Purpose and Scope Instructions for the installation of Dex-O-Tex Cheminert CFS epoxy flooring over previously prepared surfaces.
|
|
- Sandra King
- 6 years ago
- Views:
Transcription
1 Purpose and Scope Instructions for the installation of Dex-O-Tex Cheminert CFS epoxy flooring over previously prepared surfaces. Thickness... 3/16 (4.76 mm) minimum Colors Available Available in combinations of 18 standard blends of quartz aggregate colors as shown on standard Decor- Flor CFS color chart. Special blends are available in colors including red, blue, green, brown, beige, tan, gray, white, and black for an additional cost. Approximate Quantity of Materials Required To Cover ONE HUNDRED SQ. FT (9.3 sq. meters) Description/Packaging Amount Required C Bondcoat Unit 3 Comp. A (2 gal.) units Comp. B (1 gal) Cheminert K Basecoat Resin Comp. C (1 gal.) units Comp. D (1 quart) units Cheminert K Aggregate 1/8 (50 lb. bag) bags Decor-Flor Resin Comp. C (1 gal. ) units Comp. D (1/2 gal) units Decor-Flor Aggregate (70 lbs) bags Or (with no recovery) bags NOTES 1. All materials are also available in bulk packaging. 2. Cheminert K Basecoat Resins should be ordered in a color approximating the predominant chip color of the Decor-Flor Aggregate. 3. Where base is to be applied, order Dex-O-Tex Thickener Powder for mixing with Bondcoat and basecoat prior to applying Basecoat to verticals. Quantity required will be approximately 1/4 lb. (113 g) per 100 sq. ft. (9.3 sq. meters) of base. 4. Extra Decor-Flor Aggregate must be ordered for smaller jobs where broadcast aggregates can not be recovered for re-use. An additional quantity of 1 bag per 100 sq. ft. of aggregates is required for broadcasting of aggregates where work is not repetitive and aggregates cannot be recovered for re-use. 5. Where Decor-Flor cove base is to be installed, it should be placed by trowel, grouted and sealed before the floor application begins. 6. Decor-Flor cove base four inches (10 cm) high will require approximately.010 units of Decor- Flor Floodcoat;.006 bag (.4 lbs.) (0.18kg) Decor- Flor Aggregate and desired amount of thickener powder (approximately 2 oz by volume) per lineal foot (30 cm). 7. If two coats of Floodcoat Finish are required order an additional.57 units of Decor-Flor Floodcoat. Surface Preparation A. Concrete: See Crossfield Products Corp. Specification S-2. B. Wood and Other Surfaces: Consult Crossfield Products Corp. Job Site Survey A. Perform moisture testing in accordance with one of the following methods: ASTM F1869 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride. Verify and document the results in accordance with the specification. If MVER exceeds 3 lbs./24 hrs./1000 sq. ft. and is under 10 lbs./24 hrs./1000 sq. ft., apply Dex- O-Tex VaporControl Primer 200 as per Application Specification S-970. If MVER exceeds 10 lbs./24 hrs./1000 sq. ft. and under 15 22* lbs./24 hrs./1000 sq. ft., apply VaporControl Primer 100 as per application specification S-972. Dex-O-Tex Application Specification Page 1 of 5 Cheminert CFS
2 ASTM F2170 Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes. Verify and document the results in accordance with the specification. If the insitu relative humidity (rh) of the substrate is greater than 75% and less than 84%, apply Dex-O-Tex VaporControl Primer 200 as per Application Specification S-970. If the in-situ relative humidity (rh) is greater than 84%, and less than 89 99%*, apply VaporControl Primer 100 as per Application Specification S-972. *Apply VaporControl Primer 100 at the specified thickness required as per Application Specification S-972 for the level of MVER or insitu relative humidity percentage of the substrate. B. Inspect substrate to verify proper preparation before applying any materials. C. Measure and record ambient temperature and humidity, surface temperature and the temperature of the material being used. Do not proceed with the application if the conditions are outside the recommended parameters. D. Inspect materials to be used. Verify material is the proper material and all components and sizes are correct. Inspect all containers and verify a proper factory seal with no signs of damage or leakage. Premix Liquid materials into a smooth homogenous blend before uses. Environmental Conditions All materials are mixed, applied and cured at the job site. Minimum environmental conditions are required to facilitate proper curing and Performance of the Products. Ensure conditions are in accordance with the following requirements. Substrate Temperature 55 O F 90 O F Relative Humidity NA 78% MVER NA 3 lbs* Materials Temperature 60 O F 85 O F * 3 lbs of MVT, per 1000 sq. ft., during a 24 hr., period as measured by ASTM F1869. Materials should be delivered in original packages and containers with seals unbroken and bearing manufacturer's labels containing brand name and directions for storage and mixing with other components. Check materials immediately upon receipt, verify all the correct materials in the correct packaging are accounted for in good condition. Sort the materials and store them in a tempered storage area. STEP ONE C Bondcoat A. The mix ratio for C Bondcoat is 2 part component A to 1 part component B (2A:1B). In a clean mixing vessel pour 2 parts C Bondcoat component A to 1 part C Bondcoat component B. Mix with a drill motor and a Jiffy mixer for (2) minutes. Working time is approximately (30) minutes. Trowel, squeegee or roller apply the mixture to the prepared surface at the rate of sq. ft. per gallon. Do not puddle the material. A unit 3 of C Bondcoat will cover approximately 225 sq. ft. (21 sq. meters) over typically absorptive concrete, when applied with squeegee and backrolled. B. Apply C Bondcoat by trowel, brush or squeegee and Backroll into a tight even coating. Apply only a thin coating. Apply evenly and remove all excess, leave no puddles. Ambient Min Max Temperature 45 O F 100 O F Relative Humidity 20% rh 85% rh Wind NA 30 mph C. C Bondcoat may be applied in three techniques: 1. Apply to a small area in a very thin coat with squeegee or trowel immediately prior to application of Cheminert. LEAVE NO PUDDLES. 2. Apply as above to large area and subsequently install Cheminert K Basecoat Dex-O-Tex Application Specification Page 2 of 5 Cheminert CFS
