Performance of a counterflow heat exchanger with heat loss through the wall at the cold end
|
|
- Abigayle Rose
- 6 years ago
- Views:
Transcription
1 Cryogenics 39 (1999) 43 5 Performance of a counterflow heat exchanger with heat loss through the wall at the cold end S. Pradeep Narayanan, G. Venkatarathnam * Department of Mechanical Engineering, Indian Institute of Technology, Chennai , India Received 7 July 1998; accepted 9 November 1998 Abstract The performance of high effectiveness heat exchangers used in cryogenic systems is strongly controlled by irreversibilities such as longitudinal heat conduction and heat leak from ambient. In all heat exchanger analyses, it is assumed that no heat is lost through the heat exchanger walls. In the case of small J-T refrigerators such as microminiature refrigerators, the heat exchanger cold end is almost directly connected to the evaporator, which may result in a large amount of heat loss through the heat exchanger wall at the cold end. The rate of heat loss through the wall at the cold end is also strongly dependent on the longitudinal thermal resistance of the wall. In this paper, we present the relationship between the effectiveness of a heat exchanger losing heat at the cold end and other resistances such as number of transfer units (NTU), longitudinal thermal resistance etc. The performance of such heat exchangers under different operating conditions is also discussed Elsevier Science Ltd. All rights reserved. Keywords: Compact heat exchangers; Heat leak; High effectiveness; Longitudinal heat conduction Nomenclature A Surface area of heat transfer (m ) A c Cross-sectional area of the walls (m ) C Heat capacity rate of fluids defined by the product of m and C p (W/K) c p Specific heat capacity at constant pressure (J/kg K) h Heat transfer coefficient (W/m K) i Heat exchanger ineffectiveness l- k Thermal conductivity of the wall material (W/m K) L Heat exchanger length (m) m Mass flow rate (kg/s) ntu Number of transfer units for individual fluid sides NTU Overall number of transfer units r j Roots of characteristic equation T Temperature (K) W Width of a counterflow heat exchanger (m) x Axial co-ordinate (m) * Corresponding author. Tel: ; fax: ; gvenkat@acer.iitm.ernet.in X Dimensionless axial co-ordinate in the exchanger defined by x/l Greek Dimensionless temperature, defined as (T T h,in )/(T T c,in ) Effectiveness of the heat exchanger Dimensionless axial conduction parameter, defined as (ka c /LC min ) Ratio of heat capacity rates (C h /C min ) Ratio of heat capacity rates (C c /C h ) Dimensionless heat leak at the cold end of the heat exchanger q Heat transfer rate (W) Subscripts c h in min max out w Cold fluid Hot fluid Inlet Fluid of lower heat capacity rate Fluid of higher heat capacity rate Outlet Wall /99/$ - see front matter 1999 Elsevier Science Ltd. All rights reserved. PII: S (98)0013-4
2 44 S. Pradeep Narayanan, G. Venkatarathnam / Cryogenics 39 (1999) Introduction The performance of low effectiveness heat exchangers is largely dependent on the finite heat transfer area (heat transfer coefficients), and can be predicted fairly accurately using conventional -NTU or Log mean temperature difference (LMTD) methods. The performance of high effectiveness heat exchangers such as those used in cryogenic systems, on the other hand, is dependent on other irreversibilities such as longitudinal (axial) heat condition through the walls and heat leak from the ambient. Different authors [1 3] have studied the effect of these two irreversibilities on the performance of heat exchangers and have presented the relationship between attainable effectiveness and the traditional number of transfer units (NTU), the lateral conduction resistance and the rate of heat leak into the heat exchangers. A common assumption made by all the authors analysing the performance of heat exchangers is that the walls of the heat exchanger are insulated at either end, i.e. there is no heat transfer by conduction at the two ends of the heat exchanger. Such an assumption is, however, not valid in the case of a microminiature cryogenic refrigerator. Fig. 1 shows the schematic of a microminiature refrigerator, which operates on the Linde cycle (Fig. ). In the microminiature refrigerator (MMR) the heat exchanger, expansion capillary and the evaporator are all etched on a thin sheet of glass or stainless steel [4,5]. The typical size of a microminiature refrigerator is mm. In any MMR, a temperature gradient of about 5 K is sustained between the two ends of the refrigerator within a short distance (typically mm). Unlike a normal heat exchanger, the cross-sectional area of the walls of the heat exchanger is much larger than the flow cross-section in a MMR. Longitudinal heat conduction through the walls will therefore be much higher in MMR heat exchangers compared to other type of cryogenic heat exchangers. Because of the small distance between the cold end of the heat exchanger and the evaporator, a significant part of the heat conducted through the wall will be transferred to the evaporator. The loss of refrigeration due to the parasitic heat conduction through the walls can be quite significant. Hence, the assumption of insulated cold end (i.e. no heat transfer between the heat exchanger walls and the evaporator) cannot be applied in the case of microminiature refrigerator heat exchangers. The Coefficient of Performance (COP) attainable in a J-T cryocooler is strongly dependent on the effectiveness of the heat exchanger used and the operating pressures. It can be shown that no refrigeration can be realized in most refrigerators if the effectiveness of the heat exchanger is less than 85% [6]. The minimum heat exchanger effectiveness necessary for the Linde cycle process to be feasible will be even higher in the case of Fig. 1. Schematic of a microminiature refrigerator. MMR because of the significant parasitic heat conduction through the walls. The minimum effectiveness necessary for a microminiature refrigerator to function, cannot, however, be evaluated using conventional heat exchanger effectiveness expressions because of the heat conduction between the cold end of the heat exchanger and the evaporator. In order to estimate the performance of microminiature refrigerators accurately, the relationship between the heat conducted at the cold end of the exchanger, the convective heat transfer between the
3 S. Pradeep Narayanan, G. Venkatarathnam / Cryogenics 39 (1999) equations for the hot fluid, cold fluid and the wall are obtained by energy balance as follows: Hot fluid: d h dx ntu h( h w ) 0 (1) Cold fluid: d c dx ntu c( w c ) 0 () Wall: d h dx d c dx d w 0 (3) dx Fig.. Linde cycle refrigerator. In the above expressions, h, c and w represent the dimensionless temperature of the hot fluid, cold fluid and the separating wall respectively: streams and the longitudinal heat conduction along the wall should be clearly understood. The main aim of this paper is to derive the expressions relating the parasitic heat conducted at the cold end of the heat exchanger, the NTUs and axial conductance of the wall. In the following sections, the governing equations of a counterflow heat exchanger which is losing heat through the wall at the cold end are solved, and closed form expression derived for the heat conducted at the cold end, and the effectiveness of the exchanger in terms of number of transfer units NTU and axial conduction parameter in the case of balanced flow ( 1) heat exchangers. For unbalanced flow ( 1) exchangers, the governing equations have been solved numerically and the results are presented in graphical form. The performance of heat exchangers with heat loss at the cold end is compared with conventional heat exchangers with insulated ends.. Mathematical model Let us consider a counterflow heat exchanger in which longitudinal heat conduction is non-negligible and the exchanger subjected to heat loss at the cold end (Fig. 3). Let the length of exchanger be L. The governing Fig. 3. Heat exchanger model. t t c,in t h,in t c,in ka c C min X x L ntu h ha Ch C c C h ntu c ha Cc C h C min (4) where ntu h and ntu c are the number of heat transfer units of the hot and cold fluid streams, respectively; is the heat capacity rate ratio and the longitudinal heat conduction parameter defined as follows: x 0: h 1, d w dx 0 (5) x 1: c 0, w 1 w (6) Assuming that the wall is insulated at the hot end, and conducting at the cold end, the boundary conditions can be expressed as follows: x 1: c 0, w 0 (7) The heat loss to the surrounding area from the cold end will be maximum when w 0. The above condition therefore represents the maximum degradation possible due to combined longitudinal conduction and heat loss to surroundings at the heat exchanger cold end. In a real situation, the wall temperature at the cold end is decided by the heat transfer resistance between the heat exchanger and the surroundings (evaporator). In order to estimate the true performance, the governing equations, however, need to be solved together with that for the heat transfer between the heat exchanger and the evaporator to estimate the true performance of the heat exchanger and the amount of heat loss through the wall at the cold end of the heat exchanger. General solutions can not be obtained when the heat transfer resistance between the wall and ambient at the cold end is also considered. On the other hand, closed form general sol-
