properties of Functions,Composition of Functions,Towers of Hanoi, Iterations, Homogeneous linear equations with constant coefficients, particular solution, difference table, finite order differences, Line in a plane in general position,monoids, semi groups,product and quotients of algebraic structures, Isomorphism, homomorphism, automorphism, Normal subgroups, Codes and group codes.graphs Directed, Undirected, Simple,. Adjacency & Incidence, Degre of Vertex, Subgraph, Complete graph, Cycle & Wheel Graph, Bipartite & Complete Bipartite Graph, Weighed Graph, Union of Simple Graphs. Complete Graphs. Isomorphic Graphs, Path, Cycles & Circuits Euclerian & Hamiltonian Graphs. Planar Graph: Kuratowski s Two Graphs, Euler s Formula, Kuratowski s Theorem. CSL201 Data Structures 5 credits (3-0-4) Pre-requisites: CSL101 / CSL102 Introduction to object-oriented programming through stacks, queues and linked lists. Dictionaries: skip-lists, hashing, analysis of collision resolution techniques. Trees, traversals, binary search trees, Balanced BST, Tries. Priority queues and binary heaps. Object oriented implementation and building libraries Applications to discrete event Simulation Sorting: merge, quick, radix, selection and heap sort. Graphs: Breadth first search and connected components. Depth first search in directed and undirected graphs. Union-find data structure and applications. Directed acyclic graphs: topological sort. CSL211 Computer Architecture 5 credits (3-1-2) Pre-requisites: (CSL101/CSL102) Subsystems of a computer; Instructions and their formats; Assembly programming; Performance metrics; Performance comparison; Information representation; Integer and floating point arithmetic; Processor data path design; Control unit design; Microprogramming; Performance improvement with pipelining; Memory organization cache and virtual memory; Input/Output organization; Interrupts and DMA. CSL 312 Programming in C++ 4 Credits (3-0-2) Pre-requisites: CSL101 C++ Overview, C++ Characteristics, Object-Oriented Terminology, Polymorphism, Object-Oriented Paradigm, Abstract Data Types, I/O Services, Standard Template Library, Standards Compliance, Functions and Variables, Functions: Declaration and Definition, Variables: Definition, Declaration, and Scope, Variables: Dynamic Creation and Derived Data, Arrays and Strings in C++, Qualifiers, Classes in C++, Defining Classes in C++, Classes and Encapsulation, Member Functions, Instantiating and Using Classes, Using Constructors, Multiple Constructors and Initialization Lists, Using Destructors to Destroy Instances, Using Destructors to Destroy Instances, Operator Overloading, Operator Overloading, Working with Overloaded Operator Methods, Initialization and Assignment, Initialization vs. Assignment, The Copy Constructor, Assigning Values, Specialized Constructors and Methods, Constant and Static Class Members, Inheritance, Overview of Inheritance, Defining Base and Derived Classes, Constructor and Destructor Calls, Input and Output in C++ Programs, Input and Output in C++ Programs, Standard Streams, Manipulators, Unformatted Input and Output. CSL302 Programming Languages Pre-requisites: CSL201 Notions of syntax and semantics of programming languages; introduction to operational/natural semantics of functional and imperative languages. Data abstractions and control constructs; block-structure and scope, principles of abstraction, qualification and correspondence; parameter passing mechanisms; runtime structure and operating environment; practical and implementation issues in runtime systems and environment; abstract machines; features of functional and imperative languages; the untyped and simply-typed Lambda calculus, type systems for programming languages including simple types and polymorphism; objects, classes and inheritance in objectoriented languages. CSL332 Introduction to Database Systems 4.5 credits (3-0-3) Pre-requisites: CSL201 The world of Database Systems, The E-R Model, The three database models, Representation and Evaluation of Relationship, The Relational Database Model, Functional Dependencies, Multi-valued and join Dependency, Normalization Theory, Concurrency Control in Relational Databases, Object Oriented Data Models. CSL375 Operating Systems 4.5 credits (3-0-3) Pre-requisites: CSL201 & CSL211 & CSL302 Overview: functions of Operating Systems, layered architecture; basic concept; interrupt architecture, system calls and notion of a process and threads; synchronization and protection issues; scheduling; memory management including virtual memory and paging techniques; input output architecture and device management; file systems; distributed file systems; Case studies of Unix, Windows 164 P a g e

165 NT. Design and implementation of small operating systems. CSL 311 Object oriented Programming (OC1) Introduction: Review of structures in C, accessing members of structures using structure variables, pointer to structures, passing structures to functions, structures as user defined data types. Operator overloading: Fundamentals, Restrictions, operator functions as class members v/s as friend functions. Overloading stream function, binary operators and unary operators. Converting between types. Inheritance: Base classes and derived classes, protected members, relationship between base class and derived classes, constructors and destructors in derived classes, public, private and protected inheritance, relationship among objects in an inheritance hierarchy, abstract classes, virtual functions and dynamic binding, virtual destructors. Multiple inheritance, virtual base classes, pointers to classes and class members, multiple class members. Templates, exception handling. CSL313 Database Management Systems (OC2) Pre-requisites: CSL201 The world of Database Systems, The E-R Model, The three database models, Representation and Evaluation of Relationship, The Relational Database Model, Functional Dependencies, Multi-valued and join Dependency, Normalization Theory, Concurrency Control in Relational Databases, Object Oriented Data Models. CSL314 Operating Systems Principles (OC3) 4 credits (3-1-0) Pre-requisites: CSL201 Overview: functions of Operating Systems, layered architecture; basic concept; interrupt architecture, system calls and notion of a process and threads; synchronization and protection issues; scheduling; memory management including virtual memory and paging techniques; input output architecture and device management; file systems; distributed file systems; Case studies of Unix, Windows NT. Design and implementation of small operating systems. CSL356 Analysis and Design of Algorithms 4 credits (3-0-2) Pre-requisites: CSL201 RAM model and complexity: O(log n) bit model, Integer sorting and string sorting, Review of fundamental data structures: Red-black trees, mergeable heaps, interval trees Fundamental design methodologies and their implementations: Search Techniques, Dynamic Programming, Greedy algorithms, Divide and Conquer, Randomized Techniques. Algorithms for set manipulations, their implementations and applications: Union-Find Randomized data structures: Skip Lists, Universal Hash functions, Graph Algorithms with implementation issues; Depth-First Search and its applications, minimum Spanning 165 P a g e Trees and Shortest Paths. Convex hulls, sorting, Selection Matrix multiplication, pattern matching, integer and polynomial arithmetic, FFT. Introduction to the Theory of Lower Bounds, NP-Completeness and Reductions.Approximation algorithms. CSL705 Theory of Computation 4 credits (3-1-0) Pre-requisites: CSL105 Regular Languages, Finite Automata, equivalence, minimization, Myhill-Nerode Theorem, introduction to nondeterminism, Context free grammars, Pushdown automata, equivalence, and applications Turing machines, Recursive and Recursively enumerable sets, non-determinism, RAMs and equivalence, Universal Turing Machines, undecidability, Rice s theorems for RE sets Post machines, Basics of Recursive function theory, quivalence, Church s thesis Computational Complexity, space and time complexity of Turing Machines, Relationships, Savage s theorem, Complexity classes, Complete problems, NP completeness, Cook-Levin theorem. CSL781 Computer Graphics 4.5 credits (3-0-3) Pre-requisites: CSL201 Overlaps with: MAL754, EEL754 Graphics pipeline; Graphics hardware: Display devices, Input devices; Raster Graphics: line and circle drawing algorithms; Windowing and 2D/3D clipping: Cohen and Sutherland line clipping, Cyrus Beck clipping method; 2D and 3D Geometrical Transformations: scaling, translation, rotation, reflection; Viewing Transformations: parallel and perspective projection; Curves and Surfaces: cubic splines, Bezier curves, B-splines, Parametric surfaces, Surface of revolution, Sweep surfaces, Fractal curves and surfaces; Hidden line/surface removal methods; illuminations model; shading: Gouraud, Phong; Introduction to Ray-tracing; Animation; Programming practices with standard graphics libraries like opengl. CSL374 Computer Networks 4.5 credits (3-0-3) Pre-requisites: CSL211 & CSL201 Fundamentals of Digital Communications, including channel capacity, error rates, multiplexing, framing and synchronization. Broadcast network and multi-access protocols, including CSMA/CD. Data link protocols, Network protocols including routing and congestion control, IP protocol. Transport protocol including TCP. Network application services and protocols including , www, DNS. Network security and management. CSL434 Programming in Java 4 Credits (3-0-2) Pre-requisites: CSL201 & CSL302 OBJECTS AND CLASSES: Objects, constructors, returning and passing objects as parameter, Nested and inner classes, Single and Multilevel Inheritance, Extended classes, Access Control, usage of super, Overloading and overriding methods, Abstract classes, Using final with

166 inheritance. PACKAGE AND INTERFACES: Defining package, concept of CLASSPATH, access modifiers, importing package, Defining and implementing interfaces.string HANDLING: String constructors, special string operations, character extraction, searching and comparing strings, string Buffer classexception HANDLING: Exception handling fundamentals, Exception types, uncaught exceptions, try, catch and multiple catch statements. Usage of throw, throws and finally.file HANDLING: I/O streams, File I/O. APPLET: Applet Fundamentals, using paint method and drawing polygons. Planning. Handling uncertainty: Bayesian Networks, Dempster-Shafer theory, certainty factors. Fuzzy logic, Learning through Neural nets- Back propagation, radial basis functions, Neural computational models - Hopfield Nets, Boltzman machines. PROLOG programming. CSD411 Major Project Part 1 (CS) 8 credits (0-0-16) This project spans also the course CSD412. Hence it is expected that the problem specification and the milestones to be achieved in solving the problem are clearly specified. CSL740 Software 4 credits (3-0-2) Pre-requisites: CSL201 & CSL302 Concepts and techniques relevant to production of large software systems: Structured programming. Requirements specification and analysis. Top-down design and development. Information hiding, abstraction, modularity, object-oriented techniques. Separate compilation, configuration management, program libraries. Design patterns; UML. Documentation. Validation. Quality assurance, safety. Testing and test case generation. Software metrics. Cost analysis and estimation, manpower and time management. Organization and management of large software design projects. CSC410 Colloquium (CS) 3 credits (0-3-0) The students will deliver talks on their experience during the 50 working days of practical training, and topics of current interest in the computer science and engineering field. These would include technology, research as well standards issues. CSD412 Major Project Part 2 (CS) 8 credits (0-0-16) Pre-requisites: CSD411 The student(s) who work on a project are expected to work towards the goals and milestones set in CSD411. At the end there would be a demonstration of the solution and possible future work on the same problem. A dissertation outlining the entire problem, including a survey of literature and the various results obtained along with their solutions is expected to be produced. CSL759 Cryptography and Computer Security 4 credits (3-0-0) Pre-requisites: CSL356 or equivalent, MAL250 or equivalent Classical ciphers; private key encryption; hash functions; SHA1, MD5; message authentication; HMAC; pscudorandom permutations: AES, DES; theoretical foundations: one-way functions, pseudorandom generators, number theory; public key encryption: RSA, Rabin, knapsack; digital signatures: RSA, E1 Gamal, Rabin; key distribution: Diffie-Hellman; protocols: oblivious transfer, bit commitment, coin flipping, secret sharing, digital cash, elections; other topics: payments, biometrics, virus & worms, large scale cryptanalysis, identity based encryption etc. CSL728 Compiler Design 4.5 credits (3-0-3) Pre-requisites: CSL302 Compilers and translators; lexical and syntactic analysis, top-down and bottom up parsing techniques, internal form of source programs; semantic analysis, symbol tables, error detection and recovery, code generation and optimization. Type checking and static analysis. Algorithms and implementation techniques for type-checking, code generation and optimization. Students will design and implement translators, static analysis, type checking, and optimization. CSL333 Artificial Intelligence 4 credits (3-1-0) Pre-requisites: CSL201 Problem solving, search techniques, control strategies, game playing (minimax), reasoning, knowledge representation through predicate logic, rule-based systems, semantic nets, frames, conceptual dependency formalism. 166 P a g e

167 45 Department of B.Tech, B.Tech + M.Tech Electrical EEL101 Fundamentals of Electrical 4 credits (3-0-2) DC circuits, KCL, KVL, Network theorems, Mesh and nodal analysis, Step response and transients. RC, RL and RLC circuits, Phasor diagram solution of AC circuits. Power in 1- and 3-phase AC circuits. Two port networks. Operational amplifiers: model and applications. Magnetic circuits. Transformers: modeling and analysis. Energy in magnetic field, production of force and EMF. Electro-mechanical energy conversion. Principles of measurement. Electrical and electronic materials. Laboratory experiments will be based on these topics. EEL201 Digital Electronic Circuits 4 credits (3-1-0) Pre-requisites: EEL101 Review of Boolean Algebra, Karnaugh Map and Logic Gates; Designing combinational Circuits using gates and/or Multiplexers; Introduction to logic families: TTL, ECL, CMOS; PLAs and FPGAs; Sequential Circuits: Flip Flops, Counters and Registers; Design of Sequential Circuits: STD and applications; Pipelining and Timing issues; Memories. EEP201 Electronics Laboratory - I 1.5 credits (0-0-3) Pre-requisites: EEL101 The laboratory is divided into two parts. In the first part, the student is required to perform some set experiments to familiarize himself/ herself with basic digital electronic techniques. In the second half of the semester, the student is required to design and fabricate a digital module. A formal presentation of the design is required at the end of the semester. EEL202 Circuit Theory 4 credits (3-1-0) Pre-requisites: EEL101 Overview of network analysis techniques, Network theorems, Transient and steady state sinusoidal response. Network graphs and their applications in network analysis. Tellengen s theorem, Twoport networks, z, y,h and transmission parameters, combination of two ports, Analysis of common two ports, Resonance, Coupled circuits, Scattering matrix and its application in network analysis. Network functions, parts of network functions, obtaining a network function from a given part. Network transmission criteria; delay and rise time, Elmore s and other definitions of cascading. Elements of network sythesis techniques. Butterworth and Chebyshev Approximation. EEL203 Electromechanics 4 credits (3-1-0) Pre-requisites: EEL101 Review of 1-phase, 3- phase circuits and magnetic circuits, transformers 1-phase and 3-phase, special multiphase transformers and their applications, Electro mechanical Energy conversion principles and rotating machines, DC machines- construction, characteristics, commutation, armature reaction, speed control of DC motors and applications in drives; Synchronous machine-construction, characteristics, regulation, V-curves, parallel operation; Induction machines- 3-phase and 1- phase- construction, characteristics, starting, braking and speed control, Induction generators and applications- Fractional kw motors, special machines- PM machines, SRM, stepper motors and their applications. EEP203 Electromechanics Laboratory 1.5 credits (0-0-3) Pre-requisites: EEL203 Experiments on Transformers, DC and AC machines. EEL204 Analog Electronics Circuits 4 credits (3-1-0) Pre-requisites: EEL101 Review of working of BJT, JFET and MOSFET and their small signal equivalent Circuit; Biasing of BJT, JFET and MOSFET circuits; Analysis and Design of various single stage amplifier configurations; Multi Stage Amplifiers; Differential Amplifier and Operational Amplifier; Feedback Amplifiers; Tuned Amplifiers; Oscillators. EEP204 Electronics Laboratory - II 1.5 credits (0-0-3) Pre-requisites: EEL101 To design and test single stage and multi stage amplifiers, power amplifiers and oscillators on bread board. The students will be given the specification and the design to be verified before wiring up the circuit. The students are encouraged to trouble shoot with hints from the instructor and TAs. EEL205 Signals and Systems 4 credits (3-1-0) Pre-requisites: EEL101 / MAL110 / MAL111 / MAL115 Classification of signals and systems, various system representation techniques, differential, difference and statespace representations, Fourier transforms and series, application to analysis of systems, Laplace transform, its properties, and its application to system analysis, Z transforms, its properties and applications, Random variables and random process, characterization of random variables and random process, linear systems and random signals. 167 P a g e

168 EEL207 Electromagnetics 4 credits (3-1-0) Pre-requisites: PHL110 Review of Maxwell s equations, wave propagations in unbounded medium. Boundary conditions, reflection and refraction of plane waves. Transmission Lines: distributed parameter circuits, traveling and standing waves, impedance matching, Smith chart, analogy with plane waves. Waveguides: parallel-plane guide, TE, TM and TEM waves, rectangular and cylindrical waveguides, resonators. Planar transmission lines: stripline, microstripline, application of numerical techniques. Dielectric guides and optical fibres. Radiation: retarded potentials, Hertzian dipole, short loop, antenna parameters. Radio-wave propagation: ground-wave, sky-wave, space-wave. Introduction to the control problem, Industrial control examples, Transfer function models of suitable mechanical, electrical, thermal and pneumatic systems. Systems with dead time, Control hardware and their models: Potentiometers, synchronous, LVDT, DC and AC servo motors, tacho generators, electro-hydraulic valves, pneumatic actuators. Closed loop control systems, Block diagram and signal flow analysis, Basic Characteristics of feedback control systems : stability, steady-state accuracy, transient accuracy, disturbance rejection, insensitivity and robustness. Basic modes of feedback control :Proportional, Integral, Derivative. Concept of stability and Routh stability criterion. Time response of 2nd order system, steady state error and error constants, Performance specifications in the time domain. Root locus method of design. Lead and lag compensation. Nyquist stability criterion. Frequency response analysis: Nyquist plots, constant M circles, constant N-circles, Bode plots, Nichols Charts Performance specifications in frequency domain, Frequency-domain methods of design. Lead and lag. EEL209 Power Electronics Devices and Circuits 4 credits (3-1-0) Pre-requisites: EEL101 Basic features of semiconductor junctions, the BJT operations at high currents, switching features of the BJT and MOS transistors. The thyristor operation, distributed gates. IGBT operation, principles and ratings. Boost and buck converters using BJT and IGBT circuits-problems, design and operation. Snubber designs and protection. Firing circuits. Thyristor and BJT based converters-design, phase control, effects on power factor and harmonics, firing circuits and their designs. Inverter circuits operation. Designs using BJT s and MOS devices. Base and gate drive circuits, snubbers, operational problems. The basic concept of PWM control and advantages against phase control. AC voltage controllers, choppers and cycloconverters. EEP209 Power Electronics Laboratory 1.5 credits (0-0-3) Pre-requisites: EEL209 Experiments on measurement of turn on and off characteristics of various devices on storage CRO computation of losses. Assembly and testing of converters and inverters on resistive and inductive loads. Fabrication and testing of firing circuits, base and gate drives. Study of turn on and turn off characteristics of junction and MOS devices Performance of low rating boost and buck converters Design and Testing of firing circuits for: (a)thyristorised boost/buck converters.(b) BJT/IGBT based boost/buck converters Phase controlled operation of a six pulse thyristorised converter, and harmonics analysis of performance. Performance study of a commercial, low rating, BJT PWM inverter, and harmonics analysis of performance EEL301 Control - I 4 credits (3-1-0) Pre-requisites: EEL205 Overlaps with: MEL312, CHL P a g e EEP301 Control Laboratory 1.5 credits (0-0-3) Pre-requisites: EEL301 First and Second Order Electrical Systems, A.C and D.C Servo Motors, Synchro Characteristics, D.C Integral Servo Systems, Characteristics of Hydraulic Servo, Amplifier and Servo motor, Pneumatic Process Controller, Process Control Simulator, Microprocessor based speed control of stepper motor. EEL303 Power - I 4 credits (3-1-0) Pre-requisites: EEL203 Energy resources, power generation: Thermal, hydro and nuclear power plants. Transmission lines, line parameters, corona, interference of power lines with communication circuits, line insulators. Cables. EEP303 Power Laboratory 1.5 credits (0-0-3) Pre-requisites: EEL303 Experiments related to EEL303 Power - I EEL305 Electric Drives 4 credits (3-1-0) Pre-requisites: EEL203 Requirements, components and benchmarks of electric drives. Review of induction motor theory, distinction between wound rotor and cage rotor, cases of multiple cages, energy efficient motors, synchronous motor theoryequivalent circuit, extensions as reluctance motors, and permanent magnet motors. Stepper motor features and operation. Speed control of induction motor-basic issues, the ac power controller, and slip energy recovery schemes. VSI and CSI fed induction motors. Speed control of synchronous motors and associated machines.

169 Organization of micro-controllers, key issues like actuation and signal sensing, interrupt handling, timing, and priority of tasks in a microcomputer controlled drives. EEP305 Drives Laboratory 1.5 credits (0-0-3) Pre-requisites: EEL305 Experiments related to course EEL305 Electric Drives. EEL306 Communication 4 credits (3-1-0) Pre-requisites: EEL205 Review of Fourier Series and Transforms. Hilbert Transforms, Bandpass Signal and System Representation. Random Processes, Stationarity, Power Spectral Density, Gaussian Process, Noise. Amplitude Modulation, DSBSC, SSB, VSB: Signal Representation, Generation and Demodulation. Frequency Modulation: Signal Representation, Generation and Demodulation. Mixing, Superheterodyne Receiver, Phase Recovery with PLLs. Noise: in AM Receivers using Coherent Detection, in AM Receivers using Envelope Detection, in FM Receivers. Sampling, Pulse-Amplitude Modulation. Quantization, Pulse-Code Modulation. Noise Considerations in PCM, Time Division Multiplexing, Delta Modulation. EEP307 Electromagnetics Laboratory 1.5 credits (0-0-3) Pre-requisites: EEL207 Laboratory experiments on different transmission lines, antennas, microwave sources and passive devices. EEL325 Control - II Pre-requisites: EEL301 Introduction to digital control systems, Principles of signal conversion, sampling and reconstruction. Principle of discretization. Impulse and step invariance. Finite difference approximation. Bilinear transformation, Mathematical models discrete time signals and systems. Transfer function and system response. Stability on the z domain. Closed loop digital control systems. System with dead time. Commonly used digital devices. Examples of industrial control systems. Transform design of digital controllers. Root locus methods and frequency domain method. State variable representation of continuous and discrete time systems. Conversions state variable models to transfer function models. Conversion of transfer function to canonical models. Eigen values and Eigen vectors. Solution of state equations. Controllability and observability properties. Pole placement design using state feedback. Dead beat control. EEL405 Power Instrumentation Pre-requisites: EEL303 The concepts of accuracy and precision, Log errors and sources of measurement errors. Non idealities involved in Power instrumentation Instrument transformers, structures of PT s and CT s ratio and phase errors. Current probes and their efficiency. DC current measurements by Hall devices, saturable reactor set, UPS. Electromechanical meters for dc and ac measurements-moving coil and moving magnet structures. Analog circuits for power instrumentation, voltage followers, buffers, differential amplifiers, specific analog circuits for peak detection, rms detection, and average computation, common mode operation and noise analysis of OPAMP based circuits. Filter designs and concepts of operating bandwidth. Digital instrumentation in power application, A/D and D/A circuits and their operation, errors Basic concepts of digital filtering storage and related circuit design. Microprocessors in power instrumentation, configuration and software flowcharts for basic power measurement involving filtering, arithmetic operations and storage. EEC420 Colloquium (EP) 3 credits (0-3-0) Pre-requisites: registered for EET420 Students will deliver talks about their experience during practical training, and on topics of current interest. EET420 Practical Training (EP) Non credit Pre-requisites: EC 90 at the end of 5th sem. Fifty (50) working days or 400 hours of practical training in an industry. EED421 Major Project Part 1 (EP) 3 credits (0-0-6) Pre-requisites: EC 120 Formation of project team (up to two students and two faculty guides); formulation of work plan; completion of targeted work for the semester; and presentation of progress for award of grade. Topic should be in the area of electrical power. Completion of about a third of the total work for assessment and grading. EED422 Major Project Part 2 (EP) 7 credits (0-0-14) Pre-requisites: EED421 Continuation of planned tasks started in Project Part 1 to completion, thesis writing and presentation of complete work for award of grade. Completion of the planned work for assessment and grading. EEL451 Power Systems Protection Pre-requisites: EEL303 Basic concepts of power system protection, types of relays, protection of generators, transformers, bus bars and 169 P a g e

170 transmission lines, distance and carrier current protection. Computer relaying. Induction motor protection. Theory of arc interruption, types of circuit breakers (air, air blast, oil, vacuum and SF6), circuit breaker rating and testing of circuit breakers. EEL452 HVDC Transmission Pre-requisites: EEL303 Comparison of HVAC and HVDC transmission, HVDC transmission schemes, Component description, converter: principles, characteristics, control circuits, HVDC system control, Protection, Harmonics and filters, AC-DC system interaction, AC-DC load flow. EEL453 Power System Dynamics and Control Pre-requisites: EEL303 Introduction to power system stability problems, Models of: synchronous machines, excitation systems, prime mover and governor, loads, Transient stability analysis, Dynamic stability analysis, Dynamic Equivalents, Stabilizers, Levels of power system control, AGC, SCADA and Computer control. EEL456 Power - II 4 credits (3-0-2) Pre-requisites: EEL303 per unit system, symmetrical components, fault analysis, switching surges. Integrated operation of power systems, load flow, economic operation, Load management and tariffs, stability analysis, security analysis, optimal power flow, power system control. EEL308 Computer Architecture 4 credits (3-1-0) Pre-requisites: EEL201 Overlaps with: CSL211 Organization of a Computer: von Neumann and Harvard architecture; Instruction Set Architecture: RISC and CISC processors; Computer Arithmetic: fixed point and floating point arithmetic; Design of ALU: hardware algorithms for addition, multiplication and division of fixed point and floating point numbers; Processor design: Data Path and Control Design, Microprogramming, Exception Processing, Pipelining; Memory Organisation: memory hierarchy, cache organization, virtual memory; System Design: bus structure, bus transactions; Input-output Systems: programmed I/O, DMA and interrupt driven I/O. Illustrations with examples of CISC processors from Intel and RISC processors like MIPS and ARM. EEP308 Computer Technology Laboratory 1.5 credits (0-0-3) Pre-requisites: EEL201 & EEP201 Overlaps with: CSL211 Laboratory Experiments will be on: (a) Use of ALU; (b) Design and implementation of special purpose hardware for application specific computation, like HCF; (c) Design and implementation of interfacing hardware, eg. Serial I/O; (d) Assembly Language programming and interfacing experiment with microprocessor/microcontroller kit; (e) Use of Hardware Description Language like VHDL; (f) Controller synthesis on FPGA. EEL339 Power Conditioning Pre-requisites: EEL209 Concepts of nonlinear loads and electric power conditioning unity power factor rectifier STATCON, (Static condenser) SMPS: analysis, design and control. UPS online and off-line, power supplies in telecommunication systems. High frequency induction heating, dielectric heating Power supplies in automobiles. Passive filters, active filters for harmonic and reactive power compensation in two wire, three wire and four wire ac systems. Harmonic standards, power quality, surge suppressors, compensation of arc furnace and traction loads. Microwave ovens, light and temperature controllers. Power supplies for appliances such as camera, X-ray equipment. Case studies on microcomputer and DSP control in active filters and power supplies. EEL342 DSP based Control of Electric Drive Pre-requisites: EEL203 Features of a DSP in comparison to those of ordinary processors, computational advantage handicaps regarding analog and digital interface. Communication advantages. Harmonic analysis in real time using a DSP specific assembly language features for a DSP. On chip RAM and external RAM I/O interface. PWM and firing pulse generation through a typical DSP, look-up tables and realtime computation. Interfacing and actuation circuits for DSP based controllers. Realization of computationally intensive algorithms like variable structure, adaptive and neural network schemes for drive systems. EEL344 Electric Transportation Pre-requisites: EEL203 Battery powered vehicles: electric cars, pallet truck, fork lift trucks, electric bus, solar powered electric vehicles and boats etc. drives used in electric vehicles, d.c. drives, vector controlled ac motor drives, PMBL motor drives, switched reluctance motor drives, Electric traction, trains, trams and trolleys, nature of tractive loads, supply systems, power factor and harmonics, traction motors and drives, Diesel electric traction, a.c. induction motor drives, marine propulsion systems and aircraft system. EEL346 Electrical Machines and Industrial Drives Pre-requisites: EEL P a g e

171 aspects of electric rotating machines, industrial practices of manufacture and design. Convertor fed operation of d.c. motors, electronically commutated and permanent magnet motors. Electrical Applications in electric traction, steel mill drives, process industries, audio equipment, automobiles, computers and robotics. Computer aided modelling and analysis of d.c. drives. Modelling of synchronous machines. Saliency effects, steady-state and transient. Brushless synchronous generators using electronic circuits, induction motor operation and control. Variable frequency inverter fed motors for drive applications. Power electronics control of a.c. motors with application to variable speed drives. Energy conservation in motors. Microprocessor and microcontroller applications for a.c. drives. Single phase induction motor and applications in domestic appliances, electronic instrumentation, etc. Stepper motor and control applications in robotics, CNC, computer peripherals, permanent magnet motors, switched reluctance motors, linear motors and their applications. Special generators for renewable energy systems such as wind, biogas, small hydro, solar etc. EEL349 Advanced Electrical Machines Pre-requisites: EEL203 Details of PWM inverter fed ac drives with different forms of feedback control, bang-bang and sliding mode structures, realisation on microcomputer based systems. Vector control of ac motor; flux estimators and their shortcomings, hardware realisation, start up control of induction motors with PWM and flux vector structures. Present day shortcomings of inverter fed induction motor drives-bearing erosion, shaft fracture and efficiency problems involvement of soft switching inverters and impact on ac drive performance SR motors and PM motors drive control. Design of power electronic modules and microprocessor controllers. EEL359 Electric Machine Design and CAD of Electric Machines Pre-requisites: EEL203 & EEP203 Basic design methodology and engineering considerations. Properties of electric magnetic and insulating materials. Choice of materials, frames etc. Computerisation of design procedures, Optimization techniques and their application to design problems. Design of large and FHP motors. Database and knowledge based expert systems. Development of PC based software, Exercise on design using standard software. EEL365 Intelligent Control Pre-requisites: EEL301 Conventional control review, Feedback linearization, Robust and adaptive control, Fuzzy system: Introduction to fuzzy logic, Examples, fuzzy logic based identification and control, adaptive fuzzy control, Neural networks: Basics, Neural network based identification and control of nonlinear systems, examples. Various other soft computing 171 P a g e techniques for control applications. Introduction to reinforcement learning. EEL375 Embedded Systems 5 credits (3-0-4) Pre-requisites: EEL308 Overlaps with: CSP413, MEL432, EEL705 Overview of Embedded Systems; Embedded System Architecture: processor examples - ARM, PIC, etc.; features of digital signal processor; SOC, memory subsystem, bus structure (PC-104, I2C etc.), interfacing protocols (USB, IrDA etc), testing and debugging, power management; Embedded System Software: Program Optimization, Concurrent Programming, Real-time Scheduling and I/O management; Networked Embedded Systems: special networking protocols (CAN, Bluetooth); Applications. EEL388 Stepper Motors Pre-requisites: EEL203 Discretisation of angular position by stepper structures, stepping angle and frequency of excitation. VR and PM rotor structures and their torque production, torque angle characteristics. The hybrid structure and torque production by permanent magnet and excitation fluxes. Power electronic converters for stepper motors, control by load angle. Hardware and software based control. Trajectory and motion definition in angle and angular speed. Transfer function of stepper motors, and control of damping by onestep and one-and-a-half step excitation. EEL389 Computer Aided Testing of Electric Machines 3 credits (2-0-2) Pre-requisites: EEL203 Data acquisition system, sensors, transducers such as speed torque, temperature, noise, voltage, current, power, power factor, harmonics, crest factor etc. Digital signal processing and instrumentation. Recorders, computer interface. Case Studies of Computer Aided testing of different electric machines. EEL394 Permanent Magnet Motors Pre-requisites: EEL203 Permanent magnet materials and circuits; Characteristics, parameters, properties, classification and calculations, Permanent magnet motors, D.C. brushed motors, design analysis and control and applications, PM synchronous motors, rotor construction such as surface mounted PM, buried PM, inset type PM and interior type PM rotor and cageless rotor motors, line start and inverter fed control and applications. PM brushless dc motor, theory, operation, control and applications, axial field disc construction, PM step motors, hybrid step motors, sensorless control, reduction of torque pulsations; Case studies such electric vehicles, marine propulsion, spindle drives, commercial and industrial drives, PV fed water pumping.

