Material Safety Data Sheet

Transcription

1 Rod Grease Tacky I. PRODUCT AND COMPANY IDENTIFICATION Product Name: Rod Grease Tacky Revised: 7/2010 Chemical Name: Petroleum Lubricating Grease Chemical Family: Hydrocarbon Supplier: NOV FluidControl 4310 N. Sam Houston Parkway E Houston, TX Office: (713) Fax: (713) Company website: Emergency Telephone Number: CHEMTREC: or International II. COMPOSITION Material or Component CAS Number OSHA PEL Percentage III. Hazard Data: HAZARDS IDENTIFICATION Variable Among Individuals: Health studies have shown that many petroleum hydrocarbons and synthetic lubricants pose potential human health risks which may vary from person to person. As a precaution, exposure to greases, liquids, vapors, mists or fumes should be minimized. Eyes: This product may cause mild eye irritation. Direct exposure to vapors may cause stinging, tearing and redness. May aggravate existing conjunctivitis of the eye, based on data from components or similar materials. Skin: This material may be slightly irritating to the skin. Irritation and/or allergic skin reaction on prolonged and repeated contact may lead to various skin disorders such as dermatitis, oil acne, or folliculitis. Person with pre-existing skin disorders may be more susceptible to the effects of this material. Based on data from components or similar materials. Ingestion: Ingestion via minor contamination on fingers or food is not likely to cause any discomfort or adverse affects. Very gross amounts may cause irritation of the digestive tract (due to product consistency), nausea and vomiting. Aspiration into the lungs during ingestion or vomiting may cause mild to severe pulmonary injury. Inhalation: Inhalation of vapors or mists may be harmful. Purposely breathing high concentrations of the heated vapors may cause light-headedness and nausea, irritate mucosal membranes of mouth, nose, and throat; and aggravate existing respiratory diseases. Chronic Health Effects: Product assessed in accordance with OSHA 29 CFR and determined not to be hazardous. D4A Rev02 Page 1 of 5

2 IV. FIRST AID MEASURES Ingestion: Get medical attention IMMEDIATLEY. Skin Contact: Flush with soap and water. Eye contact: Flush with plenty of water for at least 15 minutes. Get medical attention. Inhalation: Remove to fresh air. Get medical attention. Additional information: Wash hands thoroughly after handling. V. FIRE AND EXPLOSION DATA Flammability Fire Extinguishing Media No Carbon dioxide (CO 2 ), water fog, foam, dry chemical, earth or sand. Special Firefighting Procedures: Wear self-contained breathing apparatus when fighting fires in confined spaces. Water spray is an unsuitable extinguishing agent. Flashpoint ( o C) and method 175 o C / 346 o F ASTM D-92 Upper Explosion Limit (% by volume) Lower Explosion Limit (% by volume) Autoignition Temperature ( o C) Hazardous combustion products EXPLOSION DATA: Sensitivity to mechanical impact: Sensitivity to static discharge: VI. ACCIDENTAL RELEASE MEASURES Steps to be taken in case material is released or spilled: Remove sources of ignition. Immobilize with dry absorbent. Minimize skin contact. Keep product out of sewers and watercourses by diking or impounding. Immediately advise authorities if substantial quantities of product have entered or may enter sewers, watercourses, or extensive land areas. Assure conformity with applicable governmental regulations. Waste Disposal: Waste disposal should be in compliance with all federal, state, and local laws. Material, if discarded, is not expected to be a hazardous waste under RCRA. Suggested disposal is by burning for BTU values. D4A Rev02 Page 2 of 5

