European history of the Company Company Profile. Bikroelast EPP 4.0

Transcription

1 content European history of the Company Company Profile 2 4 ROll-fed polymer-bitumen waterproofing materials SBS modified bitumen roofing and waterproofing membrane Bikroelast HPP BIPOL HPP Bikroelast HMP Bikroelast EPP Bikroelast EPP 4.0 UNIFLEKS EPP MIDA Standard PV S4 YAM 2000 BIPOL STANDART HKP BIPOL STANDART EKP BIPOL XL EKP UNIFLEKS EKP UNIFLEKS EKP APP modified bitumen roofing and waterproofing membrane ECOFLEKS V 2.0 ECOFLEKS PV 4.5 kg Mineral ECOFLEKS V 4.5 kg Mineral ECOFLEKS V 3.0 MIDA TROPIK P40M PRIMA PLAST NEW V 3.0 PRIMA PLAST GV 4.0 MIDA TROPIK C2000 PRIMA PLAST PV 4.5 kg Mineral SELF-ADHESIVE TAPES AND SEALANTS nicoband nicoband inside nicoband duo Table of technical specifications 34

2 2 About Company European history of the Company 1992 company was founded In 1993 in Moscow was opened the first office. In 1994 the Company launched its own first production plant for roll-fed roofing in Vyborg. In subsequent years, dozens of its own sales offices were opened throughout Russia The Vyborg plant started cooperating with Nordic countries, and it made its first deliveries of materials to Finland and Sweden. This established a new operational level for the Company, that set new challenges - acquiring knowledge of the foreign construction market, studying the regulatory and technological base became necessary The Company had 5 production sites and 35 retail branches in different regions of the Russian Federation. During this year the Company entered the Ukrainian market and opened its first retail branch in Kiev. Built in 1998 in Ryazan, the Technoflex plant became one of Europe s most modern factories in the production of roofing and waterproofing materials. In 1999 began deliveries to Eastern European countries (Slovakia and the Czech Republic, Poland) continued its expansion in Europe. The Company acquired its first foreign plant Gargzdu MIDA, located in Lithuania. At the same time, expanded its product range, and, therefore, MIDA factory, which was producing bitumen shingles, began producing of rollfed bitumen materials. This provided the Company opportunity to learn about a new and interesting segment - products for pitched roofs. Products started to be actively delivered to the Baltic countries (Latvia, Lithuania and Estonia) The product range was actively expanded, and new plants were launched: A production of stone wool heat insulation under the TECHNO brand was launched as the production of XPS, heat-insulating slabs made of extruded polystyrene foam. Plant for producing flexible tiles SHINGLAS was opened in Ryazan. Production of mastics was organized for making packaged deliveries of waterproofing and heat-insulating materials to European venues. Deliveries were made from Vyborg, Ryazan and Osipovichi plants. At the same time, representative offices in Latvia, Poland and Turkey were opened during this period.

3 about Company The Dehtochema Czech plant was acquired by the company, which is located in the city of Bělá pod Bezdězem. This plant had been manufacturing bitumen insulating materials for more than a hundred years. The plant was founded in The Company expanded its supply-chain to Central European countries. This time was difficult for the Company, since, like all other major European producers, became affected by the global economic crisis. But the Company successfully overcame the crisis, while maintaining and even strengthening its position in certain product markets The Company has cooperated with more than 50 independent sales partners and retailers operating in Western and Eastern Europe, Nordic countries, and Baltic countries. At the same time large-scale reconstruction of the plant in the Belarusian town of Osipovichi was on its way. An increase in the product range and capacity of the plant was aimed at the production of roll-fed materials focused exclusively on the European market. technonicol is the largest European manufacturer and supplier of roofing, waterproofing and heat-insulating materials. the Corporation includes 37 factories, its own retail network and representative offices in 36 countries. the corporation s turnover is more than 1350 million euros. the goal of technonicol is to create cost-effective materials and solutions for the protection of the environment and human health. more than 200 million people all over the world live and work in buildings constructed using technonicol materials. Iceland Norway Finland Sweden Estonia Denmark Latvia Lithuania Russia Great Britain Germany Poland Belarus Czech Republic Slovakia Ukraine Austria Hungary Moldavia Serbia Romania Bulgaria Macedonia Turkey Greece