4 46 S. Pradeep Narayanan, G. Venkatarathnam / Cryogenics 39 (1999) 43 5 utions can be obtained when w approaches zero (i.e. the thermal resistance between the exchanger and the evaporator is assumed to be negligible). The boundary condition expressed in Eq. (7) is therefore preferable over the more general boundary condition expressed in Eq. (6). In the following sections the governing equations are solved with the boundary condition given by Eq. (7). 3. Balanced flow exchanger (C min C max ) The governing equations, Eqs. (1) (3) have been solved along with the boundary conditions (Eqs. (5) (7)) for a balanced flow condition (C h C c ), to obtain closed form expressions for the exit temperature of the hot and cold fluid streams as follows: h,out (8) (1 a 1 ) NTU (1 a 1 )1 NTU 1 a 1 r e r 31 (er 3 a 3 ) ntu h ntu h r e r (e r a ) 1 ntu r 3 h ntu h r 3 e r 3 c,out 1 (9) (a 1 1) 1 NTU (1 a 1 )1 NTU 1 a 1 ntu r h e ntu h r r 1 r 3 ntu h ntu h r 3 e r 3 where r, r 3 are the eigen roots of the governing equations and are defined as follows: r ntu h ntu c ntu h ntu c ntu h ntu c r 3 ntu h ntu c ntu h ntu c ntu h ntu c (10) (11) In the above expressions a 1, a and a 3 are defined as follows: a 1 1 a 3e r 3 a 1 a e r ntu h (1) ntu h r a 3 ntu h ntu h r 3 Because of space limitations only the final expressions for the exit temperature of the hot and cold fluid streams are presented here. The dimensionless heat loss at the cold end can be expressed in terms of the number of transfer units and the longitudinal heat conductance as follows: dt w ka c dx C min (t h,in t c,in ) d w dx (13) The heat loss at the cold end of the heat exchanger can be expressed in dimensionless form as follows: (14) 1 1 e r 3 (1 a 1 )1 NTU 1 a 1 r a r 3 ntu h ntu h r e r e r 4. Effectiveness of the heat exchanger ntu h ntu h r 3 e r 3 The effectiveness of any heat exchanger is defined as the ratio of actual heat transfer to the maximum possible heat transfer. Because of the heat loss at the cold end, the total heat transferred by the hot fluid stream is not equal to the total heat transferred to the cold fluid stream. Therefore the usual definition of heat exchanger effectiveness cannot be used. The effectiveness of the heat exchanger can be defined separately in terms of the heat transfer to the hot and cold fluid streams as follows: h q hot C h(t h,out t h,in) q max C min (t h,in t c,in ) c q cold C c(t c,out t c,in) q max C min (t h,in t c,in ) (15) (16) The above expressions can be expressed in terms of dimensionless fluid temperatures for a balanced flow heat exchanger as follows: h 1 h,out (C h C c ) (17) c c,out (C h C c ) (18) The two effectiveness expressions are related to the dimensionless heat transfer at the cold end as follows: h c (19) 4.1. Limiting case (C c C h and NTU ) When the number of transfer units approaches infinity, the expressions for the temperature of the hot and cold
5 S. Pradeep Narayanan, G. Venkatarathnam / Cryogenics 39 (1999) fluid streams at the heat exchanger exit, and the heat conducted at the cold end wall reduces to the following simple expressions: h,out 0; c,out 1 1 ; h 1; c 1 1 ; (0) 1 ;(C h C c ) When the axial heat conduction through the wall is negligible Eqs. (15) and (16) reduce to the following standard expression for counterflow heat exchangers [7]. h c NTU NTU 1 5. Unbalanced flow exchanger (C min C max ) (1) The solution of the governing equations of an unbalanced heat exchanger is not as straight forward as in the case of a balanced flow heat exchanger and the governing equations need to be solved numerically to obtain the heat exchanger performance. Following Kroeger [1], it has been assumed that the per side ntu is the same for both the fluid channels. ntu h ntu c ntu () The above assumption greatly simplifies the procedure and makes the solutions tractable. The numerical solution of the governing equations with ntu h not the same as ntu c indicated that the maximum difference between the heat conducted when ntu h was not equal to ntu c and that when ntu h ntu c is limited to about 3% in the range 0.8 ntu h /ntu c 1.5. With the above assumption, the exit temperature of the hot and cold fluid streams can be expressed as follows: h,out ( 1) A C B C (3) c,out D C (4) where the matrices A, B, C and D are defined as follows: A a1e r1 ae r a3e r e r 1 r 1 e r r e r3 r 3 (5) B (6) (1 a 1 r 1 ) e r 1 e r 1 e r e r r 1 (1 a r ) e r r (1 a 3 r 3 ) e r3 r 3 C (7) a1( e r1) a( e r) a3( e r3) (1 a 1 r 1 ) e r 1 (1 a r r ) e r (1 a 1 r 3 r 3 ) e r3 r 3 D (8) (1 a 1 r 1 ) e r 1 a 1 a a r 1 (1 a r ) e r r (1 a 3 r 3 ) e r3 r 3 In the above expressions r 1, r, and r 3 are the roots of the characteristic equation outlined below: r3 r ntu ntu 1 ( (9) 1)ntu 0 The effectiveness of the heat exchanger can be expressed in terms of the hot and cold fluid stream exit temperatures as follows: h (1 h,out ) h c,out (30) where 1 when hot fluid is the C min fluid and 1/, when cold fluid is the C min fluid. In both the cases is defined as follows: (ṁc p) c (ṁc p ) h C c C h (31) The dimensionless heat conducted through the wall at the cold end can be expressed in terms of the fluid exit temperatures as follows: h c (1 h,out ) c,out (3) 5.1. Limiting case (1 and ntu ) When the number of heat transfer units approaches infinity, the expressions for the exit temperature of hot
6 48 S. Pradeep Narayanan, G. Venkatarathnam / Cryogenics 39 (1999) 43 5 and cold fluid streams and the heat conducted through the wall at cold end reduce to the following expressions: h,out 0 c,out er 1 e r 1 (1 ) 1 e r (33) where r ( 1) (34) 6. Results and discussion The temperature profiles vary linearly with distance in a balanced flow ( 1) heat exchanger without any irreversibilities. The temperature profiles, however, get distorted due to longitudinal heat conduction and heat loss through the ends. Fig. 4 shows the temperature profile of the hot and cold fluid in a balanced flow (C h C c ) heat exchanger with an NTU of 0 and of 0.04, with heat transfer through the wall at the cold end of the heat exchanger. Fig. 5 shows that in an equivalent but fully insulated (normal) heat exchanger with the same design parameters. Because of the longitudinal heat conduction through the walls and the heat loss at the cold end, a balanced flow heat exchanger shows a profile similar to that of an unbalanced flow heat exchanger with hot fluid being the C min fluid. Because of the heat loss through the wall at the cold end, the hot fluid will cool more than that in a fully insulated heat exchanger, while the cold fluid heats less than that in a fully insulated heat exchanger. Figs. 6 0 show the variation of the hot fluid and the cold fluid outlet temperatures, as well as the dimensionless heat loss at the cold end as a function of the design (conventional) NTU, axial conduction parameter [8] and different heat capacity rate ratios. The heat trans- Fig. 5. Temperature profile of the hot and cold fluid streams in a normal heat exchanger with non-negligible longitudinal heat conduction. Fig. 6. Relation of hot fluid exit temperature to the NTU and longitudinal heat conduction parameter () for a balanced flow heat exchanger losing heat at the cold end. Fig. 4. Temperature profile of the hot and cold fluid streams in a normal heat exchanger with non-negligible longitudinal heat conduction and heat transfer through the wall at cold end. Fig. 7. Relation of hot fluid exit temperature to the NTU and longitudinal heat conduction parameter () for a balanced flow (C h /C c 0.8) heat exchanger losing heat at the cold end.