172 EEL398 Machines and Drives Dynamics Pre-requisites: EEL203 General volt-ampere and torque equations under stationary and orating reference frames. Instantaneous symmetrical components and generalised operational equivalent circuits. Space vector concepts. Modeling of D.C. machines: analysis under motoring and generating. Simulation for transient and dynamic conditions. Modeling of synchronous machines: d-q transformations fixed to field structure steady state and dynamic equations. Phasor diagram for cylindrical rotor and salient pole machineselectromagnetic and reluctance torque. Response under short circuit conditions Modeling of induction machines: Equations under stationary and rotating reference frames, Derivation of equivalent circuits. Correlation of inductances. Run up transients, Dynamics under load change, speed reversal and braking. Unbalanced and asymmetrical operation. Modeling and analysis of permanent magnet, switched reluctance and stepper motors. Development of Computer Software using latest simulation tools to predict the behavior of different machines. EEL404 Flexible AC Transmission System Pre-requisites: EEL303 Concepts of reactive power support and voltage stability. Compensation at a bus and over a line. The synchronous condenser, static var compensation, static phase shifter, thyristor controlled switched capacitor, STATCON s and DVR s, unified power flow controller, interphone power controller. Reactive power balance over a network and optimization. EEL407 Distribution System Planning and Automation Pre-requisites: EEL303 Configuration of distribution systems load characteristics, distribution transformers, distribution substation design, feeder design, voltage regulation, protection in distribution systems, SCADA, distribution automation. EEL423 Demand Side Management Pre-requisites: EEL303 The concepts of demand-side management (DSM) for electric utilities, DSM alternative and goals. End use equipment and control, utility equipment control, energy storage, dispersed generation, customer DSM promotions, performance improvement equipment and system benefit/cost analysis of DSM alternatives; issue in forecasting DSM program impacts. Implementation of DSM programme; pricing and incentives. EEL424 Nuclear Power Generation Pre-requisites: EEL303 Basics of nuclear fission, and characteristics of heavy isotopes. The concepts of beta-decay line, and suitability of nuclear fuels. Fission by fast and slow neutrons, criticality, 172 P a g e and moderation. Types and basic structures of common reactor designs-bwr, HWR and PHWR, power output, size and radiation considerations, operation and control by solid and liquid moderators, neutron density and reactivity control. Point form differential equations for common nuclear reactors core models, moderator dynamics, and thermal circuits. Reactor - poisoning by Xenon and strontium, control of performance to avoid poisoning. Special features of alternators and boilers in nuclear plants. Control and safety standards of nuclear units. EEL428 Substation Design Pre-requisites: EEL303 Types of substations layout and bus bar arrangements Grounding; design nd Practices, substation auxiliaries, Cable routing, data acquisition, substation Control, load shedding, implementation. EEL455 Power System Planning Pre-requisites: EEL303 Load forecasting, generation system reliability, transmission system reliability and distribution system reliability. Generation system expansion planning, Transmission system expansion planning and distribution system expansion planning, Reactive power planning, Integrated power system planning. EEL458 Power Systems Optimization Pre-requisites: EEL303 Characteristics of generation units, economic dispatch of thermal plants, unit commitment hydro thermal coordination maintenance scheduling, emission minimization, optimal power flow, security constrained optimization. EEL482 Mechatronics Pre-requisites: EEL201 & EEL203 & EEL301 Overlaps with: MEL411, MEL432 Mechatronics: definitions and terminology, its elements such as mechanics, electronics, microelectronics, power electronics and information technology. Mechanical elements with integrated electronics suspension systems, vibration dampers, clutches, bearing mechanical or magnetic, gears etc. Machines with integrated electronics, electric drives, pneumatic and hydraulic drives, water steam or gas turbines, combustion engines, etc. Generators, pumps, compressors, machines tools, robots, printing machines, vehicles: automobiles, ships and aircraft. Precision machines with integrated electronics devices for telecommunication, consumer electronics, data processing devices, sensors, actuators, optical devices and medical devices, Power electronics converters.

173 EEL483 Hydro Power Generation Pre-requisites: EEL303 Types of Hydro plants subsystems of hydro plant, turbines, hydro alternates hydro plant. Auxiliaries, control of hydro power, micro hydel systems, special problems in hydro plants. EEL486 Illumination and Heating Pre-requisites: EEL101 / EEL102 and EC 90 Laws of illumination; Types of lamps and fixtures; Energy conservation measures; Electric heating; Electric welding. Pre-requisites: EEL325 Maximization of functional of a single and several functions using calculus of variations, Constrained externals, Necessary conditions for optimal control, Linear regulator problems, Pontryagin s minimum principles and state inequality constraints Minimum time problems, Minimum control effort problems, Singular intervals in optimal control problems, The principle of optimality, Application of the principle of optimality to decision making, Dynamic programming applied to routing problems, Computational steps for solving optimal control problems using dynamic programming, Discrete linear regulator problem, Hamilton - Jacobi -Bellman Equation, Numerical Techniques to determine optimal trajectories, Optimal control of distributed parameter systems. EEL487 Intelligent Algorithms for Power Systems Pre-requisites: EEL303 Introduction of Artificial Neural Networks (ANN), Multilayer feed forward networks, back propagation training algorithm, Radial basis function and recurrent networks. ANN based algorithms for: load flow analysis, economic load dispatch, load forecasting, transient stability, and power system stabilizers. Introduction to genetic algorithms. EEL741 Modeling and Analysis of Electrical Machines Pre-requisites: EEL203 Energy state functions, Modeling of electromechanical systems Matrix method and use of generalized circuit theory of machines. Different methods of transformation, phase variable instantaneous symmetrical component techniques, Development of basic performance equation and analysis of different rotating machines such as D. C., synchronous and induction machines, Dynamics and transients in electric machines. Switching transients and surges, Transient and short circuit studies on alternators Run-up re-switching and other transients in induction machines relevant computer techniques for machine analysis. Modeling of special electrical machines. EEL748 Power Quality Pre-requisites: EEL303 Overview and definition of power quality (PQ) Sources of pollution, international power quality standards, and regulations, Power quality problems: rapid voltage fluctuations voltage unbalance, voltage dips and voltage swells, short duration outages, Power system harmonics: harmonic analysis, harmonic sources- the static converters, transformer magnetization and non-linearities, rotating machines, arc furnaces, fluorescent lighting. Harmonic effects-within the power system, interference with communication Harmonic measurements. Harmonic elimination-harmonic filters. EEL772 Optimal Control Theory 173 P a g e

174 Department of B.Tech, B.Tech + M.Tech Electronics & Communications EEL101 Fundamentals of Electrical 4 credits (3-0-2) Overlaps with: EEL102 DC circuits, KCL, KVL, Network theorems, Mesh and nodal analysis, Step response and transients. RC, RL and RLC circuits, Phasor diagram solution of AC circuits. Power in 1- and 3-phase AC circuits. Two port networks. Operational amplifiers: model and applications. Magnetic circuits. Transformers: modeling and analysis. Energy in magnetic field, production of force and EMF. Electro-mechanical energy conversion. Principles of measurement. Electrical and electronic materials. Laboratory experiments will be based on these topics. EEL205 Signals and Systems 4 credits (3-1-0) Pre-requisites: EEL101 / EEL102 / MAL110 / MAL111 /MAL115 Classification of signals and systems, various system representation techniques, differential, difference and statespace representations, Fourier transforms and series, application to analysis of systems, Laplace transform, its properties, and its application to system analysis, Ztransforms, its properties and applications, Random variables and random process, characterization of random variables and random process, linear systems and random signals. EEL202 Circuit Theory 4 credits (3-1-0) Pre-requisites: EEL101 / EEL102 Overview of network analysis techniques, Network theorems, Transient and steady state sinusoidal response. Network graphs and their applications in network analysis. Tellengen s theorem, Twoport networks, z, y,h and transmission parameters, combination of two ports, Analysis of common two ports, Resonance, Coupled circuits, Scattering matrix and its application in network analysis. Network functions, parts of network functions, obtaining a network function from a given part. Network transmission criteria; delay and rise time, Elmore s and other definitions of cascading. Elements of network sythesis techniques. Butterworth and Chebyshev Approximation. EEL201 Digital Electronic Circuits 4 credits (3-1-0) Pre-requisites: EEL101 / EEL102 Review of Boolean Algebra, Karnaugh Map and Logic Gates;Designing combinational Circuits using gates and/or Multiplexers; Introduction to logic families: TTL, ECL, CMOS; PLAs and FPGAs; Sequential Circuits: Flip Flops,Counters and Registers; Design of Sequential Circuits: STD and applications; Pipelining and Timing issues; Memories. EEP201 Electronics Laboratory - I 1.5 credits (0-0-3) Pre-requisites: EEL101 / EEL102 The laboratory is divided into two parts. In the first part, the student is required to perform some set experiments to familiarize himself/ herself with basic digital electronic techniques. In the second half of the semester, the student is required to design and fabricate a digital module. A formal presentation of the design is required at the end of the semester. EEL204 Analog Electronics Circuits 4 credits (3-1-0) Pre-requisites: EEL101 / EEL102 Review of working of BJT, JFET and MOSFET and their small signal equivalent Circuit; Biasing of BJT, JFET and MOSFET circuits; Analysis and Design of various single stage amplifier configurations; Multi Stage Amplifiers; Differential Amplifier and Operational Amplifier; Feedback Amplifiers; Tuned Amplifiers; Oscillators. EEL301 Control - I 4 credits (3-1-0) Pre-requisites: EEL205 Overlaps with: MEL312, CHL261 Introduction to the control problem, Industrial control examples, Transfer function models of suitable mechanical, electrical, thermal and pneumatic systems. Systems with dead time, Control hardware and their models: Potentiometers, synchros, LVDT, DC and AC servo motors, tachogenerators, electro-hydraulic valves, pneumatic actuators. Closed loop control systems, Block diagram and signal flow analysis, Basic Characteristics of feedback control systems : stability, steady-state accuracy, transient accuracy, disturbance rejection, insensitivity and robustness.basic modes of feedback control :Proportional, Integral, Derivative. Concept of stability and Routh stability criterion.time response of 2nd order system, steady state error and error constants, Performance specifications in the time domain. Root locus method of design. Lead and lag compensation. Nyquist stability criterion. Frequency response analysis: Nyquist plots, constant M circles, constant N-circles, Bode plots, Nichols Charts Performance specifications in frequency domain, Frequency-domain methods of design. Lead and lag. EEP204 Electronics Laboratory - II 1.5 credits (0-0-3) Pre-requisites: EEL101 / EEL102 To design and test single stage and multi stage amplifiers, power amplifiers and oscillators on bread board. The students will be given the specification and the design to be verified before wiring up the circuit. The students are encouraged to trouble shoot with hints from the instructor and TAs. 174 P a g e

175 Pre-requisites: EEL306 Laboratory experiments on analog, pulse, and basic digital modulation and demodulation techniques. EEP301 Control Laboratory 1.5 credits (0-0-3) Pre-requisites: EEL301 First and Second Order Electrical Systems, A.C and D.C Servo Motors, Synchro Characteristics, D.C Integral Servo Systems, Characteristics of Hydraulic Servo, Amplifier and Servo motor, Pneumatic Process Controller, Process Control Simulator, Microprocessor based speed control of stepper motor. EEL207 Electromagnetics 4 credits (3-1-0) Pre-requisites: PHL110 Review of Maxwell s equations, wave propagations in unbounded medium.boundary conditions, reflection and refraction of plane waves.transmission Lines: distributed parameter circuits, traveling and standing waves, impedance matching, Smith chart, analogy with plane waves.waveguides: parallel-plane guide, TE, TM and TEM waves, rectangular and cylindrical waveguides, resonators.planar transmission lines: stripline, microstripline, application of numerical techniques.dielectric guides and optical fibres.radiation: retarded potentials, Hertzian dipole, short loop, antenna parameters.radio-wave propagation: ground-wave, skywave, space-wave. EEP307 Electromagnetics Laboratory 1.5 credits (0-0-3) Pre-requisites: EEL207 Laboratory experiments on different transmission lines, antennas, microwave sources and passive devices. EEL306 Communication 4 credits (3-1-0) Pre-requisites: EEL205 Review of Fourier Series and Transforms. Hilbert Transforms, Bandpass Signal and System Representation. Random Processes, Stationarity, Power Spectral Density, Gaussian Process, Noise. Amplitude Modulation, SBSC, SSB, VSB: Signal Representation, Generation and Demodulation. Frequency Modulation: Signal Representation, Generation and Demodulation. Mixing, Superheterodyne Receiver, Phase Recovery with PLLs. Noise: in AM Receivers using Coherent Detection, in AM Receivers using Envelope Detection, in FM Receivers. Sampling, Pulse-Amplitude Modulation. Quantization, Pulse-Code Modulation. Noise Considerations in PCM, Time Division Multiplexing, Delta Modulation. EEP306 Communication Laboratory 1.5 credits (0-0-3) EEL308 Computer Architecture 4 credits (3-1-0) Pre-requisites: EEL201 Overlaps with: CSL211 Organization of a Computer: von Neumann and Harvard architecture; Instruction Set Architecture: RISC and CISC processors; Computer Arithmetic: fixed point and floating point arithmetic; Design of ALU: hardware algorithms for addition, multiplication and division of fixed point and floating point numbers; Processor design: Data Path and Control Design, Microprogramming, Exception Processing, Pipelining; Memory Organisation: memory hierarchy, cache organization, virtual memory; System Design: bus structure, bus transactions; Input-output Systems: programmed I/O, DMA and interrupt driven I/O. Illustrations with examples of CISC processors from Intel and RISC processors like MIPS and ARM. EEL442 OP-AMPS and Linear Integrated Circuits Pre-requisites: EEL204 Differential amplifier with its configurations and analysis, basic building block of OP-AMP, inverting and non inverting configurations, terminologies and parameters, IC741 and its applications. EEL321 Digital Hardware Design 4 credits (3-0-2) Pre-requisites: EEL201 Overlaps with: CSL316 Review of combinational and sequential logic; Finite state machines and optimization of finite state machines; Hardware Description Languages (HDL), HDL based design; Introduction to data path and control path synthesis; Asynchronous state machine based design; Considerations of technology; testability and faulttolerance in design. EEP205 Signal Processing Lab-I 1 credits (0-0-2) Using MAT LAB software generation of continuous,discrete,unit,periodic, aperiodicgeneration of Exponential and Ramp signals in Continuous & Discrete domain. Adding and subtracting two given signals, Convolution, random binary wave and random sequences. EEL316 Digital Communications 4 credits (3-0-2) Pre-requisites: EEL306 Matched Filter, Error Rate due to Noise. Intersymbol Interference, Nyquist s Criterion, Duobinary Signaling. Optimum Linear Receiver. Geometric Representation of Signals. Coherent Detection of Signals in Noise, Probability of Error. Coherent Digital Modulation Schemes: MPSK, 175 P a g e

176 MFSK, MQAM; Error Analysis. Noncoherent FSK, Differential PSK. Comparison of Digital Modulation Schemes, Bandwidth Efficiency. Pseudo-Noise Sequences and Spread Spectrum. Information Theory, Entropy, and Source-Coding. EEL441 Industrial Electronics 4 credits (3-0-2) Pre-requisites: EEL101 / EEL102 and EC 90 Power electronic components- thyristors, triacs, GTOs, MOSFETs and other bipolar devices and their switching properties. Introduction to thyristorised phase controlled rectifiers and dual converters. AC controllers and timers, dimmers, heating. SMPS and UPS systems. Introduction to AC controllers, inverters, choppers, cycloconverters. Introduction to converter fed AC and DC drives-their performance. Other applications of power electronics. EEL713 Microwave Theory and Circuits Pre-requisites: EEL207 Review of EM theory: Maxwell s equations, plane waves in dielectric and conducting media, energy and power.transmission lines and waveguides: closed and dielectric guides, planar transmission lines and optical fibre.network analysis: scattering matrix other parameters, signal flow graphs and network representation. Impedance matchingand tuning.analysis of planar transmission lines.analysis of design of passive components. EEL318 Microprocessor 4 credits (3-0-2) Introduction of 8085 microprocessor, 8085 architecture, instruction set and 8085 microprocessor interfacing. EEL319 Digital Signal Processing 4 credits (3-0-2) Pre-requisites: EEL205 Overlap with: EEL731 Review of Signals and Systems, Sampling and data reconstruction processes. Z transforms. Discrete linear systems. Frequency domain design of digital filters. Quantization effects in digital filters. Discrete Fourier transform and FFT algorithms. High speed convolution and its application to digital filtering. EEL338 Antennas and Propagation Pre-requisites: EEL207 Antennas: Introduction to various types of antennas. Fundamentals of electromagnetic radiation, radiation from thin wires and small loops. Different types of linear arrays. Pattern multiplication, long wire antennas, aperture antennas. Waveguides. EEC420 Colloquium (EP) 3 credits (0-3-0) 176 P a g e Pre-requisites: registered for EET420 Students will deliver talks about their experience during practical training, and on topics of current interest. EED421 Major Project Part 1 (ECE) 4 credits (0-0-8) Pre-requisites: EC 120 Formation of project team (up to two students and two faculty guides); formulation of work plan; completion of targeted work for the semester; and presentation of progress for award of grade. Topic could be from any area of electrical engineering. Completion of about a third of the total work for assessment and grading. EEL329 VLSI Technology and Design 4 credits (3-0-2) Pre-requisites: EEL201 Overlaps with: EEL734 MOS transistors. CMOS and Pseudo NMOS inverters. Pass transistors. Designing Logic gates in CMOS. CMOS sequential circuits. Timing issues, Basic CMOS technology, Layout design rules and CMOS gate layout, Circuit and Logic simulation. Layout generations- partitioning, placements and routing. EEL334 Wireless Communication Propagation phenomena - Fundamentals of fading, Multipath channels, line of sight microwave communication, multiple access techniques, cellular wireless networks, and satellite communication EED412 Major Project Part 2 (ECE) 8 credits (0-0-16) Pre-requisites: EED411 Continuation of planned tasks started in Project Part 1 to completion, thesis writing and presentation of complete work for award of grade. Completion of the planned work for assessment and grading. EEL204 Analog Electronics Circuits 4 credits (3-1-0) Pre-requisites: EEL101 / EEL102 Review of working of BJT, JFET and MOSFET and their small signal equivalent Circuit; Biasing of BJT, JFET and MOSFET circuits; Analysis and Design of various single stage amplifier configurations; Multi Stage Amplifiers; Differential Amplifier and Operational Amplifier; Feedback Amplifiers; Tuned Amplifiers; Oscillators. EEL322 Integrated Circuits Technology Pre-requisites: EEL204 Fabrication of active and passive devices and integrated circuits. Basic technological steps pattern definition,

177 impurity introduction, layer deposition, etching. Simplified process sequences for bipolar, NMOS and CMOS. EEL347 CMOS VLSI Design The basic MOS inverter, transfer characteristics, logic threshold. NAND and NOR logic. Transit times and inverter pair delay. Depletion and enhancement loads. Technological options in MOS processing. CMOS. Design considerations in combinational logic, shift register arrays. Register to register transfers. MOS memories and programmable logic arrays. Non-volatile memories with MOS technology. Short channel structures. Scaled down MOS performance. Other MOS LSI considerations. EEL732 Microelectronics Brief recapitulation : Band theory, F-D statistics. Recombination effects and bipolar junction devices. MOS Devices : MOS capacitance ideal characteristics. Interface effects and characterisation. MOSFET principles,and charateristics. Various MOSFET structures, viz. DMOS, VMOS etc. and some typical applications. Parasitic device effects in MOSFET and bipolar circuits. EEL319 Digital Signal Processing 4 credits (3-0-2) Pre-requisites: EEL205 Overlap with: EEL731 Review of Signals and Systems, Sampling and data reconstruction processes. Z transforms. Discrete linear systems. Frequency domain design of digital filters. Quantization effects in digital filters. Discrete Fourier transform and FFT algorithms. High speed convolution and its application to digital filtering. EEL475CAD For VLSI Hardware description Languages; Verifying behaviour prior to system construction simulation and logic verification; Logic synthesis; PLA based synthesis and multilevel logic synthesis; Logic optimization; Logic Simulation: Compiled and Event Simulators; Relative Advantages and Disadvantages; Layout Algorithms Circuit partitioning, placement, and routing algorithms; Design rule verification; Circuit Compaction; Circuit extraction and post-layout simulation; Automatic Test Program Generation; Combinational testing : D Algorithm and PODEM algorithm; Scan-based testing of sequential circuits. EEL358 Operating Systems Pre-requisites: EEL308 Overlaps with: CSL373, MAL358, EEL602 Introduction to OS; Process and Thread management; Scheduling;Concurrent threads and processes: mutual exclusion, synchronization,inter-process communication; 177 P a g e Memory management: Cache and VirtualMemory management; Resource management: deadlock and its prevention; File management; I/O management;introduction to realtime systems; Elements of distributed operating systems. EEL208 Electronic Devices and Circuits Pre-requisites: EEL101 / EEL102 Review of working of BJT, JFET and MOSFET and their small signal equivalent Circuit; Biasing of BJT, JFET and MOSFET circuits; Analysis and Design of various single stage amplifier configurations; Multi Stage Amplifiers; Differential Amplifier and Operational Amplifier; Feedback Amplifiers; Tuned Amplifiers; Oscillators. EEL313 Signals System Pre-requisites: EEL101 / EEL102 / MAL110 / MAL111 /MAL115 Classification of signals and systems, various system representation techniques, differential, difference and statespace representations, Fourier transforms and series, application to analysis of systems, Laplace transform, its properties, and its application to system analysis, Ztransforms, its properties and applications, Random variables and random process, characterization of random variables and randomprocess, linear systems and random signals. EEL314 Communication Theory 4 credits (3-1-0) Pre-requisites: EEL205 Review of Fourier Series and Transforms. Hilbert Transforms, Bandpass Signal and System Representation. Random Processes, Stationarity, Power Spectral Density, Gaussian Process, Noise. Amplitude Modulation, SBSC, SSB, VSB: Signal Representation, Generation and Demodulation. Frequency Modulation: Signal Representation, Generation and Demodulation. Mixing, Superheterodyne Receiver, Phase Recovery with PLLs. Noise: in AM Receivers using Coherent Detection, in AM Receivers using Envelope Detection, in FM Receivers. Sampling, Pulse-Amplitude Modulation. Quantization, Pulse-Code Modulation. Noise Considerations in PCM, Time Division Multiplexing, Delta Modulation. EEL333 Communication Theory-II Pre-requisites: EEL306 Matched Filter, Error Rate due to Noise. Intersymbol Interference, Nyquist s Criterion, Duobinary Signaling. Optimum Linear Receiver. Geometric Representation of Signals. Coherent Detection of Signals in Noise, Probability of Error. Coherent Digital Modulation Schemes: MPSK, MFSK, MQAM; Error Analysis. Noncoherent FSK, Differential PSK. Comparison of Digital Modulation

178 Schemes, Bandwidth Efficiency. Pseudo-Noise Sequences and Spread Spectrum. Information Theory, Entropy, and Source-Coding. Fading channel models and characterization: Scatter model. Scatteringfunction. Classification of channels (dispersive only in time, only in frequency, doubly dispersive). Modulation and demodulation :Optimum receiver principles, structure of modulators anddemodulators. Combining techniques. General principles of linearcombining, selection combining, maximal ratio combining and equal gain combining. Decision oriented diversity, optimum combining.coding for fading channels. Trivial repetitive coding, Interleavedcoding, dual- 178 P a g e k convolutional codes and trellis codes for fading channels. Performance evaluation. Random coding bound for coded systems, probability of error, bandwidth and complexity. Performanceof linear combining systems. Examples of fading channels : Discussion on mobile communication channels and troposcatter channels. EEL336Advanced Signal Processing 4 credits (3-1-0) Pre-requisites: EEL205 Overlap with: EEL731 Review of Signals and Systems, Sampling and data reconstruction processes. Z transforms. Discrete linear systems. Frequency domain design of digital filters. Quantization effects in digital filters. Discrete Fourier transform and FFT algorithms. High speed convolution and its application to digital filtering. EEL434 Optical Communication Pre-requisites: EEL306 Overlaps with: EEL712 Introduction to optical communication, review of optical sources, fiberand detector, optical signaling schemes viz., IM, PL, PCM, PCM/PL,digital PPM, PFM, PAM. Various receiver configurations - direct detection,homodyne and heterodyne receivers, Noise sources in opticalcommunication - modal noise, speckle noise, shot noise, phase noise,thermal noise, Integrated and transimpedance amplifiers, optical linecoding, performance evaluation of optical receivers for variousmodulation and demodulation schemes and their comparative study.diversity receivers-phase and polarization diversities. Optical fiber linkdesign, fiber optics networks, introduction to optical space communication. EEL474 Antenna Fundamentals 4 credits (3-1-0) Pre-requisites: EEL207 Antennas: Introduction to various types of antennas. Fundamentals of electromagnetic radiation, radiation from thin wires and small loops. Different types of linear arrays. Pattern multiplication, long wire antennas, aperture antennas. Waveguides. EEL436 Mobile Communication EEL471Telecommunication and Switching Networkss Pre-requisites: EEL306 Basic line circuits, long haul circuits, signaling, switching exchanges,analysis of telecom switching networks, teletraffic engineering,management protocols, multi-service telecom protocols and networks. EEL343 Integrated Circuits Pre-requisites: EEL204 Fabrication of active and passive devices and integrated circuits. Basic technological steps pattern definition, impurity introduction, layer deposition, etching. Simplified process sequences for bipolar, NMOS and CMOS. EEL345 Digital System Design 4 credits (3-1-0) Pre-requisites: EEL201 Overlaps with: CSL316 Review of combinational and sequential logic; Finite state machines and optimization of finite state machines; Hardware Description Languages (HDL), HDL based design; Introduction to data path and control path synthesis; Asynchronous state machine based design; Considerations of technology; testability and faulttolerance in design. EEL439Operational Amplifier Pre-requisites: EEL204 Differential amplifier with its configurations and analysis, basic building block of OP-AMP, inverting and non inverting configurations, terminologies and parameters, IC741 and its applications. EEL429Microelectronic Circuits Brief recapitulation : Band theory, F-D statistics. Recombination effectsand bipolar junction devices. MOS Devices : MOS capacitance ideal characteristics. Interface effects and characterisation. MOSFET principles and charateristics. Various MOSFET structures, viz. DMOS, VMOS etcand some typical applications. Parasitic device effects in MOSFET and bipolar circuits. Other devices : High frequency transistors. Metal Semiconductor contacts (Schottky diodes) and MESFET.Device Modelling : Bipolar devices Gummel Poon model and RC distributed model.mos devices - Long channel modes, short channel

179 structures and scaled down device models, sub-threshold conduction. EEL476 Analog Mixed Signal ICs 4 credits (3-1-0) Review of bipolar and unipolar transistor models. Theory and design ofoperational amplifiers. Definition and measurement of performance characteristics. Linear and non-linear applications. D/A and A/Dconverters. MOS operational amplifiers, timers, Function generators.multipliers. 46 Department of B.Tech, B.Tech + M.Tech Mechanical AML110 Mechanics 4 credits (3-0-2) Laws of mechanics, equivalent force systems and equations of equilibrium, Internal forces in structures and beams, friction and its applications, Kinematics of point mass and rigid body, Center of mass, System of particles, Inertia tensor, Dynamics of rigid bodies, Euler s equations of motion, Impulse-momentum, Work-energy methods with applications, Principle of virtual work and stability. AML140 Mechanics of Solids 4 credits (3-1-0) Overlaps with: AML150, AML180 Introduction, Definition of stress, Equations of equilibrium, Principal stress, Maximum shear stress, Plane stress, Concept of strain, Strain displacement relations, Principal strains, Plane strain, Constitutive relations, Uniaxial tension test, Idealized stress-strain diagram, Isotropic linear elastic, viscoelastic and plastic materials, Uniaxial deformations, Thermal stresses, Torsion of shafts, Bending and shear of beams, Energy methods, Fracture, Deflection, Stability. AML160 Mechanics of Fluids 4 credits (3-1-0) Overlaps with: AML150, AML170, CHL231, CHL204 Introduction. Definitions. Fluid properties: classification of fluids and flow regimes. Fluid statics: Stationary fluids and liquids subjected to constant linear acceleration and to constant rotation. Fluid kinematics: Lagrangian and Eulerian descriptions, pathlines, streaklines and streamlines, acceleration. Integral flow analysis: Reynolds transport theorem, conservation of mass/continuity equation and conservation of linear and angular momentum for a control volume in inertial and accelerating reference frames, energy equation, Bernoulli s equation, engineering applications. Differential analysis of flow: Continuity and Navier-Stokes equations. Dimensional analysis and Similitude theory. Inviscid flows: Irrotational flow, circulation, velocity potential and applications. Viscous flows in pipes and ducts. External viscous flows: concept of boundary layer, momentum integral equation, drag and lift, separation. Fluid machinery: Introduction and classification of machines, types of hydraulic turbines and pumps and their performance characteristics, turbomachinery analysis and velocity triangles, cavitation, NPSH concept, similarity rules, applications. 179 P a g e AMP261 Solids Laboratory 1.5 Credits (0-0-3) Experiments related to course AML140. Experiments will be conducted in a group of two students. A professional report is to be prepared for each experiment. AMP262 Fluids Laboratory 1.5 Credits (0-0-3) Experiments related to course AML160. Application of uncertainty analyses. Experiments will be conducted in a group of two students. A professional report is to be prepared for each experiment. MEC410 Colloquium (ME) 3 credits (0-3-0) Pre-requisites: Registered for MET410 Introduction to planning, preparing and making presentations preparation of slides, time management, communication aspects, etc. Making a presentation on practical training with response sheet for testing audience. Reading an assigned project report, making a presentation with audience response sheet and a critique on writing style, completeness and editorial get-up. Performing patent searches on an allotted product and making a presentation using diagrams/figures only. Preparing posters on practical training and presenting these at a poster session. MEL110 Graphic Science 2 credits (0-0-4) Orthographic, Axonometric, Isometric, Oblique, Perspective projections. Lettering, instruments and line work, free hand sketching, plane geometric constructions, auxiliary planes. Intersection and development of surfaces, planes and solids with their spatial relationships. Transition pieces, rules and conventions for sectioning and dimensioning. Introduction to computer aided drawing. Examples of graphic communication. MEL120 Manufacturing Practices 4 credits (2-0-4) The objective of the course is to expose students to basics of manufacturing as it plays a direct role in improvement of quality of human life and creating wealth for the nation. The second objective of the course is to expose students to hands-on practice with common manufacturing processes. It will cover: (i) importance of manufacturing, (ii) relation between materials and manufacturing, (iii) an overview of manufacturing processes, (iv) product manufacturing, (v) importance of product assembly and inspection, (vi) an overview of manufacturing planning, and (vii) manufacturing automation and computer aided manufacturing for industry. MEL140 Thermodynamics 4 credits (3-1-0) Introduction to applications. Basic concepts and definitions system, boundary, equilibrium, steady state and others.

