SPECIAL SPECIFICATION 2042 Decorative Colored Pattern Concrete Paving
|
|
- Blanche Townsend
- 6 years ago
- Views:
Transcription
1 2004 Specifications CSJ SPECIAL SPECIFICATION 2042 Decorative Colored Pattern Concrete Paving 1. Description. This Item shall govern for the furnishing and placing of colored concrete wave pattern pavement in accordance with the details shown on the plans and the requirements of these specifications. An Integral color admixture will be used to color the large wave pattern colors. An integral color admixture will be incorporated into concrete with Dry Shake Color Hardener to create additional colors in the small wave pavement pattern as indicated on drawings. The colored paving shall be broom finished as approved by Engineer from mockup review. Concrete tooled jointing will be used to separate adjacent colors. 2. Quality Assurance. Installer of the Colored Pattern Concrete Pavement shall have the minimum following qualifications: (1) Provide Experienced On-Site Supervision. The installer shall provide a qualified foreman or supervisor who has a minimum of three years experience with stamped or imprint textured colored concrete and who has successfully completed at least five stamped or imprint textured colored concrete installations of high quality and similar in scope to this project, using the stamp and color system proposed for this project. (2) Provide Certified Licensed Contractor. The installer shall provide cast-in-place concrete on the job site by trained and experienced workmen who have a minimum of three years experience with stamped or imprint textured colored concrete and who have successfully completed at least five colored concrete installations of high quality and similar in scope to this project, using the color system proposed for this project (3) Perform Work According to ACI. Perform work in accordance with ACI 301, 302, 303. (4) Provide Same Source Materials. Obtain materials from same source throughout colored concrete installation. (5) Follow Applicable Department Regulations. Conform to applicable codes and regulation for paving work performed within the public right-of-way. 3. Materials. All materials shall conform to the respective requirements of Items 420, Concrete Structures ; 421, Hydraulic Cement Concrete and DMS-4640, Chemical Admixtures for Concrete with the following exceptions: (1) Cement. Portland cement shall be Type 1. The same brand and source shall be used throughout the structure. (2) Coarse Aggregate. The coarse aggregate shall consist of durable particles of natural or crushed gravel and shall conform to Item 421, Hydraulic Cement Concrete
2 If utilizing integral color admixture, aggregate must be non-reactive. Gradation for coarse aggregate shall be as shown on the plans. (3) Fine Aggregate. Fine aggregate shall consist of clean, hard, durable and non-coated particles of natural or manufactured sand or a combination thereof, with or without mineral filler and shall conform to Item 421, Hydraulic Cement Concrete. If utilizing integral color admixture, aggregate must be non-reactive. Gradation for fine aggregate shall be approved by the Engineer. (4) Concrete. The concrete shall be Class A. An air entraining agent and/or a Type A water-reducing or a Type D water-reducing retarding admixture complying with DMS- 4640, Chemical Admixtures for Concrete may be used. Add integral color admixture in quantities recommended by coloring admixture manufacturer to achieve selected color. The concrete shall not contain any admixture or additive that contains calcium chloride. Provide a 3 minimum to 5 maximum slump mix. Add polypropylene fiber reinforcement at point of concrete batching and at manufacturer recommended quantity. Strength specimens shall be made, cured and tested in accordance with Test Method Tex-448-A. (5) Fiber Reinforcement. ASTM C948, collated, fibrillated 3/4 inch (19mm) long virgin polypropylene fibers. (6) Integral Color Admixture. Color admixture shall be a single-component, colored, water-reducing, set-controlling admixture, factory formulated and packaged in cubic yard dosage increments, not multiple additives and pigments added separately into the mix. Color admixture shall conform to ASTM 979. One (1) color as shown on the drawings. (7) Color Hardener. Commercially manufactured pigmented dry-shake color hardeners, or equal are to be used. Three (3) colors as shown on the drawings. (8) Curing Agent. As recommended by color manufacturer. Water based emulsion color cure complying with ASTM 309 as a curing membrane and with all applicable air pollution regulations is to be used. (9) Sealing Agent. Water based concrete and masonry sealer, single component, epoxymodified, penetrating type. VOC, EPA, OSHA and FDA compliant. VOC shall be less than 130 grams/liter. Skid resistance shall conform to ASTM C requirements. Product is to dry clear with a satin sheen to a semi-gloss. (10) Wave Jointing Tools. 1/8 x 4 minimum height flexible plastic strips for creating variable, smooth radius S -curve wave joint lines for tooling. (11) Joint Filler. Asphalt impregnated fiberboard, ASTM D1751, 1/2 inch (12mm) thick. (12) Joint Backer Rod. Extruded, molded closed cell neoprene foam rod. (13) Joint Sealant. Two part polyurethane sealant, urethane, SL grade. Color: from manufacturer s full range. One sealant color for each concrete color