4 4 About Company Company Profile The combination of advanced management, effective investments, and our structure aimed at company growth and development makes one of the leaders in production and distribution of insulation systems in Russia and European countries. Expanding our manufacturing capacities and our scope of services, implementing innovations, giving careful consideration to environment protection and energy efficiency, we are better than anybody else in meeting the social expectations and market demands. Own distribution network and representative offices in 36 countries of the world Our production is designed to meet your requirements: Our production capacities and equipment give us ability to supply materials for large construction projects and to develop unique products based on your individual requirements. Following the regional market demands, we extended geography of our plants. It made us more flexible and now we can supply our products more promptly without extra transportation costs. We are proud of what we produce and create. We enjoy seeing how new high-quality materials are produced from plain raw components with our up-to-date equipment, our work and efforts. We are glad to know that our materials are used in the construction of such complex objects as: houses, plants, bridges, and social infrastructure facilities, which improve the level and quality of life. Continuous progress and improvement: We are continuously improving ourselves and strive to do the same for the environment. Our goal is to set a new quality level for cooperation of all players in the construction market. We give consideration to both trivial and global issues: from usability of our products to upgrading the general qualification of specialists in the industry. recipe for success and continuous progress is first and foremost improvement of services for its clients and partners. Competence of our personnel, professional technical consultations, quality products and solutions, local bases and offices, entire scope of materials supply and installation services all these enable us to approach every client individually. We want to be leaders not just in quality product manufacturing but also in meeting our clients expectations. Social responsibility: We benefit society where we work and environment where we live. We enjoy being a part of what comes in 100 years. All plants of the Corporation are subjected to state environmental appraisal at their design stage. The inside and outside environment at our industrial sites is monitored daily. We invest in waste-free production, advanced equipment, and environmental protection technologies. All products developed and manufactured by meet sanitary and environmental standards and are safe for human beings and the environment. We create energy-efficient technologies and materials to save the environment. About 1 million euros/year is invested in environmental protection

5 BIKROELAST EPP 4.0 Multifunctional Universal waterproofing Durability SBS modified bitumen roofing and waterproofing Designed for installation as the bottom layer of roof cladding on buildings and constructions for waterproofing of engineering structures. Used for new roofing construction and for repair of old roof. Ideal for the installation as two-layer waterproofing for the foundations according to EN Can be used as underlayer for a bitumen shingles. Not recommended to use as one-layer roof cladding or one-layer waterproofing. SBS modified bitumen roofing and waterproofing membranes Bikroelast EPP 4.0 is roll-fed, torchable, SBS-modified bitumen roofing and waterproofing Material is produced by two-sided placing of modified bitumen binder, consisting from bitumen, SBS (styrene-butadiene-styrene) polymer modifier and mineral filler (talc, dolomite etc.), on the polyester carrier. Polymer film is used and bottom surfaces. Torch-on application on the prepared surface. At use as underlayer for a bitumen shingles fastened mechanically. Properties Test method SBS modified bitumen External fire performance EN ENV 1187:2002, test 2* В ROOF (t2)* Length / width, m EN Weight, kg/m 2 EN Reinforcement type and weight polyester, 180 g/m 2 Maximum tensile force longitudinal / transverse, N/50 mm EN /600±100 Resistance to tearing (nail shank), N EN /180±50 Elongation, % EN /50±25 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN /30 Watertightness, kpа EN * This material is part of a two-layer roofing system and corresponds to the B-roof only in combination with a second layer of roofing system.

6 BIKROELAST HPP SBS modified bitumen roofing and waterproofing Designed for installation as the bottom layer of roof cladding on buildings and constructions, for waterproofing of engineering structures and for vapour sealing. Used for new roofing construction and for repair of old roof on the rigid foundation. Not recommended to use as one-layer roof cladding or one-layer waterproofing. BIKROELAST HPP is roll-fed, torchable, SBS modified bitumen roofing and waterproofing Material is produced by two-sided placing of modified bitumen binder, consisting from bitumen, SBS (styrene-butadiene-styrene) polymer modifier and mineral filler (talc, dolomite etc.), on the glass-fiber mat carrier. Polymer film is used and bottom surfaces. SBS modified Underlay membrane Torch-on application on the prepared surface. * This material is part of a two-layer roofing system and corresponds to the B-roof only in combination with a second layer of roofing system. 6 Properties Test method BIKROELAST HPP External fire performance EN ENV 1187:2002, test 2* В ROOF (t2)* Length / width, m EN /16х1 Weight, kg/m 2 EN Reinforcement type and weight glass-fiber mat, 55 g/m 2 Maximum tensile force longitudinal / transverse, N/50 mm EN /250±100 Resistance to tearing (nail shank), N EN /50±10 Elongation, % EN /2.2±0.22 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN /30 Watertightness, kpа EN

