SECTION EPOXY FLOORING SYSTEMS
|
|
- Lynette Cannon
- 6 years ago
- Views:
Transcription
1 SECTION EPOXY FLOORING SYSTEMS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section Includes: 1. Medium Texture Fluid Applied Seamless Epoxy Resin Flooring, Key Mortar SLT 1/8 thickness. 2. Light Texture Fluid Applied High Build Epoxy Coating mil DFT Resin Flooring. 3. Smooth, Pigmented Epoxy Floor Coating System mils DFT Resin Flooring. 4. Clear Epoxy Floor Coating System. 5. Accessories necessary for complete installation for all systems. B. Related Sections: 1. Cast-in-Place Concrete: Section a. Concrete sub-floor to be level and to have a steel troweled finish. All concrete slabs shall be either wet cured or cured through the use of moisture-retaining covers. No curing agents or other additives which could prevent bonding shall be used. 2. Decorative Concrete Polished Flooring: Section a. Surface preparation for Epoxy Stripe Coating system. 1.3 REFERENCE STANDARDS A. American Society for Testing and Materials (ASTM) Publications: 1. C-307 Test Method for Tensile Strength of Chemical-Resistant Mortars. 2. C-501 Test Method for Relative Resistance to Wear Unglazed Ceramic Tile by the Taber Abrader. EPOXY FLOOR SYSTEMS
2 3. C-531 Test Method for Linear Shrinkage and Coefficient of Thermal Expansion of Chemical-Resistant Mortars, Grouts, and Monolithic Surfacing. 4. C-579 Test Methods for Compressive Strength of Chemical- Resistant Mortars and Monolithic Surfaces. 5. C-580 Test Method for Flexural Strength and Modulus of Elasticity of Chemical-Resistant Mortars, Grouts, and Monolithic Surfacing. 6. C-884 Test Method for Thermal Compatibility Between Concrete and an Epoxy Resin Overlay. 7. D-570 Water Absorption of Plastics. 8. D-695 Compression Properties of Rigid Plastic. 9. D-1308 Test Method for Effect of Chemicals on Clear and Pigmented Organic Finishes. B. Military Specifications (Mil. Spec.) 1. MIL D F (Impact Resistance) Section MIL D F (Indentation Resistance) Section MIL D-3234 F (Resistance to Elevated Temperature) Section C. ACI 301 Specifications for Structural Concrete for Buildings (most recent edition). Committee in Concrete 403 bulletin 59-43, Bond Strength to Concrete. 1.4 SUBMITTALS A. Samples: Submit two 12 inch by 12 inch cured samples of each floor color indicating color combination and non-skid properties. Approved samples will be used during installation for product match. B. Manufacturers Application Instructions: Submit descriptive data and specific recommendations for mixing, application, curing including any precautions of special handling instructions required to comply with the Occupational Safety and Health Act. C. Shop Drawings: Shop Drawings shall be furnished showing installation of cove base and termination details, and details at floor material transitions and where adjoining equipment. Locate and provide detailing for flexible joints required for flooring in area of installation. D. Maintenance Instructions: Submit current copies of the flooring manufacturer's printed recommendations on maintenance methods and products. Submit in accordance with Section Closeout Procedures. 1.5 QUALITY ASSURANCE EPOXY FLOOR SYSTEMS
3 A. Materials used in the floor surfacing shall be the products of a single manufacturer. B. Installation shall be performed by an applicator with minimum 3 years experience in work of similar nature and scope. Installer must be approved by the manufacturer of the floor surfacing materials. The contractor shall furnish a written statement from the manufacturer that the installer is acceptable. C. Installer to verify locations of all flexible joints required by the provisions of this Section and by the recommendations of the related material manufacturers. 1. Joint locations may or may not be shown in drawings. D. Installer to keep daily log of the date of installation, room number, type, color, and method of application of product being installed. Log must be available for inspection by the owners representative and the Architect upon request. E. Contractor to have proven experience with specified system. F. Mock-up: Prior to starting application of flooring, provide full-scale mock-up to establish acceptable quality, durability, and appearance. Mock-up area must not be less than 50 square feet. 1. Acceptable mock-up to be standard of quality for remaining work. 2. Accepted work may remain in place. Unacceptable work to be removed and replaced until acceptable. 1.6 PROJECT CONDITIONS A. Maintain the ambient room and the floor temperatures at 50 degrees Fahrenheit, or above, for a period extending from 72 hours before, during and after floor installation. Concrete to receive surfacing shall have cured for at least 28 days and shall have been free of water for at least 7 days. B. Advise other trades of fixtures and fittings not to be installed until flooring is cured and protected. 1.7 PROTECTION A. Protect adjacent surfaces not scheduled to receive the flooring by masking, or by other means, to maintain these surfaces free of the flooring material. B. Provide adequate ventilation and fire protection at all mixing and placing operations. Prohibit smoking or use of spark or flame producing devices within 50 feet of any mixing or placing operation. C. Provide polyethylene or rubber gloves or protective creams for all workmen engaged in applying products containing epoxy. 1.8 PRODUCT DELIVERY, STORAGE, AND HANDLING EPOXY FLOOR SYSTEMS