180 Thermodynamic properties of a pure substance saturated and other states. Work and heat definition and applications. 1st Law internal energy and enthalpy, applications to non-flow/closed and flow/open systems (SSSF and USUF), reacting systems and gas-vapor mixtures. 2nd Law corollaries, Clausius inequality, entropy. Introduction to availability, irreversibility and exergy. Carnot cycle. Basics of gas-vapor mixtures and reacting systems. Vapor power cycles Rankine cycle and its modifications. Air standard cycles Otto, Diesel, Brayton cycles. Vapor compression and absorption refrigeration cycles. Material deformation, electromagnetics and other applications. MEP201 Mechanical Drawing 3 credits (1-0-4) Pre-requisites: MEL110 Introduction to design process and drawings. Review of sectioning, drawing standards, dimensioning and notes. Fasteners screws, bolts and nuts, riveted joints, pins, locking devices, welded joints, pipe joints, unions and valves. Assembly drawings with sectioning and bill of materials. Cotter and Knuckle Joints. Assemblies involving machine elements like shafts, couplings, bearing, pulleys, gears, belts, brackets. Tool drawings including jigs and fixtures. Engine mechanisms-assembly and disassembly. Detailed part drawings from assembly drawings. Production drawings - limits, fits and tolerances, dimensional and geometric tolerances, surface finish symbols. Layout drawings. Schematics, process and instrumentation diagrams, piping drawings. Structural drawings - examples for reading and interpretation. Computer aided design and use of software packages for engineering drawings. MEL202 Quality & Management Systems Quality: Basic concepts and definitions of Quality, Quality Gurus, Quality System awards and guidelines, Quality measures, Dimensions of quality, cost of quality, Elements of quality, Statistics for Quality, Fundamentals of statistics for quality, Product Quality control: Acceptance Sampling Methods, Process Evaluation and Control by control charts, Total Quality Management, Quality Circles, Quality Policy Deployment, ISO 9000, Quality Circles, Quality Policy Deployment, 5S, role of Kaizen in TQM, Total Productive maintenance, Concurrent, JIT, Kanban, Poka Yoke, Process capability, Fault Tree Diagrams, Cause and Effect Diagrams, DOE: Concept of DOE, Types of experiments, Six Sigma, Reliability. MEL211 Kinematics and Dynamics of Machines 4 credits (3-0-2) Pre-requisites: AML110 & MEL110 Kinematic pairs, diagram and inversion. Mobility and range of movements. Displacement, velocity and acceleration analysis of planar linkages. Dimensional synthesis for motion, function and path generation. Cam profile synthesis. Gears dynamic force analysis, flywheel, inertia forces and their balancing for rotating and reciprocating machines. Hydrodynamic and boundary lubrication in journal and thrust bearings. Experiments will be performed 180 P a g e on Kinematics link, chains and pairs, Four bar mechanism, belt and pulley, Gears, Cam and follower, governors and balancing machine etc. MEL221 Operations Research 4 credits (3-1-0) Pre-requisites: MAL120 Introduction to Industrial and Operations Research, Role of modeling, Nature of Problems, Graphical method, Simplex method, various cases of LP problems, Duality, Sensitivity, Special topics like Transportation problem, assignments, inventory, Queuing System, Project management etc. MEL232 Casting, Welding and Forming 4 credits (3-0-2) Pre-requisites: MEL120 Overlaps with: MEL231 Study of metal casting processes; Study of welding and other joining processes; Study of metal forming processes; Processing of plastics; Process planning and process analysis casting, welding and forming processes; Economic and quality issues in casting, welding and forming processes. Laboratory activities on study of bulk and sheet forming processes, dies and presses for forming, conventional and unconventional machining processes. MEL233 Machining, Machine Tools and Metrology 4 credits (3-0-2) Pre-requisites: MEL120 Overlaps with: MEL234 Introduction to machine tools and machining operations. Mechanics of metal machining. Cutting forces, friction, cutting fluids and surface finish, lubrication, temperatures and heat transfer and its measurement, tool life and tool wear aspects. Theoretical models of shear angle solution, Basic concepts of cost and economics of metal cutting operations, Tool nomenclature, chip control and design for machining. Construction of Machine tools, alignment, metrology and inspection. Metrology: Introduction to Metrology and its relevance, standardization, dimensional measurement, limits, fits and tolerances, limit gauging, linear and angular measurements and their applications, surface roughness quantification and measurement, alignment testing of machine tools, feature inspection etc. MEL241 Energy Conversion 4 credits (3-0-2) Pre-requisites: MEL140 Overview of energy conversion technologies. Combustion and applications IC engines, burners, furnaces and components. Compressible flow fundamentals Mach number, normal shock, adiabatic 1-D flow through variable area passages. Turbo-machinery flow through a stationary and moving passage, velocity triangles, impulse and reaction principles, characteristics and components of axial and centrifugal turbo-machines. Refrigeration and air

181 conditioning system analysis, components design, psychometric, and air-conditioning calculations. Steam generation and its use power plants, co-generation, combined cycles. Steam and gas turbine construction and performance. Equipment studies and performance calculations in the laboratory will concurrently accompany lectures. MEL242 Heat and Mass Transfer 4 credits (3-1-0) Pre-requisites: AML160 Modes of heat transfer in various applications. Conduction: Heat diffusion equation, 1-D steady state conduction in extended surfaces, infinite and semi-infinite walls, heat generation, lumped capacitance and simple transient models. Convection: Forced and free convection - mass, momentum and energy conservation equations, nondimensional numbers, hydrodynamic and thermal boundary layers, basics of heat transfer in external and internal laminar and turbulent flows, and use of co-relations. Boiling and condensation: physical phenomena and co-relations. Mass transfer Fick s law, similarity with convection and correlations. Radiation: properties, Laws, 3-surface network for diffuse gray surfaces. Heat exchanger fundamentals and design. MEL310 Concurrent 4 credits (3-1-0) Concurrent - meaning and need. Review of Problem Solving methods. Description of methods of Analysis, Decision Making, Creativity and Information processing and their role in engineering. Discussion of Emerging engineering strategies of Total Design, Design for Manufacturing and Assembly, Quality Function Deployment, and Constraint networks. Integrating concurrent approaches with those of conventional. Implementation of concurrent engineering in industrial environment especially those of IT and high speed computation. MEL311 Machine Element Design 5 credits (3-1-2) Pre-requisites: MEL211 & AML140 && MEP201 & MEP202 Mechanical Design vis-à-vis Solid Mechanics, factor of safety, standards and design equations. Selection of materials and processes. Standard numbering system including BIS designations of materials. Application of theories of failure to design. Design procedure and its application to static strength. Design of elements subjected to simple loading: screws including power screws, bolted joints including eccentrically loaded joints, axles, and coupling, clutches and brakes. Introduction to design for fatigue strength. Endurance and modifying factors. Surface strength. Review of design procedure of fatigue failure with application to the design of bolts and springs subjected to fatigue loading. Design of shafts, spur, helical, bevel and worm gears, journal and rolling contact bearings, belts and chains. Introduction to CAD. Design exercises of systems like those of mechanical drives which may also involve the assistance of a computer. MEL312 Control Theory and Applications 5 credits (3-1-2) Pre-requisites: MAL110 & AML110 & (EEL101 / EEL102) Overlaps with: EEL301/CHL261/MEL334 Introduction to automatic controls. Modeling of flow, heat transfer and electrical, pneumatic and vibration systems. Block diagram and transfer function. Modeling of continuous systems. Extraction of reduced order models. Transient and frequency response evaluation using Laplace transform. Characteristics of hydraulic controller, pneumatic, electronic controller, electro-hydraulic and electro-pneumatic controllers. PID control. Stability. Gain and phase margins. Control system design using root and compensation. Application to Machine tool, Boiler, Engine Governing, Aerospace, Active vibration control, etc. Autotuning. Sequence control, Logic diagram. Introduction to digital control, Implementation using computer. Introduction to control of MIMO systems. State Space modeling. Practical include studies on hydraulic, pneumatics, electronic controller. Control of various parameters such as speed, temperature, level, pressure, etc. Tutorials for control problems in these areas using MATLAB. MEL314 Noise 4 credits (3-0-2) Pre-requisites: MAL110 / MAL120 and EC 60 Overlaps with: ITL760 Fundamentals of vibrations, vibrations of strings and bars, Vibrations of membranes and plates. Acoustic wave equation, Acoustic energy and sound intensity. Propagation of sound, Concept of Acoustic impedance. Sound power transmission, Transmission Loss. Human Response and ratings, Various Measures of Sound. Weighting filters, Loudness, Indices of Loudness. Acoustic radiation from spherical source and piston source. Acoustic sensors. Measuring Techniques and Instruments, Octave Filtering, Sound Intensity Measurement, Intensity Mapping. Different types of measurement environment and uses. Response of beam subjected to an acoustic plane wave. Transmission loss of panels. Sound absorption coefficient. Noise control measures in building. Reverberation time and auditorium design. Industrial Noise control, Noise in Machinery, Traffic Noise, Vehicle Noise. Design of silencers and mufflers. Active noise control. Duct noise control and cabin noise control. Practical on noise measurements in different situations. MEL316 Mechanical Vibrations 4 credits (3-0-2) Pre-requisites: MEL211 Vibration of single degree of freedom (SDF) system. Modelling of stiffness and damping (both Viscous and Coulomb). Estimation of damping by decay plots and half power method. Impulse, transient and forced vibration response of SDF system. Theory and practice of vibration 181 P a g e

182 isolation. Vibration measuring instruments. Two degree freedom system. Application to undamped and damped absorbers. Multidegree freedom systems. Modal analysis. Rayleigh s and Dunkerley s method. Holzer s and Myklestad-Prohl transfer matrix methods. Continuous systems governed by wave equation and Euler Bernoulli equation. Free and forced vibrations including modal analysis. Finite element based dynamic analysis of simple systems. Introduction to modal testing and system identification problems. Industrial applications - rotors and other systems, balancing, vibration standards, vibration monitoring. MEL321 Ergonomics 4 credits (3-0-2) Pre-requisites: MEL221 Introduction to Ergonomics: Definition and importance of ergonomics, History of Ergonomics; Introduction to Humanmachine systems ;Human-machine systems Interfaces; Ergonomics at the Workplace: Anthropometrics principles; Work-related Musculoskeletal Disorders; Workplace Design; Environmental Factors at Work; visual environment; thermal environment; auditory environment; Vibration; Ergonomic Workplace Analysis: Introduction to workplace analysis; Ergonomics workplace analysis; Ergonomic awareness checklist; Legal and safety issues, Various case studies. MEL322 Operations Planning and Control Pre-requisites: MEL221 Production systems and performance measures. Life Cycle of a production system. Major managerial decisions in the life of a production system, Product design and process selection. Location and Layout of production systems, Product, Process and Cellular layouts, Demand Forecasting, Aggregate production planning, Inventory and MRP, Scheduling decisions and emerging trends. MEL325 Production -I Foundry Technology: Casting, Patterns: types, material and design including pattern allowances. All types of castings, Forming Processes: Classification; Hot working and cold working; Forging: Classification; Forging dies; Rolling: Characteristics and applications, Extrusion; Press tool works; Shearing; Drawing; MEL332 Design and Manufacturing of Composites 4 credits (3-0-2) Pre-requisites: MEL120 & AML140 and EC P a g e FRP Composites, fiber types, fiber forms and properties, matrices type and properties, lamina, laminate, orthotropy, anisotropy, composites macro and micro-mechanical analysis and properties, Failure theories -Tsai-Hill, Tsai- Wu, Primary and Secondary Manufacturing - Lay-up, Autoclave Molding Filament Winding, Pultrusion, Compression Molding, RTM, RIM, SRIM, Machining, drilling, routing etc., design, structural and testing, applications. Metal Matrix Composites and Ceramic Matrix composites - Manufacturing routes and applications. MEL333 Metrology 4 credits (3-0-2) Pre-requisites: MEL233 Introduction to Metrology and its relevance, standardization, dimensional measurement, limits, fits and tolerances, limit gauging, linear and angular measurements and their applications, surface roughness quantification and measurement, alignment testing of machine tools, feature inspection and Computer Aided inspection. MEL334 Low Cost Automation 4 credits (3-0-2) Pre-requisites: MEL233 / MEL234 Overlaps with: MEL312/EEL301/CHL261 Introduction, Types of systems - mechanical, electrical, electronics, fluidics; Hydraulics Systems and components; Pneumatic Systems Control; Sequence operation of more than two cylinders and motors; Applications of relays/switches; Measuring systems, Transducers; Feedback control systems; Programmable controllers; Small components feeders; Automatic orientation and assembly; Design of components for assembly. Cost considerations and case studies. Laboratory work will be hands-on design and operation of automatic systems. MEL339 Production -II 4 credits (3-1-0) Metal Joining Processes, types of welding s, Powder Metallurgy, Properties and process of Powder processed materials, Rapid Prototyping Operations: Plastic Technology: Classification of Plastics, Ingredients of Moulding compounds, moulding processes. Introduction to process planning, part print analysis, make-or-buy decision, product drawing analysis, establishing the sequence of processes, economic processing considerations, machine selection, tooling costs, process documentation, operation sheets, tolerance charting, computing dimensions and tolerances and computer aided process planning. MEL341 Gas Dynamics and Propulsion 4 credits (3-0-2) Pre-requisites: MEL241 Revision of fundamentals. Thermodynamics of compressible flow wave motion in compressible medium, Mach number and cone, properties. Steady onedimensional compressible flow through variable area ducts. Converging and converging-diverging nozzles and diffusers. Effects of heating and friction in duct flow, Rayleigh and Fanno lines. Flows with normal shocks. Oblique shocks and reflection. Expansion waves. Prandt lmeyer flow. Flow over bodies. Measurements and applications. Jet propulsion types of engines, propulsion fundamentals. Compressor, combustor and turbines construction and performance. Rocket propulsion basics,

183 solid and liquid propelled engines, parametric studies, construction features, single and multi-stage rockets. Thrust chamber and nozzle models. Studies of in-use engines. Environmental aspects. MEP341 Thermal Laboratory 1.5 credits (0-0-3) Pre-requisites: MEL242 & MEL241 Experiments related to courses MEL242 Energy Conversion and MEL243 Heat and Mass Transfer courses. Application of uncertainty analyses. Experiments will be conducted in a group of two students. A professional report is to be prepared for each experiment. MEL342 Power Plant Technologies 4 credits (3-0-2) Pre-requisites: MEL241 & AML160 Introduction to power systems and technologies. Demand variation and forecasting. Grid features. Siting and costing. Diesel generators: systems, equipment and layout. Fossilfuelled steam power plants: Boiler and accessories. turbine and accessories, feed cycle equipment, generator. Combined cycle power plants: gas turbine, heat recovery boiler. Nuclear power: nuclear reactions, fuel, moderator and coolant, Neutron life cycle. Light water, Heavy water, Gas-cooled and fast reactors. Hydroelectric plants: Features and siting, Pelton, Francis, Kaplan and propeller turbines construction, mini- and micro-turbines. Renewable energy: solar, geothermal, wind, biomass, ocean, fuel cells, unique features of decentralized systems. Co-generation systems. Environmental issues, sustainability and future scenarios. MEL343 Fuels, Combustion and Pollution 4 credits (3-0-2) Pre-requisites: MEL241 Introduction. Fuels: gaseous, liquid and solid. Sources, method of procurement, transportation and end uses. National and international perspectives - economic and social aspects, and policies. Physical and chemical characterizations. Chemical thermodynamics and kinetics. Conservation equations for multi-component systems. Premixed systems: detonation and deflagration. Laminar flame problems and effects of different variables. Measurement of flame velocity. Flammability limits. Ignition and quenching. Turbulent premixed flames. Non-premixed systems: laminar diffusion flame jet, droplet burning. Combustion of solids: drying, devolatilization and char combustion. Coal combustion. Pollution: Main pollutants and their environmental impact. NOx, CO and SOx formation chemistry. Particulate pollutants. Emissions from engines, power plants and industrial applications. Low NOx burners and furnace design. MEL344 Refrigeration and Air-Conditioning 4 credits (3-1-0) Pre-requisites: MEL140 Revision of fundamentals. Applications. Environmental issues. Vapor compression system: Ideal and real cycle analyses, design and optimization. Refrigerants: designation, properties, environmental considerations. Advanced vapor compression cycles, part-load operation. Gas cycle refrigeration. Components: condensers, evaporators, compressors and expansion devices construction, operation and performance. Vapor absorption cycles: operation, system design, components. Psychrometry: definitions, heating, cooling, humidification and dehumidification processes, evaporative cooling systems. Environmental comfort specifications and standards. Cooling load estimation and use of standards. Air conditioning systems and apparatus, air flow ducts, air quality. Control and optimization of HVAC systems. MEL345 Internal Combustion Engines 4 credits (3-1-0) Pre-requisites: MEL140 Thermodynamics of fuel-air cycles, real cycles; Unburned and burned gas mixture charts; Ignition, normal and abnormal combustion in SI and CI engines; Conventional and alternative fuels for engines; Conventional and electronic fuel management systems for SI and CI engines; Design of combustion chamber for SI and CI engines; Engine emissions; Lubrication; Cooling; Supercharging and Turbocharging; Modern developments in IC engines. MEL346 Turbo-machinery 4 credits (3-0-2) Pre-requisites: MEL140 & AML160 Revision of fundamentals. Types of turbomachines and their applications. Dimensional analysis and performance parameters. Cascade theory: types of cascades, flow and geometric parameters, boundary layer development. Wind tunnels: types, designs, construction features and instrumentation. Axial flow turbines, axial flow compressors, propellers, centrifugal fans, blowers and compressors fluid flow, types of blading, velocity triangles, diffusers and nozzles, pressure change, multi-staging, stall, enthalpyentropy diagram, efficiency, acoustics, applications. Wind turbines types, analysis, site, atmospheric aspects. Solar plant turbines: principles, construction features and performance. Future trends. MEC410 Colloquium (ME) 3 credits (0-3-0) Pre-requisites: Registered for MET410 Introduction to planning, preparing and making presentations preparation of slides, time management, communication aspects, etc. Making a presentation on practical training with response sheet for testing audience. Reading an assigned project report, making a presentation with audience response sheet and a critique on writing style, completeness and editorial get-up. Performing patent searches on an allotted product and making a presentation using diagrams/figures only. Preparing posters on practical training and presenting these at a poster session. MEL410 Creativity in 4 credits (3-1-0) 183 P a g e

184 Nature of engineering problems and solutions. Optimal engineering solutions via analysis, decision Making, creativity and information technology. Study of search for existing solutions, modification of existing solutions and innovative or inventive solutions in history of technology. Discussion of creative practices like automated solution searches, check listing, brainstorming, analogy, empathy, inversion, morphological synthesis, inventors methods, stretching of constraint networks and problem identification. Automation strategies of creativity like those of genetic algorithms, computer aided idea searches. MET410 Practical Training (ME) Non credit Pre-requisites: at the end of 6th sem. Prior to training, students and faculty identify industries where training that will meet the course objectives, in particular, linkages to the core mechanical engineering curriculum. An evaluation and monitoring plan is drawn up. Students spend at least 50 working days in the industry and submit regular progress reports to training coordinator. Training activities comprise study and participation in various aspects of a manufacturing enterprise and impacts on humans/society and environment. Before returning, each student submits a comprehensive training report, report(s) on projects, posters, presentation, response sheet and self-assessment. Training in academic institutions, software industry, laboratories, and organizations with narrow specialization is not permitted. MED411 Major Project Part 1 (ME) 4 credits (0-0-8) Team formation for designing, manufacturing and operating a selected product, formulating project management procedures. Need identification, assessment of alternative designs, selection of design for development, defining design and performance specifications, and testing procedure. Detailed mechanical, thermal and manufacturing-related design of systems, assemblies, subassemblies and components culminating in engineering drawings and material specifications; preparing bill of materials and identification of standard components and bought-out parts. MEL411 Mechatronics 4 credits (3-0-2) Pre-requisites: MEL312 & (EEL101 / EEL102) Overlaps with: MEL433/MEL749/EEL482 Introduction to mechatronic systems and components. Principle of basic electronics. Microprocessors and their applications, integrated circuits, sensors, actuators, and other electrical/electronic hardware in mechatronic systems. Principles of electronic/system communication. Interfacing, DA and AD converters, software and hardware principles and tools to build mechatronic systems. Selection of mechatronic systems, namely, sensors like encoders and resolvers. Stepper and servomotors; Solenoid like actuators; Transmission elements like Ball screw; and Controllers. Analysis and synthesis of mechatronic systems with applications to robotics, CNC systems, and others. 184 P a g e MED412 Major Project Part 2 (ME) 16 credits (0-0-8) Pre-requisites: MED411 The same student team continues working as per work plan of Part-1. MED411, and facilitators. Using engineering drawings, the process sheets are developed based on available materials, machine tools and other fabrication facilities. Materials and standard components are procured and manufacturing is carried out. After inspection, parts are accepted. Assembly procedure is finalized and the machine is assembled. Acceptance tests are carried out vis-à-vis specifications from Part-1. Functioning product is displayed at an Open House. Professional quality documentation of all designs, data, drawings, and results, change history, overall assessment, etc. is mandatory, along with a final presentation. MEL412 Advanced Mechanical Design 4 credits (3-0-2) Pre-requisites: MEL311 Concepts of fatigue and creep design. Production considerations in design. Advanced concepts for design of spur, bevel, worm and other types of gear drives, bearings, rotating discs, pressure vessels, etc. Optimization in design and computer aided design methods. MEL413 Design of Mechanisms 4 credits (3-1-0) Pre-requisites: MEL211 Study of existing mechanisms used in industry, machine tools, vehicles, high speed machinery. Classification of mechanisms. Structural analysis and synthesis for conceptual design. Theory of path curvature and finitely movements. Kinematic and dynamic design. Spatial Mechanisms. Errors in mechanisms and machines. Coding, evaluation and dimensional synthesis of mechanisms. MEL414 Computer Aided Mechanical Design 4 credits (3-0-2) Pre-requisites: MEL311 Overlaps with: AML710 Introduction and overview. Need and scope of Computer Aided Machine Design. Role of Geometric Modeling and Finite Element Method (FEM). Introduction to computer graphics technology and overview of hardware available for use in CAD, Geometric transformations and Projections. Windowing and view-porting. Geometric modeling; Modeling of curves, cubics, splines, beziers and b-splines, Modeling of surfaces, Modeling of solids b-rep, CSG, octree, feature based modeling, Introduction to the Finite Element Method, principle of potential energy, 1D elements, Derivation of Stiffness and Mass matrices for a bar, a beam and a shaft, Comparison with Analytical results, Solution of static problems and case studies in stress analysis of mechanical components, FEA using 2D and 3D elements. Automatic meshing techniques, Interfacing with CAD software, Case studies using FEM for Design of simple element geometries. Introduction to

185 Dynamic analysis, Nonlinear problems and FEA for plastic materials. MEL415 Vibrations Design 4 credits (3-0-2) Pre-requisites: MEL312 Overview. Need of vibration engineering design for mechanical equipment. Theoretical and Experimental routes to dynamic design., Modelling and simulation to predict vibration behavior of mechanical systems and products. Techniques for vibration control including designing for reduced excitation, choice of materials and configurations, isolation,passive and active techniques etc Finite Element model updating. Vibration engineering design Using techniques of modal testing, Finite element model updating, system identification and structural dynamic modification. Integration of dynamic design in mechanical engineering design. Some case studies of actual systems like machine tools, pumps, compressors, turbines, transportation systems. etc. MEL416 Robotics 4 credits (3-1-0) Pre-requisites: MEL311 & (EEL101 / EEL102) Evolution of automatons, manipulators and autonomous systems. Forward and Inverse Kinematics. Velocity control, Jacobian control of abundant systems, singular value decompositions and null spaces. Interpolation in 3-D spaces, dual numbers, quaternions and screws. Dynamics of manipulators, EL and NE formulations. Parallel Manipulators. Basics of vision systems. Robotic AI Paradigms and Navigation. MEL417 Lubrication 4 credits (3-0-2) Pre-requisites: MEL311 Importance of lubrication, mechanisms and regimes of lubrication. Viscosity and its measurement. Bearing varieties and selection. Hydrodynamic lubrication-journal and Thrust Bearings. Lubricants. Bearing materials. Rolling Bearings. MEL418 Reliability & Maintenance Pre-requisites: MEL311 System concepts in RAM, Fundamentals of reliability, Failure distributions, Statistical analysis of failure data, Weibull analysis, Monte Carlo simulation, System reliability assessment. Reliability of repairable and nonrepairable systems. Point, mission and steady state availability. Availability assessment. Maintainability and its assessment. Design for reliability and maintainability, Practical applications of RAM to systems, products and processes. MEL420 Total Quality Management 4 credits (3-0-2) 185 P a g e Pre-requisites: Completion of Practical Training in any program (xxt4y0) Evolution of quality paradigms, Customer-orientation, Quality philosophies, TQM in manufacturing and services. Tools and improvement cycle (PDCA). Life cycle approach to quality costsprevention; Appraisal and Failure costs. Organizational, Communicational and Team requirements. Attitude, value sys-tem and behavioral patterns. Use of teams in process management. Group dynamics, Quality circles, high performance and self-directed teams, Empowerment. Seven QC tools and their applications, Quality Function Deployment. Statistical process Control, Process capability, Total Productive Maintenance, Importance of Standardization (National and international) Quality Systems, Quality Manuals, Quality Information Systems and documentation. Auditing. Basics of ISO-9000 and ISO 14000: Relevance and misconceptions, Six sigma philosophy Quality strategy and policy. Motivation and leadership theories. Continuous vs. breakthrough improvements. Management of change. Quality award models and role of self-assessment. Benchmarking. Impact on society-environment implications. Implementation barriers to TQM practices. MEL421 Production Management 4 credits (3-1-0) Pre-requisites: MET410 The generalized model of a production system. Financial evaluation of new product polices. Profit Volume Charts, Risk analysis, Product mix decisions, Location and layout analysis, Product, process and cellular layouts, Demand forecasting, Aggregate production planning, Materials planning, MRP and inventory management, scheduling in job and flow shops. MEL422 Project Management 4 credits (3-1-0) Pre-requisites: MET410 / MET420 The nature of projects, the project as a non-repetitive unit production system, the project as an agent of change. Project Identification considering objectives and SWOT analysis, Screening of Project Ideas, Technical, Market, Financial, Socio-economic and Ecological Appraisal of a project. Work break down structure and network development. Basic Scheduling, Critical Path and four kinds of floats. Scheduling under probabilistic durations, Time Cost tradeoffs, Project Monitoring with PERT/Cost, Organizational aspects, Computer packages and Project Completion. MEL425 Flexible Manufacturing Systems Pre-requisites: MET410 / MET420 Flexible Manufacturing Systems: Introduction, Definitions, Industrial Relevance, Need for FMS, Problems of conventional batch manufacturing systems, Role of Information Technology, Overview of Multi model and mixed model flexible lines, Understanding Flexibility, Types of Flexibility in FMS, Flexible and Dynamic Manufacturing Systems, IT facilitated flexibility, integration and

