Postemergence herbicide for control of grass weeds in wheat and barley
|
|
- Clement Cannon
- 5 years ago
- Views:
Transcription
1 1951 Axial Mech 4/9/08 9:55 AM Page 1 PULL HERE TO OPEN GROUP 1 HERBICIDE Herbicide Postemergence herbicide for control of grass weeds in wheat and barley Active Ingredient: Pinoxaden* % Other Ingredients: 90.29% Total: % *CAS No Contains petroleum distillates. Axial Herbicide contains 0.83 lb. of pinoxaden active ingredient per gallon. KEEP OUT OF REACH OF CHILDREN. CAUTION See additional precautionary statements and directions for use inside booklet. EPA Reg. No Product of United Kingdom Formulated in the USA SCP 1199A-L1C gallons Net Contents EPA Est CAN-001
2 1951 Axial Mech 4/9/08 9:55 AM Page 3 If in eyes If on skin or clothing If swallowed If inhaled FIRST AID Hold eye open and rinse slowly and gently with water for minutes. Remove contact lenses, if present after the first 5 minutes, then continue rinsing eye. Call a poison control center or doctor for treatment advice. Take off contaminated clothing. Rinse skin immediately with plenty of water for minutes. Call a poison control center or doctor for treatment advice. Immediately call a poison control center or doctor. Do not induce vomiting unless told to do so by a poison control center or doctor. Do not give any liquid to the person. Do not give anything by mouth to an unconscious person. Move person to fresh air. If person is not breathing, call 911 or an ambulance, then give artificial respiration, preferably by mouth-to-mouth, if possible. Call a poison control center or doctor for further treatment advice. Have the product container or label with you when calling a poison control center or doctor or going for treatment. Note to Physician Contains petroleum distillates vomiting may cause aspiration pneumonia. HOT LINE NUMBER For 24 Hour Medical Emergency Assistance (Human or Animal) or Chemical Emergency Assistance (Spill, Leak, Fire, or Accident) Call PRECAUTIONARY STATEMENTS Hazards to Humans and Domestic Animals CAUTION Causes moderate eye irritation. Avoid contact with eyes, skin or clothing. Harmful if swallowed or absorbed through skin. Personal Protective Equipment (PPE) Some materials that are chemical resistant to this product are listed below. If you want more options, follow the instructions for Category A on an EPA chemical resistant category selection chart. continued... 3
3 1951 Axial Mech 4/9/08 9:55 AM Page 4 PRECAUTIONARY STATEMENTS (continued) Applicators and other handlers must wear: Long-sleeved shirt and long pants Shoes plus socks Chemical-resistant gloves, Category A, such as barrier laminate, butyl rubber 14 mils, nitrile rubber 14 mils, neoprene rubber 14 mils, polyethylene, polyvinyl chloride (PVC) 14 mils, or viton 14 mils Follow manufacturer s instructions for cleaning/maintaining PPE. If no such instructions for washables, use detergent and hot water. Keep and wash PPE separately from other laundry. Engineering Control Statements When handlers use closed systems, enclosed cabs, or aircraft in a manner that meets the requirements listed in the Worker Protection Standard (WPS) for agricultural pesticides [40 CFR (d)(4-6)], the handler PPE requirements may be reduced or modified as specified in the WPS. User Safety Recommendations Users should: Wash hands before eating, drinking, chewing gum, using tobacco, or using the toilet. Remove clothing/ppe immediately if pesticide gets inside. Then wash thoroughly and put on clean clothing. Remove PPE immediately after handling this product. Wash the outside of gloves before removing. As soon as possible, wash thoroughly and change into clean clothing. Environmental Hazards For terrestrial uses: Do not apply directly to water, to areas where surface water is present, or to intertidal areas below the mean high water mark. Do not contaminate water when disposing of equipment wash water or rinsate. Physical or Chemical Hazards Do not use or store near heat or open flame. CONDITIONS OF SALE AND LIMITATION OF WARRANTY AND LIABILITY NOTICE: Read the entire Directions for Use and Conditions of Sale and Limitation of Warranty and Liability before using this product. If the terms are not acceptable, return the product at once, unopened, and the purchase price will be refunded. 4
4 1951 Axial Mech 4/9/08 9:55 AM Page 5 The Directions for Use of this product must be followed carefully. It is impossible to eliminate all risks inherently associated with the use of this product. Crop injury, ineffectiveness or other unintended consequences may result because of such factors as manner of use or application, weather or crop conditions, presence of other materials or other influencing factors in the use of the product, which are beyond the control of SYNGENTA CROP PROTECTION, Inc. or Seller. To the extent permitted by applicable law, Buyer and User agree to hold SYNGENTA and Seller harmless for any claims relating to such factors. SYNGENTA warrants that this product conforms to the chemical description on the label and is reasonably fit for the purposes stated in the Directions for Use, subject to the inherent risks referred to above, when used in accordance with directions under normal use conditions. To the extent permitted by applicable law: (1) this warranty does not extend to the use of the product contrary to label instructions or under conditions not reasonably foreseeable to or beyond the control of Seller or SYNGENTA, and, (2) Buyer and User assume the risk of any such use. TO THE EXTENT PERMITTED BY APPLICABLE LAW, SYNGENTA MAKES NO WARRANTIES OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE NOR ANY OTHER EXPRESS OR IMPLIED WARRANTY EXCEPT AS WARRANTED BY THIS LABEL. To the extent permitted by applicable law, in no event shall SYNGENTA be liable for any incidental, consequential or special damages resulting from the use or handling of this product. TO THE EXTENT PERMITTED BY APPLICABLE LAW, THE EXCLUSIVE REMEDY OF THE USER OR BUYER, AND THE EXCLU- SIVE LIABILITY OF SYNGENTA AND SELLER FOR ANY AND ALL CLAIMS, LOSSES, INJURIES OR DAMAGES (INCLUDING CLAIMS BASED ON BREACH OF WARRANTY, CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE) RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT, SHALL BE THE RETURN OF THE PURCHASE PRICE OF THE PRODUCT OR, AT THE ELECTION OF SYNGENTA OR SELLER, THE REPLACEMENT OF THE PRODUCT. SYNGENTA and Seller offer this product, and Buyer and User accept it, subject to the foregoing Conditions of Sale and Limitation of Warranty and Liability, which may not be modified except by written agreement signed by a duly authorized representative of SYNGENTA. DIRECTIONS FOR USE It is a violation of federal law to use this product in a manner inconsistent with its labelling. Axial Herbicide should be used only in accordance with directions on this label or in separately published Syngenta supplemental labelling directions for this product. Do not apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be in the area during application. For any requirements specific to your State or Tribe, consult the agency responsible for pesticide regulation. 5
5 1951 Axial Mech 4/9/08 9:55 AM Page 6 AGRICULTURAL USE REQUIREMENTS Use this product only in accordance with its labelling and with the Worker Protection Standard, 40 CFR part 170. This Standard contains requirements for the protection of agricultural workers on farms, forests, nurseries, and greenhouses, and handlers of agricultural pesticides. It contains requirements for training, decontamination, notification, and emergency assistance. It also contains specific instructions and exceptions pertaining to the statements on this label about personal protective equipment (PPE) and restricted-entry interval. The requirements in this box only apply to uses of this product that are covered by the Worker Protection Standard. Do not enter or allow worker entry into treated areas during the restricted-entry interval (REI) of 48 hours. PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and that involves contact with anything that has been treated, such as plants, soil, or water is: Long-sleeved shirt and long pants Shoes plus socks Chemical-resistant gloves, Category A, such as barrier laminate, butyl rubber 14 mils, nitrile rubber 14 mils, neoprene rubber 14 mils, polyethylene, polyvinyl chloride (PVC) 14 mils, or viton 14 mils FAILURE TO FOLLOW THE DIRECTIONS FOR USE AND PRECAUTIONS ON THIS LABEL MAY RESULT IN CROP INJURY AND/OR POOR WEED CONTROL. GENERAL INFORMATION Axial Herbicide is a systemic, postemergence herbicide for the control of several grass weed species in all varieties of spring wheat (excluding durum), winter wheat, and barley. Axial Herbicide is rapidly absorbed by weed foliage and translocated to the growing points of leaves and stems where it inhibits the acetyl CoA carboxylase (ACCase) enzyme. Susceptible weed species generally stop growing within 48 hours of treatment, turn yellow within one to three weeks, and are completely controlled within three to five weeks. Level and rate of control depend on weed species, growing conditions, crop competition, and coverage. Thorough spray coverage of the plants is essential for consistent control. Although Axial Herbicide does not control broadleaf weeds, it can be tank mixed with a wide range of broadleaf herbicides to provide broad-spectrum one-pass weed control. It can also be tank mixed with Tilt Fungicide, Quilt Fungicide, and Warrior Insecticide with Zeon Technology. See the section entitled Tank Mixes of Axial Herbicide with Broadleaf Weed Herbicides, Fungicides, and Insecticides. Herbicides not approved on this label for tank mixing with Axial Herbicide may be applied sequentially. Always apply Axial Herbicide first and allow at least 4 days after application of Axial Herbicide before applying these herbicides sequentially. 6
