MATERIALIZING VISIONS. Bohler-Uddeholm Holder
|
|
- Jocelin Burns
- 6 years ago
- Views:
Transcription
1 MATERIALIZING VISIONS Bohler-Uddeholm Holder
2 General Nitriding temperature Nitriding time Depth of case appr. Bohler-Uddeholm HOLDER is a free-machining chromiummolybdenum alloyed steel which is supplied in the prehardened condition. Holder is characterized by: Excellent machinability Good resistance to indentation Uniform hardness in all dimensions F C hours in mm Delivery condition Color code Hardened and tempered to approximately Brinell Yellow/blue Nitrocarburizing Nitrocarburizing at 1060 F (570 C will give a surface hardness of approx. 700 HV. After 2 hours treatment, the hard layer will be approx in (0.01mm. This grade has been manufactured to our internal specifications, and audited to meet our guidelines. Applications Holders/bolsters for plastic molds and die-casting dies Plastics and rubber molds with low requirements on polishability Support plates Constructional parts Heat Treatment HOLDER is intended for use in the hardened and tempered condition, i.e., the delivery condition. Stress Tempering After rough machining, the tool should be heated through to 900 F, and held for a minimum of two hours once the entire tool is soaked through. Cool slowly to room temperature. Stress tempering temperatures in excess of 900 F may result in a permanent loss of strength, hardness, and/or dimensional tolerances. Properties PHYSICAL DATA Approx. values Samples taken from a round bar 1 (25 mm diameter. Hardness: 310 HB Temperature 68 F (20 C Tensile strength UTS (Rm psi N/mm 2 146,000 1,010 Yield strength YS (Rp 0.2 psi N/mm 2 116, F (200 C 138, , F (400 C 115, , Flame and induction hardening HOLDER can be flame or induction hardened to a hardness of approx. 50 RC. Cooling in air is preferable. Smaller pieces may however require forced cooling. Hardening should be immediately followed by tempering. Gasnitriding Nitriding gives a hard surface which is very resistant to wear and erosion. A nitrided surface also increases the corrosion resistance. The surface hardness after nitriding at a temperature of 975 F (525 C in ammonia gas will be approx. 650HV. 2
3 MILLING Face and square shoulder milling DRILLING High speed steel twist drill Rough milling Milling with carbide Fine milling Drill diameter Cutting speed (v c Feed (f inch mm i.p.r. mm/r Cutting speed (v c / * 60-65* /16-3/ * 60-65* Feed (f z inch/tooth mm/tooth Depth of cut (a p inch mm designation ISO P20-P40 Coated carbide P10-P20 Coated carbide or cermet 3/8-5/ * 60-65* /8-3/ * 60-65* * For coated HSS drills v c = ( drill Indexable Solide Type of drill Solide carbide Brazed carbide 1 End milling Cutting speed (v c Cutting speed (v c Solid carbide Type of milling indexable insert High speed steel Feed (f i.p.r. mm/r Drill with replaceable or brazed carbide tip 2 Feed rate for drill diameter 0,8-1.6 (20-40mm 3 Feed rate for drill diameter (5-20mm 4 Feed rate for drill diameter (10-20mm Feed (f z inch/tooth mm/tooth designation ISO - P20-P30-1 For coated HSS end mill v c 56 (17. 2 Depending on radial depth of cut and cutter diameter. 3
4 GRINDING General grinding wheel recommendations for Bohler- Uddeholm Holder is given below. Wheel selection Type of grinding Face grinding straight wheel Face grinding segments Cylindrical grinding Internal grinding Profile grinding Prehardend condition A 46 HV A 24 GV A 60 KV A 60 JV A 100 LV Welding Good results when welding tool steel can be achieved if proper precautions are taken during welding (elevated working temperature, joint preparation, choice of consumables and welding procedure. Welding method TIG MMA (SMAW Working temperature F ( C F ( C Welding consumables IMPAX TIG- WELD IMPAX WELD Hardness after welding HB HB 4
5 BOHLER-UDDEHOLM CORPORATION 2505 Millennium Drive, Elgin, IL The Steel Store This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty of specific properties of the products described or a warranty for fitness for a particular purpose. The latest revised edition of this brochure is the English version, which is always published on our web site Edition 1,
HOLDAX Prehardened holder steel
Prehardened holder steel This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationUddeholm Holdax. Classified according to EU Directive 1999/45/EC For further information see our Material Safety Data Sheets.
