PUF (PolyUrethane Foam) Sampler. GPS-1 Volumetric Flow Controlled Part Number Jul2008

Transcription

1 PUF (PolyUrethane Foam) Sampler GPS-1 Volumetric Flow Controlled Part Number Jul2008

2 2007 Thermo Fisher Scientific Inc. All rights reserved. Specifications, terms and pricing are subject to change. Not all products are available in all countries. Please consult your local sales representative for details. Thermo Fisher Scientific Air Quality Instruments 27 Forge Parkway Franklin, MA

3 WEEE Compliance This product is required to comply with the European Union s Waste Electrical & Electronic Equipment (WEEE) Directive 2002/96/EC. It is marked with the following symbol: Thermo Fisher Scientific has contracted with one or more recycling/disposal companies in each EU Member State, and this product should be disposed of or recycled through them. Further information on Thermo Fisher Scientific s compliance with these Directives, the recyclers in your country, and information on Thermo Fisher Scientific products which may assist the detection of substances subject to the RoHS Directive are available at: Thermo Fisher Scientific WEEE Compliance

4 Warranty Seller warrants that the Products will operate or perform substantially in conformance with Seller's published specifications and be free from defects in material and workmanship, when subjected to normal, proper and intended usage by properly trained personnel, for the period of time set forth in the product documentation, published specifications or package inserts. If a period of time is not specified in Seller s product documentation, published specifications or package inserts, the warranty period shall be one (1) year from the date of shipment to Buyer for equipment and ninety (90) days for all other products (the "Warranty Period"). Seller agrees during the Warranty Period, to repair or replace, at Seller's option, defective Products so as to cause the same to operate in substantial conformance with said published specifications; provided that (a) Buyer shall promptly notify Seller in writing upon the discovery of any defect, which notice shall include the product model and serial number (if applicable) and details of the warranty claim; (b) after Seller s review, Seller will provide Buyer with service data and/or a Return Material Authorization ( RMA ), which may include biohazard decontamination procedures and other product-specific handling instructions; and (c) then, if applicable, Buyer may return the defective Products to Seller with all costs prepaid by Buyer. Replacement parts may be new or refurbished, at the election of Seller. All replaced parts shall become the property of Seller. Shipment to Buyer of repaired or replacement Products shall be made in accordance with the Delivery provisions of the Seller s Terms and Conditions of Sale. Consumables, including but not limited to lamps, fuses, batteries, bulbs and other such expendable items, are expressly excluded from the warranty under this warranty. Notwithstanding the foregoing, Products supplied by Seller that are obtained by Seller from an original manufacturer or third party supplier are not warranted by Seller, but Seller agrees to assign to Buyer any warranty rights in such Product that Seller may have from the original manufacturer or third party supplier, to the extent such assignment is allowed by such original manufacturer or third party supplier. In no event shall Seller have any obligation to make repairs, replacements or corrections required, in whole or in part, as the result of (i) normal wear and tear, (ii) accident, disaster or event of force majeure, (iii) misuse, fault or negligence of or by Buyer, (iv) use of the Products in a manner for which they were not designed, (v) causes external to the Products such as, but not limited to, power failure or electrical power surges, (vi) improper storage and handling of the Products or (vii) use of the Products in combination with equipment or software not supplied by Seller. If Seller determines that Products for which Buyer has requested warranty services are not Thermo Fisher Scientific Warranty

5 covered by the warranty hereunder, Buyer shall pay or reimburse Seller for all costs of investigating and responding to such request at Seller's then prevailing time and materials rates. If Seller provides repair services or replacement parts that are not covered by the warranty provided in this warranty, Buyer shall pay Seller therefor at Seller's then prevailing time and materials rates. ANY INSTALLATION, MAINTENANCE, REPAIR, SERVICE, RELOCATION OR ALTERATION TO OR OF, OR OTHER TAMPERING WITH, THE PRODUCTS PERFORMED BY ANY PERSON OR ENTITY OTHER THAN SELLER WITHOUT SELLER'S PRIOR WRITTEN APPROVAL, OR ANY USE OF REPLACEMENT PARTS NOT SUPPLIED BY SELLER, SHALL IMMEDIATELY VOID AND CANCEL ALL WARRANTIES WITH RESPECT TO THE AFFECTED PRODUCTS. THE OBLIGATIONS CREATED BY THIS WARRANTY STATEMENT TO REPAIR OR REPLACE A DEFECTIVE PRODUCT SHALL BE THE SOLE REMEDY OF BUYER IN THE EVENT OF A DEFECTIVE PRODUCT. EXCEPT AS EXPRESSLY PROVIDED IN THIS WARRANTY STATEMENT, SELLER DISCLAIMS ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, ORAL OR WRITTEN, WITH RESPECT TO THE PRODUCTS, INCLUDING WITHOUT LIMITATION ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. SELLER DOES NOT WARRANT THAT THE PRODUCTS ARE ERROR-FREE OR WILL ACCOMPLISH ANY PARTICULAR RESULT. Warranty Thermo Fisher Scientific