186 automation, Role of Integrated and automated material handling systems, Typical FMS operation, IT based Tools: Computer simulation and AI for FMS, Group technology, Decision Support Systems, Design, Planning, Scheduling and Control Issues in FMS, Real time control strategies, Various FMS configurations, Computer configurations, FMS as mini-cim, Benefits and Justification for FMS, Future challenges and research issues etc. MEL427 Manufacturing Economics and Analysis 4 credits (3-1-0) Pre-requisites: MET420 & MEL221 Basics of economic analysis, concepts of varous types of costs, Decision making: Investment in a new machine, Replacement of the existing machine, Makeor-buy, break-even point, Decision about the product mix, Justifying the investment in advanced manufacturing technology, Various economic measure: NPW, IRR, Payback period etc. Concept and various methods of depreciation, tax considerations, Stochasticity analysis. Multi-attribute decision-making framework, concept of utility. The traditional accounting system (standard costing) and contemporary costing systems such as Activity Based Costing (ABC), Target Costing, and Information system required for analysis. MEL431 CNC Machines and Programming 4 credits (3-0-2) Pre-requisites: MEL331 / MEL233 An overview of CNC machines - need, benefits and limitations, classification of CNC machines, Constructional features of CNC machines, CNC part programming - Preparatory and Miscellaneous codes, transformations, subroutines, canned cycles for CNC lathe and milling, CNC program verification tools, CNC program generation from CAD, CNC controller and motion control in CNC system, Applications of CNC and recent advances in CNC machines. MEL432 Microprocessor Applications in Manufacturing 4 credits (3-0-2) Pre-requisites: (MET410 / MET420) & (EEL101 / EEL102) Overlaps with: MEL411/EEL375/CSP413 Review of manufacturing and need and integration of microprocessor applications. Digital electronics review: number system, gates, flipflops, counters, registers, tristate concept, TTL and CMOS circuits, memories, opamps, comparators, etc. Microprocessors: Microprocessor architecture and computer systems, timing diagrams and machine cycles, interrupts, instruction set, memory and I/O interfacting, programming techniques, PPI, Timer/Counters, Serial Interfacing and communications, Interfacing to keyboards and displays, Standard busses. Microcontrollers and their applications architecture and instruction set. Microprocessor based measurement and control: D/A and A/D conversion, data acquisition systems, optical interrupters and couplers, incremental encoders, interfacing of motors and transducers, open loop and closed loop systems, PID control, motion control and robotics. Case studies of applications in process and discrete manufacturing. MEL433 Micro- and Nano-Manufacturing 4 credits (3-0-2) Pre-requisites: MEL120 An overview of micro and nano mechanical systems and their applications in Mechanical, MEMS Microfabrication methods, Silicon Micromachining methods, Laser Micromachining methods, Mechanical Micromachining techniques, Nanomanufacturing methods, CAD/CAM Tools for Micro- and Nanomanufactuirng processes. MEL434 Design for Manufacturing and Assembly 4 credits (3-0-2) Pre-requisites: MEL331 / MEL233 An overview of three stages of product design, generating and evaluating conceptual alternatives from manufacturability point of view, selection of materials and processes, Evaluating part configurations for manufacturability, Evaluating parametric designs for manufacturability, DFM analysis for various manufacturing processes, Product design for manual assembly, product design for high-speed automatic assembly and product design for robot assembly. MEL435 Geometric Modelling for Manufacturing 4 credits (3-0-2) Pre-requisites: MEP201 and EC 90 Geometric representation of curves, surfaces and solids, Machining of free-form surfaces from geometric models, geometric modeling for die/mold design, geometric model driven process simulation and process planning, use of geometric models in inspection of curved geometries and reverse engineering, realization of free-form solids by layered manufacturing, computational geometry for manufacturing and inspection. MEL436 Injection Molding and Mould Design 4 credits (2-0-4) Pre-requisites: MEL311 Nature of engineering plastics, visco-elasticity, design methods and grade selection Principles of Injection Molding, Injection molding machine and types, capacity and clamping tonnage, mold size, plasticating extruder concepts, molding properties and control parameters, molding cycle. Injection Molds for thermoplastics, cavity and core- integer and insert type, product consideration, material consideration, shrinkage, flow length, mold temperature, molding stresses, parting line, feeding system design - sprue, runner, gate, weld line strength, ejection system design, mold cooling systems, runnerless molding, gas assisted and thermosets molding. Exercises on CAD/ CAM of molds, mold flow analysis, molding of articles, process control and defect identification. MEL441 Modeling and Experiments in Heat Transfer 186 P a g e

187 4 credits (2-0-4) Pre-requisites: MEP341 & MEL242 Introduction Geometrical and physical models of heat transfer applications, comparison with experimental data, assumptions and their implications. Property data and its modeling. Mathematical models: algebraic, ordinary and partial differential equations, boundary and initial conditions, solution methodologies. Results: representation and interpretation, uncertainty and error bands. Heat transfer experiments: design, uncertainty analysis, selection of geometrical and physical parameters, engineering drawings, fabrication and instrumentation, rig calibration. Temperature, pressure and flow rate measurements. Systemic errors in temperature measurement: thermocouple and thermowell conduction, radiation and other phenomena. Data acquisition systems: basics and applications. Project-type work involving modeling, and designing and performing experiments related to heat transfer applications. MEL442 Thermal Analysis of Bio-systems 4 credits (3-0-2) Pre-requisites: MEL242 Introduction. Bio-fluid dynamics: Blood system network and physiology, blood rheology, Vessel structure and mechanical properties. Heart and pumping process. Blood flow in body tissues. applications dialysis, heart-lung machines. Lung and airways system network and physiology. Air and particle flow in airway passages, Alveolar dynamics. Eye, ear and nose system. Fluid mechanics of flight and swimming. Heat transfer: Body temperature and moisture regulation, heat balance and control system, applications to abnormal conditions. Bioheat equation, temperature distribution in tissue, applications to abnormal situations. Heat transfer in animals, fish, birds and insects. Thermodynamics of muscle. Micro-scale heat transfer and bio-systems. Properties of tissue. Laws, codes and regulations. Applications, plants, food processing, eco-systems. MEL674 Principles of Management Introduction to management. Theories of management : Traditional behavioural, contingency and systems approach. Organisation as a system. Interaction with external environment. Managerial decisionmaking and MIS. Planning approach to organisational analysis, design of organisation structure; job design and enrichment; job evaluation and merit rating. Motivation and productivity. Theories of motivation, leadership styles and managerial grid. Co-ordination, monitoring and control in organisations. Techniques of control. Japanese management techniques. Case studies MEL716 Micro/Nano Scale Heat Transfer 4 credits (3-0-2) Introduction to micro/nano scale transport phenomena, size effect behaviour, overview of Engg. applications, fundamentals of micro/nano scale fluid mechanics and heat transfer - kinetic theory, quantum mechanics considerations, Boltzmann transport equation, molecular 187 P a g e dynamics modelling, microfluidics, Knudsen number, slip theory, micro/ nano scale heat conduction thermal conductivity models, specific heat, thin films, convection in microtubes and channels, boiling and condensation, nanoparticles and nanofluids - preparation and transport properties, microscale radiative heat transfer - modelling, properties, measurements at microscale, Engg. applications- flow in microchannels, micro heat pipes, microelectronics, superconducting films, radiation etc. MEL732 Machine Tool Design 4 credits (3-0-2) Design requirements of machine tools. A design approach for machine tools. Identification and quantification of objectives and constraints in machine tool design. Estimation of power requirements and selection of motor for metal cutting machine tool spindles. Design of gearbox, spindle and guideways. Principles of design of structural components, namely, head stock, tail stock, carriage, table, knee, column and overarms to achieve desired static & fatigue strength, stiffness, dynamic characteristics and other requirements. Exercises on the design of machine tools using existing CAD software packages. Introduction to computer integrated manufacturing systems and CNC machine tools. Design/selection of linear motion systems, ball, screws, CNC feedback devices, controllers, feed drives and servomotors for CNC machine tools. Recent developments in CNC and other machine tools. MEL749 Mechatronic Product Design 4 credits (3-0-2) Introduction to mechatronic systems and components. Principles of basic electronics. Microprocessors and their applications, integrated circuits, sensors, actuators, and other electrical/electronic hardware in mechatronic systems. Principles of electronic/system communication. Interfacing. DA and AD converters, software and hardware principles and tools to build mechatronic systems. Design and selection of mechatronic elements namely sensors like encoders and resolvers; stepper and servomotors, ball screws, solenoid like actuators, and controllers with applications to CNC systems, robotics, consumer electronic products etc. Design of a mechatronic product using available software CAD packages. MEL751 Industrial and Systems 4 credits (3-0-2) Industrial.: Definition and Evolution, Understanding Industrial System Focus: Production/Service System. Performance measures of a Production System-Production, Productivity, Efficiency, Effectiveness, Quality, Flexibility, Agility etc.. Classical Industrial -Work Study: Method Study and Time Study, Human Factors, Ergonomics, Motivation Recent and Emerging Applications of IE -Role of IT in Systems MIS, FMS etc. ;Japanese Influences: Just in Time (JIT), Kanban etc.; Increasing Integration in Industrial Enterprises: From MRP to ERP to Supply Chain Management; Career Opportunities in Industrial.-Career Options, Types of Jobs and Employers, Entrepreneurship.Industrial Tool

188 Kit.-Technical skills: IE problem Solving and OR. ;Human skills Teamwork, Communication skills.; IT skills - Decision Support System (DSS), Intelligent Systems. Managers, System and Process (ERP) Specialists, Change Managers. MEL752 Quality Assurance 4 credits (3-0-2) Introduction to quality assurance and quality control, Various elements in Quality Assurance program, On-line and Off-line quality control, Statistical concepts in quality, probability distributions, Central limit theorem, Chance and assignable causes of quality variation, Process control charts for variables, Control chart parameters, Target process setting / Centering, Control limits and specification limits. Process capability studies, Capability indices, Quality remedial / Corrective actions, Special purpose control charts, Reject limits, Variables inspection and attributes Inspection, Control charts for attributes, Narrow limit gauging, Quality rating, Defects classification, Average run length, Sensitivity of control charts. Sampling inspection for product acceptance, Single, double, multiple & sequential sampling schemes, OC, AOQ, ASN, and ATI curves, Design of sampling plans, Standard sampling systems, Economics of product inspection, Quality costs, ISO 9000 quality system, Product quality and reliability, Failure data analysis and life testing. Problems and illustrations in Quality Assurance. MEL754 Operations Planning and Control 4 credits (3-0-2) Generalised model of a production system, the national economy as a Leontief s input- output system, decisions in the life cycle of a production system, evaluation of investments in new product and services, risk analysis using decision trees, product mix decisions, deterministic and stochastic models, different kinds of production systems, mass, batch job and cellular production, location decisions: multi-criteria approach, mathematical models for facility location and layout, use of iso-cost lines in location decisions, demand forecasting using qualitative and quantitative methods, aggregate production planning, hierarchical production planning, materials requirements planning versus conventional inventory control. MEL763 Methods and Ergonomics 3 credits (2-0-2) Introduction to work study & its techniques. Method Study, Motion study & Principles of Motion Economy, Work Measurement and its techniques of Time study. Production study. Work sampling, Standard Data systems, PMTS, Job Evaluation & Merit Rating and Wage Incentive payment systems. Introduction to Ergonomics & Man Machine systems. Basic Ergonomics and work physiology, Measurement of work, Applied Ergonomics & work Design & work place layout. MEL772 Metal Forming Technology Technological advances in metal forming processesforging, rolling, extrusion, wire drawing and sheet metal forming, Design of roll pass and rolling schedules, Description of typical cold rolling and hot rolling mill plants, Computer aided die design for forging, extrusion and wire drawing, Automation in metal forming processes, Recent developments in forming equipment (high speed presses etc.), Advances in sheet metal forming, Sheet metal die design, Formability evaluation, Unconventional forming processes like Hydrostatic extrusion, High energy rate forming processes, Hydro-forming of sheets and tubes, Powder forming, Finite Element Simulation of forming processes. MEL775 IT in Manufacturing Enterprises Production Systems, Manufacturing Enterprises as Systems, Appreciate the evolving manufacturing environment and multi-attributed competition: IT role Challenges and Opportunities, Evolving Role of Information Technology in Enterprises: P&I Implications, Technology Management Challenges, Technical Fundamentals: MIS in Manufacturing Enterprises, FMS (Flexible Manufacturing Systems), CIM Systems, Intelligent Manufacturing Systems, Concurrent and Extended Enterprises, ERP (Enterprise Resource Planning), E- Business and Supply Chain Management, Discrete Event Simulation and AI Applications in manufacturing enterprises, Implementation Issues, Future Trends, Careers etc. MEL778 Design and Metallurgy of Welded Joints 4 credits (3-0-2) Introduction to importance of welding in fabrication, Problems & difficulties in welded structures, How to obtain a sound welded structures and analysis, Properties for selection of materials, Characteristic properties and behaviour of commonly used materials, Effect of alloying materials, Heat flow in welds, Heating and cooling cycles in welding, Effect on HAZ, Hot cracking, Development of phases, Microstructure etc, Causes and cures for various discontinuities & defects in weldments, Weldability, Weldability of commonly used materials, Mechanical testing of weldments, Service and fabrication weldability tests and their importance, Thermal stresses and distortion, Brittle fracture and fatigue in welded joints, NDT of welds, Introduction to engineering physical metallurgy, Joining metallurgy and microstructures, Joint preparation weld symbols, Weld joint designs for strength and quality, Automation in welding, Cost analysis. MEL783 Automation in Manufacturing 4 credits (3-0-2) Modern developments in automation in manufacturing and its effect on global competitiveness, Need and implications of automation in Manufacturing, different types of production systems and automation, hard/fixed automation including process automation, Rapid prototyping and tooling. Hydraulic and pneumatic actuators, their design and control devices, sequence operation of hydraulic/pneumatic actuators, designing of complete 188 P a g e

189 systems with hydraulic, electro-hydrolic and digital control devices, applications in manufacturing, material handling systems, feeders, orienting and escapement devices, their analysis and design, Automatic assembly machines, designing for automatic assembly. of process of manufacture, Process-planning records, Production techniques for typical components and tools Jigs and fixture design and manufacture, Group technology & CAPP. MEL792 Injection Molding and Mold Design 3 credits (2-0-2) Nature of engineering plastics, visco-elasticity, design methods & grade selection Principles of Injection Molding, Injection molding machine and types, capacity & clamping tonnage, mold size, plasticating extruder concepts, molding properties and control parameters, molding cycle, Injection Molds for thermoplastics, cavity and core- integer & insert type, product consideration, material consideration, shrinkage, flow length, mold temperature, molding stresses, parting line, feeding system design - sprue, runner, gate, weld line strength, ejection system design, mold cooling systems, runnerless molding, gas assisted and thermosets molding. MEL794 CAD/CAM 4 credits (3-0-2) Introduction to CAD/CAM, representation of curves, surfaces and solids for CAD/CAM applications, computational geometry for manufacturing, product design for manufacture and assembly, computer aided process planning, computer aided assembly planning, computer aided inspection & reverse engineering, manufacturing process simulation, virtual & distributed manufacturing, computer integrated manufacturing. MEL796 Rapid Prototyping and Tooling 4 credits (3-0-2) Review of solid modeling techniques with comparison advantages and disadvantages. Basic Principal of RP processes, Classification of RP Processes, Various Industrial RP Systems like Sterolithography, Fused Deposition Modeling, Selective Laser Sintering, Laminated Object Manufacturing, 3D Printing, Ballistic particle modeling etc., Role of Rapid Prototyping and Rapid Tooling in Product Development and Simultaneous. Process planning for rapid prototyping, STL file generation Defects in STL files and repairing algorithms, Slicing and various slicing procedures, Accuracy issues in Rapid Prototyping, Strength of RP Parts, Surface roughness problem in Rapid Prototyping, Part deposition orientation and issues like accuracy, surface finish, build time, support structure, cost etc., Rapid tooling techniques such as laminated metallic tooling, direct metal laser sintering, vacuum casting. Introduction to reverse engineering Integration of reverse engineering and rapid prototyping. MEP790 Process 4 credits (2-0-4) Process engineering functions, Degrees of freedom and datum surfaces, Errors in manufacturing, factors affecting manufacturing accuracy, Preliminary analysis of processing alternatives, dimensional and tolerance analysis, Dimensional and Geometrical tolerances, detailed planning MEL769 Metal Forming Analysis 4 credits (3-0-2) Stress-strain relations in elastic and plastic deformations, Yield criteria for ductile metals, Work hardening and Anisotropy in yielding, Flow curves, Elements of theory of plasticity, Formulation of plastic deformation problems, Application of theory of plasticity for solving metal forming problems using slab method, Upper and lower bound methods, slip line field theory, extremium principles, Effect of temperature and strain rate in metal working, Friction and lubrication in cold and hot working, Technology and Analysis of important metal forming processes Forging, Rolling, Extrusion, Wire Drawing, Sheet metal forming processes like Deep drawing, Stretch forming, Bending, Introduction to Finite Element Analysis of metal forming processes. MEL780 Casting Technology 4 credits (3-0-2) Ferrous and Non-ferrous materials and their properties, Metal Matrix Composites and their properties and suitability as casting materials, Selection of materials for casting, melting of metals, Solidification of castings, casting design considerations, mould designs for sand and die castings, gating system design, riser design, casting defects: their causes and their removal, cleaning of castings, heat treatment of castings, inspection, repair and salvage of castings, quality control in foundries, special casting processes, Specific considerations to Grey Cl, steel and non-ferrous foundry practices, Foundry Mechanization Pollution control in Foundries. MEL781 Machining Processes and Analysis 4 credits (3-0-2) Survey of various methods of metal removal, Mechanics of orthogonal cutting, nature of contact between chip and tool, stress distribution at chip-tool interface, controlled contact tools, Mechanics of oblique cutting, Thermal aspects of metal cutting, Cutting fluids, method of selection of fluids, Dry cutting, Tool wear, Wear theories, experimental methods, Tool life, Machinability, machining economics, Dynamometry, Abrasive Machining Processes, mechanics of grinding process, grinding wheel wear, High Speed Machining, Ultra-precision Machining and hard turning, Non-Traditional Machining Processes such as EDM, ECM, USM, EBM, AJM, IBM, WJM and LBM. MEL784 CNC Technology and Programming 4 credits (3-0-2) Introduction to NC/CNC/DNC and its role in FMS and CIMS, Basics elements of CNC system, CNC Hardware Elements including drives, actuators & sensors, Construction of modern CNC machine tool controllers, 189 P a g e

190 Introduction to Part Programming, Radius and Length Compensation Schemes, Tooling & Work-holding for CNC machine tools, Advanced Programming Features & Canned Cycles, Geometric Modeling for NC machining & Machining of Free-form Surfaces, NC program generation from CAD models, NC Program verification and Virtual NC, Recent developments in CNC machine tools. MEL787 Welding and Allied Processes 4 credits (3-0-2) Introduction to joining technology, General survey and classification of welding processes, Safety and hazards in welding, Physics of the welding arc and arc characteristics, Metal transfer & its importance in arc welding, Various forces acting on a molten droplet and melting rates, Power sources for arc welding, Welding consumables: fluxes, gases and filler materials, SMAW, SAW, GTAW and related processes, GMAW and variants, PAW, Gas welding, Soldering, Brazing and diffusion bonding, Thermal cutting of metals, Surfacing and spraying of metals, Resistance welding processes: spot, seam, butt, flash, projection, percussion etc, Thermit welding, Electro-slag and electrogas welding, Solid-state and radiant energy welding processes such as EBW; LBW; USW, Explosive welding; Friction welding etc, Welding of plastics, Advances, challenges and bottlenecks in welding. MEL791 Composite Materials and Processing 4 credits (3-0-2) FRP Composites, fiber types, fiber forms and properties, matrices type and properties, lamina, laminate, composites macro and micromechanical analysis & properties, failure theories, primary and secondary manufacturing - Lay-up, Filament winding, Pultrusion, Compression moulding, RTM, RIM, SRIM, machining - drilling, routing etc., application Metal Matrix Composites powder metallurgy, sintering, squeeze casting, applications Ceramic Matrix Composites cl. 47 Department of Physics PHL 102 APPLIED PHYSICS 4 credits (3-0-2) Units and Dimensions, Elasticity, Properties of Liquids, Gravitation & Satellites, Sound Waves, Transfer of Heat, Electrostatics, D.C. Circuits, A.C. Circuits, Semiconductor Physics, Modern Physics, Nuclear Physics, Pollution and its control, PHP 100 PHYSICS LABORATORY 1.5 credits (0-0-3) List of Experiments: 1. To determine the dispersive power of a material of a prism with the help of a spectrometer. 2. To determine the wavelength of prominent lines of mercury using plane diffraction grating with the help of a spectrometer. 3. To determine the wavelength of Sodium light using the Michelson Interferometer 4. To study the charging and discharging of a capacitor and hence determine its time constant. 5. To determine the value of Planck s constant by means of a Light emitting diode. 6. To study the excitation of normal modes and frequency splitting measurements using the coupled oscillator. 7. To study the frequency of energy transfer as a function of coupling strength using coupled oscillator. 8. To determine the equivalent power loss resistance of an inductor. 9. To determine the impedance of L-R circuit and find phase relationship in current and voltage. 10. To study the relative phase difference between voltages across resistors and capacitors in series. PHL 110 FIELD& WAVES 4 credits (3-1-0) Interference of light, Diffraction, Quantum Mechanics and its application, Elements of material Science, Scalar and Vector Field, Gauss law and its application in electrostatics in vector form, Ampere s law, faraday s law of electromagnetic induction. Equation of continuity, Maxwell equations, wave equation, Plane wave solutions. 190 P a g e

191 191 P a g e Department of Mathematic

192 MAL-110 MATHEMATICS-I 4 credits (3-1-0) Differential Equations, Differential equation of first order and first degree, Differential equation of second and higher order with constant coefficients, Partial differentiation,, Euler s theorem on homogeneous functions, Total Diffrentiation Taylor s theorems, Maxima and Minima of two or more independent variable, Beta & Gamma Functions.Arc Length, Area and Volume Calculation of the curve, Rank and inverse of the matrix, consistency of linear system of equation, Eigen value, Eigen vector, Diagonalization of matrixes, Differential Calculus & Analysis, Asymptotes, Curve Tracing, Convergence of Sequence & Series. MAL-120 MATHEMATICS-II 4 credits (3-1-0) Vector calculus, arc length, directional derivative, gradient, curl, divergence, line and double integral, Green s theorem, surface integral, triple integral, Gauss and Stokes theorems with applications, Limit and derivative of a function, analytic function, Cauchy-Riemann equations, elementary functions, line integral, Cauchy s integral theorem, Cauchy s integral formula. : Derivatives of analytic function, power series, Taylor series, and Laurent series. Zeros and singularities, residues and residue theorem, evaluation of real integrals, Laplace Transforms, inverse Laplace transform, Convolution theorem, solving ordinary and partial differential equations, Fourier series, Fourier integrals and Fourier transforms. MAL101 BUSINESS MATHEMATICS 4 Credits (3-1-0) Introduction to Matrix, Inverse of Matrix, rank of matrix, solution to a system of equations, : Introduction to mathematical concepts in business, Fundamental Processes, fractions, decimals, percentage applications, discounts, markup interest Applications, Simple interest, compound interest.set Theory, Operating techniques, linear programming, Problem formulation, Graphical solution of an Lp problem, Elementary Transportation problem, elementary assignment problem traveling sales man problem. MAL 112 MATHEMATICAL FOUNDATION FOR COMPUTER SCIENCE 4 credits (3-1-0) Set & Functions, Matrices and Determinants, Limit, Continuity and Differentiability,Differential Calculus, Mean value theorems-roll s theorem, Lagrange s mean value theorem, Cauchy s mean value theorem, Taylor s theorem, Maclaurin s theorem (Statement only). : Integral Calculus, Indefinite integral, Definite integrals. Operators, Interpolation with equal, unequal and central differences,numerical differentiation, Integration & Solutions of Ordinary Differential Equations.Probability,Probability distribution functions. MAL 215 Mathematical Statistics For Management Decision 4 Credits (3-1-0) Introduction to Statistics, Measures of Central Tendency, Measures of Dispersion, Correlation and Regression, : Probability. MAL 104 APPLIED MATHEMATICS 4 credits (3-1-0) Introduction to Different Types of Expansion, Trigonometry, Matrices and Determinants, Numerical Integration, Two Dimensional Coordinate Geometry, : Conic, Function, Differential Calculus, Applications of Differential Calculus, Integral Calculus, Differential Equations, Vector Algebra. MAL-126 ALGEBRA AND DIFFERENTIAL EQUATIONS 4 credits (3-1-0) Algebra, Linear algebra, eigen values and eigen vectors, linear transformations, Sequence and series,convergent,divergent, absolute convergent, tests of convergent, Differential equation. MAL-230 NUMERICAL METHODS AND COMPUTATION 4 credits (3-1-0) Solution of system of linear equations,solution of non-linear equation in one variable, Interpolation and approximation,numerical differentiation and integration, Solution of ordinary differential equations. MAL-250 INTRODUCTION TO PROBABILITY THEORY AND STOCHASTIC PROCESSES 4 credits (3-1-0) Probability,Baye s rule,bernoulli trials, Random variables,discrete r.v., Probability distribution,binomial,poisson, Normal, Rectangular and exponential distributions, expectation values, moments,mgf s. Correlation and Regression,Queuing Theory. MAL-280 OPERATION RESEARCH 4 credits (3-1-0) Linear programming model formulation,linear programming problems,simplex method,duality,transportation problems,game theory, Queuing theory. MAL160 NUMERICAL AND STATISTICAL METHODS 4 credits (3-1-0) CSL105 DISCRETE MATHEMATICALSTRUCTURES 4 credits (3-1-0) 192 P a g e

193 Number Systems, Propositions and Logical Operations, Sets, Function, Relations, Recurrence Relations, Groups and applications, Graph theory. SML-202 BUSINESS STATISTICS 4 credits (3-1-0) Introduction to statistics, Dispersion and deviation, moments Karlpearson s Beta and Gamma coefficient, skewness and kurtosis, probability distribution, correlation and regression. MAL-225 STATISTICS FOR BCA 4 credits (3-1-0) Population, Sample And Data Condensation, Measures Of Central Tendency, Measures Of Dispersion, Permutations And Combinations, Sample Space, Events And Probability 48 Department of Chemistry Chemistry (CYL-110) 4 Credits (3-1-0) Unit 1: Phase Rule General Introduction, Definition of Phase, Component and Degrees of Freedom, one component system (Water and Sulphur), Two component system (Pb-Ag and Bi-Cd), Applications of Phase Rule. Unit 2: Water & its treatment Common impurities of water, hardness of water, determination of hardness by complexiometric (EDTA) method, numerical based on EDTA method, softening of water (Lime Soda, permutit (Zeolite) & Deionization methods). Numerical problems based on Lime Soda & Zeolite methods. Unit 3: New Material & Corrosion Fullerenes: Introduction, Properties, Preparation and uses. Organic Electronic Materials, Super Conductors, Optical Fibres, Corrosion: definition and significance, mechanisms of chemical or dry corrosion and electrochemical or wet corrosion, various protection methods. Unit 4: Thermodynamics Thermodynamics state, Application, Measurement of U and H: Calorimetry, Enthalpies for different types of reaction, Spontaneity, Gibbs energy change and Equilibrium. Unit 5: Chemical Dynamics Rate of Reaction, first order reaction, second order reaction, third order reaction, zero order reaction, determination of order of a reaction, half life methods, corllision theory-arrhenious equation, effect of temperature and pressure on a reaction, Molecularity, Homogeneous and Heterogeneous catalysis. References Books: Chemistry by Jain & Jain (Dhanpat Rai Publications). Physical Chemistry by Peter Atkins (Oxford Express) 193 P a g e APPLIED CHEMISTRY(CYL 102) 3 Credits (2-0-2) Constituents of the Atom, Bohr's Model of the Atom, Quantum Number and Electronic Energy Levels, Aufbau's Principle, Pauli's Exclusion Principle, Hund's Rule, n + l Rule, Electronic Configuration of Elements ( s,p,d Block Elements). Modern Periodic Law, Long form of Periodic Table, Study of Periodicity in Physical and Chemical Properties with, special reference to : - Atomic and Ionic Radii, Ionization Potential. Electron Affinity.Electronegativity.Variation of Effective Nuclear Charge in a Period. Metallic Character. Ionisation, Degree of Ionisation, Factors which Influence Degree of Ionisation, Hydrolysis Degree of Hydrolysis, Hydrolysis Constant, ph Value, Buffer Solution, Electrolysis, Faraday's Laws of Electrolysis. Postulates of kinetic Theory, Ideal Gas Equation, Pressure and Volume Corrections, Vender Walls Equations, Liquefaction of Gases, Critical Pressure and Critical Temperature for Liquefaction, Liquefaction of Gases by Joule Thomson Effect, Claude's Method and Linde's Method. Definition of Organic Chemistry. Difference between Organic and Inorganic Compounds, Classification and Nomenclature- Open Chain and Closed Chain Compounds, IUPAC System of Nomenclature. (Up to C5). General Principles and Terms listed in Metallurgy, Metallurgy of Iron and Steel, Different forms of Iron, Effect of Impurities on Iron and Steel, Effect of Alloying Elements in Steel. Water Pollution- Causes and Effects, Treatment of Industrial Water Discharges -Screening, Skimming and Sedimentation Tanks, Coagulation, Reductions, Chlorination, Biological Methods. Air Pollution- Causes and Effects, Control Methods Electrostatic Precipitator, Scrubbers, Gravitational Setting Methods, by Plants. Awareness on Green House Effect, Depletion of Ozone Layer and Acid rain. Sources of Water, Hardness of Water, Degree of Hardness, Estimation of Hardness by EDTA method, Problems on Calculation of Hardness, Disadvantages of Hardness, Softening Methods, Lime-Soda Method, Permutite Method, Ion -Exchange Method, Problems on Softening of Water, Drinking Water, its Requisites, Purification and Sterilization of Water. Definition, Classification, Calorific Value (HCV and LCV) and Numerical Problems on Calorific Value, Combustion of Fuels, Numerical Problems on Combustion, Solid Fuels, Coal and Coke, Liquid Fuels, Petroleum and its Distillation, Cracking, Octane and Cetane Values of Liquid Fuels, Synthetic Petrol, Power Alcohol, Bio-Gas, Nuclear Fuels Introduction to Fission and Fusion Reactions Definition, Theories ff Corrosion - Acid Theory (Rusting), Direct Chemical Corrosion or Dry Corrosion Wet Corrosion or Electro-Chemical Corrosion (Galvanic and Concentration Cell Corrosion), Various Methods for Protection from Corrosion Definition, Plastics, Classification, Constituents, Preparation, Properties and Uses of Polythene, Bakelite Terylene and Nylon, Rubber, Natural Rubber,

