In accordance with Occupational Safety and Health Act (1970), Hazard Communication Standard 2012 (29 CFR ) (HazCom 2012) SAFETY DATA SHEET

Transcription

1 Section 1 - Product and Company Identification Product: Version #: Version #1 Date: May 15, 2015 CAS #: Non-Applicable Product Use: Mold Making and Casting Manufacturer/Supplier: Company Name: Alumilite Company Address: 315 E. North St. Kalamazoo, MI Emergency Telephone Number: Chemtrec GHS Classification Section 2 - Hazards Identification Health Environmental Physical Not Classified Not Classified Not Classified 2.2 GHS Signal Word, Hazard Statement, Symbol Pictograms by CLP/GHS: Pictograms by DPD: Signal Word: Hazard Statements Causes mild skin irritation and mild eye irritation. Precautionary Statements Wear appropriate protective gloves, protective spectacles, and the protection side. Wash hands well after handling. Avoid discharge into the environment. Section 3 - Composition / Information on Ingredients List of ingredients was submitted for review and none of the ingredients are hazardous substances. Section 4 First Aid Skin: Ingestion: Flush with large amounts of clean water for 15 minutes. If irritation persists, get medical attention. Remove paste from skin with dry cloth or towel, and wash exposed area with detergent. Do not induce vomiting! Do not give Liquids! Get medical attention immediately. Section 5 Fire Fighting Measures Extinguishing Media: Fire Fighting Instructions: Flash Point: Foam, dry chemical, or carbon dioxide. N/A >200 C (open cup) A Page 1 of 3

2 Section 6 Accidental Release Measures Contain the spill or leak. Scrape up with cardboard or rag and place in container. Can be burned in accordance with regulations. Section 7 Handling and Storage Storage: Avoid contact with eyes and prolonged or repeated skin contact. Keep container closed when not in use. Store in a cool place. Keep away from heat and flame. Section 8 Exposure Controls & Personal Protection Clothing: Respiration: Ventilation: Gloves, coveralls, apron, boots as necessary to prevent skin contact. Chemical goggles; also wear face shield if splashing hazard exists. Approved organic vapor mist respirator unless adequate local exhaust ventilation is provided or Exposure assessment demonstrates that exposures are within recommended exposure guidelines. Where concentrations are above recommended limits or are unknown, appropriate respiratory protection Should be worn. Follow OSHA respirator regulations (29 CFR ) and use NIOSH/MSHA approved respirators. Use local exhaust to control vapors/mists. Section 9 Physical & Chemical Properties Color: Form: Odor: Odor Intensity: Specific Gravity: Solubility: Milky Color Paste Slight Mild N/A None Section 10 Stability & Reactivity Stability: Unstable Incompatibility: Polymerization initiators including peroxides, strong base oxidizing agents, copper, copper alloys, carbon steel, iron. Hazardous Decomposition Products: Fumes produced when heated to decomposition may include carbon monoxide, carbon dioxide, oxides of nitrogen. Hazardous Polymerization: May occur. Conditions to Avoid: Storage >100F, exposure to light, loss of dissolved air, loss or polymerization inhibitors contamination with incompatible materials. Section 11 Toxicological Information Section 12 Ecological Information (Non-Mandatory) A Page 2 of 3

3 Section 13 Disposal Information (Non-Mandatory) Container Disposal: Incinerate or bury in a licensed facility. Do not discharge into waterways or sewer systems without proper authority. Steel drums must be emptied (as defined by RCRA, Section or state regulations that may be more stringent) and can be sent to a licensed drum reconditioner for reuse, a scrap metal dealer, or an approved landfill. Drums destined for a scrap dealer or landfill must be punctured or crushed to prevent reuse. Section 14 Transportation Information (Non-Mandatory) Not regulated by the Department of Transportation Section 15 Regulatory Information (Non-Mandatory) Hazardous Rating: No Data Available Section 16 Other Information No data available To the best of our knowledge, the information contained herein is accurate. However, Alumilite does not assume any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be handled with care. Although we have described herein all of the hazards to which we are currently aware, we cannot guarantee that these are the only hazards which exist. While the descriptions, designs, data, and information contained herein are presented in good faith and believed to be accurate, it is provided for your guidance only. Further, you expressly understand and agree that the descriptions, designs, data, and information furnished by Alumilite hereunder are given gratis and Alumilite assumes no obligation or liability for the description, designs, data, and information given or results obtained, all such being given and accepted at your risk. Date: May, 2015 Document Number: (A) Safety Data Sheet Provided By: Modern Testing Services, LLC 244 Liberty Street, Unit 1-2, Brockton, MA Tel: (508) Website: A Page 3 of 3