7 S. Pradeep Narayanan, G. Venkatarathnam / Cryogenics 39 (1999) Fig. 8. Relation of hot fluid exit temperature to the NTU and longitudinal heat conduction parameter () for a balanced flow (C c /C h 0.8) heat exchanger losing heat at the cold end. Fig. 11. Relation of cold fluid exit temperature to the NTU and longitudinal heat conduction parameter () for a balanced flow heat exchanger losing heat at the cold end. Fig. 9. Relation of hot fluid exit temperature to the NTU and longitudinal heat conduction parameter () for a balanced flow (C h /C c 0.6) heat exchanger losing heat at the cold end. Fig. 1. Relation of cold fluid exit temperature to the NTU and longitudinal heat conduction parameter () for a balanced flow (C h /C c 0.8) heat exchanger losing heat at the cold end. Fig. 10. Relation of hot fluid exit temperature to the NTU and longitudinal heat conduction parameter () for a balanced flow (C c /C h 0.6) heat exchanger losing heat at the cold end. ferred from the hot stream increases with an increase in NTU, as in a normal heat exchanger, resulting in a decrease in the temperature of the hot fluid at its outlet with an increase in NTU as shown in Figs at different heat capacity rate ratios. In normal heat exchangers with insulated ends, the hot fluid outlet temperature will increase with an increase in axial conduction parameter. However, when the wall at the cold end is directly connected to a cold sink, the hot fluid outlet temperature will decrease with an increase in axial conduction parameter as shown in Figs For example, h,out decreases by about 0% for an increase in from 0.01 to 0.08 for an NTU of 5 and 1. On the other hand, the cold fluid outlet temperature decreases with an increase in axial conduction parameter as in conventional heat exchangers at all heat capacity rate ratios (Figs ). At very large NTU, the hot
8 50 S. Pradeep Narayanan, G. Venkatarathnam / Cryogenics 39 (1999) 43 5 Fig. 13. Relation of cold fluid exit temperature to the NTU and longitudinal heat conduction parameter () for a balanced flow (C c /C h 0.8) heat exchanger losing heat at the cold end. Fig. 16. Relation of dimensionless heat loss at the cold end to the NTU and longitudinal heat conduction parameter () for a balanced flow heat exchanger losing heat at the cold end. Fig. 14. Relation of cold fluid exit temperature to the NTU and longitudinal heat conduction parameter () for a balanced flow (C h /C c 0.6) heat exchanger losing heat at the cold end. Fig. 17. Relation of dimensionless heat loss at the cold end to the NTU and longitudinal heat conduction parameter () for a balanced flow (C h /C c 0.8) heat exchanger losing heat at the cold end. Fig. 15. Relation of dimensionless heat loss at cold end to the NTU and longitudinal heat conduction parameter () for a balanced flow (C c /C h 0.6) heat exchanger losing heat at the cold end. Fig. 18. Relation of dimensionless heat loss at the cold end to the NTU and longitudinal heat conduction parameter () for a balanced flow (C c /C h 0.8) heat exchanger losing heat at the cold end.
9 S. Pradeep Narayanan, G. Venkatarathnam / Cryogenics 39 (1999) Fig. 19. Relation of dimensionless heat loss at the cold end to the NTU and longitudinal heat conduction parameter () for a balanced flow (C h /C c 0.6) heat exchanger losing heat at the cold end. Figs show the variation of heat leak at the cold end with NTU and for different heat capacity rate ratios. When the hot fluid is the C min fluid, or the flow is balanced (C c C h ), the heat leak at the cold end decreases with an increase in NTU as shown in Figs. 16, 17 and 19. When the cold fluid is the C min fluid, on the other hand, the heat leak increases within NTU as shown in Figs. 18 and 0 (see Eqs. (0) and (33)). It can also be seen that the heat loss at the cold end will be much smaller when the hot fluid is the C min fluid for the same operating parameters. It can be seen that the heat loss can be lower by up to 300% for NTUs of 6 or 7, and 0.6, when the hot fluid is the C min fluid, than when the cold fluid is the C min fluid. It should be remembered that the specific heat of pure fluids is, in general, higher at higher pressures. Therefore the cold fluid is the C min fluid when pure fluids are used in MMR refrigerators. The properties of some of the mixed refrigerants such as nitrogen hydrocarbon mixtures can be such that ( H/ T) p of the cold fluid stream is higher than that of the hot fluid stream over most of the heat exchanger length. The use of such mixtures in MMRs will therefore result in much lower parasitic heat conduction to the evaporator. 7. Conclusions Fig. 0. Relation of dimensionless heat loss at the cold end to the NTU and longitudinal heat conduction parameter () for a balanced flow (C c /C h 0.6) heat exchanger losing heat at the cold end. fluid temperature at outlet will approach that of the cold fluid at the inlet and the cold fluid temperature at the outlet will attain the value given by Eqs. (0) and (33) for balanced and unbalanced flows, respectively, as shown in Figs The liquid yield in a J-T liquefier will increase if the hot fluid (high pressure fluid) cools to a lower temperature before it is expanded in the J-T valve. The hot fluid outlet temperature will be lower in heat exchangers with heat leak at the cold end than in heat exchangers with insulated ends. Therefore, it may appear that the yield should increase because of the heat conduction at the cold end of the heat exchanger. However, the increase in yield is more than offset by the parasitic heat that enters the dewar (phase separator) from the heat exchanger leading to an overall reduction in the liquid yield or refrigerating capacity because of the heat transfer to surrounding at the cold end of the heat exchanger. The hot fluid will cool to a much lower temperature in a heat exchanger with heat loss at the cold than in an equivalent heat exchanger with insulated ends. Similarly, the cold fluid will heat to a temperature lower than that in a heat exchanger with insulated ends. For any given, the hot fluid exit temperature of the heat exchanger with conductive heat leak is always less than the hot fluid exit temperature of the heat exchanger with insulated ends. The difference can vary between 0 and 30% depending on NTU, and. The exit temperature of the cold fluid is, however, lower than that in an equivalent heat exchanger with insulated ends. The hot fluid exit temperature approaches zero as NTU of the heat exchanger approaches infinity, irrespective of the heat capacity rate ratios, while the outlet temperature of cold fluid and the heat leak at the cold end of the wall remains finite and a function of and. For a balanced flow and for an unbalanced flow with C h C min, the heat leak at the cold end wall () decreases with an increase in NTU, while for an unbalanced flow with C c C min, increases with an increase in NTU. Since the minimum fluid is the cold fluid (C c C min ) in MMR heat exchangers operating with nitrogen or argon, the degradation of perform-
10 5 S. Pradeep Narayanan, G. Venkatarathnam / Cryogenics 39 (1999) 43 5 ance due to heat leak increases with an increase in NTU of MMR exchangers. The performance of microminiature refrigerators will be better when operating mixed refrigerants which show a higher heat capacity rate in the cold fluid stream are used, compared to that operating with pure fluids, everything else being the same. The closed form expressions and limiting solutions derived give a new insight into MMR type heat exchanger performance, and should prove to be useful in the design and rating of heat exchangers employed in small J-T cryocoolers. References [] Barron RF. Effect of heat transfer from ambient on cryogenic heat exchanger performance. Advances in Cryogenic Engineering 1988;33:65 7. [3] Chowdhury K, Sarangi S. Performance of cryogenic heat exchangers with heat leak from the surroundings. Advances in Cryogenic Engineering 1988;33: [4] Little WA. Microminiature refrigerator. Review of Scientific Instruments 1984;55: [5] Mikulin EU. The miniature Joule Thomsen refrigerator. ICEC Supplement, Cryogenics 199;3: [6] Barron RF. Cryogenic systems, nd edn. Oxford University Press, UK, [7] Kays WM, London AL. Compact heat exchangers, nd edn. McGraw Hill, New York, USA, [8] Pradeep Narayanan S. Analysis of performance of microminiature refrigerator heat exchangers. MS Thesis, Indian Institute of Technology, Chennai, [1] Kroger PG. Performance deterioration in high effectiveness heat exchangers due to axial conduction effects. Advances in Cryogenic Engineering 1967;1:363 7.
