FILTER HOUSINGS SLIM LINE PROFESSIONAL FILTER HOUSINGS SLIM LINE FILTER HOUSINGS

Transcription

1 SLIM LINE FILTER HOUSINGS #20 Opaque #10 Clear SLIM LINE FILTER HOUSINGS Slim Line filter housings are available in either reinforced polypropylene or clear Styrene- Acrylonitrile (SAN) in 5", 10" and 20" lengths. The black or blue reinforced polypropylene housing caps are available with 1/4", 3/8" or 1/2" NPT connections. Four bosses are molded into every cap for mounting purposes. They are equipped with a black, reinforced polypropylene cap and offer an optional pressure-relief button on the inlet side to relieve pressure inside the housing when changing filter cartridges. Slim Line filter housings are an excellent choice for low-flow applications and when space and chemical compatibility are primary concerns. Opaque Slim Line Filter Housings Molded from rugged reinforced polypropylene, Opaque Slim Line filter housings offer outstanding chemical compatibility and are ideal for use in a variety of low-flow applications. These applications include under-sink and countertop residential filtration, pre- and post-reverse osmosis filtration, recreational vehicle filtration, food service and humidifying systems. Clear Slim Line Filter Housings offer on-site examination of flow, performance, and cartridge life. They are also ideal for a variety of applications. #5 Clear #5 Opaque #10 Opaque Manufactured of clear Styrene- Acrylonitrile (SAN), the sumps are annealed to relieve stress, adding clarity and strength. PROFESSIONAL FILTER HOUSINGS

2 SLIM LINE The , , , , , , , , , ,158149, , , , and are Tested and Certified by NSF International to NSF/ANSI Standard 42 for material and structural integrity requirements. #5 Clear 7 3 8" x 4 5 8" (187 mm x 118 mm) 1/4" NPT 2 3 gpm ( Lpm) #10 Clear " x 4 5 8" (308 mm x 118 mm) 3/8" NPT 2 5 gpm ( Lpm) #5 Opaque 7" x 4 3 8" (178 mm x 111 mm) 1/4" NPT 2 3 gpm ( Lpm) #10 Opaque " x 4 3 8" (299 mm x 111 mm) 1/2" NPT 2 5 gpm ( Lpm) #20 Opaque " x 4 3 8" (556 mm x 111 mm) 1/2" NPT 2 5 gpm ( Lpm) Housing SAN (Clear) or Polypropylene (Opaque) Cap Reinforced Polypropylene Button Assembly 300-series Stainless Steel, EPDM, and Polypropylene O-Ring Maximum Temperature 125ºF (51.7ºC) Maximum Pressure 125 psi (8.62 bar) CAUTION: Protect against freezing to prevent cracking of the filter and water leakage. PROFESSIONAL FILTER HOUSINGS 2006 Pentair Filtration, Inc. Printed in USA MR

3 3G SLIM LINE FILTER HOUSINGS 3G SLIM LINE FILTER HOUSINGS TM Slim Line housings are the perfect choice for low-flow filtration applications. Their slim design and high chemical compatibility make them ideal for those challenging applications. Caps are manufactured from reinforced polypropylene in black, blue, and white. Standard NPT threaded and John Guest connections are available with 1/4-inch, 3/8-inch and 1/2-inch connections. Three different style caps add to the flexibility of these housings. The mounting boss cap features bosses molded in to the cap. This allows the housing to be mounted to a single bracket or a multiple housing bracket. The integral bracket cap does not require a separate bracket as the bracket is part of the cap. This feature saves valuable time during installation. Take the guesswork out of when to change your cartridge by using the meter mount cap. These gauges indicate when the cartridge is dirty and allow you to get the most out of your cartridges. Pressure relief buttons are another option with the Slim Line 3G housings. Placed on the inlet side, the pressure-relief button helps reduce the pressure in the housing when changing the cartridge. Housings are available with either clear or opaque sumps. The clear housings are manufactured of Styrene- Acrylonitrile (SAN) and are stress relieved through a special process for added strength and clarity. Clear housings offer on-site examination of the flow, cartridge life and performance. Opaque housings are molded from reinforced polypropylene and offer outstanding chemical compatibility. Typical applications for the 3G Slim Line housings include, but are not limited to, undersink residential filtration, pre- and post reverse osmosis systems, recreational vehicle filtration, and food service. PROFESSIONAL FILTER HOUSINGS * U.S. Patent No. D 455,194 S and D 456,486 S

4 * ** ** * Shown with differential gauge. Gauges are not performance tested or certified by NSF. ** Gauges sold seperately. Filter Housings Tested and Certified by NSF International to NSF/ANSI Standard 42 for material and structural integrity requirements. Housing Specifications and Performance Data Model 1/4-inch #10 3G Slim Line w/mb 1/4-inch #10 3G Slim Line w/ib 3/8-inch #10 3G Slim Line w/mb 3/8-inch #10 3G Slim Line w/ib 1/2-inch #10 3G Slim Line w/mb 1/2-inch #10 3G Slim Line w/ib 1/2-inch #10 3G Slim Line w/ib & MM Maximum Dimensions " x 4 3 4" (298 mm x 121 mm) " x 5 3 8" (340 mm x 137 mm) " x 4 3 4" (298 mm x 121 mm) " x 5 3 8" (340 mm x 137 mm) " x 4 3 4" (298 mm x 121 mm) " x 5 3 8" (340 mm x 137 mm) " x 5 3 8"* (340 mm x 137 mm) Initial P Flow Rate (gpm) 2 3 gpm ( L/min) 2 3 gpm ( L/min) 2 5 gpm ( L/min) 2 5 gpm ( L/min) 2 5 gpm ( L/min) 2 5 gpm ( L/min) 2 5 gpm ( L/min) MB = Mounting Bosses for MC-1A Bracket, 1B = Integral Bracket, MM = Meter Mount *Height does not include meter. Add inch for gauge and 1/2-inch for gauge. Housing Polypropylene (Opaque) or Styrene Acrylonitrile (Clear) Cap Reinforced Polypropylene Button Assembly O-Ring Maximum Temperature 125 F (51.7 C) 125 F (51.7 C) 125 F (51.7 C) 125 F (51.7 C) 125 F (51.7 C) 125 F (51.7 C) 125 F (51.7 C) Maximum Pressure 125 psi (8.62 bar) 125 psi (8.62 bar) 125 psi (8.62 bar) 125 psi (8.62 bar) 125 psi (8.62 bar) 125 psi (8.62 bar) 125 psi (8.62 bar) PROFESSIONAL FILTER HOUSINGS

5 STANDARD FILTER HOUSINGS #20 Opaque MB #10 Opaque MB STANDARD FILTER HOUSINGS Standard filter housings are manufactured of a durable polypropylene or clear FDAcompliant Styrene-Acrylonitrile (SAN). All are equipped with 3/4" NPT inlet and outlet ports. Standard filter housings are available in both 10" and 20" lengths and will accommodate a wide range of 2 1 2" to 2 7 8" diameter cartridges. The reinforced polypropylene cap and offers an optional pressure-relief button on the inlet side to relieve pressure inside the housing when changing filter cartridges. Reinforced polypropylene housings have excellent chemical resistance and are ideal for many residential, commercial and industrial applications. Clear sumps offer onsite examination of the cartridge. Opaque Standard Filter Housings are molded from rugged reinforced polypropylene. They offer outstanding chemical compatibility and are ideal for use in a variety of low-flow applications. These applications include under-sink and countertop residential filtration, preand post-reverse osmosis filtration, recreational vehicle filtration, food service and humidifying systems. Clear Standard Filter Housings offer on-site examination of flow, performance, and cartridge life. They are also ideal for a variety of applications. #10 Clear MB Manufactured of clear, Styrene- Acrylonitrile (SAN), the sumps are annealed to relieve stress, adding clarity and strength. PROFESSIONAL FILTER HOUSINGS

6 STANDARD The , , , , , , and are Tested and Certified by NSF International to NSF/ANSI Standard 42 for material and structural integrity requirements. #10 Opaque " x 5 1 8" (311 mm x 130 mm) 1 10 gpm ( Lpm) #10 Clear " x 5 1 4" (321 mm x 133 mm) 1 10 gpm ( Lpm) #20 Opaque " x 5 1 8" (568 mm x 130 mm) 1 10 gpm ( Lpm) Housing Polypropylene (Opaque) or Styrene Acrylonitrile (Clear) Cap Reinforced Polypropylene Button Assembly 300-series Stainless Steel, EPDM, and Polypropylene O-Ring Maximum Temperature 125ºF (51.7ºC) Maximum Pressure 125 psi (8.62 bar) CAUTION: Protect against freezing to prevent cracking of the filter and water leakage. PROFESSIONAL FILTER HOUSINGS 2006 Pentair Filtration, Inc. Printed in USA MR

7 VALVE-IN-HEAD FILTER HOUSINGS #20 Opaque VIH #10 Clear VIH VALVE-IN-HEAD FILTER HOUSINGS Valve-in-head (VIH) filter housings incorporate the same rugged design and application features as our Standard 3/4" NPT housings. The internal valve-in-head allows both inlet and outlet ports to be simultaneously shut-off with a half turn of the handle. This eliminates the need for external shut-off valves. Radial sealing o-rings and sealing surfaces are continuously cleaned each time the valve is used, ensuring leak-proof operation. Valve-in-head filter housings are available in both 10" and 20" lengths, and will accommodate a wide range of 2 3 8" to 2 7 8" diameter cartridges. The polypropylene caps feature pressure-relief button on the inlet side to relieve pressure inside the housing when changing filter cartridges. Opaque Valve-In-Head Filter Housings are molded from rugged reinforced polypropylene, Opaque Valve-In-Head filter housings offer outstanding chemical compatibility and are ideal for use in a variety of low-flow applications. These applications include undersink and countertop residential filtration, pre- and post-reverse osmosis filtration, recreational vehicle filtration, food service and humidifying systems. Clear Valve-In-Head Filter Housings offer on-site examination of flow, performance, and cartridge life. #10 Opaque VIH They are also ideal for a variety of applications. Manufactured of clear, FDAcompliant Styrene-Acrylonitrile (SAN), the sumps are annealed to relieve stress, adding clarity and strength. PROFESSIONAL FILTER HOUSINGS

8 VALVE-IN-HEAD The and are Tested and Certified by NSF International to NSF/ANSI Standard 42 for material and structural integrity requirements. #10 VIH " x 5 1 8" (318 mm x 130 mm) 4 8 gpm ( Lpm) #10 VIH Clear " x 5 1 4" (327 mm x 133 mm) 4 8 gpm ( Lpm) #20 VIH " x 5 1 8" (575 mm x 130 mm) 4 8 gpm ( Lpm) Housing Polypropylene (Opaque) or Styrene Acrylonitrile (Clear) Cap Reinforced Polypropylene Button Assembly 300-series Stainless Steel, EPDM, and Polypropylene Valve Parts Delrin O-Ring Maximum Temperature 125ºF (51.7ºC) Maximum Pressure 125 psi (8.62 bar) CAUTION: Protect against freezing to prevent cracking of the filter and water leakage. PROFESSIONAL FILTER HOUSINGS 2006 Pentair Filtration, Inc. Printed in USA MR

9 3G STANDARD FILTER HOUSINGS 3G STANDARD FILTER HOUSINGS We took our time tested industry standard and made it even better. We started from the ground up, utilizing our 35 years of experience, to create the unique and innovative 3G design. This patented* design features integral brackets, 20" clear housings, and caps for differential pressure gauges. The 3G housings accept standard double open end (DOE) and our Seal Safe o ring sealing cartridges. The Seal Safe o ring design offers enhanced cartridge sealing for critical cartridge applications. 3G Standard Filter Housings are manufactured from durable polypropylene or clear Styrene Acrylonitrile (SAN). Reinforced polypropylene housings have excellent chemical resistance and are ideal for many residential, commercial and industrial applications. Clear sumps are manufactured from FDA compliant Styrene Acrylonitrile (SAN). They offer on site examination of the cartridge and have excellent chemical compatibility. All are equipped with 3/4" NPT inlet and outlet ports. 3G Standard Filter Housings are available in 10" and 20" lengths and will accommodate a wide range of 2 1 4" to 3 1 8" diameter cartridges. PROFESSIONAL FILTER HOUSINGS * U.S. Patent No. D 455,194 S and D 456,486 S

10 3G SERIES * Approximate Net Pressure Drop psi (bar)* 7 (0.48) (0.41) 5 (0.35) (0.28) 3 (0.21) (0.14) (0.07) * (7.6) (15) (23) (30) (38) (45) (53) (60) (68) (76) Flow Rate gpm (lpm)* *Pressure drop and flow rate based on housing without cartridge. * Shown with differential gauge. Gauges sold seperately. 3G #10 Blue or Clear MB " x 5 3 8" (324 mm x 137 mm) 1 10 gpm ( Lpm) 3G #10 Blue or Clear MB " x 5 3 4" (337 mm x 146 mm) 1 10 gpm ( Lpm) 3G #20 Blue or Clear MB 23" x 5 3 8" (597 mm x 137 mm) 1 10 gpm ( Lpm) 3G #20 Blue or Clear IB/MM* " x 5 3 4" (597 mm x 146 mm) 1 10 gpm ( Lpm) Housing Polypropylene (Opaque) or Styrene Acrylonitrile (Clear) Cap Reinforced Polypropylene Button Assembly 300-series Stainless Steel, EPDM, and Polypropylene O-Ring Buna-N Maximum Temperature 125ºF (51.7ºC) Maximum Pressure 125 psi (8.62 bar) CAUTION: Protect against freezing to prevent cracking of the filter and water leakage. PROFESSIONAL FILTER HOUSINGS

11 BIG BLUE & BIG CLEAR FILTER HOUSINGS #20 Big Clear #20 Big Blue BIG BLUE & BIG CLEAR FILTER HOUSINGS #10 Big Blue #10 Big Clear Big Blue Filter Housings offer the versatility to meet all of your largecapacity filtration needs, including high-flow and heavy-sediment applications. The extra large housing allows for greater cartridge capacity, reducing the number of vessels required for high flow-rate applications. Sumps are constructed of durable reinforced polypropylene and are available in both 10" and 20" lengths. The high-flow polypropylene (HFPP) cap is available with 3/4", 1" or 1½" NPT inlet and outlet ports. The 1¼" internal port allows a greater volume of liquid to pass through the HFPP cap more rapidly. Big Blue housings are compatible with a broad range of chemicals and are available with or without a pressure relief button. They accept a wide variety of 4½" diameter cartridges. Big Clear Filter Housings offer on-site examination of flow, performance, and cartridge life and are ideal for a variety of applications. The blue polypropylene caps are available with an optional pressure-relief button on the inlet side to relieve pressure inside the housing when changing filter cartridges. PROFESSIONAL FILTER HOUSINGS

12 BIG BLUE IG CLEAR The , , , , , , , , , , , and Tested and Certified by NSF International to NSF/ANSI Standard 42 for material and structural integrity requirements. NOTE: The Big Clear Series of housings are not NSF component listed. #10 Big Blue 3/4" " x 7 1 4" (333 mm x 184 mm) 2 15 gpm ( Lpm) #10 Big Blue 1" " x 7 1 4" (333 mm x 184 mm) 1 15 gpm ( Lpm) #10 Big Blue 1 1 2" " x 7 1 4" (346 mm x 184 mm) 1 20 gpm ( Lpm) #20 Big Blue 3/4" " x 7 1 4" (594 mm x 184 mm) 2 15 gpm ( Lpm) #20 Big Blue 1" " x 7 1 4" (594 mm x 184 mm) 1 15 gpm ( Lpm) #20 Big Blue 1 1 2" " x 7 1 4" (606 mm x 184 mm) 1 20 gpm ( Lpm) #10 Big Clear 1"* 13½" x 7 1 8" (343 mm x 181 mm) 1 15 gpm ( Lpm) #20 Big Clear 1"* 23 ¾" x 7 1 8" (603 mm x 181 mm) 1 15 gpm ( Lpm) * Not Performance Tested or Certified by NSF. BIG CLEAR Housing Polypropylene Lexan (#10), Polycarbonate (#20) Cap Polypropylene (HFPP) Polypropylene (HFPP) Button Assembly 300-series Stainless Steel, EPDM, and Polypropylene O-Ring Buna-N Buna-N Maximum Temperature 100ºF (37.8ºC) 100ºF (37.8ºC) Maximum Pressure #10 Big Blue 100 psi (6.9 bar) #20 Big Blue 90 psi (6.2 bar) CAUTION: Protect against freezing to prevent cracking of the filter and water leakage. 300-series Stainless Steel, EPDM, and Polypropylene #10 Big Clear 100 psi (6.9 bar) #20 Big Clear 90 psi (6.2 bar) PROFESSIONAL FILTER HOUSINGS

13 HIGH TEMPERATURE FILTER HOUSINGS #20 Standard HIGH TEMPERATURE FILTER HOUSINGS Constructed of glass-reinforced nylon, High Temperature filter housings are an economical alternative to stainless and carbon steel housings. These 1/2" NPT housings can withstand temperatures up to a maximum of 160ºF (71.1ºC) while 3/4" housings can withstand temperatures up to 165ºF (73.9ºC). Excellent chemical compatibility makes High Temperature housings an ideal choice for a wide variety of industrial applications including those involving organic solvents, sea water, alcohol, petroleum and vegetable oils. They should not be used with ketones. A #241 o-ring provides dependable sealing. Both 10" and 20" lengths are available to accommodate flow rates up to 20 gpm (76 Lpm). #10 #10 Slim Line Standard PROFESSIONAL FILTER HOUSINGS

14 HIGH TEMPERATURE #10 Standard 3/4" " x 5 1 8" (308 mm x 130 mm) <1 8 gpm (< Lpm) #20 Standard 3/4" " x 5 1 8" (565 mm x 130 mm) <1 8 gpm (< Lpm) #10 Slim Line 1/2" " x 4 3 8" (298 mm x 111 mm) 5 8 gpm (< Lpm) Housing Cap Glass-Reinforced Nylon Glass-Reinforced Nylon O-Ring Slim Line Housings Viton Standard Housings Silicone Maximum Temperature 1/2" Housing 160ºF (71.1ºC) 3/4" Housing 165ºF (73.9ºC) Maximum Pressure 125 psi (8.62 bar) CAUTION: Protect against freezing to prevent cracking of the filter and water leakage. PROFESSIONAL FILTER HOUSINGS 2009 Pentair Residential Filtration, LLC FE

15 RO MEMBRANE HOUSING RO MEMBRANE HOUSING 12" with 90º Outlet The PENTEK RO Membrane Housing is manufactured in the U.S.A. from a high-quality, FDAapproved polypropylene. This component is NSF listed and will accommodate most standard 12" membrane elements. Both the ribbed cap and the housing are one-piece injection molded parts, requiring no solvents or glues to be used in the manufacturing process. The ribbed cap incorporates acme square threads and two o-rings to ensure a leak-proof seal. The RO Membrane Housings have a straight inlet and are equipped with (2) 90º outlets. The 90º outlets eliminate the need for additional elbows. All ports have standard 1/8 NPT threads. PROFESSIONAL FILTER HOUSINGS

16 RO MEMBRANE Housing Reinforced Polypropylene Finish Reinforced Polypropylene O-Ring EPDM Maximum Temperature Maximum Pressure 125 psi (8.62 bar) CAUTION: PROFESSIONAL FILTER HOUSINGS