6 1951 Axial Mech 4/9/08 9:55 AM Page 7 Weeds Controlled Axial Herbicide controls green foxtail, yellow foxtail, giant foxtail, wild oat, volunteer oat, barnyardgrass, Persian darnel, Italian (annual) ryegrass, canarygrass, wild proso millet, and windgrass. Use Rates Apply the specified rate of Axial Herbicide and the specified rate of Adigor Adjuvant using ground or aerial equipment, in a minimum of 5 gals. of water per acre (see Ground and Aerial Application Procedures section for additional information). WEEDS CONTROLLED A USE RATES Wild oat, Avena fatua Volunteer oat, Avena sativa Green foxtail, Setaria viridis Axial Herbicide oz./a + Yellow foxtail, Setaria glauca Giant foxtail, Setaria faberi Adigor Adjuvant 9.6 oz./a Italian (annual) ryegrass, Lolium mutiflorum Persian darnel, Lolium persicum Barnyardgrass, Echinochloa crus-galli Canarygrass, Phalaris spp. Wild proso millet, Panicum miliaceum Windgrass, Apera spp. AWhen tank mixing broadleaf herbicides, refer to Tank Mixes of Axial Herbicide with Broadleaf Weed Herbicides, Fungicides, and Insecticides section for exceptions and additional information on weeds controlled. Management of Resistant Weeds Axial Herbicide is a Group 1 herbicide (ACCase mode of action). Some naturally occurring populations of wild oats, green foxtail and Italian (annual) ryegrass have been identified as resistant to herbicides with the ACCase mode of action (herbicides with the same mode of action as Axial Herbicide, such as: Achieve, Assure II, Discover, Fusilade, Fusion, Hoelon, Poast, Prism, Puma, Select ). Selection of resistant biotypes, through repeated use of these herbicides in the same field, may result in control failures. A resistant biotype may be present if poor performance cannot be attributed to adverse weather conditions or improper application methods. If resistance is suspected, contact your local Syngenta representative for assistance. The following practices will delay selection for resistant populations of weeds: Apply postemergence herbicides to small, actively growing weeds. Ensure that good spray coverage is achieved with proper spray volumes and calibrated equipment. Use the full label rate of product with the recommended tank mix spray adjuvant. Avoid tank mixes that may cause antagonism and reduced weed control. Where possible, avoid the repeated use of herbicides with the same mode of action (i.e., same group number) in successive seasons either in cereal crops or rotational crops. Use a diverse crop/fallow rotation to extend the range of available herbicides and agronomic practices. Use cultivation, fertilizer regimens, seeding rates and row widths that enhance crop competitiveness. Prevent weed escapes from producing seed either in the crop or during fallow periods. 7
7 1951 Axial Mech 4/9/08 9:55 AM Page 8 Rotational Crop Restrictions The following crops may be planted at the specified interval following application of Axial Herbicide. Crop Wheat (including Durum) and Barley Leafy and Root Crops Other Cereal Grains and All Other Crops Rotational Interval 0 days 30 days 120 days APPLICATION PROCEDURES Timing of Application Apply Axial Herbicide to all varieties of spring wheat (excluding durum), winter wheat, and barley from the 2-leaf stage to pre-boot stage. Refer to the Crop Use Directions section for grazing and harvest restrictions. Precaution: Do not apply to a crop that is stressed by conditions such as frost, low fertility, drought, flooding, disease damage, or insect damage, as crop injury may result. When tank mixing with a broadleaf herbicide, insecticide or fungicide, always refer to the label of the tank mix partner prior to use. For optimum results, apply Axial Herbicide to actively growing weeds. An early application will maximize crop yields by reducing weed competition. Weed control following application of Axial Herbicide alone or in combination with broadleaf herbicides can be reduced or delayed under conditions of stress, such as drought, heat, insufficient fertility, flooding, and prolonged cool temperatures. Grass escapes or re-tillering may occur if application is made during prolonged conditions of stress. Optimum weed control will be obtained if application of Axial Herbicide is delayed until the conditions of stress have ended and weeds are once again actively growing. Weeds emerging after Axial Herbicide application will not be controlled. TIMING OF APPLICATION TO WEEDS Weed Leaves on Main Stem Tillers Persian Darnel 1 to 6-leaf stage on main stem Prior to emergence of the Volunteer Oat 4 th tiller Wild Oat Barnyardgrass 1 to 5-leaf stage on main stem For optimum control, apply Giant Foxtail prior to emergence of the Green Foxtail 3 rd tiller and while weeds Yellow Foxtail are actively growing. Italian (Annual) Ryegrass Canarygrass Wild Proso Millet Windgrass 8
8 1951 Axial Mech 4/9/08 9:55 AM Page 9 Rainfastness Axial Herbicide applied alone is not affected by rain falling 30 minutes or more after application. Ground and Aerial Application Procedures For best accuracy, calibrate the sprayer before use. Ground Applications Water Volume Use an application rate of 5 10 gals. of water per acre. Use 10 gals. of water per acre under dry conditions or dense weed populations. Application rates of greater than 10 gallons of water per acre should be avoided as reduced grass control may occur. Spray Nozzles 80 or 110 flat fan nozzles are recommended for optimum spray coverage. Nozzles must be uniformly spaced along the boom to provide accurate and uniform coverage. Point the nozzles forward in the direction of travel at an angle of 45 for optimum coverage of grass weeds. Follow the nozzle manufacturer s recommendations for pressure and screens. Do not use flood or hollow cone type nozzles. Screens Use a screen or strainer with 16-mesh or coarser on the suction side of the pump. Do not place a screen in the recirculation line unless using a roller or piston pump. Use 50-mesh or coarser screens between the pump and boom, and at the nozzles. Pressure psi at the nozzles. Lower pressure may be used with extended range or low pressure nozzles. Pump Must have capacity to maintain pressure (35-40 psi) and to maintain the product suspension through tank agitation. A centrifugal pump is recommended with an agitation rate of 20 gals./ minute/100 gals. tank size. Agitation must be maintained during mixing and spraying. Good weed coverage with the spray mixture is essential for optimum weed control results. Observe sprayer nozzles frequently during the spraying operation to ensure that the spray pattern is uniform. Avoid large spray overlaps which result in excessive rates in the overlap areas. Also, avoid application under conditions when uniform coverage cannot be obtained or when excessive spray drift may occur. To reduce spray drift, do not apply under windy conditions. Allow adequate distance between target area and desirable vegetation to prevent drift to nontarget areas. Boom height for broadcast overthe-top application should be based upon the free-standing height of the crop, not height above the soil surface, and should be at least 12 inches above the crop. AERIAL APPLICATIONS Apply Axial Herbicide in water using a minimum spray volume of 5 gals./a. Avoid application under conditions where uniform coverage cannot be obtained or where excessive spray drift may occur. Make applications at a maximum height of 10 ft. above the crop with low-drift nozzles at a maximum pressure of 40 psi and wind speed not exceeding 10 mph to help assure accurate application within the target area. Drift Management Avoiding spray drift at the application site is the responsibility of the applicator and the grower. The interaction of many equipment- and weather-related factors determines the potential for spray drift. The applicator and grower must consider the interaction of equipment and related factors to ensure that the potential for drift to sensitive non-target plants is minimal. 9