Available online at ScienceDirect. Energy Procedia 105 (2017 )
Available online at www.sciencedirect.com ScienceDirect Energy Procedia 105 (2017 ) 4949 4954 The 8 th International Conference on Applied Energy ICAE2016 Theoretical Prediction of Longitudinal Heat Conduction
More information1. To improve heat exchange between a gas & a liquid stream in a heat exchanger, it is decided to use fins. Correct the suitable option.
1. To improve heat exchange between a gas & a liquid stream in a heat exchanger, it is decided to use fins. Correct the suitable option. a) Fins are generally attached on gas side. b) Fins are generally
More informationLab # BAEN/CHEN ! page 1 UNIT OPERATION IN FOOD PROCESSING Department of Biological and Agricultural Engineering Texas A&M University
Lab # BAEN/CHEN-422-622! page 1 Heat Exchanger Demonstration Lab Double Pipe HE Shell & Tube HE Tubular HE BAEN/CHEN-422-622! page 2 Heat Exchanger Demonstration Lab Summary The process of heat exchange
More information~ L Wang I D. XU,2 L. Fang,2 L. Zhang,2
.... BNL-66747...* Pmentcd atcryogenic Eogineaing Conferenceand International Cryogenic Materiala Cmkcnce July 12-16, 1999,Monad, Canada. STUDY ON THE VOLUMETRIC RATIO OF THE HYBRID GM REGENERATOR OVER
More informationModified Reverse-Brayton Cycles for Efficient Liquefaction of Natural Gas
Modified Reverse-Brayton Cycles for Efficient Liquefaction of Natural Gas H.M. Chang 1, J.H. Park 1, K.S. Cha 2, S. Lee 2 and K.H. Choe 2 1 Hong Ik University, Seoul, Korea 121-791 2 Korea Gas Corporation,
More informationOPTIMIZATION OF PARAMETERS FOR HEAT RECOVERY STEAM GENERATOR (HRSG) IN COMBINED CYCLE PLANTS
OPTIMIZATION OF PARAMETERS FOR HEAT RECOVERY STEAM GENERATOR (HRSG) IN COMBINED CYCLE PLANTS Muammer Alus, Milan V. Petrovic University of Belgrade-Faculty of Mechanical Engineering, Laboratory of Thermal
More informationNumerical model of a micro-structured heat exchanger for cryogenic mixed refrigerant cycles
Numerical model of a micro-structured heat exchanger for D. Gomse, S. Grohmann 2nd International Workshop on Cooling Systems for HTS Applications 09/15/2017 KIT The Research University in the Helmholtz
More informationPERFORMANCE CORRELATIONS FOR COUNTERFLOW COOLING TOWER
Jurnal Mekanikal June 2016, Vol 39, 15-26 PERFORMANCE CORRELATIONS FOR COUNTERFLOW COOLING TOWER Mohd Yusoff Senawi* Faculty of Mechanical Engineering Universiti Teknologi Malaysia 81310 UTM Johor Bahru
More informationThermo-economic analysis of regenerative heat engines
Indian Journal of Pure & Applied Physics Vol. 42, January 2004, pp 31-37 Thermo-economic analysis of regenerative heat engines Santanu Byopadhyay Energy Systems Engineering, Department of Mechanical Engineering,
More informationPARAMETRIC STUDY OF GAS TURBINE CYCLE COUPLED WITH VAPOR COMPRESSION REFRIGERATION CYCLE FOR INTAKE AIR COOLING
International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 9, September 2018, pp. 248 261, Article ID: IJMET_09_09_029 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=9&itype=9
More informationModelling of Indirect Evaporative Air Coolers
416 2nd PALENC Conference and 28th AIVC Conference on Building Low Energy Cooling and Modelling of Indirect Evaporative Air Coolers Gh. Heidarinejad Building and Housing Research Centre (BHRC), Iran M.
More informationThermal and Exergy Analysis of Counter Flow Induced Draught Cooling Tower
International Journal of Current Engineering and Technology E-ISSN 2277 4106, P-ISSN 2347 5161 2015 INPRESSCO, All Rights Reserved Available at http://inpressco.com/category/ijcet Research Article Thermal
More informationSustaining thermal power plant production in low water supply regions using cooling towers
Energy and Sustainability V 679 Sustaining thermal power plant production in low water supply regions using cooling towers H. H. Al-Kayiem 1 & M. A. W. Theeb 2 1 Mechanical Engineering Department, Universiti
More informationA NEW POLYNOMIAL BASED MODEL FOR DETERMINING COOLING TOWER EVAPORATION WATER LOSS. Aaron Powers Johnson Controls, Inc.
