Current Standard Plates including Transmittal Letters are available on the web at:
|
|
- Matilda Jefferson
- 6 years ago
- Views:
Transcription
1 MINNESOTA DEPARTMENT OF TRANSPORTATION DEVELOPED BY: Design Standards ISSUED BY: Office of Project Management and Technical Support, Design Support Section TRANSMITTAL LETTER NO. (6-03) MANUAL: Standard Plates DATED: September 2, 206 SUBJECT: Standard Plates 407, 40, 440, 72, 8343 Minor revisions The following Standard Plates have been revised: 407C Catch Basin 40F Cover Casting for Manhole 440D Special Grate Castings for Catch Basin 72C - Installation & Reinforcement of Catch Basin & Manhole Castings 8343A - High-Tension Cable Barrier Line Post Foundation INSTRUCTIONS: Record the transmittal letter number, date, and subject on the transmittal record sheet located in the front of the manual. The previous Transmittal Letter No. issued for this manual was 6-02, dated July 26, 206. Remove from the Standard Plate manual: Standard Plate 407C (Rev ), 408 back Standard Plate 40F (Appr ) Standard Plate 440D (Rev ), 443 back Standard Plate 72C (Rev ), 7 front Standard Plate 8343A (Appr ) Insert into the Standard Plate manual: Standard Plate 407C (Rev ) Standard Plate 408B (Appr ) Standard Plate 40F (Rev ) Standard Plate 440D (Rev ) Standard Plate 443E (Rev ) Standard Plate 7J (Rev ) Standard Plate 72C (Rev ) Standard Plate 8343A (Rev ) Current Standard Plates including Transmittal Letters are available on the web at: Direct any technical questions regarding this transmittal to Ron Reemer, Design Standards Unit at (65) Michael Elle, P.E. Design Standards Engineer
2 THIS PAGE INTENTIONALLY LEFT BLANK
3 Summary of Changes Various Standard Plates Minor Revisions Transmittal Letter No. (6-03) 407C:. Circled note # (local note flag) was previously omitted from the notes (bottom right). 40F:. General note changed from Casting No to Casting No D:. General note changed from Casting No to Casting No C:. Removed last sentence of circled note A:. Added (Optional) to circled note 3.
4 THIS PAGE INTENTIONALLY LEFT BLANK
5 VIEW A-A :6 SLOPE DESIRABLE ROADWAY SHOULDER REINFORCED CONCRETE PIPE - CLASS II ( SEE STANDARD PLATE 3000 ) EARTH DITCH BLOCK 8'' MIN. 6'' A ( SOD SLOPES ) :6 8'' MIN. D A CONC. APRON FOR R.C.P. CIRCULAR OR PIPE-ARCH PAY HEIGHT ELEVATION REINFORCED CONCRETE PIPE DESIGN PC CONTINUOUS WELD VIEW B-B :6 SLOPE DESIRABLE ROADWAY SHOULDER EARTH DITCH BLOCK ( SOD SLOPES ) CORRUGATED METAL PIPE :6 8'' MIN. 6'' B 8'' MIN. NOTES: D INSIDE DIAMETER OF CATCH CIRCULAR OR PIPE-ARCH B PAY HEIGHT ELEVATION METAL APRON FOR C.M.P. BASIN WILL BE INDICATED IN THE PAY ITEM. FOR USE PRINCIPALLY FOR MEDIAN DRAINAGE. ANGLE WILL BE SHOWN IN PLAN FOR ARCH PIPE. CORRUGATED METAL PIPE DESIGN PM DESIGN PC DESIGN PM STATE OF MINNESOTA DEPARTMENT OF TRANSPORTATION CATCH BASIN CONCRETE PIPE AND METAL PIPE SPECIFICATION REFERENCE 2506 REVISED M.J.E. STANDARD PLATE NO. 407C
6 THIS PAGE INTENTIONALLY LEFT BLANK
7 A A TOP VIEW TOP OF CASTING 4-/2 TYP. 48 DIA. 5 5-/2 FOR 60 DIA. 6 FOR 72 DIA FOR 60 DIA. 6 FOR 72 DIA. VARIABLE MAX. 3 5-/2 FOR 60 DIA. 8 FOR 72 DIA. 60 DIA. 72 DIA. 6 7 SECTION A-A NOTES: REINFORCING: SINGLE LINE STEEL WIRE FABRIC HAVING AN AREA OF NOT LESS THAN 0.5 SQ. IN. PER FOOT OF HEIGHT FOR 60 DIA. AND NOT LESS THAN 0.8 SQ. IN. PER FOOT OF HEIGHT FOR 72 DIA REFER TO PLANS FOR ANY STEP REQUIREMENTS. SEE STANDARD PLATES INDEX FOR OTHER APPROVED JOINTS. MANHOLE REDUCING SECTION 4 0 HIGH. WALL THICKNESS TAPERS TO PROVIDE A SMOOTH EXTERIOR. 4 THE MAXIMUM DEPTH FROM THE TOP OF THE CASTING TO THE TOP OF THE REDUCING CONE IS 0-0". DESIGN D APPROVED APRIL 6, 204 STATE OF MINNESOTA DEPARTMENT OF TRANSPORTATION SPECIFICATION REFERENCE STANDARD PLATE MANHOLE OR CATCH BASIN NO. STATE DESIGN ENGINEER REDUCER CONE SECTION PRECAST B
8 THIS PAGE INTENTIONALLY LEFT BLANK