9 1951 Axial Mech 4/9/08 9:55 AM Page 10 The following drift management requirements must be followed to avoid off-target drift movement from aerial applications to agricultural field crops. These requirements do not apply to forestry applications, public health uses, or to applications using dry formulations. 1. The distance of the outermost nozzles on the boom must not exceed 3 /4 the length of the wingspan or rotor. 2. Nozzles must always point backward parallel with the air stream and never be pointed downward more than 45 degrees. Where states have more stringent regulations, they must be observed. The applicator should be familiar with and take into account the information covered in the Aerial Drift Reduction Advisory Information. Aerial Drift Reduction Advisory Information Information on Droplet Size The most effective way to reduce drift potential is to apply large droplets. The best drift management strategy is to apply the largest droplets that provide sufficient coverage and control. Applying larger droplets reduces drift potential, but will not prevent drift if applications are made improperly, or under unfavorable environmental conditions (see Wind, Temperature and Humidity, and Temperature Inversions). Controlling Droplet Size Volume Use high flow rate nozzles to apply the highest practical spray volume. Nozzles with higher rated flows produce larger droplets. Pressure Do not exceed the nozzle manufacturer s recommended pressures. For many nozzle types, lower pressure produces larger droplets. When higher flow rates are needed, use higher flow rate nozzles instead of increasing pressure. Number of Nozzles Use the minimum number of nozzles that provide uniform coverage. Nozzle Orientation Orienting nozzles so that the spray is released parallel to the airstream produces larger droplets than other orientations and is the recommended practice. Significant deflection from horizontal will reduce droplet size and increase drift potential. Nozzle Type Use a nozzle type that is designed for the intended application. With most nozzle types, narrower spray angles produce larger droplets. Consider using low-drift nozzles. Solid stream nozzles oriented straight back produce the largest droplets and the lowest drift. Boom Length For some use patterns, reducing the effective boom length to less than 3 /4 of the wingspan or rotor length may further reduce drift without reducing swath width. Application Height Applications should not be made at a height greater than 10 ft. above the top of the largest plants, unless a greater height is required for aircraft safety. Making applications at the lowest height that is safe reduces exposure of droplets to evaporation and wind. Swath Adjustment When applications are made with a crosswind, the swath will be displaced downwind. Therefore, on the up and downwind edges of the field, the applicator must compensate for this displacement by adjusting the path of the aircraft upwind. Swath adjustment distance should increase with increasing drift potential (higher wind, smaller drops, etc.). 10
10 1951 Axial Mech 4/9/08 9:55 AM Page 11 Wind Drift potential is lowest between wind speeds of 2-10 mph. However, many factors, including droplet size and equipment type, determine drift potential at any given speed. Application should be avoided below 2 mph due to variable wind direction and high inversion potential. Note: Local terrain can influence wind patterns. Every applicator should be familiar with local wind patterns and how they affect spray drift. Temperature and Humidity When making applications in low relative humidity, set up equipment to produce larger droplets to compensate for evaporation. Droplet evaporation is most severe when conditions are both hot and dry. Temperature Inversions Applications should not occur during a temperature inversion because drift potential is high. Temperature inversions restrict vertical air mixing, which causes small suspended droplets to remain in a concentrated cloud. This cloud can move in unpredictable directions due to the light variable winds common during inversions. Temperature inversions are characterized by increasing temperatures with altitude and are common on nights with limited cloud cover and light to no wind. They begin to form as the sun sets and often continue into the morning. Their presence can be indicated by ground fog; however, if fog is not present, inversions can also be identified by the movement of smoke from a ground source or an aircraft smoke generator. Smoke that layers and moves laterally in a concentrated cloud (under low wind conditions) indicates an inversion, while smoke that moves upward and rapidly dissipates indicates good vertical air mixing. Sensitive Areas This pesticide may only be applied when the potential for drift to adjacent sensitive areas, e.g., residential areas, bodies of water, non-target plants is minimal, (i.e., when the wind is blowing away from the sensitive area.) Avoid all direct or indirect contact (such as spray drift) of Axial Herbicide with crops other than those specified for treatment on this label, since injury may occur. Chemigation Do not apply this product through any type of irrigation system. MIXING PROCEDURES Mixing Instructions 1. Clean spray tank and half fill with clean water. Start agitation or bypass system. 2. If a broadleaf herbicide is to be used, add the product FIRST, prior to adding Axial Herbicide and agitate for 2-3 minutes. 3. Add correct amount of Axial Herbicide. 4. Agitate for 2-3 minutes. 5. Add correct amount of Adigor Adjuvant. 6. Agitate for 1-2 minutes before adding remainder of water and then maintain constant agitation. 7. After any break in spraying operations, agitate thoroughly before spraying again. 8. Use the spray solution as soon as it is prepared. 11
11 1951 Axial Mech 4/9/08 9:55 AM Page 12 Sprayer Cleanup Prior to using Axial Herbicide, ensure that the spray tank, lines and screens and filters are thoroughly clean. Thoroughly clean application equipment immediately after spraying Axial Herbicide. Ensure that all traces of the product are removed. The following directions are provided: 1. Drain and flush tank walls, boom, and all hoses for 10 minutes with clean water. Do not clean the sprayer near desirable vegetation, wells, or other water sources. 2. Remove the nozzles and screens and wash separately. 3. Dispose of all rinsates in accordance with state and local regulations. 4. If a broadleaf herbicide, insecticide, or fungicide tank mix partner is used, always check tank mix partner label for any additional cleanup procedures. CROP USE DIRECTIONS Wheat and Barley Axial Herbicide can be used on all varieties of spring wheat (excluding durum), winter wheat, and barley. Do not allow spray to drift to adjacent fields seeded to crops other than wheat or barley. Do not treat wheat or barley underseeded to forages. Avoid possible illegal residues: Make one application per crop season. Do not graze livestock or harvest forage for hay from treated wheat and barley for a minimum of 30 days following application. Do not harvest grain for 60 days following application. Do not apply both Discover and Axial products to the same crop in the same season. Wheat and barley straw may be fed to livestock 60 days after application. Tank Mixes of Axial Herbicide with Broadleaf Weed Herbicides, Fungicides, and Insecticides For broad-spectrum control of annual grass and broadleaf weeds, tank mix Axial Herbicide with one of the broadleaf herbicides or broadleaf herbicide combinations listed in the following table. Consult the label of the tank mix partner for a list of broadleaf weeds controlled, rates, timing, recropping restrictions, grazing interval restrictions, recommendations for specific weeds, directions for use, and precautions. Use in accordance with the most restrictive of label limitations and precautions. No label dosage rates should be exceeded. This product cannot be mixed with any other product whose label prohibits such a mixture. Table 1: For control of wild oat, volunteer oat, green foxtail, yellow foxtail, Italian (annual) ryegrass, and broadleaf weeds (refer to the broadleaf tank mix partner label for weeds controlled), use Axial Herbicide at 8.2 oz./a plus one of the following single or two-way broadleaf herbicide combinations. Broadleaf herbicide combinations other than those listed in the table below are not recommended. 12
12 1951 Axial Mech 4/9/08 9:55 AM Page 13 SELECT ONLY ONE BROADLEAF HERBICIDE TANK MIX COMBINATION LISTED IN THE TABLE BELOW Weeds Controlled by Axial Herbicide at 8.2 oz./a* Wild Volunteer Green Yellow Italian Broadleaf Herbicide Rate Oat Oat Foxtail Foxtail Ryegrass Affinity Tankmix A oz./a + C C C C -- MCPA Ester (assume pt./a 4 lb./gal) Ally A,F 0.1 oz./a C Amber A oz./a C C Bronate Advanced B,D pt./a C C C C C Buctril C,E pt./a C C C C C Buctril C,E + MCPA pt./a + C C C C C Ester (assume 4 lb./gal) pt./a Curtail M 1.75 pt./a C C C Finesse A oz./a C Harmony Extra A,G oz./a C C C C C Harmony Extra A,G oz./a + C C C C C MCPA Ester (assume pt./a 4 lb./gal.) Harmony GT A,H oz./a C C C C C Harmony GT A,H oz./a + C C C C C MCPA Ester (assume pt./a 4 lb./gal.) MCPA Ester (assume pt./a C C C C C 4 lb./gal.) Peak A oz./a C C Starane 0.67 pt./a C C C C C Starane + Bronate 0.67 pt./a + C C C C C Advanced B,D pt./a Starane + Harmony 0.67 pt./a + C C C -- C Extra A,G oz./a Starane pt./a + C C C -- C Harmony GT A,H oz./a Starane + Sword pt./a C C C C C WideMatch 1 pt./a C C C C C WideMatch + 1 pt./a + C C C C C Harmony GT A,H oz./a WideMatch + MCPA 1 pt./a + C C C C C Ester (assume 4 lb./gal) pt./a 13 footnotes on page 14...
