Trex Wood-Polymer Composite Lumber
|
|
- Willis Robertson
- 6 years ago
- Views:
Transcription
1 Evaluation Report CCMC R MASTERFORMAT Issued Re-evaluated Revised Re-evaluation due Re-Evaluation in Progress Trex Wood-Polymer Composite Lumber 1. Opinion It is the opinion of the Canadian Construction Materials Centre (CCMC) that Trex Wood-Polymer Composite Lumber when used as both exterior decking and as stair treads in accordance with the conditions and limitations stated in Section 3 of this Report, complies with the National Building Code of Canada (NBC) 2005: Clause (1)(b) Division A as an alternative solution that achieves at least the minimum level of performance required by Division B in the areas defined by the objectives and functional statements attributed to the following applicable acceptable solutions: Article , Subfloor Thickness or Rating, Subsection , Specified Loads, and Article , Deflections. This opinion is based on CCMC s evaluation of the technical evidence in Section 4.1 provided by the Report Holder. Ruling No (13125-R) authorizing the use of this product in Ontario, subject to the terms and conditions contained in the Ruling, was made by the Minister of Municipal Affairs and Housing on July 20, 2004 (revised on December 8, 2008) pursuant to s.29 of the Building Code Act, 1992 (see Ruling for terms and conditions). This Ruling is subject to periodic revisions and updates. 2. Description Trex Wood-Polymer Composite Lumber is a wood thermoplastic composite made primarily from equal parts of reclaimed hardwood sawdust and reclaimed/recycled polyethylene. The composite product is manufactured through a continuous extrusion process in planks of solid cross-section. The planks are manufactured in nominal dimensions of: 32 mm x 140 mm, 38 mm x 89 mm, 38 mm x 140 mm and 38 mm x 184 mm. The planks are available in 3.66-m lengths. The 38-mm x 89-mm plank is also available in 4.88-m lengths, whereas the 32-mm x 140-mm and 38-mm x 140-mm planks are also available in 6.10-m lengths. Trex Wood-Polymer Composite Lumber is intended to be used as exterior decking installed over traditional structural wood framing (Figure 1)
2 Figure 1. Trex Wood-Polymer Composite Lumber 3. Conditions and Limitations CCMC s compliance opinion in Section 1 is contingent upon Trex Wood-Polymer Composite Lumber being used in accordance with the conditions and limitations set out below. The product may be used as exterior decking and as stair treads in combustible construction for light-duty applications, such as in residential occupancies, falling within the scope of Part 9 of Division B of the NBC 2005, when it is installed in conjunction with traditional structural wood framing designed to carry the applicable loads. The product must be installed in accordance with the manufacturer s usage guidelines for the Canadian market, and in accordance with the following limitations: The 32-mm x 140-mm and 38-mm x 89-mm planks must be installed with supports spaced no greater than 400 mm on centre (o.c.), and the 38-mm x 140-mm and 38-mm x 184-mm planks must be installed with supports spaced no greater than 500 mm o.c. Each plank must be supported by at least 3 supports. Trex Wood-Polymer Composite Lumber must be fastened to the wood joists with fasteners conforming to Article of the NBC The fasteners must have a corrosion protection coating (1) or be made of stainless steel. The planks must be fastened with at least two fasteners per support, and the fasteners must be at least 76 mm long. (1) As of January 2004, pressure-treated lumber requires specific hot-dipped galvanized fasteners for satisfactory performance
3 Trex Wood-Polymer Composite Lumber must be gapped end-to-end, based on the length of the plank and the temperature at installation. The end-to-end gapping must be 5 mm for installations below 15 C and 3 mm for installations above 15 C. The width-to-width gapping must be 6 mm for installations above 5 C and 10 mm for installations below 5 C. Trex Wood-Polymer Composite Lumber may be installed by a knowledgeable person familiar with the product installation guide. The Trex Wood-Polymer Composite Lumber product label or packaging, where possible, must be identified with the following information: manufacturer s name or logo; and the phrase CCMC R. 4. Technical Evidence CCMC s Technical Guide for Wood Thermoplastic Composite Lumber Used as Exterior Decking (Solid Cross-Section) sets out the nature of the technical evidence required by CCMC to enable it to evaluate a product as an acceptable or alternative solution in compliance with the NBC The Report Holder has submitted test results for CCMC s evaluation. Testing was conducted at an independent laboratory recognized by CCMC. The corresponding test results for Trex Wood-Polymer Composite Lumber are summarized below. 4.1 NBC 2005 Compliance Data for Trex Wood-Polymer Composite Lumber on which CCMC Based its Opinion in Section 1 Table 4.1. Basic Physical and Mechanical Properties of Trex Wood-Polymer Composite Lumber Property Unit Requirement Result (1)(2) Dimensional Change Coefficient of linear expansion (thermal): longitudinal cross-sectional Coefficient of linear expansion (swelling): % oven-dry to vacuum pressure soak Strength and Stiffness Modulus of elasticity (MOE): span-to-depth ratio within 18 to 21 Modulus of rupture (MOR): span-to-depth ratio within 18 to 21 cm/cm/ C < 2 x 10-5 < 0.5, by 80% of specimens (3) (3) MPa > (s.d. = 121) MPa > (s.d. = 0.92) Impact resistance (Izod impact, notched): J/m > (4) Hardness (11.28-mm-diameter ball): kn > < 25 for creep 49.1 (5) Creep, recovery and load duration: % > 75 for recovery 68.7 (5) No failure Passed Strength and Stiffness After Aging Weathering: impact resistance % Accelerated aging: MOE and MOR % > 75 of nonweathered value > 50 of non-aged value (MOE) 71 (MOR) - 3 -