17 MPST-1.5 STAINLESS STEEL FILTER HOUSING MPST-1.5 Multi-Purpose Stainless Steel Filter Housing MPST-1.5 The PENTEK MPST-1.5 multi-purpose stainless steel filter housing is designed to accept either a inch x 20-inch double open end (DOE) cartridge or a PENTEK #420 bag filter. The housing comes standard as a cartridge filter housing, but the optional bag filter kit quickly converts it to a bag filter housing. The MPST-1.5 housing is constructed of 304 stainless steel and powder-coated for a professional finish. This versatile housing is supplied with inch side inlet and bottom outlet ports, adjustable legs, drainage port and multiple gauge ports to easily adapt to any installation. Applications include high temperature (250 F), high pressure (150 psi), and flow rates up to 50 gpm. Ideal for reduction of sediment and chlorine taste in whole house or small business applications, these housings can also be used in most water treatment, food processing and general filtration applications. FEATURES BENEFITS 1 2 APPLICATIONS PROFESSIONAL FILTER HOUSINGS

18 MPST-1.5 Multi-Purpose Stainless Steel Filter Housing Cartridge and Bag Options Model Material Micron Rating Recommended Sediment Cartridges: DGD Polypropylene 25 to 1 DGD Polypropylene 50 to 5 Polypropylene Cellulose Polyester 1 Cellulose Polyester 5 Cellulose Polyester 20 Cellulose Polyester 50 Cellulose 20 Recommended Carbon Cartridges: Pleated Carbon 10 Granular Carbon Recommended Specialty Cartridge: Oil Adsorbing NR Model Material Micron Rating Recommended Filter Bags: Polypropylene Felt 1 Polypropylene Felt 5 Polypropylene Felt 10 Polypropylene Felt 25 Polypropylene Felt 50 Polypropylene Felt 100 Polypropylene Felt 200 Polypro High Efficiency 1 Polypro High Efficiency 5 Polypro High Efficiency 25 Polypro High Efficiency 50 Polypro High Efficiency 100 Nylon Monofilament 50 Nylon Monofilament 100 Nylon Monofilament 200 Nylon Monofilament 250 Nylon Monofilament 400 Nylon Monofilament 600 Nylon Monofilament 800 Housing Specifications and Performance Data Model MPST-1.5 Materials of Construction Housing Finish Sealing Gasket Maximum Flow Rate** 304 Stainless Steel Epoxy 50 gpm ) NOTE: Maximum cartridge diameter inches (12 mm) WARNING: If pressure exceeds 150 psi (10.34 bar) at any time, a pressure regulator must be used. Do not use water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. CAUTION: Protect against freezing to prevent cracking of the filter and water leakage. Dimensions Height x O.A. Dia* " x 6 3 8" NOTE: Bag filter conversion kit (243111) sold separately. *NOTE: Will not accept model GAC 20BB, BBF1-20BB, WS-20BB or CRFC-20BB cartridges. *Height does not include stand. ** Flow rate listed for housing without cartridge. Check cartridge specifications for cartridge flow rates. NOTE: Not recommended for applications with TDS or chlorides >1000 ppm and/or ph <5.0. Use of this product in these conditions will void the limited warranty. Consult factory for product modifications for these conditions. Pipe Size (NPT) 1 1 2" (38.1 mm) Maximum Temperature 250 ºF (121 ºC) Maximum Pressure 150 psi (10.34 bar) Customize Your Housing * * * Gauges sold separately Needle differential pressure gauge Needle points to international standard colors to determine when cartridge should be changed. Green (clean) 0-6 psid; Yellow (change) 6-9 psid; Red (dirty) 9-12 psid. Color change differential pressure gauge Green and red colors indicate when cartridge should be changed. Green (clean) 0-7 psid; Red (change) 7-10 psid. PROFESSIONAL FILTER HOUSINGS 2007 Pentair Filtration, Inc a JE07

19 ST SERIES STAINLESS STEEL FILTER HOUSINGS ST SERIES STAINLESS STEEL FILTER HOUSINGS ST-1 ST-3 ST-2 ST Series stainless steel filter housings effectively provide heavy-duty filtration for smaller filtration systems and point-of-use applications. Supplying flow rates of up to 20 gpm (76 Lpm), at a maximum water temperature of 300ºF (149ºC), ST Series housings are ideal for hot water and highpressure applications not suited for plastic housings. The brushed 304 stainless steel sumps are available with either a pipe plug or pet-cock in the bottom for draining. Heads are manufactured from nickel-plated cast-brass. ST Series housings are easy to install and maintain. They are compatible with a complete range of filter cartridges, adding to their versatility. PROFESSIONAL FILTER HOUSINGS

20 ST SERIES ST " x 4 1 8" (327 mm x 105 mm) 10 gpm (38 Lpm) 250 psi (17.2 bar) ST " x 4 1 8" (578 mm x 105 mm) 15 gpm (57 Lpm) 250 psi (17.2 bar) ST " x 4 1 8" (822 mm x 105 mm) 20 gpm (76 Lpm) 250 psi (17.2 bar) Housing Head Maximum Temperature 300ºF (149ºC) Pipe Size Sealing Gaskets WARNING: For drinking water applications, do not use with water that microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. CAUTION: Protect against freezing to prevent cracking of the filter and water leakage. NOTE: Not recommended for applications with TDS or chlorides >1000 ppm and/or ph <5.0. Use of this product in these conditions will void the limited warranty. Consult factory for product modifications for these conditions. PROFESSIONAL FILTER HOUSINGS

21 ST-BC SERIES STAINLESS STEEL FILTER HOUSINGS ST-BC-16 ST-BC-12 ST-BC-4 ST-BC SERIES STAINLESS STEEL FILTER HOUSINGS ST-BC Series stainless steel filter housings offer a variety of solutions for your large-scale, heavy-duty filtration needs. Simple to install and maintain, these housings are ideal for schools, restaurants, farms, institutions and industrial use. Holding from 4 to 20 cartridges, ST-BC Series housings provide flow rates from gpm ( Lpm). Housings are constructed of 304 stainless steel with a gray-silver epoxy finish. They include drains on both the clean and dirty sides of the sump. ST-BC Series housings are compatible with a complete range of filter cartridges, adding to their versatility. ST-BC-20 ST-BC-8 PROFESSIONAL FILTER HOUSINGS

22 ST-BC SERIES ST-BC-4 28 gpm (106 Lpm) " x 10" (489 mm x 254 mm) 4 x 1 3" (76 mm) 9 3 4" or 10" (248 mm or 254 mm) 2" (50.8 mm) ST-BC-8 56 gpm (212 Lpm) 29" x 10" (737 mm x 254 mm) 4 x 2 3" (76 mm) 9 3 4" or 10" (248 mm or 254 mm) 2" (50.8 mm) ST-BC gpm (318 Lpm) " x 10" (1010 mm x 254 mm) 4 x 3 3" (76 mm) 9 3 4" or 10" (248 mm or 254 mm) 2" (50.8 mm) ST-BC gpm (416 Lpm) " x 10" (1264 mm x 254 mm) 4 x 4 3" (76 mm) 9 3 4" or 10" (248 mm or 254 mm) 2" (50.8 mm) ST-BC gpm (473 Lpm) " x 10" (1264 mm x 254 mm) 5 x " (64 mm) 9 3 4" or 10" (248 mm or 254 mm) 2" (50.8 mm) Housing Finish Maximum Temperature Maximum Pressure Pipe Size Sealing Gasket Brushed 304 Stainless Steel Epoxy 125 psi (8.62 bar) Buna-N ** Number of cartridges refers to the number of means that 9 3 4" (248 mm) cartridges are configured four around and two high. NOTE: WARNING: before or after the system. CAUTION: NOTE: modifications for these conditions. PROFESSIONAL FILTER HOUSINGS

23 BAG VESSEL FILTER ASSEMBLIES PBH-410 (Shown with bag vessel stand)* BAG VESSEL FILTER ASSEMBLIES PENTEK's standard bag vessel assemblies keep your system on stream longer by reducing bag filter change time. They are made of lightweight corrosion resistant polypropylene to give you all the strength you need without the weight. Install as a duplex system for totally uninterrupted flow rates. All PBH Series vessels come complete with gauge, wrench and 3/8" drain valve. The single large Acme thread closure ensures quick opening and positive sealing. Filter bags are available in polypropylene felt, absolute-rated high-efficiency polypropylene and nylon monofilament mesh ideal for filtering and straining applications from 1 to 800 microns. Molded from rugged reinforced polypropylene, Bag filter housings offer outstanding chemical compatibility and are ideal for use in a variety of low-flow applications. These applications include residential prefiltration, food service along with commercial and industrial applications for water filtration and chemical filtration. They are equipped with a black, reinforced polypropylene cap. *Bag vessel stand sold separately. PBH-420 PROFESSIONAL FILTER HOUSINGS

24 BAG VESSEL PBH (1" NPT) " x 7 1 4" (333 mm x 184 mm) 1 15 gpm ( Lpm) 100 psi (6.9 bar) PBH (1 1 2" NPT) " x 7 1 4" (346 mm x 184 mm) 1 15 gpm ( Lpm) 100 psi (6.9 bar) PBH (1" NPT) " x 7 1 4" (594 mm x 184 mm) 1 15 gpm ( Lpm) 90 psi (6.2 bar) PBH (1 1 2" NPT) " x 7 1 4" (606 mm x 184 mm) 1 15 gpm ( Lpm) 90 psi (6.2 bar) 1 4" (102 mm x 210 mm) bag. Dimensions allow for 1" (25 mm) overlap on basket. 1 2" (102 mm x 470 mm) bag. Dimensions allow for 1" (25 mm) overlap on basket. Housing Cap Gauge Vent Plug Drain Plug Ball Valve Basket O-Ring and Gaskets Maximum Temperature Polypropylene Polypropylene Bismuth Brass (lead-free) Polypropylene High Density Polypropylene PVC/Buna-N Seals Polypropylene Buna-N 100ºF (37.8ºC) NOTE: Many standard bags with rings may be used in these vessels. Refer to PENTEK's bag filter specifications sheet for 1 to 200 micron quick-install bags. PROFESSIONAL FILTER HOUSINGS 2006 Pentair Filtration, Inc. Printed in USA MR

25 Traditional In-line Filter Series traditional IN-LINE filter SERIES Provide bad taste & odor and chlorine taste & odor reduction Injection molded and pressure rated to 125 psi All in-line filters include a pre- and post-filter IC-101L TS-101L PENTEK Traditional In-Line filters feature coconut shell, granular activated carbon, and are designed to reduce unwanted taste, odor and chlorine taste and odor. The TS-101L contains a combination of GAC and polyphosphate crystals to inhibit lime/scale build-up. All Traditional In-Line filters include a durable, injection molded polypropylene body and cap, preand post-filter. They are pressure rated to 125 psi. and come standard with 1/4" NPT connections. Traditional In-Line filters are an ideal choice for post-ro, undersink, ice-maker and food service applications. Contact factory regarding availability of other sizes and media.

26 traditional In-line SERIES Disposable In-Line Filters The IC-101L and TS-101L are Tested and Certified by NSF International. Specifications and Performance Data Model Media Maximum Dimensions Estimated Life Flow Rate IC-101L Coconut Shell GAC (17 cu. in.) 2" x " (51 mm x 270 mm) 2500 gallons (9460L) 0.75 gpm (2.8 Lpm) TS-101L Phosphate/GAC (16 cu. in.) 2" x " (51 mm x 270 mm) 1700 gallons (6450L) 0.75 gpm (2.8 Lpm) Materials of Construction Body Cap Pre-Filter and Post-Filter Carbon Maximum Temperature Operating Pressure Polypropylene Polypropylene Polypropylene Coconut Shell GAC 100ºF (37.8ºC) 125 psi (8.62 bar) WARNING: For drinking water applications, do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. NOTE: Cartridges will contain a very small amount of fines (very fine powder) and new cartridges, after installation, should be flushed with sufficient water to remove all traces of fines from your water system before use. Each time you use your filtered water tap for drinking or cooking purposes, it is recommended that you run (flush) the tap for at least 10 seconds prior to using the water. This is particularly important if the water tap has not been used daily. CAUTION: Protect against freezing to prevent cracking of the filter and water leakage. 502 Indiana Avenue P.O. Box 1047 Sheboygan, Wisconsin Customer Service: Fax: supportspecialist@pentekfiltration.com International: Fax: international@pentekfiltration.com 2006 Pentair Filtration, Inc. Printed in USA MR

27 QUICK-CHANGE FILTRATION SYSTEMS QUICK-CHANGE FILTRATION SYSTEMS Easy to install, easy filter change Unique cover for single unit for a more appealing look Reversible metal brackets for 1, 2 or 3 cartridges 1/4-inch or 3/8-inch John Guest push-fit connections available 1/4-inch compression connections available for flex hose connections Seven cartridge models to choose from to meet specific application needs The Twin and Triple systems are not performance tested or certified by NSF. PENTEK Quick Change Filtration Systems are designed for easy installation and cartridge change. 1/4-inch or 3/8-inch push fittings, as well as 1/4-inch compression fittings, on the inlet and outlet sides of the filter head allow effortless installation. Many single systems are NSF Certified. The cartridge filter is easily changed with a quarter-turn of the filter. Water is automatically shut off during the change of the filter through the auto shut-off feature built into the filter head. This feature eliminates the need for additional shut-off valves to and from the filter system. The PENTEK quick-change filter system offers several cartridge options to meet the demands of varying water conditions. The granular activated carbon cartridge offers extended chlorine taste and odor performance with low pressure drop.* The EP carbon block filter offers superior chlorine taste and odor performance with 5 micron sediment reduction.* The CBR carbon block cartridge has enhanced performance capabilities for chlorine taste & odor, cyst, lead, atrazine and lindane reduction. The new cartridges include carbon/ phosphate cartridge, chloramine reduction cartridge, sediment only cartridge, a high performance 1- micron carbon block cartridge, and the soon to be released membrane filter cartridge for bacteria and virus reduction.* PENTEK's quick-change filter system applications include: under-sink drinking water refrigerator/icemaker pre/post RO membrane vending machine ice machine coffee machine other OEM applications * Not performance tested or certified by NSF. *Not Performance Tested or Certified by NSF.

28 QUICK-CHANGE Filtration Systems * * Shown with optional designer cover The Twin and Triple systems are Not Performance Tested or Certified by NSF. Model QC10-CBR Cartridge Color Claims Filter Life chlorine taste & odor, sediment, White lead, atrazine, lindane, cyst and 500 gallons (1890 L) turbidity QC10-EP White chlorine taste & odor 1,500 gallons (5670 L) QC10-GAC Blue chlorine taste & odor 2,500 gallons (9460 L) QC10-TSGAC Blue chlorine taste & odor with phosphate crystals 1,700 gallons (6435 L) QC10-SED1 White sediment QC10-CGAC QC10-CB1 Blue White chloramine taste & odor and chlorine taste & odor chlorine taste & odor and sediment *Filter life based on chlorine reduction as tested by Pentair Filtration, Inc. Not Performance Tested or Certified by NSF. 500 gal. (1890 L) chloramine* 10,000 gal. (37850 L) chlorine* 10,000 gallons (37850 L) Flow Rate 0.5 gpm (1.9 L/min) 0.5 gpm (1.9 L/min) 0.75 gpm (2.8 L/min) 0.75 gpm (2.8 L/min) 0.6 gpm (2.3 L/min) 0.6 gpm (2.3 L/min) 0.6 gpm (2.3 L/min) Micron Rating 1/4-inch Threaded 1/4-inch JG Push fit 3/8-inch JG Push fit The QC10-CBR is Tested and Certified by NSF/ANSI to Standard 42 for the reduction of Chlorine Taste & Odor and Particulate Class I. Standard 53 Atrazine, Cyst, Lead, Lindane and Turbidity. The QC10-SED1 is Tested and Certified by NSF International to NSF/ANSI Standard 42 for the aesthetic reduction of Particulate Class 1. QC10-EP is Tested and Certified by NSF/ANSI to Standard 42 for the reduction of Chlorine Taste & Odor. The QC10-CB1 is Tested and Certified by NSF International to NSF/ANSI Standard 42 for the aesthetic reduction of Chlorine Taste & Odor and Particulate Class 1. QC10-GAC and QC10-TSGAC is Tested and Certified by NSF/ANSI to Standard 42 for the reduction of Chlorine Taste & Odor. WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. CAUTION: Protect against freezing to prevent cracking of the filter housing and water leakage. Note: Cartridge will contain a very small amount of carbon fines (a very fine black powder). After installation and before using the water follow the instructions for flushing the cartridge to remove fines. U.S. Patent Numbers 5,976,432 and 5,823, Indiana Avenue P.O. Box 1047 Sheboygan, Wisconsin Customer Service: Fax: supportspecialist@pentekfiltration.com International: Fax: international@pentekfiltration.com 2006 Pentair Filtration, Inc. Printed in USA AU

29 Under-Sink DRINKING WATER Systems RO-3500 UNDER-SINK DRINKING WATER SYSTEMS US-1000 & US-1500 Chemical/Lead Systems AS-301E Arsenic Reduction System* RO-3000 & RO-3500 Reverse Osmosis Systems US-1500 AS-301E PENTEK offers five systems suitable for under-sink, point-ofuse installation. These units offer a variety of contaminant reduction capabilities. The US-1000 and US-1500 Chemical/Lead Systems are NSF certified to reduce 43 different VOCs, lead, cysts, mercury, asbestos and chlorine taste & odor. Both systems come complete with cartridges, a long reach faucet, and installation hardware. The US-1500 features an electronic monitor for filter replacement. The US-1000 features MTBE reduction. The AS-301E Arsenic Reduction System reduces Arsenic III & V and chlorine taste & odor, a mechanical meter and comes complete with full hardware kit and faucet.* The RO-3000 and RO-3500 Reverse Osmosis systems offer the finest level of water filtration available filtering particles as small as 1/1000 of a micron. These systems are NSF certified to reduce salts, dissolved minerals and bad taste & odor and are designed for chlorinated or non-chlorinated water. The RO-3000 and RO-3500 each produce up to 7.6 gallons of top quality water per day, depending on your operating conditions. The RO-3500 features an electronic water quality monitor to indicate when to change the RO membrane. Both systems come complete with cartridges, a long reach faucet, and installation hardware. * Not performance tested or certified by NSF.