3 over wet C Bondcoat with mechanics working on kneeboards. 3. Apply to large area and sprinkle a small amount of dry #30 silica sand on the wet Bondcoat surface. Apply Cheminert K Basecoat the next day. The sand will produce a tooth which will keep the Cheminert Basecoat from sliding on the dried Bondcoat surface. STEP TWO Basecoat A. Add Cheminert K Basecoat Component B to Component A, being certain to drain the Component B completely. Blend with drill motor and jiffy mixing blade. Pour the liquid mix into a mixing vessel (either a 2 gallon pail for drill mixing Unit One batches or an appropriate large mechanical mixer for bulk quantities. Pour the preblended resin components into an appropriate size Mixing vessel (Approx 10 gal Pail) add one bag of Cheminert K 1/8 (fine) Aggregate. When using bulk resins add one bag of Cheminert K 1/8 (fine) Aggregate per mixed gallon of Cheminert K resin. Blend long enough to be certain the preblended A an B components have thoroughly and evenly wetted the aggregates. CAUTION: Do not pour unblended Basecoat resin components into pail containing aggregate. Always blend the Basecoat resin components first, then pour into mixing vessel and add aggregates. B. The Basecoat should be edge troweled or screeded into place (an aluminum or magnesium float is best) and then compacted into position by using a trowel held flat. Flat trowel the mix into tight closed surface, free from trowel marks or ridges. CAUTION: Do not compact the Basecoat until the material is in place. Once the Basecoat is compacted, it is very difficult to spread out. Apply Basecoat as rapidly as possible, commensurate with achieving good finish. The longer the material sets in the bucket, the more difficult it will be to spread. C. A Unit One of Cheminert K Basecoat will cover approximately 40 sq. ft. (3.68 sq. meters) of floor area at 1/8 (3.18mm) in thickness. D. At temperatures of 65 F (18C ), Cheminert K will generally set and cure hard enough to support foot traffic in approximately eight hours. E. After the Cheminert K has cured sufficiently to support foot traffic any rough areas should be scraped with the edge of a trowel and any loose aggregates, etc. vacuumed from the surface. STEP THREE - Applying Decor-Flor Base A. If coved base is to be applied, this is usually best accomplished by making a stiff mix consisting of 1/2 unit 3 of Decor Flor Floodcoat (Components A & B) mix with approximately 12 oz by volume of thickener powder into which approximately lbs. (11.32 kg) of Decor- Flor Aggregate is blended. The coved base is applied by trowel. It is also helpful to prime the base with a thickened Bondcoat and let it take an initial tack before troweling the coved base mix into place. B. Installation of Decor-Flor cove base should be made to a piece of heavy cloth tape, placed either at the bottom of the cove radius or approximately 1 ½ (3.8cm) out on the floor, to create a straight edge finish at the toe of the base. When using the method where the base terminates at the bottom of the radius, burn in the base as tightly as possible to the floor. If terminating out on the floor apply Decor-Flor base to the anticipated thickness of the floor. Remove the tape shortly after the cove base and toe have been formed and before the cove base materials cure. After cove base sets up apply tape over base and match the thickness when installing the quartz layer of the floor. STEP FOUR Decor-Flor Floodcoat A. Pour components A and B into a suitable mixing container insuring that the entire contents of the cans are transferred to the mixing container. Dex-O-Tex Application Specification Page 3 of 5 Cheminert CFS
4 Blend thoroughly with a small Jiffy Blade until the mix is homogeneous. Decor-Flor Floodcoat has a pot life of approximately 30 minutes. B. Spread the blended Decor Floodcoat materials evenly and fairly liberally over the entire surface making sure there are no dry spots or voids, using a squeegee and backrolling with a short nap roller. This material will flow out in approximately 5 to 7 minutes, filling any minor voids or depressions. The Decor Floodcoat surface must be uniform, wet and free of ridges. overlap (which can result in an uneven appearing finish). A unit 3 of Floodcoat will cover approximately sq. ft. (16.3 sq. meters). B. Floodcoat should be applied to verticals and cove base by paint brush, allowed to take an initial set and then pulled tight with a rubber squeegee to avoid puddling at the bottom of the cove base. All applications to cove base must be minimum coats, applied with care to eliminate excess deposits of Floodcoat at the cove area. C. A unit 3 of Decor Floodcoat will cover approximately 300 sq. ft. (13.94 sq. meters). D. Where work is to be stopped for the day, such as at doorways and meeting other finishes, apply a strip of heavy cloth tape to concrete prior to spreading Floodcoat. This will create a straight edge stop. Apply Floodcoat up to and slightly over the edge of the tape. Remove tape shortly after broadcasting Decor-Flor Aggregate. STEP FIVE - Decor-Flor Aggregate A. Immediately after the Floodcoat material flows out, the preblended Decor-Flor Aggregates are heavily broadcast into the Floodcoat. B. or stains not removed could be sealed into the surface. Pay particular attention to cleanliness of footwear and knee pads when sealing. STEP SIX - Floodcoat Finish A. Pour the components A and B into a suitable mixing container insuring that the entire contents of the cans are transferred to the mixing container. Blend thoroughly with a small Jiffy Blade until the mix is homogeneous. Decor-Flor Floodcoat Resin has a pot life of approximately 30 minutes. Spread the Floodcoat evenly and liberally, using a clean, soft rubber (DO NOT use Black Rubber blades) squeegee. Allow the Floodcoat to flow slightly heavy and soak into the surface. Then remove the excess material with the rubber edge squeegee. A wet edged bead of Floodcoat should be left where the next pour of Floodcoat is to be made to avoid excessive C. If a smoother finish than normal is desired, apply a second coat of Floodcoat finish. This will require an additional.20 unit 3 of Decor-Flor Resin material per 100 sq. ft. (9.3 sq. meters). General Cautions 1. Read and follow Crossfield Products Corp. Specification S For proper workability it is important that the Dex-O-Tex materials be stored and mixed at a temperature of 65 F - 80 F (18 C - 26 C). 