4 Section 1 - Product and Company Identification Product: Amazing Mold Putty, Mold Putty & Mold Putty 15 B Side Version #: Version #1 Date: May 15, 2015 CAS #: Non-Applicable Product Use: Mold Making and Casting Manufacturer/Supplier: Company Name: Alumilite Company Address: 315 E. North St. Kalamazoo, MI Emergency Telephone Number: Chemtrec GHS Classification Section 2 - Hazards Identification Health Environmental Physical Not Classified Not Classified Not Classified 2.2 GHS Signal Word, Hazard Statement, Symbol Pictograms by CLP/GHS: Pictograms by DPD: Signal Word: Hazard Statements Causes mild skin irritation and mild eye irritation. Precautionary Statements Wear appropriate protective gloves, protective spectacles, and the protection side. Wash hands well after handling. Avoid discharge into the environment. Section 3 - Composition / Information on Ingredients: List of ingredients was submitted for review and none of the ingredients are hazardous substances. Section 4 First Aid Skin: Ingestion: Flush with large amounts of clean water for 15 minutes. If irritation persists, get medical attention. Remove paste from skin with dry cloth or towel, and wash exposed area with detergent. Do not induce vomiting! Do not give Liquids! Get medical attention immediately. Section 5 Fire Fighting Measures Extinguishing Media: Fire Fighting Instructions: Flash Point: Foam, dry chemical, or carbon dioxide. N/A 94 C (open cup) Amazing Mold Putty, Mold Putty and Mold Putty 15 B Side B Page 1 of 3

5 Section 6 Accidental Release Measures Contain the spill or leak. Scrape up with cardboard or rag and place in container. In such a Case, pay attention to generation of hydrogen gas by contaminants. Can be burned in accordance with regulations. Section 7 Handling and Storage Storage: Avoid contact with eyes and prolonged or repeated skin contact. Keep container closed when not in use. Store in a cool place. Keep away from heat and flame. Do not lay the container on its side. Section 8 Exposure Controls & Personal Protection Clothing: Respiration: Ventilation: Other: Plastic film or rubber gloves, coveralls, apron, and boots as necessary to prevent skin contact. Safety glasses. Not required. Not required. Eyewash equipment. Section 9 Physical & Chemical Properties Color: Form: Odor: Odor Intensity: Specific Gravity: Solubility: Vapor Pressure: Yellow Paste None None 1.35 (at 25 C) Not soluble Negligible (at 25 C) Section 10 Stability & Reactivity Stability: Unstable. Conditions to Avoid: Avoid contact with acidic, basic, and oxidizing materials. Incompatibility: Acidic, basic, and oxidizing materials. Hazardous Decomposition Products: Flammable hydrogen gas. Hazardous Polymerization: Will not occur. Section 11 Toxicological Information Section 12 Ecological Information (Non-Mandatory) Section 13 Disposal Information (Non-Mandatory) Can be burned in accordance with regulations. Amazing Mold Putty, Mold Putty and Mold Putty 15 B Side B Page 2 of 3

6 Not regulated by the Department of Transportation. No data available Section 14 Transportation Information (Non-Mandatory) Section 15 Regulatory Information (Non-Mandatory) Section 16 Other Information To the best of our knowledge, the information contained herein is accurate. However, Alumilite does not assume any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be handled with care. Although we have described herein all of the hazards to which we are currently aware, we cannot guarantee that these are the only hazards which exist. While the descriptions, designs, data, and information contained herein are presented in good faith and believed to be accurate, it is provided for your guidance only. Further, you expressly understand and agree that the descriptions, designs, data, and information furnished by Alumilite hereunder are given gratis and Alumilite assumes no obligation or liability for the description, designs, data, and information given or results obtained, all such being given and accepted at your risk. Date: May, 2015 Document Number: (B) Safety Data Sheet Provided By: Modern Testing Services, LLC 244 Liberty Street, Unit 1-2, Brockton, MA Tel: (508) Website: Amazing Mold Putty, Mold Putty and Mold Putty 15 B Side B Page 3 of 3