Uddeholm Holdax UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes without permission of the copyright holder. This information is based on our present state
More informationEdition 5, The latest revised edition of this brochure is the English version, which is always published on our web site
UDDEHOLM HOLDAX This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty of
More informationIMPAX SUPREME Prehardened mould steel
T OOL STEEL FACTS IMPAX Prehardened mould steel Wherever tools are made Wherever tools are used This information is based on our present state of knowledge and is intended to provide general notes on our
More informationIMPAX SUPREME. IMPAX Prehardened mould steel
IMPAX SUPREME IMPAX Prehardened mould steel 1 Edition: 4, 11.2003 No. 031101 This information is based on our present state of knowledge and is intended to provide general notes on our products and their
More informationRAMAX 2. Prehardened stainless holder steel
RAMAX 2 Prehardened stainless holder steel This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be
More informationMATERIALIZING VISIONS. Bohler-Uddeholm H13 TOOL STEEL
MATERIALIZING VISIONS Bohler-Uddeholm H13 TOOL STEEL Bohler-Uddeholm H13 General Bohler-Uddeholm H13 is a chromium-molybdenumvanadium alloyed steel which is characterized by: Good resistance to abrasion
More informationBy combining Uddeholm Ramax HH with one of our other products within the Stainless Concept, you can create a completely stainless mould.
UDDEHOLM RAMAX HH Uddeholm Ramax HH provides several benefits: The product offers uniform hardness in all dimensions combined with excellent indentation resistance. It is a corrosion resistant grade which
More informationHOTVAR. Hot work tool steel
Hot work tool steel General HOTVAR is a high performance molybdenumvanadium alloyed hot-work tool steel which is characterized by: High hot wear resistance Very good high temperature properties High resistance
More informationAISI A2 Cold work tool steel
T OOL STEEL FACTS AISI A2 Cold work tool steel Great Tooling Starts Here! General AISI A2 is an air- or oil hardening chromiummolybdenum-vanadium alloyed tool steel characterized by: Good machinability
More informationREGIN 3. Cold work tool steel
Cold work tool steel This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationPRELIMINARY BROCHURE CORRAX. A stainless precipitation hardening steel
PRELIMINARY BROCHURE CORRAX A stainless precipitation hardening steel This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses.
More informationCORRAX A stainless precipitation hardening steel
T OOL STEEL FACTS PRELIMINARY BROCHURE CORRAX A stainless precipitation hardening steel Wherever tools are made Wherever tools are used This information is based on our present state of knowledge and is
More informationHOTVAR Hot work tool steel
T OOL STEEL FACTS HOTVAR Hot work tool steel Wherever tools are made Wherever tools are used General HOTVAR is a high performance molybdenumvanadium alloyed hot-work tool steel which is characterized by:
More informationEdition 5, The latest revised edition of this brochure is the English version, which is always published on our web site
UDDEHOLM ALVAR 14 This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationUDDEHOLM RAMAX LH. Uddeholm Ramax LH is a part of the Uddeholm Stainless Concept.