ASHRAE and IBPSA-USA SimBuild 2016 Building Performance Modeling Conference Salt Lake City, UT August 8-12, 2016 A NEW POLYNOMIAL BASED MODEL FOR DETERMINING COOLING TOWER EVAPORATION WATER LOSS Aaron
More informationCFD Modelling and Analysis of Different Plate Heat Exchangers
CFD Modelling and Analysis of Different Plate Heat Exchangers Ahmed Y Taha Al-Zubaydi a *, Guang Hong b and W. John Dartnall c Faculty of Engineering and Information Technology, UTS, Sydney, Australia
More informationFundamental Investigation Of Whole-Life Power Plant Performance For Enhanced Geothermal Systems
Purdue University Purdue e-pubs International Refrigeration and Air Conditioning Conference School of Mechanical Engineering 2016 Fundamental Investigation Of Whole-Life Power Plant Performance For Enhanced
More informationHeat Exchangers. Introduction. Classification of heat Exchangers
Heat Exchangers Introduction Heat Exchanger is an adiabatic steady flow device in which two flowing fluids exchange or transfer heat between themselves due to a temperature difference without losing or
More informationSolar Flat Plate Thermal Collector
Solar Flat Plate Thermal Collector 1 OBJECTIVE: Performance Study of Solar Flat Plate Thermal Collector Operation with Variation in Mass Flow Rate and Level of Radiation INTRODUCTION: Solar water heater
More information[Ansari* et al., 5(8): August, 2016] ISSN: IC Value: 3.00 Impact Factor: 4.116
IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY OPERATING PARAMETERS ACCUMULATION OF HELIUM LIQUEFICATION SYSTEM: (H.E & TURBINE) Abdul Mannan Ansari*, Vinod Sehrawat, Tarun
More informationReview on Numerical Simulation of frosting behavior on Ambient air vaporizer
Review on Numerical Simulation of frosting behavior on Ambient air vaporizer Lokesh Shivrajsingh Thakur Masters in Thermal Engineering, Mechanical Engineering Department, A.D. Patel institute of technology,
More informationApplied Thermodynamics for Marine Systems Prof. P. K. Das Department of Mechanical Engineering Indian Institute of Technology, Kharagpur
Applied Thermodynamics for Marine Systems Prof. P. K. Das Department of Mechanical Engineering Indian Institute of Technology, Kharagpur (Refer Slide Time: 00:54) Lecture - 4 Second law of Thermodynamics
More informationSimulation of Solar Air-Conditioning System with Salinity Gradient Solar Pond
Available online at www.sciencedirect.com ScienceDirect Energy Procedia 79 (2015 ) 746 751 2015 International Conference on Alternative Energy in Developing Countries and Emerging Economies Simulation
More informationPhotoetched Regenerator for Use in a High Frequency Pulse Tube
Photoetched Regenerator for Use in a High Frequency Pulse Tube W.F. Superczynski, G.F. Green Chesapeake Cryogenics, Inc. Arnold, MD 21012 ABSTRACT To produce refrigeration at 20 K in a single stage regenerative
More informationDesign of heat recovery device to elevate coefficient of performance of water cooler by circulating drain water
Design of heat recovery device to elevate coefficient of performance of water cooler by circulating drain water Ganesh Patil 1, Raj Phadatare 2 1 Student, Department of Mechanical Engineering, Maharashtra
More informationEnergy Conversion and Management
Energy Conversion and Management 51 (2010) 1298 13 Contents lists available at ScienceDirect Energy Conversion and Management journal homepage: www.elsevier.com/locate/enconman Thermal performance of cross
More informationEstimation of Boil-off-Gas BOG from Refrigerated Vessels in Liquefied Natural Gas Plant
International Journal of Engineering and Technology Volume 3 No. 1, January, 2013 Estimation of Boil-off-Gas BOG from Refrigerated Vessels in Liquefied Natural Gas Plant Wordu, A. A, Peterside, B Department
More informationIranian Journal of Hydrogen & Fuel Cell 3(2016) Iranian Journal of Hydrogen & Fuel Cell IJHFC. Journal homepage://ijhfc.irost.
DOI: http://dx.doi.org/10.22104/ijhfc.2017.430 Iranian Journal of Hydrogen & Fuel Cell IJHFC Journal homepage://ijhfc.irost.ir Inuence of unsuitable operational conditions on the transient performance
More informationMiniature PCHE-Type Recuperator with Transverse Bypass
Miniature PCHE-Type Recuperator with Transverse Bypass J. Jung, S. Jeong, G. Hwang Korea Advanced Institute of Science and Technology Daejeon, Republic of Korea ABSTRACT A high effectiveness multi-channel
More informationInternational Journal of Mechanical & Mechatronics Engineering IJMME-IJENS Vol:16 No:05 14
International Journal of Mechanical & Mechatronics Engineering IJMME-IJENS Vol:16 No:05 14 Thermal and Thermohydraulic Performance Analysis on Offset Finned Absorber Solar Air Heater Shalini Rai*,Prabha
More informationLaboratory Test of a Cylindrical Heat Storage Module with Water and Sodium Acetate Trihydrate
Downloaded from orbit.dtu.dk on: Nov 01, 2018 Laboratory Test of a Cylindrical Heat Storage Module with Water and Sodium Acetate Trihydrate Dannemand, Mark; Kong, Weiqiang; Berg, Jakob Brinkø; Furbo, Simon
More informationASSESSMENT OF R290 AS A POSSIBLE ALTERNATIVE TO R22 IN DIRECT EXPANSION SOLAR ASSISTED HEAT PUMPS
Paradeshi, L., et al.: Assesment of R290 as a Possible Alternative to R22 in S369 ASSESSMENT OF R290 AS A POSSIBLE ALTERNATIVE TO R22 IN DIRECT EXPANSION SOLAR ASSISTED HEAT PUMPS by Lokesh PARADESHI *,
More informationThermodynamic Comparison of Linde and Claude Systems for Liquefaction of Gases
Thermodynamic Comparison of Linde and Claude Systems for Liquefaction of Gases Devender Kumar *, R. S. Mishra Department Of Mechanical Engineering, Delhi Technological University, Shahabad, Delhi, India
More informationHigh-Efficiency Joule-Thomson Cryocoolers Incorporating an Ejector
1 High-Efficiency Joule-Thomson Cryocoolers Incorporating an Ejector H.S. Cao 1, S. Vanapalli 1, H.J. Holland 1, C.H. Vermeer 2, T. Tirolien 3, H.J.M. ter Brake 1 1 University of Twente, 7500 AE, Enschede,
More informationThermodynamic (energy-exergy) analysis of pre-cooled linde system
International Journal of Research in Engineering and Innovation Vol-1, Issue- (17), 1-6 International Journal of Research in Engineering and Innovation (IJREI) journal home page: http://www.ijrei.com ISSN
More informationLow-Grade Waste Heat Recovery for Power Production using an Absorption-Rankine Cycle
Purdue University Purdue e-pubs International Refrigeration and Air Conditioning Conference School of Mechanical Engineering 2010 Low-Grade Waste Heat Recovery for Power Production using an Absorption-Rankine
More informationCHAPTER 5 MASS AND ENERGY ANALYSIS OF CONTROL VOLUMES
Thermodynamics: An Engineering Approach 8th Edition in SI Units Yunus A. Ç engel, Michael A. Boles McGraw-Hill, 2015 CHAPTER 5 MASS AND ENERGY ANALYSIS OF CONTROL VOLUMES Objectives Develop the conservation
More informationENHANCED FILMWISE CONDENSATION WITH THIN POROUS COATING
Proceedings of the First Pacific Rim Thermal Engineering Conference, PRTEC March 13-17, 2016, Hawaii's Big Island, USA PRTEC-14728 ENHANCED FILMWISE CONDENSATION WITH THIN POROUS COATING Ying Zheng *,
More informationCOMPARATIVE ANALYSES OF TWO IMPROVED CO 2 COMBINED COOLING, HEATING, AND POWER SYSTEMS DRIVEN BY SOLAR ENERGY
S93 Introduction COMPARATIVE ANALYSES OF TWO IMPROVED CO 2 COMBINED COOLING, HEATING, AND POWER SYSTEMS DRIVEN BY SOLAR ENERGY by Wanjin BAI a* and Xiaoxiao XU b a School of Mechanical and Vehicle Engineering,
More informationR13. II B. Tech I Semester Regular/Supplementary Examinations, Oct/Nov THERMODYNAMICS (Com. to ME, AE, AME) Time: 3 hours Max.