194 Vulcanisalion, Synthetic Rubbers - Buna - N, Buna-S, Butyl and Neoprene Manufacturing of Portland cement, Chemistry of Setting and Hardening of Cement, Glass: Preparation, Varieties and Uses. Definition, Classification, Properties of Lubricants: Viscosity, Oiliness, Flash Point, Fire Point, Acid Value, Saponificatin, Emulsification, Cloud and Pour Point, Artificial Lubricants. Refractories: Definition, Classification and Properties; Abrasives: Natural and Synthetic Abrasives; Paint and Varnish: Definition and Function of Constituents; Soap and Detergents: Definition, Properties and Uses. Superconductors, Organic Electronic Materials, Fullerences, Optical Fibers. population growth, variation among nations, population explosion, environment and human health, role of Information technology in environment and human health. ENVIRONMENTAL STUDIES SYLLABUS UNIT I: The Multidisciplinary Nature of Environmental Studies Definition, scope and Importance, Need for public awareness, types of natural resources, depletion of natural resources, conservation of natural resources, equitable use of natural resources, carrying capacity, green accounting UNIT II: Ecosystems Concept of an ecosystem, structure and function of an ecosystem, producers, consumers and decomposers, energy flow in the ecosystem, ecological succession, food chains, food webs and ecological pyramids, introduction, types, characteristic features, structure and function of the following ecosystem: (forest ecosystem, grassland ecosystem, desert ecosystem, aquatic ecosystems. UNIT III: Biodiversity and Conservation Biodiversity, endangered and endemic species of India, India as a mega-diversity Nation conservation of biodiversity: In-situ and Ex-situ Conservation of biodiversity, Man-wildlife Conflicts UNIT IV: Environmental Pollution Sources of Pollution, kinds of pollution, management of environmental pollution, solid waste management, role of an individual in prevention of pollution, pollution case studies disaster management UNIT V: Legal Aspects in Environmental Protection, Human Population and the Environment 194 P a g e Water (prevention and control of pollution) act, air (prevention and control of pollution) act, the environment (protection) act, forest conservation act, wildlife protection act, issues involved in enforcement of environmental legislation,

195 49 SYLLABUS ENGLISH (All Semester) I SEMESTER SUBJECT NAME: ENGLISH IN PRACTICE CODE: HUL credits (2-0-2) Communication, Types of communication, Group Communication, Writing Skills: Paragraph, Essay, Message, Letter and Application Writing, Comprehension review, Functional Grammar: Types of sentences, Tenses, Tag questions, Phrasal Verbs, Conjunction, Modals, Review the Literature: Poetry: Mending Wall by Robert Frost, Prose: Of studies by Francis Bacon, Novel: A Tale of two cities by Charles Dickens II SEMESTER SUBJECT NAME: COMMUNICATION SKILLS CODE: HUL credits (2-0-2) Letter Writing: Formal letters, various types of applications, job application, and difference between resume, Bio Data, CV and Resume Writing. Proposal Writing: Definition and purpose, types of proposals, characteristics, structure and body of proposal, style and appearance, evaluation of proposals. Personal Etiquettes: Self-introduction, table etiquettes and social behavior. Effective presentation strategies: MS-PowerPoint, Planning a Presentation, Outlining and structuring a presentation. Review the Literature: Development of Reading Skills: Poetry: The world is too much with us by William Wordsworth Prose: A Tryst with destiny by J.L.Nehru Novel: A Vision for 2020 by A.P.J. Abdul Kalam III SEMESTER SUBJECT NAME: TECHINICAL COMMUNICATION CODE: HUL credits (2-1-0) Business Letter Writing: Significance, purpose, layout, structure and principles of business letter writing, the 7 C s of business letter writing, types of business letter. Technical Communication: Scope and significance, forms of Technical Communication, difference between General writing and Technical Communication What is a report, types of report, objective of report. Public Speaking: Invention, arrangement, style, delivery, act of successful public speaking, dealing with the topic. Copy Writing: Notice Writing, advertisement drafting, invitation, poster making. Review the Literature Development of Reading Skills: Poetry: When you are Old by W.B.Yeats Prose: The Essentials of Education by Richard Livingstone Novel: The Guide by R.K.Narayan Interview Skills: Objective of Interviews, types of interview. Research Paper and Dissertation: Selection of topic, Introduction, structure of a thesis paper, research methodology. Corporate Etiquettes: Corporate behavior, table etiquettes. Book Review: Reading, description and evaluation of book. V SEMESTER SUBJECT NAME: SOFT SKILLS AND PERSONALITY DEVELOPMENT CODE: HUL credits (3-1-0) Personality Development and soft Skills: leadership qualities, interpersonal skills, time management, attitude, ethics, integrity, self-confidence, team management, problem solving. Decision Making Skills: Case Study. Job Interviews: Types of Interview, importance of body language in interview, mock interview. Group Communication: forms and use of body language, Do s and don ts in Group discussion, mock group discussion. Lateral, Creative and Innovative Thinking:Introduction, Need of Lateral thinking, Techniques of Lateral thinking, difference between perception and processing, case studies and problem solving. Review the Literature: Development of Reading Skills: Poetry: From the inspired poem If by Rudyard Kipling Prose: The Essentials of Education by Richard Livingstone Novel: A Room of One s Own by Virginia Woolf VI SEMESTER SUBJECT NAME: COMMUNICATION SKILLS AND PERSONALITY DEVELOPMENT CODE: HUL credits (2-1-2) Public Speaking: arrangement, style, delivery, impromptu, manuscript, extemporaneous. Writing Skills: Business Letter Writing, types of Business Letter, Resume Writing, cover letter, Resume Writing, writing. Career Planning: Self-Exploration, Self-Introduction, and corporate dressing. Job Selection Skills: Group Discussions, types of interview, mock interview, common interview questions. IV SEMESTER SUBJECT NAME: LANGUAGE AND COMMUNICATION CODE: HUL credits (3-1-0) 195 P a g e

196 50 Polytechnic Department of Civil DCE 202 Fluid Mechanics 3.5 Credits (2-1-1) Introduction: concepts- Fluids and solids, Liquid, gas and vapor; Fluid mechanics: Kinematics, Dynamics; Fluid properties,fluid Pressure and its Measurement-Definition and its units; Pascal's law: Intensity of pressure at a point in fluid at rest, Pressure head; Pressure: Atmospheric pressure, Gauge pressure, Vacuum pressure,hydrostatics - Total pressure; Centre of pressure; Total pressure and center of pressure in different cases, Hydrokinematics, Hydrodynamics and Measurement of Flow, Orifices and Notches, Flow through Pipes, Flow through Channels, Turbines, Pumps. DCE 203 Building Technology 3 Credits (2-1-0) Introduction-Definition of a building, Stone Masonry, Brick Masonry,Walls,Foundation,Scaffolding, Shoring and Underpinning,Dampness and its Prevention,Arches and Lintels,Doors,Windows,Stairs and Stair Cases,Roofs,Floors,Finishing of buildings, Building Bye Laws,Basic Principles of Building Planning, Orientation,Site Selection,Design of Buildings. DCE 204 Surveying I 3 Credits (2-0-2) Introduction-Plane surveying and geodetic surveying, Chain Surveying - Different types of chains, Traversing, Fixing and marking stations; Base line,plotting of traverse, Open traverse, Closed traverse; Booking in field, Compass Surveying - Adjustment of error in a closed traverse, Prismatic compass; Surveyor s compass, Local attraction; Correction of bearings due to local attractions; Leveling, Contouring,Plane Table Surveying,Minor Instrument - Study and uses of: Hand level, Abney level, Clinometer. DCE 205 Transportation 3.5 credit (2-1-1) Importance of highway transportation, Necessity of highway planning, Highway Geometric Design Scope of traffic engineering, Passenger car unit (PCU), Traffic control devices - signs, signals, marking, Highway Materials,Construction of Roads,Highway Maintenance,Road Drainage and Road Arboriculture, Bridges, Railways,Rails, Sleepers, Ballast, Fixture and Fastenings, Railway Geometries, Points and Crossing, Tracks Laying, Maintenance, Stations and Yards, Signaling, Tunneling. DCE 206 Soil and Foundation 3 Credits (2-0-2) Introduction and scope of soil engineering, Fundamental Definitions and Relationships,Classification of Soils, Permeability of Soils, Compaction, Consolidation, Shear strength, Bearing Capacity, Earth Pressures,Soil Exploration, Foundation, Pile Foundation, Soil Stabilization. DCE 207 Concrete Technology 3 Credits (2-0-2) Manufacture of Portland cement,classification of aggregates,water- Indian Standards for quality of water for use in cement concrete Admixtures and Construction Chemical-; Admixtures: Plasticizers, Super plasticizers, Retarders, Accelerators, Fresh Concrete, Concrete Operation,Strength of Concrete, Special Concrete, Formwork, Quality Control at Site, Concrete Mix Design, Deterioration and Restoration of Concrete. DCE 208 Building Drawing 1 Credit (0-0-2) Detailed working plan, elevation and section of the following-two bed room residential single story building with given direction (North, South etc.), Three bed room duplex bungalow with the given plot size, Detailed plan of above showing house drainage, water supply and electrical fittings as per BIS., Hostel building, Primary health centre, School building, Panchayat,Drawing of a small residential building from measurements,detailed working plan, elevation and section through stair-case drawing of a two storied building. DCE 209 Construction Materials and Equipments 3.5 Credits (2-1-1) Classification of rocks; Geological classification - igneous rocks, sedimentary rocks and metamorphic, Meaning and composition of brick; Preparation of brick clay, Tiles,Introduction - lime, calcination, quick lime, slaking, setting, hardening, hydraulicity; Classification of lime- Lime Mortar, Cement and Cement Mortar, Timber, Ferrous Material, Non Ferrous Metals, Glass, Classification of paints, Paints and Varnishes,Equipment for Earth Work and Compaction,Bitumen or Asphalt Mixing Plant,Hauling Equipment,Equipment for Concreting-Concrete batching and mixing plant. DME 202 Fluid Mechanics & Machines 3.5 Credits (2-1-1) Introduction: Fluid Pressure and its Measurement, Hydrostatics, Hydrokinematics, Hydrodynamics and Measurement of Flow, Energy of fluid - pressure, kinetic and potential; Bernoulli's theorem (no proof): Assumptions and its limitation, Conversion of pressure into pressure head, velocity into kinetic head; Applications of Bernoulli's theorem: Pitot-tube, Venturimeter, Orificemeter, Orifices, Flow through Pipes, Impact of Free Jet, Hydraulic Turbines, Centrifugal Pump, Reciprocating Pump, Miscellaneous Hydraulic Machine. DCE 301 Theory of Structure 3 Credits (2-1-0) Different types of frames,slope and Deflection-Calculation of slope and deflection in simply supported and cantilever beams, loaded with point,propped Cantilever Beam- Drawing of B.M.D. and S.F.D, Fixed Beams, Continuous Beams-Drawing of BMD and SFD for continuous beams,rolling Loads,Influence Line Diagram for the following in Simply Supported Beams,Three Hinged Arch,Retaining 196 P a g e

197 Walls-Types of retaining walls; Stability of retaining walls,indeterminate Structures. DCE 302 Design of Steel Structure 3 Credits (2-1-0) Structural Steel; Structural Steel Sections,Bolted Connections,Welded Connections-Advantages and Disadvantage of welded joint; Permissible stresses in welds; Types of welded,design of Tension Members,Compression Members,Effective length, slenderness ratio, radius of gyration,design of slab base; Design of gusseted base,design of Beams,Roof Trusses- Basic components of roof truss.; Types of loads on roof truss-: Dead load, Live load, Wind load,plate Girder. DCE 303 Design of R.C.C. Structure 3 Credits (2-1-0) Introduction-Reinforced Cement Concrete- its meaning, constituents, functions and specifications as per I.S, Single reinforced beam; Doubly reinforced beam; T-beam; Lintel; Cantilever beam,analysis and Design of Beams, Flexural Members-Limit state of collapse; Limit state of flexure; Neutral axis, moment of resistance,slabs,compression Members (axially loaded columns),design of Footing,Retaining Wall, Pre-stressed Concrete -Definition, advantages and methods of pre-stressing; Losses in prestressing; Stress calculations. DCE 304 Surveying II 3.5 Credits (2-0-3) Theodolite-Types; Different parts of a Vernier Transit Theodolite; Fundamental axes; Temporary, Traverse- Types - open and closed traverse, Tacheometry-Concept; Methods: Stadia methods, Tangential methods,trigonometrical Levelling-Determination of heights and distance of a point,curves-elements of simple circular curves; Designation of curve; Radius and degree of curve; Relation between radius and degree of curve,mine Surveying, Equipment of mine surveys, Modern Instruments - Brief Description, Electronic distance measuring instruments; T-2-Theodolite; Total station; Global Positioning system. DCE 305 Water Supply & Sanitary 3 Credits (2-0-2) Water Demand and Quantity-Water demand per capita for domestic and other uses, Examination of water: Physical, Chemical, Bacteriological, Flow diagrams of treatment plants; Function, constructional, Regulatory Valves,Distribution of Water,Rural Water Supply-Important aspects; Sources; Treatment, System of Sanitation, Quantity of Sewage, Characteristics and Composition of Sewage, Building Drainage, Inspection of mains; Cleaning of sewers,general composition of sewage,primary treatment; Secondary treatment; Function and construction of: Screening chambers, Introduction; Dry and wet latrines: selection, location, design life; Latrine for waterlogged high flood areas. 197 P a g e DCE 306 Irrigation 3 Credits (2-1-0) History of irrigation development in India, Water Requirements of Crops, Hydrology-Hydrologic cycle; Rainfall its characteristics and methods of measurement, Dams-Types of Dams; Selection of site for a dam, Earthen and Rock fill Dams, Homogeneous dams and composite dams, Spillways, River Training Works, Canals, Explanation of terms-canal, Well Irrigation, Diversion Head Works, Water Logging-Definition; Causes, effects and preventive measures, Cross Drainage Works. DCE 307 Civil Estimating and Costing 2.5 Credits (1-0-3) Introduction-Purpose; Importance of estimating, Specifications-Importance of specifications, Principles for writing out specifications, types of specification; Writing general and detailed specifications for items of work in building construction,rate-analysis-factors affecting cost of work; Explanation of terms; Prime cost; Original cost; Provisional items; Detailed Estimates for Buildings- Calculation of quantities; Preparing abstract of cost for a residential building. DCE 308 Environmental 2 Credits (1-1-0) Environment and Ecology- Definition and understanding of their concept; Ecosystem,Fresh water: Causes of water pollution in surface, Air Pollution-Definition; Sources; Harmful effects on living and non living beings; Permissible limits as per Indian standard; Remedial measures, Factors Affecting Environmental Pollution,Noise Pollution, Land Pollution, Environmental Impact Assessment (EIA)- Introduction; E.I.A. of thermal power plants, mining and nuclear radiation,global Environmental Issues Deforestation; Land sliding; Recharging and drying of water resources; Green house effects; Non Conventional Sources of Energy in Environmental Protection,Environment Laws,Pollution Control Acts. DCE 309 Construction Management and Accounts 2 Credits (1-1-0) Introduction-Different types of construction; Stages in construction from conception to realization; Construction team - owners, engineer and contractor,construction Planning -Construction project planning; Stages in planning; Bar charts; Introduction to Network Organization - Types of organization, Construction Contracts - Introduction; Proposal and agreements,construction Labour, Condition of construction workers in India,Inspection and Quality Control -Technical services required for inspection; Quality construction; Quality control operation; Quality control in concreting,construction Safety,Public Works Accounts. DCE 310 Earthquake Resistant Structures 2 Credits (1-1-0)

198 Seismology-Introduction; Causes of Earthquakes; Seismology: Seismic Waves, Seismograph, SeismogramStructural Dynamics -Loads; Effect of Earthquake motion on structures; Fundamental natural period, Behavior of Buildings during Earthquakes, Provisions for Seismic Strengthening of Masonry Constructions, Seismic Performance of Reinforced Concrete Buildings, Ductile Detailing of Reinforced Concrete Buildings, Disaster Management-Introduction; Disaster management; Disaster rescue; Psychology of rescue; Rescue workers. 198 P a g e

199 51 Polytechnic Department of Computer Science CSL 104 Computer & Information Technology Fundamentals 3 credits (2-0-2) Introduction to Computer System, Windows XP, Information Concepts and Processing, Computer Communication, Internet, Information Processing, Data Tools and Powerpoint. It includes basic practicals like studying computer components, getting familiar with windows booting, control panel utility, CD/DVD writing, Practice of Network Places, File Systems (NTFS), Practice of Paint, creating account, visiting of Internet websites. DCS 201 Programming and problem solving through C 3 credits (2-0-2) Introduction, Elements of C( Components used in C language), Console Input/output, Control flow (Statements used to control the flow), Arrays, Functions, Pointers, Structure & Enumerated Data Types, File Handling, Numerical Methods. Programs based on arithmetic operations, programs based on functions, Using arrays in C language and various constructs like structures, pointers. Programs using loops. DCS 202 Computers System Architecture 3 credits (2-1-0) Overview of computer Organization (Evolution of computer, Von Neumann architecture, Computer generations), Register & Micro operations, Basic computer organization, Central processor organization (Processor Bus organization, ALU: Simple and floating point, Stack Organization), Arithmetic processor organization, I/O organization (Peripheral devices, I/O processors, DMA, Interrupt handling, Data communication, Multiprocessor organizations), Memory organization, Introduction to parallel processing. DCS 203 Operating System Principles 2 credits (2-0-0) Introduction (What is an operating System, Mainframe, Desktop & Multi processor, Distributed System), Process management & CPU scheduling, Deadlocks (What is Deadlock?, Necessary Conditions for deadlock, Resource allocation graph, Deadlock prevention, Deadlock avoidance Banker s Algo, Deadlock Detection), Memory Management, Virtual memory (Concept of Virtual memory, Concept of Demand Paging, Page replacement Algorithms: FIFO, Optimal, LRU, Allocation Algorithms), File system, Distributed Operating System. DCS 206 Data Communication 2 credits (2-0-0) Introduction (Data Communication: Model and Components, Computer Networks, Line Configurations, Topology, Transmission modes, Communication Protocol: Layered Architecture, Reference Models: OSI and TCP/IP), Signals & Transmission (Analog and Digital Forms, Analog 199 P a g e Signals: Amplitude, Period and Frequency, Phase, Spectrum and bandwidth, Digital Signals), Multiplexing & Computer Hardware, Data Link Layer, Switching & Frame Relay. DCS 207 Database Management System 3 credits (2-1-0) overview (Need for DBMS, Components of DBMS, Applications of DBMS, Advantage of DBMS, Database system versus file system, Disadvantages of DBMS, Database System Concepts and Architecture; Application Architecture of DBMS), Data modeling using ER model (E- R Model concepts; Notations of E-R Diagram; Mapping Constraints: One-to-one, One-to-Many, Many-to-One, Many-to-many; Keys), Relational Data model & language, Normalization, Transaction processing concepts, deadlock handling, Concurrent processing techniques. DCS 208 Microprocessor and Interfacing 3 credits (2-0-2) Introduction (Microprocessor concept, Historical review of microprocessor development, Organization of a micro computer), 8085 architecture (Internal block diagram, 8085 signals and their functions), 8085 instructions & programming (Instruction format: Mnemonics, Opcode and operand, Instruction length; Classification of instruction: Data transfer, Arithmetic, Logical, Branching, Machine control), memory & i/o system, Instruction Execution & Timings, Interfacing with 8085, Introduction to X86 family. DCS 209 Internet and Web Technologies 3 credits (2-0-2) Internet basics (Concept, Establishing Connectivity on Internet, POP, SMTP, WWW, File Transfer, Telnet, IP Address, Brief overview of TCP/IP), HTML (File Creation, Web Server, Web Client; Introduction to HTML: HTML Tags, Structure of HTML Programs, Heading, Titles and Footers, Text Formatting), Javascript, DHTML (Cascading Style sheets (CSS): Font Attributes, Color, Background, Text and Border, List Attributes; Class: The <SPAN> </SPAN> Tag), CGI, Perl. DCS 210 PC Maintenance and Trouble Shooting 3 credits (2-0-2) Computer Installation (Site Preparation: Air-Conditioning Requirements, False-Ceiling and False-flooring, Fire- Protection system, Electrical Earthling; Power Supply Requirements), Safety & Security measures (Safety from Natural calamities, Theft and Fire Hazards; Data Security, Security from unauthorized users, Virus Protection Techniques, Firewalls, Folder Locking), working principle of peripheral devices, display technology- thin devices, optical storage devices, i/o ports, Hard disk drive, Windows components & tools, Memory. DEE 208 Microprocessor & C Programming 2.5 credits (2-0-1) Introduction (Evolution of microprocessor; Digital computer, Organisation of computer; Definition of: Instruction,

200 Program, Machine language, Assembly language, High level language; Compiler and Assembler), Microprocessor architecture (Functional block diagram; Pin-Out diagram with description; Buses: Address bus, Data bus, Control bus), programming & application of Microprocessor, Introduction to C Programming, Elements of C, Console i/o, Control flow, functions, Arrays, Pointers, Structure & Enumerated Data types. DME 210 C Programming 3 credits (2-0-2) Introduction to C Programming (Scope of C Language; Distinction and similarities with other HLLs; Special features and Application areas), Elements of C, Console i/o (Character set, Key words, Data types, Constants and Variables, Operators: unary, binary, ternary, Operator precedence), Control flow (Statements and blocks, if, switch, Loops: for, while, do-while, goto and labels, break, continue, exit, Nesting control statements), functions, Arrays, Pointers, Structure & Enumerated Data types. DEL 207 Microprocessor 3 credits (2-0-2) Number System (Decimal, binary, octal and hexa-decimal number system, Conversion of a number from one system to another system), Introduction to Microprocessor (Microprocessor concept; Historical review of microprocessor development; Organization of a micro computer), 8085 Architecture (Internal block diagram; 8085 signals and their functions), 8085 Instructions & Programming, Memory & I/O Systems, Instruction Execution & Timings, Limitations of 8 bit microprocessor. DEL 210 C Programming 2.5 credits (2-0-1) Introduction to C Programming (Scope of C Language, Distinction and similarities with other HLLs, Special features and Application areas), Elements of C (Character set Key words, Data types, Constants and Variables, Operators: unary, binary, ternary, Operator precedence), Console i/o (Types of I-O, Console I-O, Unformatted console I-O: getchar(),putchar(), gets(), puts(), getch(), getche(), Formatted I-O: scanf(), printf()), Control flow, functions, Arrays, Pointers, Structure & Enumerated Data types. DCS 301 Data Structures & Algorithm 3 credits (2-0-2) Introduction to Data Structures and Algorithms, Algorithm on Linked List, Algorithms on Stack, Algorithms on Queue, Non-Linear Data Structure: Tree, Non-Linear Data Structure: Graph,Programs based on linked list, Programs based on stacks and queue, Programs based on tree traversal, Programs based on Graphs, Programs based on sorting, Programs based on searching. DCS 302 Object Oriented Programming through C++ 3 credits (2-0-2) An Overview of Object Oriented Programming, Object Oriented Programming Using C++, Objects and Classes, Overloading of Functions and Operators, Inheritance and Polymorphism,Templates and Exception Handling, Managing Console I/O and File I/OPractice for Classes and Object Creation, Practice for constructors and deconstructor s creation, Practice for static and friend functions for a class,practice for Function overloading, Practice for Operator overloading, Practice for Copy constructor, Practice for inheritance,practice for virtual function, Practice for exception handling template,practice for read( ) and write( ). DCS 303 Unix Shell Programming & Administration 3 credits (2-0-2) UNIX an Introduction (Unix Architecture; Features of UNIX; Command structure and usage), File System (Basics of file; Structure of file systems; File permission; File ownership; Inodes; Partition),UNIX Commands (File management commands: ls, cat, rm, mv, cp, chmod,cmp,diff, comm.; Directory management commands),vi Editor (Three modes; Input mode, Adding and replacing text; Saving text and quitting The ex mode; The repeat factor), UNIX Shell, Shell Programming, Essential System Administration. DCS 304 Software 2 credits (2-0-0) Introduction (Software evolution and impact; Software Crisis; Program and Software Products; Software Characteristics; Software metrics; Emergence of Software ), Software Life Cycle Models (Why use life cycle models?; Waterfall model; Prototyping Model; Evolutionary Model; Spiral Model; Comparison of different Life Cycle Model), Requirement Analysis and Specification (Requirement Gathering Methods and Analysis; Feasibility Study; Software Requirement Specification (SRS): Contents of SRS document), Software Design, Function Oriented Design, Software Testing, Software Reliability and Quality Management. DCS 305 Dot Net Technology 3 credit (2-0-2) Introduction to NET Framework and Development Environment, Visual Basic.NET, Programming Concepts of VB.NET, Object Oriented Features of VB.NET, Windows FORMS and Controls, Database Connectivity using ADO.NET, ASP.NET,PRACTICALS: Practice programs on VB.NET using variables and operators, Practice programs on VB.NET using conditional and control structures, Practice programs on VB.NET using Arrays, Practice programs on VB.NET using Inheritance property, Practice programs on VB.NET using Forms and Controls, Practice programs on Database connectivity using ADO.NET, Practice programs on Data Access through ASP.NE, Practice programs on ASP.NET using web controls, Practice programs on ASP.NET using Event-handling, Practice programs on ASP.NET using Cookies. DCS 306 Computer Network 200 P a g e

201 2 credit (2-0-0) Data Link Layer and Local Area Networks (Data Link Layer Design Issues: Framing, Error Detection and Correcting Code, Error Control; LAN Protocols), Network Layer and Routing (Network Layer Design Issues; Routing Algorithms: Shortest Path Routing, Flooding, Distance Vector Routing, Hierarchical Routing, Multicast Routing; Internet Protocol), Transport Layer (Transport Layer Services; Transport Protocol Mechanisms: Addressing, Multiplexing, Establishment a Connection, Releasing a Connection, Reliable Delivery, Flow Control and Buffering), Application Layer, Wireless Networking. DCS 307 Data Warehouse & Mining 3 credits (2-1-0) Data Mining (Introduction to Data Mining; How Data Mining Works; Data Mining Tasks; Data Mining Elements; Data Mining Architecture; Advantages; Disadvantages), Data Pre-Processing (Task of Data Pre-processing; Data Cleaning; Data Integration; Transformation; Data Reduction), Data Mining Techniques (Decision Tree; Clustering; Genetic Algorithms; Artificial Neural Networks), Data Warehouse, Data Warehouse Architecture, Components of Data Warehouse, On-Line Analytical Processing. DCS 310 PHP & My Sql 3 credits (2-0-2) Overview of PHP (Static versus Dynamic Websites; Dynamic Contents from Databases; Developing Dynamic Internet Applications; Client-Side scripting versus Server- Side Scripting; Advantages and Capabilities of PHP; PHP versus ASP), Basic Scripting Loop and Conditional Constructs (PHP Scripting Fundamentals; Primitive Data Types; Defining Constants and Variables; Loop constructs: While, Do-While, For, Exit & Break), Arrays in PHP (Usage of Arrays in PHP; Initializing Arrays; Adding and Removing Items from Arrays; One-dimensional and Multidimensional arrays; Array Functions), Working with Databases and Forms, Using Cookies with PHP, MySQL. DCS 308 Introduction to Computer Security & Cryptography 2 credit (2-0-0) Computer Security (Introduction; Need of Security; Security approaches; Principle of Security), Attacks on Computer (Attacks: A general and technical view; Active and passive attacks; Program that attacks: Virus, Worm, Trojan horse, Applets, ActiveX controls, Cookies, Scripts; Preventing Virus; Specific attacks: Sniffing and Spoofing, Phishing, Pharming or DNS spoofing), Cryptographic: Concepts and Techniques, Symmetric and Asymmetric Key Cryptography, Internet Security Protocols, Securities, Firewall. DCS 309 Java Tools 3 credits (2-0-2) Java Fundamentals (Features of Java; Types of Java programs; Application programs; Applets; Sevlets; Java architecture; JDK tools), Applet (Applet life cycle; Applet tag; Paint( ), Update( ), Repaint( ), SetBackground( ), SetForeground( ), ShowStatus ( ); Different between applet and application programs), Graphics (Drawing lines, Arc; Drawing rectangles, oval; Drawing ploggon, Polyline; Clipping), AWT and Event Handling, Swing, JDBC, Servlet. PRACTICALS: Practice programs on applets, Practice programs on graphics, Practice programs on awt and event handling, Practice programs on swing, Practice programs on servlets, Practice programs on JDBC. 201 P a g e