9 MN/ 2'' MN/ -/4'' 3/8'' LIFT HOLE 7/8'' /4'' CROWN 3/8'' 4 4-5/32'' 2 /8'' RAD. TYP. THREE STACKING 7/8'' LUGS AT 20 APART /4'' RAD. TYP. CROWN 5 /8'' RAD. 2'' STACKING LUG STACKING LUG 7 VENT HOLES 5 -/4'' 3/8'' LIFT HOLE 3/8'' /32'' 4-5/32'' MAKE TREADS MAKE TREADS 3/6'' HIGH 3/6'' HIGH TOP VIEW BOTTOM VIEW TOP VIEW BOTTOM VIEW CASTING NO. 75 CASTING NO /4'' 25-3/4'' -/4'' 3/4'' LIFT 4-5/32'' HOLE 4 -/4'' -/4'' -/4'' 7/8'' 2 /8'' RAD. TYP. THREE STACKING 7/8'' LUGS AT 20 APART 5 /8'' RAD. /4'' RAD. TYP. SECTION SECTION NOTES: THESE COVERS TO BE USED WITH RING CASTING NO TO ON OPPOSITE SIDE OF TOP SURFACE PLACE CASTING NUMBER, LETTERS ( MN/DOT ) AND NUMERALS TO BE 3/4'' IN HEIGHT AND DEPRESSED /8''. 2 LIFT HOLE MACHINE FINISHED THICKNESS TO BE 3/6''. 3 COVER SHALL BE MADE OF GRAY IRON. CLASS 35B. 4 LIFT HOLE -/4'' DIA. AT THE TOP, -/2'' AT THE BOTTOM. 5 EIGHT (8) VENT HOLES IN OUTER CIRCLE. NINE (9) VENT HOLES IN INNER CIRCLE. HOLES ARE 3/4'' DIA. AT THE TOP AND '' DIA. AT THE BOTTOM. INNER CIRCLE IS 2'' FROM THE OUTER CIRCLE. /4'' CASTING NO LBS. CASTING NO LBS. APPROVED OCTOBER 25, 996 STATE OF MINNESOTA DEPARTMENT OF TRANSPORTATION SPECIFICATION REFERENCE STANDARD PLATE STATE DESIGN ENGINEER COVER CASTING FOR MANHOLE ( FOR USE IN ALL TRAFFIC AREAS ) 2506 REVISED M.J.E. NO. 40F
10 THIS PAGE INTENTIONALLY LEFT BLANK
11 MN/DOT MN/DOT 2'' 2'' A A A A -/4'' -/4'' TOP VIEW CASTING NO. 72 TOP VIEW CASTING NO ' -3/4'' DIA. 2' -3/4'' DIA. 7/8'' FINISHED THICKNESS 9 SPACES AT 2-/8'' = ' 7-/8'' 9 SPACES AT 2-/8'' = ' 7-/8'' '' 5/8'' 3/6'' '' 2'' '' 3/6'' 5/8'' R. 3/6'' 2'' MACHINE FINISHED 5/8'' /2'' 7/8'' FINISHED THICKNESS MACHINE FINISHED 5/8'' /2'' 3/6'' 5/8'' R. 2' -5/8'' DIA. 2' -5/8'' DIA. SECTION A-A CONCAVE SECTION A-A CONVEX NOTES: THESE GRATES SHALL BE USED WITH RING CASTING NO TO LETTERS ( MN/DOT ) AND NUMERALS ( 720 & 72 ) SHALL BE 3/4 INCHES IN HEIGHT AND DEPRESSED /8 INCHES. CASTING NO. 720 CASTING NO. 72 STATE OF MINNESOTA DEPARTMENT OF TRANSPORTATION SPECIAL GRATE CASTINGS FOR CATCH BASIN CONVEX AND CONCAVE SPECIFICATION REFERENCE 2506 REVISED M.J.E. STANDARD PLATE NO. 440D
12 THIS PAGE INTENTIONALLY LEFT BLANK
13 F303 CIRCULAR REINFORCE~ENT BAR, APPROX. 3' 2" DIA. F30 C TYP.l 3/4" LETTERS DEPRESSED /8" a: >- - B L B _j a: >- - TOP VIEW TOP VIEW 3'6" 4-/4" 4-3/4" ri do: : > NI- 2'0" 2'9" ' " 'N ~ ~ lcj L:Jf :< N '! ; ' I ll'l + ' goo.. " SECTION A-A EIGHT F30 BARS CSEE DETAIL! EQUALLY SPACED SECTION B-B STOOL TYPE GRATE C CASTING NO. 73 l APPROX. WEIGHT 200 LBS. REINFORCED CONCRETE FRAUE C FOR CASTING NO. 73 l ~~~s ~ F30 NOTES: FRA~E MAY BE PRECAST OR CAST-IN-PLACE. CASTING NO. 73 & FRAME APPROVED MARCH 4, 996 STATE OF MINNESOTA DEPARTMENT OF TRANSPORTATION ~JUJ)j~~ STOOL GRATE & CONCRETE FRAME SPECIFICATION REFERENCE STATE DESIGN ENGINEER ( MEDIAN DRAINS l REVISED ~.J.E STANDARD PLATE NO. 443E
14 THIS PAGE INTENTIONALLY LEFT BLANK
15 2'0" GUTTER WIDTH ' 0" -FLOW - FLOW DEPRESSION ( SUMP ) IN FLOW LINE AT CATCH BASIN LOCATION DISTANCE FROM It SHOWN IN PLANS 3" ;5 ::IIi. = 5 ""<.J 3" MIN. CLR. DESIGN D CONCRETE CURB & GUTTER DISTANCE FROM It TO FACE OF CURB SHOWN IN PLANS 2' 0" GUTTER WIDTH W A CURB DESIGN B CONCRETE CURB & GUTTER CURB BOX CASTINGS USED FOR ASSEMBLY 82B, 823A, 824, 83A & 833A DISTANCE FROM It TO FACE OF CURB SHOWN IN PLANS DISTANCE FROM It SHOWN IN PLANS 2'0" DESIGN B CONCRETE CURB A CURB WIDTH ONE NO. 4 X 5'LONG ~--fi;..t--{5 BAR PLACED THROUGH LUG HOLES, NOTES: COMPENSATE FOR TILT BY VARYING THE DEPTH OF MORTAR SEAT. DETAILS ARE TYPICAL AND APPLY TO INSTALLATION OF BOTH TELESCOPING AND NON-TELESCOPING CASTINGS. REFER TO PLANS FOR SPECIFIC ITEMS REQUIRED. ALL REINFORCEMENT REQUIRED IS INCIDENTAL, WITH NO DIRECT PAYMENT. CD CATCH BASIN ALL APPLICATIONS USE.0' SUMP. SUMP SHALL BE MEASURED AT CENTER OF THICKNESS AS ADJACENT PAVEMENT OR NO. 4 HORIZONTAL BARS 5' 0" LONG CENTERED ABOUT It OF CURB INLET CASTING SHALL BE FASTENED TEMPORARILY TO FRAME CASTING WITH 2 CAP SCREWS, DURING CURB CONSTRUCTION. CAP SCREWS MUST BE REMOVED AFTER CURB HAS HARDENED. APPROVED APRIL 23, 996 STATE OF MINNESOTA DEPARTMENT OF TRANSPORTATION ~JUJ)J.I(~ STATE DESIGN ENGINEER INSTALLATION OF CATCH BASIN CASTINGS CONCRETE CURB & GUTTER SPECIFICATION REFERENCE 253 REVISED M.J.E. STANDARD PLATE NO. 7J
16 THIS PAGE INTENTIONALLY LEFT BLANK