30 UNDERSINK DRINKING WATER SYSTEMS System Specifications Model Claims Maximum Dimensions US-1000 US-1500 AS-301E RO-3000 RO-3500 Bad Taste & Odor, Chlorine Taste & Odor, Sediment, Asbestos, Cyst, Lead, Mercury, MTBE, Turbidity, VOC Bad Taste & Odor, Chlorine Taste & Odor, Sediment, Asbestos, Cyst, Lead, Mercury, Turbidity, VOC 15" x 11" x 6.5" (381mm x 279mm x 165mm) 15" x 11" x 6.5" (381mm x 279mm x 165mm) Bad Taste & Odor, Chlorine Taste & Odor, Sediment, Arsenic III, Arsenic V " x 5 1 4" x 14" (394mm x 133mm x 356mm) Bad Taste & Odor, Chlorine Taste & Odor, Copper, Cyst, Fluoride, Lead, Selenium, Dissolved Minerals & Salts, Turbidity Chlorine Taste & Odor, Pentavalent Arsenic, Barium, Cadmium, Copper, Hexavalent & Trivalent Chromium, Cyst, Fluoride, Lead, Nitrate/Nitrite, Radium 226/228, Selenium, Dissolved Minerals & Salts, Turbidity " x 4 3 4" x " system (349mm x 120mm x 324mm) " x " x " tank (286mm x 286mm x 425mm) " x 4 3 4" x " system (349mm x 120mm x 324mm) " x " x " tank (286mm x 286mm x 425mm) Pressure Range Filter Life/ Daily Capacity psi 500 gallons psi 1000 gallons psi 1000 gallons psi 7.6 gallons/day psi 7.6 gallons/day Based on manufacturer's internal testing. Replacement Parts Model Description Part Number Fits P-250 Cartridge Set US-1500 P-250A Cartridge Set US-1000 AS-CK Cartridge Set AS-301E ROM-230T Thin Film Membrane RO-3000 ROM-230TN Thin Film Membrane RO-3500 ROR RO Replacement Cartridge Set RO-3000, RO-3500 SW-2 Spanner Wrench AS-301E SW-5 Spanner Wrench US-1000, US-1500, RO-3000, RO-3500 FT-20LR Faucet US-1000, US-1500 Auto Shut-Off Valve RO-3000, RO-3500 The US-1000 is Tested and Certified by NSF/ANSI to Standard 42 for the reduction of Chlorine Taste & Odor and Particulate Class I. Standard 53 Asbestos, Cyst, Lead, Mercury, MTBE, Turbidity and VOC. The RO-3000 is Tested and Certified by NSF/ANSI to Standard 58 for the reduction of Copper, Cyst, Fluoride, Lead, Selenium, TDS and Turbidity. The US-1500 is Tested and Certified by NSF/ANSI to Standard 42 for the reduction of Chlorine Taste & Odor and Particulate Class I. Standard 53 Asbestos, Cyst, Lead, Mercury, Turbidity and VOC. The RO-3500 is Tested and Certified by NSF/ANSI to Standard 58 for the reduction of Pentavalent Arsenic, Barium, Cadmium, Copper, Hexavalent & Trivalent Chromium, Cyst, Fluoride, Lead, Nitrate/Nitrite, Radium 226/228, Selenium, TDS and Turbidity. 502 Indiana Avenue P.O. Box 1047 Sheboygan, Wisconsin Customer Service: Fax: supportspecialist@pentekfiltration.com International: Fax: international@pentekfiltration.com 2006 Pentair Filtration, Inc. Printed in USA AU

31 BFS/BBFS SERIES BASIC FILTRATION SYSTEMS BBFS-222 BFS/BBFS SERIES BASIC FILTRATION SYSTEMS BFS and BBFS Basic Filtration Systems consist of either two or three filter housings, which are mounted in series, a wall-mounting bracket and hardware. The BFS-201 features two 3/8" NPT low-profile Slim Line housings in series for installations where space is limited. The BBFS systems consist of a series of large-capacity 1" NPT #20 Big Blue housings allowing for greater cartridge capacities and higher flow rates. All systems are equipped with a pressure relief button to relieve housing pressure during cartridge changes, and are shipped completely pre-assembled, saving valuable installation time. All filter housings are manufactured of a durable polypropylene, have excellent chemical resistance and are ideal for many residential, commercial and industrial applications. BFS-201 BBFS-22 PROFESSIONAL FILTRATION SYSTEMS

32 BFS/BBFS SERIES Whole House Filtration to Reduce: Deionization Step-down Filtration Rust Particles Coalescing Circulating Baths Iron (insoluable) Combination Plating Sediment Sediment/Rust Particles Batch Treatments Bad Taste & Odor Bad Taste & Odor Color Reduction Chlorine Taste & Odor Duplexing Organic Reduction Cooling Towers Pre RO Filtration Duplexing BFS-201 BBFS-22 BBFS " x 5 1 4" x 14" (267 mm x 133 mm x 356 mm) " x 8 1 2" x " (388 mm x 216 mm x 673 mm) " x 8 1 2" x " (591 mm x 216 mm x 673 mm) * Actual flow rate may vary and is dependent on the cartridge used. Cap Polypropylene Housing Polypropylene Bracket Powder Coated Carbon Steel O-Rings Buna-N Maximum Temperature 100ºF (37.8ºC) 125 psi (8.62 bar) up to 10 gpm (37.9 Lpm) 2 3/8" Slim Line 90 psi (6.2 bar) up to 40 gpm (151.4 Lpm) 2 1" #20 Big Blue 90 psi (6.2 bar) up to 40 gpm (151.4 Lpm) 3 1" #20 Big Blue NOTE: 20" (508 mm) Big Blue sumps are interchangeable with 10" (254 mm) Big Blue sumps. NOTE: Big Blue is a registered trademark of Pentair Water Treatment. WARNING: For drinking water applications, do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. CAUTION: Protect against freezing to prevent cracking of the filter and water leakage. PROFESSIONAL FILTRATION SYSTEMS 2006 Pentair Filtration, Inc. Printed in USA MR

33 UV Series Ultraviolet systems UVBB UV UV SERIES ULTRAVIOLET SYSTEMS High-intensity UV output for supplemental microbiological control in drinking or process water Positive alternative to environmentally harmful chemicals Available in three different sizes and two different voltages UV UVS The UVS-110, UV-110, UV-120 and UVBB Ultraviolet Systems are effective at protecting potable drinking water sources from occasional intrusion of microbiological contamination. This positive alternative to environmentally harmful chemicals uses ultraviolet light to control microbes. A germicidal dose of ultraviolet light (16,000 microwattsec per square centimeter) at a wavelength of 254 nanometers, disrupts the microbes reproductive process. All UV Series systems are constructed with a durable polypropylene housing; a quartz sleeve to protect the lamp and provide maximum UV transmittance; a UL-listed, voltage regulated control module, mounting bracket and hardware. UV-120 and UVBB models are equipped with a stainless steel insert sleeve to provide increased durability and maximize microbe reduction. UVS-110 and UV-110 systems are equipped with a CBU-10 carbon block cartridge to provide protection against Cryptosporidium and Giardia cysts and assuring maximum UV transmittance through the water by reducing turbidity. UV Series ultraviolet systems are available in two sizes: 120 volt, 60 hertz; and 220/240 volt, 50 hertz. System flow rate range from 1-15 gpm ( L/min).

34 UV SERIES Ultraviolet Systems Minimum Dose:* 16 mj/cm 2 (16,000 microwatt-sec per cm 2 ) Models UVS-110-1, UVS-110-2, UV and UV incorporate a carbon block cartridge (CBU-10) that surrounds the quartz tube. This cartridge provides prefiltration that assures maximum transmittance of UV light through the water and reduction of cysts such as Cryptosporidium and Giardia. NOTE: Carbon block prefilters or other fine filtration can be plumbed in separately to provide this function for models UV-120 and UVBB-120. *Determined by: LAMP INTENSITY (microwatts) X TIME OF EXPOSURE IN REACTOR CHAMBER (sec) SURFACE AREA OF REACTOR CHAMBER (cm 2 ) = microwatt sec/cm 2 = mj/cm 2 /1000 Germicidal Sun Tanning X-Ray Vacuum UV Short Wave UV-C Middle Wave UV-B Long Wave UV-A Visible Light PENTEK UV Nanometers System Specifications and Performance Data Model Dimensions Voltage Hertz Recommended Flow Rates Maximum Operating Pressure UVS-110-2* 5 1 2" x " (140 mm x 394 mm) gpm (3.8 Lpm) 65 psi (4.5 bar) UV-110-1* 5 1 2" x " (140 mm x 394 mm) gpm (7.6 Lpm) 65 psi (4.5 bar) UV-110-2* 5 1 2" x " (140 mm x 394 mm) gpm (7.6 Lpm) 65 psi (4.5 bar) UV " x " (140 mm x 648 mm) gpm (30.3 Lpm) 65 psi (4.5 bar) UV " x " (140 mm x 648 mm) gpm (30.3 Lpm) 65 psi (4.5 bar) UVBB " x 29" (178 mm x 737 mm) gpm (56.8 Lpm) 65 psi (4.5 bar) UVBB " x 29" (178 mm x 737 mm) gpm (56.8 Lpm) 65 psi (4.5 bar) * Supplied with a carbon block filter cartridge which reduces sediment, bad taste and odor, Cryptosporidium and Giardia cysts. For export sale only. Materials of Construction Housing Polypropylene Cap Polypropylene UV Sleeve Quartz O-Rings Buna-N Temperature Rating ºF ( ºC) Reaction Chamber Stainless Steel (20" models only) WARNING: Do not use where the water is microbiologically unsafe or with water of unknown quality without adequate disinfection before or after the system. EPA Est. No: WI Indiana Avenue P.O. Box 1047 Sheboygan, Wisconsin Customer Service: Fax: supportspecialist@pentekfiltration.com International: Fax: international@pentekfiltration.com 2006 Pentair Filtration, Inc. Printed in USA MR

35 FRESHPOINT ULTRAFILTRATION SYSTEM FRESHPOINT ULTRAFILTRATION SYSTEM Designed for cyst reduction, turbidity, and fine sediment filtration applications > 98% reduction of micron (25 nanometer) particles* > 99.99% (> 4 Log) reduction of micron (65 nanometer) particles* The PENTEK FreshPoint Ultrafiltration System provides complete point-of-entry (POE) filtration proven to reduce turbidity, particulates and cysts for safer, cleaner water at every tap. The system employs hollow-fiber Ultrafiltration membrane technology to filter impurities as small as microns. To maximize membrane capacity and service life, a metered flushing cycle is controlled using an advanced controller and high-performance turbine meter. The self-cleaning forward and back-flush cycles are initiated when the programmed capacity of the membrane is reached. During the backwash, flow is reversed and particles are ejected from the pores of the membrane and flushed to drain. In the forward- Forward-flush and back-flush cleaning cycles provide extended filter life in a wide range of applications Proprietary hollow-fiber ultrafiltration membrane Professional-grade housing, controller and flush valve flush cycle, service water passes through the capillaries at a high speed, scouring particles from the membrane surface and rinsing them from the system. Since power is only required to flush the system, outages and interruptions will not jeopardize the integrity of membrane or its ability to provide safer, cleaner water. The advanced electronic controller provides a programmable day override which allows the unit to flush every day with fresh water when the system is not in use. Critical system diagnostics, including totalized flow, instantaneous flow rate, and previous day s water usage, are available to optimize flushing cycles and monitor performance. Metered self-cleaning cycle flushes only when needed Day override feature flushes module daily with fresh water when system is not in use Peak flow rates up to 10 gpm (2271 L/h) The new high performance industrial stainless steel housing is pressure rated to 300 PSI. The new housing includes one piece endcaps with robust o-ring seals, all plumbing connection points, as well as, locking bars which allow for easier installation and service while minimizing the potential for leakage. In addition, test ports/pressure taps are built into the endcaps to allow for easier integrity testing to ensure your membrane fibers are intact. The system can be applied to solve known water problems including high turbidity, suspended solids, and certain microbiological contaminants. It can also serve as a flushable prefilter to extend the life of media filters downstream. PROFESSIONAL FILTRATION SYSTEMS This product is not certified as a microbiological purifier and should not be applied as a stand-alone disinfection solution for microbiologically unsafe water. * Performance based on MS-2 (25 nm) and PRD-1 (65 nm) virus particle tests. Data available upon request. Safe, Clean Water

36 ULTRAFILTRATION FreshPoint Advantages of FreshPoint Filter Technology ET Electronic Metered Controller System Specifications and Performance Data Membrane Material Polyethersulfone, modified (PESM) Pore Size micron (nominal) micron (absolute) Molecular Weight Cut Off (MWCO) kd Active Membrane Surface 51 sq. ft. Service Flow 15 psi drop Controller 6.23 gpm to 10 gpm (1,416 L/h to 2,271 L/H Electrical Rating 50/60 Hz Forward Flush Cycle 1-99 minutes Metered Volume gallons Meter Accuracy 1-50 gpm +/- 5% System Inlet/Outlet 3/4-inch NPT Pentair Water Solutions for Complete POE Treatment Pressurized Retention Tank FreshPoint Ultrafiltration System NOTE: This setup is used for most applications. Whole House Carbon Filter Flow Softener Control Valve Whole House Sediment Filter Polyglass Media Tank PROFESSIONAL FILTRATION SYSTEMS

37 POINT-OF-USE Systems Virus Reduction UF Systems VGS-600 and VCT-1 The VGS-600 and VCT-1 Virus Reduction UF Systems provide reliable virus, bacteria and protozoan cyst reduction for safer and cleaner drinking water without incorporating chemicals into the media or to the filtered water. These systems are uniquely designed with integral carbon block and sediment pre-filtration for the reduction of chlorine taste and odor and for providing extended life of the internal membrane element. The systems utilize cartridges that are designed with greater filtration surface area than alternative anti-microbial carbon blocks and operate at a higher flow rates with lower pressure drops. This makes the VGS-600 and VCT-1 Virus Reduction Systems ideal for Point-of-Use (POU) applications. VCT-1 VGS-600 The VGS-600 and VCT-1 systems are tested and certified to NSF P231 Microbiological Water Purifiers. Tested and Certified by NSF International to NSF P231 Microbiological Water Purifiers based on the recommendations set forth in the USEPA Guide Standard and Protocol for Microbiological Water Purifiers (OPP Task Force Report, 1987). NSF/ANSI Standard 42 for the reduction of Chlorine Taste and Odor and NSF/ANSI Standard 53 for the reduction of cyst and turbidity. Typical Applications Under Sink, Separate Tap Drinking Water Fountains Food Preparation and Hand Washing Photography/Film Coffee Makers Offices, Restaurants

38 POINT-OF-USE SYSTEMS Virus Reduction UF Systems VGS-600 and VCT-1 VGS-600 Operating Specifications Pressure Range VCT psi ( bar) Filter Capacity 600 gallons (2,271 L) Temperature Range Rated Service Flow VGS-600: VCT-1: F ( C) psi ( bar) psi ( bar) Features and Benefits Protects and Cleans Removes virus, bacteria, cysts, and other particles down to micron in size without relying on the addition of chemicals to the water. No Pump Necessary Requires only water pressure to operate no need for an electric pump. Application Provides reduction of microorganisms in the water system due to water main breaks or water treatment failure during floods and power outages. No Maintenance No waste water or brine/concentrate flushing simply replace cartridge. Maximum Filtration Extra large filtering surface resists clogging. Powerful Flow Utilizes polysulfone membrane with proprietary membrane formulation to deliver high flow at low pressure drop. Longer Life Combined Fiberdyne carbon block and sediment pre-filtration for extended life and chlorine taste and odor reduction. PENTEK Protection Double O-ring end cap seals for robust sealing in PENTEK Seal-Safe 3G housings. No Fouling Filter not susceptible to common substances in water, such as hydrogen sulfide (H 2 S), natural organic matter (NOM), and total dissolved solids (TDS). Retains natural mineral content of water. EPA Est. No WI-001 Not certified for sale in California, Iowa and Wisconsin. WARNING: These systems are intended for the disinfection of microbiologically contaminated water that meets all other public health standards. These systems are not intended for the treatment of water that has an obvious contamination or intentional source, such as raw sewage. These systems are not intended to convert wastewater or raw sewage into potable drinking water. These systems are intended for use on visually clear water. Operating Specifications VGS-600 and VCT-1 with DVG-50 Cartridge Influent Max. Permissible Challenge Product Water Reduction Average Substance Concentration Concentration Requirements Reduction P231 Bacteria: Raoultella terringena (ATCC-33257) 2.8 x 10 7 / 100 ml % 7.43 log Virus: MS-2 (ATCC B1) 4.3 x 10 4 / ml 99.99% 4.66 log STANDARD 42 Chlorine Taste & Odor 2.0 mg / L ± 10% 50% 97.4% STANDARD 53 Turbidity 11 ± 1 NTU 0.5 NTU 99% Cyst Min 50,000 / L 99.95% 99.99% Enterprise Avenue 5730 North Glen Park Road 2010 Pentair Residential Filtration, LLC Brookfield, WI Milwaukee, WI Rev A MY10 Tel: Tel: Fax: Fax: Customer Care:

39 S1 SERIES PLEATED CELLULOSE SEDIMENT Pleated design maximizes dirt-holding capacity Designed for general water filtration purposes Economically priced Nominal 20-micron rating Materials of Construction Filter Media: Resin-Impregnated Cellulose End Caps: Vinyl Plastisol Core: Polypropylene Netting: Polyethylene Temperature Rating: 40 F to 145 F (4.4 C to 63 C) S1-20 S1-20BB S1 S1-BB P1 P SERIES SPUN-BONDED POLYPROPYLENE Manufactured from pure 100% polypropylene Designed for purity, bacteria and chemical resistance Spun fibers form a true gradient density from outer to inner surfaces Materials of Construction Filter Media: Polypropylene Fibers Temperature Rating: 40 F to 145 F (4.4 C to 63 C) P5-478 P5 P5-20 P5-30 DGD DGD-2501 CW-F CP5-20 CW-50 CP-1 CP-5 CP5-BB CW-MF CP5-20BB DGD SERIES DUAL-GRADIENT DENSITY Manufactured from 100% pure polypropylene Designed for purity, with bacteria and chemical resistance Two separate gradient density layers enhance cartridge performance Three times the dirt-holding capacity of similar-sized sediment cartridges CW/WP SERIES POLYPROPYLENE WOUND String-wound design reduces fine sediment from a variety of fluids Withstands temperatures up to 165 F (74 C) Economically priced Nominal 5-, 20-, 50-micron rating (CW) and nominal 5-, 30-micron rating (WP) CP SERIES PLEATED CELLULOSE POLYESTER Special formulation of resin-impregnated cellulose and polyester fibers Provides higher wet strength than regular cellulose cartridges No unloading and minimal media migration Materials of Construction Filter Media: Polypropylene Temperature Rating: 40 F to 145 F (4.4 C to 63 C) Materials of Construction Filter Media: Polypropylene Fiber Cord Core: Polypropylene Temperature Rating: 40 F to 165 F (4.4 C to 74 C) Materials of Construction Filter Media: Cellulose Polyester Core: Polypropylene End Caps: Vinyl Plastisol Maximum Temperature: 125 F (52 C)