202 202 P a g e

203 52 Department Computer Applications CSL 103 Introductions to Programming Using C & Lab 6 credits (3-1-4) Overlaps with: CSL 120 Introduction to Computers, Introduction to Programming, Introduction & the C character set, C Instructions, Control Structures, Arrays, Strings, Functions, Storage classes in C, Pointers, Structures and Unions, Files, C pre-processor CSL 716 Discrete Mathematical Structures 4 credits (3-1-0) Number Systems, Propositions and Logical Operations, Sets, Function, Relations, Recurrence Relations, Groups and applications, Graph theory. CSL 106 Pc Packages & Pc Software Lab 6 credits (3-1-4) Office Packages, Office activities and their software requirement,, Working with MS Word, Working with Styles, Advanced Features of MS-Word, MS Excel, MS PowerPoint, Outlook express CSL 107 Fundamentals of Computers & Information Technology 4 credits (3-1-0) Introduction to Number system and Codes, Boolean algebra and Gate networks, Combinational Logic, Flip-Flops, Registers and Counters, Memory and Introduction to Microprocessor CSL 120 Programming in C 4 credits (3-1-0) Overlaps with: CSL 103 Introduction to Computers, Introduction to Programming, Introduction & the C character set, C Instructions, Control Structures, Arrays, Strings, Functions, Storage classes in C, Pointers, Structures and Unions, Files, C pre-processor CSP 120 C Language Lab 2 credits (0-0-4) Pre-requisites: CSL 103/CSL 120 Lab is meant for developing programming skills in the students. Students have to develop and execute the programs related with the topics covered. CSL 281 Management Information System 4 credits (3-1-0) Overlaps with: CSL 241 Foundation of Information Systems in Business, An Overview of Management Information Systems, Business Applications of Information Technology, Managing Information Technology, Advanced Concepts in Information Systems CSL 761 Computer Organizations and Architecture 4 credits (3-1-0) Pre-requisites: CSL 107 Digital Logic, The Computer System, Central Processing Unit, Instruction set, CPU structure and Function, Microprocessor organizations, Parallel Organization, Control Unit CSL-271 Database Management Systems 4 credits (3-1-0) Overlaps with: CSL 305 Introduction to database systems, Elements of Database System, E-R Modeling, Relational Data Model, SQL, Data Normalization, File and system structure, Concurrency Control CSL-272 Operating Systems 4 credits (3-1-0) Overlaps with: CSL 373 Introduction to the Operating System, Types of OS, Process Management, CPU Scheduling, Deadlock, Memory Management, Virtual Memory, Information Management, File Concept CSL-273 System Analysis and Design 4 credits (3-1-0) Introduction, System Definition and concepts, System Development Cycle, System Planning, Prototyping, Business Process Re-engineering, Modular and Structured Design, System Design and Modeling, Input/output and Interface Design, System Implementation and Maintenance CSL-274 Object Oriented Programming Using C++ 6 credits (3-1-2) Pre-requisites: CSL 103/CSL 120, Overlaps with: CSL 760 Introduction, Introducing Object-Oriented Approach, Relating to other paradigms, Classes and Objects, Friend Function, Inheritance, Virtual Base Class, Polymorphism, Function Overloading, Operator overloading, File Handling. CSD-281 Minor Project in Visual Basic 2 credits (0-0-4) Students will develop a real time project by using Visual Basic as front end and Ms-Access or Oracle as back end. They will submit the project in soft copy as well as in hard copy. CSL375 Operating System 203 P a g e

204 Credits (3-0-3) Overlaps with: CSL 272 Introduction to Operating System, layered architecture/logical structure of operating system, Type of OS Process management- Process model, Process scheduling, Interprocess communication, Deadlock, Deadlock detection, recovery from deadlock, Memory management, Virtual Memory, Memory fragmentation, Demand paging, Thrashing, page replacement algorithms, File System, overview of file system in Linux & windows, Input/Output subsystems, Disk scheduling algorithm CSL-548 Net Programming using VB.net 6 credits (4-0-4) Pre-requisites: CSL 231Overlaps with: CSL 582 NET Framework, Common Language Runtime, Application installation & Assemblies, VB.NET IDE, Variables, Constants, Strings, An Introduction to Functions and Subs, Create Properties in your Classes, Error Handling, Working with different tools, menus, ADO.NET, ASP.NET, Working with Text Files CSL-705 Theory of computation 4 credits (3-1-0) Fundamentals, Strings, Alphabet, Language, Operations, Chomsky hierarchy of languages, finite automaton, Finite Automata NFA with Î transitions, Equivalence between NFA with and without Î transitions, Regular Languages, Grammar Formalism Regular grammars, Context Free Grammars, Ambiguity in context free grammars, Push Down Automata, Equivalence of CFL and PDA, Turing Machine (TM), TM Definition, Enumerable Languages CSL-740 Software 4 credits (3-1-0) Overlaps with: CSL 436 Introduction to software engineering, Importance of software, Software Requirement Specification, Analysis Principles, Water Fall Model, The Incremental Model, Prototyping, Spiral Model, Role of management in software development, Software-Design, Coding, Testing, Testing principles, Levels of testing, Software Project Management, Software Reliability & Quality Assurance, CASE (Computer Aided Software ) CSL-752 Principles of Compiler Design 4 credits (3-1-0) Basics Of Compiler And Lexical Analysis, interpreter, assembler and compiler, types of Compiler, Analysis of the Source Program, The Phases of a Compiler, Syntax Analysis: The Role of the Parser, Syntax-Directed Translation, Dynamic Memory Allocation & Memory Management, Storage-Allocation Strategies, Dynamic Storage Allocation Techniques, Code Optimization And Code Generation: Intermediate Languages 4 credits (3-1-0) Pre-requisites: CSL 103/CSL 120, Overlaps with: CSL 274 Features of OOP s, Comparison of C and C++. Object Modeling, Dynamic Modeling, C++ Programming Basics, Object & Classes, Arrays and String, Operator Overloading, Inheritance, Pointers, Virtual Function Streams and Files, Templates and Exceptions CSL-770 E-Commerce 4 credits (4-0-0) Introduction, Electronic Commerce - Technology and Prospects, Network Infrastructure for E- Commerce, Mobile Commerce, Wireless Application Protocol, Web Security, Importance of Firewall, Security Threats, Firewall design, Encryption, EDI Application in business, Electronic Payments, Payment Gateway, Certificates, Online Banking, Digital Signatures, Virtual Private Network CSL-782 Computer Graphics and Multimedia Programming 4 credits (3-1-0) Graphics Primitives, Display Devices, Aliasing and antialiasing in Raster technology, Input Devices, Input Techniques, Positioning techniques, Rubber-Band techniques, Dragging, Dimensioning technique, Mathematics for Computer Graphics, Point representation, Vector representation, Line Drawing Algorithms, Circle generating algorithms, polynomial algorithm, trigonometric algorithm, ellipse generating, Segment & Display files, Graphics Operations, Filling, Conics, Curves and Surfaces, Transformation, 3 D Graphics, Multimedia Terms, Animation: Introduction to Animation, Principles of Animation, Gif Animator CSL-449 Software Quality Management 4 credits (3-1-0) Pre-requisites: CSL 740/CSL 436 Overlaps with: CSL 786 Introduction, Software Quality, Role of testing, Unit Testing, Defect Prevention, Data Flow Testing, Data Flow Testing Criteria, Comparison of Data Flow Test Selection Criteria, Functional Testing, System Integration Testing, Different Types of Interfaces and Interface Errors, Documentation Tests, Software Quality, ISO 9126 Quality Characteristics, ISO 9000:2000 Software Quality Standard ISO 9000:2000 Fundamentals, ISO 9001:2000 Requirements. CSL-759 Cryptography and Network Security 4 credits (3-1-0) Network Security, Attacks, Services & Mechanisms, Encryption Schemes, DES, Triples DES, Public-Key Cryptography, RAS, Message Authentication & Hash Functions, Digital Signatures, IP Security: Electronic Mail Security; Pretty Good Privacy (PGP), Web Security, System Security CSL-760 Object Oriented Programming Analysis and Design 204 P a g e

205 CSL-545 Enterprise Resource Planning 4 credits (3-1-0) ERP Introduction, Benefits, Conceptual Model of ERP, Business Process Reengineering, Data ware Housing, Data Mining, ERP Marketplace and Marketplace Dynamics, The Changing ERP Market, ERP- Functional Modules, ERP Implementation Basics, ERP Implementation Life Cycle, ERP & E-Commerce, Critical success and failure factors, Using ERP tool CSL-546 Information Security and Cyber Laws 4 credits (3-1-0) Introduction, History of Information Systems and its Importance, Information System Threats and attacks, Security in Mobile and Wireless Computing, Security Concepts in Internet, Basic Principles of Information Security, Security Threats to Ecommerce, Concepts in Electronics payment systems, E Cash, Credit/Debit Cards, Physical Security: Needs, Disaster and Controls, Legal Challenges Framework for Information Security, ISO 27001, Model of Cryptographic Systems, Requirement of Digital Signature System, Intrusion Detection, Use of Tunneling with VPN, Security Concerns in VPN, Laws, Investigation and Ethics: Cyber Crime, Overview of Indian IT Act, Issues in ethical hacking. CSL 221 Data Structures Using C 6 Credits (3-1-2) Prerequisite: CSL 103/CSL 120 Overlaps with: CSL 630 Introduction, Basic Terminology, Arrays, Array Definition, Representation and Analysis, Stacks, Array Representation and Implementation of stack, Queues, Array and linked representation and implementation of queues, Linked list, Sorting: Bubble Sort, Selection Sort Insertion Sort, Quick Sort, Merge Sort, and Heap Sort, Searching, Sequential search, Binary search, Trees: Basic terminology, Binary Trees, Representation of Binary trees CSL 231 Visual Basic Programming And Lab 6 Credits (3-1-4) Client Server Basics: Discover Client-Server and Other Computing Architectures, Visual Basic Building Blocks and Default Controls: Forms, Using Controls, VB Advance Controls, Creating MDI, Working with Menus, VB Programming Fundamentals and Variables, Working With Math Operations, Strings, Formatting Functions, Controlling And Managing Program, Visual Basic and databases, Remote And ActiveX data Objects, ActiveX Controls, Extending ActiveX Controls And Classes, Client-Server Development Tools: COM, VB and Internal, Introduction to VBScript, Introduction to Active Server Pages CSL 241 Management Information System 4 Credits (3-1-0) An Overview of Management Information Systems, Types of information systems, Information System, Foundation of Information Systems in Business, Information system in business, The Components of Information system, Business Applications of Information Technology, Managing 205 P a g e Information Technology, Security and control Issues in Information system CSL 251 Internet & E-Commerce 4 Credits (3-1-0) Introduction to Internet Basic, Internet Connectivity, Internet accounts by ISP, Common terminologies, Addressing in Internet, Network topologies, Designing Pages with HTML, Introduction to JAVA script VB Script and Front Page, Internet Security Management Concepts, Information Privacy and Copyright Issues, Ecommerce, Potential of electronic commerce CSL261 Computer Organization and Architecture 4 credits (3-1-0) Digital Logic, The Computer System, Computer function and Interconnection, Computer functions, Interconnection Structures, Central Processing Unit, Instruction set, characteristics & functions, Control Unit, Control Unit Operation, Parallel Organization, Microprocessor organizations CSL 305 Database Management Systems 4 Credits (3-1-0) An Overview of the Database Management System, An Architecture of the Database system, Three levels of architecture, Role of database administrator (DBA), Relational Database Management System (RDBMS), Database Design, Relational Algebra and Relational Calculus, Normalization, The SQL Language Backup and Recovery, Security, Integrity, Design and Development of Database Applications CSL 306 Principles of Programming Languages 4 Credits (3-1-0) The Role of Programming Languages, Language Description, and Imperative Programming, Statements, Structured Programming, Types, Data Representation, Procedure Activations, Introduction to Procedures, Parameter-passing Method, Object Oriented Programming, Groupings of Data and Operations, Class Declarations in C++, What is an Object, Functional Programming, Elements of Functional Programming, Functional Programming in a Typed Languages:- Exploring a List, Functional Programming with Lists, Other Paradigms, Logic Programming, An Introduction to Concurrent Programming CSL 424 Data Communication & Computer Networks 4 Credits (3-1-0) Data Communications, Introduction, Communication Systems, Communication Network Fundamentals Introduction, Switching techniques, Cell switching (ATM), Network topologies, Layering the communication process, Open Systems Interconnection (OSI) model, Media Access Control, Introduction, Access Techniques (STDM, FDMA, TDMA, Spread Spectrum techniques and CDMA, DSSS, FHSS), Network Components, Introduction, LAN Hardware, LAN Operating Systems, Link Control and MAC Protocols,

206 Local Area Network (LAN ), LAN topologies and protocols; IEEE 802 Standard, Wide Area Network (WAN), Wireless Networks, Security and Management CSL 432 Programming in Java 6 Credits (3-1-4) Overlaps with: CSL 712 C++ Vs JAVA, JAVA and Internet and WWW, JAVA support systems, JAVA environment, JAVA program structure, Constant & Variables, Data Types, Defining a Class, Inheritance, Visibility Control, Arrays, Strings, Vectors, Wrapper Classes, Interface, Creating Threads, Synchronization, Implementing Thread Local and Remote Applets, Applets Life Cycle, HTML Tags & Applets CSL 436 Introduction to Software 4 Credits (3-1-0) Overlaps with: CSL 740 Introduction, Software approach, SDLC, Software Crisis, Software Process, Software Requirement, Analysis and Specifications DFDs, Software Design, Design Concepts & Principle, Cohesion & Coupling, Software Testing, Validation and Verification, Software Maintenance: Software Maintenance Process and its types CSL 442 Web Technology 6 Credits (3-1-4) Web, History of the web, Growth of the Web, Protocols governing the web, Introduction to Cyber Laws in India, HTML, Introduction To HTML, XML, Introduction & features of XML, Common Gateway Interface (CGI), PERL, RMI, COM/DCOM, VBScript, Java Script CSL 582 Visual Programming Using.Net 4 Credits (3-1-0) Overlaps with: CSL 548 Architecture of the.net Framework Development Platform, The.Net Framework Class Library, Just-In-Time Compilation, Unified Classes, C# Language, Array and Strings, Object and Classes, Inheritance and Polymorphism, Interfaces, Networking and Sockets, Delegates and Events, Windows Forms(IDE Environment), Advanced Features Using C, Introduction to ADO.NET, Windows Forms and Controls in detail, ASP.NET, Themes and Master Pages Creating a Consistent Web Site, Net Assemblies and Attribute CSL 630 Data Structures & Algorithms 4 Credits (3-1-0) Prerequisite: CSL 103/CSL 120 Overlaps with: CSL 221 Analysis of Algorithm, Introduction to Algorithm Design and Data Structures, Elementary Data Structures: Arrays, linked lists, Linked stacks and queues, Abstract Data types Stacks and Queues, Trees Height balanced (AVL), B-trees, Hash Table, Hash Functions, Collision Resolution Strategies, Hash Table Implementation, Searching, Sorting and Complexity, Graphs CSL 671 AI & Expert Systems 4 Credits (3-1-0) General Issues and overview of AI, The AI problems, Problem Solving, Production systems, Control strategies, Heuristic Search Techniques, Knowledge Representation, Scripts, AI Programming Languages Introduction to PROLOG, Natural Language Processing and Parsing Techniques, Context Free Grammar Recursive Transition Nets (RTN); Augmented Transition Nets (ATN), Planning Overview, Probabilistic Reasoning and Uncertainty, Expert Systems, Knowledge acquisition, Fuzzy logic CSL 712 Internet and Java Programming 4 Credits (3-1-0) Overlaps with: CSL 432 Core Java, Java Applet, Introduction to AWT, Java Swing, JDBC, Java Servlets, Introduction to Java Server Pages (JSP) CSL 786 Software Architecture, Testing & Quality Assurance 4 Credits (3-1-0) Pre-requisites: CSL 740/CSL 436 Overlaps with: CSL 449 Software Testing and the related concepts, Software Testing Strategies, Testing tools, Technical Metrics for Software, Software Quality, QA Process and Quality, Software Quality Assurance, Software Quality Management, Software Configuration Management, SW Reliability, Software Safety and Hazards Analysis, Using project management software tools, Quality management CSL-874 Advanced Java programming 4 credits (3-1-0) Pre-requisites: CSL 712 Java Database Connectivity: JDBC Product, Types of Drivers, Two-Tier Client/Server Model, Three-Tier Client/Sever Model, Servlets, Servlet Interaction & Advanced Servlets, Life cycle of Servlet, Java Server Pages, JSP Technologies, RMI: RMI Architecture, EJB: Types of Enterprise Java beans, XML: What is XML?, XML Syntax Rules, Struts, Introduction to the Apache Struts Web Technologies with PHP 4 credits (3-1-0) Introduction to PHP, Installation and configuration, PHP Operators, Conditional Statements, PHP Looping, PHP Functions, Built in and user defined, MySQL Connect, Input validation, PHP with client side scripting language PHP Error, Code re-use 206 P a g e Mobile Communication

207 4 credits (3-1-0) Introduction, Mobile Computing, Wireless communication, GSM, CDMA, Mobile OS, Process Migration Task migration issue, Data issues, load balancing strategies, Mobile Data Networking, Mobile Agents Network aware mobile Programs Distributed Computing 4 credits (3-1-0) Characterization of Distributed Systems, Introduction, Resource sharing and the Web Challenges, Theoretical Foundation or Distributed System, Concepts in Message Passing Systems, Distributed Mutual Exclusion, Distributed Deadlock Detection, Agreement Protocols, Distributed Resource Management: Failure Recovery in Distributed Systems, Fault Tolerance, Transactions and Concurrency Control, Distributed Transaction, CSL-783Digital Image Analysis 4 credits (3-1-0) Digital Image Fundamentals, Imaging geometry, Image Enhancement, Filtering, Generation of spatial masks from frequency domain specifications, Image Restoration, Fundamentals of color image processing, Image Compression, Error free compression, Image Segmentation, Region oriented segmentation, Detection of discontinuities CSL-894 Advanced.NET with AJAX and MVC 4 credits (3-0-2) Concept of server side and client side languages, Events and Event Handling,Validation Controls, Rich Data Controls, ADO.NET:Creating a Database,Working with the Server Explorer, LINQ Basics,ASP.NET 3.5 and LINQ Security, Introducing ASP.NET AJAX, Simple servercentric, solution, Working with JSON, Exploring the Ajax server extensions, Setting up and Installing ASP.NET MVC, Getting Started with MVC, Creating an application in MVC, Web Techniques, MVC State Management, Designing Web API, Sending Mails CSL-889 Application Development with Android 4 credits (3-0-2) Java Fundamentals, Introduction of Android& Environment setup, Basic UI design, Working with Advance UI Controls: Spinner, List view, Menu, popupmenu, Adding Actionbar,dialogs like alert, toast, DatePicker,Time Picker, Storage in Android, Creating Google Map, Web Service & Parsing, Making call, sending SMS 207 P a g e

208 53 Department of Electrical Polytechnic EEP 109 Electrical & Electronics Workshop 1.5 Credits (0-0-3) The laboratory is divided into two parts. In the first part, the student is required to perform some set experiments of electrical stream. In the second part, the student is required to perform some set experiments of electronics stream. In both the parts, there are mostly study experiments such as study of symbol, Study, Connecting, Testing and Fault Finding of Fluorescent Tube and its Accessories Ceiling Fan with resistance type and Electronic Regulator. DEE 203 Basic Electrical 2.5 credits (2-0-1) D.C. Circuits - Resistance, specific resistance, Capacitance - Capacitance of an isolated sphere, Parallel plate capacitor, Magnetic Circuits - Behavior of magnetic circuits, Composite magnetic circuits, Phasor Algebra - Mathematical representation of a vector, A.C. Circuits - Behaviour of R, L and C in A.C. circuits with phasor diagrams, Polyphase System, Battery, Classification of Electrical Materials, Conducting Material, Insulating Materials, Magnetic Materials, Special Purpose Materials. DEE 204 Electrical Measurement and Instrumentation 3 Credits (2-0-2) Introduction to Measuring Instruments - Absolute & Secondary Instruments, Different Measuring Instruments - PMMC, moving iron and rectifier type ammeters and voltmeters, Measurement of Resistance, Potentiometers, A.C. Bridges, Brief study of CRO, Electronic voltmeter, Instrumentation System, Transducers, Measurement Physical Parameter Using Suitable Transducers, Instrument Transformers. DEE-205 Electrical Circuit Theory 3 Credits (2-1-0) Network Parameters, Network Theorems - Star-delta transformation, Superposition theorem, Reciprocity theorem, Resonance - Series resonance, Parallel resonance, Circuit Transients - Introduction to Laplace transform and inverse Laplace transformations, Two Port Network - z-parameters, y-parameters, h-parameters, ABCD- parameters, Complex Frequency and Pole-Zero diagrams - Concept of complex frequency, Poles and zeros of simple function. DEE 206 Electrical Machines I 4 Credits (2-1-2) D.C. Generator - Construction of D.C. machine, Lap and wave winding (Brief idea), Principle of D.C. generator, D.C. Motor - Different types of D.C. motor; Principle of D.C. motor; Concept of back emf, Transformer - Construction of single phase and three phase transformer; Principle of operation; Emf equation and Turn ratio; Idea of leakage reactance; Transformer phasor diagram: At no load, At load (Lagging, Leading and UPF); Equivalent circuit of single phase transformer. DEE 207 Power System I 3 Credits (2-1-0) Introduction - Electrical energy demand and electrical energy growth in India, Electrical energy growth in India, Electrical energy sources, Thermal Power Station - Selection of plant location, Block diagram of plant and its working, Hydro Electric Power Plants - Selection of site; Advantages and disadvantages of hydro power plant, Nuclear Power Station, Diesel Power Plants, Solar Energy, Wind Energy, Bio-Gas Energy, Ocean Energy. DEE 209 Electrical Workshop 3 Credits (2-0-2) Wire Joints - Different types of joints, their uses, Wiring, Fault Investigation and Testing, Automobile Electrical System, Domestic Appliances, Introduction of Electrical Maintenance, Maintenance and Repair of Storage Batteries, Maintenance and Repair of Transformers, Maintenance and Repair of D.C. Motors, Maintenance and Repair of A.C Motors, Maintenance and Repairs of Circuit Breakers, Safety Measures. DEL 202 Circuit Analysis 3 Credits (2-1-0) General Network Concept - Network Elements (Definition and examples): Active and passive, Linear and non-linear, Unilateral and bilateral, Lumped and distributed circuit parameters, Mesh and Nodal Analysis -Definition of branch, node, mesh, loop and tree, Kirchhoff's laws, Network Theorems- Superposition theorem, Reciprocity theorem, Thevenin's theorem, Norton's theorem, Laplace Transformation, Two Port Networks, Resonance, Line Filters. DME 207 Electrical and Electronics 2.5 Credits (2-0-1) D.C. Machines - Construction, Operation of D.C. generator, Operation of D.C. motor, Transformer - Construction of single phase transformer, Types of transformer, Principle of operation, Induction Motor, Industrial Drives, Electric Heating, Illumination, Instrumentation and Measurement, Semiconductor and P-N Junction Diode, Bipolar Junction Transistor, Digital Electronics, Power Electronics, Relays Contactors and Timers, Photo Electric Devices. DEE 301 Power Electronics and Drives 2.5 Credits (2-0-1) Introduction- Principle, construction, characteristics and ratings of: SCR, DIAC, TRIAC, UJT.Power Control Rectification-Phase control of SCR, Different phase controlling circuits R, RC, UJT (Pedestal and Ramp), transformer circuit.inverter-basic principle of inverter, Series inverter, Parallel inverter, Single phase voltage source 208 P a g e

209 inverter, Three phase bridge inverter, Applications, UPS.Chopper-Principle of chopper operation, Control strategies: Constant frequency system, Variable frequency system. DEE 302 Utilization of Electrical Power and Traction 2 Credits (2-0-0) Industrial Utilization-Advantages of electrical drives over mechanical drives, Electric Heating Principle of electric heating, Electric Welding-Principle of electric welding, Classification of electric welding, Resistance welding, Illumination-Terms used in illumination, Laws of illumination, Electrical sources of light, Traction Systems-Ideal traction system, Different systems of traction, Systems of electric traction, Systems of track electrification, Train Movement and Energy Consumption, Power Supply-System of supply of power for electric traction, Current collector for overhead systems. DEE 303 Estimating, Costing & Design of Electrical Installations 2.5 Credits (2-0-1) Wiring Materials and Accessories-Different electrical symbols, Brief description, General Principles of Estimating and Costing-Purpose and essential of estimating and costing, Earthing -Need of earthing, Pipe and plate earthing, Service Connection-General rules and regulation, Overhead and underground service connection, Plan Estimation of 1-φ and 3-φ Electrical load-installation plan, Single line-wiring diagram, Design of Distribution Lines-Design and estimate the material, Sub Station, Design of a Distribution Scheme for a Small Colony-Load survey, Load curves DEE 304 Electrical Designs and Drawing 3 Credits (2-0-2) Transformer Design-Single phase and three-phase core type distribution transformer,design of Winding-Definition of - Single and double layer winding, D.C. Machine Design- Choice of specific magnetic and specific electric loading,3- Phase Induction Motor Design-Choice of specific magnetic and specific electric loading, Alarm and Signal Circuits-Using contactors, designing and drawing schematic and wiring diagrams of alarm and signal circuits, Contactor Control Circuits, The circuit should incorporate remote control, interlocking, time delay, sequential operation, Panel Wiring Diagram -Panel wiring diagram for the following with usual protective devices. DEE 305 Fundamentals of Control System 3 Credits (2-1-0) Control System-Basic definition, Open loop and Closed loop systems, Control System Components-D.C. Servo motor, A.C. Servo motor, Time Domain Analysis-First order and second order system, Time domain specifications, Step response of first order and second order system, Frequency Response-Frequency domains analysis, Frequency domain specifications, Gain margin and phase margin, Polar plots, Root Locus-Introduction, Rules for constructing root loci, Root locus plots, Effect of Zeros and Poles on root locus. 209 P a g e DEE 306 Electrical Machines II 4 Credits (2-1-2) Induction Motor-Production of rotating magnetic field by two phase and three-phase supply, Construction of slip ring and squirrel cage motors, Single Phase Induction Motor- Construction, working principle and characteristics of following motors: Resistance start, Capacitor start & induction run, Alternators-Constructional features, Principle of operation, Winding factors, Synchronous Motors- Construction and principle of operation, Phasor diagram at no load and on load, Stability Analysis of Synchronous Machines. DEE 307 Power System II 3 Credits (2-1-0) Transmission and Distribution-Need and basic flow diagram of power system, Materials used in Overhead Lines-Need, requirement, construction and special feature of line supports, Mechanical Design-Sag and span, Sag calculation in overhead lines with same and different level supports, Electrical Design-Overhead line constants, Classification of lines, R, L, C, of over head lines,d.c. Distribution Systems- Layout of distribution system, feeders, distributors and service mains, A.C. Distribution Systems, Construction of Underground Distribution Lines-Underground cables. DEE 308 Power System III 3 Credits(2-1-0) Load and Load Curves-Types of load, Variation in demand, chronological load curve,economic Aspects of Generation- Factor affecting the cost of generation, Tariffs-Objectives of tariff, General tariff form and types of tariff, Power Factor Improvement-Meaning of power factor, Causes of low power factor, Combined Operation of Power Stations- Extra High Voltages Transmission-Introduction, Need for EHV transmission, HVDC Transmission-introduction, Types of DC links, Corona-The Phenomenon of Corona, Disruptive critical voltage, Visual critical voltage, Corona Loss. DEE 309 Switchgear and Protection 3 Credits (2-1-0) Faults in Power System-Sources of faults, Percentage reactance and base KVA, Symmetrical Components- Operator 'a', Determination of sequence components, Fuses- Definition of different terms, Selection of fuse materials, Circuit Breakers-Basic construction of circuit breaker, Arc phenomenon, Protection-Principle of protection systems, Basic requirement of relays, Protection of Alternator-Field failure, Field earth fault, Over current, Transformer Protection-Over current, Earth fault, Differential protection, Buchholz relay, Line Protection. DEE 310 Energy Management 2 Credits (2-0-0) Energy Management and Energy Planning-Definitions and Significance, Energy Strategy, Energy Policy and Energy

210 Planning, Energy and Power Management-Overview of India's Energy and Power Sector, National Energy Strategies of India, Energy Audit-Aim of Energy Audit, Energy flow diagram, Strategy of Energy Audit, Comparison with Standards-Energy Conversations, Introduction, Motivation for Energy Conservation, Principles of Energy Conservation, Energy Conservation planning, Environmental Aspects of Energy and Pollution Control. DEL 305 Power and Industrial Electronics 3 Credits (2-0-2) Introduction - Principle, Construction and characteristics of SCR, TRIAC, DIAC, UJT, PUT, Power MOSFET, LASCR, solar cell, Power Control and Rectifiers, Inverters, Choppers and Cyclo-converters - Basic principle of inverters, Series and parallel inverter circuits using SCR (Single phase); Basic idea of PWM inverter; Chopper, AC Stabilizer and Power Supply, A.C., D.C. Motors & control, Heating, Welding and their Application. 210 P a g e