4 A. All materials shall be delivered to project site in original manufacturer's sealed containers including type of material, batch numbers, date of manufacture, and pertinent labels intact and legible. B. Store materials in dry protected area at a temperature between 50 F to 80 F. C. Follow all manufacturer's specific instructions and prudent safety practices for storage and handling. PART 2 - PRODUCTS 2.1 MANUFACTURERS A. Key Resin Company. Contact: Fred Ramsey (757) , (804) CERTIFIED INSTALLER/APPLICATOR A. The applicators for this product is proprietary. No other installers will be allowed. 1. FlorLine Inc. Shane Reynolds (330) QuestMark, division of CentiMark. Ron Pritt (717) , (484) , or ron.pritt@centimark.com. 2.3 MATERIALS A. Medium Texture Fluid Applied Seamless Epoxy Resin Flooring shall be Key Mortar SLT 1/8 Textured Self Leveling Flooring System, sealed with Chemical and Stain Resistant Polyurethane Sealer, Key #470 Polyaspartic Topcoat. 1. Prime Coat: Two component penetrating damp-proof epoxy: Key #502 Primer/Low Modulus Binder. 2. Aggregates: a. Blended self-leveling slurry filler: Key Self-Leveling Filler. b. Key CEC 1000 Broadcast Aggregate. 3. Matrix: Matrix-epoxy/aggregate composition using 100% solids epoxy binder: Key #511 Epoxy Binder (pigmented). 4. High solids seal coat: a. Colored two component, 100% solids epoxy: Key # % Solids Epoxy Coating b. Colored two component, chemically cured polyaspartic: Key #470 Polyaspartic Topcoat. 5. Flexible epoxy joint filler: Key #780 Joint Filler to match color of floor topping. EPOXY FLOOR SYSTEMS
5 6. Elastomeric, crack-bridging membrane: Key #580 Flexible Epoxy B. Light Texture Fluid Applied High Build Epoxy Coating Resin Flooring mils DFT. 1. Severe and Moderate Environments (Gloss Finish): One finish coat over a primer coat of epoxy with a broadcast aggregate for non-slip surface and grout coat of pigmented epoxy. a. Primer: Two-part 100 % Solids Epoxy Primer. Primer coat to be applied over properly prepared concrete substrate at 10.0 mils WFT. While material is wet broadcast 30 mesh washed silica sand at approximately 20 lb. per 100 sq. ft. (to excess). 1) Key Resin Company: Key Resin # 502 Primer/Low Modulus Binder Clear. 2) Key Resin Company: Key Resin 30 Mesh Broadcast Aggregate. b. Intermediate Coat: Two-part 100% Solids Epoxy Binder. Key Resin Company: Key # 520 Epoxy Coating Carmax Gray. After primer has cured sweep excess aggregate from floor and apply intermediate coat at 10 mils WFT to lock in aggregate. c. Finish Coats: Two-part 100% Solids Epoxy Binder. Key Resin Company: Key Resin # 520 Epoxy Coating Carmax Gray. Apply finish coat at 10 mils WFT. C. Epoxy Stripe Coating 1. Stripes located at Decorative Concrete Polished Flooring in Service and FQC as indicated on drawings. a. Primer: Key Resin # 502 Epoxy Primer (pigmented white will help top coat cover better but not 200 sq. ft. per gallon (8 mils DFT). b. Finish Coat: Key Resin # 470 Polyaspartic Carmax 160 sq. ft. per gallon (10 mils DFT). D. Smooth, Pigmented Epoxy Floor Coating System mils DFT 1. Severe and Moderate Environment (Gloss Finish): One coat over a primer coat. a. Primer: Two-part 100% Solids Epoxy Primer. Primer coat to be applied over properly prepared concrete substrate at 8.0 to 10.0 mils WFT. While material is wet broadcast 30 mesh washed silica sand at approximately 20 lb. per 100 sq. ft. (to excess). 1) Key Resin Company: Key Resin # 502 Primer/Low Modulus Binder Clear. b. Finish Coat: Two-part 100% Solids Epoxy Coating (Carmax Gray) applied at 8.0 to 10.0 mils WFT. EPOXY FLOOR SYSTEMS
6 1) Key Resin Company: Key Resin # 520 Epoxy Coating Carmax Gray at 8.0 to 10.0 mils WFT. E. Clear Epoxy Floor Coating System 1. Paint Booth Flooring (Gloss Finish): One coat over a primer coat. a. Primer: Two-part 100% Solids Epoxy Primer. Primer coat to be applied over properly prepared concrete substrate at 5.0 to 8.0 mils. WFT. 1) Key Resin Company: Key Resin # 502 Primer/Low Modulus Binder Clear. b. Finish Coat: Two-part 100% Solids Epoxy Coating Clear applied at 5.0 to 8.0 mils WFT. 1) Key Resin Company: Key Resin # 502 Primer/low Modulus Binder Clear. 2.4 FINISHES Color and texture as indicated on drawings. PART 3 - EXECUTION 3.1 PREPARATION A. Obtain Architect's approval of mock-up before installing flooring. B. Prior to installation of structural floor slab, advise General Contractor, in writing, of all requirements of concrete substrate regarding finish, level tolerance, and curing. C. Locate all flexible joints required. D. Preparation of Surface: 1. After concrete curing period (28 days minimum) has elapsed, inspect surfaces to receive flooring and verify that condition is smooth and free from conditions that will adversely affect execution, permanence, or quality of work. Remove all projections, all debris detrimental to flooring system, and dirt, oil contaminates, grease, and surface coatings affecting bond. 2. Notify Architect in writing prior to commencing work of any conditions deemed unsatisfactory for the installation; installation of flooring materials is understood as acceptance of the substrate as satisfactory. EPOXY FLOOR SYSTEMS