40 HFCP SERIES PLEATED CELLULOSE POLYESTER Special formulation of resin-impregnated cellulose and polyester fibers Provides higher wet strength than regular cellulose cartridges No unloading and minimal media migration Designed for high flow rate and high dirt-holding applications Materials of Construction Filter Media: Cellulose Polyester Core: Vented Polypropylene End Caps: Molded Polypropylene Netting: Polyethylene Gasket: Buna-N & EPR Temperature Rating: 40 F to 165 F (4.4 C to 74 C) HFCP-1 HFCP-5 PP SERIES POLYPROPYLENE PLEATED Pleated design maximizes dirt-holding capacity Durable polypropylene media resists bacterial attack Suitable for municipal or well water applications Nominal 30-micron rating Materials of Construction Filter Media: Non-Woven Polypropylene Core: Polypropylene End Caps: Vinyl Plastisol Netting: Polyethylene (PP-30 only) Gasket: Buna-N & EPR Temperature Rating: 40 F to 145 F (4.4 C to 63 C) PP-30 PP30-BB R SERIES PLEATED POLYESTER Pleated design maximizes dirt-holding capacity Versatile and reusable, allowing for a variety of uses Durable polyester media is bacteria and chemical resistant Nominal 30-micron rating (R-30) and nominal 50-micron rating (R-50) Materials of Construction Filter Media: Non-Woven Polyester Core: Polypropylene End Caps: Vinyl Plastisol Temperature Rating: 40 F to 125 F (4.4 C to 52 C) R30-20 R30-BB R50 CRE SERIES CERAMIC Specially designed for cyst reduction and fine sediment filtration applications 1/2" thick ceramic wall allows for many cleanings, extending cartridge life Nominal 1-micron rating POLYDEPTH POLYPROPYLENE SEDIMENT Quality polypropylene filter media Will not impart taste, odor or color Superior chemical resistance. Not prone to bacterial attack Compatible with a wide range of industrial filtration Available in a wide range of micron ratings and lengths Materials of Construction Filter Media: Sintered Ceramic End Caps: Thermoset Polymeric Gasket: Buna-N Temperature Rating: 40 F to 125 F (4.4 C to 52 C) Materials of Construction Filter Media: Polypropylene Temperature Rating: 40 F to 175 F (4.4 C to 79.4 C) R50-BB CRE-1 R30 POLYDEPTH Polypropylene Sediment Cartridge

41 C1-20 C2 C8 C1 C1-20BB C SERIES DUAL PURPOSE POWDERED- ACTIVATED CARBON Economically priced Provides sediment filtration and taste, odor and chlorine reduction High dirt-holding capacity Available in four sizes and two micron ratings Materials of Construction Filter Media: PAC Impregnated Cellulose End Caps: Polypropylene (C8) Vinyl Plastisol (C1 and C2) Netting: Polyethylene Core: Polypropylene Backing: Polyester(C8) Cellulose Polyester(C1andC2) Gasket: Buna-N (C8) (Optional EPR Gaskets) Temperature Rating: 40 F to 145 F (C8) (4.4 C to 63 C) 40 F to 125 F (Others) (4.4 C to 52 C) NCP-20 NCP SERIES NON-CELLULOSE CARBON-IMPREGNATED PLEATED Non-cellulose media resists bacterial attack Provides sediment filtration and taste, odor and chlorine reduction Pleated for maximum dirt-loading capacity Nominal 10-micron rating Materials of Construction Filter Media: Pleated Carbon-Impregnated Polyester End Caps: Vinyl Plastisol Core: Polypropylene Netting: Polyethylene Temperature Rating: 40 F to 150 F (4.4 C to 65.6 C) NCP-10 NCP-BB NCP-20BB GAC-10 GAC-5 GAC-20 GAC-BB CC-20 CC-BB CC-10 CC-20BB CGAC-10 GAC-20BB GAC SERIES GRANULAR ACTIVATED CARBON Effective taste, odor and chlorine reduction Designed for maximum adsorption Post-filter to reduce carbon fines Available in a variety of sizes and flow rates CC SERIES COCONUT SHELL GRANULAR ACTIVATED CARBON Effective taste, odor and chlorine reduction Greater VOC reduction than standard GAC cartridges Post-filter to reduce carbon fines Available in a variety of sizes and flow rates CGAC-10 GRANULAR ACTIVATED CARBON Effective taste, odor, chlorine, and chloramine reduction Advanced catalytic carbon media Designed for maximum adsorption Post-filter to reduce carbon fines Materials of Construction Filter Media: Granular-Activated Carbon End Caps: Polystyrene Post-filter: Spun Polypropylene Outer Casing: Polystyrene Expansion Pad: Polyester Gaskets: Buna-N (top) Santoprene (bottom) Temperature Rating: 40 F to 125 F (4.4 C to 52 C) Materials of Construction Filter Media: Granular Activated Carbon End Caps: Polystyrene Core: Spun Polypropylene Outer Casing: Polystyrene Expansion Pad: Polyester Gaskets: Buna-N (Top) Santoprene (Bottom) Temperature Rating: 40 F to 125 F (4.4 C to 52 C) Materials of Construction Filter Media: Catalytic Carbon End Caps: Polystyrene Post-filter: Spun Polypropylene Outer Casing: Polystyrene Expansion Pad: Polyester Gaskets: Buna-N (top) Santoprene (bottom) Temperature Rating: 40 F to 125 F (4.4 C to 52 C)

42 SGAC SERIES SILVER-IMPREGNATED GRANULAR ACTIVATED CARBON Effective taste, odor and chlorine reduction Silver-impregnated carbon media inhibits the growth of bacteria Designed for maximum adsorption Post-filter to reduce carbon fines Materials of Construction Filter Media: Silver-Impregnated Granular-Activated Carbon End Caps: Polystyrene Post-filter: Spun Polypropylene Outer Casing: Polystyrene Gaskets: Buna-N (top) Santoprene (bottom) Temperature Rating: 40 F to 125 F (4.4 C to 52 C) SGAC-10 TSGAC SERIES SPECIALTY GRANULAR ACTIVATED CARBON/PHOSPHATE Effective taste, odor and chlorine reduction Phosphate crystals reduce rust stains and scale deposits Designed for maximum adsorption Post-filter to reduce carbon fines Materials of Construction Filter Media: Granular-Activated Carbon Hexametaphosphate Crystals End Caps: Polystyrene Post-filter: Spun Polypropylene Outer Casing: Polystyrene Expansion Pad: Polyester Gaskets: Buna-N (top) Santoprene (bottom) Temperature Rating: 40 F to 125 F (4.4 C to 52 C) TSGAC-10 RFC SERIES RADIAL FLOW CARBON Ideal for point-of-entry (POE) and other high flow rate applications Unique design reduces carbon fines in filtered water Available in a wide variety of sizes Materials of Construction Filter Media: Granular Activated Carbon End Caps: Polypropylene Outer Shell: Polyethylene Inner/Outer Wrap: Polypropylene Gaskets: Buna-N Temperature Rating: 40 F to 125 F (4.4 C to 52 C) RFC20-BB EPM SERIES MODIFIED EPSILON CARBON-BRIQUETTE Economically priced High porosity maximizes utilization of the carbon block Greater chlorine-removal capacity than competitive 10-micron carbon blocks. Nominal 10-micron rating EP SERIES CARBON-BRIQUETTE High-dirt-holding tolerance maximizes utilization of the carbon block Greater chlorine reduction capacity than competitive 10-micron carbon blocks Nominal 5-micron rating Materials of Construction Filter Media: Bonded PAC End Caps: Polypropylene Netting: Polyethylene Outer Wrap: Polypropylene Gaskets: Buna-N Temperature Rating: 40 F to 180 F (5 C to 83 C) Materials of Construction Filter Media: Bonded PAC End Caps: Polyethylene Netting: Polypropylene Inner/Outer Wrap: Polypropylene Gaskets: Buna-N Temperature Rating: 40 F to 180 F (5 C to 83 C) RFC-20 RFC-93 RFC-BB EPM-20BB EPM-10 EPM-BB EPM-20 EP-20 EP20-BB EP-BB EP-10

43 CBC-20BB CBC SERIES CARBON-BRIQUETTE Reduces taste, odor, chlorine and certain VOCs from drinking water Effective at filtering Cryptosporidium and Giardia cysts High capacity chlorine reduction Nominal 0.5-micron rating Materials of Construction Filter Media: Bonded PAC End Caps: Polypropylene Inner/Outer Wraps: Polypropylene Netting: Polyethylene Temperature Rating: 40 F to 180 F (5 C to 83 C) CBC-20 CBC-BB CBC-5 CBC-10 CCBC SERIES COCONUT BASED CARBON BLOCK Water-washed coconut-carbon formulation Reduces taste, odor, chlorine and certain VOCs from drinking water Effective at filtering Cryptosporidium and Giardia cysts Nominal 1-micron rating Materials of Construction Filter Media: Water-Washed Coconut Based Carbon End Caps: Polypropylene Inner/Outer Wraps: Polypropylene Netting: Polyethylene Gaskets: Buna-N Temperature Rating: 40 F to 180 F (5 C to 83 C) CCBC-10 CBR2 SERIES CARBON-BRIQUETTE MULTIMEDIA Highly effective chlorine reduction through more than 20,000 gallons Lead reduction through 2000 gallons 99.95% reduction of Cryptosporidium and Giardia cysts Nominal 0.5-micron sediment filtration Materials of Construction Filter Media: Bonded PAC End Caps: Polypropylene Outer Wrap: Polypropylene Netting: Polyethylene Gaskets: Buna-N Temperature Rating: 40 F to 180 F (4.4 C to 83 C) CCBR2-10 CEP-20E CEP-10E CBR2-10 CBR2-10R CEP-20BB CEP-10BB OAC-20BB CEP SERIES COCONUT BASED CARBON BLOCK Acid-washed coconut-carbon formulation Low extractables, minimal ph rise Greater chlorine removal capacity than competitive 10-micron carbon blocks Nominal 5-micron rating OAC-20BB OIL ABSORBING High efficiency removal of oils or glycol Instantaneous absorption, more effective than activated carbon 90% of total hydrocarbons are removed in a single pass For use in 20-inch Big Blue filter housings Materials of Construction Filter Media: Acid-Washed Coconut Based Carbon End Caps: Polypropylene Inner/Outer Wraps: Polypropylene Netting: Polyethylene Gaskets: Buna-N Temperature Rating: 40 F to 125 F (5 C to 52 C) Materials of Construction Filter Media: Modified Cellulose End Caps: PVC Plastisol Core: Natural Polypropylene Netting: Polyethylene Temperature Rating: 40 F to 125 F (4.4 C to 52 C) Media Area: 18 sq ft (1.6 sq m) Weight: 2.0 lbs (0.7 kg)

44 WS SERIES WATER SOFTENER Convenient cartridge change-out Manufactured with FDA-grade softener resin 750 to 4,500 grain capacity available (CaCo3) For use in standard and Big Blue filter housings Materials of Construction Filter Media: Standard Softener Resin End Caps: Polypropylene Gasket: Buna-N Temperature Rating: 100 F (38 C) WS-10 WS-20 WS-20BB PCC SERIES HEXAMETAPHOSPHATE CRYSTAL Highly effective at treating scale, corrosion and iron problems Ideal for a variety of food service equipment, as well as other types of water processing equipment Materials of Construction Filter Media: Food Grade Polyphosphate Shell: Polypropylene Pre-Filter: Polyester Post-Filter: Polypropylene Gaskets: Buna-N Temperature Rating: 40 F to 100 F (4.4 C to 38 C) PCC212 PCC218 PCC10 PCC1 RADIAL FLOW IRON REDUCTION Easily and effectively reduces iron in water up to 3 ppm Improves flavor and reduces the metallic taste caused by iron Reduces the possibility of pipe and water heater damage For use in 20-inch Big Blue filter housings PCF SERIES MIXED BED DEIONIZATION Designed for deionizing water up to 16 megaohms All materials and construction are FDA-compliant Three sizes and capacities BP SERIES POLYPROPYLENE BAGS Thermally welded seams result in consistent filtration efficiencies Increased surface area means less frequent bag changes Semi-rigid cylindrical design is easily crushed and incinerated Recommended Operating Conditions ph: >7.0 Silica: <100 ppm Manganese: <1 ppm Iron: <3 ppm Iron Bacteria: None Hydrogen Sulfide: None Materials of Construction Filter Media: Mixed bed DI resins End Caps: Polypropylene Shell: Polypropylene Pre-Filter: Polyester Post-Filter: Polypropylene Gaskets: Buna-N Temperature Rating: 40 F to 100 F (4.4 C to 38 C) Materials of Construction Top: Polypropylene Filter Media: Felt Micron Rating: Maximum Temperature: 200 F (93 C) PCF1-10MB RFFE20-BB BBF1-20MB PCF1-20MB BP-420 BP-410

45 C SERIES CARTRIDGES C1-20 C1 C2 C8 C Series cartridges offer an economical solution for all your general-purpose water filtration needs. Constructed of a carbon impregnated cellulose media, these dual-purpose cartridges filter out fine sediment particles and reduce unwanted taste, odor, and chlorine taste & odor from your tap water.* A polyester reinforcement backing and external netting provide additional strength and dirt-loading capacity. C Series cartridges are available in three (3) different sizes and two (2) different micron ratings. Both the C1 and C2 are nominally rated at 5-microns, the C8 is nominally rated at 1-micron. These dual-purpose cartridges are well suited for a wide range of residential applications, and make excellent polishing filters when used in process or closed-loop streams. * Based on manufacturer s internal testing. FEATURES

46 C1 C1-20 C2 C8 C " x 9 3 4" (64 mm x 248 mm) gpm ( Lpm) >5,000 1 gpm (>11, Lpm)* CS " x 9 3 4" (57 mm x 248 mm) gpm ( Lpm) >3,000 1 gpm (>5, Lpm)* C " x 4 7 8" (64 mm x 124 mm) gpm ( Lpm) >2, gpm* (>5, Lpm) C8 C " x 9 3 4" (67 mm x 248 mm) 2 1 2" x 20" (64 mm x 508 mm) Filter Media End Caps Netting Core PAC Impregnated Cellulose Polypropylene (C8), Vinyl Plastisol (C1, C2 and CS1) Polyethylene Polypropylene gpm ( Lpm) 1 5 gpm ( Lpm) Reinforcement Backing Polyester (C8), Cellulose Polyester (C1 and C2) Gasket Buna-N (C8) Temperature Rating 40 F to 145 F (4.4 C to 62.8 C)(C8), 40 F to 125 F (4.4 C to 51.7 C)(C1, C2, C1-20) WARNING: For drinking water applications, do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. NOTE: Increased flow rates may result in less effective chlorine reduction. Sheboygan, Wisconsin NOTE: Some harmless bacteria will attack cellulose media cartridges. If your cartridge seems to disintegrate, or has a musty or moldy odor, switch to a synthetic media cartridge or consult the manufacturer. *NOTE: Estimated capacity tested at given flow rate using 2 ppm free available chlorine to 0.5 ppm breakthrough. >8,000 1 gpm* (>30, Lpm) >10,000 2 gpm* (>37, Lpm) The C1 is Tested and Certified by NSF International to NSF/ANSI Standard 42 for material requirements only Pentair Filtration, Inc AP08

47 CBC SERIES CARTRIDGES CBC-20BB CBC SERIES CARBON-BRIQUETTE CARTRIDGES CBC-BB CBC-20 CBC Series cartridges are highly effective at reducing unwanted bad taste and odor, and chlorine taste & odor, from potable drinking water. The unique structure of the carbon block enables it to reduce Giardia, Cryptosporidium, Entamoeba, and Toxoplasma cysts and fine sediment particles down to 0.5 microns.* CBC Series cartridges are manufactured using a patented process and made entirely from FDA-compliant materials. They are an ideal choice for a wide range of residential, food service, commercial and industrial applications. They also make excellent polishing filters or pre-filters in applications requiring fine filtration and high capacity. * Based on manufacturer s internal testing. CBC-5 CBC-10

48 CBC SERIES 70 Approximate Net Pressure Drop psi (Bar) CBC-10 CBC10-BB CBC-5 CBC-20 CBC20-BB Flow Rate gpm (Lpm) CBC " x 4 7 8" (73 mm x 124 mm) gpm ( Lpm) CBC " x 9 3 4" (73 mm x 248 mm) gpm ( Lpm) CBC " x 20" (73 mm x 508 mm) gpm ( Lpm) CBC-BB 4 5 8" x 9 3 4" (118 mm x 248 mm) gpm ( Lpm) CBC20-BB 4 5 8" x 20" (118 mm x 508 mm) gpm ( Lpm) Filter Media End Caps Inner/Outer Wraps Netting Gaskets Temperature Rating Bonded PAC Polypropylene Polyolefin Polyethylene Santoprene ºF ( ºC) > gpm 3.8 Lpm) >20,000 2 gpm 7.6 Lpm) >45,000 2 gpm 7.6 Lpm) >50,000 2 gpm 7.6 Lpm) >150,000 4 gpm 15.1 Lpm) The CBC-10, CBC-20, CBC-BB and CBC- 20BB are Tested and Certified by NSF International to NSF/ANSI Standard 42 for material requirements only. WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. NOTE: Performance capacity depends on system design, flow rate and certain other application conditions. Certain states require system registration or certification for health-related contaminant reduction claims. NOTE: Cartridges will contain a very small amount of carbon fines (very fine black powder) and a new cartridge after installation should be flushed with sufficient water to remove all traces of the fines from your water system before using the water. Each time you use your filtered water tap for drinking or cooking purposes it is recommended that you run (flush) the tap for at least 20 seconds prior to using water. NOTE: Micron ratings based on 85% or greater removal of given particle size. NOTE: CBC-Series cartridges are capable of reducing 99.95% of Cryptosporidium and Giardia cysts. Data obtained from actual particle counts using AC Fine Test Dust and Latex spheres. Estimated capacity using 2ppm free available chlorine (FAC) with greater than 90% reduction. U.S. Patent No. 5,976,432 & 5,823, Pentair Filtration, Inc. Printed in USA JA

49 CBR2 SERIES CARTRIDGES CBR2 SERIES CARBON BRIQUETTE MULTI-MEDIA CARTRIDGES The CBR2-10 and CBR2-10R are advanced multimedia cartridges designed to reduce chlorine taste and odor, dissolved and particulate lead, cysts, MTBE and certain volatile organic chemicals (VOCs).* CBR2 Series cartridges are manufactured using a patented process, and combine powdered activated carbon (PAC) with a specially designed adsorbent medium for lead and mercury reduction. These cartridges are protected by Endurawrap, a uniquely formulated polyolefin bilaminate prefilter, designed to significantly increase the useful life of the cartridge by trapping sediment that typically plugs carbon block cartridges. In addition to lead reduction, the unique structure of the carbon block enables it to reduce Giardia, Cryptosporidium, Entamoeba and Toxoplasma cysts and fine sediment particles down to 0.5 microns.* As with our standard CBC Series carbon block, both the CBR2-10 and CBR2-10R are effective at reducing levels of chlorine taste & odor, MTBE and VOCs.* The CBR2-10R has a built-in flow restrictor (0.6 gpm) to allow for maximum contact time. * Based on manufacturer s internal testing. CBR2-10 CBR2-10R

50 CBR2 SERIES CBR2-10 CBR2-10R 2 7 8" x 9 3 4" (73 mm x 124 mm) 2 7 8" x 9 3 4" (73 mm x 124 mm) gpm ( Lpm) Flow restricted to 0.6 gpm (2.3 Lpm) with built-in Flow restrictor Cyst Reduction* >99.95% Lead & Mercury Reduction* gpm 3.8 Lpm) >20,000 1 gpm 3.8 Lpm) >20, gpm 2.3 Lpm) Lpm) Lpm) Lpm) Lpm) This CBR2-10 and CBR2-10R are Tested Filter Media Bonded PAC and Certified by NSF International to End Caps Polypropylene NSF/ANSI Standard 42 for material requirements only. Outer Wrap Polyolefin Netting Polyethylene Gaskets Buna-N Temperature Rating ºF ( ºC) NOTE: Certain state require system registration or certification for health-related contaminant reduction claims. NOTE: Chlorine and lead reduction tests conducted by Pentair Water Treatment at 0.6 gallons per minute with a Pentek Slim Line (SL) housing. NOTE: Meets NSF Standard 42 for chlorine taste & odor reduction.* WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the unit. NOTE: Giardia, Cryptosporidium, Entamoeba and Toxoplasma cyst claim based on tests showing greater than 99.95% reduction using NSF Standard 53 protocol. U.S. Patent No. 5,976,432 & 5,823, Pentair Filtration, Inc. Printed in USA AU