4 Table 4.1. Basic Physical and Mechanical Properties of Trex Wood-Polymer Composite Lumber (cont d) Property Unit Requirement Result (1)(2) Nail withdrawal strength Lateral nail strength Flame-spread: Smoke development Fastener Holding Capacity N N Flame-Spread Rating - > 600 > 720 < 200 Report 761 (s.d. = 35) 518 (6) (s.d. = 100) 120 > 500 (1) Average test results of six specimens, except for the Creep, recovery and load duration results, which are from three specimens. (2) Test results were obtained to classify the product and are not intended to be used as engineering design properties. (3) Deemed acceptable based on the manufacturer s gapping installation instructions. (4) Deemed acceptable based on the full-scale structural impact test results. (5) Deemed acceptable for decking application based on other test results. The product creep (deformation under constant load) will be greater than that of lumber planks. (6) Deemed acceptable based on the full-scale structural test results and fastening detail test results. Table 4.2. Performance Under both Concentrated Static Loads and Impact Loads Property Concentrated load: decking at 50 C decking at 20 C decking at 35 C Impact load: decking at 50 C decking at 35 C (1) (2) (3) (4) Minimum Requirement Result (1) Maximum 0.89-kN Load Minimum of 1.78 kn Following Impact Load of 102 N m Maximum 0.89-kN Load Following Impact Load of 102 N m of 1.78 kn Following Impact Load of 102 N m 0.89-kN Load 5.28 (2) 2.71 (3) kN Load Following Impact Load of 102 N m (4) Test results for 38-mm x 140-mm planks with supports at 500 mm o.c. Although 5.28 mm is greater than the 2.4-mm requirement, it was deemed acceptable for material at 50 C. However, the deflection of the decking will be slightly higher than that of wood-based panels conforming to the NBC 2005 subfloor requirements at this high temperature. Deemed acceptable for the intended use, as the 0.31-mm deflection above the 2.4-mm requirement was not considered significant. Although 5.92 mm is greater than the 2.4-mm requirement, the deflection of the plank increased by less than 1 mm after it was exposed to impact loads, thus it was deemed acceptable for material at 50 C - 4 -
5 Table 4.3. Durability, Decay, Termite and Slip Resistance Property Requirement Result Mean percentage loss in MOE and MOR after UV-exposure and accelerated aging must be less Passed than or equal to spruce lumber Durability: Modulus of elasticity (MOE) Modulus of rupture (MOR) Decay resistance: % loss in weight Compressive strength Termite Resistance: Slip resistance: (longitudinal) dry condition wet condition Mean percentage loss in weight and compressive strength after exposure to decay-causing fungi must be equal to or better than spruce heartwood Rating must be equal to or better than preservative-treated wood conforming to CSA 80.1-M97 > 0.5 ASTM D Passed Passed 0.23 (1) 0.58 (1) The dry condition value does not meet the minimum required value and may not meet occupant expectations. The manufacturer may be contacted for further information. Table 4.4. Performance Under Concentrated Static Load Stair Tread Property Concentrated load: stair tread stair tread nosing with riser (1) (2) (3) (4) Minimum 5 (2) Requirement Result (1) Maximum 1-kN Applied 1-kN (4) 5 (3) 10 Test results are for 50 C and 80% RH test condition for stair stringers spaced at 305 mm o.c. Three specimens were tested for each test. Applied through a 75-mm-diameter disk positioned at the centre line of the plank and mid-way between stringers. Applied through a 38-mm-diameter disk positioned along the outside edge of the nosing of the plank and mid- way between stringers. Although the deflection is slightly higher than the allowed limit, the applied ultimate load was 40% higher than the minimum required ultimate load, and so this deflection was deemed acceptable
6 Report Holder Plants (1) Trex Company, Inc. 245 Capitol Lane Winchester, Virginia USA Tel.: (540) Fax: (540) Shawnee Drive Winchester, Virginia USA East Newlands Drive Fernley, Nevada USA (1) Report only valid for products manufactured at listed plants herein. This Report is issued by the Canadian Construction Materials Centre, a program of the Institute for Research in Construction at the National Research Council of Canada. The Report must be read in the context of the entire CCMC Registry of Product Evaluations, including, without limitation, the introduction therein which sets out important information concerning the interpretation and use of CCMC Evaluation Reports. Readers must confirm that the Report is current and has not been withdrawn or superseded by a later issue. Please refer to or contact the Canadian Construction Materials Centre, Institute for Research in Construction, National Research Council of Canada, 1200 Montreal Road, Ottawa, Ontario, K1A 0R6. Telephone (613) Fax (613) NRC has evaluated the material, product, system or service described herein only for those characteristics stated herein. The information and opinions in this Report are directed to those who have the appropriate degree of experience to use and apply its contents. This Report is provided without representation, warranty, or guarantee of any kind, expressed, or implied, and the National Research Council of Canada (NRC) provides no endorsement for any evaluated material, product, system or service described herein. NRC accepts no responsibility whatsoever arising in any way from any and all use and reliance on the information contained in this Report. NRC is not undertaking to render professional or other services on behalf of any person or entity not to perform any duty owed by any person or entity to another person or entity