17 FLOW 3' 0'' 3' 0'' 2 FLOW 45 TYP. 4'' BACK OF CURB 45 TYP. 4'' BACK OF CURB TOP OF CURB 3 CATCH BASIN LOW POINT LOCATION DEPRESSION ( SUMP ) IN FLOW LINE AT CATCH BASIN LOCATION A 4'' A B 4'' B CATCH BASIN CATCH BASIN LONGITUDINAL JOINT TWO NO. 5 BARS, 6' LONG 4'' 4'' 2-NO NO. 4 -/2'' CLR. -NO. 4 -/2'' CLR. CONTRACTION JOINT CATCH 5 5 BASIN OR MANHOLE 5 KEYWAY TWO NO. 5 BARS 6' LONG DESIGN B, S OR V CURB DESIGN D CURB KEYWAY PLAN VIEW CATCH BASIN WITH DESIGN B, S OR V CURB PLAN VIEW CATCH BASIN WITH DESIGN D CURB TWO NO. 5 BARS, 6' LONG PLAN VIEW ( MANHOLES ) DISTANCE FROM < TO FACE DISTANCE FROM < OF CURB SHOWN IN PLANS A CURB WIDTH SHOWN IN PLANS < CASTING CLR. 3' MIN. 2' 0'' 2' 0'' ' 0'' 5'' 4'' 2 ONE NO. 4 X 5' 0'' LONG BAR SHALL 5'' 4'' 2 BE PLACED THROUGH CORED HOLES IN LUGS. 4 DISTANCE FROM < SHOWN IN PLANS SECTION A-A < STRUCTURE DESIGN B CURB SHOWN THREE NO. 4 HORIZ. BARS 5' 0'' LONG CENTERED ABOUT < OF CASTING SECTION B-B DESIGN D CURB SHOWN 3'' 3' MIN. CLR. 3'' MIN. CLR. CURB DESIGN CURB BOX CASTING B, S & V 82B, 822 & 83A B & V 823A & 833A B 824 & 825 ADDITIONAL SLAB REINF. - TWO NO. 5 BARS 6' 0'' LONG, SPACED AT 5'' CENTERS. PLACE DIRECTLY BELOW TYPICAL SLAB REINF. AT LOCATIONS SHOWN. NOTES: COMPENSATE FOR TILT BY VARYING THE DEPTH OF MORTAR SEAT. DETAILS ARE TYPICAL AND APPLY TO INSTALLATION OF BOTH TELESCOPING AND NON-TELESCOPING CASTINGS. REFER TO PLANS FOR SPECIFIC ITEMS REQUIRED. REINFORCEMENT BARS SHALL BE GRADE 60. ALL REINFORCEMENT REQUIRED IS INCIDENTAL, WITH NO DIRECT PAYMENT. 2 ON ALL APPLICATIONS USE.0' SUMP. SUMP SHALL BE MEASURED AT CENTER OF CASTING. 3 SAME THICKNESS AS ADJACENT PAVEMENT OR GUTTER. 4 CURB INLET CASTING TO BE FASTENED TEMPORARILY TO FRAME CASTING WITH 2 CAP SCREWS, DURING CURB CONSTRUCTION. CAP SCREWS MUST BE REMOVED AFTER CURB HAS HARDENED. 5 WHEN PAVEMENT JOINTS ARE WITHIN 0'' OF CATCH BASIN OR MANHOLE, BOX IN OPENING WITH KEYWAY JOINT. APPROVED APRIL 23, 996 STATE OF MINNESOTA DEPARTMENT OF TRANSPORTATION SPECIFICATION REFERENCE STANDARD PLATE INSTALLATION & REINFORCEMENT OF 253 NO. STATE DESIGN ENGINEER CATCH BASIN & MANHOLE CASTINGS CONCRETE INTEGRANT CURBS REVISED M.J.E. 72C
18 THIS PAGE INTENTIONALLY LEFT BLANK
19 o DESIGN DATA 2" MIN. COMPLY WITH AASHTO LRFD BRIDGE DESIGN SPECIFICATIONS, 7TH EDITION, WITH 205 INTERIMS. DESIGN FORCE: MAX PLASTIC MOMENT = 9000 ft-lb GAUGE (0.25") THICKNESS MINIMUM MATERIAL DESIGN PROPERTIES: STRUCTURAL STEEL: Fy = p.s.i. STRUCTURAL STEEL MnDOT 3306 /8 / MINIMUM SOIL PROPERTIES: COARSE GRAINED SOIL: = 30 FINE GRAINED SOIL: C = 000 lb/sq.ft. DRIVEN SOCKET PER MANUFACTURER'S SPECIFICATIONS GALVANIZE ALL STEEL COMPONENTS AFTER FABRICATION PER MNDOT SPEC AND TRAFFIC PLAN VIEW 2 POST STOP METHOD PER MANUFACTURER. DEPTH AS PER MANUFACTURER'S SPECIFICATIONS BASED ON THE SOCKET DEPTH SET UP IN THE FHWA APPROVED CRASH TESTED HTCB SYSTEMS MEETING NCHRP 350 OR MASH REQUIREMENTS. 3 4 THREE (OPTIONAL) 7/8" DIAMETER VENT HOLES FOR GALVANIZING. UPPER HOLE MAY ALSO BE USED FOR POST STOP IF APPLICABLE. DRIVEN SOCKET DEPTH MUST MEET SPECIFIED DEPTH REGARDLESS OF SHALLOWER CRASH TESTED DEPTHS. LINE POST FOR CABLE BARRIER SYSTEM V:4H MAX. 3" TO 6" 3" TO 6" 2 '-2"MIN. (OPTIONAL) 7/8" VENT HOLES (TYP) 3 4 6'-0" 5'-0" MIN. 6-/2" 6-/2" 0-/2" DRIVEN SOCKET PER MANUFACTURER'S SPECIFICATIONS SOIL PLATE SOIL PLATE GAUGE (0.25") THICKNESS MINIMUM ELEVATION VIEW SIDE VIEW APPROVED AUGUST 9, 205 STATE DESIGN ENGINEER STATE OF MINNESOTA SPECIFICATION DEPARTMENT OF TRANSPORTATION REFERENCE HIGH-TENSION CABLE BARRIER 2554 LINE POST FOUNDATION REVISED STEEL DESIGN M.J.E. STANDARD PLATE NO. 8343A
20 THIS PAGE INTENTIONALLY LEFT BLANK
TYPE "A" CATCH BASIN
27" 1.67' TO BACK OF CURB LINE TOP OF GRATE ELEV. - SEE PLAN NEENAH CASTING R-3250-BV OR APPROVED EQUAL. "INFI SHIELD" SEAL OR APPROVED EQUAL RINGS (2 MIN., 1' MAX. OF RINGS AND MORTAR). PLASTER OUTSIDE,
More informationCATCH BASIN ST-1 ENGINEERING DEPARTMENT PLATE NUMBER 3.33' 3.0' 2.0' 4.33' 3.0' 4.0' 1.00' TO BACK OF CURB LINE
3.33' 3.0' 2.0' 4.33' 4.0' 3.0' 1.00' TO BACK OF CURB LINE TOP OF GRATE ELEV. - SEE PLAN NEENAH CASTING R-3067-V OR AS NOTED ON PLANS. "INFA-SHIELD" SEAL OR EQUAL. RINGS (2 MIN., 1' MAX. OF RINGS AND MORTAR).