SET - 1 1. a) Discuss about PMM I and PMM II b) Explain about Quasi static process. c) Show that the COP of a heat pump is greater than the COP of a refrigerator by unity. d) What is steam quality? What
More informationCarbon Monoxide Catalytic Oxidation Model
International Journal of Chemistry and Chemical Engineering. ISSN 2248-9924 Volume 3, Number 3 (2013), pp. 161-166 Research India Publications http://www.ripublication.com Carbon Monoxide Catalytic Oxidation
More informationExperimental Studies on a Solar Assisted Heat Pump Working with R22: An Exergy Point of View
Journal of Advanced Engineering Research ISSN: 2393-8447 Volume 4, Issue 2, 2017, pp94-98 Experimental Studies on a Solar Assisted Heat Pump Working with R22: An Exergy Point of View Lokesh Paradeshi 1,
More informationEXERGY LOSS ANALYSIS OF THE REGENERATOR IN A SOLAR STIRLING ENGINE
S729 EXERGY LOSS ANALYSIS OF THE REGENERATOR IN A SOLAR STIRLING ENGINE by Wenlian YE a, b, Zhe YANG a, and Yingwen LIU a* a Key Laboratory of Thermo-Fluid Science and Engineering of MOE, School of Energy
More informationPerformance Analysis of Shell and Tube Heat Exchanger Using Miscible System
American Journal of Applied Sciences 5 (5): 548-552, 2008 ISSN 1546-9239 2008 Science Publications Performance Analysis of Shell and Tube Heat Exchanger Using Miscible System 1 M. Thirumarimurugan, 2 T.Kannadasan
More informationPerformance Evaluation of an Integrated Hybrid Photovoltaic/Thermal (PV/T) Greenhouse
12 EAAS & ARF. All rights reserved Performance Evaluation of an Integrated Hybrid Photovoltaic/Thermal (PV/T) Greenhouse Shahana Parveen 1, Dr. Qamar Parvez Rana 2 Jamia Hamdard, India Shahanaparveen_amu@gmail.com
More informationDesign and thermal analysis of shell and tube type condenser
Design and thermal analysis of shell and tube type condenser Poonam Diwan Mechanical engineering dept. Vec lakhanpur, Sarguja university Ambikapur, India poonamdiwan5@gmail.com Lavish Sahu Mechanical engineering
More informationResearch Article Simulation of Sugarcane Juice Evaporation in a Falling Film Evaporator by Variation of Air Flow
Research Journal of Applied Sciences, Engineering and Technology 10(3): 322-327, 2015 DOI: 10.19026/rjaset.10.2494 ISSN: 2040-7459; e-issn: 2040-7467 2015, Maxwell Scientific Publication Corp. Submitted:
More informationCOUPLING MODEL AND SOLVING APPROACH FOR PERFORMANCE EVALUATION OF NATURAL DRAFT COUNTER-FLOW WET COOLING TOWERS
THERMAL SCIENCE: Year 2016, Vol. 20, No. 1, pp. 291-301 291 COUPLING MODEL AND SOLVING APPROACH FOR PERFORMANCE EVALUATION OF NATURAL DRAFT COUNTER-FLOW WET COOLING TOWERS by Wei WANG *, Deliang ZENG,
More informationPAPER-I (Conventional)
1. a. PAPER-I (Conventional) 10 kg of pure ice at 10 ºC is separated from 6 kg of pure water at +10 O C in an adiabatic chamber using a thin adiabatic membrane. Upon rupture of the membrane, ice and water
More informationK.S. Rawat 1, H. Khulve 2, A.K. Pratihar 3 1,3 Department of Mechanical Engineering, GBPUAT, Pantnagar , India
Thermodynamic Analysis of Combined ORC-VCR System Using Low Grade Thermal Energy K.S. Rawat 1, H. Khulve 2, A.K. Pratihar 3 1,3 Department of Mechanical Engineering, GBPUAT, Pantnagar-263145, India 2 Department
More informationEvaluation of Thermal Performance of Low Cost Plastic Collectors for Rural Applications
Evaluation of hermal Performance of Low Cost Plastic ors for Rural Applications R. S. Mishra Department of Mechanical Engineering, Delhi echnological University, New Delhi, India Article Info Article history:
More informationComputational Modeling of Counter Flow Heat Exchanger for LMTD Analysis
Computational Modeling of Counter Flow Heat Exchanger for LMTD Analysis Shuvam Mohanty 1, Shofique Uddin Ahmed 2 1, 2 Student, M. Tech, Department Of Mechanical Engineering, Amity University Gurgaon, Haryana
More informationModule 05 Lecture 35 : Low temperature process design Key words: Refrigeration system
Refrigeration System Module 05 Lecture 35 : Low temperature process design Key words: Refrigeration system A refrigerator is simply a heat pump where heat is rejected to atmosphere( the sink). Fig.41.3(lecture
More informationThermo-Fluid Modeling of a Full Scale Liquid Hydrogen Storage System with Integrated Refrigeration
Paper #006 478 1 Thermo-Fluid Modeling of a Full Scale Liquid Hydrogen Storage System with Integrated Refrigeration J. H. Baik 1, W. U. Notardonato 2, S. Karng 3, S. Kim 3, and I. Oh 4 1 Florida Solar
More informationBattery thermal models for hybrid vehicle simulations
Journal of Power Sources 110 (2002) 377 382 Battery thermal models for hybrid vehicle simulations Ahmad A. Pesaran National Renewable Energy Laboratory, 1617 Cole Blvd, Golden, CO 80401, USA Abstract This
More informationEffect of Tower Area Change on the Potential of Solar Tower
The nd Joint International Conference on Sustainable Energy and Environment (SEE 006) B-09 (O) - November 006, Bangkok, Thailand Effect of Tower rea Change on the Potential of Solar Tower tit Koonsrisuk
More informationRESIDUAL STRESS AND DISTORTION ANALYSIS IN LASER BEAM WELDING PROCESSES
Ind. J. Sci. Res. and Tech. 015 3():0-5/Kanthi ISSN:-31-96 (Online) RESIDUAL STRESS AND DISTORTION ANALYSIS IN LASER BEAM WELDING PROCESSES Rajesh Goud Kanthi School of Mechanical Engineering,CEST, Fiji
More informationOn the use of heat pumps in total site heat integration
Computers and Chemical Engineering 27 (2003) 1707/1719 www.elsevier.com/locate/compchemeng On the use of heat pumps in total site heat integration Miguel J. Bagajewicz *, Andrés F. Barbaro Department of
More informationBrazed aluminium heat exchangers (BAHXs), also referred to
Brazed aluminium heat exchangers (BAHXs), also referred to as plate fin heat exchangers, are at the heart of many of the processes used for the liquefaction of natural gas. They are deployed across the
More informationNumerical and analytical analysis of groundwater influence on the pile ground heat exchanger with cast-in spiral coils
Available online at www.sciencedirect.com ScienceDirect Energy Procedia 61 (2014 ) 1784 1788 The 6 th International Conference on Applied Energy ICAE2014 Numerical and analytical analysis of groundwater
More informationTheoretical analysis of an integrated thermoelectric-absorption cooling system