51 CC SERIES CARTRIDGES CC SERIES COCONUT SHELL GRANULAR ACTIVATED CARBON CARTRIDGE CC Series granular activated carbon cartridges are an excellent choice to reduce unwanted chlorine taste & odor, and certain VOC's from potable drinking water. CC-10 cartridges also reduce MTBE. They contain coconut shell based activated carbon, which produces drinking water of exceptional taste and quality and provides better VOC reduction than standard GAC cartridges.* The construction of the cartridges allows water to enter at one end and pass through the entire length of the carbon bed before exiting the other end of the cartridge, while an internal expansion pad minimizes channeling or bypass. Before the water exits the cartridge, a 20- micron post-filter helps remove carbon fines and other suspended particles from the filtered water. The post-filter is permanently fastened to an innovative support basket ensuring that it is firmly secured, eliminating any potential for bypass. CC Series cartridges effectively provide good general purpose drinking water filtration. * Based on manufacturer s internal testing. CC-10 USCC-10SL

52 CC SERIES CC " x 9 3 4" (73 mm x 248 mm) gpm ( Lpm) USCC-10SL 2 1 2" x 9 3 4" (64 mm x 248 mm) 20 8 gpm (0.55 Lpm) 7,500 1 gpm 3.8 Lpm) 3,500 1 gpm 3.8 Lpm) Filter Media End Caps Post-Filter Outer Casing Expansion Pad Granular Activated Carbon Polystyrene Spun Polypropylene Polystyrene Polypropylene The CC-10 is Tested and Certified by NSF International to NSF/ANSI Standard 42 for material requirements only. The USCC-10SL is Tested and Certified by NSF International to NSF/ANSI Standard 42 in model US-550 and US-600. See Performance Data Sheet for specific claims. Buna-N (top) Gasket Santoprene (bottom) Temperature Rating ºF ( ºC) NOTE: Performance capacity depends on system design, flow rate and certain other application conditions. Certain states require system registration or certification for health-related reduction claims. WARNING: For drinking water applications, do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. NOTE: A drinking water cartridge may contain carbon fines (very fine black powder). After installation and before using the water, follow the instructions for flushing the cartridge to remove fines. NOTE: It is recommended that you run the tap for 20 seconds prior to using the water for drinking or cooking purposes Pentair Filtration, Inc. Printed in USA MR

53 CEP-10E CARTRIDGE CEP-10E CEP-10E COCONUT BASED CARBON BLOCK CARTRIDGE Nominal 5-micron rating* Acid-washed coconut-carbon formulation Bad taste & odor and chlorine taste & odor reduction* Low extractables, minimal ph rise for RO pre- and post-filter applications* Enhanced dirt holding capacity* CEP-10E cartridges are manufactured from an acid-washed coconut-carbon based formulation that minimizes the ph rise and produces better tasting water. Our patented manufacturing process yields a cartridge with a nominal 5- micron filtration rating, low extractables and a minimal ph rise ideal for RO pre- and post-filter applications. A thin-wall, high porosity design helps prevent the cartridge from plugging before its adsorption capacity is exhausted, maximizing the utilization of the carbon while maintaining low pressure drop. These cartridges are protected by Endurawrap, a uniquely formulated polyolefin bilaminate prefilter, designed to significantly increase the useful life of the cartridge by trapping sediment that typically plugs carbon block cartridges. * Based on manufacturer s internal testing.

54 CEP-10E Coconut Based Carbon Block Cartridge 30 (2.1) Percent Efficiency Approximate Net Pressure Drop psi (bar) 25 (1.7) 20 (1.4) 15 (1.0) 10 (0.7) 5 (0.3) Particle Size (Microns) (7.6) (15) (23) (30) (38) (45) Flow Rate gpm (L/min) Tested and Certified by NSF International to NSF/ANSI Standard 42 for material requirements only. Cartridge Specifications and Performance Data Maximum Micron Rating Initial ΔP (psi) Chlorine Taste & Odor Reduction* Model Dimensions Flow Rate Flow Rate (gpm) CEP-10E 2-7/8" x 9-3/4" gpm >5,000 1 gpm (73 mm x 248 mm) ( L/min) (18, L/min) * Based on manufacturer s internal testing. Materials of Construction Filter Media End Caps Inner/Outer Wraps Netting Acid-Washed Coconut Based Carbon Polypropylene Polyolefin Polyethylene Gaskets Temperature Rating WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. U.S. Patent No. 5,976,432 & 5,823,668 Buna-N 40 F to 125 F (4.4 C to 51.7 C) 2007 Pentair Water Treatment 502 Indiana Avenue P.O. Box 1047 Sheboygan, Wisconsin Customer Service: Fax: supportspecialist@pentekfiltration.com International: Fax: international@pentekfiltration.com Printed in U.S.A. MR

55 CFB SERIES CARTRIDGES CFB-30 CFB SERIES MODIFIED MOLDED BLOCK CARTRIDGES CFB Series cartridges provide the effective chlorine taste & odor reduction found in traditional carbon block media while offering excellent sediment reduction capabilities.* CFB Series products are a modified molded block created by use of our proprietary Fibredyne technology. This technology creates a unique filter media by attaching powdered activated carbon onto a cellulosefree synthetic fiber matrix. The result is a single cartridge that combines the benefits of both a sediment filter and a carbon block into a single cartridge. Fibredyne's carbon block technology also offers up to two times the chlorine taste & odor reduction and dirt-holding capacity of traditional blocks.* In addition, this technology will not release fines into the effluent stream due to a unique post-filtration layer that is fused to the carbon/fiber media blend. CFB Series cartridges are manufactured entirely from FDAcompliant materials, making them an ideal choice for a wide range of residential, food service, commercial and industrial applications. * Based on manufacturer's internal testing. CFB-10 CFB-20

56 CFB SERIES Tested and Certified by NSF International to NSF/ANSI Standard 42 for material requirements only. CFB-10 CFB-20 CFB " x 9 3 4" (73mm x 248mm) 2 7 8" x 20" (73mm x 508mm) 2 7 8" x 30" (73mm x 762mm) Filter Media End Caps Netting Gaskets Bonded PAC Polypropylene Polyethylene Santoprene gpm ( Lpm) gpm ( Lpm) gpm ( Lpm) >5,000 1 gpm (>18, Lpm) >10,000 2 gpm (>37, Lpm) >15,000 3 gpm (>56, Lpm) WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the unit. NOTE: Performance capacity depends on system design, flow rate and certain other application conditions. Certain states require system registration or certification for health-related contaminant reduction claims. NOTE: Cartridges will contain a very small amount of carbon fines (very fine black powder). After installation, a new cartridge should be flushed with sufficient water to remove all traces of fines prior to using the water. NOTE: Micron ratings based on 85% or greater removal of given particle size. Estimated capacity using 2ppm free available chlorine at 0.5 ppm breakthrough. 40 F-180 F (4.4 C-82.2 C) 40 F-180 F (4.4 C-82.2 C) 40 F-180 F (4.4 C-82.2 C) 2006 Pentair Filtration, Inc. Printed in USA JE

57 CFB-PB10 CARTRIDGE FIBREDYNE CFB-PB10 LEAD REDUCTION MODIFIED MOLDED BLOCK CARTRIDGE The CFB-PB cartridge offers the benefits of effective chlorine taste & odor, cyst and lead reduction found in traditional carbon block media while offering premium sediment filtration.* The CFB-PB product is modified molded block manufactured using our proprietary Fibredyne technology. This technology creates a unique filter media by attaching powdered activated carbon and lead adsorbent material onto a cellulose-free synthetic fiber matrix. This results in higher reduction efficiencies that resist plugging, afford the longest life, and feature the lowest pressure drop over the effective life of the cartridge of any available 0.5 micron filter cartridge.* Fibredyne's carbon block technology also offers up to two times the chlorine taste & odor reduction and dirt-holding capacity of traditional blocks.* In addition, this technology will not release fines into the effluent stream due to a unique postfiltration layer that is fused to the carbon/fiber media blend. CFB-PB10 The CFB-PB cartridge is manufactured entirely from FDAcompliant materials, making it an ideal choice for a wide range of residential, food service, commercial and industrial applications. * Based on manufacturer's internal testing.

58 CFB-PB10 CARTRIDGE Tested and Certified by NSF International to NSF/ANSI Standard 42 for material requirements only. CFB-PB " x 9 3 4" (73mm x 248mm) gpm ( Lpm) >5,000 1 gpm (>18, Lpm) 40 F-180 F (4.4 C-82.2 C) Filter Media Bonded PAC End Caps Polypropylene Netting Polyethylene Gaskets Santoprene WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the unit. NOTE: Performance capacity depends on system design, flow rate and certain other application conditions. Certain states require system registration or certification for health-related contaminant reduction claims. NOTE: Cartridges will contain a very small amount of carbon fines (very fine black powder). After installation, a new cartridge should be flushed with sufficient water to remove all traces of fines prior to using the water. NOTE: Micron ratings based on 85% or greater removal of given particle size. Estimated capacity using 2ppm free available chlorine at 0.5 ppm breakthrough. NOTE: Giardia, Cryptosporidium, Entamoeba and Toxoplasma cyst claim based on tests showing greater than 99.95% reduction using NSF Standard 53 protocol Pentair Filtration, Inc. Printed in USA JE

59 CFB-PLUS SERIES CARTRIDGES CFB-Plus30 CFB-Plus 10BB CFB-PLUS SERIES MODIFIED MOLDED BLOCK CARTRIDGES CFB-Plus 20BB CFB-Plus 20 The CFB-Plus Series cartridges are an enhanced version of our CFB product. It offers the same benefits with even greater chlorine taste & odor reduction and the highest sediment reduction found in a carbon cartridge.* CFB-Plus Series products are modified molded blocks manufactured using our proprietary Fibredyne technology. This technology creates a unique filter media by attaching powdered activated carbon onto a cellulosefree synthetic fiber matrix. The result is a single cartridge that combines the benefits of both a sediment filter and a carbon block into a single cartridge. Fibredyne's carbon block technology also offers up to two times the chlorine taste & odor reduction and dirt-holding capacity of traditional blocks.* In addition, this technology will not release fines into the effluent stream due to a unique postfiltration layer that is fused to the carbon/fiber media blend. CFB-Plus Series cartridges are manufactured entirely from FDAcompliant materials, making them an ideal choice for a wide range of residential, food service, commercial and industrial applications. * Based on manufacturer's internal testing. CFB-Plus

60 CFB-PLUS SERIES Tested and Certified by NSF International to NSF/ANSI Standard 42 for material requirements only. CFB-Plus10 CFB-Plus20 CFB-Plus30 CFB-Plus10BB CFB-Plus20BB 2 7 8" x 9 3 4" (73mm x 248mm) 2 7 8" x 20" (73mm x 508mm) 2 7 8" x 30" (73mm x 762mm) 4 5 8" x 9 3 4" (118mm x 248mm) 4 5 8" x 20" (118mm x 508mm) Filter Media End Caps Netting Gaskets Bonded PAC Polypropylene Polyethylene Santoprene gpm ( Lpm) gpm ( Lpm) gpm ( Lpm) gpm ( Lpm) gpm ( Lpm) >10,000 1 gpm (>37, Lpm) >20,000 2 gpm (>75, Lpm) >30,000 3 gpm (>113, Lpm) >25,000 2 gpm (>94, Lpm) >50,000 4 gpm (>189, Lpm) WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the unit. NOTE: Performance capacity depends on system design, flow rate and certain other application conditions. Certain states require system registration or certification for health-related contaminant reduction claims. NOTE: Cartridges will contain a very small amount of carbon fines (very fine black powder). After installation, a new cartridge should be flushed with sufficient water to remove all traces of fines prior to using the water. NOTE: Micron ratings based on 85% or greater removal of given particle size. Estimated capacity using 2ppm free available chlorine at 0.5 ppm breakthrough. 40 F-180 F (4.4 C-82.2 C) 40 F-180 F (4.4 C-82.2 C) 40 F-180 F (4.4 C-82.2 C) 40 F-180 F (4.4 C-82.2 C) 40 F-180 F (4.4 C-82.2 C) 2006 Pentair Filtration, Inc. Printed in USA JE

61 CFBC SERIES CARTRIDGES CFBC-20 CFBC SERIES MODIFIED MOLDED BLOCK CARTRIDGES CFBC Series cartridges offer the effective chlorine taste and odor reduction found in traditional carbon block media while providing superior sediment reduction with resistance to premature plugging. They are highly effective at reducing chlorine taste & odor, bad taste and odor, as well as some organic chemicals.* CFBC Series products are modified molded blocks manufactured using our proprietary Fibredyne technology. This technology creates a unique filter media by attaching powdered activated carbon onto a cellulose-free synthetic fiber matrix. The result is a single cartridge that combines the benefits of both a sediment filter and a carbon block into a single cartridge. Benefits of this technology include low pressure drop over the entire life of the cartridge and up to three times the chlorine taste & odor and dirt-holding capacity of traditional 0.5 micron carbon blocks.* In addition, Fibredyne's technology will not release fines into the effluent stream due to a unique postfiltration layer that is fused to the carbon/fiber media blend. CFBC Series cartridges are manufactured entirely from FDAcompliant materials, making them an ideal choice for a wide range of residential, food service, commercial and industrial applications. * Based on manufacturer s internal testing. CFBC-10

62 CFBC SERIES Tested and Certified by NSF International to NSF/ANSI Standard 42 for material requirements only. CFBC-10 CFBC " x 9 3 4" (73mm x 248mm) 2 7 8" x 20" (73mm x 508mm) Filter Media End Caps Netting Gaskets Bonded PAC Polypropylene Polyethylene Santoprene gpm ( Lpm) gpm ( Lpm) WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the unit. >20,000 1 gpm (>75, Lpm) >40,000 2 gpm (>75, Lpm) NOTE: Performance capacity depends on system design, flow rate and certain other application conditions. Certain states require system registration or certification for health-related contaminant reduction claims. NOTE: Cartridges will contain a very small amount of carbon fines (very fine black powder). After installation, a new cartridge should be flushed with sufficient water to remove all traces of fines prior to using the water. NOTE: Micron ratings based on 85% or greater removal of given particle size. Estimated capacity using 2ppm free available chlorine at 0.5 ppm breakthrough. NOTE: Giardia, Cryptosporidium, Entamoeba and Toxoplasma cyst claim based on tests showing greater than 99.95% reduction using NSF Standard 53 protocol. 40 F-180 F (4.4 C-82.2 C) 40 F-180 F (4.4 C-82.2 C) 2006 Pentair Filtration, Inc. Printed in USA JE

63 CHLORAMINE REDUCTION CARTRIDGES ChlorPlus 20 CRFC20-BB ChlorPlus BB CHLORAMINE REDUCTION CARBON CARTRIDGES PENTEK offers multiple product solutions for chloramine reduction. Chloramine is increasingly becoming more common as an alternative to chlorine for water treatment. The ChlorPlus carbon block cartridges help reduce sediment while providing greater chloramine performance capacities than granular carbon. They also significantly reduce the carbon fines found in many granular canisters. The CRFC20-BB heavy duty radial flow cartridge measures inches in diameter and 20 inches long, which is ideal for higher flow rate and capacity applications. This cartridge incorporates a 70 micron porous polypropylene outer shell and a spun polypropylene-wrapped core. The bed of granular activated carbon (GAC) between the outer shell and core creates a unique radial flow design which effectively removes chloramine, has a low pressure drop, and helps to reduce fines commonly seen in GAC-style cartridges. All of these cartridges utilize advanced activated carbon technology which allows superior chloramine and chlorine reduction. The range of sizes and capacities offered by PENTEK chloramine reduction cartridges makes them ideal for both point-of-entry (POE) and point-of-use (POU) applications.

64 CHLORAMINE REDUCTION CARBON CARTRIDGES Net Pressure Drop (psi) ChlorPlus 10 ChlorPlus 20 ChlorPlus 10BB ChlorPlus 20BB CRFC-BB CRFC20-BB Chloramine Effluent Concentration (ppm) ChlorPlus gpm ChlorPlus 20-1 gpm 0.1 ChlorPlus 10BB - 2 gpm ChlorPlus 20BB - 4 gpm Flow Rate (gpm) -0.1 Volume (gallons) ChlorPlus " x 9¾" (73 mm x 248 mm) gpm ( Lpm) >50,000 1 gpm 3.8 Lpm) 2, gpm 1.9 L/min) 1, gpm 3.8 L/min) ChlorPlus " x 20" (73 mm x 508 mm) gpm ( Lpm) >100,000 2 gpm 7.6 Lpm) 5, gpm 3.8 L/min) 2, gpm 7.6 L/min) ChlorPlus 10BB 4 1 2" x 9¾" (114.3 mm x 248 mm) gpm ( Lpm) >250,000 2 gpm 7.6 Lpm) 3, gpm 7.6 L/min) ChlorPlus 20BB 4 1 2" x 20" (114.3 mm x 508 mm) gpm ( Lpm) >500,000 4 gpm 15.2 Lpm) 7, gpm 15.2 L/min) CRFC-BB CRFC20-BB 4 1 2" x 9¾" (114 mm x 248 mm) 4½" x 20" (114 mm x 508 mm) Filter Media gpm ( Lpm) <1 1.5 gpm (< Lpm) gpm ( Lpm) <1 2.5 gpm (< Lpm) >100,000 2 gpm 7.6 Lpm) >200,000 4 gpm 15.2 Lpm) Advanced Bonded PAC Endcaps Polypropylene Polypropylene Advanced Granular Activated Carbon Inner Wrap/Core Polyolefin Outer Wrap/Shell Polyolefin Polyethylene Expansion Pad N/A N/A Post Filter N/A Netting Polyethylene N/A Gasket Temperature Rating ºF ( ºC) ºF ( ºC) 12, gpm 5.7 L/min) 5, gpm 9.5 L/min) 25, gpm 9.5 L/min) 10, gpm 18.9 L/min) WARNING: For drinking water applications, do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. NOTE: cellulose media cartridges. If your cartridge seems to disintegrate, or has a musty or moldy odor, switch to a synthetic media cartridge or consult the manufacturer. NOTE: Estimated capacity tested at given flow rate using 2 ppm free available chlorine to 0.5 ppm breakthrough and 3 ppm chloramine to 0.5 ppm breakthrough. NOTE: Increased flow rates may result in less effective chlorine reduction.