211 54 Polytechnic Electronics Department DEE 201 Basic Electronics 2.5 Credits (2-0-1) Semi Conductor Diode - Basic Introduction of P-N junction diode; Semiconductor diode as half wave rectifier and full wave rectifier, their efficiency and ripple factor; L filter, C filter, LC section filter, π Section filter, Bi-Polar Junction Transistors, R-C Coupled and Power Amplifier, Special Devices- Construction, operation, equivalent circuit and characteristics of: JFET, MOSFET, CMOS, Semiconductor photo devices such as LED, LDR, photo transistor, varactor diode, Feed Back and Oscillators, Classifications of Electrical Signals, Logic Gates, Boolean Algebra, Combinational Circuits, Sequential Circuits. DCS 204 Basics of Electronic Devices and Circuits 3 Credits (2-1-0) Semiconductor and PN Junction - Intrinsic and Extrinsic Semiconductors; Bipolar Junction Transistor (BJT) - Constructional details of PNP and NPN transistors, Working of a transistor, Transistor Biasing and Bias Stability- D.C. and A.C. Load line; Operating point and its stability, Field Effect Transistor - Construction, operation and characteristics of JFET, E and D MOSFET, Rectifiers, Power Supplies & Sensors. DCS 205 Basics of Digital Electronics 3 Credits (2-0-2) Introduction - Digital signal and its representation, advantages of digital techniques, Number System - Decimal, binary, octal and hexa-decimal number system, Conversion of a number from one system to another system, Logic Gates & Families - Introduction, Symbol and truth table of NOT, AND, OR, NAND, NOR, EX-OR and EX-NOR gates, Boolean Algebra - Boolean operators, Postulates of Boolean algebra, Laws of Boolean algebra, Duality theorem, De' Morgan's theorem, Minimization Techniques (K-Mapping), Combinational Logic Design, Sequential Systems. DEL 201 Electronic Components and shop practice 3 Credits (2-0-2) Resistors - Classification of resistors; Colour coding, tolerance and various parameters related with resistor; Capacitors - Classification of capacitors; Constructional detail, specification, application of various types of capacitors, Inductors and Coil - Classification of inductor; Construction detail, specification, application, Soldering and De-Soldering Techniques, Printed Circuit Board Fabrication, Transformer, Brief idea of surface mounted devices (SMD). DEL 203 Electronic Measurement and Instrumentation 3 Credits (2-0-2) Basic Concept of Measurement - Introduction; Generalized configuration of measuring system; Characteristics of measuring devices: Accuracy, Resolution, Precision, Expected Value, Error (Gross, Systematic and Random error), Transducers, Measuring Instruments, Range 211 P a g e Extension and Calibration, Signal Conditioning, Control System, Control System Components. DEL 204 Electronic Devices and Circuits 3 Credits (2-0-2) Semiconductor and PN Junction, Bipolar Junction Transistor (BJT), Transistor Biasing and Bias Stability, Field Effect Transistor, Rectifiers and Power Supplies, Filter Circuits- R- C circuit as high pass and low pass circuit, High pass circuit as a differentiator, Low pass circuit as an integrator, Response of high pass filter for step, pulse and square wave input (brief), Response of low pass circuit for step, pulse and square wave input, Clipper and Clamping Circuit. DEL 205 Digital Electronics 3 Credits (2-0-2) Introduction - Digital signal and its representation, Advantages of digital techniques, Boolean Algebra, Logic Gates, Minimization Techniques (K-Mapping), Combinational Logic Design, Sequential Systems - Introduction, truth table of R-S, J-K, M/S J-K,D,T flip-flops; Edge and level triggering; Shift registers, Universal shift register; Asynchronous and synchronous counters, Mod counters, Ring counters, Johnson counter; Programmable logic device (PLD): Programmable logic array (PLA), Programmable Array logic (PAL). DEL 206 Wave Propagation and Communication 2.5 Credits (2-0-1) Introduction- Basic component of communication; Definition of modulation; Need of modulation in communication, Definition of AM, FM, PM, PAM, PPM, PWM and PCM, EM Wave Propagation, Antennas, Noise and Cross Talk, Amplitude Modulation, Frequency Modulation, Radio Receivers - Various types of receivers; Receiver characteristics and their measurements; Electronic tuning system. DEL 208 Audio And Video System 2.5 Credits (2-0-1) Basic Components of Audio and Video - Construction & Working of Microphone, Construction & Working of Loud Speaker, CCD Camera, HI-FI and Stereophony, Scanning and Composite Video Signal - Scanning Process, Flicker & Inter lace scanning, Contrast Ratio & Aspect ratio and viewing distance, T.V. Signal Transmission, T.V. Receiver, Colour T.V. - Colour T.V. Essentials, Compatibility, Colour perception and three colour theory, Luminance, hue, saturation, chroma, Basic Concept of New Trends. DEL 209 Electronic Instruments 2.5 Credits (2-0-1) Multimeter - Principle of measurement of: D.C. Voltage and current, A.C. Voltage and current, Resistance, Electronic Voltmeter - Characteristics of different analog electronic voltmeter, Cathode Ray Oscilloscope (C.R.O) - Construction of CRT and deflection sensitivity, Block diagram of CRO, Various controls of CRO, Working Principle and Application

212 of, Digital Displays, Guarding Techniques - Safety guard and signal ground. DEL 301 Electronic Circuits 3 Credits (2-0-2) JFET and MOSFET Amplifiers, Multistage Amplifier - Different types of coupling: Direct coupling, R.C. coupling, Transformer coupling, Power Amplifier - Classification of power amplifier, Feedback Amplifier - Basic concept of feedback; Classification of feedback amplifier, Oscillators, Transistor at High Frequency and Special Circuit, Multivibrator, Blocking Oscillator and Time Base Generators. DEL 302 Advance Microprocessor & Microcontroller 3 Credits (2-0-2) 8086 Microprocessor - Internal architecture Bus interface unit, execution unit, internal registers and flag; Instruction execution sequence; Addressing modes; Modes of operation; Comparison with 8088, 8086 Instructions and Programming, I/O Data Transfer Schemes, Peripheral Devices and their Interfacing with 8085, Bus Standards - RS 232 C; IEEE 488, Introduction to 8051 Microcontroller. 3 Credits (2-0-2) IC Fabrication - Basic monolithic integrated circuit, Concept of SSI, MSI, LSI and VLSI, Operational Amplifier - OP AMP, symbol, equivalent circuit and characteristics.; Differential amplifier and its configurations, Timer Chip Functional block diagram and working; 555 Applications as: Saw tooth generator, BMV, AMV and MMV, PWM and PPM, Voltage Regulation, Phase Locked Loop, Design of Digital Circuits. DEL 308 Telecommunication & Switching Networks 2 Credits (2-0-0) Introduction - Evaluation of telecommunication - Definition of source, destination, subscriber - calling and called, Basics of a switching system; Electronic telephone hand set; Block diagram of cordless phone system; Brief idea of EPABX, Electronic Space Switching, Time Division Switching, Traffic Analysis - Network traffic load and parameters; Grade of service and blocking probability; Idea of Markov process; Incoming traffic and service time characteristics; Idea of delay system, Brief Idea of - PSTN; LAN; MAN; WAN. DEL 303 Advance Communication System 3 Credits (2-0-2) Pulse Modulation - General description of PAM, PWM, PPM; Pulse code modulation: Sampling and sampling theorem, Quantization, Digital Communication - Block diagram of Digital Communication system; Multiplexing - FDM, TDM: Basic concept of synchronization; Basic idea of digital modulation techniques: ASK, FSK, PSK, QPSK, Comparison of analog and digital communication, Information Theory, Facsimile System, Satellite Communication, Mobile Communication. DEL 304 Microwave and Optical Fiber 3 Credits (2-1-0) Microwave - Introduction; Microwave region and bands; Advantage and applications, Microwave Vacuum Tube Devices - Construction, working principle and application of: Klystron, Reflex klystron, Magnetron, Travelling wave tube, Microwave Solid State Devices Construction, working principles and application of: PIN Diode, Tunnel Diode, Gunn Diode, IMPATT Diode, Microwave Components, Microwave Measurements, Optical Fibre Communication. DEL 306 Bio-Medical Instrumentation 3 Credits (2-0-2) Introduction to Physiology - Physiological systems of the human body; Nerve physiology; Mechanism of respiration; Generation, propagation and distribution of action potentials, Medical Electrodes, Bio Medical Recording System, Electro Cardiograph (E.C.G.), Pace Makers, Blood Pressure Monitoring, Defibrillator, Biomedical Instruments, Bed Patient Monitoring System - Introduction; ICU/ CCU systems, Introduction to Bioinformatics, Use of Nanotechnology in biomedical (Brief idea). DEL 307 Linear Integrated Circuits & Design 212 P a g e

213 55 Polytechnic Mechanical Department AML 106 Applied Mechanics 4 credits (2-1-2) Force, Coplanar Forces, Moment, Application of Principles of Forces & Moments, Centre of Gravity, Friction, Simple Machines, Rectilinear Motion, Motion under Gravity, Projectiles, Newton's Laws of Motion, Impact and Collision, Circular Motion, Work, Power and Energy. MEP 107 Drawing 2 credits (0-0-4) Introduction of Drawing Instruments, Lines, Lettering and Dimensioning, Geometrical Construction and Curves, Scales, Theory of Orthographic Projections, Projection of Lines, Projection of Planes, Projection of Solids, Conversion of Pictorial Views into Orthographic Views, Orthographic Projections of Simple Solid Object from Pictorial / Isometric view, Section of Solids and Development of Surfaces, Isometric Projection, Sections and Conventions, Rivets and Riveted Joints Screw Threads and Fasteners, Foundation Bolt and Locking Devices. MEP 108 Workshop Practice 1.5 credits (0-0-3) Carpentry Shop-Preparation of Cross-Half Lap Joint, Preparation of Dovetail Joint, Preparation of Bridle Joint, Preparation of Mortise and Tenon Joint, Preparation of Mitre Joint, Demonstration of Job on Wooden Polishing Work, Welding and Sheet Metal-Preparation of a Butt Joint by Gas Welding, Preparation of Lap Joint by Electric arc Welding, Preparation of T-Joint by Electric arc Welding, Demonstration on Brazing by the Instructor, Demonstration on Soldering, Demonstration on Gas Cutting, Sheet Metal Shop, Plumbing shop. DME 201/DCE 201 Strength of Materials 3.5 Credits (2-1-1) Simple Stress and Strain-Various mechanical properties, Type of force, Hook's law, Young's modulus of elasticity, Tensile test diagram, Working stress and factor of safety, Principle of superposition, Bar of composite section, Shear stresses, Compound Stress-Introduction, Major principle stress, Minor principal stress, Mohr's circle method for principal stresses, Strain Energy, Bending Moments and Shear Force, Moment of Inertia, Bending Stresses in Beams, Shear Stress in Beams, Deflection, Columns and Struts, Torsion of Shaft, Springs, Thin Cylindrical Shells, Combined Direct and Bending Stress. DME 203 Materials and Processes 2.5 Credits (2-0-1) Materials, Classification and Properties of Materials, Structure of Metals and Their Deformation, Ferrous Metals, Non Ferrous Metals, Plastics and Fibers, Insulating Materials, Testing of Metals and Alloys, Fundamentals of Heat Treatment, Manufacturing Processes, Welding Process, Gas Welding, Electric Arc 213 P a g e Welding, Other Welding Processes, Modern Welding Methods, Foundry, Pattern, Die casting, Semi centrifugal, centrifugal, Shell moudling. DME 204 Theory of Machines 3 Credits (2-1-0) Simple Mechanism, Velocity and Acceleration in Mechanism, Dynamics of Reciprocating Parts, Friction, Transmission of Power, Balancing, Vibration, Governors, Methods of governing, Dead wt governors, Spring control governors, Concept of sensitivity, stability, isochronism, hunting, effort and power, Brakes and Dynamometer, brakes, Block and shoe brake, Band brake, Internal expanding brake; Functions of dynamometer, Prony brake, Rope brake and Froude's hydraulic dynamometer, Gyroscope. DME 205 Machine Drawing and Computer Aided Drafting 2 Credits (0-0-4) Machining Symbols and Tolerances, Working Drawing, Assembly Drawing, Gear tooth profile, Cam profile, Computer Graphics, Application software :- Introduction of CAD and similar software application like CATIA, Pro / Engineer and other; Getting Started I: Starting AutoCAD AutoCAD screen components Starting a drawing: Open drawings, Create drawings (Start from scratch, Use a template & Use a wizard) Invoking commands in AutoCAD Drawing lines in AutoCAD Co-ordinate systems: Absolute co-ordinate system, Relative co-ordinate system Direct distance method Saving a drawing. DME 206 Basic Automobile 2.5 Credits (2-0-1) Introduction-Classification of Automobiles, Suspension System-Basic functions of suspension system, Sprung and unsprung weight, Braking Systems-Purpose, principle,wheels and Tyres-Requirements of wheel, Types, Front axle and Steering System-Front axle, steering wheel, steering gear boxes, Power Transmission System-Clutch, Gear Box, Final Drive, Frame and Body, Frame, Body safety and economy considerations, Body alignment, Bumpers. DME 208 Thermodynamics and I.C. Engines 2.5 Credits (2-0-1) Basic Concept and Gas Laws, Laws of Thermodynamics, Availability, Formation of Steam and its Properties, Steam Generators, Boiler Performance, Gas Power Cycles, Principles of Internal Combustion Engines, Petrol Engines, Diesel Engines, Cooling, Lubrication and Governing, I.C. Engines Performance, Gas Turbines, Air Compressors- Classification of compressors, uses of compressed air; Description of single stage and multi stage reciprocating compressors; P.V. diagram of single and multi stage reciprocating compressor with inter cooling; Description of rotary and centrifugal compressors. DME 209 Workshop Technology and Metrology

214 3 Credits (2-0-2) Workshop Technology- Cutting Tools and Materials, Lathe Machine, Drilling Machines, Shaping, Planning and Slotting Machines, Cutting Fluids and Cooling Process, Metrology- Introduction to Metrology, Linear and Angular Measurement, Measurement of Surface Finish, Comparators, Light Wave Interference, Gear and Screw Measurement, Limits, Fits and Tolerance, Machine Tool Metrology, Alignment tests, Performance tests, Alignment test on lathe and drilling machine. DEE 202 Basic Mechanical 2.5 Credits (2-0-1) Mechanical Property of Metals, Basic Concept of Thermal, Hydraulics, Pressure Measuring Devices, Bernoulli s Theorem, Pumps, Turbine, Properties of Steam, Boilers, Steam Turbines, Engines, Transmission, Lubrication, Object of lubrication, Different methods of lubrication, Properties of lubricants. DCE 210 Computer Aided Drawing 1 Credit (0-0-2) Getting Started I - Starting AutoCAD, AutoCAD screen components, Starting a drawing, Getting Started II - Opening an existing file, Concept of Object, Object selection methods, Draw Commands, Editing Commands, Drawing Aids, Creating Text, Basic Dimensioning, Inquiry Commands, Editing Dimensions, Hatching, Blocks, Plotting Drawings in AutoCAD, Draw working plan. DEE 210 Management 2 Credits (2-0-0) Entrepreneurship, Entrepreneurship Support System, Setting up SSI, Raw Material Management, Marketing Facilities, Financial Sources for SSI, Contracts and Tenders, Project Report, ISO: 9000 Series of Quality System, Principles of Management, Human Resources Development, Wages and Incentives, Marketing Management, Tax System and Insurance, Labour Legislation and Pollution Control Acts. DME-301 Refrigeration and Air-Conditioning 3 Credits (2-0-2) Principles of Refrigeration, Refrigeration System, Refrigerants, Refrigeration System, Components and Controls, Refrigeration Applications, Production of Low Temperature, Pshychrometry, Air-conditioning, Physiological basis of air conditioning; Human comfort, metabolism in human body, comfort hart and effective temperature; Summer and winter design conditions; Classification of airconditioning systems, room air conditioners, package air conditioners; Air distribution system. DME-302 Processes in Manufacturing 3 Credits (2-0-2) Metal Forming Process, Conventional Metal Cutting Processes, Newer Machining Processes, Ultrasonic Machining, Abrasive jet machining, Electro chemical machining, Electro chemical grinding, Electrical Discharge Machining, Metallic Coating Processes, Plastic Process, 214 P a g e Injection moulding, Blow moulding, Compressive moulding, Jigs and Fixtures. DME-303 Thermal and Heat Transfer 3 Credits (2-0-2) Steam Nozzles, Steam Turbines, Steam Condenser, Air Pumps and Cooling Tower, Heat Transfer, Conduction, Convection, Radiation, Absorption, Reflection and transmission; Radiant energy distribution curve; Emissive power; Black body & white body; Grey body; Kirchoff s law; Wien s displacement law; Planks law & stefan boltzman s law; Radiosity; Shape factor. DME-304 CNC Machines & Automation 3 Credits (2-0-2) NC machines, CNC machines, DNC machines, Component of NC Machines, Classification of Numerical Control Machines, Constructional Details of CNC Machines, Tooling for CNC Machines, Fundamentals of Part Programming, Advanced Part Programming, Computer Aided Part Programming, Robotics, Robot terminology; Major Features of a robot: Manipulator, Controller, Sensors, Power supply unit, Automation in Manufacturing, flexible manufacturing system (FMS); Introduction to group technology (GT); Introduction to computer process planning (CAPP). DME-305 Power Generation 2 Credits (2-0-0) Introduction, Thermal Power Plants, Hydro-Electric Power Plant, Nuclear Power Plant, Nuclear reactors, Gas cooled reactors, Liquid metal cooled reactor, Fast breeder reactor; Nuclear power plants in India; Hazards in nuclear power plants and safety measures; Nuclear waste disposal, Diesel Power Plants, Gas Turbine Plants, Power Plant Economics, Renewal Energy Sources, Solar Energy, Wind Energy. DME-306 Advance Workshop Techniques 3 Credits (2-0-2) Metal Cutting Saws, Boring, Milling Machine, Grinding and Grinding Machines, Capstan and Turret Lathes, Automatic Machines, Metal Finishing Processes, Maintenance of Machine Tools, Installation and Testing of Machine Tools, Different types of machine foundation; Foundation plan; Machine tool testing. DME-307 Industrial 2 Credits (2-0-0) Production, Planning and Control, Inventory Control, Inspection and Quality Control, Work Study, Plant Location and Layout, Material Handling, Linear Programming, Depreciation, Obsolescence and amortization; Different methods of calculating depreciation. DME-308 Machine Design 3 Credits (2-1-0)

215 General consideration in machine design, Design of Welding Joints, Design of Screw and Bolts, Design of Joints, Design of simple cotter joints, Design of Keys and Couplings, Design of Shaft, Design of Components, Bearings, Material used for bearings and their properties, rolling contact bearings; Standard dimension and designations of ball bearings; Selection of rolling elements bearings, Lever-Design of a hand lever; Design of a foot lever; Design of Lever for safety valve. technique; Network Protocols: Concept and functions; HDLC; ISO-OSI reference model; X.25 interface; TCP/IP model. DME-309 Mechanical Estimating and Costing 3 Credits (2-1-0) Estimating, Costing, Elements of Costs, Break Even Analysis and Equipment Replacement Analysis, Estimation of Material Cost, Labour Costing, Estimation in Machining, Estimation in Welding Shop, Estimation in Forging Shop, Estimation in Pattern Making and Foundry Shop, Pattern allowances; Estimation of pattern cost; Estimation of foundry shop, Estimation in Sheet, Metal Shop, Sheet metal operations; Sheet metal joints; Estimation of time and cost in sheet DME-310 Management & Entrepreneurship 2 Credits (2-0-0) Principles of Management, Human Resources Development, Wages and Incentives, Material Management, Financial Management, Marketing Management, Entrepreneurship, Entrepreneurial Development, Product identification market survey, Entrepreneurship Support System, Setting up SSI, Tax System and Insurance, Financial Sources for SSI, Labour Legislation and Pollution Control Acts, Project Report, ISO: 9000 Series of Quality System. DEL 310 Management & Entrepreneurship 2 Credits (2-0-0) Principles of Management, Human Resources Development, Wages and Incentives, Material Management, Financial Management, Marketing Management, Entrepreneurship, Entrepreneurial Development, Entrepreneurship Support System, Setting up SSI, Tax System and Insurance, Financial Sources for SSI, Labour Legislation and Pollution Control Acts, Project Report, ISO: 9000 Series of Quality System. DEL 309 Computer Communication 2 Credits (2-0-0) Introduction: Need of computer communication; Analog and Digital data transmission; Brief idea of transmission media - guided and wireless; Network Fundamental: Network topology; General idea of LAN, MAN and WAN; Internet working; Switching techniques and their comparison: Circuit switching, Message switching, Packet switching; Simple idea of MODEM; Brief idea of ISDN; Data Link and Medium Access Framing; Error detection and correction cyclic redundancy check; Retransmission techniques: Retransmission strategies, Sliding window protocol; Medium Access Techniques: CSMA and CSMA CD, ALOHA and Slotted ALOHA; Backbone Networks: Routing Concepts: Shortest path, Flooding; Concentrators (HUB); Bridges and Routers; Congestion control basic concept leaky bucket 215 P a g e

216 56 Department of Management SML 101 MANAGEMENT CONCEPTS 4 credits (3-1-0) Introduction to Management Theory; the system approach to management. Systems methodology. Management style. Managers and their external environment. Introduction to planning: Nature and scope of planning, Type of planning, Long and short-term plans. Decisionmaking. Systems approach to decision-making. Organizing: Basic departmentation. Line and staff authority relationships. Functions of leadership, Nature of leadership, Control: The system and process of control, Control techniques, Control of overall perfomance. Introduction to functional areas of management: Operation Management, Financial Management, Marketing Management, Human Resources Management and Organization Management. SML 105 ACCOUNTING FOR MANAGERS 4 credits (3-1-0) Accounting principles underlying preparation of financial statements, Managerial uses of financial data. Ratio analysis and interpretation of financial statements. Cost Concepts. Cost volume-profit relationship and profit planning. Break even analysis. Incremental analysis and managerial decisions. Budgetary control system and preparation of various types of budgets. Time value of money. Cost of capital and capital budgeting. Determinants of working capital and its measurements. Cash management. Receivables management. Introduction to International Finance; Risk Management in International operations. SML 115 MANAGERIAL ECONOMICS 4 credits (3-1-0) Module I: Role of economic analysis in managerial decisions. Basic concepts; Objectives of business firms and profit policies. Theories of profit; Demand analysis and demand management w.r.t. domestic and world markets. Determinants, estimation and managerial uses of elasticities of demand; Demand forecasting; Supply function and market equilibrium analysis; Cost concepts; cost function; Breakeven Analysis; Equilibrium analysis of firm in an open economy. Module II: Pricing and output under different market situations; Recent advances in pricing theory and practices. Production analysis and Input Demand Functions; Project appraisal techniques. Social cost benefit analysis; Investment decisions under risk and uncertainty. Module III: National Income concepts and their interrelationships. Inflation analysis; (Indian) Monetary System and banking structure. Monetary policy analysis and its implications to industry. Issues of economic growth, development and planning. Managerial analysis of Indian Five Year Plans. Industrial development planning and strategy. Regulation of industry and business. Industrial sickness. Fiscal policy and its managerial implications. Business cycles and economic stabilisation. Balance of payments and Exchange Rate. 216 P a g e SML 201: INTRODUCTION TO BUSINESS ENVIRONMENT 4 credits (3-1-0) Module I: An overview of planning in India. Macro economic concepts: consumption, savings, investment. Objectives of economic policy. Nature of economic policies, Chronological survey of policy pronouncements and their impact on business: FEMA Completion policy. Industrial policy resolutions etc. Comparative economic systems. Dynamics of development Global business environment. Internal and External analysis. Module II: Business and government relations and government influences in income planning, prices and production policies. Impact of tax and inflationary parameters on corporate policy planning, Problem of determining planning horizon. Effect of uncertainties. Liberalization: Industry Policy and Trade Policy Coping strategies by Indian business, company formation and company Law. Module III: The nature of corporate strategy, Strategic Management in different contexts, Patterns of strategy development, explaining views on strategy development. Industry and Competitive Analysis, Generic Competitive Strategies, Offensive strategies, Defensive strategies, Vertical integration strategies, Flexibility in strategy. An overview of strategy formulation process, vision, mission, objectives. SML 202 MATHEMATICAL STATISTICS FOR MANAGEMENT DECISION 4 credits (3-1-0) To use students knowledge in basic analysis, calculus and Linear algebra to solve some interesting problems in Applied sciences and mechanics. Expansion in eigenfunctions, Fourier series and Fourier integral,orthogonal expansions, mean square approximation, completeness, orthogonal polynomials, and their properties, integral transforms and their applications, linear functional, general variation of a functional,direct variational methods for solution of boundary value problems, integral equations of voltera and Fredhlom type, seperable and symmetric kernels, Hilbert-Schmidt theory, singular integral equations, approximate methods of solving integral equations. SML 203 BUSINESS LAW 4 Credits (3-1-0) Module I: Nature of Business law, Sources of Business law and their classification. Mercantile law, Statue I Case law, Customs and Usage.Agreement and their legal obligations. Essential elements of a valid contract, Types of contact,void and voidable contract. Unenforceable and illegal agreements. Offer and acceptance over the telephone. Law of Arbitration-Definition of Arbitration, Effect of an arbitration. Arbitration without Intervention of Court. Powers and duties of Arbitrators. Module II: Sale of Goods Act. Definition and essentials of a contract of sale, Distinction between sale and agreement to sell, sale and hire purchase, sale distinguished from contract for work and labour. Kinds of goods, perishable goods. Document to the title of goods. Rules regarding transfer of property, Transfer of Title on sale. Rules regarding delivery

217 of goods. Buyers rights against seller, and unpaid seller s rights. Consumer protection act. Consumers rights, consumer s disputes redressal agencies, consumer protection council. Module III: Negotiable Instrumentd act. Definition and characteristic of Negotiable instrument. Liabilities of Parties to Negotiable Instruments. Brief exposure to Company law including incorporation of a company - object registration, article of association, raising capital from public, company management and reconstruction, amalgamation and winding up. SML 204 COST ANALYSIS AND CONTROL 4 credits (3-1-0) Meaning, nature and managerial need of cost analysis. Cost concepts and cost classification relating to income determination, profit planning, control and decision-making. Elements of costs-material, labour and overheads. Allocation, absorption and apportionment of overheads; methods of allocation of overheads. Cost accounting systems-process and job (contract, unit and operating).costing for joint products and by-products. Full costing system. Variable costing, differential costing and decision-making. Budget and budgetary control; preparation of operating budgets, fixed and flexible budgets,cash budget. Cost-volume-profit relationship and profit planning. Standardcosting and variance analysis. SML 205 BUSINESS ETHICS AND CORPORATE GOVENANCE 4 Credits (3-1-0) Module I: Ethics in Business Historical perspective, culture and ethics in India, codes and culture. Economics and the Environment: green business, Ethics and Competition. The ethical code, social audit. A framework for analysis and action. The sphere of personal ethics: consequences, rights and duties, virtu and character. Role of objectiveity, practicability, judgement and balancing acts. The individual and the corporation. Module II: Ehtical Responsibilities. Ethical responsibilities of economic agents: role obligations, obligation to sharesholder, rights and, obligations to customers, obligations to pay taxes. Environmental protection. Corporate accountability, Ethical conflict, concern for the locality, Attitude to labour.ethics and Government policies and laws. Module III : Ehtics in Functions. Ethical responsibilities of organizations leader: power, leadership. Obstacles to ethical conduct. Pressures for conformity. Evaluation and rewards. Job pressures and issues. Organizational change. Ethics in use of Informatrion technology. Intellectural Property Rights. Ethics in Marketing. Ethics of advertising and sponsorship Freedom Vs StateControl. Acquisitons and MergeS, Multinational decision making:reconciling International norms. SML 211: CONCEPT & PRACTICE OF BUSINESS MANAGEMENT 3 Credits (3-0-0) 217 P a g e Management: Definition, nature, process, functions (Planning, Organizing, Directing & Controlling) & skills. Introduction, definition, goals, scope and fundamental concepts, contributing disciplines to OB, developments in OB, Introduction to HRM, Introduction to Marketing, Accounting: Meaning & Concept of Accounting, Accounting Information System, Accounting Process. Financial Management: Nature and objectives of financial management-role of finance manager, SML 302: ENTERPRENEURSHIP DEVELOPMENT 4 Credits (3-1-0) Self employment need and mode. Structural base of Indian economic life. Industrial sector in the national developmental life. Indices of technical entrepreneuship. Opportunity identification and opportunity generation for technical entrepreneurship. Problem solving, decision-making, conflict and change in a new industrial enterprise. Systems consideration in an entrepreneurial venture. Management reporting and information systems of a new business enterprise. Preparing for an entrepreneurial career. Issues in resource management. Managing innovations. IPRs & SMEs. SML 308 MANAGEMENT ACCOUNTING 4 credits (3-1-0) Accounting principles underlying preparation of financial statements, Managerial uses of financial data. Ratio analysis and interpretation of financial statements. Cost Concepts. Cost volume-profit relationship and profit planning. Break even analysis. Incremental analysis and managerial decisions. Budgetary control system and preparation of various types of budgets. Time value of money. Cost of capital and capital budgeting. Determinants of working capital and its measurements. Cash management. Receivables management. Introduction to International Finance; Risk Management in International operations. SML 309 PRODUCTION PLANNING & CONTROL 4 Credits (4-1-0) Introduction to production management, Product development, Inventory concepts, Introduction to work study, Maintenance management SML 310 CORPORATE ACCOUNTING 4 Credits (3-1-0) Accounting for Hire Purchase Installments, Financial Statements of Banking Companies Accounting, for Investment and Insurance Claims, Introduction to consolidated Accounts of Holding and Subsidiary Companies Holding and Subsidiary companies. SML 311 INCOME TAX 4 Credits (3-1-0) Introduction: The Income Tax Act 1961 The Finance Act Benami Transactions Act 1988 Tax Planning; Basic concepts, Head of Income: Computation of Income from salaries, Income from house property Profits and gains of

218 business or profession Capital gains and income from other sources, Clubbing, aggregation and set off, Assessment: Assessment of individuals, Tax Administration SML 312 ORGANISATIONBEHAVIOUR 4 credits (3-1-0) Module I Scope of organizations: Nature and function of organisations; individual organization environment interface; longitudinal thinking. Organisation Management: Theory, practice and major schools of thought, application potentials and possibility. Module II Organisational architecture: Systems perspective on organisations and contingency approach. The sociotechnical systems approach. Theory of organizational structures; Nature and consequences of structure; organisation process; IT & organisations. Module III Integrating the elements: Organisational culture; coping strategies- individual & organisational; Impact of environmental and cultural variables on organizational structure and style; organization design; mechanisation, automation and computerisation; Organizational interdependence and organizational evaluation. SML 325 STRATEGIC MANAGEMENT 4 Credits (3-1-0) Module I: Strategic Management Process.The Strategic fdsanagement Process, Flexible system view of Strategic Management,Strategic Situation Analysis, The use of scenario,structural analysis of the competitive environment, Competitive Advantage Profile, Industry foresight. Strategic Capability Analysis-Resource audit, value chain analysis, comparative analysis, financial analysis, SWOT analysis, core competencies, culture and stakeholder expectations, Global strategy. Module II: Strategy Formulation.Strategic Intent, Vision, Mission and objectives. Strategic architecture,crafting a strategy. Alaternate directions for strategy development..alternate methods for strategy development: Portfolio analysis,screening strategic option; Analysing return risk and feasibility, selectionof strategies. Strategies Alliances and Joint Ventures, Mergers & acquisition. Module III: Strategy Implementation.Implementing strategy:corporate Restructuring, Budgets, Policies, Best practices, Support Systems, Rewards. Culture and Leadership, Functional strategies. SML 331 BUSINESS ENVIRONMENT AND CORPORATE STRATEGY 4 credits (3-1-0) Introduction, Dimensions of the business environment, Economic Environment, and Political Environment, Social Environment and Technological Environment Corporate Social Responsibility, Consumer Movement, Business Ethics, Cross-Cultural Business Environment, Ecological Environment Protection: Green Management, Global Warming, Carbon Foot Printing, The Environment Protection Act 1986., strategy formulation, strategy implementation and strategic evaluation & control 218 P a g e SML 332 Management Accounting and Financial Management Meaning, Scope, Objectives and limitation of management accounting; CVP Analysis Introduction; CVP Assumptions and Uses; Break-Even Analysis: BE Point and Margin of Safety; Graphical presentation of CVP Relationship; Profit Graph. Current Assets Management Working Capital Management, Management of Cash and Marketable Securities, Receivables &Inventory Management, Capital Structure, Cost of Capital, Leverages, Dividend Payment Policy, Capital Budgeting Techniques of capital budgeting, long term sources of financing SML 412: FINANCIAL MANAGEMENT 4 credits (3-1-0) Module I: Aims and objectives of Financial Decisions. Integrated approach to Corporate Financial Decisions. Effect of Taxes on Financial Decisions. Capital Budgeting Decisions under conditions of Risk and Uncertainty. Unequal expected lives and investment outlays. Capital Asset Pricing Model: meaning, Systematic and Unsystematic risk, calculation of Beta, CAPM and Cost of Equity Capital. Business Valuation Cases and Problems. Module II: Capital Structure Decisions: Operating and Financial Leverage, Optimum Capital Structure and Capital Structure Theories, EBIT/EPS Analysis, Designing Capital Structure in practice. Cases and Problems. Module III: Divided Decisions: Dividend and Valuation- Walter s Model, Gordon s Model, Theory of Irrelevance of Dividends (MM Approach). Types and Determinants of Dividend Policy. Internal Financing and Dividend Policy. Stock Dividend (Bonus Shares) and Stock (Share) Splits. Lease Decisions: Fundamentals of Leasing, Types of Leases, Financial framework for evaluating Lease Versus Buy/Borrowing alternative. Mergers Acquisition and corporate restructuring Cases and Problems. SML 413 MARKETING MANAGEMENT 4 credits (3-1-0) Marketing Orientation; Consumer Behaviour; Segmentation; Forecasting product life cycle; Product decision; Pricing decision; Promotion; Distribution; Sales management; Marketing Information Systems; Market Planning and Control; Market Research; Cases and Exercises. SML 414 HUMAN RESOURCE MANAGEMENT 4 credits (3-1-0) Module I: Management of human resources- historical evolution of the field. Influences on the approach of management of human resources. Line and staff components of human resource management. Role of Human Resource management in a competitive business environment. Interpersonal dynamics. Module II: Building a task-person fit. Determining Human Resource requirements. Recruitment and selection process. Training and Development. Team Building, Leadership. Appraising employee performance.

