MATERIAL SAFETY DATA SHEET Complies with OSHA Hazard Communication Standard 29 CFR

Transcription

1 MATERIAL SAFETY DATA SHEET Complies with OSHA Hazard Communication Standard 29 CFR Product Type: Desoldering Braid Emergency Contact: Chemtrec Product Name: GC Solder/Braid Part B Phone (24 hours): (800) Part Number(s): Section 1 - Identification of Product HMIS Rating Least 0 Health 1 Slight 1 Flammability 0 Moderate 2 Reactivity 0 High 3 Extreme 4 Rosin flux may cause an allergic reaction, resulting in a skin rash. Clean hands after use. Section 2 - Hazardous Ingredients ACGIH CAS# % TLV Pure Copper Metal fume 0.1mg/m3 dust 1.0mg/m3 Modified Rosin The 0.1% Rosin may cause allergic reactions: does not contain hazardous ingredients. Section 3 - Physical Data Appearance: Copper metallic braid with fine crystalline resin layer. Odor: ph: Boiling Point: 1981ºF Melting Point: 1949ºF Flash Point: No flash Flammability (solid gas): Auto-flammability: Explosive Properties: Oxidizing Properties: Capper can oxidize if prolonged exposure in moist conditions. Vapor Pressure: Relative Density: Solubility: Water solubility-negligible Fat solubility-unknown Partition coefficient, n-octanol/water: Part Number(s): / Part B Page 1 of 4

2 Other Data: Safety Parameters: Vapor Density: Miscibility: Evaporation Rate: Conductivity: Viscosity: Copper is very conductive A solid Section 4 - Fire & Explosion Hazard Data Suitable Extinguishing Media: Unsuitable Extinguishing Media: Exposure Hazards: Combustion Products-Resulting Gases: Protective Equipment for Fire Fighters: Powder Dolomite, Sodium Chloride, or Graphite Do not use water Copper reacts violently with C2H2, NH 4N03, Bromates, Chlorates, Iodates, C12, C1F2, Ethylene Oxide, F2, H202, Hydrazine monoitrate, Hydrazoic acid, H2S, K202, NaN3, Na202, CUN03, S. Carbon Monoxide, Aliphatic Aldehydes, and Acids. Not needed Section 5 - Health Hazard Data Effects of Exposure: Skin: Eye: Inhalation: Ingestion: First Aid Measures: Skin: Eye: Ingestion: Possible allergic rash reaction. Possible danger of metal fragments. If product is exposed to temperatures in excess of 180ºF, local ventilation must be used. May be moderately irritating to stomach lining. Induce vomiting if conscious. Flush skin with copious amounts of water. Remove metal fragments and flush eyes with water. Remove to fresh air. If breathing has stopped, administer CPR. Induce vomiting. Wire strands could cause internal digestive tract bleeding. Induce vomiting. Section 6 - Reactivity Data Stability: Materials and Conditions to Avoid: Hazardous Decomposition of Product: Stable Hazardous environment can occur in the presence of excessive heat and/or chemicals as listed in Section 4, this document. Part Number(s): / Part B Page 2 of 4

3 Section 7 - Spill or Leak Procedures Accidental Release Measures: Personal: Environmental Precautions: When subjected to temperatures over 180ºF, flux fumes should be vented. General mechanical or local hood. Ventilation is recommended for applications where the product will exceed 180ºF. Vacuum or sweep up and dispose of as a non-combustible metal. Gloves not normally required. When clipping short lengths, protective eyewear is recommended. Section 8 - Special Protection Information System Design (e.g. Fume Hoods, Ventilated Cabinets, Enclosure) Personal Protection: Respiratory Protection: Hand Protection: Eye Protection: Skin Protection: General mechanical or local hood. Ventilation is recommended for applications where the product will exceed 180º F. Use local or general ventilation away from the operator if the product temperature is exposed to 180 F+. Gloves may be used if resin is a skin irritant. Eye protection should be worn when clipping short lengths. See hand protection. Section 9 Special Precautions Handling and Storage: To Prevent Airborne Levels: Safe Handling: Store in cool, dry environment for functional purposes. If product is exposed to temperatures that are above 180ºF, use local ventilation. required. Consult with local regulatory bodies to metallic solid waste disposal. Section 10 - Regulatory Information Precautionary Label Information: Symbols: Risk Phrases: Safety Phrases: CEN Standards: This product does not require warning labels due to hazards classification as designated in Section 1. R36/37/38 S14 (per section 4), S22/39, S43 (per section 4) Carcinogens <0.1% Section 11 - Other Information Transportation Information: UN Number: Proper Shipping Name: Harmonized Tariff Code: # Copper wire coated with resin flux. Validated license #/ General license symbol: NLR Part Number(s): / Part B Page 3 of 4

4 Disclaimer GC/Waldom Electronics, Inc. believes that the information contained herein is accurate and reliable as of the date of this material safety data sheet, but no representation guarantee or warranty, express or implied, is made as to the accuracy, reliability, or completeness of the information. Persons receiving this information are encouraged to make their own determination as to the information s suitability and completeness for their particular application. NO INFORMATION CONTAINED HEREIN CONSTITUTES A PRODUCT WARRANTY OF ANY KIND, WHETHER EXPRESS OR IMPLIED; AND ALL IMPLIED WARRANTIES OF MERCHANT ABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED BY GC/WALDOM ELECTRONICS, INC. Part Number(s): / Part B Page 4 of 4