3. The substrate temperature should be between 65 F - 80 F. A warm substrate will decrease the pot life and make the materials sticky. A cooler substrate will retard the cure and may cause a blush of the epoxy resins. 4. All concrete curing agents, sealers and hardeners must be removed from the concrete prior to application of the Bondcoat. 5. When mixing the epoxy resin components, be sure to use all of the provided resins. The resins are pre-measured to the correct ratios. Scrape all of the hardener from the container into the resin. 6. Do not turn mixing vessels upside down to drain on the flooring surface. Unmixed resin from the side may produce soft or uncured spots on the flooring surface. 7. Keep the unfinished flooring surface clean. Do not track dirt, grease, or any other contaminate onto the unfinished flooring surface. Any contaminate could effect the aesthetics of the finished flooring. 8. Good ventilation must be provided during application, particularly in confined spaces. Dex-O-Tex Application Specification Page 4 of 5 Cheminert CFS
5 9. Always obtain, read and observe Manufacturer s Safety Data Sheets (MSDS) before handling epoxy materials. Become familiar with the products on paper before you open the pails. Cautions for Safe Handling of Epoxy, Polyurethane or Polyurea Materials 1. Read and observe precautionary statements on product labels. 2. Keep containers tightly closed. 3. Keep out of reach of children. 4. For industrial use only. Do not allow application by untrained workers. 5. Remove contaminated clothing and shoes. Wash clothing before re-use. 6. Use of safety goggles and chemical resistant gloves is recommended. Wear only full-length trousers and long-sleeve shirts. Apply protective creams to exposed skin areas. 7. In general, prolonged contact of epoxies, polyurethanes or polyureas with skin may cause irritation. Contact with curing agents or polyurea resins may cause skin burns. Products may cause skin sensitization or other allergic responses. Avoid all contact with eyes. 8. In case of contact with skin, immediately remove the material with soap and water. Upon completion of work at lunchtime or end of day, carefully check all skin surfaces for any traces of resinous materials. Wash with soap and water. If wash facilities are not located nearby, establish water-washing station at work site. Do not use solvents to remove epoxy, polyurethane or polyurea materials from skin, as solvents will drive material deeper into skin. If redness or a skin rash develops, consult a physician. 9. Mix and apply materials only in conditions of good ventilation. Avoid breathing vapors. Appropriate respiratory protection is required when exposure to airborne contaminants may exceed acceptable limits. Respirators should be selected and used in accordance with OSHA, subpart I (29 CFR ). DEX-O-TEX PRODUCT LINE Crossfield Products Corp. West Coast Office East Coast Office 3000 E. Harcourt Street 140 Valley Road Rancho Dominguez, CA Roselle Park, NJ fax fax Dex-O-Tex Application Specification Page 5 of 5 Cheminert CFS
Colors Available See Color Chart.
Purpose and Scope Instructions for the application of Dex-O-Tex Posi- Tred CR slip-retardant finish over various types of surfaces including concrete, metal, ceramic tile as well as certain Dex-O-Tex floors.
More informationApplication Specification
Purpose and Scope Instructions for the application of Dex-O-Tex Decor- Flor DFS Broadcast quartz flooring. For slurry broadcast or trowel applied application or Decor-Flor used as a general utility product,
More informationThickness (dry film)... nominal 1/8 (3.2mm) to 1/4 (6.4mm) Colors Available See Standard Dex-O-Tex Color Chart with Chips (Standard White)
Purpose and Scope To outline instructions for application of Dex-O-Tex Colorflake VP, a seamless, cosmetic polymeric deck covering system with random decorative chips for interior deck covering. This material
More informationApplication Specification Over Concrete Substrates
Purpose and Scope Instructions for surface preparation and application of Dex-O-Tex Auto-Dex V as a protective and water resistant coating system for parking decks. Note: Working cracks in the concrete
More informationTEK-CRETE SLCQ. Application Specification. Severe Service Applications
Purpose and Scope Instructions for installation of Dex-O-Tex Tek-Crete SL CQ flooring, Standard Application over previously prepared concrete. Thickness Standard...1/4 (4.7mm) or 3/8 (6.35 mm) ALTERNATE:
More informationTEK-CRETE SLCF. Application Specification
Purpose and Scope Instructions for installation of Dex-O-Tex Tek-Crete SLCF flooring, Standard Application over previously prepared concrete. Thickness Standard... 3/16 (4.7mm) or 1/4 (6.35 mm) NOTE: Tek-Crete
More informationThickness... 1/4 (6.33 mm) Approximate Quantity of Materials Required To Cover ONE HUNDRED SQ. FT (9.3 sq. meters)
Purpose and Scope Instructions for installation of Dex-O-Tex Tek-Crete SL-B slurry grade polyurethane cement mortar system with full aggregate broadcast and seal coat over previously prepared concrete.