3 (14) Bonding Agent. ASTM C1059, Type II, non-redispersible, acrylic emulsion or styrene butadiene rubber. (15) Epoxy-Bonding Adhesive. ASTM C881, two component epoxy resin, capable of humid curing and bonding to damp surface, of class and grade to suit requirements. Types I and II, non-load bearing, for bonding hardened freshly poured concrete to hardened concrete. 4. Contractor-Provided Pre-Construction Test Specimen and Mock-Ups. The Contractor shall supply a 1 yard square minimum (approximately 3 in. thick) test specimen of each color, showing each color, joint type, pattern, and texture to be duplicated in the field for approval by the Engineer prior to beginning work on the mock-ups. After approval of the test specimen, provide two full wave pattern pavement mock-ups with surface colors, textures and patterns specified, for architect approval prior to beginning the work. Provide one mock-up in the pavement grid north of FM407 adjacent to the u-turn lane loop and one mock-up in the pavement grid south of FM407 adjacent to the u-turn lane loop. Remove test specimen from the project site after acceptance of the Mock-Ups. (1) Mock-Up Size. Provide one full 11 wide x 12-6 long section within the 4 wide concrete band grid shown on the drawings. (2) Mock-Up Revisions. The mock-ups are to be constructed as part of the finished work, to dimensions, textures, colors, joints and appearance as indicated on drawings. Refinish or remove and replace the mock-ups as required by the Engineer to produce acceptable work that will become the approved standard for workmanship, quality and appearance. (3) Purpose. The purpose of the contractor-provided mock-up wave pavement is to demonstrate the Contractor s ability to meet requirements for design dimensions, concrete form wave pattern jointing appearance and stamped colored finish uniformity, technique and coverage, and other work as described herein and shown in the plans. Approved contractor-provided pre-construction mock-up paving will become the Engineer s standard by which acceptability of the aesthetics of the general installation will be judged. All constructed work, including the variation of appearance between separate batches/pours of cast-in-place stamped colored concrete and between adjacent pavement waves, shall be within the color range specified. (4) Protect the Mock-Up. The Contractor shall be responsible for protection and maintenance of approved mock-up wave pavement examples throughout the duration of the Project, including repairing damages and refinishing to match condition of adjacent work. All mock-up paving shall meet the requirements, be constructed at the sole expense of the Contractor, and will remain the Contractor s property at the conclusion of the Project, unless accepted as finished work in place as designed. (5) Replace Damaged Mock-Ups. Immediately remove and replace all mock-up pavement that are damaged beyond the point of acceptable repair, in the opinion of the Engineer, until project completion and final project acceptance
4 (6) Inspection Conditions. The mock-ups and patches will be evaluated and inspected by the Engineer during dry daylight conditions at a distance of 10 feet following cleaning by the Contractor as necessary to remove dirt, debris and other contamination interfering with the ability to judge the acceptability of the aesthetics of the completed work. 5. Appearance and Finish. The constructed work will be compared with the approved mockup samples for conformance with the color and finish requirements of this specification. The Engineer will review for acceptance (in accordance with the requirements stated herein) of the uniformity in color, quality of surface finishes, and other appearance characteristics of the completed concrete work. (1) Work that fails to meet the Contract requirements and is inadequate to serve the design purpose, including appearance qualities specified in this Special Specification, will be considered defective and a default by the Contractor under the Contract, and the Engineer may require the correction of removal and replacement at the Contractor s expense. Decisions regarding defective work will be made by the Engineer. (2) Finish all exposed surfaces with a mild detergent, light broom scrub and light power wash cleaning or other method as shown on the plans or approved by the Engineer prior to their evaluations. Multiple cleanings may be required to achieve acceptable results. 6. Construction Methods. Any required excavation and backfill shall be done in accordance with Item 400 Excavation and Backfill for Structures, except for measurement and payment, and/or in accordance with Items 110 Excavation, and 132 Embankment. The Contractor shall supply a 1 yard square minimum (approximately 3 in. thick) test specimen showing each color, pattern, and texture to be duplicated in the field for approval by the Engineer prior to beginning work on the mock-ups. (1) When utilizing integral color admixture, good batch to batch uniformity shall be maintained. The same brand of cement, source of sand, and water/cement ratio should be maintained for each load of concrete of the same color. After adding color, mixer should operate at mixing speed for at least 10 min. Concrete should be placed when weather conditions can remain constant throughout pour and finishing operations. (2) Stop concrete pours intentionally at plan locations of expansion joints or construction joints only. Provide sealed expansion joints with joint filler along walls, along curbs, around columns, and where shown on plans. When stopping concrete pour at construction joints, install sheet metal joint assembly of sufficient section to prevent deflection. Provide tooled construction joints, scored to a minimum depth of ¼ of slab thickness and at intervals indicated. Seal all expansion and joints. (3) The concrete mix shall be placed and screeded to the proper grade and wood floated to a uniform surface in the normal manner. (4) The colored hardener, where utilized, shall be applied evenly to the plastic surface by the dry-shake method using a minimum of 65 lb. per 12 sq. yd. It shall be applied in 2 separate applications, wood floated after each application, and troweled only after the final floating