UDDEHOLM RAMAX LH TAKING STANDARDS TO A NEW LEVEL Setting standards is important in the tooling industry. Uddeholm Ramax LH is no exception. It is a first class tool steel for mould bases, with excellent
More informationUDDEHOLM VIDAR 1 ESR
UDDEHOLM VIDAR 1 ESR This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationUDDEHOLM VIDAR 1 ESR
UDDEHOLM VIDAR 1 ESR This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationEdition 3, The latest revised edition of this brochure is the English version, which is always published on our web site
This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty of specific properties
More informationQRO 90 SUPREME. Hot work tool steel
QRO 90 SUPREME Hot work tool steel This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed
More informationQRO 90 SUPREME Hot work tool steel
T O O L S T E E L F A C T S QRO 90 Hot work tool steel Great Tooling Starts Here! Cover photo: Bo Dahlgren This information is based on our present state of knowledge and is intended to provide general
More informationSS-EN ISO 9001 SS-EN ISO 14001
UDDEHOLM FORMAXTM This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationUddeholm Formax. Formax is a trademark registered in Sweden
Uddeholm Formax Formax is a trademark registered in Sweden UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes without permission of the copyright holder.
More informationSUPERIOR MACHINABILITY
Uddeholm Balder Uddeholm Balder Reliable and efficient steel is essential for good results. The same goes for achieving high productivity and high availability. When choosing the right steel many parameters
More informationUddeholm Dievar is a specially developed steel grade by Uddeholm, which provides the best possible performance.
UDDEHOLM DIEVAR Uddeholm Dievar is a specially developed steel grade by Uddeholm, which provides the best possible performance. The chemical composition and the very latest in production technique make
More informationPRELIMINARY BROCHURE UDDEHOLM CORRAX
PRELIMINARY BROCHURE UDDEHOLM CORRAX Uddeholm Corrax stainless moulds steel has a unique set of properties that makes it the ultimate choice in a large number of demanding applications. Its superior resistance
More informationUDDEHOLM NIMAX. Nimax is a trade mark registered in the European Union and in the U.S.
UDDEHOLM NIMAX Reliable and efficient tool steel is essential for good results. The same goes for achieving high productivity and high availability. When choosing the right steel many parameters must be
More informationORVAR SUPREME. Hot work tool steel
Hot work tool steel This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationAISI D2 Cold work tool steel
T OOL STEEL FACTS AISI D2 Cold work tool steel Great Tooling Starts Here! This information is based on our present state of knowledge and is intended to provide general notes on our products and their
More informationUDDEHOLM BALDER UDDEHOLM STEEL FOR INDEXABLE INSERT CUTTING TOOLS
Reliable and efficient steel is essential for good results. The same goes for achieving high productivity and high availability. When choosing the right steel many parameters must be considered, by using
More informationUDDEHOLM NIMAX. Uddeholm Nimax
Uddeholm Nimax UDDEHOLM NIMAX Reliable and efficient tool steel is essential for good results. The same goes for achieving high productivity and high availability. When choosing the right steel many parameters
More informationUddeholm Formvar. FORMVAR is a trade mark registered in the European Union
Uddeholm Formvar FORMVAR is a trade mark registered in the European Union UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes without permission of the copyright