219 Module III: Wage and Salary Administration. Collective bargaining and industrial relations, Quality of worklife. Cost- Benefit analysis of HR functions. Safety, Health and employee assistance programmes. Global reference points of Human Resources Management. SML 415 MANAGEMENT RESEARCH METHODOLOGY 4 credits (3-1-0) Module I: Research concepts; exploratory, descriptive and conclusive research. The market decision-making process and the need of different types of research. Types of marketing problems and type of marketing research activity. Sources of data; use and appraisal of existing information. Module II: Information from respondents, sampling design, scaling techniques and questionnaire design, interviewing, mail surveys. Information from experiment, experimental design for marketing, Movtivational research, Advertising research Analysis and reporting. Module III: Marketing information systems, Structure and design, its role in planning and control; the place of marketing research. SML 431 ORGANIZATION BEHAVIOR AND HUMAN RESOURCES 4 Credits (3-1-0) Understanding Human Behavior in Management, Motivation and Leadership, Interpersonal Relationship management, Human Resource Planning, Management and Development of HR. SML 432 Industrial Law 3 Credits (3-0-0) The Indian Contract Act, 1872; Essential of a valid contract, void agreement, performance of contracts, breach of contract and its remedies. Quasi-Contracts. The Companies Act, 1956; Nature and types of companies; formation; memorandum and articles of association, prospectus, shares and share capital, allotment of shares. The Sale of Goods Act, 1930; right of an unpaid seller, Consumer Protection Act, 1986: Concept & Nature, Objectives, Terminology and Right, The Negotiable Instruments Act, 1881; nature and types; negotiation and assignment; SML 756 Marketing Research 5 Credits (4-1-0) Introduction of Marketing Research, Value of Information in Decision Making, Research Design, Sampling, Data Collection, Data Processing and Tabulation, Interpretation and Research Report Writing, Multiple Regression, Factor Analysis, Cluster Analysis, Multidimensional Scaling, Conjoint Analysis, Report Writing, Types of Research Reports, Guidelines for Writing a Report, Writing a Report Format, Evaluation of Research Report SMD 500 PROJECT REPORT 2 Credits (0-0-4) A student will take up project under the guidance of a faculty member in an area of the student s choice. Projects are to be executed individually SML 501 INTERNATIONAL BUSINESS 5 Credits (4-1-0) Module I: Historical and economic background, firms and International Business. The global scene and the challenges ahead, challenges to free International Trade Political Risk, Protection, Accounting, Taxation and Legal practices. The International debt risks. Module II: Regional Issues. Global Monetary Institutions and Trade Agreements, Regional Trade Agreements and Facts. Socio-cultural context of International Business: European countries, U.S.A. developing of newly industrialized countries and Japan. Management of Multinational firms. Module III: Globalization of Indian Economy.Liberalization and globalization of Indian business. India s multinationals, Indian laws and policies relating to investment in India by international firms and outside India by Indian firms. SML 502 PROJECT MANAGEMENT 5 Credits (4-1-0) The nature of projects, the project as a non-repetitive unit production system, the project as an agent of change. Project Identification considering objectives and SWOT analysis, Screening of Project Ideas, Technical, Market, 219 P a g e

220 Financial, Socio-economic and Ecological Appraisal of a project. Work break down structure and network development. Basic Scheduling, Critical Path and four kinds of floats. Scheduling under probabilistic durations, Time Cost tradeoffs, Project Monitoring with PERT/Cost, Organizational aspects, Computer packages and Project Completion. SML 503 INDIRECT TAXATION 5 Credits (4-1-0) Canons of Taxation Indirect Taxes, Central Excise, Service tax & VAT, Customs, Central Sales Tax Act SML 504 AUDITING 4 Credits (3-1-0) Introduction to Auditing & Assurance Services, Professional Standards, Engagement Planning, Management Fraud and Audit Risk, Employee Fraud and the Audit of Cash Risk Assessment: Internal Control Evaluation, Revenue and Collection Cycle. SML 505 SUPPLY CHAIN MANAGEMENT 5 Credits (4-1-0) Historical evolution of SCM, Supply Chain components: Inbound logistics, Operations, Outbound logistics, Forecasting, Inventory strategy, Transportation Strategy, Warehouse management. Information Strategy for SCM, Role of Information Technology in SCM, Performance measurement, Organization design and structure for effective supply chain.\ SML 511 SECURITY ANALYSIS AND INVESTMENT MANAGEMENT 5 Credits (4-1-0) Module I: Investment Environment. Saving and Financial flows, Financial Intermediation, Investment in Corporate Securities and other Investment Outlets, New Issue market and Secondary Markets. Sources of investment information. Theoretical framework for investment Decision. Regulatory Framework of Securities Markets in India. Module II: Valuation of Securities. Valuation of Variable Income Securities (Equity Shares): Theory of Valuation- Earnings and Dividend Model. Fundamental Analysis,Aggregate Economic Analysis, Industry Analysis, Company Analysis, Technical Analysis, Growth Shares, Under and Overvalued Shares. Analysis of Fixed Income Securities like Preference Shares, Debentures/Bonds and other Financial Instruments. Interest Rate structure and yield to Maturity Curve. Convertible Bonds: Warrants and Options. Module III: Portfolio Management.General principles. Measures of Risk and Return, Required Rate of Return and CAPM, Markkowitz Portfolio Theory. Efficient Capital Market Theory. Alternative Efficient Market Hypotheses. Constructing the Optimum Portfolio Principles of Banking,Introduction to Banking operations,recent Trends of IT in Banking,Payment and Settlement systems, Introduction to Risk Management SML 513 TOTAL QUALITY MANAGEMENT 5 Credits (4-1-0) Module I: Introduction to TQM; Customer Orientation, Continuous Improvement, Quality, Productivity and Flexibility, Approaches and philosophies of TQM, Quality Awards, Strategic Quality Management, TQM and corporate culture, Total Quality Control; Basic Analytical tools-check Sheets; Histograms; Pareto charts, Cause and Effect diagrams; Flow charts. Module II: Statistical Process Control; Advanced Analytical tools-statistical Design of Experiments; Taguchi Approach; Cost of Quality; Reliability and failure analysis. FMECA, Quality Function Deployment, Benchmarking, Concurrent. Module III: Quality Teams, Employee practices in TQM organisations: Leadership, delegation; empowerment and motivation; role of communication in Total Quality, Quality Circles; Total Employee Involvement; Problem Solving in TQM- Brain storming; Nominal Group Technique Team process; Kaizen and Innovation; Measurement and audit for TQM; Quality Information Systems, ISO 9000 series of Quality Standards; TQM Implementation; Reengineering and TQM. SML 521 SERVICE INDUSTRY IN INDIA 5 Credits (4-1-0) Introduction to Services Marketing, The Customer Experience, Strategic Issues in Service Marketing Services and the Marketing Mix, Promotion and Communication of Services, Maximizing Services Marketing Potential, Challenges for Senior Management. SML 522 RETAIL PRACTICE IN INDIA 5 Credits (4-1-0) Introduction to Retailing, Understanding the Retail Customer, Store location and site evaluation, Purchasing systems, Merchandise pricing, Managing the Retail Store, Information system and Logistics. SML 531 STRATEGIC HUMAN RESOURCE MANAGEMENT 5 Credits (4-1-0) The nature of corporate strategy, Strategic Management in different contexts, Patterns of strategy development, explaining views on strategy development. Industry and Competitive Analysis, Generic Competitive Strategies, Offensive strategies, Defensive strategies, Vertical integration strategies, Flexibility in strategy. An overview of strategy formulation process, vision, mission, objectives. SML 512 BANKING SERVICE OPERATIONS 5 Credits (4-1-0) 220 P a g e

221 SML 541 IT IN MANAGEMENT Credits (3-0-2) Information System Concepts, Introduction, Data vs. Information, open system vs. closed system, Classification of IS in the organization, Information Quality Attributes, MS- Windows, MS-Word, MS-PowerPoint, Computer Communication Networks, Telecommunication and computer networks, interpersonal communication applications, MS- EXCEL, Database Management, Developing MS-Access Database, Building IS, Organizational System, Decision making, IS Security SML 542 BUSINESS POLICY & STRATEGY 4 Credits (3-1-0) Introduction, Strategic Management Process, Environmental Analysis: Need, Characteristics and Categorization of Environmental Factors, Analysis of Internal Resources: Strengths and Weakness, Resource Audit, Approaches: Value-Chain Approach to Internal Analysis, Formulation of Strategy: Approaches to Strategy formation, Major Strategy options Stability, Growth and Expansion, Diversification, Retrenchment, Mixed Strategy, Choice of Strategy. leaders, Change Mastery Understanding change Evolution of an organization SML 602 INDIAN ECONOMY 4 Credits (3-1-0) Financial management and sources of financing, Time value of money, Investment decisions, Financial Decisions, Cost of Capital, Reward and dividend policy SML 603 EXPORT, IMPORT POLICY & DOCUMENTATION 5 Credits (4-1-0) Introduction to Export Management, Selection of Products and Identification of Export Markets, Export Marketing Channels and Export Sales Contract, Export Finance and Pricing, Pre-shipment Finance, Formalities of Registration and Export Documentation SML 604 INSURANCE & RISK MANAGEMENT 5 Credits (4-1-0) Overview of Insurance & financial security, Principles & Products of Life Insurance Modern concepts of Life insurance, Life Insurance premium & policy services Factors that affect premium, Annuities and Pensions Purpose of Annuity contracts, Introduction to commercial General insurance Historical background. SMD 600 PROJECT REPORT 2 Credits (0-0-4) A student will take up project under the guidance of a faculty member in an area of the student s choice. Projects are to be executed individually. SML 605 E- COMMERCE 4 Credits (3-1-0) Infrastructure for electronic Commerce, E-Commerce Architecture, Electronic Payment System Real World Payment models, Shopping cart technology, Security Threats to Networks, Inter/Intra Organizational Electronic Commerce EDI SML 611 INDIAN FIANCIAL SYSTEM 5 Credits (4-1-0) Business Environment, Emergence of Micro, Small and Medium (MSME) enterprises and Role of Institutions, Assessment of Fiscal, Monetary Policy and Price Stability for last Five years, Competition commission, Agriculture and Business, Balance of payment and Balance of Trade. SML 601 FUNDAMENTAL OF LEADERSHIP 4 Credits (3-1-0) The Mystique of Leadership Difference between leadership and management, Path to Leadership Learning, the learning organization, Leadership Culmination Classification of SML 612 INTERNATIONAL FINANCIAL MANAGEMENT 5 Credits (4-1-0) Globalization and the Multinational Firm, Foreign Exchange Market, Balance of Payments, International Capital Markets, Hedging and Risk Management, Transaction Exposure, Managing Economic and Translation Exposure Strategic Decision-Making in International Finance, Foreign Direct Investment, Managing Net Working Capital, International Trade Finance SML 623 LABOUR LAW AND INDUSTRIAL RELATIONS 5 Credits (4-1-0) 221 P a g e

222 Definition and concept of industrial relations, Emerging trends, Historical Development of payment systems, Theories of Wages, Factories Act, 1948, Industrial Employment (Standing Order) Act, 1936Trade Union Act, 1926, Industrial Disputes Act, SML 621 INDUSTRIAL MARKETING CONCEPT & PRACTICE 5 Credits (4-1-0) Dimensions of industrial marketing, Strategy formulation in the industrial market Formulating product planning, Formulating marketing communication planning, Formulating pricing policies SMD 700 PROJECT REPORT 2 Credits (0-0-4) A student will take up project under the guidance of a faculty member in an area of the student s choice. Projects are to be executed individually. SML 760 MARKETING MANAGEMENT 4 credits (3-1-0) Marketing Orientation; Consumer Behaviour; Segmentation; Forecasting product life cycle; Product decision; Pricing decision; Promotion; Distribution; Sales management; Marketing Information Systems; Market Planning and Control; Market Research; Cases and Exercises. SML 641 PERSONLAITY DEVELOPMENT 3 Credits (2-0-2) Personality Development and Soft Skills, Group Discussions and Job Interviews, Book Reading and presentation, Current News Awareness, Live Projects SML 642 MANAGERIAL EFFECTIVENESS 4 Credits (3-1-0) Managerial Effectiveness, Creativity Management, Stress Management, Interpersonal Skills, Emotional Intelligence in Management, Leadership and Change Management, Time Management, Multi-Cultural Communication Skills SML 731: HUMAN RESOURCE MANAGEMENT 4 credits (3-0-0) Module I: Management of human resources- historical evolution of the field. Influences on the approach of management of human resources. Line and staff components of human resource management. Role of Human Resource management in a competitive business environment. Interpersonal dynamics. Module II: Building a task-person fit. Determining Human Resource requirements. Recruitment and selection process. Training and Development. Team Building, Leadership. Appraising employee performance. Module III: Wage and Salary Administration. Collective bargaining and industrial relations, Quality of worklife. Cost- Benefit analysis of HR functions. Safety, Health and employee assistance programmes. Global reference points of Human Resources Management. SML 705: FINANCIAL MANAGEMENT 4 credits (2-0-2) Module I: Aims and objectives of Financial Decisions. Integrated approach to Corporate Financial Decisions. Effect of Taxes on Financial Decisions. Capital Budgeting Decisions under conditions of Risk and Uncertainty. Unequal expected lives and investment outlays. Capital Asset Pricing Model: meaning, Systematic and Unsystematic risk, calculation of Beta, CAPM and Cost of Equity Capital. Business Valuation Cases and Problems. Module II: Capital Structure Decisions: Operating and Financial Leverage, Optimum Capital Structure and Capital Structure Theories, EBIT/EPS Analysis, Designing Capital Structure in practice. Cases and Problems. Module III: Divided Decisions: Dividend and Valuation- Walter s Model, Gordon s Model, Theory of Irrelevance of Dividends (MM Approach). Types and Determinants of Dividend Policy. Internal Financing and Dividend Policy. Stock Dividend (Bonus Shares) and Stock (Share) Splits. Lease Decisions: Fundamentals of Leasing, Types of Leases, Financial framework for evaluating Lease Versus Buy/Borrowing alternative. Mergers Acquisition and corporate restructuring Cases and Problems. 222 P a g e SML 721: CORPORATE BUSINESS ENVIRONMENT

223 4 credits (3-1-0) Module I: An overview of planning in India. Macro economic concepts: consumption, savings, investment. Objectives of economic policy. Nature of economic policies, Chronological survey of policy pronouncements and their impact on business: FEMA Completion policy. Industrial policy resolutions etc. Comparative economic systems. Dynamics of development Global business environment. Internal and External analysis. Module II: Business and government relations and government influences in income planning, prices and production policies. Impact of tax and inflationary parameters on corporate policy planning, Problem of determining planning horizon. Effect of uncertainties. Liberalization: Industry Policy and Trade Policy Coping strategies by Indian business, company formation and company Law. Module III: The nature of corporate strategy, Strategic Management in different contexts, Patterns of strategy development, explaining views on strategy development. Industry and Competitive Analysis, Generic Competitive Strategies, Offensive strategies, Defensive strategies, Vertical integration strategies, Flexibility in strategy. An overview of strategy formulation process, vision, mission, objectives. SML 732: BUSINESS STRATEGY 4 Credits (3-1-0) Introduction, definitions, industrial motivation, Evolving Industrial Competition( multi attributed competition), flexibility, integration and automation in enterprises, growing Need for Knowledge and its effective Management (KM), role of IT, KM and challenges of CIMS, intelligent manufacturing, ERP, SCM and CRM, e-manufacturing etc. KM technical concepts: (dat vs information vs knowledge), The Knowledge Edge, Knowledge, KM Framework (process steps), Aligning KM with Manufacturing Strategy, Business Strategy etc., design and deployment of KM in industrial enterprises( KM team, KM system analysis, Developing Effective Systems, Knowledge Audit), IT based tools, role of performance measurement, KM and competitive link, intelligent manufacturing, agile enterprises, cases, presentations, group exercises. Role of Simulation and Intelligent Systems, KM Deployment, Managing Innovation, Performance Measurement, Applications. SML 762 SERVICE MARKETING 4 Credits (3-1-0) Introduction to Services Marketing, The Customer Experience, Strategic Issues in Service Marketing Services and the Marketing Mix, Promotion and Communication of Services, Maximizing Services Marketing Potential, Challenges for Senior Management. SML 735 TRAINING AND DEVELOPMENT 4 credits (3-1-0) Building a task-person fit. Determining Human Resource requirements. Recruitment and selection process. Training and Development. Team Building, Leadership. Appraising employee performance. SML 736 PERFORMANCE MANAGEMENT AND REWARD SYSTEM 4 Credits (3-1-0) The Foundation Of performance management, Performance Planning and Management, Competency, Analysis and Competency Mapping, Performance Evaluation, Reward systems and Performance, Performance, competence and skill based pay. SML 737 STRATEGIC HUMAN RESOURCE MANAGEMENT 4 Credits (3-1-0) The nature of corporate strategy, Strategic Management in different contexts, Patterns of strategy development, explaining views on strategy development. Industry and Competitive Analysis, Generic Competitive Strategies, Offensive strategies, Defensive strategies, Vertical integration strategies, Flexibility in strategy. An overview of strategy formulation process, vision, mission, objectives. SML 745: OPERATIONS MANAGEMENT 4 credits (3-0-0) Module I: Managing operations; planning and design of production and operations systems. service characteristics. Facilities planning location, layout and movement of materials. Line balancing. Analytical tools and techniques for facilities planning and design. Module II: Production forecasting. Aggregate planning and operations scheduling, Production Planning and Control. Purchasing, Materials Management and Inventory control and JIT Material Requirements Planning. MRPII, ERP, Optimization techniques applications. Module III: Work Study, Value, Total quality & statistical process control. Maintenance management and equipment policies. Network planning and control. Line of Balance, World class manufacturing and factories of the future, Case studies. SML 751 Real Estate Management 4 Credits (3-1-0) Introduction to Real Estate, Legal Framework For Real Estate, Environmental Issues in Real Estate, Professional Practices in Real Estate, Real Estate Valuation SML 753 CORPORATE TAX PLANNING 4 Credits (3-1-0) Introduction To Tax Management: Concept of tax planning, Tax avoidance and tax evasions, Corporate taxation and individual tax, Tax Planning For New Business, Tax Planning And Financial Management Decisions, Tax Planning And Managerial Decisions, Special Tax Provisions: Tax provisions relating to free trade zones, Infrastructure sector and backward areas, Tax incentives for exports, Tax Issues Relating To Amalgamation, Tax Payment: Tax deductions and collection at source, Advance payment of tax. 223 P a g e

224 SML 754 Education Management Credits (3-1-0) for Healthcare / Hospital. Education as a System, Principles and Techniques of Management for Educational Administrators, Technologies For Learning, Finance and Marketing in Education, Legislation and Emerging Issues Related To Education Management. SML 755 MANAGEMENT OF CONTROL SYSTEM 4 Credits (3-1-0) The conceptual foundations of control systems, The traditional instruments of control in organizations External audit, internal controls, internal audit, role of financial controllers, budgetary control, The new dimensions of control with strategies Behavioral aspect of management control Management Control in Specialized organizations Sectoral applications. SML 756 MARKETING RESEARCH 4 Credits (3-1-0) Introduction to Market Research Types of Sources and collection of Marketing Data, Market Research Techniques, Sampling, Questionnaire & Scaling Techniques. Probability and Non Probability Sampling, Sampling methods, Sample Design. Questionnaire design and drafting. Scaling techniques like Nominal, Ordinal, Interval, Ratio, Perceptual Map, Semantic Differential, Likert, Rating & Ranking Scales, Setting up & Implementation of Marketing Research Project. Steps in formulating Market Research Projects, Illustrations/cases to be discussed for following topics of above mentioned chapters. Data collection methods, test marketing, focus group interviews, internet interviewing, sample design, questionnaire construction, scaling techniques. SML 761 CONSUMER BEHAVIOR 4 Credits (3-1-0) Consumer Behavior-Introduction, Marketing research, Marketing information system, Social Class, Culture - influence on behavior. SML 763 RETAIL MANAGEMENT 4 Credits (3-1-0) Introduction to Retailing, Understanding the Retail Customer, Store location and site evaluation, Purchasing systems, Merchandise pricing, Managing the Retail Store, Information system and Logistics. SML 794: COMMUNICATION SKILLS AND PERSONALITY DEVELOPMENT 3 credits (2-0-2) Introduction to major grammatical models. Phonological and syntactical structure of present-day English. Langauge of science and technology. Aspects of style. Some common errors. Technical presentations design and delivery. Audio Visuals in communication. Collecting materials for research. Organization of research paper/dissertation. SML 757 Hospitality Management 4 Credits (3-1-0) Introduction to Hotel Industry, Front Office Procedures and House Keeping Procedures, Hospitality Marketing, Sales Techniques for hotel industry, Hospitality law. SML 758 Health Care Management 4 Credits (3-1-0) Principles of Health Service Management, Organization & Administration of Supportive Services, Organization and Administration of Clinical and Super Specialty Service, Healthcare Marketing Management, Health Policy and Healthcare Services Delivery, Human Resource Management and Labour Legislation, Legal Framework in Healthcare, Hospital Management Information Systems, Logistics and Supply Chain Management, Quality Assurance 224 P a g e

225 4 Credits (3-1-0) Introduction, Management of Commercial Banks, Management of Non-Banking Financial Institutions, Insurance & Mutual Fund organizations, Management of Financial Services SML 801 BUSINESS ETHICS AND CORPORATE GOVENANCE 4 Credits (3-1-0) Module I: Ethics in Business Historical perspective, culture and ethics in India, codes and culture. Economics and the Environment: green business, Ethics and Competition. The ethical code, social audit. A framework for analysis and action. The sphere of personal ethics: consequences, rights and duties, virtu and character. Role of objectiveity, practicability, judgement and balancing acts. The individual and the corporation. Module II: Ehtical Responsibilities. Ethical responsibilities of economic agents: role obligations, obligation to sharesholder, rights and, obligations to customers, obligations to pay taxes. Environmental protection. Corporate accountability, Ethical conflicts, concern for the locality, Attitude to labour.ethics and Government policies and laws. Module III : Ehtics in Functions. Ethical responsibilities of organizations leader: power, leadership. Obstacles to ethical conduct. Pressures for conformity. Evaluation and rewards. Job pressures and issues. Organizational change. Ethics in use of Informatrion technology. Intellectural Property Rights. Ethics in Marketing. Ethics of advertising and sponsorship Freedom Vs StateControl. Acquisitons and MergeS, Multinational decision making:reconciling International norms. SML 811 INDUSTRIAL MARKETING 4 Credits (3-1-0) Dimensions of industrial marketing, Strategy formulation in the industrial market, Formulating product planning, Formulating marketing communication planning, Formulating pricing policies. SML 813 ADVERTISING, BRAND, MEDIA MANAGEMENT 4 Credits (3-1-0) Advertising Objectives and Planning, Steps in advertising strategies & Views of Thinkers Creative strategy, Other issues in Advertising & Law & Practices Comparative Advertisement, Brand Management Brands and Their significance. SML 821 PORTFOLIO MANAGEMENT AND MUTUAL FUNDS 4 Credits (3-1-0) Valuation of securities, Efficient Market Hypothesis, Capital Market Theory, Portfolio Performance Evaluation, Managing Financial Risk with Derivatives. SML 822 MANAGEMENT OF FINANCIAL SERVICE 225 P a g e SML 823 ADVANCED MANAGEMENT ACCOUNTING 4 Credits (3-1-0) Accounting for Hire Purchase Installments, Financial Statements of Banking Companies Accounting, for Investment and Insurance Claims, Introduction to consolidated Accounts of Holding and Subsidiary Companies Holding and Subsidiary companies. SML 831 LEADERSHIP SKILLS AND CHANGE MANAGEMENT 4 Credits (3-1-0) The Mystique of Leadership Difference between leadership and management, Path to Leadership Learning, the learning organization, Leadership Culmination Classification of leaders, Change Mastery Understanding change Evolution of an organization SML 832 LABOUR LAW AND COMPENSATION MANAGEMENT 4 Credits (3-1-0) Objectives of performance appraisal Organizational uses of performance appraisal, Emerging trends Recent Trends in Performance appraisal systems; team based appraisal, Historical Development of payment systems Basic concept, Wage Legislations Payment of wages act, Theories of Wages Maslow hierarchy of needs. SML 833 HUMAN RESOURCE PLANNING 4 Credits (3-1-0) Definition of human resource Planning objectives of human resource planning: human resource planning at different levels-the process of human resource planning: assessing current human resources. Growing importance to human resource planning. SML 850: MANAGEMENT OF INFORMATION TECHNOLOGY 4 credits (3-1-0) Module I The Strategic Framework for IT Management. Emerging information technologies: IT for competitive advantage; ITfor internal effectiveness; IT for interorganizational linkage; Module II Strategy Development and Planning Techniques. Module II: IT Planning (CSFs, Scenario analysis, Linkage analysis, Enterprise modeling); Strategy formulation techniques; Nolan s stage model and revised models for Nolan s stages; IT investment decisions; methods for evaluating IT effectiveness; IT enabled business process redesign. Module III : Strategic Issues Related to IT Management. Relating IT to organizational leadership, culture, structure,

226 policy and strategy; programmer productivity; Managing legacy systems; evaluating centralization- issues; ITforecasting. Module III: Marketing information systems, Structure and design, its role in planning and control; the place of marketing research. SML 873 SECURITY ANALYSIS AND INVESTMENT MANAGEMENT 4 Credits (3-1-0) Module I: Investment Environment. Saving and Financial flows, Financial Intermediation, Investment in Corporate Securities and other Investment Outlets, New Issue market and Secondary Markets. Sources of investment information. Theoretical framework for investment Decision. Regulatory Framework of Securities Markets in India. Module II: Valuation of Securities. Valuation of Variable Income Securities (Equity Shares): Theory of Valuation- Earnings and Dividend Model. Fundamental Analysis,Aggregate Economic Analysis, Industry Analysis, Company Analysis, Technical Analysis, Growth Shares, Under and Overvalued Shares. Analysis of Fixed Income Securities like Preference Shares, Debentures/Bonds and other Financial Instruments. Interest Rate structure and yield to Maturity Curve. Convertible Bonds: Warrants and Options. Module III: Portfolio Management.General principles. Measures of Risk and Return, Required Rate of Return and CAPM, Markkowitz Portfolio Theory. Efficient Capital Market Theory. Alternative Efficient Market Hypotheses. Constructing the Optimum Portfolio SML 876 PROJECT APPRAISAL PLANNING AND CONTROL 4 credits (3-1-0) Capital investments Analysis of Demand and Situational, Financing of projects, Investment criteria, Project financing in India, Managing E-Business projects. SML 877 BANKING SERVICE OPERATIONS 4 Credits (3-1-0) Principles of Banking,Introduction to Banking operations,recent Trends of IT in Banking,Payment and Settlement systems, Introduction to Risk Management SML 895: MANAGEMENT RESEARCH METHODOLOGY 4 credits (2-0-2) Module I: Research concepts; exploratory, descriptive and conclusive research. The market decision-making process and the need of different types of research. Types of marketing problems and type of marketing research activity. Sources of data; use and appraisal of existing information. Module II: Information from respondents, sampling design, scaling techniques and questionnaire design, interviewing, mail surveys. Information from experiment, experimental design for marketing, Movtivational research, Advertising research Analysis and reporting. 226 P a g e

227 227 P a g e