More informationInlets & Catch Basins
A Delivering Reliability Inlets & Catch Basins Water-Conveyance & Drainage A Environmentally Responsible Oldcastle Precast to the Rescue All of our products are produced in a controlled environment helping
More informationAMENDMENTS TO OPSS 408 (OCT 89) CONSTRUCTION SPECIFICATION FOR ADJUSTING OR REBUILDING MANHOLES, CATCH BASINS, DITCH INLETS AND VALVE CHAMBERS
Works and Emergency Services CITY OF TORONTO WATER AND WASTEWATER SERVICES STANDARD CONSTRUCTION SPECIFICATIONS TS 408 November 2010 AMENDMENTS TO OPSS 408 (OCT 89) CONSTRUCTION SPECIFICATION FOR ADJUSTING
More information(SIZE) MANHOLES CATCH BASINS AND DITCH INLETS -Item No. ADJUSTING AND REBUILDING MANHOLES, CATCH BASINS AND DITCH INLETS - Item No.
(SIZE) MANHOLES CATCH BASINS AND DITCH INLETS -Item No. ADJUSTING AND REBUILDING MANHOLES, CATCH BASINS AND DITCH INLETS - Item No. Special Provision No. 407S06 July 2010 Aggregate Requirements, Lift Rings,
More informationThis drawing. is preliminary. and not for. construction or. implementation. purposes. project number 170 END VIEW DESIGN STRENGTHS: PLAN
project number 70 Reference Line 2-0" Reference 3 -" 6-0" 6-0" 3 -" Line Box Culvert Roadway Finished Channel -0" -0" E VIEW 20-0" Riprap 0-0" Riprap Outlet Invert El 87.0 Sta 233+00.00 Inlet Invert El
More informationSECTION STORM DRAINAGE
SECTION 02720 STORM DRAINAGE PART 1 - GENERAL 1.01 WORK INCLUDED A. Trenching and other excavation. B. Ground water control. C. Pipe bedding. D. Installation of storm drains and appurtenances. E. Installation
More informationCHAPTER 12: DRAINAGE
CHAPTER 12: DRAINAGE CHINOOK WINDS AND WINTER SNOWS A combination which frequently results in hazardous winter conditions on shaded portions of roadways under bridges. Icing conditions are a danger in
More informationCONSTRUCTION SPECIFICATION FOR THE INSTALLATION OF ELECTRICAL CHAMBER
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 602 MARCH 1993 CONSTRUCTION SPECIFICATION FOR THE INSTALLATION OF ELECTRICAL CHAMBER 602.01 SCOPE 602.02 REFERENCES 602.05 MATERIALS TABLE OF CONTENTS
More informationCITY OF SCHERTZ TEXAS ENGINEERING AND PUBLIC WORKS
TEXAS STANDARD CONSTRUCTION NOTES DRWN. BY: DSGN. BY: KJW 1 of 2 *Place geotextile fabric as a permeable seperator to prevent mixing of coarse aggregate and underlying soil. (as needed). 1. GEOTEXTILE
More informationFailure to acknowledge all addenda in the BID may cause rejection of the BID. See Instructions to Bidders.
Addendum #1 Project: Coteau Street & Utility Improvements Bid Date: 1:00 P.M., Local Time, March 20, 2017 Bid Location: Office of the City Administrator/Clerk, City of Lake Benton 106 S. Center Street
More informationSection 7 Roadway GENERAL REQUIREMENTS I. TYPICAL SECTION...7-1
Section 7 Roadway GENERAL REQUIREMENTS...7-1 I. TYPICAL SECTION...7-1 7.1 LANE WIDTHS...7-1 7.2 SHOULDER WIDTHS...7-1 7.3 CROSS SLOPE...7-2 7.4 CURB AND UNDERDRAINS...7-2 7.5 SIDEWALKS AND DRIVEWAYS...7-2
More informationCHAPTER 12: DRAINAGE
CHAPTER 12: DRAINAGE Inplace Drainage Structures On projects where inplace manholes or catch basins are likely to be either adjusted or reconstructed, the following additional information is necessary
More informationUNIFORM STANDARD DRAWINGS CLARK COUNTY AREA, NEVADA YEAR 2015 REVISIONS
, NEVADA YEAR 2015 REVISIONS SECTION TITLE AND REVISIONS SUMMARY EFFECTIVE DATE 217.S2 "Residential Curb and Gutter, R-Type" - New drawing to accommodate ADA requirements. 223 "Residential Driveway" -
More informationSUBJECT: Signal and Lighting Standard Plates , 8112, 8120, 8126, 8127, 8128, and 8134
MINNESOTA DEVELOPED BY: Design Standards ISSUED BY: Office of Project Management and Technical Support, Design Support Section TRANSMITTAL LETTER (5-0) MANUAL: Standard Plates DATED: July, 05 SUBJECT:
More informationThe Most Advanced Name in Water Management Solutions TM. The most cost-effective slotted and trench surface drain systems.
The Most Advanced Name in Water Management Solutions TM The most cost-effective slotted and trench surface drain systems. A sensible alternative to metal and concrete Since 1987, Duraslot surface drains
More informationITEM 555 CHAIN LINK FENCING
ITEM 555 AFTER MARCH 1, 2012 CHAIN LINK FENCING 555.1 Description. This item shall govern for furnishing the quantities of chain link fencing and gates as shown on the plans, including all posts, bracing
More information1. Division 01 Section General Requirements - Temporary Facilities and Controls. 2. Division 31 Section Earthwork.
PAGE 334000-1 SECTION 334000 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification sections,
More informationMANHOLES, VAULTS AND CATCH BASINS SECTION A. Section Soil and Aggregate Materials. C. Section Storm Drainage Systems
SECTION 02607-1 1.0 GENERAL 1.1 SCOPE: A. This section covers the work necessary for the construction of sanitary and storm system manholes, catch basins, and miscellaneous concrete structures complete.