More informationGeneral. Properties Physical data. Applications. Compressive strength. Corrosion resistance
UDDEHOLM ELMAX This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty of
More informationUddeholm Vanax SuperClean. Uddeholm Vanax SuperClean
Uddeholm Vanax SuperClean 1 Vanax is a trade mark registered in the European Union and in the U.S. UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes without
More informationCALMAX. Plastic mould and cold work steel
Plastic mould and cold work steel General CALMAX is a chromium-molybdenum-vanadium alloyed steel characterized by: High toughness Good wear resistance Good through hardening properties Good dimensional
More informationUDDEHOLM TOOL HOLDER CONCEPT
Uddeholm Idun Uddeholm Idun Reliable and efficient steel is essential for good results. The same goes for achieving high productivity and high availability. When choosing the right steel many parameters
More informationRoyAlloy. Uddeholm RoyAlloy
RoyAlloy Uddeholm RoyAlloy REFERENCE STANDARD AISI WNr. JIS ASSAB DF-3 ARNE O1 1.2510 SKS 3 ASSAB XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 ASSAB XW-10 RIGOR A2 1.2363 SKD 12 ASSAB XW-42 SVERKER 21 D2 1.2379
More informationUDDEHOLM TOOL HOLDER CONCEPT
Uddeholm Idun Uddeholm Idun Reliable and efficient steel is essential for good results. The same goes for achieving high productivity and high availability. When choosing the right steel many parameters
More informationRoyAlloy. Uddeholm RoyAlloy
RoyAlloy Uddeholm RoyAlloy REFERENCE STANDARD AISI WNr. JIS ASSAB DF-3 ARNE O1 1.2510 SKS 3 ASSAB XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 ASSAB XW-10 RIGOR A2 1.2363 SKD 12 ASSAB XW-42 SVERKER 21 D2 1.2379
More informationMATERIALIZING VISIONS. Bohler-Uddeholm M42 HIGH SPEED STEEL
MATERIALIZING VISIONS Bohler-Uddeholm M42 HIGH SPEED STEEL General Cobalt-alloyed, molybdenum high speed steel possessing high hardness, excellent cutting properties, exceptional compressive strength,
More informationSS-EN ISO 9001 SS-EN ISO 14001
UDDEHOLM UNIMAX This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty of
More informationDF-2 ARNE O SKS 3 DF-3 O SKS 3 XW-5 SVERKER 3 D6 (D3) (1.2436) (SKD 2) XW-10 RIGOR A SKD 12 XW-41 SVERKER 21 D2 1.
REFERENCE STANDARD AISI DIN JIS DF-2 ARNE O1 1.2510 SKS 3 DF-3 O1 1.2510 SKS 3 XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 XW-10 RIGOR A2 1.2363 SKD 12 XW-41 SVERKER 21 D2 1.2379 SKD 11 XW-42 D2 1.2379 SKD 11
More informationUddeholm Sverker 3. Classified according to EU Directive 1999/45/EC For further information see our Material Safety Data Sheets. Edition 8, 06.
Uddeholm Sverker 3 UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes without permission of the copyright holder. This information is based on our present
More informationVANADIS 6 SuperClean
T O O L S T E E L F A C T S SuperClean High performance powder metallurgical cold work tool steel Great Tooling Starts Here! Cover photo: Powder pressing punch of. Excellent results have been obtained
More informationUDDEHOLM ORVAR SUPREME
UDDEHOLM ORVAR SUPREME Uddeholm Orvar Supreme can be regarded as an all-round steel used in several application areas. Except for hot work application areas the steel is also used in moulds for plastics
More informationEdition 5, The latest revised edition of this brochure is the English version, which is always published on our web site
UDDEHOLM SVERKER 3 This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationPRELIMINARY BROCHURE. Uddeholm Caldie
PRELIMINARY BROCHURE Uddeholm Caldie UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes without permission of the copyright holder. This information is based
More informationRigor is a trade mark registered in the European Union and in the U.S.