5 (5) While the concrete is still in the plastic stage of set, using special forming tools approved by the Engineer, the concrete shall be tooled and finished to create the surface as shown on the plans and as approved by the Engineer. (6) The colored curing and finishing compound used shall be thinned and applied in accordance with manufacturer's directions. The coverage shall be approximately sq. ft. per gal. Plastic sheeting shall not be used. 7. Measurement. This Item will be measured by the square yard of the thickness specified using the dimensions shown on the plans. This is a plans quantity measurement Item and the quantity to be paid for will be that quantity shown in the proposal and on the Estimate and Quantity sheet of the contract plans, except as may be modified by Article 9.8. If no adjustment of quantities is required, additional measurements or calculations will not be required. 8. Payment. The work performed and materials furnished in accordance with this Item and measured as provided under Measurement will be paid for at the unit price bid for Colored Textured Concrete of the type and thickness specified. This price shall be full compensation for furnishing, placing, jointing, finishing, curing, cleaning and sealing of the colored pattern concrete. The preparation of the test specimen and mock-ups described in this specification will not be paid for directly and shall be considered subsidiary to the appropriate bid item. The above payment shall be full compensation for all materials, tools, labor, equipment and incidentals necessary to complete the work. Compacted Subgrade and base required for the stamped colored concrete will not be paid directly but will be subsidiary to this item. The Engineer reserves the right to require complete removal and replacement of concrete that does not conform to the approved contractor-provider mock-up panels. Removal and replacement of work rejected will be at the Contractor s sole expense
2014 Capital Project Phase 3 Grand Island Central School District Cannon Design Project No SECTION PAVING PART 1 - GENERAL
SECTION 321200 - PAVING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. The Contractor for this work shall be held to have read all of the Bidding Requirements, the Proposal Forms, the General Conditions of
More informationDIVISION 3 HEAVY DUTY CONCRETE FLOOR TOPPING SECTION 03340
DIVISION 3 HEAVY DUTY CONCRETE FLOOR TOPPING SECTION 03340 PART 1 - GENERAL 1.01 GENERAL REQUIREMENTS A. The General provisions of the contract, including GENERAL CONDITIONS, SUPPLEMENTARY CONDITIONS AND
More informationCustom Polishing Systems
Custom Polishing Systems VitraFlor by Bomanite Guideline Specification Standard Application PART 1 GENERAL SECTION 033000 CAST-IN-PLACE CONCRETE 1.1 RELATED DOCUMENTS A. Drawings and general provisions
More informationITEM 6 CONCRETE CURBS, GUTTERS, AND SIDEWALKS
ITEM 6 CONCRETE CURBS, GUTTERS, AND SIDEWALKS 6.1 DESCRIPTION This work shall consist of constructing curbs, gutters, sidewalks, ramps, local depressions and driveways of the form and dimensions shown
More informationSpecifications. Specifications (Architectual) Metallic System. Metallic System
(Architectual) Metallic System Architectual NeverStrip Floor Coatings, 6-15 Mils Master Format Section 096700 Fluid Applied Flooring 1 of 6 NeverStrip Metallic High-Build Decorative Epoxy/Urethane Coating
More informationSECTION CONTROLLED LOW STRENGTH MATERIAL
SECTION 03300 CONTROLLED LOW STRENGTH MATERIAL PART 1 GENERAL 1.1 DESCRIPTION A. This Section specifies Controlled Low Strength Material (CLSM) to be used as described in this specification, including
More informationMay 8, 2017 ADDENDUM #1. IFB Resin Floor System For Highway Department Central District Building
May 8, 2017 ADDENDUM #1 IFB 17-082 Resin Floor System For Highway Department Central District Building Addendum #1 is being issued to offer an alternate resin flooring system. 096700 FLUID-APPLIED FLOORING
More information1.1 Related Work Specified in Other Sections (Delete if Not Applicable):
NOTE TO SPECIFIER: Concrete Resurfacing (Broom Finish) System provides an economical alternative to the removal and replacement of existing concrete. This system creates a flexible and durable finish that
More informationSECTION CAST-IN-PLACE CONCRETE
SECTION 03300 CAST-IN-PLACE CONCRETE PART 1 GENERAL 1.01 SUMMARY A. Furnish equipment, materials, and labor required for the supply, casting, finishing, curing, and testing of cast-in-place concrete, as
More informationSECTION RIGID PAVEMENT. 1. Portland Cement Concrete (PCC) pavement. 2. Section Aggregate Base Course.
SECTION 02750 RIGID PAVEMENT PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Portland Cement Concrete (PCC) pavement. B. Related Sections: 1.2 REFERENCES 1. Section 02315 Excavation. 2. Section 02721
More informationSECTION CAST-IN-PLACE CONCRETE
SECTION 03300 CAST-IN-PLACE CONCRETE PART 1 GENERAL 1.01 SECTION INCLUDES A. The Contractor shall furnish all work and materials, including cement, sand and coarse aggregate, water, admixtures, curing
More informationSECTION CAST IN PLACE CONCRETE FOR FLOOR SLABS ON GRADE THAT WILL RECEIVE SEMI-PERMEABLE OR IMPERMEABLE FLOOR FINISHES
GUIDE SPECIFICATION SECTION CAST IN PLACE CONCRETE FOR FLOOR SLABS ON GRADE THAT WILL RECEIVE SEMI-PERMEABLE OR IMPERMEABLE FLOOR FINISHES PART 1 - SCOPE 1.01 WORK INCLUDED: 1.1.1 This guide covers the
More informationA. Testing Laboratory Services: Section B. Excavation, Site Fill and Rough Grading: Section Sub-Base Course Material (If requested).
SECTION 02500 - PART 1 - GENERAL 1.01 RELATED WORK SPECIFIED ELSEWHERE A. Testing Laboratory Services: Section 01411. B. Excavation, Site Fill and Rough Grading: Section 02200. C. Concrete: Section 03310.