More informationPurpose and Scope Instructions for installation of Dex-O-Tex Flex- Shield ME Flooring mechanical equipment room floor standard finish profile
Purpose and Scope Instructions for installation of Dex-O-Tex Flex- Shield ME Flooring mechanical equipment room floor standard finish profile Thickness... 62 Mils DFT (2.18 mm), Nominal Colors Available
More informationApplication Specification
Purpose and Scope Instructions for the application of Dex-O-Tex Wall- Glas fabric-reinforced epoxy wall system over suitable smooth wall surfaces. Thickness... 20 mils (approx) Colors Available Select
More informationRESISTITE. Surface Preparation A. Concrete: Prepare in accordance with SSPC SP 13.
Purpose and Scope Instructions for the application of Dex-O-Tex Resistite Architectural Microtopping System over properly prepared surfaces. Thickness... 1/16 3/32 (nominal) Approximate Quantity of Materials
More informationSECTION RESINOUS FLOORING or SECTION QUARTZ FLOORING
SECTION 09 67 23 RESINOUS FLOORING or SECTION 09 67 26 QUARTZ FLOORING PART 1 - GENERAL 1.1 SUMMARY (Specification writer shall add, delete or amend, as deemed necessary) A. Provide all labor, materials,
More informationInstallation Instructions
Installation Instructions I. GENERAL INFORMATION KEY CHIP-100 FLOORING is a decorative resin flooring system consisting of clear, 100% solids epoxy resin and colored vinyl chips. KEY CHIP-100 FLOORING
More informationApplication Specification
0BMETHOD TO USE WITH MORTAR BED AND APPLICATION OF TILE OR OTHER HARD SURFACES OVER PLYWOOD SUBSTRATES. Purpose and Scope Instructions for the surface preparation and application of Dex-O-Tex Dual-Flex
More informationInstallation Instructions
Installation Instructions KEY LASTIC CHIP 100 FLOORING I. GENERAL INFORMATION KEY LASTIC CHIP-100 FLOORING is a resilient decorative resin flooring system consisting of 100% solids resilient epoxy resins
More informationEpoxy & Pebblestone Fax: We ship all over the USA U.V.
Epoxy & Pebblestone www.epoxyandpebblestone.com 623-688-6077 Fax: 623.594.7177 dave@epoxyandpebblestone.com We ship all over the USA U.V. EPOXY PHYSICAL PROPERTIES: Composition: Solids Content: Mix Ratio:
More informationSECTION EPOXY MOSAIC COMPOSITION FLOORING Dex-O-Tex Cheminert Terracolor
SECTION 09720 EPOXY MOSAIC COMPOSITION FLOORING Dex-O-Tex Cheminert Terracolor PART 1.00 - GENERAL 1.01 GENERAL REQUIREMENTS A. Work of this Section, as shown or specified, shall be in accordance with
More informationInstallation Instructions
Installation Instructions I. GENERAL INFORMATION KEY URECON SLT-HP Quartz URECON SLT-HP Quartz is a three component, self-leveling, urethane-modified cementitious topping broadcast with quartz aggregate
More informationHTG Concrete Seal. Technical Specifications. Safety. HMIS (Concentrate/RTU) Availability. Directions
HTG Concrete Seal HTG(gray) Concrete Seal is a 2-part, high-solid epoxy resin formulation for extreme durability that dries gray. Use HTG to transform bare concrete or previously coated concrete floors
More informationJewel Stone. Decorative Concrete Overlay System. Part 1 GENERAL MANUFACTURER S SPECIFICATION
SEPTEMBER 2016 Jewel Stone Decorative Concrete Overlay System MANUFACTURER S IFICATION 09 62 81 Part 1 GENERAL 1.1 RELATED SECTIONS.1 Specification 03 30 00 Cast-in-Place Concrete.2 Specification 09 70
More informationFLEXMAR 3-Coat High-Build Colored Quartz System
Guide Specification SECTION 09 67 23: HIGH-PERFORMANCE RESINOUS FLOORING FLEXMAR 3-Coat High-Build Colored Quartz System 20-27 mils DFT This guide specification is intended to assist the specifier in developing
More informationCP-24CC Potassium Silicate Concrete
CP-24CC Potassium Silicate Concrete PRODUCT DESCRIPTION Blome CP-24CC is a two component, potassium silicate concrete used for acid resistant pump pads, equipment pads, curbing, floors and sumps. CP-24CC
More informationSection SECTION RESINOUS FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 096723 - RESINOUS FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION TOPICAL MOISTURE VAPOR MITIGATION SYSTEM
TOPICAL MOISTURE VAPOR MITIGATION SYSTEM PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings, documents and general provisions of the Contract, and other related construction documents such as Division 01
More informationDIVISION 7 THERMAL AND MOISTURE PROTECTION Section Traffic Coatings
Spec Component: SC-720-03/10 Sikalastic 720/745 Traffic System DIVISION 7 THERMAL AND MOISTURE PROTECTION Section 071800 Traffic Coatings Part 1 - General 1.01 Summary A. This specification describes the
More informationResists a very wide range of organic and inorganic acids, alkalis, amines, salts and solvents.