UDDEHOM RIGOR Rigor is a trade mark registered in the European Union and in the U.S. This information is based on our present state of knowledge and is intended to provide general notes on our products
More informationVanax SuperClean. Uddeholm Vanax SuperClean
Vanax SuperClean Uddeholm Vanax SuperClean ASSAB is a trademark of voestalpine High Performance Metals Pacific Pte Ltd. The information contained herein is based on our present state of knowledge and is
More informationUddeholm Vanadis 30 SuperClean. Uddeholm Vanadis 30 SuperClean
Uddeholm Vanadis 30 SuperClean 1 UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes without permission of the copyright holder. This information is based
More informationUDDEHOLM QRO 90 SUPREME
UDDEHOLM QRO 90 SUPREME This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationALUMEC. High strength aluminium
High strength aluminium This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationNIMAX. uddeholm NIMAX
uddeholm REFERENCE STANDARD AISI DIN JIS DF-2 ARNE O1 1.2510 SKS 3 DF-3 O1 1.2510 SKS 3 XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 XW-10 RIGOR A2 1.2363 SKD 12 XW-41 SVERKER 21 D2 1.2379 SKD 11 XW-42 D2 1.2379
More informationUddeholm Sleipner. Uddeholm Sleipner
Uddeholm Sleipner 1 UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes without permission of the copyright holder. This information is based on our present
More informationEdition 7, The latest revised edition of this brochure is the English version, which is always published on our web site
This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty of specific properties
More informationVANADIS 10 SuperClean High performance powder metallurgical cold work tool steel
SuperClean High performance powder metallurgical cold work tool steel Critical tool steel properties for GOOD TOOL PERFORMANCE Correct hardness for the application Very high wear resistance Sufficient
More informationUDDEHOLM ORVAR SUPREME
UDDEHOLM ORVAR SUPREME Uddeholm Orvar Supreme can be regarded as an all-round steel used in several application areas. Except for hot work application areas the steel is also used in moulds for plastics
More informationUDDEHOLM VANADIS 6 SUPERCLEAN
UDDEHOLM VANADIS 6 SUPERCLEAN UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes without permission of the copyright holder. This information is based on
More informationUDDEHOLM ORVAR SUPERIOR
UDDEHOLM ORVAR SUPERIOR UDDEHOLM ORVAR SUPERIOR Uddeholm Orvar Superior can be regarded as an all-round steel used in several application areas. Except for hot work application areas the steel is also
More informationEdition 9, The latest revised edition of this brochure is the English version, which is always published on our web site
UDDEHOLM SLEIPNER This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationUddeholm Coolmould Coolmould eng 1706 e1.indd :34
Uddeholm Coolmould Coolmould is trademark registered in the European Union. UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes This information is based on
More informationUddeholm Orvar Supreme
Uddeholm Orvar Supreme Uddeholm Orvar Supreme Uddeholm Orvar Supreme can be regarded as an all-round steel used in several application areas. Except for hot work application areas the steel is also used
More informationSS-EN ISO 9001 SS-EN ISO 14001
UDDEHOLM VANADIS 60 This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationASSAB 718 HH IMPAX HH
uddeholm IMPAX HH REFERENCE STANDARD AISI DIN JIS DF-2 ARNE O1 1.2510 SKS 3 DF-3 O1 1.2510 SKS 3 XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 XW-10 RIGOR A2 1.2363 SKD 12 XW-41 SVERKER 21 D2 1.2379 SKD 11 XW-42
More informationUDDEHOLM VANCRON 40 SS-EN ISO 9001 SS-EN ISO 14001
UDDEHOLM VANCRON 40 Uddeholm Vancron 40 is a nitrided powder tool steel, which means that a surface coating is already integrated into the finished tooling material. The result is a tool surface with very
More informationDIEVAR. Uddeholm Dievar
DIEVAR Uddeholm Dievar REFERENCE STANDARD AISI WNr. JIS ASSAB DF-3 ARNE O1 1.2510 SKS 3 ASSAB XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 ASSAB XW-10 RIGOR A2 1.2363 SKD 12 ASSAB XW-42 SVERKER 21 D2 1.2379 SKD
More informationUddeholm Sverker 21. Classified according to EU Directive 1999/45/EC For further information see our Material Safety Data Sheets.
Uddeholm Sverker 21 UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes without permission of the copyright holder. This information is based on our present
More informationCORRAX UDDEHOLM CORRAX
UDDEHOLM REFERENCE STANDARD AISI WNr. JIS ASSAB DF-2 ARNE O1 (1.2510 (SKS 3 ASSAB DF-3 O1 (1.2510 (SKS 3 ASSAB XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 ASSAB XW-10 RIGOR A2 1.2363 SKD 12 ASSAB XW-41 SVERKER
More informationASSAB M UDDEHOLM ORVAR 2 MICRODIZED
ASSAB 8407 2M UDDEHOLM ORVAR 2 MICRODIZED REFERENCE STANDARD AISI WNr. JIS ASSAB DF-3 ARNE O1 1.2510 SKS 3 ASSAB XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 ASSAB XW-10 RIGOR A2 1.2363 SKD 12 ASSAB XW-42 SVERKER
More informationClassified according to EU Directive 1999/45/EC For further information see our Material Safety Data Sheets.