Theoretical analysis of an integrated thermoelectric-absorption cooling system R. Boukhanouf (corresponding author) and A. Supasuteekul School of the Built Environment University of Nottingham, Nottingham,
More informationExternal and Internal Irreversibility
External and Internal Irreversibility Heat Engine as an Example Arnab Sarkar and S S Mondal The article attempts to clarify the meaning of internal and external irreversibility using the example of a heat
More informationCHAPTER 1 BASIC CONCEPTS
GTU Paper Analysis CHAPTER 1 BASIC CONCEPTS Sr. No. Questions Jan 15 Jun 15 Dec 15 May 16 Jan 17 Jun 17 Nov 17 May 18 Differentiate between the followings; 1) Intensive properties and extensive properties,
More informationAvailable online at ScienceDirect. Procedia Engineering 152 (2016 )
Available online at www.sciencedirect.com ScienceDirect Procedia Engineering 152 (2016 ) 209 218 International Conference on Oil and Gas Engineering, OGE-2016 About LNG energy utilization efficiency estimation
More informationAN EXPERIMENTAL STUDY AND NUMERICAL SIMULATION OF TWO-PHASE FLOW OF CRYOGENIC FLUIDS THROUGH MICRO-CHANNEL HEAT EXCHANGER
AN EXPERIMENTAL STUDY AND NUMERICAL SIMULATION OF TWO-PHASE FLOW OF CRYOGENIC FLUIDS THROUGH MICRO-CHANNEL HEAT EXCHANGER W. W. Yuen and I. C. Hsu Department of Mechanical Engineering University of California,
More informationResearch on a Magnetic Refrigeration Cycle for Hydrogen Liquefaction
Research on a Magnetic Refrigeration Cycle for Hydrogen Liquefaction T. Utaki 1, K. Kamiya 2, T. Nakagawa 1, T. A. Yamamoto 1 and T. Numazawa 2 1 Graduate school of Engineering, Osaka University Osaka,
More informationValidation of various cryogenics systems using exergy analysis
International Journal of Research in Engineering and Innovation Vol-2, Issue-1 (2018), 97-104 International Journal of Research in Engineering and Innovation (IJREI) journal home page: http://www.ijrei.com
More informationEnhancement on the Performance of Refrigeration System Using the Nano-Refrigerant
Journal of Energy and Power Engineering 11 (2017) 237-243 doi: 10.17265/1934-8975/2017.04.004 D DAVID PUBLISHING Enhancement on the Performance of Refrigeration System Using the Nano-Refrigerant Qasim
More informationEasyChair Preprint. Resolving the Non-Productive Periods of Solar Chimney by Integrating with Waste-to-Energy Plant
EasyChair Preprint 159 Resolving the Non-Productive Periods of Solar Chimney by Integrating with Waste-to-Energy Plant Ali Habibollahzade, Ehsan Houshfar, Amir Mohammad Behzadi, Ehsan Gholamian and Mehdi
More informationOptimal operation of simple refrigeration cycles Part I: Degrees of freedom and optimality of sub-cooling
Optimal operation of simple refrigeration cycles Part I: Degrees of freedom and optimality of sub-cooling Jørgen Bauck Jensen and Sigurd Skogestad Department of Chemical Engineering Norwegian University
More informationDESIGN OF LIQUID COOLING FOR HIGH HEAT DISSIPATION ELECTRONIC BOARDS USING CFD
DESIGN OF LIQUID COOLING FOR HIGH HEAT DISSIPATION ELECTRONIC BOARDS USING CFD PANKAJ JIVAN PATEL 1, KAILAS TUKARAM PATIL 2, MANKALAL HIRAJI PATIL 3 1 Student, Department of Mechanical Engineering, P.S.G.V.P.
More informationPerformance Analysis of An Indirect Evaporative Cooling System using M Cycle Devang S. Patel 1 Hardik M.Patel 2
IJSRD - International Journal for Scientific Research & Development Vol. 3, Issue 05, 2015 ISSN (online): 2321-0613 Performance Analysis of An Indirect Evaporative Cooling System using M Cycle Devang S.
More informationThermal Analysis of a Mobile Hot Cell Cask
Thermal Analysis of a Mobile Hot Cell Cask Jay Kalinani 1, Arvind Kumar R 2 P.G. Student, Department of Physics, MS Ramaiah University of Applied Sciences, Bangalore, Karnataka, India 1 U.G. Student, Department
More informationHEAT TRANSER AND EXERGY ANALYSIS OF A DOUBLE PIPE HEAT EXCHANGER
HEAT TRANSER AND EXERGY ANALYSIS OF A DOUBLE PIPE HEAT EXCHANGER Ch. Praveen Kumar 1, L.Narsinga Rao 2, M.Raghu 3, Y.Pavan Kumar 4 1,2.3,4 M.Tech Dept. of Mechanical Engineering, V.R.Siddhartha Engineering
More informationENERGY AND EXERGY ANALYSIS OF HEAT PUMP USING R744/R32 REFRIGERANT MIXTURE
THERMAL SCIENCE, Year 2014, Vol. 18, No. 5, pp. 1649-1654 1649 ENERGY AND EXERGY ANALYSIS OF HEAT PUMP USING R744/R32 REFRIGERANT MIXTURE by Fang WANG, Xiao-Wei FAN, Jie CHEN, and Zhi-Wei LIAN School of
More informationThermodynamics: An Engineering Approach, 6 th Edition Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2008
Thermodynamics: An Engineering Approach, 6 th Edition Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2008 Chapter 5 MASS AND ENERGY ANALYSIS OF CONTROL VOLUMES SUMMARY 1 CONSERVATION OF MASS Conservation
More informationDESIGN OF VAPOUR ABSORPTION REFRIGERATION SYSTEM OF 1.5TR CAPACITY BY WASTE HEAT RECOVERY PROCESS
Volume 115 No. 7 2017, 613-619 ISSN: 1311-8080 (printed version); ISSN: 1314-3395 (on-line version) url: http://www.ijpam.eu ijpam.eu DESIGN OF VAPOUR ABSORPTION REFRIGERATION SYSTEM OF 1.5TR CAPACITY
More informationPerformance Evaluation of Solar Assisted Heat Pump Water Heating System
IOSR Journal of Engineering (IOSRJEN) e-issn: 50-301, p-issn: 78-8719 Vol. 3, Issue 4 (April. 013), V PP 1-17 Performance Evaluation of Solar Assisted Heat Pump Water Heating System Kokila. R.N 1, Rajakumar.S
More informationA novel CO 2 -capturing natural gas combined cycle with LNG cold energy utilization
Available online at www.sciencedirect.com ScienceDirect Energy Procedia 61 (2014 ) 899 903 The 6 th International Conference on Applied Energy ICAE2014 A novel CO 2 -capturing natural gas combined cycle
More informationBoiler Efficiency Testing. To understand the operation of a fire tube boiler To determine the operating efficiency of the boiler
Boiler Efficiency Testing Objectives: To understand the operation of a fire tube boiler To determine the operating efficiency of the boiler Theory Most industrial processes require heating. This is usually
More informationEnhancement of Heat Transfer in Concentric Tube Heat Exchanger using Water Based Nano Fluid ( )
Volume: 03 Issue: 0 May-201 www.irjet.net p-issn: 239-0072 Enhancement of Heat Transfer in Concentric Tube Heat Exchanger using Water Based Nano Fluid ( ) Dhiraj Valekar 1, Shubham Wagh 2, Umakant Tavhare