65 COCONUT CARBON CARTRIDGES COCONUT BASED CARBON BLOCK CARTRIDGES CEP-10E CCBC-10 Coconut based carbon block cartridges are highly effective at reducing unwanted taste & odor and chlorine taste & odor from potable drinking water, and they are equally effective at reducing fine sediment.* Coconut based carbon block cartridges are manufactured using a patented process and are made from a water-washed, coconut-carbon formulation. This process and media yield a cartridge with high chlorine taste & odor reduction capacity. These cartridges are protected by Endurawrap, a uniquely formulated polyolefin bilaminate pre-filter, designed to significantly increase the useful life of the cartridge by trapping sediment that typically plugs carbon block cartridges. They are an ideal choice for a wide range of residential, food service, commercial and industrial applications. They also make excellent polishing filters or prefilters in applications requiring fine filtration and high capacity. * Based on manufacturer s internal testing.

66 COCONUT CARBON CCBC " x 9 3 4" (73 mm x 248 mm) gpm ( Lpm) CEP-10E 2 7 8" x 9 3 4" (73 mm x 248 mm) gpm ( Lpm) >20,000 1 gpm 3.8 Lpm) >5,000 1 gpm 3.8 Lpm) Filter Media End Caps Inner/Outer Wraps Netting Gaskets Temperature Rating Water-Washed Coconut Based Carbon (CCBC-10) Acid-Washed Coconut Based Carbon (CEP-10E) Polypropylene Polyolefin Polyethylene Buna-N ºF ( ºC) WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. U.S. Patent No. 5,976,432 & 5,823,668 Tested and Certified by NSF International to NSF/ANSI Standard 42 for material requirements only Pentair Filtration, Inc. Printed in USA MR

67 EP SERIES CARTRIDGES EP SERIES CARBON-BRIQUETTE CARTRIDGES EP-20 EP-10 EP-BB EP- 20BB EP Series carbon briquette cartridges are manufactured using a patented process that yields a cartridge with a nominal 5-micron filtration rating, high dirt-holding capacity. A high porosity design helps prevent the cartridge from plugging before its adsorption capacity is exhausted, maximizing the utilization of the carbon while maintaining low pressure drop. These cartridges are protected by Endurawrap, a uniquely formulated polyolefin bilaminate pre-filter, designed to significantly increase the useful life of the cartridge by trapping sediment that typically plugs carbon block cartridges. EP Series cartridges are manufactured entirely from FDAcompliant materials making them an ideal choice for a wide range of residential, food service, commercial and industrial applications. * Based on manufacturer s internal testing.

68 EP SERIES EP " x 9 3 4" (73 mm x 248 mm) gpm ( Lpm) EP " x 20" (73 mm x 508 mm) gpm ( Lpm) > gpm 3.8 Lpm) >12,000 2 gpm 7.6 Lpm) EP-30 5 EP-40 5 EP-BB 4 5 8" x 9 3 4" (118 mm x 248 mm) gpm ( Lpm) EP20-BB 4 5 8" x 20" (118 mm x 508 mm) gpm ( Lpm) Filter Media End Caps Inner/Outer Wraps Netting Gaskets Temperature Rating Bonded PAC Polypropylene Polyolefin Polyethylene Buna-N ºF ( ºC) >22,000 2 gpm 7.6 Lpm) >40,000 4 gpm 15.1 Lpm) This EP-10, EP-20, EP-BB and EP-20BB are Tested and Certified by NSF International to NSF/ANSI Standard 42 for material requirements only. WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. NOTE: The EP cartridges will contain a very small amount of carbon fines (very fine black powder) and a new cartridge after installation should be flushed with sufficient water to remove the fines from your water system before using the water. NOTE: Micron ratings based on 85% or greater removal of given particle size. Data obtained from actual particle counts using AC Fine Test Dust and Latex spheres. NOTE: Estimated capacity using 2ppm free available chlorine (FAC) at continuous flow with greater than 90% reduction. U.S. Patent No. 5,976,432 & 5,823, Pentair Filtration, Inc. Printed in USA MR

69 ELPC SERIES CARTRIDGES ELPC-30 ELPC SERIES ELECTROPLATING CARBON CARTRIDGES The ELPC Series is a premium line of activated carbon filter cartridges specifically designed for electroplating solutions. They represent the best technology available in cartridge filtration for use in a wide range of electroplating applications. The unique technology used to manufacture this product ensures that there is no bleeding of carbon fines into the plating bath. In addition, the carbon that is used is an ultra-clean, highly purified carbon to ensure that sulfur is not leached into the plating bath. ELPC Series products have a 10-micron nominal rating with superior dirt-holding ability. The fibrous physical structure created by our proprietary Fibredyne technology produces a unique block with true depth filtration capability which allows for maximum treatment with minimal pressure drop through the cartridge. ELPC-10 ELPC-20

70 ELPC SERIES ELPC-10 ELPC-20 ELPC " x 10"* (73mm x 248mm) 2 7 8" x 20" (73mm x 508mm) 2 7 8" x 30" (73mm x 762mm) Filter Media End Caps Netting Gaskets Bonded PAC Polypropylene Polyethylene Santoprene gpm ( Lpm) gpm ( Lpm) gpm ( Lpm) *Designed for use in spring-loaded industrial housings. This will not fit a standard PENTEK plastic 10-inch housing. WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the unit. NOTE: Cartridges will contain a very small amount of carbon fines (very fine black powder). After installation, a new cartridge should be flushed with sufficient water to remove all traces of fines prior to using the water. NOTE: Micron ratings based on 85% or greater removal of given particle size. Estimated capacity using 2ppm free available chlorine at 0.5 ppm breakthrough. 40 F-180 F (4.4 C-82.2 C) 40 F-180 F (4.4 C-82.2 C) 40 F-180 F (4.4 C-82.2 C) 2008 Pentair Filtration, Inc. Printed in USA JL08

71 EPM SERIES CARTRIDGES EPM SERIES MODIFIED EPSILON CARBON-BRIQUETTE CARTRIDGES EPM-20 EPM- 20BB EPM Series cartridges are a modified version of our EP Series cartridge. An economical price makes this cartridge suitable for taste, odor and chlorine taste & odor reduction, as well as sediment filtration.* EPM Series cartridges are manufactured using a patented process that yields a cartridge with a nominal 10-micron filtration rating, high porosity and chlorine taste & odor reduction. The high porosity design helps prevent the cartridge from plugging before its adsorption capability is exhausted, maximizing the utilization of the carbon while maintaining low pressure drop. These cartridges are protected by Endurawrap, a uniquely formulated polyolefin bilaminate pre-filter, designed to significantly increase the useful life of the cartridge by trapping sediment that typically plugs carbon block cartridges. EPM Series cartridges are manufactured entirely from FDAcompliant materials making them an ideal choice for a wide range of residential, food service, commercial and industrial applications. * Based on manufacturer s internal testing. EPM-10 EPM-BB

72 EPM SERIES NOTE: Micron ratings based on 85% or greater removal of given particle size. Data obtained from actual particle counts, using AC Fine Test Dust at 1 gpm. Estimated capacity using 2.0 ppm free available chlorine (FAC) at 0.5 ppm break through. EPM " x 9 3 4" (73 mm x 248 mm) gpm ( Lpm) EPM " x 20" (73 mm x 508 mm) gpm ( Lpm) EPM-BB 4 5 8" x 9 3 4" (118 mm x 248 mm) gpm ( Lpm) EPM-20BB 4 5 8" x 20" (118 mm x 508 mm) gpm ( Lpm) Filter Media End Caps Outer Wrap Netting Gaskets Temperature Rating Bonded PAC Polypropylene Polyolefin Polyethylene Buna-N ºF ( ºC) >3,000 1 gpm 3.8 Lpm) >6,000 2 gpm 7.6 Lpm) >15,000 2 gpm 7.6 Lpm) >30,000 4 gpm 15.1 Lpm) Tested and Certified by NSF International to NSF/ANSI Standard 42 for material requirements only. NOTE: Performance capacity depends on system design, flow rate and certain other application conditions. NOTE: When greater chlorine taste & odor reduction is needed, use the standard EP series blocks. WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. NOTE: EPM-Series cartridges will contain a very small amount of carbon fines (very fine black powder). After installation follow the instructions for flushing the cartridge to remove the fines before using the water. You should run (flush) the tap at least 20 seconds prior to using water for drinking or cooking purposes. This is particularly important if the tap has not been used daily. U.S. Patent No. 5,976,432 & 5,823, Pentair Filtration, Inc. Printed in USA MR

73 GAC SERIES CARTRIDGES GAC-20BB GAC SERIES GRANULAR ACTIVATED CARBON CARTRIDGES GAC Series cartridges effectively reduce unwanted tastes and odors, including chlorine taste & odor from your drinking water.* They are designed to allow maximum contact between the water and carbon, ensuring optimal adsorption. The construction of the cartridge allows water to enter at one end and pass through the entire length of the carbon bed before exiting the other end of the cartridge, while an internal expansion pad minimizes channeling or bypass. Before the water exits the cartridge, a 20-micron post filter helps reduce carbon fines and other suspended particles from the filtered water. The post-filter is permanently fastened to an innovative support basket ensuring that it is firmly secured and eliminating any potential for bypass. GAC Series cartridges are available in a variety of sizes and flow rates, and effectively provide good general-purpose drinking water filtration. * Based on manufacturer s internal testing. GAC-20 GAC-5 GAC-BB

74 GAC SERIES 80 Approximate Net Pressure Drop psi (Bar) GAC-20 GAC-10 GAC-5 GAC-BB GAC-20BB (1.9) (7.6) (15.1) (22.7) (30.3) Flow Rate gpm (Lpm) 10.0 (37.9) GAC " x 4 7 8" (73 mm x 124 mm) gpm ( Lpm) gpm 1.9 Lpm) GAC " x 9 3 4" (73 mm x 248 mm) gpm ( Lpm) 5, gpm 3.8 Lpm) GAC " x 20" (73 mm x 508 mm) gpm ( Lpm) 10, gpm 7.6 Lpm) GAC-BB 4 1 2" x 9 3 4" (114 mm x 248 mm) gpm ( Lpm) 12, gpm 7.6 Lpm) GAC-20BB 4 1 2" x 20" (114 mm x 508 mm) gpm ( Lpm) 25, gpm 15 Lpm) Filter Media End Caps Post-Filter Outer Casing Expansion Pad Granular Activated Carbon Polystyrene Spun Polypropylene Polystyrene Polypropylene The GAC-10 and GAC-20BB are Tested and Certified by NSF International to NSF/ANSI Standard 42 for material requirements only. Buna-N (top) Gasket Santoprene (bottom) Temperature Rating ºF ( ºC) WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. NOTE: A drinking water cartridge may contain carbon fines (very fine black powder). After installation and before using the water, follow the instructions for flushing the cartridge to remove fines. NOTE: It is recommended that you flush for 20 seconds prior to using the water for drinking or cooking purposes. NOTE: Chlorine Reduction is estimated capacity using 2ppm free available chlorine (FAC) at continuous flow with greater than 75% reduction Pentair Filtration, Inc. Printed in USA JE

75 STRAP FLOPLUS BAND SERIES BAG CARTRIDGES FILTER HOUSINGS FloPlus-20 FloPlus-20BB FloPlus Series Modified Molded Carbon Block Cartridges FloPlus-10BB FloPlus-10 FloPlus cartridges utilize a revolutionary new technology that significantly enhances the traditional Fibredyne product, making it possible to obtain cyst reduction in a cartridge that functions like a nominal 10-micron cartridge. This product boasts extremely low pressure drops and high flow rates comparable to 10-micron (very open) carbon cartridges. Its efficiency is so high that a 0.5-micron rating is possible, which means that cysts and very small particles can be removed to create cleaner, safer water. This product is ideal for applications where pressure drop and low flow have been chronic problems in the past, as well as whole house water treatment with the addition of cyst reduction. However, it will address the needs of any end user looking for a product that offers high flow, low pressure drop, infrequent cartridge changes and cyst-free water. FEATURES BENEFITS APPLICATIONS

76 FloPlus Modified Molded Carbon Block Cartridges Approximate Net Pressure Drop psi FloPlus 10 FloPlus 10BB FloPlus 20BB FloPlus 20 Pressure Drop psi FloPlus Cyst Reduction Carbon Block (NEW!) gpm 2 gpm Standard Cyst Reduction Carbon Block Flow Rate gpm Gallons Per Minute gpm Cartridge Specifications and Performance Data Maximum Micron Rating Model Dimensions (Nominal)* Initial ΔP Flow Rate (gpm)* Chlorine Taste & Odor Flow Rate (gpm)* FloPlus " x 9 3 4" (73mm x 248mm) gpm ( Lpm) >10,000 1 gpm (>37, Lpm) FloPlus " x 20" (73mm x 508mm) gpm ( Lpm) >20,000 2 gpm (>75, Lpm) FloPlus-10BB 4 5 8" x 9 3 4" (118mm x 248mm) gpm ( Lpm) >25,000 2 gpm (>94, Lpm) FloPlus-20BB 4 5 8" x 20" (118mm x 508mm) *Based on manufacturer s internal testing. 0.5 Materials of Construction Filter Media Bonded PAC End Caps Polypropylene Netting Polyethylene Gaskets Santoprene Temperature Rating 40 F to 180 F (4.4 C to 82.2 C) NOTE: Performance capacity depends on system design, flow rate and certain other application conditions. Certain states require system registration or certification for health-related reduction claims. WARNING: For drinking water applications, do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Sheboygan, Wisconsin gpm ( Lpm) NOTE: A drinking water cartridge may contain carbon fines (very fine black powder). After installation and before using the water, follow the instructions for flushing the cartridge to remove fines. NOTE: It is recommended that you run the tap for 20 seconds prior to using the water for drinking or cooking purposes. >50,000 4 gpm (>189, Lpm) The FPS-10 with the FloPlus 10, FPS-20 with the FloPlus 20, FPS-10BB with the FloPlus 10BB and the FPS-20BB with the FloPlus 20BB are Tested and Certified by NSF International to NSF/ANSI Standard 53 for the reduction of Cysts Pentair Filtration, Inc FE08

77 NCP SERIES CARTRIDGES NCP SERIES NON-CELLULOSE CARBON-IMPREGNATED PLEATED CARTRIDGES NCP-20 NCP-10 NCP-BB NCP- 20BB NCP Series cartridges are constructed from a carbonimpregnated non-cellulose media. They offer sediment-filtration, as well as taste, odor and chlorine taste and odor reduction in one cartridge. Unlike cellulose cartridges, NCP Series cartridges are resistant to bacterial attack allowing them to be used for municipal and nonchlorinated water applications. Pleats provide additional surface area for high dirt-loading capacity, while maintaining minimal pressure drop. This combination of a pleated polyester media and carbon filtration produces an outstanding filter cartridge with extended service life. NCP Series cartridges are excellent polishing filters, closed loop streams and are ideal for post reverse osmosis and well water applications.

78 NCP SERIES NCP-20 NCP-10 NCP- 20BB NCP-BB NCP " x 9 3 4" (64 mm x 248 mm) gpm ( Lpm) NCP-BB 4 1 2" x 9 3 4" (114 mm x 248 mm) gpm ( Lpm) NCP " x 20" (64 mm x 508 mm) gpm ( Lpm) NCP-20BB 4 1 2" x 20" (114 mm x 508 mm) gpm (< Lpm) gpm 3.8 Lpm) gpm 7.6 Lpm) gpm 7.6 Lpm) gpm 15 Lpm) Filter Media End Caps Netting Core Temperature Rating Pleated Carbon-Impregnated Polyester Vinyl Plastisol Polypropylene Polypropylene ºF ( ºC) WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system Pentair Filtration, Inc. Printed in USA MR

79 RFC SERIES CARBON CARTRIDGES RFC SERIES RADIAL FLOW CARBON CARTRIDGES RFC-20 RFC-BB RFC20-BB RFC Series cartridges are constructed with a 70-micron porous polyethylene outer shell and durable polypropylene end caps. The inch outer diameter cartridges have a polypropylene core and the inch outer diameter cartridges incorporate a spun polypropylene core. Sandwiched between the outer shell and the core is a bed of granular activated carbon (GAC). The unique radial flow design offers the benefits of granular activated carbon (GAC) filtration, such as low pressure drop, while at the same time significantly reducing the release of carbon fines commonly associated with GACstyle cartridges. RFC Series cartridges are available in a wide variety of sizes and are ideal for point-of-entry (POE) and other high flow rate applications. * Based on manufacturer s internal testing.

80 RFC SERIES RFC " x 9 3 4" (70 mm x 248 mm) gpm ( Lpm) > gpm 3.8 Lpm) RFC " x 20" (70 mm x 508 mm) gpm ( Lpm) > gpm 7.6 Lpm) RFC-BB 4 1 2" x 9 3 4" (114 mm x 248 mm) gpm ( Lpm) >35,000 2 gpm 7.6 Lpm) RFC20-BB 4 1 2" x 20" (114 mm x 508 mm) gpm ( Lpm) >70,000 4 gpm 15.1 Lpm) Filter Media Outer Shell End Caps Gasket Inner Wraps/Core Temperature Rating Granular Activated Carbon Polyethylene Polypropylene Buna-N Polypropylene ºF ( ºC) The RFC-93 is Tested and Certified by NSF International to NSF/ANSI Standard 42 for material requirements only. WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. NOTE: The granular activated carbon cartridges will contain a very small amount of carbon fines (very fine black powder). After installation, a new cartridge should be flushed with sufficient water to remove all traces of the fines from your water system before using the water. Each time you use your filtered water tap for drinking or cooking purposes it is recommended that you run (flush) the tap for at least 20 seconds prior to using water. This is particularly important if the water tap has not been used daily Pentair Filtration, Inc. Printed in USA JL

81 SCBC-10 CARTRIDGE SCBC-10 ANTI MICROBIAL CARBON BLOCK CARTRIDGE Cryptosporidium, Giardia, Enamoeba,Toxoplasma The SCBC-10 cartridge contains a highly effective anti microbial compound with controlled silver release that provides long lasting protection of the activated carbon surfaces from bio fouling bacteria. The SCBC-10 cartridge is highly effective at reducing unwanted taste & odor and chlorine taste & odor from potable drinking water. With a nominal 0.5 micron rating, it is equally effective at reducing fine sediment and cysts such as Cryptosporidium and Giardia. The SCBC-10 cartridge is manufactured using a patented process and is made from activated carbon that is tested for purity and performance prior to manufacture. This process and media yields a cartridge with high chlorine taste & odor reduction capacity. This cartridge is protected by Endurawrap, a uniquely formulated polyolefin bilaminate pre filter, designed to significantly increase the useful life of the cartridge by trapping sediment that typically plugs carbon block cartridges. This is an ideal choice for a wide range of residential, food service, commercial and industrial applications. They also make excellent polishing filters or pre filters in applications requiring fine filtration and high capacity. SCBC-10

82 SCBC-10 SCBC " x 9 3 4" (73mm x 248mm) gpm ( Lpm) >20,000 1 gpm (>75, Lpm) Filter Media End Caps Inner/Outer Wraps Netting Gaskets Temperature Rating Silver Content Bonded PAC Polypropylene Polyolefin Polyethylene Polyolefin ºF ( ºC) 0.05% by weight NOTE: Performance capacity depends on system design, flow rate and certain other application conditions. Certain states require system registration or certification for health related contaminant reduction claims. WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. NOTE: Cartridge may contain a very small amount of carbon fines (very fine black powder) and a new cartridge after installation should be flushed with sufficient water to remove all traces of the fines from your water system before using the water. NOTE: Nominal micron ratings based on 85% or greater removal of given particle size. NOTE: The SCBC-10 cartridge is capable of reducing 99.95% of Cryptosporidium and Giardia cysts. Data obtained from actual test dust and particle counts using Latex spheres. Estimated capacity using 2ppm free available chlorine (FAC) with greater than 90% reduction. U.S. Patent No. 5,976,432 & 5,823,668 EPA Est WI Pentair Filtration, Inc. Printed in USA MR

83 TSGAS CARTRIDGE TSGAC SPECIALTY GRANULAR ACTIVATED CARBON/PHOSPHATE CARTRIDGE TSGAC cartridges contain granular activated carbon to effectively reduce unwanted taste and odor and chlorine taste and odor, as well as phosphate crystals to reduce rust stains and scale deposits.* The construction of the cartridge allows water to enter at one end and pass through the entire length of the carbon bed before exiting the other end of the cartridge. An internal expansion pad minimizes channeling or bypass. This design allows for maximum contact between the water and carbon, ensuring maximum adsorption. Before the water exits the cartridge, a 20-micron post filter helps remove carbon fines and other suspended particles from the filtered water. The post filter is permanently fastened to an innovative support basket ensuring that it is firmly secured and eliminating any potential for bypass. TSGAC cartridges provide superior performance and outstanding protection for your water lines, fixtures, major appliances and commercial equipment. * Based on manufacturer s internal testing. TSGAC-10

84 TSGAC CARTRIDGE TSGAC " x 9 3 4" (73 mm x 248 mm) gpm ( Lpm) > gpm 3.8 Lpm) Filter Media End Caps Post-Filter Outer Casing Expansion Pad Granular Activated Carbon Hexametaphosphate Crystals Polystyrene Spun Polypropylene Polystyrene Polypropylene Buna-N (top) Gasket Santoprene (bottom) Temperature Rating ºF ( ºC) WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. NOTE: A drinking water cartridge may contain carbon fines (very fine black powder). After installation and before using the water, flush the cartridge for 5 minutes to remove fines. NOTE: It is recommended that you run the tap for 20 seconds prior to using the water for drinking or cooking purposes. The TSGAC-10 is Tested and Certified by NSF International to NSF/ANSI Standard 42 for material requirements only Pentair Filtration, Inc. Printed in USA MR

85 CRE-1 CARTRIDGE CRE-1 CERAMIC CARTRIDGE CRE-1 cartridges are manufactured from a sintered ceramic filtration media. They are designed and tested for the reduction of Cryptosporidium and Giardia cysts, and are ideal for fine sediment filtration applications. The fine ceramic media will effectively trap dirt, sediment and cysts down to 1-micron in diameter. A proper fit is ensured and water bypass is prevented through the use of a knife-edge seal. CRE-1 cartridges are easily cleaned with water and a damp cloth, sponge or stiff nylon brush. They can be cleaned several times until the diameter at the smallest point is 1 1 2" or the circumference is 4 3 4", extending cartridge life. NOTE: Not for residential sale in the state of California.