7 3. Verify that moisture content is within range acceptable to flooring material manufacturer using calcium chloride test per ASTM F1869 and/or relative humidity probe test per ASTM F Prepare surface as required by manufacturer's printed instructions. Preferred surface preparation is steel shot blasting or similar mechanical method. 5. Air Drying: After completion of cleaning, allow concrete surface to air dry thoroughly prior to application of the floor surfacing. Blowers or oil free compressed air may be used. Do not use flame-drying methods. Prior to application of surfacing, the concrete surface shall be tested for excessive moisture vapor transmission in at least two locations. Place rubber mats at each location with smooth side against concrete. Polyethylene with all edges taped may be used in lieu of mats. After hours, remove mat or sheeting and examine the floor surface for moisture accumulation. If tests indicate an accumulation of moisture at either location, additional air-drying shall be undertaken until such time as additional tests show no moisture accumulation. 6. Treat cracks in concrete using manufacturer's recommended practice. Rout out crack and joints, and fill with semi-flexible epoxy; coat with flexible membrane in accordance with manufacturer's recommendation to prevent cracking through flooring system. 7. Remove plastic void cap at the top of the expansion joint material placed at the perimeter of the concrete slabs. Clean joint of all foreign material. 8. Verify that surface preparation for Epoxy Stripe Coating meets manufacturers requirements. 3.2 INSTALLATION A. Install all floor materials in strict conformance with manufacturer's instructions. B. Install a screed line or termination strip at all color transitions except at stripes where a masked edge topcoat of a different color shall be installed. C. Elastomeric membrane, if required, at concrete slab applications and where indicated. Install in single or multiple coats to a minimum dry film thickness of 25 mils. D. Once self-leveling broadcast epoxy materials have cured remove excess broadcast sand from floor surface. E. Match finished work to approved samples, uniform in thickness, sheen, color, patterns and texture, and free from defects detrimental to appearance. F. Install flexible joint filler at all perimeter expansion joints where concrete slab abuts vertical wall assembly. Color of filler to match floor system. G. Install flexible epoxy joint sealant in all saw cut and cold joints. H. Apply temporary protection until floor is fully cured. EPOXY FLOOR SYSTEMS
8 3.3 INSPECTION A. Touch up and repair all work that is not acceptable to Architect and request final acceptance. 3.4 CLEANING AND PROTECTION A. Remove coating spatters from glass, plumbing fixtures, and adjoining surfaces. B. Repair any damage to coating or surfaces caused by cleaning operation start. C. Remove debris from job site and leave storage area clean. D. At Presentation Lanes protect finished surfaces from damage for remainder of construction period until project is turned over to Owner. END OF SECTION EPOXY FLOOR SYSTEMS
May 8, 2017 ADDENDUM #1. IFB Resin Floor System For Highway Department Central District Building
May 8, 2017 ADDENDUM #1 IFB 17-082 Resin Floor System For Highway Department Central District Building Addendum #1 is being issued to offer an alternate resin flooring system. 096700 FLUID-APPLIED FLOORING
More informationSpecifications. Specifications (Architectual) Metallic System. Metallic System
(Architectual) Metallic System Architectual NeverStrip Floor Coatings, 6-15 Mils Master Format Section 096700 Fluid Applied Flooring 1 of 6 NeverStrip Metallic High-Build Decorative Epoxy/Urethane Coating
More informationRESINOUS FLOORING
PART 1 - GENERAL 1.1 RELATED DOCUMENTS Bid #2017-17 A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this
More information1/16 Single Broadcast Polymer Flooring System
specification 1/16 Single Broadcast Polymer Flooring System Part 1 - GENERAL General Provisions A. Work to be covered by this section, under written specification or by drawing, shall comply with all provisions
More informationSECTION RESINOUS FLOORING PLEXIQUARTZ BROADCAST SKID-RESISTANT QUARTZ SYSTEM
SECTION 096723 RESINOUS FLOORING PLEXIQUARTZ BROADCAST SKID-RESISTANT QUARTZ SYSTEM PART 1 - GENERAL 1.1 SUMMARY A. This section includes the following: 1. Seamless epoxy flooring system, 1/16 th, 3/32
More informationA. This Section includes resinous flooring systems with epoxy body coat(s).