This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty of specific properties
More informationUDDEHOLM VANADIS 23 SUPERCLEAN
UDDEHOLM VANADIS 23 SUPERCLEAN UDDEHOLM VANADIS 23 SUPERCLEAN Uddeholm Vanadis 23 SuperClean is a high alloyed powder metallurgical high speed steel corresponding to AISI M3:2 with a very good abrasive
More informationASSAB DF-2 ARNE O1 (1.2510) (SKS 3) ASSAB DF-3 O1 (1.2510) (SKS 3) ASSAB XW-5 SVERKER 3 D6 (D3) (1.2436) (SKD 2) ASSAB XW-10 RIGOR A2 1.
Edition 140205 REFERENCE STANDARD AISI WNr. JIS ASSAB DF-2 ARNE O1 (1.2510 (SKS 3 ASSAB DF-3 O1 (1.2510 (SKS 3 ASSAB XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 ASSAB XW-10 RIGOR A2 1.2363 SKD 12 ASSAB XW-41
More informationUddeholm Vanadis 23 SuperClean
Uddeholm Vanadis 23 SuperClean Uddeholm Vanadis 23 SuperClean Uddeholm Vanadis 23 SuperClean is a high alloyed powder metallurgical high speed steel corresponding to AISI M3:2 with a very good abrasive
More informationMOLDMAX High strength beryllium copper mould alloy
High strength beryllium copper mould alloy General MOLDMAX is a high-strength beryllium copper mould alloy made by Brush Wellman Inc. for plastics moulding applications. Its main properties include: high
More informationPRELIMINARY BROCHURE. Uddeholm Vanadis 8 SuperClean
PRELIMINARY BROCHURE Uddeholm Vanadis 8 SuperClean UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes without permission of the copyright holder. This information
More informationASSAB DF-2 ARNE O1 (1.2510) (SKS 3) ASSAB DF-3 O1 (1.2510) (SKS 3) ASSAB XW-5 SVERKER 3 D6 (D3) (1.2436) (SKD 2) ASSAB XW-10 RIGOR A2 1.
REFERENCE STANDARD AISI WNr. JIS ASSAB DF-2 ARNE O1 (1.2510 (SKS 3 ASSAB DF-3 O1 (1.2510 (SKS 3 ASSAB XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 ASSAB XW-10 RIGOR A2 1.2363 SKD 12 ASSAB XW-41 SVERKER 21 D2 1.2379
More informationASSAB 8407 Supreme. Uddeholm Orvar Supreme
ASSAB 8407 Supreme Uddeholm Orvar Supreme REFERENCE STANDARD AISI WNr. JIS ASSAB DF-3 ARNE O1 1.2510 SKS 3 ASSAB XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 ASSAB XW-10 RIGOR A2 1.2363 SKD 12 ASSAB XW-42 SVERKER
More informationUddeholm Vanadis 4 Extra SuperClean. Uddeholm Vanadis 4 Extra SuperClean
Uddeholm Vanadis 4 Extra SuperClean 1 Uddeholm Vanadis 4 Extra SuperClean CONSISTENT TOOL PERFORMANCE LONG AND RELIABLE TOOL LIFE With an increased demand for just in time deliveries (JIT and shorter lead
More informationUddeholm QRO 90 Supreme
Uddeholm QRO 90 Supreme UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes without permission of the copyright holder. This information is based on our present