3 VII. HANDLING AND STORAGE Storage: Store product in a cool dry location. Keep away from potential sources if ignition. Keep away from incompatible materials. Avoid breathing vapors, or prolonged or repeated skin contact. Wash thoroughly after handling. Remove any contaminated clothing and launder before reuse. Empty Container Warning: Empty containers retain residue (semi-solid, liquid and/or vapor) and can be dangerous. Do not pressurize, cut, weld, braze solder, drill, grind, or expose such containers to heat, flame, sparks, static electricity, or other sources of ignition. They may explode and cause injury or death. Do not attempt to clean since residue is difficult to remove. Empty drums may be purchased by a reconditioner. All other containers should be disposed of in an environmentally safe manner and in accordance with governmental regulations. VIII. PREVETATIVE MEASURES Personal Protective Equipment: Gloves (specify): Eye (specify): Respiratory (specify): Other (specify): Oil Resistant Safety Glasses None needed None Engineering controls (e.g. ventilation, enclosed process, specify): Ventilation: Local exhaust. If necessary to maintain Permissible Exposure Limit or Threshold Limit value: If used in applications where a mist be generated, observe a PEL of 5mg/m 3 for mineral oil mist. Leak and spill procedures: Absorb with sand or inert material. Prevent spread or spill. Dispose of immediately. Shut off leak and dyke up large spills. Keep spills clear of flames and sparks. Waste Disposal: Dispose of in accordance with federal, provincial or local regulations. Handling procedures and equipment: Keep away from strong oxidizers, excessive heat and ignition sources. Storage requirements: Keep away from strong oxidizers, excessive heat and ignition sources. Special shipping information: No special conditions. D4A Rev02 Page 3 of 5

4 IX. PHYSICAL AND CHEMICAL PROPERTIES Physical State Solid Color/Appearance Brown Grease Odor Oil Odor Odor Threshold (PPM) Specific Gravity 0.99 Vapor Pressure (MM) Vapor Density (Air=1) Evaporation Rate (butyl acetate=1) Boiling Point ( o C) Freezing Point ( o C) Solubility in Water (20 o C) Insoluble % Volatile (by volume) 0% Melting Point Coefficient of water/oil distribution X. STABILITY AND REACTIVITY Chemical Stability: Yes Incompatibility to other substances Yes Materials to Avoid: Strong oxidizers. Keep away from excessive heat and ignitions sources Reactivity: Avoid open flames, sparks, and ignition sources. Hazardous decomposition products: CO, CO 2, oxides of sulfur are generated on combustion XI. TOXICOLOGICAL PROPERTIES OF MATERIAL Routes of entry: Skin Contact Eye Contact Ingestion Effects of acute exposure to material May cause mild irritation to the skin and eyes Effects of chronic exposure to material This product has been used for years with no known ill effects. LD 50 of material (specify species route): LC 50 of material (specify species & route): Exposure (limits): Irritancy of material: Sensitization of material: None Synergistic materials: Carcinogenicity, reproductive effects, teratogenicity, mutagenicity: This product contains no known carcinogens or mutagens as defined by OSHA or IARC. D4A Rev02 Page 4 of 5

5 XII. ENVIRONMENTAL INFORMATION Reportable quantity (RQ), EPA regulation 40 CFR 302 (Cercla section 102): None No known environmental hazards. SARA Title III: Section 313 reportable ingredients: none This product contains the following ingredient(s) which are listed under SARA section 313 at or above the deminimis concentration levels: none Section 311/312: immediate health (ingestion-unlikely under normal use conditions). California prop 65: This material is not manufactured to contain any chemicals known to the state of California to cause cancer or birth defects or other reproductive harm. XIII. TRANSPORATION INFORMATION DOT PROPER SHIPPING NAME: Non-Hazardous Lubricating Grease Class 65 DOT HAZARD CLASS: Not regulated DOT UN NUMBER: XIV. OTHER INFORMATION NFPA Hazard Codes: Health 1; Flammability 1; Reactivity 0; Protection B Ratings based on NPFA DISCLAIMER: Although the information and recommendations set forth herein (hereinafter Information ) are presented in good faith and believed to be correct as of the date hereof, NOV FluidControl, makes no representations as to the completeness or accuracy thereof. Information is supplied upon the condition that the person receiving this MSDS will make own determination as to its suitability for their intended purpose prior to use. Since the product is within the exclusive control of the user, it is the user s obligation to determine the conditions of safe use of this product. Such conditions should comply with all Federal Regulations concerning the Product. NO REPRESENTATIONS OR WARRANTIES, EITHER EXPRESS OR IMPLIED, OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER NATURE ARE MADE HERUNDER WITH RESPECT TO INFORMATION OR THE PRODUCT TO WHICH INFORMATION REFERS. For further information contact: NOV FluidControl 4310 N Sam Houston Parkway East Houston, Texas USA Office: (713) Fax: (713) Company website: D4A Rev02 Page 5 of 5