DATE - JANUARY 2018 TECHNICAL DATA SHEET DESCRIPTION is a self-levelling, medium to heavy duty, three-components; water dispersed polyurethane-based cement and aggregate screed. It is designed to provide
More information3-component epoxy self-smoothing screed
Construction Product Data Sheet Edition 26/07/2016 Identification no: 01 08 01 02 050 0 000017 3-component epoxy self-smoothing screed Product Description Uses Characteristics / Advantages Product Data
More informationInstallation Instructions
Note: Seals are delivered in either wooden reels or large steel reels depending on order size and contractor storage ability. Store reels under a tarpaulin (tarp) to keep the seals clean and free from
More informationMcKinnon Materials, Inc th Commerce Park Blvd. Tampa FL, Phone: (813) Fax: (813)
PHYSICAL PROPERTIES: Composition: Solids Content: Mix Ratio: 3 to 1 Viscosity: Pot Life: McKinnon Materials, Inc. 5612 56 th Commerce Park Blvd. Tampa FL, 33610 Phone: (813) 622-7031 Fax: (813) 621-9017
More informationInstallation Instructions
Installation Instructions KEY MMA SLT QUARTZ I. GENERAL INFORMATION KEY MMA SLT QUARTZ is a rapid curing, 100% reactive, decorative methyl methacrylate (MMA) resin flooring system. Thickness ranges from
More informationARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX ARDIFLO Pump System Underlayments
ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX ARDIFLO Pump System Underlayments SECTION 07 26 19 TOPICAL MOISTURE VAPOR EMISSION SYSTEM WITH ARDEX
More informationSECTION A. American Society for Testing and Materials (ASTM):
hp.seal-krete.com 306 Gandy Rd., Auburndale, FL 33823-2723 863.967.1535 800.323.7357 fax: 863-965.2326 Seal-Krete High Performance Poly-Shell 7000 Single Quartz Broadcast System GUIDE SPECIFICATION SECTION
More informationRe-Grouting Floor Joints in Commercial Kitchens and Industrial Applications
Re-Grouting Floor Joints in Commercial Kitchens and Industrial Applications GENERAL CONDITIONS Degradation or deterioration of an epoxy grout can occur when the circumstances are right or when the wrong
More informationNAVSEA REVIEWED ASTM F-718. Tenacious One Step Epoxy Flooring
ASTM F-718 International Diverse Flooring Tenacious One Step Epoxy Flooring MIL-PRF-24613 If this product is to be applied as part of a coating system, all components of the system must be as listed on
More informationTECHNICAL DATA SHEET
Dy-Mark EPOXY COAT WATER-BASED DIRECTIONS FOR USE Dy-Mark All-In-One Epoxy Coat Water-Based is a fast dry floor coating that gives a professional finish to interior bare concrete floors. Epoxy Coat resists
More informationProduct Size Thickness Installation direction Seams treatment
INSTALLATION INSTRUCTIONS FOR GERFLOR SAGA 2, CREATION TILES AND PLANKS This document refers to the following products: Product Size Thickness Installation direction Seams treatment Creation Tiles See
More informationEasy to apply Nonflammable Low odor Castable Make excellent materials of construction
SELECTION & SPECIFICATION DATA Generic Type Description Features Color Primer Application Thickness Dry Film Thickness Typical Uses Polymer Concrete polymer concrete is an excellent alternative to acid
More information1.1 This procedure governs the installation of PENNTROWEL UT500 Polyurethane Mortar Flooring Systems CE-286, CE-287 and CE-288.
AN ERGONARMOR COMPANY TECHNICAL INFORMATION 05/10 Supersedes 12/09 SPECIFICATION FOR INSTALLATION PENNTROWEL UT500 SURFACER SYSTEMS 1. SCOPE 1.1 This procedure governs the installation of PENNTROWEL UT500
More informationARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX Underlayments and Toppings
ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX Underlayments and Toppings SECTION 07 26 19 TOPICAL MOISTURE VAPOR MITIGTION SYSTEM PART 1 - GENERAL
More informationSECTION RESINOUS FLOORING
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 67 23 1. Use this section only for NCA projects. 2. Delete // // if not applicable to project. Also delete any other item or paragraph not applicable in the
More informationSECTION RESINOUS FLOORING PLEXIQUARTZ BROADCAST SKID-RESISTANT QUARTZ SYSTEM
SECTION 096723 RESINOUS FLOORING PLEXIQUARTZ BROADCAST SKID-RESISTANT QUARTZ SYSTEM PART 1 - GENERAL 1.1 SUMMARY A. This section includes the following: 1. Seamless epoxy flooring system, 1/16 th, 3/32
More informationSKATE ON LAYKOLD Specification
Acrylic Sport & Recreational Surfaces SKATE ON LAYKOLD Specification PART 1 GENERAL 1.1 DESCRIPTION Scope: This guide specification covers the construction and installation for the SKATE ON LAYKOLD inline
More informationConstruction. Sikadur 35, Hi-Mod LV. Application Instructions. Sika Corporation
Sikadur 35, Hi-Mod LV Application Instructions Sikadur 35, Hi-Mod LV Structural epoxy adhesive Multi-purpose Two-component 100% solids Low viscosity Moisture-tolerant High strength Sikadur 35, Hi-Mod LV
More informationRESINOUS FLOORING
PART 1 - GENERAL 1.1 RELATED DOCUMENTS Bid #2017-17 A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this
More informationSECTION RESILIENT TILE FLOORING. A. Section includes vinyl composition floor tile and accessories indicated and as specified.