Evaluation Report CCMC R Trex Transcend Decking
Evaluation Report CCMC 13125-R Trex Transcend Decking MasterFormat: 06 73 14.01 Evaluation issued: 2003-06-24 Re-evaluated: 2017-04-13 Re-evaluation due: 2019-06-24 1. Opinion It is the opinion of the
More informationPower JoIst ADI-40, ADI-60, ADI-80 I-joists
Evaluation Report CCMC 13053-R MASTERFORMAT DIVISION 06 17 33.01 Issued 2002-03-06 Re-evaluated 2008-09-19 Re-evaluation due 2011-03-06 Power JoIst ADI-40, ADI-60, ADI-80 I-joists 1. Opinion It is the
More informationMineral-Fibre Thermal Insulation for Buildings
Preface MASTERFORMAT 07 21 13.19 REVISED DATE 2011-06-22 Mineral-Fibre Thermal Insulation for Buildings Scope These Evaluation Listings apply to mineral-fibre thermal insulation in the form of faced and
More informationEvaluation Report CCMC R LP SolidStart LVL
Evaluation Report CCMC 11518-R LP SolidStart LVL MASTERFORMAT: 06 17 10.01 Evaluation issued: 1987-06-03 Revised: 2015-01-13 Re-evaluation due: 2018-04-27 1. Opinion It is the opinion of the Canadian Construction
More informationEvaluation Listing CCMC L Nordic X-Lam
CONSTRUCTION Evaluation Listing CCMC 3654-L Nordic X-Lam Evaluation Issued: 203-2-24 Re-evaluation due: 206-2-24 Preface: Masterformat 06 9 00.02, Cross Laminated Timber (CLT) Panels (Standardized) Preface
More informationEvaluation Listing CCMC L Boreal Lavender and Boreal Nature
Evaluation Listing CCMC 14025-L Boreal Lavender and Boreal Nature MasterFormat: 07 21 19.02 Evaluation issued: 2015-10-16 Revised: 2016-10-05 Re-evaluation due: 2018-10-16 1. Evaluation The product conforms
More informationDIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PLASTICS SECTION: PLASTIC DECKING REPORT HOLDER:
0 ICC-ES Report ICC-ES (800) 423-6587 (562) 699-0543 www.icc-es.org 000 Most Widely Accepted and Trusted ESR-3168 Reissued 02/2016 This report is subject to renewal 02/2017. DIVISION: 06 00 00 WOOD, PLASTICS
More informationESR-1461 Reissued February 1, 2014 This report is subject to renewal March 1, 2015.
ICC-ES Evaluation Report www.icc-es.org (800) 43-6587 (56) 699-0543 ESR-46 Reissued February, 04 This report is subject to renewal March, 05. A Subsidiary of the International Code Council DIVISION: 06
More informationRB 133 RIM BOARD PRODUCT STANDARD. Version 2.3
RB 133 RIM BOARD PRODUCT STANDARD Version 2.3 October 1, 2013 No part of this publication may be reproduced or used in any form or by any means without the written consent of Timberco Inc. dba TECO. Inquiries
More informationWood Solutions Fair, 2014, Toronto
Overview of Changes to CSA O86-2014 & Structural Design Provisions for Mid-Rise in OBC Wood Solutions Fair, 2014, Toronto Jasmine Wang, Ph.D., P.Eng. Canadian Wood Council Copyright Materials This presentation
More informationDIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PLASTICS SECTION: PLASTIC DECKING REPORT HOLDER:
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3771 Reissued 11/2017 This report is subject to renewal 11/2018. DIVISION: 06 00
More informationDecember 1, 2014 PARTIES INTERESTED IN STRUCTURAL WOOD-BASED PRODUCTS
December 1, 2014 TO: PARTIES INTERESTED IN STRUCTURAL WOOD-BASED PRODUCTS SUBJECT: Proposed Revision to the ICC-ES Acceptance Criteria for Structural Wood-Based Products, Subject AC47-1214-R2-2 (JF/PC)
More informationCCMC MgO Board Advisory
CCMC MgO Board Advisory July 2017 Dear Building Officials, CCMC was recently made aware of premature failures in other countries of some magnesium oxide (MgO) boards. Due to the increased use of MgO boards
More informationDIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: PLASTIC RAILINGS SECTION: STRUCTURAL PLASTICS REPORT HOLDER:
0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-3947 Reissued 09/2017 This report is subject to renewal 09/2018. DIVISION: 06 00
More informationDIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PLASTICS SECTION: PLASTIC DECKING REPORT HOLDER:
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2497 Reissued 01/2018 This report is subject to renewal 01/2019. DIVISION: 06 00
More informationDIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: NAILS REPORT HOLDER: PASLODE, AN ILLINOIS TOOL WORKS COMPANY
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3071 Reissued 12/2017 This report is subject to renewal 12/2018. DIVISION: 06 00
More informationFACT SHEET #2 DECK INFORMATION
Borough of Doylestown Building and Zoning Department 57 West Court Street, Doylestown, PA 18901 215.345.4140 FACT SHEET #2 DECK INFORMATION BACKGROUND The provisions of the PAUCC. ICC Property Maintenance
More informationCode Compliance Research Report CCRR-0101
Code Compliance Research Report CCRR-0101 Issue Date: 07-31-2017 Renewal Date: 05-19-2018 DIVISION: 06 00 00 WOOD, PLASTICS, AND COMPOSITES Section: 06 50 00 Structural Plastics Section: 06 53 00 Plastic