More informationSUPPLEMENTAL DRAWINGS
CITY OF GREATER SUDBURY SUPPLEMENTAL DRAWINGS TO THE ONTARIO PROVINCIAL STANDARD DRAWINGS Rev: February 2012 CITY OF GREATER SUDBURY STANDARD DRAWINGS TABLE OF CONTENTS Greater Sudbury Standard Drawings
More informationPERMANENT PAVEMENT REPAIR NO SCALE
SAWCUT EXISTING PAVEMENT 2" BITUMINOUS CONCRETE SURFACE COURSE, CLASS 2 (MIN) CLEAN EDGE PRIOR TO PAVING AND PAINT WITH LIQUID BITUMEN. INSTALL SEALANT OVER JOINT UPON COMPLETION 2" BITUMINOUS CONCRETE
More informationFOR HISTORICAL REFERENCE ONLY
SILT FENCE TYPE TB PERIMETER CONTROL OF WATERWAY STEEL FENCE POST LESS THAN /3 ANCHOR TO LAND (TYP.) THE STREAM/RIVER WIDTH STREAM BANK CARRIER FLOAT LENGTH CURTAIN FABRIC STEEL TENSION CABLE WATER SURFACE
More informationNew Market Township. Driveway/Approach Permit
Permit Number Address: New Market Township Driveway/Approach Permit No person may construct or reconstruct any Driveway/Approach to a Township road without first obtaining a permit and the initial approval
More informationCOMMONWEALTH OF PENNSYLVANIA DEPARTMENT OF TRANSPORTATION BUREAU OF DESIGN
GENERAL NOTES DESIGN TABLE NOTES INDEX OF SHEETS 1. ALL DIMENSIONS ARE IN MILLIMETERS UNLESS OTHERWISE NOTED. U.S. CUSTOMARY UNITS IN ( ) PARENTHESIS.. ALL "DESIGN" METRIC UNITS INDICATED ARE SOFT CONVERTED
More informationSection 403. DRAINAGE STRUCTURES
403.01 Section 403. DRAINAGE STRUCTURES 403.01. Description. This work consists of adjusting, constructing, or temporarily lowering drainage structures and cleaning existing drainage structures and leads
More informationSECTION A-A NTS. Figure 4.1 Alternative Flow Dispersal Trench NOTES:
Figure 4.1 Alternative Flow Dispersal Trench NOTES: galvanized bolts 2" x 12" pressure treated grade board 2" x 2" notches 18" O.C. *20% max 12" min. 36" max 1' - 6" min *20% max 4" x 4" support post clean
More informationSECTION D2 MANHOLES AND CATCH BASINS GENERAL MATERIALS
SECTION D2 MANHOLES AND CATCH BASINS GENERAL This section covers the installation of new manholes, catch basins, drop inlets, drywall structures and the installation of hoods in existing catch basins.
More informationStorm Drainage
University of New Hampshire University of New Hampshire Scholars' Repository Division 33 Utilities Chapter 5 Technical Construction and Renovation Standards 4-23-2015 334100 - Storm Drainage Sandra Hickey
More informationAPPENDIX C INLETS. The application and types of storm drainage inlets are presented in detail in this Appendix.
Storm Drainage 13-C-1 APPENDIX C INLETS 1.0 Introduction The application and types of storm drainage inlets are presented in detail in this Appendix. 2.0 Inlet Locations Inlets are required at locations
More informationSECTION MANHOLES AND STRUCTURES. A. Section Includes: 1. Manholes for water, storm drain and sanitary sewer systems.
SECTION 33 05 13 MANHOLES AND STRUCTURES PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Manholes for water, storm drain and sanitary sewer systems. B. Related Sections: 1. Section 03 20 00 - Concrete
More informationDrainage structure refers to manholes, catch basins, leaching basins, inlets and drop inlets. Drainage structures are designated as follows.
403.01 Section 403. DRAINAGE STRUCTURES 403.01 Description. Adjust, construct, or temporarily lower drainage structures. Clean existing drainage structures and leads as directed by the Engineer. Drainage
More informationONE PIPE LENGTH MAX (REFER TO 1/4"/FT SLOPE (MIN) 5'-0" (MIN) OR 4" LATERAL NOTE #1) INCREASER RIGHT-OF-WAY/ 4"x6" REFER TO TYPICAL EXCAVATION,
VENT CAP (MUSHROOM TYPE) SOLID CAP EXIST GRADE MIN BUILDING REFER TO NOTE #4 MIN CONCRETE SIDEWALK CURB OR EDGE OF SIDEWALK STREET CLEANOUT (REFER TO NOTE #3) VENT PIPE 4" PVC 6" PVC CLEANOUT CONCRETE
More informationSPECIFICATIONS FOR STREET CONSTRUCTION WITHIN THE TOWN OF PLAINVILLE
SPECIFICATIONS FOR STREET CONSTRUCTION WITHIN THE TOWN OF PLAINVILLE BE IT ORDAINED by the Town Council of the Town of Plainville: SECTION 1. SUBDIVISIONS. All subdivisions hereinafter developed within
More informationThe Most Advanced Name in Water Management Solutions TM. The most cost-effective slotted and trench surface drain systems.
The Most Advanced Name in Water Management Solutions TM The most cost-effective slotted and trench surface drain systems. A sensible alternative to metal and concrete Since 1987, Duraslot surface drains
More informationThe Most Advanced Name in Water Management Solutions TM. The most cost-effective slotted and trench surface drain systems.
The Most Advanced Name in Water Management Solutions TM The most cost-effective slotted and trench surface drain systems. A sensible alternative to metal and concrete Since 1987, Duraslot surface drains
More informationTesting. Test drainage products according to the applicable AASHTO or ASTM specification, except as otherwise noted.
909.01 Section 909. DRAINAGE PRODUCTS 909.01 General Requirements. If only the size and class are specified for a culvert or sewer, use the pipe materials as shown in Table 401-1 and 402-1 respectively.
More informationNORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017
SECTION 33 3400 STORM UTILITY DRAINAGE PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationONTARIO PROVINCIAL STANDARD SPECIFICATION
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 1850 NOVEMBER 2003 MATERIAL SPECIFICATION FOR FRAMES, GRATES, COVERS, AND GRATINGS TABLE OF CONTENTS 1850.01 SCOPE 1850.02 REFERENCES 1850.03 DEFINITIONS
More informationDelivering Reliability. Electrical Vaults. Power & Energy-Underground Structures
A Delivering Reliability Electrical Vaults Power & Energy-Underground Structures A The Benefits of Precast Vaults Electrical vaults house power cables and transformers, and are a preferred alternative
More informationSection 401. PIPE CULVERTS
401.02 Section 401. PIPE CULVERTS 401.01. Description. This work consists of constructing pipe culverts of the size and class required, including excavation and backfill. 401.02. Materials. Provide materials
More informationCHAPTER 11: WALLS.
CHAPTER 11: WALLS MODULAR BLOCK WALL (DRY CAST) Rather than being pre-approved as systems, the components of Modular block walls (dry cast) are pre-approved separately. The approved MBW components are
More informationBaseline Document Change Announcement
BDC16D-01 Page 1 of 7 New Jersey Department of Transportation 1035 Parkway Avenue, PO Box 600, Trenton, New Jersey 08625-0600 Baseline Document Change Announcement ANNOUNCEMENT: BDC16D-01 DATE: September
More informationSANITARY MANHOLE S-1 ENGINEERING DEPARTMENT PLATE NUMBER NEENAH R-1733 CASTING ASSEMBLY OR AS NOTED ON PLAN OR APPROVED EQUAL.
"INFI-SHIELD" SEAL OR EQUAL. NEENAH R-1733 CASTING ASSEMBLY OR AS NOTED ON PLAN OR APPROVED EQUAL. 27" HDPE ADJUSTING RINGS (2 MIN., 1' MAX. OF RINGS). ECCENTRIC CONE 4.0' HIGH 48" 5" P2 PROFILE GASKET
More informationThis type of masonry shall consist of brick laid in full beds of cement mortar.