13 1951 Axial Mech 4/9/08 9:55 AM Page 14 *C = Control A Addition of surfactants other than Adigor Adjuvant is not required. B Other equivalent products containing the active ingredients bromoxynil/mcpa esters may be used. Consult the specific product label for specified rates. C Other equivalent products containing the active ingredient bromoxynil may be used. Consult the specific product label for specified rates. DDo not exceed 0.8 pt./a of Bronate Advanced in a tank mix for control of Italian (annual) ryegrass, green foxtail, or yellow foxtail. EDo not exceed 1.25 pt./a of Buctril in a tank mix for control of Italian (annual) ryegrass, green foxtail, or yellow foxtail. F Ally XP may be used. G Harmony Extra XP may be used. HHarmony GT XP may be used. When tank mixing, add the broadleaf herbicide(s) to the spray tank first followed by Axial Herbicide, then add Adigor Adjuvant last. Precaution: Temporary crop injury may occur with tank mixes under extreme weather conditions or when the crop is suffering from stress due to inadequate or abnormally high moisture levels or extreme temperatures. Note: Tank mixing is not recommended with any chemical additives, pesticides, or fertilizers that are not recommended on this label or other Syngenta labelling as reduced annual grass control (antagonism) and/or crop injury may occur. Herbicides not approved on this label for tank mixing with Axial Herbicide may be applied sequentially. Always apply Axial Herbicide first and allow at least 4 days after application of Axial Herbicide before applying these herbicides sequentially. Tank Mix Application with Tilt Fungicide Axial Herbicide may be tank mixed with Tilt Fungicide for annual grass and disease control. Apply Axial Herbicide at 8.2 oz./a in a tank mix with Tilt at recommended use rates. Add Tilt to the tank first, followed by Axial Herbicide, then Adigor Adjuvant last. Refer to the Tilt label for specific use directions, application rates, restrictions, and a list of diseases controlled. Tank Mix Application with Quilt Fungicide Axial Herbicide may be tank mixed with Quilt Fungicide for annual grass control and early season disease suppression. Apply Axial Herbicide at 8.2 oz./a in a tank mix with Quilt Fungicide at 7 oz./a. Add Quilt to the tank first, followed by Axial Herbicide, then Adigor Adjuvant last. Refer to the Quilt label for specific use directions, application rates, restrictions, and a list of diseases suppressed and/or controlled. Note: under certain environmental conditions, tank mixes of Quilt Fungicide plus herbicides may cause crop injury. 14
14 1951 Axial Mech 4/9/08 9:55 AM Page 15 Tank Mix Application with Warrior Insecticide with Zeon Technology Axial Herbicide may be tank mixed with Warrior Insecticide with Zeon Technology for annual grass and insect control. Apply Axial Herbicide at 8.2 oz./a in a tank mix with Warrior Insecticide with Zeon Technology at recommended use rates. Add Warrior Insecticide with Zeon Technology to the tank first, followed by Axial Herbicide, then Adigor Adjuvant last. Refer to the Warrior Insecticide with Zeon Technology label for specific use directions, application rates, restrictions, and a list of insects controlled. Mixtures with Liquid Nitrogen Fertilizers Axial Herbicide may be mixed in a spray solution containing up to 50% liquid nitrogen fertilizer. Add Axial Herbicide to the water first followed by Adigor Adjuvant. Mix thoroughly, then add the liquid nitrogen fertilizer in an amount no greater than 50% of the final volume. Note: under certain environmental conditions, mixtures of liquid nitrogen fertilizers as a partial carrier may cause crop burn. When using Axial Herbicide with approved herbicide tank mix partners, consult the label of the partner product and follow any additional instructions or restrictions on that label which relate to mixture with liquid nitrogen fertilizers. STORAGE AND DISPOSAL Do not contaminate water, food, or feed by storage or disposal. Pesticide Storage Store in a cool, dry place. Do not store near seeds, fertilizers, or foodstuffs. Pesticide Disposal Pesticide wastes are toxic. Improper disposal of excess pesticides, spray mixture, or rinsate is a violation of Federal law. If these wastes cannot be disposed of by use according to label instructions, contact your State Pesticide or Environmental Control Agency, or the Hazardous Waste representative at the nearest EPA Regional Office for guidance. Container Disposal Do not reuse empty container. Triple rinse (or equivalent). Then offer for recycling or reconditioning, or puncture and dispose of in a sanitary landfill, or incineration, or, if allowed by state and local authorities, by burning. If burned, stay out of smoke. Bulk/Mini-Bulk When this container is empty replace cap and seal all openings that have been opened during use, and return the container to the point of purchase or to a designated location named at time of purchase of this product. The container must only be refilled with this pesticide product. DO NOT REUSE THE CONTAINER FOR ANY OTHER PURPOSE. Prior to refilling, inspect carefully for damage such as cracks, punctures, abrasions, worn-out threads and closure devices. Check for leaks after refilling and before transporting. Do not transport if this container is damaged or leaking. If the container is damaged, leaking or obsolete, contact Syngenta Crop Protection, Inc. at If not returned to the point of purchase or to a designated location, triple rinse emptied container and offer for recycling. Disposal of this container must be in compliance with state and local regulations. 15
15 1951 Axial Mech 4/9/08 9:55 AM Page 16 For minor spills, leaks, etc., follow all precautions indicated on this label and clean up immediately. Take special care to avoid contamination of equipment and facilities during cleanup procedures and disposal of wastes. In the event of a major spill, fire, or other emergency, call , day or night. CONTAINER IS NOT SAFE FOR FOOD, FEED, OR DRINKING WATER! Achieve, Adigor, Amber, Axial, Discover, Fusilade, Fusion, Peak, Quilt, Tilt, Warrior Insecticide with Zeon Technology, the Syngenta logo and the CP FRAME are trademarks of a Syngenta Group Company. Affinity, Ally, Assure II, Finesse, Harmony Extra, and Harmony GT trademarks of E.I. du Pont de Nemours and Company Buctril, Bronate, Hoelon, and Puma trademarks of Bayer CropScience Curtail M, Starane, and WideMatch trademarks of Dow AgroSciences, LLC Sword trademark of Platte Chemical Company Poast trademark of BASF Ag Products Prism and Select trademarks of Valent U.S.A. Corporation 2008 Syngenta Manufactured for: Syngenta Crop Protection, Inc. P.O. Box Greensboro, North Carolina SCP 1199A-L1C 0308 For non-emergency (e.g., current product information), call Syngenta Crop Protection at
16 1951 Tag Colors-Base Label 4/9/08 9:42 AM Page 2 BAR CODE # IS (01) LAST DIGIT IS CHECK DIGIT UCC/EAN 128 GROUP 1 HERBICIDE Herbicide Postemergence herbicide for control of grass weeds in wheat and barley Active Ingredient: Pinoxaden* % Other Ingredients: 90.29% Total: % *CAS No Contains petroleum distillates. Axial Herbicide contains 0.83 lb. of pinoxaden active ingredient per gallon. See directions for use inside booklet. AGRICULTURAL USE REQUIREMENTS Use this product only in accordance with its labelling and with the Worker Protection Standard, 40 CFR part 170. Refer to supplemental labelling under Agricultural Use Requirements in the Directions for Use section for information about this standrard. EPA Reg. No EPA Est CAN-001 Axial and the Syngenta logo are trademarks of a Syngenta Group Company Syngenta Manufactured for: Syngenta Crop Protection, Inc. P.O. Box Greensboro, North Carolina SCP 1199A-L1C gallons Net Contents KEEP OUT OF REACH OF CHILDREN. CAUTION Precautionary Statements Hazards to Humans and Domestic Animals CAUTION Causes moderate eye irritation. Avoid contact with eyes, skin or clothing. Harmful if swallowed or absorbed through skin. First Aid If in eyes: Hold eye open and rinse slowly and gently with water for minutes. Remove contact lenses, if present after the first 5 minutes, then continue rinsing eye. Call a poison control center or doctor for treatment advice. If on skin or clothing: Take off contaminated clothing. Rinse skin immediately with plenty of water for minutes. Call a poison control center or doctor for treatment advice. If swallowed: Immediately call a poison control center or doctor. Do not induce vomiting unless told to do so by a poison control center or doctor. Do not give any liquid to the person. Do not give anything by mouth to an unconscious person. If inhaled: Move person to fresh air. If person is not breathing, call 911 or an ambulance, then give artificial respiration, preferably by mouth-to-mouth, if possible. Call a poison control center or doctor for further treatment advice. Have the product container or label with you when calling a poison control center or doctor or going for treatment. Note to Physician: Contains petroleum distillates vomiting may cause aspiration pneumonia. HOT LINE NUMBER: For 24 Hour Medical Emergency Assistance (Human or Animal) or Chemical Emergency Assistance (Spill, Leak, Fire, or Accident) Call Environmental Hazards For terrestrial uses: Do not apply directly to water, to areas where surface water is present, or to intertidal areas below the mean high water mark. Do not contaminate water when disposing of equipment wash water or rinsate. Physical or Chemical Hazards Do not use or store near heat or open flame. Chemigation Do not apply this product through any type of irrigation system. Storage and Disposal Do not contaminate water, food, or feed by storage or disposal. Pesticide Storage: Store in a cool, dry place. Do not store near seeds, fertilizers, or foodstuffs. Pesticide Disposal: Pesticide wastes are toxic. Improper disposal of excess pesticides, spray mixture, or rinsate is a violation of Federal law. If these wastes cannot be disposed of by use according to label instructions, contact your State Pesticide or Environmental Control Agency, or the Hazardous Waste representative at the nearest EPA Regional Office for guidance. Container Disposal: Do not reuse empty container. Triple rinse (or equivalent). Then offer for recycling or reconditioning, or puncture and dispose of in a sanitary landfill, or incineration, or, if allowed by state and local authorities, by burning. If burned, stay out of smoke. CONTAINER IS NOT SAFE FOR FOOD, FEED, OR DRINKING WATER!