SECTION 096723 - RESINOUS FLOORING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes resinous flooring systems with epoxy body coat(s). 1. Application Method: Troweled (Slurry, Seeded or Broadcast
More informationSECTION EPOXY TERRAZZO
SECTION 09402 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to
More informationSection SECTION RESINOUS FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 096723 - RESINOUS FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION RESINOUS FLOORING or SECTION QUARTZ FLOORING
SECTION 09 67 23 RESINOUS FLOORING or SECTION 09 67 26 QUARTZ FLOORING PART 1 - GENERAL 1.1 SUMMARY (Specification writer shall add, delete or amend, as deemed necessary) A. Provide all labor, materials,
More informationFLEXMAR 3-Coat High-Build Colored Quartz System
Guide Specification SECTION 09 67 23: HIGH-PERFORMANCE RESINOUS FLOORING FLEXMAR 3-Coat High-Build Colored Quartz System 20-27 mils DFT This guide specification is intended to assist the specifier in developing
More informationPOLYACRYLATE MODIFIED THINSET TERRAZZO 1
PART 1 - GENERAL GUIDE SPECIFICATION POLYACRYLATE MODIFIED THINSET TERRAZZO - REVISED AUG 02 1.1 RELATED DOCUMENTS A. Section includes thin set Polyacrylate Modified Terrazzo flooring (and integral cove
More informationEPOXY TERRAZZO 1 REV. 8/02
PART 1 - GENERAL GUIDE SPECIFICATIONS section 9400 EPOXY THINSET TERRAZZO (Without A Crack Suppression Membrane) REVISED MAY 2003 1.1 RELATED DOCUMENTS A. Section includes thin-set epoxy terrazzo flooring
More informationFlorock Seamless Flooring Systems
Architectural Specification FloroBuild XT Extreme Impact & Abrasion Resistant Resurfacing System Part 1: General 1.01 System Description A. Roller applied 100% solids epoxy primer, followed by an extreme
More information1/4 Industrial Trowel System
System Specification 1/4 Industrial Trowel System Revision Date: 6/2015 Printed Date: 6/2015 PART 1 GENERAL 1.01 RELATED DOCUMENTS Drawings and general provisions of contract including General and Special
More informationTennant Company October North Lilac Drive Minneapolis, Minnesota Guide Specification
October 2016 701 North Lilac Drive Minneapolis, Minnesota 55422 800-553-8033 www.tennantco.com info@tennantco.com Guide Specification SECTION09 67 23 RESINOUS FLOORING (Tennant Epoxy Flake SR-HTS) PART
More informationSECTION RESINOUS FLOORING
SECTION 096723 - RESINOUS FLOORING PART I GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationDesco Quartz Cremona Specifications
Desco Quartz Cremona Specifications PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Sections, apply
More informationFlorock Seamless Flooring Systems
Part 1: General Florock Seamless Flooring Systems Architectural Specification FloroQuartz BC Epoxy - Colored Quartz 1/8 (0.125 mm) Double Broadcast Flooring System 1.01 System Description A. Roller-applied
More informationDesco Granite Flooring Specifications
Desco Granite Flooring Specifications PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Sections, apply
More informationSECTION RESINOUS FLOORING
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 67 23 1. Use this section only for NCA projects. 2. Delete // // if not applicable to project. Also delete any other item or paragraph not applicable in the
More informationFlorock Seamless Flooring Systems
Architectural Specification -- FloroCryl Shop MMA (Methyl Methacrylate) - Silica Sand Single Broadcast 1/16 (1.59 mm) Flooring System Part 1: General 1.01 System Description A. Roller-applied penetrating
More informationFlorock Seamless Flooring Systems
Architectural Specification FloroBuild PT/ HT Epoxy Mortar ¼ Power Trowel or Hand Trowel Flooring System Part 1: General 1.01 System Description A. Roller-applied 100% solids, penetrating epoxy primer
More informationSection Pedestrian Traffic Coatings
Guide Specification MiraFlex II - For Concrete Surfaces Pedestrian Deck and Waterproofing System (Specification writer shall choose the most appropriate section that applies to a given scope of work, including
More informationSECTION HYDRAULIC CEMENT UNDERLAYMENT
ARDEX GUIDE SPECIFICATION ARDEX K 520 Self-Leveling Concrete Topping Self-Leveling Topping for Indoor Fast-Track Resurfacing SECTION 03 54 16 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general
More informationSECTION CONCRETE TOPPING or SECTION DECORATIVE FINISHING or SECTION CEMENTITIOUS COATINGS
CSI Master Format does not currently include a specific section number for Cementitious Microtopping Flooring systems. Specification writer shall choose the most appropriate section that applies to the
More information1/8 DECORATIVE BROADCAST FLOORING SYSTEM
AIA specification AIA specification AIA Specification 1/8 DECORATIVE BROADCAST FLOORING SYSTEM Part 1 - GENERAL General Provisions A. Work to be covered by this section, under written specification or
More information1.2 SUMMERY A. Section Includes: 1. High-Performance Polyurethane Resinous flooring systems. 2. Decorative Polyurethane Resinous flooring systems.
PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and supplementary Conditions and Division 01 Specification Sections apply to this Section. 1.2
More informationDECOFLAKE DECORATIVE FLOORING SYSTEM
AIA Specification DECOFLAKE DECORATIVE FLOORING SYSTEM Part 1 - GENERAL General Provisions A. Work to be covered by this section, under written specification or by drawing, shall comply with all provisions
More informationDECOCOLOR FLOORING SYSTEM
AIA Specification DECOCOLOR FLOORING SYSTEM Part 1 - GENERAL General Provisions A. Work to be covered by this section, under written specification or by drawing, shall comply with all provisions of the
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 096623 - RESINOUS MATRIX TERRAZZO FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationBroadcast Parking Garage System
AIA Specification Part 1 General Broadcast Parking Garage System 1.01 Work Included A. All work to be provided in this section shall include material, labor, and equipment necessary to furnish the complete
More informationSECTION ELASTOMERIC LIQUID FLOORING
SECTION 096713 - ELASTOMERIC LIQUID FLOORING PART I GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification
More informationBROADCAST KITCHEN FLOORING SYSTEM
AIA specification AIA specification AIA Specification Part 1 - GENERAL BROADCAST KITCHEN FLOORING SYSTEM General Provisions A. Work to be covered by this section, under written specification or by drawing,
More informationSECTION EPOXY TERRAZZO TILE WITH RECYCLED GLASS MATRIX
GlassPLANK GUIDE SPECIFICATION Manufacturer: GLASS RECYCLED LLC 2939 Irving Blvd Suite 305 Dallas TX 75247 (888) 523-7894 toll free voice www.glassrecycled.com SECTION 09 66 18 EPOXY TERRAZZO TILE WITH
More informationEngine Bay Floors Floor Resurfacing 4000
Engine Bay Floors Floor Resurfacing 4000 P.O. Box 341 Macungie, PA 18062 610.530.7710 800.573.9198 www.enginebayfloors.com 1.1 SUBMITTALS Flooring Specification SECTION 1 GENERAL A. Product Data: Submit
More informationMRXL4 CR6 Surface Requirements: XNS, NS, M, S; Special Requirements: NO PART 1 : GENERAL
PART 1 : GENERAL 1.01 DESCRIPTION A. WORK INCLUDED: All labor, materials, appliances, tools, equipment, facilities, transportation and services necessary for and incidental to performing all operations
More informationSECTION SUBSURFACE PREPARATION FOR FLOOR FINISHES
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 05 16 SUBSURFACE PREPARATION FOR FLOOR FINISHES SPEC WRITER NOTES: 1. Delete between // // if not applicable to project. Also delete any other item or paragraph
More informationNORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017
SECTION 09 6613 - PORTLAND CEMENT TERRAZZO FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX Products
ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX Products SECTION 09 05 61.13 MOISTURE VAPOR EMISSION CONTROL PART 1 - GENERAL 1.1 RELATED DOCUMENTS
More informationARDEX GUIDE SPECIFICATION ARDEX SD-M Designer Floor Finish
ARDEX GUIDE SPECIFICATION ARDEX SD-M Designer Floor Finish SECTION 03 01 30 MAINTENANCE OF CAST-IN-PLACE CONCRETE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general provisions of the Contract,
More informationPacific Polymers Elasto-Deck 5000X2 Guide Specification
1 071813-1 July 2018 Pacific Polymers Elasto-Deck 5000X2 Guide Specification SECTION 071813 TRAFFIC COATINGS ELASTO-DECK 5000X2 OVER CONCRETE 2 071813-2 July 2018 Pacific Polymers Elasto-Deck 5000X2 Guide
More informationSECTION Verrazzo Epoxy Mosaic Floor System
THIS IS A SAMPLE SPECIFICATION FOR THE INDICATED PRODUCT. IT IS THE RESPONSIBILITY OF THE SPECIFIER AND/OR END USER TO DETERMINE THE SUITABILITY OF A PRODUCT OR SYSTEM FOR A PARTICULAR PURPOSE. Specifier
More informationFlorock Seamless Flooring Systems
Architectural Specification Florotallic Epoxy and Urethane Flooring System Part 1: General 1.01 System Description A. Roller-applied 100% solids, penetrating epoxy primer, decorative pigmented epoxy coatings
More informationPacific Polymers Elasto-Deck 5000MR Guide Specification
1 071813-1 July 2018 Pacific Polymers Elasto-Deck 5000MR Guide Specification SECTION 071813 TRAFFIC COATINGS ELASTO-DECK 5000MR OVER CONCRETE 2 071813-2 July 2018 Pacific Polymers Elasto-Deck 5000MR Guide
More informationSECTION MOISTURE RESISTANT/WATER-PROOF FLOORING ADHESIVE FOR CONCRETE SLABS
SECTION 09699 MOISTURE RESISTANT/WATER-PROOF FLOORING ADHESIVE FOR CONCRETE SLABS PART 1 GENERAL 1.1 SECTION INCLUDES A. Testing and application of systems for the reduction of moisture resistant or water-proof
More informationARDEX GUIDE SPECIFICATION ARDEX K 521 Self-Leveling Concrete Topping with Aggregate Surface
ARDEX GUIDE SPECIFICATION ARDEX K 521 Self-Leveling Concrete Topping with Aggregate Surface SECTION 03 54 16 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general provisions of the Contract, and
More informationFlorock Seamless Flooring Systems
Architectural Specification FloroCrete RT Rake/Trowel Urethane Mortar 3/16-1/4 (4.5-6.0 mm) Floor Resurfacing System Part 1: General 1.01 System Description A. System I Skid-Resistant Finish Resurfacing
More informationFlorock Seamless Flooring Systems
Architectural Specification Florotallic Epoxy and Urethane Flooring System Part 1: General 1.01 System Description A. Roller-applied 100% solids, penetrating pigmented epoxy primer, decorative pigmented
More informationPRODUCT SPECIFICATIONS