SECTION 11.0 DRAINAGE STRUCTURES 11.01 Scope of Work This item shall consist of installation and construction of storm drainage pipes, culverts, basins, headwalls, manholes, junction boxes, head ditches,
More informationSECTION 39 - MANHOLES TABLE OF CONTENTS 39-1 GENERAL PRECAST CONCRETE MANHOLES
Section SECTION 39 - MANHOLES TABLE OF CONTENTS 39-1 GENERAL... 39-1 39-2 PRECAST CONCRETE MANHOLES... 39-1 39-2.01 Precast Concrete Storm Drain Manholes... 39-1 39-3 SADDLE MANHOLES... 39-2 39-3.01 Saddle
More informationFEBRUARY 2019 LRFD BRIDGE DESIGN 5-1
FEBRUARY 2019 LRFD BRIDGE DESIGN 5-1 5. CONCRETE STRUCTURES Reinforced and prestressed concrete are used extensively in bridge projects. In addition to general design guidance and information on detailing
More informationSECTION 39 - MANHOLES TABLE OF CONTENTS
Section SECTION 39 - MANHOLES TABLE OF CONTENTS Page 39-1 GENERAL... 39.1 39-2 CONCRETE MANHOLES... 39.1 39-2.01 NOT USED... 39.1 39-2.02 Concrete Storm Drain Manholes... 39.1 39-3 SADDLE SEWER MANHOLES...
More informationSTANDARD CONSTRUCTION DETAILS SANITARY SEWER REVISED MARCH 2018 DEPARTMENT OF ENGINEERING
STANDARD CONSTRUCTION DETAILS REVISED MARCH 2018 GENERAL NOTES EMBEDMENT DETAILS EMBEDMENT DETAILS TWO-WAY CLEANOUT - EXISTING LATERAL TWO-WAY CLEANOUT - NEW CONSTRUCTION TYPICAL SEWER HOUSE SERVICE CONNECTION
More informationFOR CRITICAL AREAS ADJACENT TO WETLANDS OR BELOW LONG AND/OR STEEP SLOPES, STEEL POSTS ARE NECESSARY AS INDICATED ON THE PLANS.
WOOD OR STEEL FENCE POST (T-POST), MINIMUM 5' LONG, 6' MAXIMUM SPACING. STEEL POSTS: POST NOTCHES TO FACE AWAY FROM FABRIC. WOOD POSTS: ATTACH FABRIC TO POSTS WITH WOOD LATH A MINIMUM 1/4" THICK x 9" LONG
More information16. Design of Pipeline Structures.
16. Design of Pipeline Structures. a. General. 1) The following guidelines are for the design of structures for water and sewer pipelines including structural concrete and miscellaneous metals design.
More informationCONSTRUCTION SPECIFICATION FOR INSTALLATION OF ELECTRICAL CHAMBERS
ONTARIO PROVINCIAL STANDARD SPECIFICATION OPSS.PROV 602 NOVEMBER 2017 CONSTRUCTION SPECIFICATION FOR INSTALLATION OF ELECTRICAL CHAMBERS TABLE OF CONTENTS 602.01 SCOPE 602.02 REFERENCES 602.03 DEFINITIONS
More informationMagnumStone Specifications Gravity
MagnumStone Specifications Gravity SPECIFICATION FOR MAGNUMSTONE GRAVITY MECHANICALLY STABILIZED EARTH SYSTEM PART 1: GENERAL.01Description The work consists of supplying and installing all aspects of
More informationMATERIAL SPECIFICATION FOR FRAMES, GRATES, COVERS, AND GRATINGS
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 1850 NOVEMBER 2007 MATERIAL SPECIFICATION FOR FRAMES, GRATES, COVERS, AND GRATINGS TABLE OF CONTENTS 1850.01 SCOPE 1850.02 REFERENCES 1850.03 DEFINITIONS
More informationSECTION STORM SEWER PIPE
SECTION 4200 - STORM SEWER PIPE 4200.1 SCOPE: This section covers the requirements for all labor, equipment and materials for the installation of storm sewers pipes. Trenching guidelines are provided in
More informationElectric Service Standards
V: 1 of 6 A. Padmounted Requirements Complete requirements are contained in FPL specifications given to Customers for individual projects. Typical pad mounted transformer requirements include, but are
More informationPIPE CULVERTS. Construct pipe culverts, beveled ends, pipe aprons, and associated appurtenances.
PIPE CULVERTS PART 1 - GENERAL 1.01 SECTION INCLUDES A. Pipe Culverts B. Pipe Aprons and Beveled Ends C. Footings for Concrete Pipe Aprons D. Pipe Apron Guards 1.02 DESCRIPTION OF WORK Construct pipe culverts,
More informationNOTE: 1) PRIOR TO BEGINNING WORK TRANSFER RIM ELEV. FROM MH K1 TO A TEMPORARY BENCH MARK FOR USE AS CONTROL DURING CONSTRUCTION. 2) CONTRACTOR TO INST
NOTE: 1) PRIOR TO BEGINNING WORK TRANSFER RIM ELEV. FROM MH K1 TO A TEMPORARY BENCH MARK FOR USE AS CONTROL DURING CONSTRUCTION. 2) CONTRACTOR TO INSTALL MANHOLE LIDS FLUSH WITH EXISTING GROUND SURFACE.
More informationAppendix J: Storm Conveyance Design Parameters
Appendix J: Storm Conveyance Design Parameters Drain Commissioner 39 February 2005 STORM DRAINAGE DESIGN CRITERIA A. STORM SEWERS 1. The required discharge capacity shall be determined by the Rational
More informationSECTION CURB, COMBINATION CURB AND GUTTER, AND MONOLITHIC MEDIAN. 1. Bituminous concrete pavement; Section
02670-1 of 6 SECTION 02670 CURB, COMBINATION CURB AND GUTTER, AND 02670.01 GENERAL A. Description This work shall include, but not necessarily be limited to, the construction of concrete curb, concrete
More informationThe work required for this project includes, but is not limited to, the following items, not listed in order of execution.