5 MATERIAL SAFETY DATA SHEET Complies with OSHA Hazard Communication Standard 29 CFR Product Type: Desoldering Braid Emergency Contact: Chemtrec Product Name: GC Solder/Braid Part B Phone (24 hours): (800) Part Number(s): Section 1 - Identification of Product HMIS Rating Least 0 Health 1 Slight 1 Flammability 0 Moderate 2 Reactivity 0 High 3 Extreme 4 Rosin flux may cause an allergic reaction, resulting in a skin rash. Clean hands after use. Section 2 - Hazardous Ingredients ACGIH CAS# % TLV Pure Copper Metal fume 0.1mg/m3 dust 1.0mg/m3 Modified Rosin The 0.1% Rosin may cause allergic reactions: does not contain hazardous ingredients. Section 3 - Physical Data Appearance: Copper metallic braid with fine crystalline resin layer. Odor: ph: Boiling Point: 1981ºF Melting Point: 1949ºF Flash Point: No flash Flammability (solid gas): Auto-flammability: Explosive Properties: Oxidizing Properties: Capper can oxidize if prolonged exposure in moist conditions. Vapor Pressure: Relative Density: Solubility: Water solubility-negligible Fat solubility-unknown Partition coefficient, n-octanol/water: Part Number(s): / Part B Page 1 of 4

6 Other Data: Safety Parameters: Vapor Density: Miscibility: Evaporation Rate: Conductivity: Viscosity: Copper is very conductive A solid Section 4 - Fire & Explosion Hazard Data Suitable Extinguishing Media: Unsuitable Extinguishing Media: Exposure Hazards: Combustion Products-Resulting Gases: Protective Equipment for Fire Fighters: Powder Dolomite, Sodium Chloride, or Graphite Do not use water Copper reacts violently with C2H2, NH 4N03, Bromates, Chlorates, Iodates, C12, C1F2, Ethylene Oxide, F2, H202, Hydrazine monoitrate, Hydrazoic acid, H2S, K202, NaN3, Na202, CUN03, S. Carbon Monoxide, Aliphatic Aldehydes, and Acids. Not needed Section 5 - Health Hazard Data Effects of Exposure: Skin: Eye: Inhalation: Ingestion: First Aid Measures: Skin: Eye: Ingestion: Possible allergic rash reaction. Possible danger of metal fragments. If product is exposed to temperatures in excess of 180ºF, local ventilation must be used. May be moderately irritating to stomach lining. Induce vomiting if conscious. Flush skin with copious amounts of water. Remove metal fragments and flush eyes with water. Remove to fresh air. If breathing has stopped, administer CPR. Induce vomiting. Wire strands could cause internal digestive tract bleeding. Induce vomiting. Section 6 - Reactivity Data Stability: Materials and Conditions to Avoid: Hazardous Decomposition of Product: Stable Hazardous environment can occur in the presence of excessive heat and/or chemicals as listed in Section 4, this document. Part Number(s): / Part B Page 2 of 4

7 Section 7 - Spill or Leak Procedures Accidental Release Measures: Personal: Environmental Precautions: When subjected to temperatures over 180ºF, flux fumes should be vented. General mechanical or local hood. Ventilation is recommended for applications where the product will exceed 180ºF. Vacuum or sweep up and dispose of as a non-combustible metal. Gloves not normally required. When clipping short lengths, protective eyewear is recommended. Section 8 - Special Protection Information System Design (e.g. Fume Hoods, Ventilated Cabinets, Enclosure) Personal Protection: Respiratory Protection: Hand Protection: Eye Protection: Skin Protection: General mechanical or local hood. Ventilation is recommended for applications where the product will exceed 180º F. Use local or general ventilation away from the operator if the product temperature is exposed to 180 F+. Gloves may be used if resin is a skin irritant. Eye protection should be worn when clipping short lengths. See hand protection. Section 9 Special Precautions Handling and Storage: To Prevent Airborne Levels: Safe Handling: Store in cool, dry environment for functional purposes. If product is exposed to temperatures that are above 180ºF, use local ventilation. required. Consult with local regulatory bodies to metallic solid waste disposal. Section 10 - Regulatory Information Precautionary Label Information: Symbols: Risk Phrases: Safety Phrases: CEN Standards: This product does not require warning labels due to hazards classification as designated in Section 1. R36/37/38 S14 (per section 4), S22/39, S43 (per section 4) Carcinogens <0.1% Section 11 - Other Information Transportation Information: UN Number: Proper Shipping Name: Harmonized Tariff Code: # Copper wire coated with resin flux. Validated license #/ General license symbol: NLR Part Number(s): / Part B Page 3 of 4

8 Disclaimer GC/Waldom Electronics, Inc. believes that the information contained herein is accurate and reliable as of the date of this material safety data sheet, but no representation guarantee or warranty, express or implied, is made as to the accuracy, reliability, or completeness of the information. Persons receiving this information are encouraged to make their own determination as to the information s suitability and completeness for their particular application. NO INFORMATION CONTAINED HEREIN CONSTITUTES A PRODUCT WARRANTY OF ANY KIND, WHETHER EXPRESS OR IMPLIED; AND ALL IMPLIED WARRANTIES OF MERCHANT ABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED BY GC/WALDOM ELECTRONICS, INC. Part Number(s): / Part B Page 4 of 4