More informationSECTION CONCRETE PAVING FOR PEDESTRIAN AREAS. A. This Section includes exterior cement concrete pavement for the following:
SECTION 321313 CONCRETE PAVING FOR PEDESTRIAN AREAS PART 1 GENERAL 1.1 SUMMARY A. This Section includes exterior cement concrete pavement for the following: 1. Walkways. 2. Courtyards. 3. Plazas. 4. Pedestrian
More informationSECTION CONCRETE AND MASONRY COATINGS
80658 StoColor Texture - Coarse Textured Acrylic-Based, Vertical Above-Grade Exterior Wall Coating for New Concrete, Stucco, and Masonry Construction SECTION 099723 CONCRETE AND MASONRY COATINGS Sto Corp.
More informationKOSTER AMERICAN CORPORATION
Section 09699 PART 1 GENERAL Water Vapor Emission Control Systems 1.1 RELATED DOCUMENTS A. Drawings, documents, and general provisions of the Contract, including, but not necessarily limited to, General
More informationITEM 421 STRUCTURAL CONCRETE
AFTER FEBRUARY 1, 2011 ITEM 421 STRUCTURAL CONCRETE 421.1 Description. These specifications shall govern for the materials used; for the storing, measuring and handling of materials and for the proportioning
More informationSECTION EPOXY FLOORING SYSTEMS
SECTION 09800 EPOXY FLOORING SYSTEMS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSAMPLE SPECIFICATION
SAMPLE SPECIFICATION Section 02760 Paving Specialties ROADCOLOR Epoxy Modified Bike Lane Coating System IDEAL FOR VEHICULAR BIKE LANE, BIKE LANES, for ASPHALT and CONCRETE SURFACES 1.0 GENERAL 1.1 Summary
More informationNarrow Modular Pavers (NMP) for Sand-Set Installations
The following specification refers to the Stepstone, Inc. product known as: Narrow Modular Pavers (NMP) for Sand-Set Installations Narrow Modular Pavers are part of the California Architectural Paver line
More informationG. Shop drawing of wall with all dimensions, details, and finishes. Drawings must include post foundations.
DURA-CRETE S-SERIES PRECAST CONCRETE WALL SPECIFICATIONS PART 1 GENERAL 1.01 SECTION INCLUDES A. Concrete Screen Wall Description: Work under this item shall consist of furnishing and erecting a wall in
More informationSECTION SITE CONCRETE
SECTION 321313 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting
More informationSECTION US Patent 8,857,130 B1 CAST-IN-PLACE CONCRETE WITH ARDEX CONCRETE MANAGEMENT SYSTEMS (ACMS ) EARLY MC APPLICATION
ARDEX GUIDE SPECIFICATION ARDEX CONCRETE MANAGEMENT SYSTEMS (ACMS ) Cast-In-Place Concrete to Receive the ARDEX Concrete Management Systems including ARDEX Self-Leveling Underlayments SECTION 03 30 00
More informationSAMPLE SPECIFICATION
SAMPLE SPECIFICATION Section 02760 Paving Specialties STREETCOAT Epoxy Modified Traffic Coating System IDEAL FOR VEHICULAR TRAFFIC, BIKE LANES AND COATING STAMPED ASPHALT SURFACES 1.0 GENERAL 1.1 Summary
More informationFOR PROJECTS INITIATED Page -1- AFTER FEBRUARY 1, 2010 REVISION 13 ITEM 360 CONCRETE PAVEMENT
Page -1- AFTER FEBRUARY 1, 2010 ITEM 360 CONCRETE PAVEMENT 360.1 Description. This item shall consist of a pavement of Portland cement concrete with reinforcement. The pavement shall be as shown on the
More informationCONCRETE POLISHING SPECIFICATION NEW OR EXISTING CONCRETE
CONCRETE POLISHING SPECIFICATION NEW OR EXISTING CONCRETE PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division
More informationBITUMEN-SET PRECAST CONCRETE PAVING SLABS
SECTION 32 14 13.16 BITUMEN-SET PRECAST CONCRETE PAVING SLABS (1995 MasterFormat Section 02784) NOTE: This guide specification is the U.S. for concrete paving slabs adhered with a neoprene mastic to a
More informationFrequently Asked Questions (FAQ s) about Concrete Driveways
Frequently Asked Questions (FAQ s) about Concrete Driveways What type of concrete mix should be used? Your local ready mix producer and your contractor will assist you in ensuring the proper concrete mix
More informationSection COATING RESTORATION
Sto Corp. 3800 Camp Creek Parkway Building 1400, Suite 120 Atlanta, GA 30331 Tel: 404-346-3666 Toll Free: 1-800-221-2397 Fax: 404-346-3119 www.stocorp.com 80658R StoColor Texture - Coarse Textured Acrylic-Based,
More informationDesco Quartz Cremona Specifications
Desco Quartz Cremona Specifications PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Sections, apply
More informationSECTION RESINOUS FLOORING or SECTION QUARTZ FLOORING
SECTION 09 67 23 RESINOUS FLOORING or SECTION 09 67 26 QUARTZ FLOORING PART 1 - GENERAL 1.1 SUMMARY (Specification writer shall add, delete or amend, as deemed necessary) A. Provide all labor, materials,
More informationCELCORE CELLULAR INSULATING CONCRETE SPECIFICATION FOR RETROFIT PLACEMENT OVER EXISTING ROOF MEMBRANES
PART 1: SCOPE CELCORE CELLULAR INSULATING CONCRETE SPECIFICATION FOR RETROFIT PLACEMENT OVER EXISTING ROOF MEMBRANES 1.1 An Approved Celcore Applicator shall furnish all labor, materials and supervision
More informationSECTION CAST-IN-PLACE CONCRETE
SECTION 03300 CAST-IN-PLACE CONCRETE PART 1 GENERAL 1.01 SUMMARY A. Furnish equipment, materials, and labor required for the supply, casting, finishing, curing, and testing of cast-in-place concrete, as
More informationSECTION CURB RAMPS AND OTHER MINOR CONCRETE FACILITIES. Part 1 - General Work Included Related Requirements...