2.56 gallons CAUTION KEEP OUT OF REACH OF CHILDREN. SCP 1256A-L1C Net Contents GROUP 1 HERBICIDE
2249 Axial XL-2.56 gal.bklt 1/15/09 9:14 AM Page 1 PULL HERE TO OPEN GROUP 1 HERBICIDE Herbicide Postemergence herbicide for control of grass weeds in wheat and barley Active Ingredient: Pinoxaden*......................................................
IMPORTANT NOTICE. A single pass liquid postemergence herbicide for control of grass weeds in wheat (including Durum)
IMPORTANT NOTICE U.S. LABEL It is a violation of United States law to use this product in the United States in a manner inconsistent with its United States labeling Herbicide GROUP 1 HERBICIDE A single
For Control of Annual and Broadleaf Weeds In Non-Crop Areas. ACTIVE INGREDIENT: d-limonene 70% INERT INGREDIENTS:... 30% Total...
For Control of Annual and Broadleaf Weeds In Non-Crop Areas ACTIVE INGREDIENT: d-limonene 70% INERT INGREDIENTS:..... 30% Total...100% KEEP OUT OF REACH OF CHILDREN CAUTION EPA Reg. No. 82052-1 EPA Est.
Bloomtime. Biological FD Biopesticide
Bloomtime Biological FD Biopesticide BACTERIAL ANTAGONIST TO REDUCE THE SEVERITY OF FIRE BLIGHT CAUTION: KEEP OUT OF THE REACH OF CHILDREN ACTIVE INGREDIENT: Pantoea agglomerans strain E325; NRRL B-21856*..................................................
Bloomtime Biological FD Biopesticide
Bloomtime Biological FD Biopesticide ACTIVE INGREDIENT: Pantoea agglomerans strain E325; NRRL B-21856*... 7.0% Other ingredients: 93.0% 100.0% *MinimumPantoea agglomerans sps 1x10 10 cfu/g U.S. Patent
Herbicide GROUP 1 HERBICIDE. Active Ingredient: Clodinafop-propargyl (CAS No )...6.4% CAUTION. Skin Irritant
Herbicide GROUP 1 HERBICIDE A Single Pass Liquid Postemergence Herbicide For Control Of Grass Weeds In Wheat (Including Durum) Active Ingredient: Clodinafop-propargyl (CAS No. 105512-06-9)...6.4% OTHER
2.56 gallons Net Contents
GROUP 1 HERBICIDE PULL HERE TO OPEN Postemergence herbicide for control of grass weeds in wheat and barley Active Ingredient: Pinoxaden*............................................... 5.05% Other Ingredients:
Warden RTA. Fungicide. A seed treatment fungicide for control of certain seed-borne, soil-borne, and seedling diseases of soybeans
Warden RTA Fungicide A seed treatment fungicide for control of certain seed-borne, soil-borne, and seedling diseases of soybeans Active Ingredients: Mefenoxam*... 2.21% Fludioxonil**... 0.72% Other Ingredients:
2.5 gallons Net Contents KEEP OUT OF REACH OF CHILDREN. CAUTION SCP 945A-L1E
PULL HERE TO OPEN Fungicide Apron MAXX RTA + Moly is a ready-to-apply seed treatment fungicide for control of certain seed-borne, soil-borne, and seedling diseases of soybeans Active Ingredients: Mefenoxam*.............................................................
1 gallon U.S. Standard Measure
Herbicide Antidote For use as a seed dressing to protect grain or forage sorghum from the phyotoxic effects of S-metolachlor herbicide Active Ingredient: Fluxofenin (CAS No. 88485-37-4) 74.3% Other Ingredients:
Fungicide For Control of Certain Post-Harvest Diseases of Stone Fruits
PULL HERE TO OPEN Fungicide For Control of Certain Post-Harvest Diseases of Stone Fruits Active Ingredient: Fludioxonil (CAS No. 131341-86-1) 50.0% Other Ingredients: 50.0% Total: 100.0% Scholar is a 50%
2.5 Gallons C AV2 A SYSTEMIC FUNGICIDE AND BOOSTER OF PLANT DEFENSE MECHANISMS THAT HELPS CONTROL LISTED DISEASES OF
A SYSTEMIC FUNGICIDE AND BOOSTER OF PLANT DEFENSE MECHANISMS THAT HELPS CONTROL LISTED DISEASES OF TURFGRASS ACTIVE INGREDIENT: Mono- and di-potassium salts of phosphorous acid *...25.85% OTHER INGREDIENTS:...74.15%
For the Protection of Field and Sweet Corn Seed to discourage consumption by Black Birds Species and Crows. OTHER INGREDIENTS. 2.
24(c) Special Local Need Registration SLN VA 120001 (For Distribution and Use Only Within the State of Virginia) This SLN expires and must not be used or distributed after July 1, 2020 Avipel Hopper Box
Fungicide. SCP 889C-L1C gallons Net Contents
GROUP 1 FUNGICIDE PULL HERE TO OPEN Fungicide Active Ingredient: Thiabendazole*:............................................ 42.3% Other Ingredients: 57.7% Total: 100.0% *CAS No.148-79-8 Alumni is a suspension
INCENTIVE RTA. Fungicide. A seed treatment for control of diseases of wheat
Page 1 of 6 INCENTIVE RTA Fungicide A seed treatment for control of diseases of wheat Active Ingredients: Difenoconazole (CAS No. 119446-68-3)...3.21% (R)-[(2,6-dimethylphenyl)-methoxyacetylamino]- propionic
Restricts wavelengths of sunlight to control algae and aquatic vegetation and also colors the water blue.
ADMIRAL Liquid Restricts wavelengths of sunlight to control algae and aquatic vegetation and also colors the water blue. ACTIVE INGREDIENTS: Acid Blue 9... 15.31% Acid Yellow 23... 1.00% OTHER INGREDIENTS:...
FOR USE ON SUNFLOWER SEED TO BE EXPORTED ONLY
GROUP 12 FUNGICIDE FOR USE ON SUNFLOWER SEED TO BE EXPORTED ONLY Fungicide A seed treatment product for protection against Fusarium, Rhizoctonia, Helminthosporium, Aspergillus and Penicillium species causing
Postemergence herbicide for control of annual grass and broadleaf weeds in wheat and barley.
GROUP 1 4 HERBICIDES PULL HERE TO OPEN Postemergence herbicide for control of annual grass and broadleaf weeds in wheat and barley. Active Ingredient: Pinoxaden*:.........................................
For suppression of Downy Brome (cheatgrass), Medusahead, Japanese Brome, and Jointed Goatgrass on Wheat, Barley, Triticale, Oats, and Rangeland.
REV 05/16 B0 For suppression of Downy Brome (cheatgrass), Medusahead, Japanese Brome, and Jointed Goatgrass on Wheat, Barley, Triticale, Oats, and Rangeland. ACTIVE INGREDIENT: Pseudomonas fluorescens,
Fungicide A seed treatment for the control of listed fungal diseases of field corn, sweet corn and popcorn.
PULL HERE TO OPEN Fungicide A seed treatment for the control of listed fungal diseases of field corn, sweet corn and popcorn. Active Ingredients: Fludioxonil*...............................................
CAUTION. KEEP OUT OF REACH OF CHILDREN Read entire label for additional precautionary statements. EPA Reg. No
Coastal AgroBusiness, Inc. Product Label ACTIVE INGREDIENT n-decanol (Fatty Alcohol C 10 ) 79.0% INERT INGREDIENTS 21.0% TOTAL 100.0% Weight of Active Ingredients: 5.74 lbs. per gallon CAUTION KEEP OUT
GROUP 3 12 FUNGICIDES
GROUP 3 12 FUNGICIDES PULL HERE TO OPEN Fungicide Active Ingredients: Fludioxonil:*......................................... 21.7% Propiconazole:**...................................... 9.3% Other Ingredients:
Broad-spectrum seed treatment fungicide for control of seed and seed borne diseases.
GROUP 4 11 12 FUNGICIDES Fungicide Broad-spectrum seed treatment fungicide for control of seed and seed borne diseases. Active Ingredients: Azoxystrobin 1 :................................... 3.20% Fludioxonil
Fire Ant Control CAUTION. with Acephate KEEP OUT OF REACH OF CHILDREN
PEEL FROM CORNER OF BOOKLET If swallowed FIRST AID Contains an organophosphate that inhibits cholinesterase. Call a poison control center or doctor immediately for treatment advice. Do not induce vomiting
Fungicide Broad-spectrum seed treatment fungicide for control of seed and seed borne diseases.