ESTIMATE OF QUANTITIES SPECIFICATIONS Construction Specifications: South Dakota Standard Specifications for Roads and Bridges, 2004 Edition and Required Provisions, Supplemental Specifications and/or Special
More informationSECTION 920 SANITARY AND STORM SEWER MANHOLES
SECTION 920 SANITARY AND STORM SEWER MANHOLES 920.1 GENERAL This section contains items which are relative to the installation of sanitary and storm sewer manholes. 920.2 REFERENCES 920.2.1 ASTM C 43 C
More informationSection Storm Sewers STORM SEWERS PART 1 - GENERAL 1.01 SECTION INCLUDES. A. Storm Sewers. B. Abandonment of Storm Sewers
STORM SEWERS PART 1 - GENERAL 1.01 SECTION INCLUDES A. Storm Sewers B. Abandonment of Storm Sewers 1.02 DESCRIPTION OF WORK A. Construct storm sewers. B. Abandon storm sewers. 1.03 SUBMITTALS Comply with
More informationNew Fulton State Hospital Energy Control Center and Services Building (ECC/SVC) Project Number: M
SECTION 334100 - STORM UTILITY DRAINAGE PIPING PART 1 -GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationTRENCH SYSTEM Pedestrian channels are rated for 200 lbs./ft 2 Pedestrian channels are rated for 200 lbs./ft 2 8012 (10X10) 12" 10" 10" 10" 8022 (20X20) 12" 20" 20" 20" 8026 (24X24) 12" 24" 24" 24"
More informationOHIO DEPARTMENT OF TRANSPORTATION CENTRAL OFFICE, 1980 W. BROAD ST., COLUMBUS, OHIO
OHIO DEPARTMENT OF TRANSPORTATION CENTRAL OFFICE, 1980 W. BROAD ST., COLUMBUS, OHIO 43216-0899 July 20, 2018 To: Users of the Bridge Design Manual From: Tim Keller, Administrator, Office of Structural
More informationMATERIAL SPECIFICATION FOR FRAMES, GRATES, COVERS, AND GRATINGS
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 1850 APRIL 2013 MATERIAL SPECIFICATION FOR FRAMES, GRATES, COVERS, AND GRATINGS TABLE OF CONTENTS 1850.01 SCOPE 1850.02 REFERENCES 1850.03 DEFINITIONS
More informationPASSAIC COUNTY TECHNICAL INSTITUTE CCA 1422 NEW S.T.E.M. BUILDING 2017
SECTION 02630 - STORM DRAINAGE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationCONSTRUCTION SPECIFICATION FOR ADJUSTING OR REBUILDING MAINTENANCE HOLES, CATCH BASINS, DITCH INLETS, AND VALVE CHAMBERS
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 408 NOVEMBER 2015 CONSTRUCTION SPECIFICATION FOR ADJUSTING OR REBUILDING MAINTENANCE HOLES, CATCH BASINS, DITCH INLETS, AND VALVE CHAMBERS TABLE OF
More informationB. Fiberglass for construction in back lot easements placed on cast-in-place base.
Section 02083 PART 1 G E N E R A L 1.01 SECTION INCLUDES A. Fiberglass manholes for unpaved areas placed on top of a precast base to form a manhole. B. Fiberglass for construction in back lot easements
More informationCITY OF WARRENVILLE STANDARD SPECIFICATIONS WATER MAIN, SANITARY SEWER AND STORM SEWER
CITY OF WARRENVILLE STANDARD SPECIFICATIONS WATER MAIN, SANITARY SEWER AND STORM SEWER WATER MAIN 1. All open cut water main shall be polyvinyl chloride plastic (PVC) pressure pipe per AWWA specification
More informationMiscellaneous and Cast Iron Listings
aeconcrete.com May 2017 Miscellaneous and Cast Iron Listings Drawing Number Item Description Product Size (Length X Width X Depth in mm) SVVZ-20-SUMP-C Drainage Sump w/ Cover 660 x 510 x 765 i.d. SVVZ-NC-SUMP-C
More informationCounty of Sacramento Standard Construction Specifications January 1, 2008 TECHNICAL PROVISIONS
County of Sacramento Standard Construction Specifications January 1, 2008 TECHNICAL PROVISIONS SECTION 27 CURBS, GUTTERS, SIDEWALKS, AND DRAINAGE STRUCTURES 27-1 GENERAL Concrete curbs, gutters, sidewalks,
More informationMICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR LOW-TENSION CABLE BARRIER. OPR:CT 1 of 5 APPR:JAR:DBP: FHWA:APPR:
MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR LOW-TENSION CABLE BARRIER OPR:CT 1 of 5 APPR:JAR:DBP:09-07-11 FHWA:APPR:09-07-11 a. Description. This work consists of furnishing and installing
More informationGENERAL NOTES ROADWAY CONSTRUCTION RD0001-1A ISSUED:2017 REVISED: --
ROADWAY CONSTRUCTION NOTES 1. ALL RIGHT-OF-WAY OTHER THAN ROADWAY AREAS SHALL BE SODDED. ALL SLOPE STEEPER THAN 6:1 SHALL REQUIRE SODDING. THE CITY RESERVES THE RIGHT TO REQUIRE SODDING IN SPECIAL AREAS
More information1 Revised: 2019 Edition
STORM SEWERS PART 1 - GENERAL 1.01 SECTION INCLUDES A. Storm Sewers B. Abandonment of Storm Sewers 1.02 DESCRIPTION OF WORK A. Construct storm sewers. B. Abandon storm sewers. 1.03 SUBMITTALS Comply with
More informationSpecial Provision for LRFD Pipe Culvert Burial Tables
All Regional Engineers Omer M. Osman, P.E. Special Provision for LRFD Pipe Culvert Burial Tables January 9, 2015 This special provision was developed by the Bureau of Bridges and Structures as a result
More informationCONSTRUCTION SPECIFICATION FOR INSTALLATION OF ELECTRICAL CHAMBERS
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 602 NOVEMBER 2008 CONSTRUCTION SPECIFICATION FOR INSTALLATION OF ELECTRICAL CHAMBERS TABLE OF CONTENTS 602.01 SCOPE 602.02 REFERENCES 602.03 DEFINITIONS
More informationSECTION PRECAST CONCRETE MANHOLES
SECTION 02601 PRECAST CONCRETE MANHOLES PART 1 GENERAL 1.1 The work specified in this section shall include the furnishing, hauling, and placing of all precast manholes shown on the drawings and as specified
More informationFLORIDA DEPARTMENT OF TRANSPORTATION
TEMPORARY WIREWALL MSE RETAINING WALLS SAMPLE DETAIL DRAWINGS INDEX DESCRIPTION 1 TITLE 2 GENERAL NOTES 3-4 TEMPORARY WIREWALL DETAILS 5-6 TRI-WEB TEMPORARY WALL DETAILS 7 TYPICAL TEMPORARY WIREWALL 8
More informationMATERIAL SPECIFICATION FOR FRAMES, GRATES, COVERS, AND GRATINGS
ONTARIO PROVINCIAL STANDARD SPECIFICATION OPSS.MUNI 1850 NOVEMBER 2018 MATERIAL SPECIFICATION FOR FRAMES, GRATES, COVERS, AND GRATINGS TABLE OF CONTENTS 1850.01 SCOPE 1850.02 REFERENCES 1850.03 DEFINITIONS
More informationCLEARING & GRADING GENERAL NOTES CITY OF SCHERTZ TEXAS ENGINEERING AND PUBLIC WORKS SHEETNUMBER BCP PROJECT NO.: DATE: 11/1/18
L:\Engineer\Standard Details and Technical Specifications\Standard Details\201\DRAINAGE & ENV\DRAINAGE AND ENVIRONMENTAL DETAILS 11.01.201.dwg I N COR P ORA T E D TEXAS DRWN. BY: CLEARING & GRADING GENERAL
More informationSpecial Specification 6186 Intelligent Transportation System (ITS) Ground Box
Special Specification Intelligent Transportation System (ITS) Ground Box 1. DESCRIPTION 2. MATERIALS Construct, furnish, install or remove Intelligent Transportation System (ITS) ground boxes for fiber
More informationPrecast Concrete Trench Drain Systems INSTALLATION INSTRUCTIONS
Precast Concrete Trench Drain Systems INSTALLATION INSTRUCTIONS GENERAL INSTALLATION INSTRUCTIONS 1 Ensure that the trench where the channels are going to be installed has enough room for the appropriate
More informationD-1 THE CITY OF HARRISBURG 1 1/2" MIN. ID-2 WEARING COARSE EXISTING STREET SURFACE AC-20 SEALER (ALL AROUND) 1 1/2" MIN. ID-2 BINDER COARSE
EXISTING STREET SURFACE 1 1/2" MIN. ID-2 BINDER COARSE 1 1/2" MIN. ID-2 WEARING COARSE AC-20 SEALER (ALL AROUND) 8" CLASS A P.C. CONCRETE SAW CUT TOP OF CONCRETE SHALL MEET SURFACE OF EXISTING CONCRETE.