SECTION 02530 CURB RAMPS AND OTHER MINOR CONCRETE FACILITIES CONTENTS: Part 1 - General... 1 1.01 Work Included... 1 1.02 Related Requirements... 1 1.03 Inspection And Tests... 1 1.04 Quality Assurance...
More informationSample Specification
Sample Specification Section 02760 Paving Specialties StencilCoat Commercial Asphalt and Concrete Surfacing System 1.0 GENERAL 1.1 Summary The StencilCoat Commercial Asphalt Surfacing System is a 100%
More informationA. Submittal Procedures: See Article 13 of the General Conditions.
SECTION 321313 - CONCRETE PAVING PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Driveways. 2. Roadways. 3. Parking lots. 4. Curbs and gutters. 5. Walks. B. Proposed Substitutions: See Article 2,
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 096623 - RESINOUS MATRIX TERRAZZO FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationSECTION SANDSTONE RESTORATION
SECTION 04 01 40.91 - SANDSTONE RESTORATION Part 1 GENERAL 1.1 SUMMARY OF WORK A. For repairing and patching of sandstone. B. Related Sections 1. Section 01351 Special Procedures for Historic Treatment
More informationCITY OF FARGO SPECIFICATIONS CONCRETE SIDEWALKS AND DRIVEWAYS
CONCRETE SIDEWALKS AND DRIVEWAYS PART 1 DESCRIPTION OF WORK The work to be done under this section of the Specifications and the accompanying plans consists of all labor, material, and equipment necessary
More informationSECTION CONCRETE. B. ACI 318 Building Code Requirements for Structural Concrete and Commentary
SECTION 03300 CONCRETE PART 1 GENERAL 1.01 SCOPE OF WORK Concrete foundation walls, sanitary structures, pipe encasements, thrust blocking and slabs on grade. 1.02 REFERENCES A. ACI 301 Specification for
More informationSECTION EPOXY TERRAZZO
SECTION 09402 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to
More informationSECTION MOISTURE RESISTANT/WATER-PROOF FLOORING ADHESIVE FOR CONCRETE SLABS
SECTION 09699 MOISTURE RESISTANT/WATER-PROOF FLOORING ADHESIVE FOR CONCRETE SLABS PART 1 GENERAL 1.1 SECTION INCLUDES A. Testing and application of systems for the reduction of moisture resistant or water-proof
More informationNarrow Modular Pavers (NMP) for Mortar-Set Concrete Tiling Installations
The following specification refers to the Stepstone, Inc. product known as: Narrow Modular Pavers (NMP) for Mortar-Set Concrete Tiling Installations Narrow Modular Pavers are part of the California Architectural
More informationBy CTS Cement Manufacturing Corp.
CSI SECTION 03 60 00 GROUTING 03 62 00 NON-SHRINK GROUTING 03 62 13 NON-METALLIC NON-SHRINK GROUTING High Flow, Non-Metallic, Multi-Purpose, Cementitious, Non-Shrink Grout EDITOR NOTE: The following guideline
More information2001 SCOPE. This section covers all cast-in-place concrete, including reinforcing steel, forms, finishing, curing, and other appurtenant work.
SECTION 2000 - CONCRETE 2001 SCOPE. This section covers all cast-in-place concrete, including reinforcing steel, forms, finishing, curing, and other appurtenant work. 2002 GENERAL. All cast-in-place concrete
More informationSECTION BITUMINOUS CONCRETE PAVEMENT
SECTION 321216 BITUMINOUS CONCRETE PAVEMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX Products
ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX Products SECTION 09 05 61.13 MOISTURE VAPOR EMISSION CONTROL PART 1 - GENERAL 1.1 RELATED DOCUMENTS
More informationB. American Concrete Institute 1. ACI 302, 1R-89 Guide for Concrete Floor and Slab Construction
SECTION 03360- CONCRETE FINISHES SPECIALIZED TERR-CON FLOORING SYSTEM PART 1-GENERAL 1.01 SUMMARY A. This section includes the following: 1. Standard placement of concrete and Terr-Con Aggregate 2. Grinding
More informationfor Mortar-Set Concrete Tiling Installations
The following specification refers to the Stepstone, Inc. product known as: Large Scale CalArc Pavers for Mortar-Set Concrete Tiling Installations Large Scale CalArc Pavers are part of the California Architectural
More informationSECTION CONCRETE LINED CANALS AND RESERVOIRS
SECTION 02511 CONCRETE LINED CANALS AND RESERVOIRS PART 1 GENERAL 1.01 SECTION INCLUDES Canal linings shall be constructed where shown on the drawings. The lining will be unreinforced concrete containing
More informationITEM 275 PORTLAND CEMENT TREATED MATERIALS (ROAD MIXED)
ITEM 275 PORTLAND CEMENT TREATED MATERIALS (ROAD MIXED) 275.1. Description. This Item shall govern for treating subgrade, new and/or existing base [with or without asphaltic concrete pavement (ACP)], or
More informationSECTION 2200 PAVING CITY OF BLUE SPRINGS, MISSOURI CONSTRUCTION SPECIFICATIONS
SECTION 2200 PAVING CITY OF BLUE SPRINGS, MISSOURI CONSTRUCTION SPECIFICATIONS The City of Blue Springs hereby adopts Section 2200 of the Kansas City Metropolitan Chapter of APWA Construction and Material
More informationA. Texas Department of Transportation 2004 Standard Specifications for Construction and Maintenance of Highways, Streets and Bridges (TxDOT).