SECTION 09 65 19 RESILIENT TILE FLOORING PART 1 - GENERAL 1.1 SUMMARY A. Section includes vinyl composition floor tile and accessories indicated and as specified. 1.2 SUBMITTALS A. Product Data: Submit
More informationFlooring and Bedding. RonaFloor SL. Self-smoothing seamless epoxy resin flooring system
FEATURES self smoothing epoxy floor screed seamless high strength decorative good chemical resistance easy to clean can be applied to green concrete with use of RonaFloor Epoxy DPM Description RonaFloor
More informationSECTION A. American Society for Testing and Materials (ASTM):
hp.seal-krete.com 306 Gandy Rd., Auburndale, FL 33823-2723 800.323.7357 863.967.1535 fax:863-965.2326 Seal-Krete High Performance Epoxy Metallic System GUIDE SPECIFICATION SECTION 09725 PART 1 GENERAL
More informationTechnical Service. INSTALLATION INSTRUCTIONS FOR TARAFLEX SPORT PRODUCTS over Gypsum base Products. This document refers to the following products:
INSTALLATION INSTRUCTIONS FOR TARAFLEX SPORT PRODUCTS over Gypsum base Products This document refers to the following products: Product Width Width Ft. Installation direction Seams treatment Taraflex Surface
More informationINSTALLATION MANUAL FULLY ADHERED INSTALLATIONS
SHOCKPAD BL41 MANUAL FULLY ADHERED S Manufactured in the U.S.A. by: Revised 07/08/2015 Supersedes all previous versions. Check website for updates. 866-795-2732 www.ecoreathletic.com 1 TABLE OF CONTENTS
More informationKOSTER AMERICAN CORPORATION
Section 09699 PART 1 GENERAL Water Vapor Emission Control Systems 1.1 RELATED DOCUMENTS A. Drawings, documents, and general provisions of the Contract, including, but not necessarily limited to, General
More informationAcrylic Tennis & Recreational Sport Surfaces. ADVANTAGE Laykold System Specification
Acrylic Tennis & Recreational Sport Surfaces ADVANTAGE Laykold System Specification PART 1 GENERAL 1.1 DESCRIPTION A. Scope: This guide specification covers the application of the Advantage Laykold system.
More informationCARLISLE DECK COATING INSTALLATION OVER EXISTING POLYURETHANE COATINGS
CARLISLE DECK COATING INSTALLATION OVER EXISTING POLYURETHANE COATINGS 1. GENERAL A. When coating over existing coatings, Carlisle can not assume responsibility for the adhesion of the existing coating,
More informationTECHNICAL DATA SHEET
Dy-Mark EPOXY COAT DIRECTIONS FOR USE Dy-Mark All-In-One Epoxy Coat is a durable floor coating that gives a professional finish to interior bare concrete floors. Epoxy Coat resists hot tyre pick-up and
More informationSC-113 STRONGCOTE VEHICULAR GRADE TRAFFIC DECK MEMBRANE SYSTEM SECTION 07570
PART 1 - GENERAL 1.01 SECTION INCLUDES SC-113 STRONGCOTE VEHICULAR GRADE TRAFFIC DECK MEMBRANE SYSTEM SECTION 07570 A. SC-113, Heavy Duty Vehicular Grade Traffic Deck Membrane System with Migratory Corrosion
More informationSECTION SUBSURFACE PREPARATION FOR FLOOR FINISHES
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 05 16 SUBSURFACE PREPARATION FOR FLOOR FINISHES SPEC WRITER NOTES: 1. Delete between // // if not applicable to project. Also delete any other item or paragraph
More informationSTERI-FLAKE 470 HYBRID ESTER POLYMER, LIGHT-MEDIUM TRAFFIC, FLAKE FILLED FLOOR SYSTEM LOW ODOR MMA ALTERNATIVE FEATURES
FEATURES Low Odor & VOC Very Fast Cure Unique Multi Colored Patterns Tough, Durable & Seamless Floor Good UV Stability Protects Substrate from Chemical or Physical Attack Integral Cove, Base and Curb (optional)
More informationARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX Products
ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX Products SECTION 09 05 61.13 MOISTURE VAPOR EMISSION CONTROL PART 1 - GENERAL 1.1 RELATED DOCUMENTS
More informationProtective Industrial Polymers USA Manufacturer s Specification
This specification covers DecoSpec QuartzCast DB Decorative Quartz Double Broadcast Flooring System consisting of a moisture-tolerant primer, two applications of a high-build epoxy basecoat with two colored
More informationSECTION CONCRETE TOPPING or SECTION DECORATIVE FINISHING or SECTION CEMENTITIOUS COATINGS
CSI Master Format does not currently include a specific section number for Cementitious Microtopping Flooring systems. Specification writer shall choose the most appropriate section that applies to the
More informationMARATHON & MARATHON PLUS RUBBER TILE
SITE CONDITIONS 1. Store the flooring and adhesive in the installation area. 2. The temperature must be kept between 18 C (65 F) and 24 o C (75 o F) for 48 hours before, during and after installation.
More informationROLL ON ROCK INSTALLATION GUIDE SYSTEM 2 with 1/4 to 1 Flakes (See Roll on Rock System 2 Mini Flake Install Guide when using smaller size Flakes)
PRODUCT DESCRIPTION ROLL ON ROCK INSTALLATION GUIDE SYSTEM 2 with 1/4 to 1 Flakes (See Roll on Rock System 2 Mini Flake Install Guide when using smaller size Flakes) Roll On Rock System 2 IG Page 1 of
More informationLS 486 / GLASS MAT REINFORCED SYSTEM A LAVALINE - SERIES 48 SYSTEM / Vinyl Ester CONCRETE & MASONRY SURFACES
LS 486 / GLASS MAT REINFORCED SYSTEM / Vinyl Ester CONCRETE & MASONRY SURFACES The LS-486 system may be installed on various substrates, including carbon and stainless steel and concrete and other masonry
More informationVulkem EWS with PUMA Technology (Heavy Duty) APPLICATION INSTRUCTIONS
Vulkem EWS with PUMA Technology (Heavy Duty) APPLICATION INSTRUCTIONS 1. Purpose 1.1 The purpose of this document is to establish uniform procedures for applying the Vulkem Extreme Wearing System (EWS).