More informationPRP-108 Performance Standards and Policies for Structural-Use Panels
A P A S T A N D A R D PRP-108 Performance Standards and Policies for Structural-Use Panels Published by APA The Engineered Wood Association February 1994 A P A The Engineered Wood Association 1997 APA
More informationPOST FRAME BUILDING STANDARDS
CASS COUNTY, MISSOURI BUILDING CODES, ENVIRONMENTAL HEALTH AND ZONING DEPARTMENT 30508 S. West Outer Road, Harrisonville, MO 64701 P- (816) 380-8134 F- (816) 380-8130 POST FRAME BUILDING STANDARDS 201.3
More informationHILLSBOROUGH TOWNSHIP CODE ENFORCEMENT
HILLSBOROUGH TOWNSHIP CODE ENFORCEMENT SAMPLE GUIDE FOR RESIDENTIAL DECKS revised 7 16 Call before you dig! 1 800 272 1000 New Jersey One Call. Utility Mark Out. THIS GENERIC GUIDE IS NOT ALL INCLUSIVE
More informationATI Evaluation Service A Division of Architectural Testing Certification Services
ATI Evaluation Service A Division of Architectural Testing Certification Services Subject to Renewal: 08/09/2014 Issued: 08/09/2013 Visit www.ati-es.com for current status Revised: 08/12/2013 Page 1 of
More informationMurphy Laminated Veneer Lumber Murphy Engineered Wood Division Revised May 30, 2013
Murphy Laminated Veneer Lumber PR-L283 Murphy Engineered Wood Division Revised May 30, 2013 Product: 2250F b -1.5E, 2600F b -1.7E, 2750F b -1.8E, 2850F b -1.9E, 2950F b -2.0E, 3100F b -2.0E, and 3100F
More informationCode Compliance Research Report CCRR-0185
Code Compliance Research Report CCRR-0185 Issue Date: 12-09-2016 Renewal Date: 12-10-2017 Revision Date: 04-20-2017 DIVISION: 06 00 00 WOOD, PLASTICS, AND COMPOSITES Section: 06 50 00 Structural Plastics
More informationDIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL ROOF PANELS SECTION: METAL WALL PANELS REPORT HOLDER:
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 4 6587 (562) 699 0543 www.icc es.org ESR 3152 Reissued 08/2017 This report is subject to renewal 08/2018. DIVISION: 07 00 00
More informationRESIDENTIAL WOOD DECK CONSTRUCTION GUIDE
RESIDENTIAL WOOD DECK CONSTRUCTION GUIDE Based on The 2009 Michigan Residential Code Revised September 25, 2014 Wood Deck Construction in accordance with this guide is acceptable in the following Michigan
More informationREPORT HOLDER: ispan SYSTEMS LP 70 BRENTWOOD DRIVE PRINCETON, ONTARIO N0J 1V0 CANADA EVALUATION SUBJECT:
0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 2-6587 (562) 699-05 www.icc-es.org ESR-787 Issued 07/2017 This report is subject to renewal 07/2018. DIVISION: 05 00 00 METALS
More informationApproved Manufacturing Locations. 181 Random Drive 181 Random Drive 420 W Franklin Rd New London, NC New London, NC Meridian, ID 83642
Pei Evaluation Service is an accredited ISO Standard 17065 Product Certifier, accredited by the IAS. This Product Evaluation Report represents a product that Pei ES has Evaluated and this product has a
More informationDIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: SHOP FABRICATED WOOD TRUSSES REPORT HOLDER: BARRETTE STRUCTURAL DISTRIBUTION, INC.
0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 43 6587 (56) 699 0543 www.icc es.org ESR 999 Reissued 0/07 This report is subject to renewal 0/08. DIVISION: 06 00 00 WOOD, PLASTICS AND
More informationBUILDING BULLETIN One and Two Family Dwellings Decks and Residential Access Ramps
BUILDING BULLETIN One and Two Family Dwellings Decks and Residential Access Ramps City of Virginia Beach Building Permits & Inspections Updated 4/30/09 Table of Contents I. Introduction... 1 II. Tips
More informationSection Section &
Pei Evaluation Service is an accredited ISO Standard 17065 Product Certifier, accredited by the IAS. This Product Evaluation Report represents a product that Pei ES has Evaluated and this product has a
More informationATI Evaluation Service A Division of Architectural Testing Certification Services
ATI Evaluation Service A Division of Architectural Testing Certification Services Subject to Renewal: 04/08/2014 Issued: 04/08/2013 Visit www.ati-es.com for current status Revision: 11/11/2013 Page 1 of
More informationCode Compliance Research Report CCRR-0194
Code Compliance Research Report CCRR-0194 Issued: 09-16-2013 Renewal Due: 09-16-2018 Revised: 10-12-2017 DIVISION: 06 00 00 WOOD, PLASTICS AND COMPOSITES Section: 06 05 23 Wood, Plastic, and Composite
More informationLP OSB Sheathing & Structural 1 Sheathing
Rated OSB Sheathing Roof Panels Span Ratings Max. Live Load Thickness Span Rating for Roofs (lbs)** 3/8" 24/0 30 7/16" 24/16 40 15/32" 32/16 70 1/2" 32/16 70 19/32" 40/20 130 23/32" 48/24 175 1-1/8" 48
More informationAttachment of Residential Deck Ledger to Metal Plate Connected Wood Truss Floor Systems
to Metal Plate Connected Wood Truss Floor Systems Structural Building Components Association (SBCA) February 17, 2015 Revised August 15, 2017 SBCA is an APPROVED SOURCE This research report is based on
More informationANSI/APA PRS Standard for Performance-Rated Structural Insulated Panels in Wall Applications
ANSI/APA PRS-610.1 Standard for Performance-Rated Structural Insulated Panels in Wall Applications 2008 APA - The Engineered Wood Association Draft 2 January 2008 Copyright 2008 by APA 7011 South 19th
More informationMaximum Spans Southern Pine Joists & Rafters
Maximum Spans Southern Pine Joists & Rafters VISUALLY GRADED LUMBER MACHINE STRESS RATED (MSR) MACHINE EVALUATED LUMBER (MEL) www.southernpine.com CONTENTS INDEX TO TABLES Floor and Rafter Framing Diagrams.......