SECTION 32 01 16 ASPHALT OVERLAY PART 1 - GENERAL 1.1 SCOPE OF WORK A. This Section specifies the requirements for scarifying, grinding, sweeping and repair of existing asphalt concrete pavement to establish
More informationSECTION EPOXY RESIN FLOORING WITH INTEGRAL COVE BASE
SECTION 09730 EPOXY RESIN FLOORING WITH INTEGRAL COVE BASE PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 03300 - Cast-in-Place Concrete. 2. 09000 - Patching and Finishes. 3. 09900 - Painting. 4.
More informationPRODUCT SPECIFICATIONS
PART 1 GENERAL 1.01 SUMMARY A. Section Includes: High density cast resin architectural products, including columns, panels, caps, bases, trim elements and balustrade systems. Specifier Note: Article below
More informationPART 1 - GENERAL. Section Cast-in-Place Concrete 1.3 REFERENCES
CSI SECTION 32 13 13 CONCRETE PAVING 32 01 26 RIGID PAVING REHABILITATION DOT APPROVED PRODUCTS LIST OR SPECIAL PROVISIONS Very Early High Strength, Low Shrinkage, Powder Polymer-Modified Concrete Overlay
More informationSECTION QUALITY CONTROL - CONSTRUCTION MANAGER EDITION
Montgomery County Public Schools Facilities DIVISION 1 - GENERAL REQUIREMENTS SECTION 01450 - QUALITY CONTROL - CONSTRUCTION MANAGER EDITION PART 1 - GENERAL 1.1 Summary: A Independent testing, inspection
More informationITEM 460 REINFORCED CONCRETE PIPE Description. This Item shall govern for the furnishing of reinforced concrete pipe.
AFTER MARCH 1, 2012 ITEM 460 REINFORCED CONCRETE PIPE 460.1 Description. This Item shall govern for the furnishing of reinforced concrete pipe. 460.2 Materials. A. Except as modified herein, materials,
More informationSECTION MODIFIED BITUMINOUS SHEET WATERPROOFING
SECTION 07 13 52 MODIFIED BITUMINOUS SHEET WATERPROOFING SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section
More informationODOT District Bridge General Notes B405: OBJECT MARKERS AND STRUCTURE/CULVERT IDENTIFICATION SIGNS
B401: DELETED B402: DELETED B403: DELETED B404: STRUCTURE/CULVERT IDENTIFICATION SIGNS B405: OBJECT MARKERS AND STRUCTURE/CULVERT IDENTIFICATION SIGNS B406: ITEM 514 - FIELD PAINTING, MISC.; REPAIR PAINTING
More informationprospec.com Concrete Repair & Restoration
prospec.com Concrete Repair & Restoration Table of Contents Product Portfolio 3 Product Enhancements 4 Product Selection Matrices 5 Construction Grout & Precast Non-shrink grouts C-1107 Construction Grout
More informationRENEW ELASTOMERIC ACRYLIC COATING (PAINT GRADE) MANUFACTURERS SPECIFICATION / SECTION
STUC-O-FLEX RENEW ELASTOMERIC ACRYLIC COATING (PAINT GRADE) MANUFACTURERS SPECIFICATION / SECTION 09 97 23 PART 1-GENERAL 1.00 SCOPE: Manufacturer's specifications containing the requirements necessary
More informationA. This Section includes resinous flooring systems with epoxy body coat(s).
SECTION 096723 - RESINOUS FLOORING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes resinous flooring systems with epoxy body coat(s). 1. Application Method: Troweled (Slurry, Seeded or Broadcast
More informationSECTION A. American Society for Testing and Materials (ASTM):
hp.seal-krete.com 306 Gandy Rd., Auburndale, FL 33823-2723 800.323.7357 863.967.1535 fax:863-965.2326 Seal-Krete High Performance Epoxy-Shell WB 50 Product Specification GUIDE SPECIFICATION SECTION 09725
More informationB. All work of the section shall comply with the conditions of the contract, the drawings and any special conditions forming a part of the contract.