86 CRE-1 CRE-1 1 " x Filter Media End Caps Gasket Temperature Rating NOTE: Performance depends on system design, flow rate, feed water quality and certain other application conditions. Certain states require system registration or certification prior to sale if health-related contaminant reduction claims are made. Not for residential sale in the state of California. NOTE: Only a thin layer of ceramic is removed with each cleaning. It is not necessary to clean the cartridge until the original color is restored as water in some locations may stain or discolor the ceramic. Good hygiene and housekeeping practices should always be used when cleaning the CRE-1 cartridge. HANDLE CARTRIDGE WITH CARE! Sharp blows, dropping or freezing can cause cracks in the ceramic. If the cartridge should be cracked or frozen, discard the damaged cartridge and replace it with a new cartridge. WARNING: Do not use where water is microbiologically unsafe or with water of unknown quality without adequate disinfection before or after the system. Cartridge specifically designed for sediment filtration and the reduction of Giardia and Cryptosporidium cysts, not to kill or filter bacteria.

87 CW/WP SERIES CARTRIDGES CW/WP SERIES POLYPROPYLENE WOUND CARTRIDGES CW and WP Series cartridges are manufactured from a durable polypropylene cord that is wound around a rigid polypropylene core. They are an economical solution to reduce fine sediment, including sand, silt, rust and scale particles. CW cartridges are very economical and wound in a standard pattern around the core. They are available in 10, 30 and 50-micron ratings. WP Series cartridges are wound in a precise pattern around the core providing greater surface area. The result is higher dirt-loading capacity and greater efficiency than standard wound cartridges like the CW. Both of these string-wound cartridge styles are capable of withstanding temperatures up to 165ºF (73.9ºC), and will accommodate flow rates between 7 and 10 GPM with minimal pressure drop. CW and WP Series cartridges are suitable for a wide variety of sediment filtration applications, including municipal and well water as well as many industrial fluids.

88 CW/WP SERIES CW-F 2 1 4" x 9 7 8" (60 mm x 251 mm) 10 <1 10 gpm (< Lpm) CW-MF 2 1 4" x 9 7 8" (60 mm x 251 mm) 30 <1 10 gpm (< Lpm) CW " x 9 7 8" (60 mm x 251 mm) 50 <1 10 gpm (< Lpm) WP " x 9 7 8" (60 mm x 251 mm) 5 < gpm (< Lpm) WP " x 9 7 8" (60 mm x 251 mm) 30 < gpm (< Lpm) Filter Media Core Temperature Rating Polypropylene Fiber Cord Polypropylene ºF ( ºC) WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

89 dgd series cartridges DGD SERIES DUAL-GRADIENT DENSITY CARTRIDGES Manufactured from pure 100% polypropylene Designed for purity and chemical compatibility Spun fibers form a true gradient density from outer to inner surfaces DGD Series cartridges are manufactured from 100% pure polypropylene and are sized for use in our Big Blue filter housings. DGD Series cartridges are designed for purity and will not impart taste, odor or color to the liquid being filtered. Additionally, the polypropylene construction provides superior chemical resistance and is not prone to bacterial attack. The DGD Series' advanced design combines selective final filtration with appropriate pre-filtration to achieve up to three times the dirt-holding capacity of similar size sediment cartridges and even greater capacity than standard spun or string-wound cartridges. This performance enhancement is achieved by combining two separate gradient layers in one filter. The larger diameter of the pre-filter reduces the particle load to the post filter, allowing it to operate at higher velocities. The effective filter depth is increased to a full 233% of standard spun-polypropylene or string-wound filters. This increased depth provides for very high particulate reduction efficiencies and added loading capacity. The unique design and performance characteristics of the DGD Series cartridges make them an excellent choice for all residential, rural, municipal and commercial applications.

90 DGD SERIES Dual-Gradient Density Cartridges Cartridge Specifications and Performance Data DGD-2501 DGD-5005 DGD-7525 Materials of Construction Filter Media Model Maximum Dimensions Micron Rating* (nominal) DGD DGD DGD Temperature Rating 4 1 2" x 10" (114 mm x 254 mm) 4 1 2" x 10" (114 mm x 254 mm) 4 1 2" x 10" (114 mm x 254 mm) 4 1 2" x 20" (114 mm x 508 mm) 4 1 2" x 20" (114 mm x 508 mm) 4 1 2" x 20" (114 mm x 508 mm) * Based on manufacturer's internal testing Polypropylene ºF ( ºC) Pre-filter: 25 Post filter: 1 Pre-filter: 50 Post filter: 5 Pre-filter: 75 Post filter: 25 Pre-filter: 25 Post filter: 1 Pre-filter: 50 Post filter: 5 Pre-filter: 75 Post filter: 25 WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Initial P Flow Rate (gpm) <1 10 gpm (< Lpm) <1 10 gpm (< Lpm) <1 10 gpm (< Lpm) <1 20 gpm (< Lpm) <1 20 gpm (< Lpm) <1 20 gpm (< Lpm) Tested and Certified by NSF International to NSF/ANSI Standard 42 for material requirements only. 502 Indiana Avenue P.O. Box 1047 Sheboygan, Wisconsin Customer Service: Fax: supportspecialist@pentekfiltration.com International: Fax: international@pentekfiltration.com 2006 Pentair Filtration, Inc. Printed in USA MR

91 ECP SERIES PLEATED CELLULOSE POLYESTER CARTRIDGES ECP1-20 ECP20-20BB ECP SERIES PLEATED CELLULOSE POLYESTER CARTRIDGES ECP Series cartridges are manufactured from a special formulation of resin-impregnated cellulose and polyester fibers. This unique blend of materials provides a higher wet strength than regular cellulose cartridges. It also provides high flow rates and dirtholding capacity, while maintaining extremely low pressure drop. The media is pleated around a polypropylene core for added strength and the ends are immersed in a thermo-setting vinyl plastisol. Embedding and sealing each end of the pleat block in this fashion fuses the components together forming a unified endcap and gasket. ECP Series cartridge endcaps feature a color-coding system for easy identification of micron ratings: Tan (1-micron), White (5-micron), Blue (20-micron), Yellow (50-micron). ECP cartridges contain more media surface area than most competitive cartridges. The standard 10-inch ECP cartridge contains six square feet of media, where most cartridges contain only 4.5 square feet. Other available ECP cartridge sizes contain the following amount of media: ECP50-BB ECP5-10

92 ECP SERIES Media Core Endcaps Temperature Rating Cellulose Polyester Polypropylene Vinyl Plastisol WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. ECP1-10 Tan 2 5 " x ECP5-10 White 2 5 " x ECP20-10 Blue 2 5 " x ECP50-10 Yellow 2 5 " x ECP1-20 Tan ECP5-20 White ECP20-20 Blue ECP50-20 Yellow ECP1-BB Tan 4 1 2" x ECP5-BB White 4 1 2" x ECP20-BB Blue 4 1 2" x ECP50-BB Yellow 4 1 2" x ECP1-20BB Tan ECP5-20BB White ECP20-20BB Blue ECP50-20BB Yellow

93 FILTRATION COMPONENTS Gradient Density Cartridges GD/GDA Series The new GD and GDA Series of cartridges are manufactured in the USA from 100% pure polypropylene and are sized for use in the PENTEK 10" and 20" Big Blue housings. GD and GDA Series are designed for purity and will not impact taste, odor and color and provide superior chemical resistance and are not prone to bacterial attack. Two unique layers provide up to three times the dirt-holding capacity than pleated, string-wound and standard spun polypropylene cartridges provide. A larger outer pre-filter reduces the partial load to the inner post filter allowing the cartridge to operate at higher velocities and lower pressure drop. The effective filter depth is increased over 200% of string-wound and standard spun-polypropylene cartridges for extended life, performance and reliability. The design and performance characteristics of the GD and GDA Series Cartridges make them an excellent choice for all residential, rural, municipal, industrial, and commercial applications. Typical Applications Well Water Hotel/Motel Restaurants City Water Laboratories Schools Homes Laundromats Factories Cafeterias

94 FILTRATION COMPONENTS Gradient Density Cartridges GD/GDA Series Features and Benefits 100% polypropylene filtration media for superior purity without affecting taste, odor or color. Two clearly visible gradient layers ensure higher efficiency and improved performance. Micron ratings for virtually any application (75-25 for outer layer, inner layer). GDA Series has polypropylene inner support core for added strength and unimpeded flow. Polypropylene filter media resists chemicals and bacterial attack. Up to three times the dirt-holding capacity of similar-sized pleated, string-wound and spunpolypropylene cartridges. Effectively reduces sediment as a pre-filter to softener and automatic filter systems. Saves space all-in-one, two-layer cartridge eliminates the need for additional filter canisters. Performance Flow Rate Characteristics Pressure Drop in PSI Flow Rate (Lpm) Pressure Drop (Bar) Materials of Construction Filter Media Polypropylene Temperature Rating ºF ( ºC) Cartridge Specifications and Performance Data GD-7520-BB GD-5010-BB GD BB GD-2501-BB Flow Rate in Gallons Per Minute GD BB GDA-7505-BB GD BB GDA-5001-BB 0.14 GDA BB GDA BB GDA BB GDA BB Model Maximum Dimensions Micron Rating* Micron Size Initial ΔP Flow Rate (gpm) GD-7520-BB 4-1/2" x 9-7 8" (114 mm x 251 mm) Nominal Outside 75 - Core 20 < gpm (< Lpm) GD-5010-BB 4-1/2" x 9-7 8" (114 mm x 251 mm) Nominal Outside 50 - Core 10 <2 10 gpm (< Lpm) GD-2501-BB 4-1/2" x 9-7 8" (114 mm x 251 mm) Nominal Outside 25 - Core 1 < gpm (< Lpm) GD BB 4-1/2" x 20" (114 mm x 508 mm) Nominal Outside 75 - Core 20 <3 10 gpm (< Lpm) GD BB 4-1/2" x 20" (114 mm x 508 mm) Nominal Outside 50 - Core 10 <4 10 gpm (< Lpm) GD BB 4-1/2" x 20" (114 mm x 508 mm) Nominal Outside 25 - Core 1 < gpm (< Lpm) GDA-7505-BB 4-1/2" x 9-7 8" (114 mm x 251 mm) Absolute Outside 75 - Core 5 < gpm (< Lpm) GDA-5001-BB 4-1/2" x 9-7 8" (114 mm x 251 mm) Absolute Outside 50 - Core 1 <9 10 gpm (< Lpm) GDA BB 4-1/2" x 9-7 8" (114 mm x 251 mm) Absolute Outside 25 - Core 0.5 < gpm (< Lpm) GDA BB 4-1/2" x 20" (114 mm x 508 mm) Absolute Outside 75 - Core 5 < gpm (< Lpm) GDA BB 4-1/2" x 20" (114 mm x 508 mm) Absolute Outside 50 - Core 1 <18 10 gpm (< Lpm) GDA BB 4-1/2" x 20" (114 mm x 508 mm) Absolute Outside 25 - Core 0.5 <21 10 gpm (< Lpm) *Based on manufacturer s internal testing. WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Tested and Certified by NSF International to NSF/ ANSI Standard 42 for material requirements only North Glen Park Road Milwaukee, WI Tel: Fax: Customer Care: Pentair Residential Filtration, LLC Rev A AU10

95 MICROGUARD SERIES CARTRIDGES MICROGUARD SERIES MEMBRANE FILTER CARTRIDGES MG-10T MG-10MCB The MicroGuard membrane filters provide reliable bacteria and protozoan cyst reduction for safer and cleaner drinking water without incorporating chemicals into the media or adding chemicals to the filtered water. The MicroGuard carbon block membrane cartridge, MG-10MCB, is uniquely designed with integral carbon block and sediment pre-filtration for the reduction of chlorine taste and odor and for providing extended life of the internal membrane element. This cartridge has 2.5 times greater filtration surface area than some anti-microbial carbon blocks and operates at a higher flow rate with lower pressure drop. This makes the MG-10MCB ideal for Point-of-Use (POU) applications. The MicroGuard cartridges do not require USEPA registration and their effectiveness is not susceptible to common substances normally found in some waters, e.g., hydrogen sulfide (H 2 S), natural organic matter (NOM) and total dissolved solids (TDS). The MicroGuard triple-element cartridge, MG-10T, is uniquely constructed with three membrane elements integrally sealed into one common cartridge design. This unique design allows for higher flow rates and longer life while still providing bacteria and cyst reduction, and is ideal for applications up to five gallons-per-minute. The life of the MG-10T can be extended using PENTEK carbon block or sediment pre-filtration options. *U.S. Patent No. 5,240,862 EPA Est. No WI-001 Not certified for sale in California, Iowa, Massachusetts and Wisconsin. NOTE: These cartridges are not intended for converting wastewater or raw sewage into drinking water.

96 FEATURES AND BENEFITS MG-10MCB PENTEK and Standard. MG-10T PENTEK and Standard. pressure) to water main breaks, water treatment plant failure during floods and power outages hydrogen sulfide (H 2 S), natural organic matter (NOM) and total dissolved solids (TDS) MG-10MCB MG-10T oral care oral care food preparation food preparation hand washing hand washing Not certified for sale in California, Iowa, Massachusetts and Wisconsin. Note: These cartridges are not intended for converting wastewater or raw sewage into drinking water.

97 MG-CCBR MICROGUARD CARTRIDGE MG-CCBR MICROGUARD MEMBRANE FILTER CARTRIDGE The MG-CCBR Microguard membrane filter cartridge provides combined carbon block and sediment pre-filtration for extended life and chlorine taste & odor reduction as well as lead, mercury, cyst, bacteria and VOC reduction. This cartridge utilizes patented* highly asymmetric polyethersulfone membrane with proprietary hydrophilic formulation for immediate wetting and high flow. The MG-CCBR has a single openended gasket seal and fits all 10" standard and 3G PENTEK filter housings. MG-CCBR *U.S. Patent No. 5,240,862 EPA Est. No WI-001 Not certified for sale in California, Iowa, Massachusetts and Wisconsin NOTE: These cartridges are not intended for converting wastewater or raw sewage into drinking water.

98 MG-CCBR MICROGUARD main breaks, water treatment plant failure during floods and power outages MG-CCBR 2 7 8" x 9 3 4" (73mm x 248mm) gpm ( L/min) Polyethersulfone Polystyrene, epoxy resin Polypropylene Polyolefin Santoprene Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

99 OAC-20BB CARTRIDGE OIL ADSORBING CARTRIDGE OAC-20BB The OAC-20BB filter cartridge is made from modified cellulose-based filter media which is processed into sheets and assembled into cartridges for use in standard 20-inch Big Blue filter housings. Features 90 percent of total hydrocarbons removed in a single pass dispersed oils Dimensions Outside Diameter of its own weight, with no release of removed hydrocarbons Applications bilge water End Caps Center Core Outer Net Area Weight Chemical Notification # PVC Plastisol Natural Polypropylene Polyethylene Installation Certain applications may require pre-filtration. Change-Out Frequency Change-out frequency will depend on the oil burden in the application. Because no appreciable increase in pressure drop is observed during service life, the filter must be changed when its adsorption capacity is exhausted.

100 OAC-20BB Miscellaneous Liquids Water 1.0 Kerosene Turpentine 0.9 Fuel Oil and Diesel Oil Crankcase Oil - Automobile Lubricating Oils Transmission Oils - Automobile Transmission Gear Lubricants Other Oils Castor Oil 9000 Chinawood Coconut Cod Corn Cylinder Olive Palm Peanut 0.92 Quencing Extreme Viscose Whale The Oil Adsorbing cartridge typically reduces hydrocarbon contamination up to percent in a single pass. Lower outlet levels of hydrocarbons can be achieved by connecting cartridges in series. Higher flow rates also can be achieved by connecting cartridges in parallel. Hydrocarbon-adsorbing capacity: contaminant. On this basis, the table below provides expected life data in hours or gallons at several contaminant levels NOTE: DISPOSAL: additional information.

101 P SERIES CARTRIDGES P SERIES SPUN-BONDED POLYPROPYLENE CARTRIDGES P Series cartridges are manufactured from pure 100% polypropylene fibers. The fibers have been carefully spun together to form a true gradient density from outer to inner surfaces. P Series cartridges are designed for purity. They will not impart taste, odor or color to the liquid being filtered when used within the recommended temperature limit. Additionally, the polypropylene construction provides superior chemical resistance and is not prone to bacterial attack. The coreless strength of the cartridges is achieved by sintering the many fibers into a solid matrix. P Series cartridges are available in a wide array of sizes and micron ratings to accommodate all of your filtration needs.