6 OPERATING INSTRUCTIONS MODEL PS-1 A. UNIT PREPARATION. Contents of two boxes: Shelter box: 46 x 20 x 23 GPS1-1 Dual sampling module GPS1-6 Flow selector / elapsed time indicator GPS1-7 Seven day mechanical timer GPS1-8 Magnehelic gauge GPS1-9 Flow venturi GPS1-11 Blower motor assembly GPS1-15 Exhaust hose GPS1-19 Anodized aluminum shelter Lid box: 20 x 15 x 15 G10291 Shelter lid Assembly instructions: 1. Remove the PS-1 PUF Sampler from the shipping carton. 2. Locate the shelter lid and install on the aluminum shelter as follows: a. Align the hinges of the lid to the rear of the shelter and fasten with four (4) x 1/2" pan head screws. b. Secure the front catch, (see figure A) to the shelter front using two (2) x 1/2" flat head screws. c. Secure the rear catch to the shelter back panel using one (1) x 1/2" pan head screw. d. Secure the rear lid clasp to the shelter lid using two (2) x 1/2" pan head screws. Note: These three catches may need readjustment to operate the shelter lid properly. e. Adjust the front and rear catches to be sure that the lid slot lowers over the front catch when closing the lid and aligns with the rear catch when the lid is in the open position. f. The lid can now be secured in an open or closed position with the aluminum strip or a padlock. 3. Find one (1) sampling module in the packing container and install on the inlet port. The inlet port has a 1/2" threaded male fitting. Place the module over the male fitting and screw it on until snug. 4. Pull the exhaust hose from out of the shelter bottom and extend it away from the shelter on the ground. 5. Open the shelter door and timer. 6. Prepare the timer for the desired start and stop times. Thermo Fisher Scientific

7 B. Unit Calibration. 1. Calibration of the PUF Sampler is performed without a foam slug or filter paper in the sampling module. However, the empty glass cartridge must remain in the module to insure a good seal through the module. 2. Install the G40 Calibrator on top of the 4" filter holder. 3. Connect an 8" water manometer to the Calibrator. 4. Open the ball valve fully. 5. Turn the system on by tripping the manual switch on the timer. Allow a few minutes for warm-up. 6. Adjust the voltage control screw to obtain a reading of 70 inches on the dial gage, (Magnehelic Gage). 7. With 70 inches on the dial gage as your first calibration point, record it and the manometer reading on the data sheet. 8. Close the ball valve slightly to readjust the dial gage down to 60 inches. Record the figure and manometer reading on the data sheet. 9. Using the above procedure, adjust the ball valve for readings at 50, 40, and 30 inches and record on the data sheet. 10. Using these two sets of readings, plot a curve on the data sheet. This curve will be used for determining the actual flow rate in the field. 11. Re-adjust the voltage control fully clockwise to maximum setting. Open ball valve fully. C. Unit Operation. 1. The PUF Sampler may be operated at ground level or on rooftops. In urban or congested areas, it is recommended that the sampler be placed on the roof of a single story building. The sampler should be located in an unobstructed area, at least two meters from any obstacle to airflow. The exhaust hose should be stretched out in a down wind direction if possible. 2. The sampler should be operated for 24 hours in order to obtain average daily levels of airborne pesticides. 3. on and off times and weather conditions during sampling periods should be recorded. Air concentrations may fluctuate with time of day, temperature, humidity, wind direction and velocity and other climatological conditions. Thermo Fisher Scientific