More informationHeat Integration Across Plants Considering Distance Factor
A publication of CHEMICAL ENGINEERING TRANSACTIONS VOL. 35, 2013 Guest Editors: Petar Varbanov, Jiří Klemeš, Panos Seferlis, Athanasios I. Papadopoulos, Spyros Voutetakis Copyright 2013, AIDIC Servizi
More informationNanoparticles Enhanced Phase Change Material (NPCM) as Heat Storage in Solar Still Application for Productivity Enhancement
Available online at www.sciencedirect.com ScienceDirect Energy Procedia 141 (2017) 45 49 www.elsevier.com/locate/procedia 4th International Conference on Power and Energy Systems Engineering, CPESE 2017,
More informationBrazed Aluminum Heat Exchangers (BAHX) for Optimisation of Natural Gas Liquefaction Processes. Gastech 2017
Brazed Aluminum Heat Exchangers (BAHX) for Optimisation of Natural Gas Liquefaction Processes Authors: Doug Ducote / Paul Shields Introduction Gastech 2017 Brazed aluminum heat exchangers (BAHX), also
More informationSIMULATION AND ANALYSIS ON THE EFFECTS OF HEAT EXCHANGERS IN A LIQUID AIR ENERGY STORAGE SYSTEM
Proceedings of the Asian Conference on Thermal Sciences 207, st ACTS March 26-0, 207, Jeju Island, Korea ACTS-P00060 SIMULATION AND ANALYSIS ON THE EFFECTS OF HEAT EXCHANGERS IN A LIQUID AIR ENERGY STORAGE
More informationTHERMAL AND ELECTRICAL PERFORMANCES OF A NEW KIND AIR COOLED PHOTOVOLTAIC THERMAL SYSTEM FOR BUILDING APPLICATION
THERMAL AND ELECTRICAL PERFORMANCES OF A NEW KIND AIR COOLED PHOTOVOLTAIC THERMAL SYSTEM FOR BUILDING APPLICATION R.S. Adhikari, F. Butera, P. Caputo, P. Oliaro and N. Aste Department of Building Environment
More informationRefrigerant Expanders Improve LNG Liquefaction Process
Refrigerant Expanders Improve LNG Liquefaction Process Chen-Hwa Chiu TEXACO Bellaire, TX 77401, USA Hans E. Kimmel EBARA INTERNATIONAL CORPORATION Sparks, Nevada 89434, USA In conventional natural gas
More informationLinde and Claude System Second Law Comparison for Liquefaction of Air
Linde and Claude System Second Law Comparison for Liquefaction of Air Devender Kumar *, R.S Mishra Department Of Mechanical Engineering, Delhi Technological University, Shahabad, Delhi, India Article Info
More informationExperimental Tests on Sodium Thermosyphons
Joint 18th IHPC and 12th IHPS, Jeju, Korea, June 12-16, 2016 Experimental Tests on Sodium Thermosyphons Tiago W. Uhlmann 1, Marcia B. H. Mantelli 1*, Miriam Manzoni 2, Marco Marengo 2, Per Eskilson 3 1
More informationInternational Journal of Advance Engineering and Research Development. SOLIDIFICATION SIMULATION OF Al 6061 CASTING IN 2-D GREEN SAND MOULD
Scientific Journal of Impact Factor(SJIF): 3.134 International Journal of Advance Engineering and Research Development Volume,Issue 7, July -1 e-issn(o): 348-447 p-issn(p): 348-646 SOLIDIFICATION SIMULATION
More informationCFD ANALYSIS OF CONVECTIVE FLOW IN A SOLAR DOMESTIC HOT WATER STORAGE TANK
International Journal of Scientific & Engineering Research Volume 4, Issue 1, January-2013 1 CFD ANALYSIS OF CONVECTIVE FLOW IN A SOLAR DOMESTIC HOT WATER STORAGE TANK Mr. Mainak Bhaumik M.E. (Thermal
More informationWastewater Pretreatment by Normal Freezing Cool Thermal Storage Process with Convective Heat Transfer Mechanism
Tamkang Journal of Science and Engineering, Vol. 14, No. 2, pp. 115 122 (2011) 115 Wastewater Pretreatment by Normal Freezing Cool Thermal Storage Process with Convective Heat Transfer Mechanism Chao-Ching
More informationGround Coupled Heat Pump Design for Tafila Climate
J. Appl. Res. Ind. Eng. Vol. 4, No. 3 (2017)180 184 Journal of Applied Research on Industrial Engineering www.journal-aprie.com Ground Coupled Heat Pump Design for Tafila Climate Emran M. Ataykah Department
More informationPERFORMANCE ENHANCEMENT OF A MINIATURE STIRLING CRYOCOOLER WITH A MULTI MESH REGENERATOR DESIGN
Journal of Engineering Science and Technology Vol. 12, No. 6 (2017) 1514-1524 School of Engineering, Taylor s University PERFORMANCE ENHANCEMENT OF A MINIATURE STIRLING CRYOCOOLER WITH A MULTI MESH REGENERATOR
More informationDESIGN OF HEAT EXCHANGER FOR EXHAUST HEAT RECOVERY OF A SINGLE CYLINDER COMPRESSION IGNITION ENGINE
Journal of Engineering Science and Technology Vol. 13, No. 7 (2018) 2153-2165 School of Engineering, Taylor s University DESIGN OF HEAT EXCHANGER FOR EXHAUST HEAT RECOVERY OF A SINGLE CYLINDER COMPRESSION
More informationThe Performance of Compression-absorption Heat Pump System Using Low-temperature Geothermal Tail Water
Proceedings World Geothermal Congress 01 Melbourne, Australia, 19- April 01 The Performance of Compression-absorption Heat Pump System Using Low-temperature Geothermal Tail Water Yulie Gong, Chao Luo,
More informationAREN 2110: Thermodynamics Spring 2010 Homework 7: Due Friday, March 12, 6 PM
AREN 2110: Thermodynamics Spring 2010 Homework 7: Due Friday, March 12, 6 PM 1. Answer the following by circling the BEST answer. 1) The boundary work associated with a constant volume process is always
More informationOperation of the Levitated Dipole Experiment Floating Coil
> THA11P002 < 1 Operation of the Levitated Dipole Experiment Floating Coil A. Zhukovsky, D. Garnier Abstract The Levitated Dipole Experiment (LDX) is an innovative facility to study plasma confinement
More informationComparison of combined heat and power systems using an organic Rankine cycle and a low-temperature heat source
*Corresponding author. mohammed.khennich@ usherbrooke.ca Comparison of combined heat and power systems using an organic Rankine cycle and a low-temperature heat source... Mohammed Khennich *, Nicolas Galanis
More informationModelling of multistream heat exchanger for natural gas liquefaction
Modelling of multistream heat exchanger for natural gas liquefaction Anita Dal Porto Relatore: Fabrizio Bezzo Correlatore: Maarten Nauta 5/12/2014 Introduction green energy source, with market in expansion.
More information- 2 - SME Q1. (a) Briefly explain how the following methods used in a gas-turbine power plant increase the thermal efficiency:
- 2 - Q1. (a) Briefly explain how the following methods used in a gas-turbine power plant increase the thermal efficiency: i) regenerator ii) intercooling between compressors (6 marks) (b) Air enters a
More information