More informationQRO 90 SUPREME QRO 90 SUPREME
uddeholm QRO 90 SUPREME REFERENCE STANDARD AISI DIN JIS DF-2 ARNE O1 1.2510 SKS 3 DF-3 O1 1.2510 SKS 3 XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 XW-10 RIGOR A2 1.2363 SKD 12 XW-41 SVERKER 21 D2 1.2379 SKD 11
More informationUDDEHOLM VANCRON 40 SUPERCLEAN
UDDEHOLM VANCRON 40 SUPERCLEAN UDDEHOLM VANCRON 40 SUPERCLEAN Uddeholm Vancron 40 SuperClean is a nitrided powder tool steel, which means that a surface coating is already integrated into the finished
More informationELMAX SuperClean Uddeholm Elmax SuperClean
ELMAX SuperClean Uddeholm Elmax SuperClean REFERENCE STANDARD AISI WNr. JIS ASSAB DF-2 ARNE O1 (1.2510 (SKS 3 ASSAB DF-3 O1 (1.2510 (SKS 3 ASSAB XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 ASSAB XW-10 RIGOR A2
More informationuddeholm CALMAX CALMAX
uddeholm REFERENCE STANDARD AISI DIN JIS DF-2 ARNE O1 1.2510 SKS 3 DF-3 O1 1.2510 SKS 3 XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 XW-10 RIGOR A2 1.2363 SKD 12 XW-41 SVERKER 21 D2 1.2379 SKD 11 XW-42 D2 1.2379
More informationQRO 90 SUPREME UDDEHOLM QRO 90 SUPREME
UDDEHOLM QRO 90 SUPREME REFERENCE STANDARD AISI WNr. JIS ASSAB DF-2 ARNE O1 (1.2510 (SKS 3 ASSAB DF-3 O1 (1.2510 (SKS 3 ASSAB XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 ASSAB XW-10 RIGOR A2 1.2363 SKD 12 ASSAB
More informationMIRRAX ESR. Uddeholm Mirrax ESR
MIRRAX ESR Uddeholm Mirrax ESR REFERENCE STANDARD AISI WNr. JIS ASSAB DF-3 ARNE O1 1.2510 SKS 3 ASSAB XW-5 SVERKER 3 D6 (D3) (1.2436) (SKD 2) ASSAB XW-10 RIGOR A2 1.2363 SKD 12 ASSAB XW-42 SVERKER 21 D2
More informationPLASTIC MOULD STEEL RS 100
PLASTIC MOULD STEEL RS 100 PLASTIC MOULD STEEL Family of RS plastic mould steel RS grade W.Nr. DIN AISI RS 100 1.2312 40CrMnMoS8-6 ~P20 RS 101 1.2311 40CrMnMo7 ~P20 RS 103 1.2738 40CrMnNiMo8-6-1 RS 105
More informationVIDAR 1 ESR UDDEHOLM VIDAR 1 ESR
UDDEHOLM VIDAR 1 ESR REFERENCE STANDARD AISI WNr. JIS ASSAB DF-2 ARNE O1 (1.2510 (SKS 3 ASSAB DF-3 O1 (1.2510 (SKS 3 ASSAB XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 ASSAB XW-10 RIGOR A2 1.2363 SKD 12 ASSAB
More informationROYALLOY UDDEHOLM ROYALLOY
UDDEHOLM ROYALLOY REFERENCE STANDARD AISI WNr. JIS ASSAB DF-2 ARNE O1 (1.2510 (SKS 3 ASSAB DF-3 O1 (1.2510 (SKS 3 ASSAB XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 ASSAB XW-10 RIGOR A2 1.2363 SKD 12 ASSAB XW-41
More informationPlastic Molding Applications