More informationCITY OF FRUITLAND DIVISION OF PLAN REVIEW & PERMITTING DECK GUIDE. This design guide assumes all lumber to be pressure-treated Southern Pine.
City of Fruitland Building Inspections 208 South Division Street Fruitland, Maryland 21826 410.548.2804 CITY OF FRUITLAND DIVISION OF PLAN REVIEW & PERMITTING DECK GUIDE GENERAL NOTES This design guide
More informationINSULATION RETROFIT DESIGN ENERGY SOLUTIONS CENTRE YUKON GOVERNMENT
INSULATION RETROFIT DESIGN ENERGY SOLUTIONS CENTRE YUKON GOVERNMENT MAY 2009 prepared by N. A. JACOBSEN, P.Eng. CIVIL ENGINEERING CONSULTANT Whitehorse, Yukon ENERGY SOLUTIONS CENTRE YUKON GOVERNMENT MAY
More informationThe purpose of this memo is to respond to the comments received in response to the May 1, 2007, staff letter and the revised criteria.
ICC EVALUATION SERVICE, INC. Evaluate P Inform P Protect #19 To: From: ICC-ES Evaluation Committee Brian Gerber, S.E., and Irni Yani Date: June 1, 2007 Subject: Revisions to the Proposed Acceptance Criteria
More informationREPORT HOLDER: HOMELAND VINYL PRODUCTS, INC PINSON VALLEY PARKWAY BIRMINGHAM, ALABAMA EVALUATION SUBJECT:
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 1657 Reissued 01/2018 This report is subject to renewal 01/2019. DIVISION: 06 00
More informationPR-L274C Nordic Structures Revised April 16, 2017
Nordic TM PR-L274C Nordic Structures Revised April 16, 2017 Products: NI-20, 40, 40x, 60, 70, 80, 80x, 90, and 90x Prefabricated Wood I-s Nordic Structures 1100 Avenue des Canadiens-de-Montréal, Suite
More informationThis tip sheet may be used as a guide for single-family residential uncovered deck permits.
Deck Tip Sheet Information for Single-Family Residential Uncovered Deck Permit This tip sheet may be used as a guide for single-family residential uncovered deck permits. Submittal requirements: Refer
More informationNatureWood Construction Product Specification Guide
NatureWood Construction Product Specification Guide PRESERVATIVE TREATMENT Koppers Inc. Koppers Performance Chemicals PO Drawer O 1016 Everee Inn Road Griffin, GA 30224-0249 Phone: (800) 241-0240 Phone:
More informationCode Compliance Research Report CCRR-0266
Code Compliance Research Report CCRR-0266 Issue Date: 08-22-2017 Renewal Date: 08-22-2018 DIVISION: 07 00 00 THERMAL AND MOISTURE PROTECTION Section: 07 46 00 Siding Section: 07 46 33 Plastic Siding REPORT
More informationRESIDENTIAL WOOD DECK CONSTRUCTION GUIDE
RESIDENTIAL WOOD DECK CONSTRUCTION GUIDE Based on the 2015 Michigan Residential Code Revised May 17, 2016 The Following Organizations Support the use of this Guide: The details in this document apply to
More informationISO INTERNATIONAL STANDARD. Wood-based panels Oriented strand board (OSB) Definitions, classification and specifications
INTERNATIONAL STANDARD ISO 16894 First edition 2009-11-15 Wood-based panels Oriented strand board (OSB) Definitions, classification and specifications Panneaux à base de bois Panneaux de lamelles minces,
More informationDIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD I JOISTS REPORT HOLDER: STARK TRUSS COMPANY, INC.
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 2 6587 (562) 699 05 www.icc es.org ESR 2919 Reissued 11/2017 This report is subject to renewal 11/2019. DIVISION: 06 00 00 WOOD,
More informationManual for design of Guardrails
Manual for design of Guardrails for Designers, Engineers, Architects, Contractors, Installers www.allium.com Table of contents Introduction. 2 Types of guardrails systems......4 o Series 100 4 o Series
More informationESR-2645 Reissued October 1, 2013 This report is subject to renewal November 1, 2014.