PART 1 GENERAL 1.01 SUMMARY A. Section Includes: High density cast resin architectural products, including columns, panels, caps, bases, trim elements and balustrade systems. Specifier Note: Article below
More informationAdvantages: Advantages include:
Elgin, Illinois Hi-Tek Polymers Floor Description: Hi-Tek Polymers Floor is a decorative thin-set epoxy system of 1/4" (6,3mm) to 3/8 (MM) which meets all the standards set by the NTMA (National Terrazzo
More informationARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX Underlayments and Toppings
ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX Underlayments and Toppings SECTION 07 26 19 TOPICAL MOISTURE VAPOR MITIGTION SYSTEM PART 1 - GENERAL
More information3/16-1/4 Urethane Concrete Slurry System
3/16-1/4 Urethane Concrete Slurry System PART 1 GENERAL 1.01 RELATED DOCUMENTS Drawings and general provisions of contract including General and Special Conditions and Division I, excepting special Submittal
More information1.3 Work shall include all reinforcement and accessories necessary to complete installation.
CERAMIC TILING GENERAL INFORMATION 1.1 Ceramic mosaic tile floors and bases, glazed wall tile wainscots and walls, and marble thresholds. 1.2 Installation will typically be with latex-portland cement mortar
More informationBush Elem. Addition & Alterations QUARRY TILE SECTION QUARRY TILE PART 1 - GENERAL
73651.01 QUARRY TILE 093016-1 1.1 RELATED DOCUMENTS: SECTION 093016 - QUARRY TILE PART 1 - GENERAL A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division
More informationSECTION EPOXY MOSAIC COMPOSITION FLOORING Dex-O-Tex Cheminert Terracolor
SECTION 09720 EPOXY MOSAIC COMPOSITION FLOORING Dex-O-Tex Cheminert Terracolor PART 1.00 - GENERAL 1.01 GENERAL REQUIREMENTS A. Work of this Section, as shown or specified, shall be in accordance with
More informationGUIDE SPECIFICATION SECTION 07576
GUIDE SPECIFICATION SECTION 07576 TRAFFIC DECK MEMBRANE SYSTEM NOTE TO ARCHITECTS & ENGINEERS: The Oak Ridge traffic membrane system provides for applied high build, durable and waterproof membrane consisting
More information***************************************************************************************************************
09330 QUARRY TILE *************************************************************************************************************** SPECIFIER: CSI MasterFormat 2004 number 09 30 16 ***************************************************************************************************************
More informationFlorock Seamless Flooring Systems
Architectural Specification -- FloroCryl Deck- 1/8 (125 mil) MMA (Methyl Methacrylate) Waterproofing 1/8 Flooring System Part 1: General 1.01 System Description A. Roller-applied penetrating MMA primer
More informationTILE TILE
09300 - TILE 09300-1 PART ONE: GENERAL 1.1 Description TILE 1.1.1 Work of this Section, as shown or specified, shall be provided by the Interior Contractor and shall be in accordance with the requirements
More informationDUR-A-FLEX, Inc. Page 1 of 5
DUR-A-FLEX, Inc. Page 1 of 5 SECTION 09 67 23-RESINOUS FLOORING DUR-A-GARD EPOXY COATING WITH URETHANE (Armor Top) TOPCOAT (23 mils) Date:01/13 PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general
More informationDesco Mosaic Flooring Specifications
Desco Mosaic Flooring Specifications PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Sections, apply
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 096519 - RESILIENT TILE FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationDecorative Quartz Floor Coating System
Decorative Quartz Floor Coating System 1.01 - Work Included 1. Furnish necessary material, labor, and equipment required to prepare designated areas and install a DecoFloor Quartz System 2. Submit three
More informationEasy to apply Nonflammable Low odor Castable Make excellent materials of construction
SELECTION & SPECIFICATION DATA Generic Type Description Features Color Primer Application Thickness Dry Film Thickness Typical Uses Polymer Concrete polymer concrete is an excellent alternative to acid
More informationCSI GUIDE Countertops
CSI GUIDE Countertops Part 1 General 1.0 RELATED DOCUMENTS A. Drawings and general provisions of the contract, including general and supplementary conditions and Division 1 Specification Sections, apply
More informationKOSTER AMERICAN CORPORATION
Section 09699 PART 1 GENERAL Water Vapor Emission Control Systems 1.1 RELATED DOCUMENTS A. Drawings, documents, and general provisions of the Contract, including, but not necessarily limited to, General
More informationSECTION FLUID-APPLIED WATERPROOFING
SECTION 07140 FLUID-APPLIED WATERPROOFING PART 1 GENERAL 1.1 SUMMARY A. Section includes fluid applied rubberized asphalt and/or elastomeric membrane waterproofing; and surface dusting and/or protective
More informationARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX ARDIFLO Pump System Underlayments
ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX ARDIFLO Pump System Underlayments SECTION 07 26 19 TOPICAL MOISTURE VAPOR EMISSION SYSTEM WITH ARDEX
More informationSECTION RESINOUS FLOORING
SECTION 09705 PART I - GENERAL 1.01 DESCRIPTION A. Scope: Work of this Section includes all materials and installation necessary to provide resinous flooring system with integral cove base and top finish
More informationSECTION RESILIENT SHEET FLOORING
SECTION 09 65 16 RESILIENT SHEET FLOORING SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1.