SPECIFICATIONS PART ONE - GENERAL ------------------------------------------------------------------------ 1.01 General Description A. The Cementitious capillary waterproofing materials specified herein
More informationITEM P-631 REFINED COAL TAR EMULSION WITH ADDITIVES, SLURRY SEAL SURFACE TREATMENT
9/30/2009 AC 150/5370-10E ITEM P-631 REFINED COAL TAR EMULSION WITH ADDITIVES, SLURRY SEAL SURFACE TREATMENT 631-1.1 GENERAL. This item shall consist of a mixture of refined coal tar emulsion, mineral
More informationSECTION FLEXIBLE PAVING
SECTION 321200 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. Include GENERAL CONDITIONS and applicable parts of Division 1 as part of this Section. B. Examine all Drawings and other Sections of the Specifications
More informationMDC MicroTex Eggshell Micro-Textured Ceramic Coating for Walls
MicroTex Eggshell Micro-Textured Ceramic Coating for Walls Specification Guide 95: 9770 Special Wall Finishes 88: 9800 Special Coatings Part 1 General 1.01 SUMMARY A. This section specifies the furnishing
More informationPAVING SLABS ON A CONCRETE BASE
SECTION 32 14 13.16 PAVING SLABS ON A CONCRETE BASE (1995 MasterFormat Section 02784) Note: This guide specification for the U.S. is for paving slabs on a sand bed over concrete for pedestrian applications.
More informationStudent Services & Classroom Addition
SECTION 321216 - ASPHALT PAVING PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationProduct Guide Specification
Product Guide Specification Specifier Notes: This product guide specification is written according to the Construction Specifications Institute (CSI) 3-Part Format, including MasterFormat, SectionFormat,
More informationCONSTRUCTION SPECIFICATION FOR CONCRETE CROSSWALK INDEX TS SCOPE...3
CITY OF TORONTO TS 3.65 TRANSPORTATION SERVICES STANDARD CONSTRUCTION SPECIFICATIONS June 2001 CONSTRUCTION SPECIFICATION FOR CONCRETE CROSSWALK INDEX TS 3.65.01 SCOPE...3 TS 3.65.02 TS 3.65.03 REFERENCES...3
More informationSECTION CONCRETE PAVING SLABS SET IN MORTAR
SECTION 32 14 13.16 CONCRETE PAVING SLABS SET IN MORTAR (1995 MasterFormat Section 02784) Note: This guide specification for the U.S. is for paving slabs mortared to a concrete base and grouted joints
More informationSPECIAL SPECIFICATION 3048 Permeable Concrete
2004 Specifications CSJ 0713-02-007 SPECIAL SPECIFICATION 3048 Permeable Concrete 1. Description. Furnish permeable concrete with hydraulic cement and chemical admixture for use in permeable concrete pavements.
More informationThe American Society of Concrete Contractors Concrete Polishing Council SECTION BONDED ABRASIVE POLISHED CONCRETE FLOORS
SECTION 033543 - BONDED ABRASIVE POLISHED CONCRETE FLOORS PART 1 GENERAL 1.1 SUMMARY RETAIN THE BRACKETED OPTION IN THE FOLLOWING SUB-PARAGRAPH WHEN SPECIFYING COLORED FINISH. A. Section Includes: Products
More informationBroadcast Parking Garage System
AIA Specification Part 1 General Broadcast Parking Garage System 1.01 Work Included A. All work to be provided in this section shall include material, labor, and equipment necessary to furnish the complete
More informationITEM D-701 PIPE FOR STORM DRAINS AND CULVERTS
ITEM D-701 PIPE FOR STORM DRAINS AND CULVERTS 701-1 DESCRIPTION 701-1.1 This item shall consist of the construction of pipe culverts, and storm drains, removal of existing storm pipes, connections to existing
More information1.02 RELATED WORK: Refer to the following sections for related work:
SECTION 4200 - CONCRETE STRUCTURES PART 1 - GENERAL 1.01 SCOPE: This Section covers installation of header curb, retaining walls, energy dissipation structures for drainage channels, reinforced concrete
More informationA. Texas Department Transportation 2004 Standard Specifications for Construction of Highways, Streets and Bridges (TxDOT):
SECTION 31 32 13.16 CEMENT STABILIZATION PART 1 GENERAL 1.1 SCOPE OF WORK A. This Section pertains to the specifications for cement stabilization of sandy or silty soil and consists of pulverizing, addition
More informationSPECIAL SPECIFICATION 6623 Multi-Duct Conduit System
2004 Specifications Houston District SPECIAL SPECIFICATION 6623 Multi-Duct Conduit System 1. Description. Furnish and place a Multi-Duct Conduit (MDC) system that is suitable for installation in an outdoor
More informationA. The scope of this standard includes recommendations for the specification of cast-in-place concrete.
PART 1: GENERAL 1.01 Scope of Standard A. The scope of this standard includes recommendations for the specification of cast-in-place concrete. 1.02 Related Standards A. Structural Systems (currently The
More informationSECTION EPOXY TERRAZZO
SECTION 09 66 23.16 EPOXY TERRAZZO THIS GUIDE SPECIFICATION HAS BEEN PREPARED BY THE NATIONAL TERRAZZO AND MOSAIC ASSOCIATION, INC., AND IS DISTRIBUTED FOR USE BY ITS MEMBERS AND DESIGN PROFESSIONALS.