102 P SERIES P " x 4 7 8" (60 mm x 124 mm) gpm (< Lpm) P " x 9 3 4" (60 mm x 248 mm) gpm (< Lpm) P " x 9 3 4" (60 mm x 248 mm) gpm (< Lpm) P " x 9 3 4" (60 mm x 248 mm) gpm (< Lpm) P " x 20" (60 mm x 508 mm) gpm (< Lpm) P " x 20" (60 mm x 508 mm) gpm (< Lpm) P " x 20" (60 mm x 508 mm) gpm (< Lpm) P " x 30" (60 mm x 762 mm) gpm (< Lpm) P " x 30" (60 mm x 762 mm) gpm (< Lpm) Filter Media Temperature Rating Polypropylene Fibers ºF ( ºC) WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. The P1, P5, P1-20, and P5-20 is Tested and Certified by NSF International to NSF/ANSI Standard 42 for material requirements only Pentair Filtration, Inc. Printed in USA MR

103 PCC SERIES CARTRIDGES PCC212 PCC218 PCC SERIES HEXAMETAPHOSPHATE CRYSTAL CARTRIDGES PCC Series filter cartridges contain food-grade hexametaphosphate that dissolve slowly in water to inhibit scale and rust build-up. These cartridges are available in four feeder sizes with variable volumes of phosphate crystals. All materials are FDA grade. They are effective for treating scale, corrosion and iron problems for up to six months at various flow rates and feed concentrations. The PCC212 and PCC218 cartridges are designed to fit PENTEK #10 Standard or Slim Line filter housings. The PCC-1 cartridge is designed to fit in #10 Standard filters only. The PCC-106 is an insert element that is placed in the center core of the cartridge. It is designed for use with standard 10" and 20" radial flow, sediment and carbon block double open-ended filter cartridges. This type of treatment is recommended for use with ice machines, coffee and vending machines, food service equipment, water heaters, air conditioning equipment and many other types of water processing equipment. PCC-1 PCC-106

104 PCC SERIES SCALE: Hardness particles are kept separated so they cannot precipitate and form deposits when heated. Maximum hardness 15 gpg. CORROSION: A protective coating is formed on all metal surfaces, safeguarding against acidity/alkalinity, hardness, chloride and other factors which effect the corrosion of water equipment and pipes. ph range IRON: Dissolved iron, up to 1 ppm, is kept suspended in solution (sequestered), preventing dissolved iron from precipitating, which would cause staining and discoloration. PCC " x 9 5 8" (73 mm x 244 mm) Up to 5 gpm (19 Lpm) PCC " x " (27 mm x 138 mm) 1 to 1.5 gpm (4 to 6 Lpm) for insertion in center core of open core cartridges PCC " x 9 3 4" (67 mm x 248 mm) 1 to 1.5 gpm (4 to 6 Lpm) PCC " x 9 3 4" (67 mm x 248 mm) 1.5 to 2.5 gpm (6 to 10 Lpm) Filter Media Food Grade Polyphosphate Shell Polypropylene Post-Filter Polypropylene Gaskets Buna-N (PCC212 & PCC218) Temperature Rating ºF ( ºC) CAUTION: Eye irritant. Contains sodium calcium hexametaphosphate. Avoid contact with eyes. In case of eye contact, flush with water for 15 minutes, get medical attention. Keep out of reach of children. WARNING: For drinking water applications, do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. NOTE: PCC212 and PCC218 cartridges are not recommended for main line water applications with flow rates exceeding 3.0 gpm (11.4 lpm). NOTE: With steamers, the water should be flushed daily. CAUTION: Do not use this cartridge on water that will be carbonated Pentair Filtration, Inc. Printed in USA MR

105 PCF SERIES CARTRIDGES BBF1-20MB PCF SERIES MIXED BED DEIONIZATION CARTRIDGES PCF1-10MB PCF1-20MB PCF Series filter cartridges have been developed in response to the requirements for deionized water in many industries. They are manufactured using an FDA-compliant resin that has been subjected to additional postproduction steps to minimize the total organic carbon (TOC) level. These high-capacity, semi-conductorgrade resin cartridges are ideal for use in pharmaceutical and medical laboratories, cosmetics, and circuit board printing applications. PCF Series cartridges are available in three sizes, flow rates and capacities. They are convenient and cost effective for many applications where low levels of total organic carbon (TOC) and total dissolved solids (TDS) are required. Applications:

106 PCF SERIES FUNCTION STRUCTURE: PHYSICAL FORM: IONIC FORM: PERCENT CONVERSION: 3 ) 2 2 3" x 9 3 4" (68 mm x 248 mm) 270 (17,500) 2 2 3" x 20" (68 mm x 508 mm) 600 (38,800) 4 1 2" x 20" (114 mm x 508 mm) 1850 (120,000) Filter Media End Caps Shell Pre-Filter Post-Filter Gaskets Temperature Rating Polypropylene Polypropylene Polypropylene Polypropylene ºF ( ºC) gpm gpm gpm WARNING: NOTE: CAUTION: Do not use cartridges on equipment that has an electric conductivity water level indicator.

107 POLYDEPTH SERIES CARTRIDGES POLYDEPTH SERIES POLYPROPYLENE CARTRIDGE The POLYDEPTH filtration cartridge is constructed of thermally bonded polypropylene microfibers to ensure high efficiency. The filter incorporates a rigid polypropylene center core for increased collapse strength and durability. This thermal bonded micro-fiber construction has minimal fiber release, consistent flow rate and superior filtration performance. It also is not brittle or prone to breakage problems like resin-bonded cartridges. Unique micro-grooves provide added surface area. The polydepth cartridge will not impart taste, odor or color to the liquid being filtered, which makes it ideal for food and beverage applications. The recommended temperature limit of 40ºF to 175ºF (4.4ºC to 79.4ºC) allows it to be used in many hot water applications. Additionally, the polypropylene construction provides superior chemical resistance and is not prone to bacterial attack. Available in different lengths from 9 3 4" up to 40". Unlike competitive cartridges, the longer lengths are not manufactured by gluing shorter cartridges together. They are continuous cartridges that cannot separate during use and do not sacrifice filtering surface area. POLYDEPTH cartridges are available in various micron ratings including 1-, 5-, 10-, 25-, and 50- microns.

108 POLYDEPTH SERIES Filter Media Temperature Rating Polypropylene ºF ( ºC) WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. PD " x 9 7 8" (64 mm x 251 mm) 1 <2 2 gpm (< Lpm) PD " x 9 7 8" (64 mm x 251 mm) 5 <2 2 gpm (< Lpm) PD " x 9 7 8" (64 mm x 251 mm) 10 <2 2 gpm (< Lpm) PD " x 9 7 8" (64 mm x 251 mm) 25 <2 2 gpm (< Lpm) PD " x 9 7 8" (64 mm x 251 mm) 50 <2 2 gpm (< Lpm) PD " x 20" (64 mm x 510 mm) 1 <2 5 gpm (< Lpm) PD " x 20" (64 mm x 510 mm) 5 <2 5 gpm (< Lpm) PD " x 20" (64 mm x 510 mm) 10 <2 5 gpm (< Lpm) PD " x 20" (64 mm x 510 mm) 25 <2 5 gpm (< Lpm) PD " x 20" (64 mm x 510 mm) 50 <2 5 gpm (< Lpm) PD " x 30" (64 mm x 763 mm) 1 <2 7 gpm (< Lpm) PD " x 30" (64 mm x 763 mm) 5 <2 7 gpm (< Lpm) PD " x 30" (64 mm x 763 mm) 25 <2 7 gpm (< Lpm) PD " x 40" (64 mm x 1017 mm) 1 <2 9 gpm (< Lpm) PD " x 40" (64 mm x 1017 mm) 5 <2 9 gpm (< Lpm) PD " x 40" (64 mm x 1017 mm) 25 <2 9 gpm (< Lpm) The PD-1-934, PD-5-934, PD , PD25-934, PD , PD-1-20, PD-5-20, PD-10-20, PD25-20 and PD are Tested and Certified by NSF International to NSF/ANSI Standard 42 for material requirements only.

109 R SERIES CARTRIDGES R SERIES PLEATED POLYESTER CARTRIDGES R30-20 R50 R30-20BB R50BB R R Series cartridges are manufactured from a durable, non-woven and reusable polyester fabric that is suitable for a wide range of filtration uses. The media is pleated around a polypropylene core for added strength and the ends are immersed in a thermo-setting vinyl plastisol. Embedding and sealing each end of the pleat in this fashion fuses the three components together forming a unified end cap and gasket. The overlap seam is sonically welded to reduce internal bypass improving filtration efficiency. The standard length cartridge has more than four square feet of polyester fabric, while the larger Big Blue version has more than 16 square feet. The media is pleated to maximize dirt-holding capacity and extend the time period between changes or cleaning. R Series cartridges are resistant to both bacteria and chemical attack making them suitable for a variety of residential, commercial and industrial applications.

110 R SERIES Sediment Reduction Percent Efficiency R50-BB R30-BB R30 R50 R Approximate Net Pressure Drop psi (Bar) 1.0 (0.069) 0.8 (0.062) 0.6 (0.041) 0.4 (0.028) 0.2 (0.014) R R30 R30-BB R50 R50-BB Particle Size (Microns) 0 1 (3.8) 2 (7.6) 3 (11.4) 5 (18.9) 6 (22.7) Flow Rate gpm (Lpm) 8 (30.3) 10 (37.9) 2 5 " x 4 30 R " x R " x R R30-BB 4 1 2" x R50-BB 4 1 2" x R30-20BB Filter Media Endcaps Core Temperature Rating WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

111 S1 SERIES CARTRIDGES S1 SERIES PLEATED CELLULOSE CARTRIDGES S1 Series cartridges are manufactured from a pleated cellulose media and are designed for general water filtration purposes. The media is pleated around a polypropylene core for added strength and the ends are immersed in a thermo-setting vinyl plastisol. Embedding and sealing each end of the pleat in this fashion fuses the three components together forming a unified end cap and gasket. The overlap seam is sonically welded to reduce bypass, improving filtration efficiency. S1 Series cartridges are economically priced and highly effective at reducing sediment particles down to 20 microns in size.

112 S1 SERIES 100 Sediment Reduction Percent Efficiency S1-BB CARTRIDGES S1 STANDARD CARTRIDGES Particle Size (Microns) S " x 9 3 4" (67 mm x 248 mm) gpm ( Lpm) 580 in. 2 (0.38 m 2 ) 12 gpm (45 Lpm) S " x 20" (67 mm x 508 mm) gpm ( Lpm) 1110 in. 2 (0.72 m 2 ) 15 gpm (57 Lpm) S1-BB 4 1 2" x 9 3 4" (114 mm x 248 mm) gpm ( Lpm) 2070 in. 2 (1.34 m 2 ) 20 gpm (76 Lpm) S1-20BB 4 1 2" x 20" (114 mm x 508 mm) gpm ( Lpm) 4280 in. 2 (2.77 m 2 ) 35 gpm (132 Lpm) Filter Media Resin-Impregnated Cellulose End Caps Vinyl Plastisol Core Polypropylene Temperature Rating ºF ( ºC) NOTE: S1-BB and S1-20BB are for use in 10" and 20" Big Blue housings and BBFS systems only. NOTE: Big Blue (BB) is a registered trademark of Pentair Filtration, Inc. WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system Pentair Filtration, Inc. Printed in USA JE

113 RFFE20-BB CARTRIDGE RFFE20-BB RADIAL FLOW IRON REDUCTION CARTRIDGE The RFFE20-BB filter cartridge is designed to provide an easy and effective method of reducing iron from water, which greatly improves the taste. This cartridge helps to eliminate the orange and brown stains often found in sinks, toilets, tubs and other plumbing fixtures. It also reduces the possibility of damage to pipes and water heaters and reduces up to 3 ppm dissolved iron. It adds no harmful chemicals to the water, making it completely safe for drinking water applications. The RFFE20-BB cartridge is designed for use in the PENTEK 20-inch BB filter housings and should be installed on the main cold water line after the pressure tank or water meter. For best results, presediment and post-carbon treatment is recommended. RFFE20-BB

114 RFFE20-BB 6 Approximate Net Pressure Drop psi (Bar) RFFE20-BB Flow Rate gpm (Lpm) 3 ppm 26,000 gal 104 days 208 days 416 days 2 ppm 40,000 gal 160 days 320 days 640 days 1 ppm 80,000 gal 320 days 640 days 1280 days 0.5 ppm 160,000 gal 640 days 1280 days N/A ph >7.0 Silica Manganese Iron Iron Bacteria Hydrogen Sulfide <100 ppm <1 ppm <3 ppm None None NOTE: Water conditions outside of the above specified limits may lead to a shortened filtration life. If your water contains Iron Bacteria, shock chlorination is recommended. WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the unit. CAUTION: Protect against freezing to prevent cracking of the filter and water leakage. NOTE: The RFFE20-BB and RFC20-BB cartridges will contain a very small amount of fines (very fine powder) and new cartridges, after installation, should be flushed with sufficient water to remove all traces of fines from your water system before use.

115 WS SERIES CARTRIDGES WS-20BB WS SERIES WATER SOFTENER CARTRIDGES 3 WS Series cartridges are designed to allow optimal contact between water and resin surfaces, ensuring maximum ion exchange. The internal expansion pad minimizes channeling, while the post filter eliminates any potential for bypass. Designed for low water usage, these units will easily deliver softened product water through the use of FDA-grade sodium based, nonsolvent rinsed softening resin. The cartridge style design provides a convenient solution for delivering softened water to protect sensitive water delivery equipment. WS Series cartridges are available in three sizes for use in PENTEK s SlimLine, Standard, and Big Blue Series filter housings. Properly sized, these units can effectively treat water in applications desiring low hardness and scale deposits with capacity ranging between 750 to 4,500 grains. PENTEK s water softening cartridges provide superior performance and outstanding protection for medical equipment, coffee and espresso appliances, low volume beverage and commercial food service machines. WS-10 WS-20

116 WS SERIES 3 ) WS " x 9 3 4" (67 mm x 248 mm) 0.50 gpm (1.9 Lpm) 750 WS " x 20" (67 mm x 508 mm) 0.75 gpm (2.8 Lpm) 1500 WS-20BB 4 1 2" x 20" (114 mm x 508 mm) 2.0 gpm (8.5 Lpm) 4500 Filter Media End Caps Pre-Filter Post-Filter Gaskets Temperature Rating Cation, sodium-form resin, 20 x 40 mesh, R-SO3-Na+ Polypropylene Polypropylene Polypropylene Buna-N 100ºF (37.8ºC) WARNING: For drinking water applications, do not use where the water is microbiologically unsafe or with water of unknown quality without adequate disinfection before or after the system Pentair Filtration, Inc. Printed in USA MR

117 SPECIFICATIONS AND PERFORMANCE Membrane: Polyethersulfone Membrane Assembly: Polystyrene, epoxy resin Carbon Pre-Filter: technology contains activated carbon with synthetic Polymeric fibers and binders O-ring Seals: EPDM End Caps: Top: Polystyrene, Bottom: Polypropylene Netting: Bottom: Polyolefin (MG-10MCB only) Water Temperature Range: Pressure Differential: 88 psi (6.1 bar), max. Storage Temperature Range: C) ph Range: 2-12 Operating Pressure Range: 5-88 psi ( bar), max. Water Turbidity: < 1 NTU Bacteria Reduction: Organism: Brevundimonas diminuta (0.2 micron in size). Method: Cyst Reduction: Method: latex microspheres. MG-10MCB MG-10T 1 gpm 3 gpm MG-10MCB MG-10T 13 3 gpm ( lpm) MG-10MCB MG-10T ** Capacities may vary depending on local water quality, type of pre-filtration and acceptable minimum flow rate. WARNING: Do not use on water that may be contaminated by untreated surface water, water that may be contaminated by human or animal sewage or other wastewater. These cartridges are not intended for reducing pathogenic (disease-causing) virus particles, if present in the water, to below safe levels. Note: These cartridges are intended for use on visually clear drinking water that meets all other public health standards. Note: Product features are subject to change by Pentair Water at any time without notice. Not certified for sale in California, Iowa, Massachusetts and Wisconsin.

118 MICROGUARD SERIES 100 (6.9) (5.2) 50 (3.4) MG-10MCB MG-10T Membrane Triple Element (membrane only) ( mm) ( mm) (73 mm) 3.0 (76 mm) HEP High Efficiency Pleated Cartridge EP-10 Carbon Block Cartridge CBC-10 Carbon Block Cartridge PD Polydepth Cartridge Not certified for sale in California, Iowa, Massachusetts and Wisconsin absolute rating 0.15 absolute rating PENTEK Standard and Slimline 3G Housing PENTEK Standard and Slimline 3G Housing Printed in USA JA

119 BP, BPHE, & BN SERIES BAGS BP-420 BN-420 BP, BPHE AND BN SERIES FILTER BAGS BP-410 BN-410 BHPE-420 BHPE-410 Polypropylene bags are compatible with a broad range of corrosive fluids including organic solvents, oils, acids, alkalis and microorganisms. BP Series (Polypropylene Felt) Bags An assortment of filtration ratings is offered from 1 to 200 microns to comply with any filtration requirement. The bags are manufactured from felt due to its high solids loading capabilities, in comparison to similar mesh fabrics. The media is created by needle-punching two layers of synthetic fibers together in a supporting scrim. A glazed finish, created by melting the outermost surface fibers, is used to produce a bond that reduces the possibility of migration. BPHE Series (High Efficiency) Bags High efficiency bags are offered for those critical applications when high efficiency combined with high dirt-holding capacity is required. Polypropylene materials are processed into microfibers with diameters of 1-10 microns or more. These fibers are converted into filter material. Microfiber media are covered with spun-bonded polypropylene. BN Series (Strainer) Bags Woven monofilment materials are offered in nylon with micron ratings of and efficiencies from 75 to 95 percent. The materials are cleanable and reusable.

120 BP, BPHE, & BN SERIES Viscosity (cps) Correction Factor BP-410 4" x 8 5 8" (102 mm x 218 mm) Glazed Polypropylene Felt 1, 5, 10, 25, 50, 100, BP-420 4" x 18" (102 mm x 457 mm) Glazed Polypropylene Felt 1, 5, 10, 25, 50, 100, BPHE-410 BPHE-420 4" x 8 5 8" (102 mm x 218 mm) 4" x 18" (102 mm x 457 mm) Polypropylene microfibers with spun-bonded polypropylene covers Polypropylene microfibers with spun-bonded polypropylene covers 1, 5, 10, 25, 50, 75, , 5, 10, 25, 50, 75, BN-410 4" x 8 5 8" (102 mm x 218 mm) Nylon monofilament mesh 50, 100, 150, 200, 250, 300, 400, 600, BN-420 4" x 18" (102 mm x 457 mm) Nylon monofilament mesh 50, 100, 150, 200, 250, 300, 400, 600, Maximum Temperature 200ºF (93.3ºC) See application literature for housing rating. WARNING: For drinking water applications, do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. NOTE: This information is for general guidance. Users should test bag materials with media involved to determine compatibility. CAUTION: Protect against freezing to prevent cracking of the filter and water leakage Pentair Filtration, Inc. Printed in USA MR