More informationSECTION TERRAZZO FLOOR TILE
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 66 16 SPEC WRITER NOTES: 1. Use this section only for NCA projects. 2. Delete between // ----- // if not applicable to project. Also delete any other item or
More informationConsult Sika Corporation (Industrial Flooring) for assistance in editing this section for the specific application.
THIS IS A SAMPLE SPECIFICATION FOR THE INDICATED PRODUCT. IT IS THE RESPONSIBILITY OF THE SPECIFIER AND/OR END USER TO DETERMINE THE SUITABILITY OF A PRODUCT OR SYSTEM FOR A PARTICULAR PURPOSE. Specifier
More informationA. This Section includes traffic coatings for the following applications:
SECTION 071800 - TRAFFIC COATINGS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes traffic coatings for the following applications: 1. Interior and exterior, pedestrian traffic. 2. Vehicular traffic.
More informationTnemec Fluid Applied Thermal Break Long Form Specification
PART 1 GENERAL 1.01 DESCRIPTION Tnemec Fluid Applied Thermal Break Long Form Specification A. This specification covers labor, materials, equipment, and application necessary for, and incidental to, the
More informationB. American Concrete Institute 1. ACI 302, 1R-89 Guide for Concrete Floor and Slab Construction
SECTION 03360- CONCRETE FINISHES SPECIALIZED TERR-CON FLOORING SYSTEM PART 1-GENERAL 1.01 SUMMARY A. This section includes the following: 1. Standard placement of concrete and Terr-Con Aggregate 2. Grinding
More informationSECTION SELF-ADHERING SHEET MEMBRANE WATERPROOFING
SECTION 07 13 26 PART 1 - GENERAL 1.1 SUMMARY A. Scope: 1. Apply waterproofing to: a. Exterior of walls below grade: 1) Waterproofing shall include exterior of walls surrounding elevator pits and sumps.
More informationThis Section includes surface preparation and field application of anti-graffiti coating systems for the following vertical and horizontal surfaces:
0 0 0 0 0 0 SECTION 0 ANTI- GRAFFITI COATINGS PART - GENERAL RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division Specification
More information(Specification writer shall choose the most appropriate section that applies to a given scope of work) SECTION Painting and Coating
Guide Specification Miracote Mirastain Architectural Staining System (Specification writer shall choose the most appropriate section that applies to a given scope of work) PART 1 - GENERAL 1.1 SUMMARY
More informationFlorock Seamless Flooring Systems
Architectural Specification Floropoxy/Florospartic 5 Self-Leveling Epoxy/Polyaspartic Flooring System Part 1: General 1.01 System Description A. Roller applied 100% solids, penetrating pigmented epoxy
More informationApplication Specification:
Application Specification: GW-15-UBU-HP April 2014 Supersedes 5/13 PART 1 - GENERAL 1.1 SUMMARY Division 07 18 16: GACOFLEX POLYURETHANE ELASTOMERIC COATING SYSTEM FOR HELICOPTER PADS A. This section describes
More informationMDC MicroTex Eggshell Micro-Textured Ceramic Coating for Walls
MicroTex Eggshell Micro-Textured Ceramic Coating for Walls Specification Guide 95: 9770 Special Wall Finishes 88: 9800 Special Coatings Part 1 General 1.01 SUMMARY A. This section specifies the furnishing
More informationFlorock Seamless Flooring Systems
Part 1: General Architectural Specification FloroCrete SLX Self-Leveling Urethane Mortar w/broadcast nominal 3/16 Flooring System 1.01 System Description A. Squeegee/Troweled-applied, aggregate-rich polyurethane
More informationARDEX GUIDE SPECIFICATION ARDEX PC-M POLISHED CONCRETE MICRO-TOPPING Part of the ULTRAFLOR ARDEX DIAMATIC Polished Concrete System
ARDEX GUIDE SPECIFICATION ARDEX Part of the ULTRAFLOR ARDEX DIAMATIC Polished Concrete System SECTION 03 35 44 POLISHED CONCRETE MICRO-TOPPING PART I GENERAL 1.01 SUMMARY A. This is the recommended specification
More informationDUR-A-FLEX, Inc. Page 1 of 6
DUR-A-FLEX, Inc. Page 1 of 6 SECTION 09 67 23-RESINOUS FLOORING DUR-A-CHIP EPOXY BROADCAST WITH URETHANE TOPCOAT Date:01/13 PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the
More informationSPECIAL SPECIFICATION 2042 Decorative Colored Pattern Concrete Paving
2004 Specifications CSJ 0196-02-120 SPECIAL SPECIFICATION 2042 Decorative Colored Pattern Concrete Paving 1. Description. This Item shall govern for the furnishing and placing of colored concrete wave
More informationA. Section includes hydraulic-cement-based, polymer-modified, self-leveling underlayment for application below interior floor coverings.
