STRONG PARTNERS. TOUGH TRUCKS. Powered Stacker with Folding Platform S1.5S, S1.5Sil, S1.5Ssl

Transcription

1 STRONG PARTNERS. TOUGH TRUCKS. Powered Stacker with Folding Platform S1.5S, S1.5Sil, S1.5Ssl

2 S1.5S, S1.5Sil, S1.5Ssl Specification Data is based on VDI 2198 Equipment and weight: Weights (line) are based on the following specifications: Complete truck with 180 mm wide forks (S1.5S) or 193 mm wide forks (S1.5 IL) or 100 mm forks (Straddle leg SL), polyurethane drive/steer tyre, and 2-Stage mm mast Forks: S1.5S: 65 x 180 x mm long S1.5S IL: 65 x 193 x mm long S1.5S SL: 35 x 100 x mm long

3 Mast and capacity information Values shown are for standard equipment. When using non-standard equipment, these values may change. Please contact your Hyster dealer for information. The rated capacities shown are for masts in a vertical position on trucks equipped with standard or sideshift carriage, and nominal length forks. Masts above the maximum fork heights shown in the mast table are classified as high lift, and depending on the tyre/tread configuration may require reduced capacity, restricted back tilt or wide tread. Forks spacing: Inside to inside: 210mm (S1.5S) 184mm (S1.5S IL) Outside to outside: 570 mm (1.5S) 570 mm (S1.5S IL) 800 mm, mm, mm adjustable (S1.5S SL)

4 NOTE: Specifications are affected by the condition of the vehicle and how it is equipped, as well as the nature and condition of the operating area. If these specifications are critical, the proposed application should be discussed with your dealer. Traction, lift, and lower speeds may vary with alternative lift height Values determined by wheel friction, if climbing ramps frequently (within 1h), consult your salesman () Value or text in brackets are referred to truck fitted out with side fix protection (biga) or rear fix protection (bob) Values are referred to a 2-stg mast HiVi, h 3 =2 968 mm If truck fitted out with three stage FFL mast,h 3 =4 628 mm add 172 kg Values referred to truck equipped with 2-stg mast, and battery at row 6.4, add 50 Kg when fitted out with side fix protection (biga) or rear fix protection (bob) + 61 with fixed lateral protections (Biga), with Rear protections (Bob) + 75 with fixed lateral protections (Biga), with Rear protections (Bob) Values + 18 mm with 3-stg mast Values + 12 mm with 3-stg mast Values - 18 mm with 3-stg mast Mast tables: h 1 with 100 mm free lift h 4 with load backrest add 528 mm When initial lift is lifted add 130 mm Notice Care must be exercised when handling elevated loads. When the carriage and/or load is elevated, truck stability is reduced. It is important that mast tilt in either direction be kept to a minimum when loads are elevated. Operators must be trained and adhere to the instructions contained in the Operating Manual. Hyster products are subject to change without notice. Lift trucks illustrated may feature optional equipment. Safety: This truck conforms to the current EU requirements.

5 Product Features S1.5S S1.5Sil S1.5Ssl Powered stacker with folding platform Powered stacker with folding platform, initial lift Powered stacker with folding platform, straddle legs Also available with tandem load wheels Dependability MOSFET high frequency Combi controller for traction and hydraulic controls. Welded fork construction makes them highly resistant to torsion and heavy loads. Hour meter and battery discharge indicator with lift interrupt fitted as standard. Cold store protection for application to -30 C. Specific 'initial lift' and 'straddle legs' models provide the right answer to any application. High visibility and full free lift 2 and 3-stage masts availability. Productivity Operator-friendly tiller head controls for productive load handling. Regenerative braking and anti-rollback both available as standard. Pedestrian or stand-on operation, with or without side arms raised for improved poductivity. Progressive speed control and steering system ensure optimum performance levels. Tandem load wheels and exit/entry rollers as standard. Key-pad with PIN code for enhanced fleet management. Power steering makes truck highly manoeuvrable. Ergonomics Ergonomically designed tiller head for maximum operator comfort. Low effort controls ergonomically positioned to reduce operator fatigue. Dual lift/lower controls allow operation using either hand. 'Corner control' system reduces speed automatically when cornering. 5-point wheel layout, with fixed stabilizer wheels, provides enhanced stability. Adjustable performance settings to suit specific operating conditions. Cost of ownership AC drive motor provides superior performance and reduced operation costs. Power transmission supplied via helicoidal gears, running in oil bath. IP54 standards control for protection against dust and water. Optimum component reliability permit the extension of service materials. Serviceability AC drive motor and brushless lift motor construction ensures low maintenance requirements. Built-in diagnostic system for preventative maintenance communication reduces downtime. Driver Diagnostic Interface (DDI) allows selection of appropriate performance settings for specific applications. CANbus technology for increased functionality, reliability and servicing.

6 TM Strong Partners, Tough Trucks, for Demanding Operations Everywhere. Hyster supplies a complete product range, including Warehouse trucks, IC and Electric Counterbalanced trucks, Container Handlers and Reach Stackers. Hyster is committed to being much more than a lift truck supplier. Our aim is to offer a complete partnership capable of responding to the full spectrum of materials handling issues: Whether you need professional consultancy on your fleet management, fully qualified service support, or reliable parts supply, you can depend on Hyster. Our network of highly trained dealers provides expert, responsive local support. They can offer cost-effective finance packages and introduce effectively managed maintenance programmes to ensure that you get the best possible value. Our business is dealing with your materials handling needs so you can focus on the success of your business today and in the future. Hyster Europe, Flagship House, Reading Road North, Fleet, Hants GU51 4WD, England. Tel: +44 (0) Fax: +44 (0) info@hyster.co.uk A division of NACCO Materials Handling Limited. 02/08/TLC Printed in England Form No /0 Hyster,, Vista and Monotrol are registered trademarks of Hyster Company in the United States and in certain other countries. TM, Fortens TM, Pacesetter VSM TM, DuraMatch TM, DuraMatch Plus TM, TouchPoint TM, TouchControl TM, EZXchange & HSM TM are trademarks of Hyster Company in the United States and in certain other countries.