ICC-ES Evaluation Report ESR-64 Reissued October, 0 This report is subject to renewal November, 04. www.icc-es.org (800) 4-68 (6) 699-04 A Subsidiary of the International Code Council DIVISION: 06 00 00
More informationDesign Manual for M.C.M.E.L Railing System
Design Manual for M.C.M.E.L Railing System FOR DESIGNERS, ENGINEERS, ARCHITECTS, CONTRACTORS & INSTALLERS. 1 - USES OF RAILINGS M.C.M.E.L. railing systems are used in homes and in residential, commercial,
More informationSECTION ELEVATED BLEACHERS (Angle Frame Semi-Closed Deck)
SECTION 13125 ELEVATED BLEACHERS (Angle Frame Semi-Closed Deck) PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and
More informationPR-L274 Nordic Structures Revised April 16, 2017
Nordic TM PR-L274 Nordic Structures Revised April 16, 2017 Products: NI-20, 40, 40x, 60, 70, 80, 80x, 90, and 90x Prefabricated Wood I-s Nordic Structures 1100 Avenue des Canadiens-de-Montréal, Suite 504
More informationDIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PLASTICS SECTION: PLASTIC RAILINGS REPORT HOLDER:
0 ICC-ES Report ICC-ES (800) 423-6587 (562) 699-0543 www.icc-es.org 000 Most Widely Accepted and Trusted ESR-3415 Reissued 09/2015 This report is subject to renewal 09/2016. DIVISION: 06 00 00 WOOD, PLASTICS
More informationPLASTERFORM GLASSFIBER REINFORCED GYPSUM (GRG) REV: 4/11
Plasterform Inc. 1180 Lakeshore Road East, Mississauga, Ontario Canada L5E 1E9 t 905.891.9500 1.800.268.4534 f 905.891.2232 plasterform.com SECTION 09285 PLASTERFORM GLASSFIBER REINFORCED GYPSUM (GRG)
More informationJoint Evaluation Report ICC-ES (800) (562)
0 Joint Evaluation Report ICC-ES (800) 423-6587 (562) 699-0543 www.icc-es.org 000 ESR-1262 Reissued 01/2018 This report is subject to renewal 01/2019. DIVISION: 06 00 00 DIVISION NAME SECTION: 06 17 33
More informationJune 1, 2009 PARTIES INTERESTED IN EVALUATION REPORTS ON STRUCTURAL WOOD-BASED PRODUCTS USED AS STUDS
June 1, 2009 TO: PARTIES INTERESTED IN EVALUATION REPORTS ON STRUCTURAL WOOD-BASED PRODUCTS USED AS STUDS SUBJECT: Proposed Revisions to the Acceptance Criteria for Wood-based Studs, Subject AC202-0609-R1
More informationCITY OF BRISTOL DECK CONSTRUCTION GUIDE ACCORDING TO THE 2012 IRC WITH THE 2016 CT AMMENDMENTS
CITY OF BRISTOL DECK CONSTRUCTION GUIDE ACCORDING TO THE 2012 IRC WITH THE 2016 CT AMMENDMENTS To construct an attached deck in to a residential home in the City of Bristol, you must provide the following:
More informationINSTALLING A CYPRESS DECK. The Natural Choice. Southern Cypress Manufacturers Association
INSTALLING A CYPRESS DECK The Natural Choice Southern Cypress Manufacturers Association Installing a Cypress Deck The Natural Choice Cypress The Natural Choice.......................... 1 Selecting the
More informationGold Bond BRAND Gypsum Sheathing
BRAND 09 06 29 16 00/NGC 43/NGC brand is a moisture-resistant sheathing installed on the outside of exterior framing as a substrate for exterior claddings. It is manufactured with a treated water-resistant
More informationThe following are details of the code requirements of the 2015 International Residential Code for single-story decks.
The following are details of the code requirements of the 2015 International Residential Code for single-story decks. The 2015 International Residential Code Section R507 contains additional information
More informationGFRP-STEEL HYBRID REINFORCED CONCRETE BRIDGE DECK SLABS IN QUEBEC, CANADA
Fourth Asia-Pacific Conference on FRP in Structures (APFIS 213) 11-13 December 213, Melbourne, Australia 213 International Institute for FRP in Construction GFRP-STEEL HYBRID REINFORCED CONCRETE BRIDGE
More informationTechnical Assessment Body issuing the ETA: Kiwa Nederland B.V. Sinh Board
Member of Kiwa Nederland B.V. www.eota.eu Sir Winston Churchilllaan 273 NL-2288 EA Rijswijk Postbus 70 NL-2280 AB Rijswijk Tel.: +31 (0)88 998 44 00 Fax: +31 (0)88 998 44 20 E-mail: info@kiwa.nl European
More informationRESIDENTIAL WOOD DECK CONSTRUCTION GUIDE
RESIDENTIAL WOOD DECK CONSTRUCTION Based on the GUIDE 2015 Michigan Residential Code Revised May 17, 2016 The following organizations support the use of this guide: The details in this document apply to
More informationPrescriptive Residential Wood Deck Construction Guide Based on the 2012 International Residential Code
Prescriptive Residential Wood Deck Construction Guide Based on the 2012 International Residential Code Where applicable, provisions and details contained in this document are based on the International
More informationPinkWood Ltd. Revised September 29, 2017
Fire-Rated Assemblies PR-S315 PinkWood Ltd. Revised September 29, 2017 Products: Series I-Joists PinkWood Ltd., 5929 6 th St. NE, Calgary, Alberta, Canada T2K 5R5 (403) 279-3700 www.pinkwood.ca 1. Basis
More informationSCREEN PORCHES 101 DEVELOPMENT RESOURCES, INC Permit Requirements