GROUP 4 11 12 FUNGICIDES Fungicide Broad-spectrum seed treatment fungicide for control of seed and seed borne diseases. Active Ingredients: Azoxystrobin 1 :...................... 3.20% Fludioxonil 2 :.......................
POTATO SEED TREATER 6%
POTATO SEED TREATER 6% A FUNGICIDE FOR THE PROTECTION OF POTATO SEED PIECES AGAINST CERTAIN PLANT DISEASES. ACTIVE INGREDIENTS: BY WEIGHT Mancozeb: A coordination product of zinc ion and manganese ethylene
KEEP OUT OF REACH OF CHILDREN CAUTION. See additional precautionary statements elsewhere on this label.
A seed treatment that Suppresses Nematode Egg Production Increases Root Mass, Plant Stamina and Vigor Enhances Yield FOR USE ONLY BY COMMERCIAL SEED TREATMENT FACILITIES Wettable Dry Granule ACTIVE INGREDIENT:
A seed treatment product for suppression of certain diseases of potatoes.
Fungicide A seed treatment product for suppression of certain diseases of potatoes. Active Ingredients: Fludioxonil (CAS No. 131341-86-1)........................ 0.50% Mancozeb (CAS No. 8018-01-7)..........................
KEEP OUT OF REACH OF CHILDREN CAUTION NOT A PLANT FOOD INGREDIENT Active Ingredient: 9,10-Anthraquinone
24(c) Special Local Need Registration SLN NJ- 130002 (For Distribution and Use Only Within the State of New Jersey) This SLN expires and must not be used or distributed after August 31, 2019 Avipel Liquid
N-Hibit. Gold CST CAUTION
Seed Treatment A seed treatment that Suppresses Nematode Egg Production Increases Root Mass, Plant Stamina and Vigor Enhances Yield N-Hibit FOR USE ONLY BY COMMERCIAL SEED TREATMENT FACILITIES Gold CST
Plant growth regulator solution for use on apples, pears and cherries KEEP OUT OF REACH OF CHILDREN
Plant growth regulator solution for use on apples, pears and cherries Active Ingredient: N-(phenylmethyl)-1H-purine-6-amine... 9.51% Other Ingredients:... 90.49% Total:... 100.00% KEEP OUT OF REACH OF
Avipel Liquid Sunflower Seed Treatment
24(c) Special Local Need Registration SLN SD 130005 (For Distribution and Use Only Within the State of South Dakota) This SLN expires and must not be used or distributed after July 1, 2015 Avipel Liquid
Headline SBR Fungicide
This labeling is effective for distribution and use on soybeans grown in the state of Illinois until November 10, 2007 only under the quarantine emergency exemption pursuant to Section 18 of FIFRA as amended.
EVEREST 70% WATER DISPERSIBLE GRANULAR HERBICIDE CAUTION
Page 1 of 5 SUPPLEMENTAL LABELING FOR DISTRIBUTION AND USE ONLY WITHIN THE STATE OF IDAHO EVEREST 70% WATER DISPERSIBLE GRANULAR HERBICIDE EPA Reg. No. 66330-49 EPA For Application on Kentucky Bluegrass
Fungicide. 2 gallons Net Contents KEEP OUT OF REACH OF CHILDREN. CAUTION SCP 1451A-L1A
PULL HERE TO OPEN Fungicide A systemic fungicide for the control of diseases caused by Pythium spp. and other pathogens on turf of golf courses. Active Ingredient: Potassium Phosphite*.............................................................
KEEP OUT OF REACH OF CHILDREN. CAUTION
PULL HERE TO OPEN GROUP 4 11 12 FUNGICIDES COTTON SEED TREATMENT FUNGICIDE FUNGICIDE Broad-spectrum seed treatment fungicide for control of seed and seed borne diseases in cotton. ACTIVE INGREDIENTS: Azoxystrobin
Avipel Hopper Box (dry) Corn Seed Treatment
24(c) Special Local Need Registration SLN ID - 180008 (For Distribution and Use Only Within the State of Idaho) This SLN expires and must not be used or distributed after December 31, 2019 Avipel Hopper
REPAR STREPTOMYCIN 50
REPAR STREPTOMYCIN 50 AGRICULTURAL STREPTOMYCIN For control of halo blight of beans seed treatment (only in commercial seed treatment plants) and control of fire blight in apples and pears ACTIVE INGREDIENT
d-limonene SURFACTANT SPREADER ACTIVATOR PRINCIPAL FUNCTIONING AGENTS: Isoparaffinic hydrocarbons, d-limonene and Ethoxylated octylphenols...
d-limonene SURFACTANT SPREADER ACTIVATOR PRINCIPAL FUNCTIONING AGENTS: Isoparaffinic hydrocarbons, d-limonene and Ethoxylated octylphenols...100% Contains petroleum distillates. CA Reg. No. 1212-50001-AA
AV-1011 Rice Seed Treatment
AV-1011 Rice Seed Treatment For the protection of Rice Seed against consumption by Blackbirds. ACTIVE INGREDIENT 9,10-Anthraquinone....50% OTHER INGREDIENTS 50% Total 100% KEEP OUT OF REACH OF CHILDREN
FOR DISTRIBUTION AND USE ONLY WITHIN THE STATE OF COLORADO (MESA COUNTY ONLY)
FOR DISTRIBUTION AND USE ONLY WITHIN THE STATE OF COLORADO (MESA COUNTY ONLY) ATTENTION It is a violation of Federal law to use this product in a manner inconsistent with its labeling. Follow all applicable
Avipel Liquid Seed Treatment
24(c) Special Local Need Registration SLN WI - 130004 (For Distribution and Use Only Within the State of Wisconsin) This SLN expires and must not be used or distributed after July 1, 2015 Avipel Liquid
ORGANOSILICONE SURFACTANT
ORGANOSILICONE SURFACTANT Principal Functioning Agents: Polysiloxane polyether copolymer, Polyether.........100% TOTAL............................................100% CA Reg. No. 34704-50054 WA Reg. No.
SPECIMEN. ORGANOSILICONE SURFACTANT Principal Functioning Agents: Polysiloxane polyether copolymer...100% TOTAL...100% CA Reg. No.
ORGANOSILICONE SURFACTANT Principal Functioning Agents: Polysiloxane polyether copolymer..................100% TOTAL............................................100% CA Reg. No. 34704-50054 SLITHER 0.5GL/D2607
Broad-spectrum seed treatment fungicide for control of seed and seed borne diseases.
2118 DynastyCST-15gal.bklt 7/31/08 2:01 PM Page 1 PULL HERE TO OPEN GROUP 4 11 12 FUNGICIDES Fungicide Broad-spectrum seed treatment fungicide for control of seed and seed borne diseases. Active Ingredients:
KEEP OUT OF REACH OF CHILDREN CAUTION
ACTIVE INGREDIENT*: Mepiquat-chloride: N,N-dimethylpiperidinium chloride.................................. 23.6% Other Ingredients:............................................................... 76.4%
ACTIVE INGREDIENT: Natamycin % OTHER INGREDIENTS % Total % CAUTION
Zivion M Liquid Suspension Formulation - For Agricultural Use Only For use to control Dry Bubble Disease caused by Verticillium fungicola in enclosed mushroom production facilities ACTIVE INGREDIENT: Natamycin...
CAUTION. KEEP OUT OF REACH OF CHILDREN WARNING/AVISO Read entire label for additional precautionary statements.