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 096519 - RESILIENT TILE FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationOVERKOTE E-100 Epoxy Floor Coating Technical Data
OVERKOTE E-100 Epoxy Floor Coating Technical Data PRODUCT DESCRIPTION OVERKOTE E-100 is a floor coating system applied at a thickness of 16 to 50 mils. It is designed for long term protection of concrete
More informationAcrylic Tennis & Recreational Sport Surfaces. COLORCOAT System Specification
Acrylic Tennis & Recreational Sport Surfaces COLORCOAT System Specification PART 1 GENERAL 1.1 DESCRIPTION A. Scope: This guide specification covers the application of the Laykold ColorCoat system. Advanced
More informationDMS EP-D80 Broadcasted Epoxy Resin Floor
Product description DMS EP-D80 system is a three component epoxy system, designed as epoxy binder containing special fire retardant additives and mineral fillers, such as quartz or granulated granite.
More informationSECTION A. American Society for Testing and Materials (ASTM):
hp.seal-krete.com 306 Gandy Rd., Auburndale, FL 33823-2723 863.967.1535 800.323.7357 fax: 863-965.2326 Seal-Krete High Performance Poly-Shell 7000 Sparse Flake System GUIDE SPECIFICATION SECTION 09725
More informationPOLYMER CONCRETE 100 EPOXY POLYMER CONCRETE DILUTE ACIDS RESISTANCE
RECOMMENDED APPLICATIONS Polymer Concrete 100 is a three-component, epoxy polymer concrete used for the construction of chemical resistant floors, pads, curbing, trenches and sumps. Polymer Concrete 100
More informationProtective Industrial Polymers - USA Manufacturer s Specification
This specification covers InhibiWear BC-Flex Flexible Broadcast System. This system consists of a moisture-tolerant primer, a highly-flexible epoxy/urethane hybrid membrane basecoat and anchor coat, and
More informationApplication Guide GARAGE & COMMERCIAL FLOORS
Application Guide GARAGE & COMMERCIAL FLOORS REQUIRED TOOLS & MATERIALS - CHECKLIST Flexstone Coatings products (ensure you have enough) Flat Squeegee and Pole (Optional) Disposable brushes (3-4 ) Roller
More informationSECTION A. American Society for Testing and Materials (ASTM):
hp.seal-krete.com 306 Gandy Rd., Auburndale, FL 33823-2723 800.323.7357 863.967.1535 fax:863-965.2326 Seal-Krete High Performance Epoxy-Shell 1000 Color System GUIDE SPECIFICATION SECTION 09725 PART 1
More informationARDEX GUIDE SPECIFICATION ARDEX K 60 ARDITEX A Rapid Setting Latex Smoothing and Leveling Compound
ARDEX GUIDE SPECIFICATION ARDEX K 60 ARDITEX A Rapid Setting Latex Smoothing and Leveling Compound SECTION 03 54 16 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general provisions of the Contract,
More informationCHARACTERISTICS / ADVANTAGES. Yellowish-transparent. PACKAGING 20 kg per pail
PRODUCT DATA SHEET Epoxy-resin binder for priming, levelling mortar and for screeds PRODUCT DESCRIPTION Sikafloor -156 is a colourless, 2-component low viscosity epoxy resin. USES For priming and levelling
More informationPROTECTO-CRETE 800/800SF
FEATURES Excellent Bond Strength to Concrete Excellent Wear Resistance RECOMMENDED APPLICATIONS Plating Room Floors Pickling Room Floors Truck Loading Platforms Chemical Storage CHEMICAL RESISTANCE Organic
More informationAPPLICATION NOTES. Epotec NT (New Technology) Please read and follow the information below to gain a quality, long lasting result.
APPLICATION NOTES Issue Date July 2018 Replaces Date Epotec NT (New Technology) Please read and follow the information below to gain a quality, long lasting result. If any questions contact COTEC on 09
More informationInstallation Instructions
Installation Instructions Before you begin, you will need the following tools and supplies: A clean or new 5 gallon bucket. You will need to either replace or clean your bucket after each 5 kits or before
More informationSECTION EPOXY RESIN FLOORING WITH INTEGRAL COVE BASE
PART 1 GENERAL 1.01 SUMMARY SECTION 09730 EPOXY RESIN FLOORING WITH INTEGRAL COVE BASE A. Related Sections: 1. 03300 - Cast-in-Place Concrete. 2. 09000 - Patching and Finishes. 3. 09900 - Painting. 4.
More informationPOWERBASE ICF / SIDER PROOF FF-PR
153 Regur Road Hawkinsville, GA 31036 USA 1.478.892.9800 888-743-3750 www.sider-crete.com Designer & Manufacturer of the original Roll-On Pool Plaster! POWERBASE ICF / SIDER PROOF FF-PR Product Data Features
More informationSTRONGCOTE SC-111 PEDESTRIAN GRADE TRAFFIC DECK COATING SYSTEM SECTION 07570
STRONGCOTE SC-111 PEDESTRIAN GRADE TRAFFIC DECK COATING SYSTEM SECTION 07570 PART 1 - GENERAL 1.01 SECTION INCLUDES A. SC-111, Pedestrian Grade Traffic Deck Membrane System with Migratory Corrosion Inhibitors
More informationColored Epoxies. Application Instructions. Typical Uses: Overview:
Colored Epoxies Application Instructions Colored Epoxies manufactures high performance Architectural coatings in two part, clear and colored epoxies, that are a cost-effective solution for substrate protection.