SECTION 03 54 16 - HYDRAULIC CEMENT UNDERLAYMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationSpecifier Notes: Edit the following list as required by the project. List other sections with work directly related to the floor coating.
This specification covers an epoxy wall coating system composed of an epoxy block filler, one or two applications of a flexible hybrid polymer basecoat, and top coat of high-performance aliphatic satin
More informationA. Section includes cast-in-place concrete, including reinforcement, concrete materials, mixture design, placement procedures, and finishes.
SECTION 033053 - CONCRETE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationSECTION RESILIENT TILE FLOORING. A. Section includes vinyl composition floor tile and accessories indicated and as specified.
SECTION 09 65 19 RESILIENT TILE FLOORING PART 1 - GENERAL 1.1 SUMMARY A. Section includes vinyl composition floor tile and accessories indicated and as specified. 1.2 SUBMITTALS A. Product Data: Submit
More informationSECTION EPOXY RESIN FLOORING WITH INTEGRAL COVE BASE
SECTION 09730 EPOXY RESIN FLOORING WITH INTEGRAL COVE BASE PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 03300 - Cast-in-Place Concrete. 2. 09000 - Patching and Finishes. 3. 09900 - Painting. 4.
More informationSECTION CONCRETE PAVING SLABS SET IN MORTAR
SECTION 32 14 13.16 CONCRETE PAVING SLABS SET IN MORTAR (1995 MasterFormat Section 02784) Note: This guide specification for the U.S. is for paving slabs mortared to a concrete base and grouted joints
More informationSECTION (07100) - DAMPPROOFING AND WATERPROOFING
SECTION 07 10 00 (07100) - DAMPPROOFING AND WATERPROOFING PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Sheet Membrane Waterproofing 2. Under-Slab-On-Grade Vapor Barrier B. Related Sections: 1.02
More informationCARLISLE DECK COATING INSTALLATION OVER EXISTING POLYURETHANE COATINGS
CARLISLE DECK COATING INSTALLATION OVER EXISTING POLYURETHANE COATINGS 1. GENERAL A. When coating over existing coatings, Carlisle can not assume responsibility for the adhesion of the existing coating,
More informationRECOMMENDED DESIGN SPECIFICATION
RECOMMENDED DESIGN SPECIFICATION SILICONE COATED SPF ROOFING 1 General 1.1 Section Includes A. Silicone coated SPF roofing system, including substrate board, roof insulation boards, foam insulation materials,
More informationARCHITECTURAL GUIDE SPECIFICATIONS - DESCRIPTIVE
ARCHITECTURAL GUIDE SPECIFICATIONS - DESCRIPTIVE MANNINGTON COLORFIELDS SHEET RUBBER FLOORING Section 09 65 16 Sheet rubber Flooring (Thermoset Rubber) Created May 2012 Mannington Mills, Inc. P. O. Box
More informationMulti-Institutional Academic Health Science & Research Center Evansville, IN
SECTION 07 1616 - CRYSTALLINE WATERPROOFING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationJewel Stone. Decorative Concrete Overlay System. Part 1 GENERAL MANUFACTURER S SPECIFICATION
SEPTEMBER 2016 Jewel Stone Decorative Concrete Overlay System MANUFACTURER S IFICATION 09 62 81 Part 1 GENERAL 1.1 RELATED SECTIONS.1 Specification 03 30 00 Cast-in-Place Concrete.2 Specification 09 70
More informationSECTION GYPSUM BOARD ASSEMBLIES
SECTION 09260 GYPSUM BOARD ASSEMBLIES PART 1 GENERAL 1.1 SUMMARY A. Provide gypsum board assemblies. 1.2 SUBMITTALS A. Product Data: Submit manufacturer's product data and installation instructions for
More informationApplication Specification:
Application Specification: GW-15-UBU-HD April 2014 Supersedes 5/13 PART 1 - GENERAL 1.1 SUMMARY Division 07 18 16: GACOFLEX POLYURETHANE ELASTOMERIC COATING SYSTEM FOR VEHICULAR TRAFFIC DECKS AND RAMPS
More informationDist. by: BEST MATERIALS Ph:
Dist. by: BEST MATERIALS Ph: 800-474-7570 www.bestmaterials.com Email: Sales@BestMaterials.com NOVALINK SL SELF-LEVELING CONSTRUCTION SEALANT DIVISION 7 - THERMAL AND MOISTURE PROTECTION SECTION 07 92
More information