SCREEN PORCHES 101 DEVELOPMENT RESOURCES, INC. 320-226.5189 www.101developmentresources.com While every attempt has been made to insure the correctness of this handout, no guarantees are made to its accuracy
More informationREPORT HOLDER: MITEK USA, INC. (FORMERLY USP STRUCTURAL CONNECTORS) SOUTHCROSS DRIVE, SUITE 200 BURNSVILLE, MINNESOTA EVALUATION SUBJECT:
0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-2787 Reissued 05/2017 This report is subject to renewal 05/2019. DIVISION: 03 00
More informationThe Wood Products Council and AIA/CES. Concept, Performance and. Learning Objectives. FPInnovations - Background
The Wood Products Council and AIA/CES www.fpinnovations.ca Midply Shearwall System: Concept, Performance and Code Implementation C. Ni, M. Popovski FPInnovations, Building Systems The Wood Products Council
More informationFormulating a Korea Industrial Standard for light-frame wood construction
Formulating a Korea Industrial Standard for light-frame wood construction Jang, Sang Sik 1, Dong Ho Kim 2 ABSTRACT Light-frame wood construction has been widely recognized by Korean people since it was
More informationREPORT HOLDER: LOUISIANA-PACIFIC CORPORATION 414 UNION STREET, SUITE 2000 NASHVILLE, TENNESSEE EVALUATION SUBJECT:
0 Most Widely Accepted and Trusted ICC-ES Report ICC-ES 000 (00) 423-657 (562) 699-0543 www.icc-es.org ESR-3090 Issued 06/2017 This report is subject to renewal 06/2019. DIVISION: 06 00 00 WOOD, PLASTICS
More informationDIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: FIRE RETARDANT WOOD TREATMENT REPORT HOLDER: VIANCE, LLC
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2645 Reissued 11/2017 This report is subject to renewal 11/2018. DIVISION: 06 00
More informationwww.duralifedecking.com The DuraLife Your Choice Program TM Select Your Favorite Color at the Performance & Price Level You Need DuraLife makes it easy. Simply pick the deck color you like, pick the deck
More informationTrusted ICC ES SECTION: Conformity! Look. Evaluation. ICC-ES Evaluation
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.orgg ESR 3635 Reissued 04/2016 This report is subject to renewal 04/2018. DIVISION: 03 00
More informationCH. 9 WOOD CONSTRUCTION
CH. 9 WOOD CONSTRUCTION PROPERTIES OF STRUCTURAL LUMBER Grading Load carrying capacity effected by: - Size and number of knots, splits & other defects - Direction of grain - Specific gravity of wood Grading
More informationDIVISION: THERMAL AND MOISTURE PROTECTION SECTION: ROOFING AND SIDING PANELS REPORT HOLDER: KINGSPAN INSULATED PANELS, INC.
0 Most Widely Accepted and Trusted ICC-ES Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-1143 Reissued 04/2017 This report is subject to renewal 04/2018. DIVISION: 07 00 00 THERMAL
More informationSECTION SLOPED TRANSLUCENT METAL SKYLIGHT SYSTEM
PART 1- GENERAL 1.1 SUMMARY A. Section Includes: SECTION 084523 - SLOPED TRANSLUCENT METAL SKYLIGHT SYSTEM 1. Flat factory prefabricated structural insulated translucent sandwich panels; with glazed endwalls.
More informationATI Evaluation Service A Division of Architectural Testing Certification Services
ATI Evaluation Service A Division of Architectural Testing Certification Services Subject to Renewal: 05/08/2016 Issued: 08/12/2015 Visit www.ati-es.com for current status Page 1 of 21 Fiber Composites,
More informationREPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS EVALUATION SUBJECT: HILTI LOW-VELOCITY POWER-ACTUATED FASTENERS
0 Most Widely Accepted and Trusted ICC-ES Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-1663 Reissued 03/2017 This report is subject to renewal 03/2019. DIVISION: 03 00 00 CONCRETE
More informationOriginally Issued: 12/18/2015 Revised: 04/14/2017 Valid Through: 12/31/2017
INTERMAT SURE-BOARD SERIES 200S STRUCTURAL PANELS CSI Section: 05160-Metal Framing Systems 1.0 RECOGNITION Intermat Sure-Board Series 200S Structural Panels have been evaluated as floor and roof sheathing
More informationLP SmartSide Strand Substrate Treated-Engineered-Wood Lap & Panel Siding Louisiana-Pacific Corporation Revised December 2, 2016
LP SmartSide Strand Substrate PR-N124(M) Treated-Engineered-Wood Lap & Panel Siding Louisiana-Pacific Corporation Revised December 2, 2016 Product: LP SmartSide Strand Substrate Treated-Engineered-Wood
More informationICBO Evaluation Service, Inc Workman Mill Road, Whittier, California *Revised April 2003
PFC-5804* Reissued February 1, 2003 ICBO Evaluation Service, Inc. 5360 Workman Mill Road, Whittier, California 90601 www.icboes.org Filing Category: DESIGN Wood PACIFIC WOODTECH CORPORATION PWI JOISTS
More informationDIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD I-JOISTS REPORT HOLDER: PACIFIC WOODTECH CORPORATION
0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-1225 Reissued 10/2017 This report is subject to renewal 10/2019. DIVISION: 06 00
More informationBuild higher and faster with FIRM-FILL CMD (corrugated steel deck) from Hacker Industries, Inc., the leader in pourable floor underlayments.