More informationSUBMITTED TO: PRODUCT INFORMATION: SUBMITTED BY: FOR ARCHITECT/ENGINEER USE:
SUBMITTED TO: TO: SUBMITTAL DATE: COMPANY NAME: PROJECT: PRODUCT INFORMATION: SUBMITTED PRODUCT: CRACKBOND HEALER/SEALER SPECIFIED PRODUCT: SECTION: PAGE: PARAGRAPH: DETAIL/SHEET NO.: DESCRIPTION OF APPLICATION:
More informationARDEX GUIDE SPECIFICATION ARDEX PANDOMO Floor ARDEX PANDOMO CF1 Commercial Design Leveling Compound
ARDEX GUIDE SPECIFICATION ARDEX PANDOMO Floor ARDEX PANDOMO CF1 Commercial Design Leveling Compound SECTION 09 62 00 ARDEX PANDOMO Floor System PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general
More informationTraffic Bearing Membrane
7 07 18 11 Traffic Coatings Qualideck Traffic Bearing Membrane High-solids, 2-component polyurethane waterproofing, traffic bearing systems for vehicular and pedestrian areas PACKAGING Q152 Primer: 3 gal
More informationA-9,250 Parking Structure Resurfacing Cement Look
A-9,250 Page 1 A-9,250 Parking Structure Resurfacing Cement Look Description This specification includes the repair and resurfacing methods used when applying Americrete products over cracked, spalled,
More informationSECTION HYDRAULIC CEMENT UNDERLAYMENT
ARDEX GUIDE SPECIFICATION ARDEX Underlayment HC 100 High-Capacity Self-Leveling and V1200 Self-Leveling Flooring Underlayment Cement-based Self-Leveling Underlayment for use with ARDEX ARDIFLO System SECTION
More informationPROTECTO-CRETE 140T/140TSF
FEATURES Low Odor VOC Compliant Can be used for Coving, Pitch and Curb Construction 100% Solids RECOMMENDED APPLICATIONS Pulp and Paper Mills Dike Areas Chemical Storage Pickling Room Floors Truck Unloading
More informationARDEX GUIDE SPECIFICATION ARDEX GS-4 Self-Leveling Repair Underlayment for Distressed Gypsum and Wood Subfloors
ARDEX GUIDE SPECIFICATION ARDEX GS-4 Self-Leveling Repair Underlayment for Distressed Gypsum and Wood Subfloors SECTION 03 54 13 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general provisions of
More informationE.MIX MOISTURE SEALER
E.MIX Super Fast Fix Fast setting, high performance, high strength, highly flexible, strong polymerized thin bed tile adhesive for interior and exterior wall tile fixing complied with C2FTE class of EN
More informationSECTION HYDRAULIC CEMENT UNDERLAYMENT
ARDEX GUIDE SPECIFICATION ARDEX V 1200 Self-Leveling Underlayment A Self-Leveling Underlayment that Consists of a Blend of Portland Cements, Other Hydraulic Cements and Polymers for Interior Applications
More informationSECTION RESINOUS FLOORING
SECTION 09705 PART I - GENERAL 1.01 DESCRIPTION A. Scope: Work of this Section includes all materials and installation necessary to provide resinous flooring system with integral cove base and top finish
More informationPROTECTO-CRETE 900/900SF
FEATURES PC-900 PC-900SF Excellent Chemical Resistance Excellent Wear Resistance Excellent Bond Strength to Concrete RECOMMENDED APPLICATIONS Tensile Bond Strength ASTM D-7234 Cohesive Failure Same of
More informationSECTION HYDRAULIC CEMENT UNDERLAYMENT
ARDEX GUIDE SPECIFICATION ARDEX LW Lightweight, Fast-Setting, Concrete Fill System Portland Cement-based Self-Leveling Underlayment for Interior Applications over Concrete Substrates SECTION 03 54 16 HYDRAULIC
More informationSECTION HYDRAULIC CEMENT UNDERLAYMENT
ARDEX GUIDE SPECIFICATION ARDEX K 520 Self-Leveling Concrete Topping Self-Leveling Topping for Indoor Fast-Track Resurfacing SECTION 03 54 16 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general
More informationARDEX GUIDE SPECIFICATION ARDEX K 22 F High Flow, Fiber Reinforced, Self-Leveling Underlayment
ARDEX GUIDE SPECIFICATION ARDEX K 22 F High Flow, Fiber Reinforced, Self-Leveling Underlayment SECTION 03 54 13 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general provisions of the Contract, and
More informationPRODUCT DATA SHEET Sikafloor -264
PRODUCT DATA SHEET 2-PART EPOXY ROLLER AND SEAL COAT DESCRIPTION is two part, economic, coloured epoxy resins. "Total solid epoxy composition acc. to the test method of Deutsche Bauchemie" USES may only
More informationSECTION EPOXY RESIN FLOORING WITH INTEGRAL COVE BASE
SECTION 09730 EPOXY RESIN FLOORING WITH INTEGRAL COVE BASE PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 03300 - Cast-in-Place Concrete. 2. 09000 - Patching and Finishes. 3. 09900 - Painting. 4.
More informationSECTION EPOXY FLOORING SYSTEMS
SECTION 09800 EPOXY FLOORING SYSTEMS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationBENTLEY ELEMENTS COLLECTION LVT
This document refers to the following products: Product Size Thickness Installation direction Seams treatment Elements Square See specifications 2.5mm 90 None Elements Plank See specifications 2.5mm Stair
More informationLiquid applied polyurea hybrid membrane
Product Data Sheet Edition 07/08/2008 Identification no: 02 06 07 01 001 0 000015 Sikalastic -842 BG Liquid applied polyurea hybrid membrane Product Description Sikalastic -842 BG is a two part, highly
More informationAppearance /Colours Resin - part A: transparent, liquid Hardener - part B: transparent, liquid Packaging. Pre-proportioned 5.
Product Data Sheet Edition 30/08/2012 Sikafloor -160 2-part solvent free epoxy primer & binder, modular Sikafloor system Construction Product Description Sikafloor -160 is a two part, low viscosity epoxy
More information