Coastal AgroBusiness, Inc. Product Label ACTIVE INGREDIENTS n-octanol (Fatty Alcohol C 8) 35.5 % n-decanol (Fatty Alcohol C 10 ) 49.5 % INERT INGREDIENTS 15.0% Total 100% Weight of Active Ingredients:
AF Protects fruit from the various effects of ethylene. KEEP OUT OF REACH OF CHILDREN CAUTION FIRST AID
59075-2_book_art 1/20/14 1:24 PM Page 1 AF-2005 Protects fruit from the various effects of ethylene. ACTIVE INGREDIENT: 1-Methylcyclopropene... 0.8% OTHER INGREDIENTS*:... 99.2% *Contains petroleum distillates
Mycostop Biofungicide EPA Reg. No
Registrant Container Sizes 0.035, 0.176 and 0.88 oz. (1, 5 and 25 g) Verdera Oy Mycostop Biofungicide Container Type Plastic pouch in paperbag Address Riihitontuntie 14 A; P.O. Box 1; 02201 Espoo, Finland
6 X 2.5 ounce packets 15 ounces Total Net Weight Per Box. Insecticide KEEP OUT OF REACH OF CHILDREN. CAUTION SCP 913B-L1G
GROUP 9B INSECTICIDE PULL HERE TO OPEN Insecticide For control of aphids and whiteflies on landscape ornamentals, field-grown ornamentals, container-grown ornamentals, nonbearing fruit and nut trees in
LENTIL - ANNUAL WEEDS
LENTIL - ANNUAL WEEDS General Information Restrictions and Limitations - Maximum seasonal application rate - Refer to the Use-specific Information section of the label. - Preharvest interval (PHI) - Refer
CAUTION. For MEDICAL And TRANSPORTATION Emergencies ONLY Call 24 Hours A Day For PRODUCT USE Information Call FIRST AID
A Biological Agent for the Protection of Plant Roots Against Plant Parasitic Nematodes on Turf, Residential and Commercial Lawns, Sod Farms, Sports Fields and Golf Courses (Greens, Tees, Fairways and Roughs)
Harvista 1.3 SC. Protects fruit crops from the various effects of ethylene. KEEP OUT OF REACH OF CHILDREN CAUTION
Harvista 1.3 SC Protects fruit crops from the various effects of ethylene. ACTIVE INGREDIENT: 1-Methylcyclopropene.1.3% OTHER INGREDIENTS: 98.7% TOTAL: 100.0% Produced for: AgroFresh Inc. 400 Arcola Road,
A SEED TREATMENT CHEMICAL FOR CONTROL OF SEED ROT AND DAMPING-OFF DISEASES OF CERTAIN CROPS
OPEN HERE A SEED TREATMENT CHEMICAL FOR CONTROL OF SEED ROT AND DAMPING-OFF DISEASES OF CERTAIN CROPS ACTIVE INGREDIENTS: Metalaxyl: N-(2,6-dimethylphenyl)-N-(methoxyacetyl)alanine methyl ester... 28.35%
RESTRICTED USE PESTICIDE
[LEFT PANEL] RESTRICTED USE PESTICIDE DUE TO ACUTE HAZARDS TO THE EYE AND SKIN AND TO NON-TARGET ORGANISMS, NEED FOR HIGHLY SPECIALIZED APPLICATOR TRAINING, AND NEED FOR SPECIALIZED EQUIPMENT. ONLY FOR
FIFRA Section 18 Crisis Exemption
FIFRA Section 18 Crisis Exemption FOR DISTRIBUTION AND USE ON CORN SEED IN THE STATE OF FLORIDA ONLY DURING 2011 PURSUANT TO SECTION 18 OF FIFRA, AS AMENDED Avipel Liquid Seed Treatment Effective 03-14,
Mepiquat Chloride 4.2% Liquid
Mepiquat Chloride 4.2% Liquid PLANT REGULATOR ACTIVE INGREDIENT: % BY WT. Mepiquat Chloride*: N,N-dimethylpiperidinium chloride............... 4.2% OTHER INGREDIENTS:........................... 95.8% TOTAL..........................................
RESTRICTED USE PESTICIDE
[LEFT PANEL] RESTRICTED USE PESTICIDE DUE TO ACUTE HAZARDS TO THE EYE AND SKIN AND TO NON-TARGET ORGANISMS, NEED FOR HIGHLY SPECIALIZED APPLICATOR TRAINING, AND NEED FOR SPECIALIZED EQUIPMENT. ONLY FOR
DURING 2011 PURSUANT TO SECTION 18 OF FIFRA, AS AMENDED AV-1011
FIFRA Section 18 FOR DISTRIBUTION AND USE ON RICE SEED IN THE STATE OF Louisiana ONLY DURING 2011 PURSUANT TO SECTION 18 OF FIFRA, AS AMENDED AV-1011 Bird Repellent for Rice Seed Effective April 21, 2011
Fungicide. 2.5 gallons Net Contents CAUTION. A seed treatment for control of diseases of barley, cotton, sweet corn, wheat and triticale
PULL HERE TO OPEN Fungicide A seed treatment for control of diseases of barley, cotton, sweet corn, wheat and triticale Active Ingredients: Difenoconazole:* 7.73% Mefenoxam** 1.93% Other Ingredients: 90.34%
MECURIA CAUTION STORAGE AND DISPOSAL NET CONTENTS: 1 GALLON 44601AL0041. Fungicide KEEP OUT OF REACH OF CHILDREN CAUTION
74094 Mecuria (1g) BL 3/10/14 1:11 PM Page 1 NET CONTENTS: 1 GALLON 44601AL0041 MECURIA Fungicide ACTIVE INGREDIENT: Thiabendazole: 2-(4-thiazolyl)benzimidazole*............. 42.3% OTHER INGREDIENTS..............................
CAUTION PULL HERE TO OPEN GROUP 21 FUNGICIDE
GROUP 21 FUNGICIDE PULL HERE TO OPEN Plant Activator Active Ingredient: Acibenzolar-S-methyl: Benzo (1,2,3) thiadiazole-7- carbothioic acid-s-methyl ester*... 50.0% Other Ingredients: 50.0% Total: 100.0%
For control of certain insect pests infesting various cotton
PULL HERE TO OPEN TM Insecticide For control of certain insect pests infesting various cotton Active Ingredient: Thiamethoxam (CAS No. 153719-23-4).................... 25.0% Other Ingredients: 75.0% Total:
KEEP OUT OF REACH OF CHILDREN DANGER PELIGRO
ETHREL brand Ethephon Plant Growth Regulator For Pineapple and Sugarcane FOR COMMERCIAL OR AGRICULTURAL USE ONLY. NOT FOR RESIDENTIAL USE For Flower induction and Maturity Concentration in Pineapple For
For MEDICAL And TRANSPORTATION Emergencies ONLY Call 24 Hours A Day For PRODUCT USE Information Call BAYER ( )
PROCEED CONCENTRATE Fungicide ACTIVE INGREDIENTS: Prothioconazole: 2-[2-(1- Chlorocylocpropyl)-3-(2-chlorophenyl)-2-hydroxypropyl]- 1,2- dihydro-3h-1,2,4-triazole-3-thione 6.88% Tebuconazole: (Alpha-[2-(4-chlorophenyl)ethyl]-alpha-(1,1-dimethylethyl)-1H-1,2,4-triazole-1-
Cryolite: Sodium aluminofluoride* % OTHER INGREDIENTS % Total 100.0% *Fluorine expressed as elemental...50%
Prokil Cryolite 96 ACTIVE INGREDIENT: % by Wt. Cryolite: Sodium aluminofluoride*... 96.0% OTHER INGREDIENTS... 4.0% Total 100.0% *Fluorine expressed as elemental...50% KEEP OUT OF REACH OF CHILDREN CAUTION
Sorghum Herbicide Protectant. Use as a seed treatment to protect grain or forage sorghum from herbicide injury caused by Metolachlor or S-metolachlor
SorPro 940 ES Sorghum Herbicide Protectant Use as a seed treatment to protect grain or forage sorghum from herbicide injury caused by Metolachlor or S-metolachlor ACTIVE INGREDIENT: Fluxofenim (CAS No.
PRINCIPAL FUNCTIONING AGENTS: Paraffin Base Petroleum Oil 83.0% Surfactant Blend % TOTAL 100.0% KEEP OUT OF REACH OF CHILDREN
CROP OIL CONCENTRATE PRINCIPAL FUNCTIONING AGENTS: %BY WT. Paraffin Base Petroleum Oil 83.0% Surfactant Blend..... 17.0% TOTAL 100.0% Surfactant Content... 17.0% Minimum Unsulfonated Residue... 92.0% KEEP
FLOWABLE INSECTICIDE. Controls darkling beetles adults and larvae Time Saving Band Treatment Flexible application for any poultry operation
Dominion 4L FLOWABLE INSECTICIDE Controls darkling beetles adults and larvae Time Saving Band Treatment Flexible application for any poultry operation ACTIVE INGREDIENT % BY WT. Imidacloprid; 1-[(6-Chloro-3-pyridinyl)methyl]-N-nitro-2-
TM Embrace 3.6L Fungicide for control of specified diseases on peanuts and grasses grown for seed.
TM Embrace 3.6L Fungicide for control of specified diseases on peanuts and grasses grown for seed. ACTIVE INGREDIENT: Tebuconazole, alpha-[2-(4-chlorophenyl)ethyl]-alpha-(1,1-dimethylethyl)-1h-1,2,4-triazole-1-ethanol...