More informationInternational Polished Concrete Institute November 2006 Toll Free (866) Website
International Polished Concrete Institute November 2006 Toll Free (866) 421-9550 Website www.ipcionline.org E-mail info@ipcionline.org SECTION 03365 POLISHED CONCRETE FLOOR SYSTEM PART 1 GENERAL 1.1 SECTION
More informationSto Guide Specification No. F601S StoQuik Gold Finish System for Soffits and Ceilings
Sto Corp. 3800 Camp Creek Parkway Building 1400, Suite 120 Atlanta, GA 30331 Tel: 404-346-3666 Toll Free: 1-800-221-2397 Fax: 404-346-3119 www.stocorp.com Sto Guide Specification No. F601S StoQuik Gold
More informationMunicipality of Waterville Public Sidewalk Repair Policy
Municipality of Waterville Public Sidewalk Repair Policy Purpose - The purpose of this policy is to protect the public health, safety and welfare of the citizens and inhabitants of the Municipality by
More informationINDEX FOR SPECIFICATIONS FOR JACKING CULVERTS THROUGH EMBANKMENTS SCOPE... 2
INDEX FOR SPECIFICATIONS FOR JACKING CULVERTS THROUGH EMBANKMENTS 410. 1 SCOPE... 2 410. 2 DEFINITIONS 2.1 Tunneling and Jacking... 2 2.2 Tunneling... 2 2.3 Jacking... 2 410. 3 MATERIALS 3.1 General...
More informationSTANDARD SPECIFICATION FOR CRIBLOCK CONCRETE CRIBWALL
STANDARD SPECIFICATION FOR CRIBLOCK CONCRETE CRIBWALL 1. SCOPE 2. DESIGN 3. MATERIALS 4. CONSTRUCTION 5. METHOD OF MEASUREMENT AND PAYMENT SCOPE This Specification sets out requirements for the design,
More informationSTANDARD SPECIFICATIONS FOR PUBLIC WORKS CONSTRUCTION CITY OF WEST BEND SECTION 500 CONCRETE CONSTRUCTION 502 MATERIAL SPECIFICATIONS - GENERAL
STANDARD SPECIFICATIONS FOR PUBLIC WORKS CONSTRUCTION CITY OF WEST BEND SECTION 500 CONCRETE CONSTRUCTION Section Number Title 501 CONCRETE - GENERAL 502 MATERIAL SPECIFICATIONS - GENERAL 503 CONSTRUCTION
More informationPCC Pavement Mix Proportioning and Strength
Supplemental Technical Specification for PCC Pavement Mix Proportioning and Strength SCDOT Designation: SC-M-501 (03/08) 1. SCOPE 1.1. This supplemental technical specification describes materials and
More informationRecommended Specifications For Portland Cement Pervious Pavement
Recommended Specifications For Portland Cement Pervious Pavement Foreword Portland Cement Pervious Concrete Pavements have become increasingly popular as a method to meet water quality water run off regulations
More informationEngine Bay Floors Floor Resurfacing 4000
Engine Bay Floors Floor Resurfacing 4000 P.O. Box 341 Macungie, PA 18062 610.530.7710 800.573.9198 www.enginebayfloors.com 1.1 SUBMITTALS Flooring Specification SECTION 1 GENERAL A. Product Data: Submit
More informationMICHIGAN DEPARTMENT OF TRANSPORTATION
MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR OPEN-GRADED DRAINAGE COURSE, MODIFIED FOR JOB NUMBER 110616 (PORTLAND CEMENT-TREATED PERMEABLE BASE USING CRUSHED CONCRETE) CFS:JFS 1 of 5 APPR:ARB:TES:11-06-14
More informationSECTION 941 PRECAST REINFORCED CONCRETE BARRIERS
941.01 Scope - This Section covers the quality and manufacture of precast reinforced concrete roadside and median barriers for highway and other off-highway traffic confinement use. The concrete traffic
More informationBIO-AQUIFER STORM SYSTEM
BIO-AQUIFER STORM SYSTEM Specifications for Construction PART 1 GENERAL 1.01 SECTION INCLUDES A. Providing labor, materials, tools and equipment to furnish and install a permeable concrete paving stone
More informationA. Section includes hydraulic-cement-based, polymer-modified, self-leveling underlayment for application below interior floor coverings.
SECTION 03 54 16 - HYDRAULIC CEMENT UNDERLAYMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationDesco Mosaic Flooring Specifications
Desco Mosaic Flooring Specifications PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Sections, apply
More informationCSI SECTION MAINTENANCE OF CONCRETE Repair & Resurfacing with Rapid Hardening, High Strength, Low-Shrink, Non-Metallic Cementitious Materials
CSI SECTION 03 01 00 MAINTENANCE OF CONCRETE Repair & Resurfacing with Rapid Hardening, High Strength, Low-Shrink, Non-Metallic Cementitious Materials EDITOR NOTE: The following guideline specification
More informationSECTION 39 - MANHOLES TABLE OF CONTENTS 39-1 GENERAL PRECAST CONCRETE MANHOLES
Section SECTION 39 - MANHOLES TABLE OF CONTENTS 39-1 GENERAL... 39-1 39-2 PRECAST CONCRETE MANHOLES... 39-1 39-2.01 Precast Concrete Storm Drain Manholes... 39-1 39-3 SADDLE MANHOLES... 39-2 39-3.01 Saddle
More informationA. Section includes surface preparation and application of wood finishes[.]
SECTION 09 93 00 - STAINING AND TRANSPARENT FINISHING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationTECHNICAL SPECIFICATION
TECHNICAL SPECIFICATION ITEM 00223 LIME-FLYASH OR FLYASH STABILIZED SUBGRADE 223.1 Description. This item shall consist of treating the subgrade by the pulverizing, addition of lime flyash and/or flyash,
More information