More informationPerma-Column Deck Post Design Manual
Perma-Column Deck Post Design Manual DP4430, DP4440, DP4640, DP6630, DP6640, DP6430, and DP6440 models Project Number S007-12 by Brent Leatherman, P.E. Timber Tech Engineering, Inc E-Mail: bl@timbertecheng.com
More informationDepartment of Building and Zoning Approaches and Sidewalks for ONE AND TWO FAMILY CONSTRUCTION
Department of Building and Zoning Approaches and Sidewalks for ONE AND TWO FAMILY CONSTRUCTION GENERAL ITEMS SUBGRADE Prior to pouring concrete all subgrades must be wetted and compacted. All formwork
More informationSPECIFICATIONS - DETAILED PROVISIONS Section Stainless Steel Sluice Gates C O N T E N T S
SPECIFICATIONS - DETAILED PROVISIONS Section 11294 - Stainless Steel Sluice Gates C O N T E N T S PART 1 - GENERAL... 1 1.01 SUMMARY... 1 1.02 REFERENCES... 1 1.03 DEFINITIONS... 1 1.04 DESIGN REQUIREMENTS...
More informationStandard products Tasmania 2010
Standard products Tasmania 2010 Standard products A catalogue of standard products manufactured at Humes Invermay. All products are cast with means of lifting unless otherwise specified. Other products
More informationHighway Drainage 1- Storm Frequency and Runoff 1.1- Runoff Determination
Highway Drainage Proper drainage is a very important consideration in design of a highway. Inadequate drainage facilities can lead to premature deterioration of the highway and the development of adverse
More informationSECTION UTILITY POLYETHYLENE CONTAINMENT PIPE SYSTEMS
SECTION 02670 UTILITY POLYETHYLENE CONTAINMENT PIPE SYSTEMS PART 1 - GENERAL 1.01 WORK INCLUDED A. Trenching and other excavation. B. Ground water control. C. Pipe bedding. D. Installation of containment
More information35-46 KA KA
35-46 KA 4586-01 7-46 KA 4583-01 HOST PROJECT 6 KA 4590-01 Page 1 of 48 HOST PROJECT 6 KA 4590-01 70-5 KA 4588-01 5-5 KA 4584-01 Page of 48 6 KA 4590-01 Page 3 of 48 70-5 KA 4588-01 At the Contractor's
More informationTECHNICAL SPECIFICATION
TECHNICAL SPECIFICATION ITEM 02514 MANHOLES 1.0 GENERAL 1.1 SCOPE This section provides for construction of sewer manholes complete in place, including the furnishing and adjusting to grade of an existing
More informationQualified Product Policy 15 Drainage Structure Miscellaneous Components Qualified Product List 14 [G] Heavy Duty Gray Cast Iron
SCDOT Qualified Product Policy 15 1 SOUTH CAROLINA DEPARTMENT OF TRANSPORTATION Drainage Structure Miscellaneous Components (See also QPL14 for precast drainage structure components) This policy covers
More informationSECTION STORM DRAINAGE SYSTEM Excavating, Backfilling, and Compaction for Utilities Cast-in-place Concrete.
SECTION 02720 STORM DRAINAGE SYSTEM PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 02221 - Excavating, Backfilling, and Compaction for Utilities. 2. 03300 - Cast-in-place Concrete. 1.02 REFERENCES
More informationMATERIAL SPECIFICATION FOR FRAMES, GRATES, COVERS, AND GRATINGS
ONTARIO PROVINCIAL STANDARD SPECIFICATION OPSS 1850 APRIL 2018 (Formerly OPSS 1850, April 2013) Note: The MUNI implemented in April 2018 replaces OPSS 1850 COMMON, April 2013 with no technical content
More informationJANUARY 25, 2016 ADDENDUM NO. 3 FOR. ORD Baggage Service Road Retaining Wall Repair
JANUARY 25, 2016 ADDENDUM NO. 3 FOR ORD Baggage Service Road Retaining Wall Repair Specifications and Contract Documents Number: 132110 CDA Project Number: H6163.15-02 For which bids are scheduled to be
More informationMATERIAL SPECIFICATION FOR STEEL POLES, BASE MOUNTED
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS.MUNI 2423 APRIL 2017 MATERIAL SPECIFICATION FOR STEEL POLES, BASE MOUNTED TABLE OF CONTENTS 2423.01 SCOPE 2423.02 REFERENCES 2423.03 DEFINITIONS -
More informationCHAPTER 3: DETAILS and ADA
CHAPTER 3: DETAILS and ADA ADA PLAN REVIEW CHECKLISTS When there is ADA work in a project the ADA Plan Review Checklists NEED to be filled out and submitted. The ADA Plan Review Checklist #1 Shall be submitted
More informationCivil and Structural Engineering CONSTRUCTION OF BRIDGE STRUCTURES SHALL BE IN ACCORDANCE WITH THE FOLLOWING SPECIFICATIONS, LISTED IN ORDER OF PRECEDENCE: 1. CDOT STANDARD SPECIFICATIONS FOR ROAD AND
More information1:100 GABION WALLS LEGEND NOT FOR CONSTRUCTION TYPICAL DRAWING TEXT SETTING TYPE CHARACTER HEIGHT PEN SETUP FOR PLOTTING SUBTITLE
LEGEND SHEET 0 BATTERED WALLS - TYPICAL SECTIONS AND CONSTRUCTION S VERTICAL WALLS - TYPICAL SECTIONS AND CONSTRUCTION S AND CONSTRUCTION S SHEET 02 SHEET 0 SHEET 04 RETAINING STRUCTURES WITH CUT OFF WALLS
More information