8 4. Air flow-readings should be taken (dial gage) at the beginning and end of each sampling period. Differences between the beginning and ending flow rates should be averaged out to obtain an overall flow rate. (The PUF Sampler can be fitted with a gas meter which would give a direct reading of the total flow.) 5. Blower motor brushes should be inspected frequently and replaced before expending. 6. An electrical source of 110 volts, 15 amps is required. D. Descriptions of Sampling Media (Sorbents) 1. Two types of sampling media are recommended for use with the PUF Sampler: polyurethane foams and granular solid sorbents. Foams may be used separately or in combination with granular solids. The sorbent may be extracted and reused (after drying) without unloading the cartridge. 2. Polyurethane Foam (PUF): a. Use polyether-type polyurethane foam (density No. 3014, grams/cm3, or equivalent). This is the type of foam generally used for furniture upholstery, pillows, and mattresses.(general Metal Works' part number PS1-16 is recommended. It is a 3" PUF plug. Also available are two and one inch pieces.) This type of foam is white and yellows on exposure to light. 3. Granular Solids: a. Porous (macroreticular) chromatography sorbents recommended. Pore sizes and mesh sizes must be selected to permit air flow rates of at least 200 liters/minute. Approximately 25 cm3 of sorbent is recommended. The granular solids may be sandwiched between two layers of foam to prevent loss during sampling and extraction. E. Sampling Module. 1. Release the three (3) swing bolts on the 4" filter holder (FH-2104) and remove the hold down ring. 2. Install a clean 102mm dia. quartz/glass fiber filter on the support screen and secure it with the hold down ring and swing bolts. 3. Unscrew together the 4" filter holder and the sampling module cap leaving the module tube in place with the glass cartridge exposed. 4. Load the glass cartridge with foam and or foam/granular solids and replace in the module tube. Fasten the glass cartridge with the module cap and 4" filter holder Thermo Fisher Scientific

9 assembly while making sure that the module assembly, 4" filter holder and all fittings are snug and not over tighten. 5. The glass cartridge and glass fiber filter should be removed from the sampler with forceps and clean, gloved hands and immediately placed in' a. sealed container for transport to the laboratory. Similar care should be taken to prevent contamination of the filter paper and vapor trap (foam) when loading the sampler. 6. It is recommended to have two (2) sampling modules for each sampling system so that filter and foam exchange can take place in the laboratory. DUAL SORBENT VAPOR TRAP Thermo Fisher Scientific

10 MODEL PS-1 PUF SAMPLER Replacement parts PSl-l Dual sampling module with FH " filter holder, less glass cartridge PS " round Filter Holder (FH-2104) PSI silicone gasket (top module) PS Glass Cartrigde wl support screens PS Silicone gasket (bottom module) PSI Voltage Variator/Elatped Timer PS Seven Day Skip Timer (GMW-70) PS Magnehelic Gage PS Flow Venturi PS Flow Valve PS Blower Motor-Assembly PS Motor Cushion PS Replacement Motor only PS Replacement Motor Brushes (B-1) PS Exhaust Hose PSI PUF (polyurethane foam) plug 3" PS PUF (polyurethane foam) plug 2" PS PUF (polyurethane foam) plug 1" PS Aluminum Outdoor Shelter Complete PS Male Adapter for bottom of module PS Aluminum Quick Disconnect Coupler G Calibration Kit with NBS Curve Thermo Fisher Scientific

11 Thermo Fisher Scientific

12 MOTOR BRUSH SEATING PROCEDURE On re-assembly and handling, the lead wires must be kept away from rotating parts and motor frame. To achieve best performance, the new brushes should be seated on the commutator before full voltage is applied. After brush change apply approximately 50% voltage for thirty minutes to accomplish this seating. The motor will return to full performance after thirty to forty-five minutes running at full voltage. Caution Direct application of full voltage after changing brush will cause arcing, commutator pitting, and reduce overall life. Use of the Model GMW Voltage Variator provides the reduced voltage needed for brush seating. If reduced voltage is unavailable, connect two motors of similar rating in series for thirty minutes to accomplish the brush seating. WARNING THE BRUSHES SHOULD BE CHANGED BEFORE THE BRUSH SHUNT TOUCHES THE COMMUTATOR. SPECIAL NOTE: When ordering GMW Replacement Motor Brushes, compare brush configuration carefully! GB-1 Brush Sets used on motors furnished after January 1978 GB-3 Brush Sets used on motors furnished prior to January 1978 only. Motor Brush "U" clip connectors used with GB-3 brush sets only. Thermo Fisher Scientific

13 Thermo Fisher Scientific

14 SERVICE LOCATIONS For additional assistance, Environmental Instruments Division has service available from exclusive distributors worldwide. Contact one of the phone numbers below for product support and technical information Toll Free International Thermo Fisher Scientific