Insecticide. Fire Ant Bait
PULL HERE TO OPEN Fire Ant Bait Insecticide For control of imported fire ants, bigheaded ants, pavement ants, and turfgrass ants on lawns, recreational areas, golf courses and fenced pastures grazed by
ADMIRE. 240 Flowable Systemic Insecticide. GUARANTEE: Imidacloprid g/l READ THE LABEL AND LEAFLET BEFORE USING KEEP OUT OF REACH OF CHILDREN
SUPPLEMENTAL LABEL FOR CONTROL OF WESTERN CHERRY FRUIT FLY AND BLACK CHERRY FRUIT FLY ON SWEET AND SOUR CHERRY IN BRITISH COLUMBIA AND ONTARIO ONLY ADMIRE 240 Flowable Systemic Insecticide GROUP 4 INSECTICIDE
CAUTION. 1 Gallon KEEP OUT OF REACH OF CHILDREN
Net Contents: 1 Gallon ACTIVE INGREDIENT: Spinosad (CAS Number 131929-60-7)... 8.66% INERT INGREDIENTS:... 91.34% TOTAL: 100.00% EPA Reg. No. 264-995 KEEP OUT OF REACH OF CHILDREN CAUTION FOR ADDITIONAL
2.34 gallons Net Contents
100-1632_Axial Bold Herbicide_20180525_205_100-2_.pdf PINOXADEN GROUP 1 HERBICIDE FENOXAPROP-P-ETHYL GROUP 1 HERBICIDE PULL HERE TO OPEN Postemergence herbicide for control of grass weeds in wheat and
CAUTION. KEEP OUT OF REACH OF CHILDREN Read entire label for additional precautionary statements. Manufactured By: Coastal AgroBusiness, Inc.
Coastal AgroBusiness, Inc. Product Label Active Ingredient: (% by weight) Maleic Hydrazide, potassium salt (CAS No. 28382-15-2) (1,2-dihydro-3,6-pyridazinedione, potassium salt)...21.7%* Inert Ingredients:.......78.3%
Fungicide Seed Treatment For Corn
OPEN HERE Fungicide Seed Treatment For Corn Active Ingredient: Ipconazole (CAS No. 125225-28-7)... 40.7% Other Ingredients:... 59.3% Total: 100.0% Contains 3.77 lb ai ipconazole/gallon EPA Reg. No. 264-988-524
Orthene 97 ST Soluble Insecticide
Orthene 97 ST Soluble Insecticide Active Ingredient By Weight *Acephate...97.4 % Inert Ingredients...2.6 % Total...100.0 % *O,S-Dimethyl acetylphosphoramidothioate U.S. Patent. No. 6,013,272 If swallowed:
MERGE ADJUVANT. A blend of surfactant with petroleum hydrocarbons for application with various herbicides
Approved Master Copy (renewal [2009-3091]), September 29, 2009 MERGE ADJUVANT A blend of surfactant with petroleum hydrocarbons for application with various herbicides COMMERCIAL (AGRICULTURAL) GUARANTEE:
FOR DISTRIBUTION AND USE ONLY WITHIN THE STATES OF COLORADO, IDAHO, MONTANA, NEVADA, OREGON, UTAH AND WASHINGTON
FOR DISTRIBUTION AND USE ONLY WITHIN THE STATES OF COLORADO, IDAHO, MONTANA, NEVADA, OREGON, UTAH AND WASHINGTON A locally systemic fungicide for the control of scab, powdery mildew and rusts on apples;
FLOWABLE TURF FUNGICIDE
FLOWABLE TURF FUNGICIDE ACTIVE INGREDIENT: (% by weight) Pentachloronitrobenzene (PCNB)... 40.0% INERT INGREDIENTS:... 60.0% TOTAL:... 100.0% Contains 4 lbs. of Pentachloronitrobenzene per U.S. gallon
KEEP OUT OF REACH OF CHILDREN CAUTION
ACTIVE INGREDIENT: 1-Napthaleneacetamide... 8.4% INERT INGREDIENTS:... 91.6% TOTAL:... 100.0% KEEP OUT OF REACH OF CHILDREN CAUTION FIRST AID If on skin or clothing: Take off contaminated clothing. Rinse
Front Booklet. Plant growth regulator solution for use on apples, pears and cherries. Active Ingredient: N-(phenylmethyl)-1Hpurine-6-amine
FINE AMERICAS Exilis 9.5 SC PGR 1 quart DATE: 1.8.16 Booklet: w x h closed 6.75" w x h open Base: 4" w x h Front Booklet Pantone 1817 Pantone 369 Plant growth regulator solution for use on apples, pears
Broad-spectrum seed treatment fungicide for control of seed and seed borne diseases in cotton.
Broad-spectrum seed treatment fungicide for control of seed and seed borne diseases in cotton. Active Ingredients: Azoxystrobin 1... 5.24% Fludioxonil 2..... 0.87% Mefenoxam 3. 2.62% Difenoconazole 4...
Golden Eagle TM Turf Fungicide
2008-5020 11-FEB-2011 (Container) Golden Eagle TM Turf Fungicide GROUP 3 FUNGICIDE COMMERCIAL GRANULAR READ THE LABEL AND BOOKLET BEFORE USING KEEP OUT OF REACH OF CHILDREN GUARANTEE: Myclobutanil 0.39%
Sale, use and distribution of this product in Nassau and Suffolk counties in the state of New York is prohibited.
Sale, use and distribution of this product in Nassau and Suffolk counties in the state of New York is prohibited. GROUP 4A INSECTICIDE Insecticide For systemic control of insect pests on ornamental plants
FOR DISTRIBUTION AND USE ONLY WITHIN THE STATE OF OREGON BEACON
FOR DISTRIBUTION AND USE ONLY WITHIN THE STATE OF OREGON BEACON EPA Reg. No. 100-705 This label valid until December 31, 2017 or until otherwise amended, withdrawn, cancelled, or suspended. For Weed Control
AXIAL 100EC Herbicide
Approved Pamphlet AXIAL 100 EC 28642 07-07-19 Page 1 of 9 GROUP 1 HERBICIDE HERBICIDE AXIAL 100EC Herbicide AGRICULTURAL A post emergence herbicide for control of wild oats, green foxtail, yellow foxtail,
Insecticide. 25 pounds Net Weight
Sale, use and distribution of this product in Nassau and Suffolk counties in the state of New York is prohibited. GROUP 4A INSECTICIDE Insecticide For systemic control of insect pests on ornamental plants
RESTRICTED USE PESTICIDE DUE TO TOXICITY TO FISH AND AQUATIC ORGANISMS. For Use to Control Insects on Field Corn, Popcorn, Seed Corn and Sweet Corn
RESTRICTED USE PESTICIDE DUE TO TOXICITY TO FISH AND AQUATIC ORGANISMS FOR RETAIL SALE TO AND USE ONLY BY CERTIFIED APPLICATORS, OR PERSONS UNDER THEIR DIRECT SUPERVISION, AND ONLY FOR THOSE USES COVERED
Fungicide. 50 pounds Net Weight
GROUP 12 M3 FUNGICIDES Fungicide A seed treatment product for suppression of certain diseases of potatoes. Active Ingredients: Fludioxonil 1 :.................................... 0.50% Mancozeb 2 :.....................................
IAP 470 DORMANT SPRAY OIL
IAP 470 DORMANT SPRAY OIL Active Ingredient: Mineral Oil*...98.5 % Inert Ingredients:... 1.5 % TOTAL...100.0 % *Contains petroleum distillates Minimum Unsulfonated Residue...93.5 % EPA Reg. No. 71058-2
Headline. Supplemental Labeling. fungicide. Precautionary Statements Endangered Species Concerns. For use in Soybeans. EPA Reg. No.
Headline fungicide Supplemental Labeling For use in Soybeans EPA Reg. No. 7969-186 Precautionary Statements Endangered Species Concerns The use of any pesticide in a manner that may kill or otherwise harm
FIFRA Section 24(c) Special Local Need Label FOR DISTRIBUTION AND USE ONLY WITHIN OREGON. EPA Reg. No EPA SLN No.
CLETHODIM Group 1 HERBICIDE FIFRA Section 24(c) Special Local Need Label FOR DISTRIBUTION AND USE ONLY WITHIN OREGON SELECT MAX Herbicide with Inside Technology TM EPA Reg. No. 59639-132 For control of
MERGE ADJUVANT EMULSIFIABLE CONCENTRATE. A blend of surfactant with petroleum hydrocarbons for application with various herbicides
MERGE ADJUVANT EMULSIFIABLE CONCENTRATE A blend of surfactant with petroleum hydrocarbons for application with various herbicides COMMERCIAL (AGRICULTURAL) GUARANTEE: Surfactant blend...... 50% Solvent
MERGE ADJUVANT EMULSIFIABLE CONCENTRATE. A blend of surfactant with petroleum hydrocarbons for application with various herbicides
2016-01-21 2015-4853 MERGE ADJUVANT EMULSIFIABLE CONCENTRATE A blend of surfactant with petroleum hydrocarbons for application with various herbicides COMMERCIAL (AGRICULTURAL) GUARANTEE: Surfactant blend......