Build higher and faster with FIRM-FILL CMD (corrugated steel deck) from Hacker Industries, Inc., the leader in pourable floor underlayments. Designed for use in multi-family, commercial and institutional
More informationLVL Product Guide 2.0E LVL 1.5E LVL
LVL Product Guide 2.0E LVL 1.5E LVL Our Company Anthony Forest Products Company, a family-owned business founded in 1916, is headquartered in El Dorado, Arkansas. The company operates a southern pine lumber
More informationDIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PLASTICS SECTION: PLASTIC RAILINGS REPORT HOLDER:
0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2995 Reissued 01/2017 This report is subject to renewal 01/2018. DIVISION: 06 00 00 WOOD, PLASTICS
More informationDIVISION: THERMAL AND MOISTURE PROTECTION SECTION: THERMAL INSULATION SECTION: WATER-RESISTIVE BARRIERS/WEATHER BARRIERS
0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-1504 Reissued 03/2017 This report is subject to renewal 03/2018. DIVISION: 07 00
More informationDIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL WALL PANELS REPORT HOLDER: METL SPAN, A DIVISION OF NCI GROUP, INC.
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2218 Reissued 09/2017 This report is subject to renewal 09/2018. DIVISION: 07 00
More informationHalar ECTFE. Ethylene-Chlorotrifluoroethylene Typical properties
Halar ECTFE Ethylene-Chlorotrifluoroethylene Typical properties Halar ECTFE A unique combination of properties Halar ECTFE is a melt-processable fluoropolymer manufactured by Solvay Solexis in Orange,
More informationDIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: NAILS REPORT HOLDER: BOSTITCH FASTENING SYSTEMS
0 Most Widely Accepted and Trusted ICC-ES Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-2122 Reissued 03/2017 This report is subject to renewal 03/2018. DIVISION: 06 00 00 WOOD, PLASTICS
More informationOverview of the New Mid-Rise Handbook Alberta Wood Solutions Fair
Overview of the New Mid-Rise Handbook Alberta Wood Solutions Fair Conroy Lum, P.Eng. Research Leader Structural Performance Group Advanced Building Systems February 12, 2015 Calgary Copyright Materials
More informationAS Residential timber-framed construction Part 2: Non-Cyclonic Areas
AS 1684.2 2010 Residential timber-framed construction Part 2: Non-Cyclonic Areas AS This Australian Standard was prepared by Committee TM-002, Timber Framing. It was approved on behalf of the Council of
More informationTHIS SECTION ASSUMES THE PROJECT MANUAL CONTAINS COMPLETE DIVISION 01 DOCUMENTS, INCLUDING THE FOLLOWING SECTIONS:
PLC LONG-TERM WOOD TREATMENT PRODUCT SPECIFICATION IN CSI 3-PART FORMAT Accsys Technologies Headquarters Brettenham House Lancaster Place London WC2E 7EN United Kingdom T: +44 207 4214300 United States
More informationPh: Fax Web: East Philadelphia Street Ontario, California USA
TEST REPORT Ph: 909.472.4100 Fax 909.472.4243 Web: www.iapmo.org 5001 East Philadelphia Street Ontario, California 91761-2816 - USA Report Number: 1724-12001 Report Issued: July 27, 2012 Project No.: 20581
More informationJoint Evaluation Report ICC-ES (800) (562)
0 Joint Evaluation Report ICC-ES (800) -658 (56) 699-05 www.icc-es.org 000 ESR-0 Reissued 0/0 This report is subject to renewal 0/08. DIVISION: 06 00 00 WOOD, PLASTICS AND COMPOSITES SECTION: 06 6 00 SHEATHING
More informationTreads, Tread Repair Covers and Nosings
ALGRIP Slip-Resistant Metal Stair Treads, Tread Repair Covers and Nosings Remarkably versatile, slip-resistant tread solutions for new and existing stairways ALGRIP Slip-Resistant Metal Stair Treads, Tread
More informationPIP STF05511 Fixed Industrial Stairs
TECHNICAL CORRECTION January 2017 Structural PIP STF05511 Fixed Industrial Stairs PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES In an effort to minimize the cost of process industry facilities, this Practice
More informationEVALUATION OF DIZAL INC
EVALUATION OF DIZAL INC., PRINTED ALUMINUM SIDING SYSTEM IDENTIFIED AS DIGITALLY PRINTED ALUMINUM SIDING / 6 FOR IMPACT RESISTANCE IN ACCORDANCE WITH ISO 7895 Report to: DiZal Inc. 1020 Bouvier, Suite
More informationDIVISION: THERMAL AND MOISTURE PROTECTION SECTION: COMPOSITE RUBBER SHAKES REPORT HOLDER: DAVINCI ROOFSCAPES, LLC
0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-2119 Reissued 08/2017 This report is subject to renewal 08/2019. DIVISION: 07 00
More informationMASTER GUIDE SPECIFICATION
TOTALJOIST (TJ) GUIDE NOTE: This master specification section includes TOTALJOIST GUIDE NOTEs identified as TJ GUIDE NOTE for information purposes and to assist the specification writer in making appropriate
More information