Plastic Molding Applications Plastic Injection Molding Comprehensive Product Range Böhler-Uddeholm mold steel grades have been developed specifically to meet the demanding requirements of the plastics
More informationVanadis 10 SuperClean Uddeholm Vanadis 10 SuperClean
Vanadis 10 SuperClean Uddeholm Vanadis 10 SuperClean REFERENCE STANDARD AISI WNr. JIS ASSAB DF-2 ARNE O1 (1.2510 (SKS 3 ASSAB DF-3 O1 (1.2510 (SKS 3 ASSAB XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 ASSAB XW-10
More informationSTAVAX ESR. Uddeholm Stavax ESR
STAVAX ESR Uddeholm Stavax ESR REFERENCE STANDARD AISI WNr. JIS ASSAB DF-3 ARNE O.250 SKS 3 ASSAB XW-5 SVERKER 3 D6 (D3) (.2436) (SKD 2) ASSAB XW-0 RIGOR A2.2363 SKD 2 ASSAB XW-42 SVERKER 2 D2.2379 SKD
More informationASSAB ASP 60. uddeholm
uddeholm Vanadis 60 REFERENCE STANDARD AISI DIN JIS DF-2 ARNE O1 1.2510 SKS 3 DF-3 O1 1.2510 SKS 3 XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 XW-10 RIGOR A2 1.2363 SKD 12 XW-41 SVERKER 21 D2 1.2379 SKD 11 XW-42
More informationDF-2 ARNE O SKS 3 DF-3 O SKS 3 XW-5 SVERKER 3 D6 (D3) (1.2436) (SKD 2) XW-10 RIGOR A SKD 12 XW-41 SVERKER 21 D2 1.
REFERENCE STANDARD AISI DIN JIS DF-2 ARNE O1 1.2510 SKS 3 DF-3 O1 1.2510 SKS 3 XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 XW-10 RIGOR A2 1.2363 SKD 12 XW-41 SVERKER 21 D2 1.2379 SKD 11 XW-42 D2 1.2379 SKD 11
More informationCALDIE UDDEHOLM CALDIE
CALDIE UDDEHOLM CALDIE REFERENCE STANDARD AISI WNr. JIS ASSAB DF-3 ARNE O1 1.2510 SKS 3 ASSAB XW-5 SVERKER 3 D6 (D3) (1.2436) (SKD 2) ASSAB XW-10 RIGOR A2 1.2363 SKD 12 ASSAB XW-42 SVERKER 21 D2 1.2379
More informationASSAB XW-5 UDDEHOLM SVERKER 3
UDDEHOLM SVERKER 3 REFERENCE STANDARD AISI WNr. JIS ASSAB DF-2 ARNE O1 (1.2510 (SKS 3 ASSAB DF-3 O1 (1.2510 (SKS 3 ASSAB XW-5 SVERKER 3 D6 (D3 (1.2436 (SKD 2 ASSAB XW-10 RIGOR A2 1.2363 SKD 12 ASSAB XW-41
More informationAPM 2730 HOT ISOSTATIC PRESSED (HIP) PRODUCTS
APM 2730 HOT ISOSTATIC PRESSED (HIP) PRODUCTS DATASHEET APM 2730 is a high alloyed powder metallurgical high speed steel corresponding to ASTM M3:2 +Co with a combination of very good abrasive wear resistance,
More informationSTAVAX ESR. Uddeholm Stavax ESR
STAVAX ESR Uddeholm Stavax ESR REFERENCE STANDARD AISI WNr. JIS ASSAB DF-3 ARNE O.25 SKS 3 ASSAB XW-5 SVERKER 3 D6 (D3) (.2436) (SKD 2) ASSAB XW- RIGOR A2.2363 SKD 2 ASSAB XW-42 SVERKER 2 D2.2379 SKD CARMO
More informationASSAB 88. Uddeholm Sleipner
ASSAB 88 Uddeholm Sleipner REFERENCE STANDARD AISI WNr. JIS ASSAB DF-3 ARNE O1 1.2510 SKS 3 ASSAB XW-5 SVERKER 3 D6 (D3) (1.2436) (SKD 2) ASSAB XW-10 RIGOR A2 1.2363 SKD 12 ASSAB XW-42 SVERKER 21 D2 1.2379
More information