7 BIPOL HPP SBS modified bitumen roofing and waterproofing Designed for installation as the bottom layer of roof cladding on buildings and constructions, for waterproofing of engineering structures and for vapour sealing. Used for new roofing construction and for repair of old roof on the rigid foundation. Not recommended to use as one-layer roof cladding or one-layer waterproofing. BIPOL HPP is roll-fed, torchable, SBS modified bitumen roofing and waterproofing Material is produced by two-sided placing of polymer-bitumen binder, consisting from bitumen, SBS (styrene-butadiene-styrene) polymer modifier and mineral filler (talc, dolomite etc.), on the glass-fiber mat carrier. Polymer film is used and bottom surfaces. Torch-on application on the prepared surface. SBS modified Underlay membrane Properties Test method BIPOL HPP External fire performance EN ENV 1187:2002, test 2* В ROOF (t2)* Length / width, m EN /16х1 Weight, kg/m 2 EN Reinforcement type and weight glass-fiber mat, 55 g/m 2 Maximum tensile force longitudinal / transverse, N/50 mm EN /250±100 Resistance to tearing (nail shank), N EN /50±10 Elongation, % EN /2.2±0.22 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN /30 Watertightness, kpа EN * This material is part of a two-layer roofing system and corresponds to the B-roof only in combination with a second layer of roofing system. 7

8 BIKROELAST HMP SBS modified bitumen roofing and waterproofing Designed for installation as the bottom layer of roof cladding on buildings and constructions, for waterproofing of engineering structures and for vapour sealing. Used for new roofing construction and for repair of old roof on the rigid foundation. Not recommended to use as one-layer roof cladding or one-layer waterproofing. BIKROELAST HMP is roll-fed, torchable, bitumen, SBS modified roofing waterproofing Material is produced by two-sided placing of modified bitumen binder, consisting from bitumen, SBS (styrene-butadiene-styrene) polymer modifier and mineral filler (talc, dolomite etc.), on the glass-fiber mat carrier. Polymer film is used surface. The protective finegrained sand layer is placed surface. It provides possibility to install of the next (top) layer of roof cladding by standard torch-on application or by attaching it on hot- or cold-applied mastics. SBS modified Underlay membrane Torch-on application on the prepared surface. * This material is part of a two-layer roofing system and corresponds to the B-roof only in combination with a second layer of roofing system. 8 Properties Test method BIKROELAST HMP External fire performance EN ENV 1187:2002, test 2* В ROOF (t2)* Length / width, m EN /16 1 Weight, kg/m 2 EN Reinforcement type and weight glass-fiber mat, 55 g/m 2 Maximum tensile force longitudinal / transverse, N/50 mm EN /250±100 Resistance to tearing (nail shank), N EN /50±10 Elongation, % EN /2.2±0.22 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN /30 Watertightness, kpа EN fine-grained sand

9 BIKROELAST EPP SBS modified bitumen roofing and waterproofing Designed for installation as the bottom layer of roof cladding on buildings and constructions for waterproofing of engineering structures. Used for new roofing construction and for repair of old roof. Ideal for the installation as two-layer waterproofing for the foundations (according to EN 13969). Not recommended to use as one-layer roof cladding or one-layer waterproofing. Bikroelast EPP is roll-fed, torchable, SBS modified bitumen roofing and waterproofing Material is produced by two-sided placing of modified bitumen binder, consisting from bitumen, SBS (styrene-butadiene-styrene) polymer modifier and mineral filler (talc, dolomite etc.), on the polyester carrier. Polymer film is used and bottom surfaces. SBS modified Torch-on application on the prepared surface. Underlay membrane Properties Test method BIKROELAST EPP External fire performance EN ENV 1187:2002, test 2* В ROOF (t2)* Length / width, m EN /16 1 Weight, kg/m 2 EN Reinforcement type and weight polyester, 150 g/m 2 Maximum tensile force longitudinal / transverse, N/50 mm EN /500±100 Resistance to tearing (nail shank), N EN /180±50 Elongation, % EN /50±25 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN /30 Watertightness, kpа EN * This material is part of a two-layer roofing system and corresponds to the B-roof only in combination with a second layer of roofing system. 9

10 BIKROELAST EPP 4.0 SBS modified bitumen roofing and waterproofing Designed for installation as the bottom layer of roof cladding on buildings and constructions for waterproofing of engineering structures. Used for new roofing construction and for repair of old roof. Ideal for the installation as two-layer waterproofing for the foundations (according to EN 13969). Not recommended to use as one-layer roof cladding or one-layer waterproofing. Bikroelast EPP 4.0 is roll-fed, torchable, SBS modified bitumen roofing and waterproofing Material is produced by two-sided placing of modified bitumen binder, consisting from bitumen, SBS (styrene-butadiene-styrene) polymer modifier and mineral filler (talc, dolomite etc.), on the polyester carrier. Polymer film is used and bottom surfaces. SBS modified Torch-on application on the prepared surface. Underlay membrane Properties Test method BIKROELAST EPP 4.0 External fire performance EN ENV 1187:2002, test 2* В ROOF (t2)* Length / width, m EN /10х1 Weight, kg/m 2 EN Reinforcement type and weight polyester, 150 g/m 2 Maximum tensile force longitudinal / transverse, N/50 mm EN /500±100 Resistance to tearing (nail shank), N EN /180±50 Elongation, % EN /50±25 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN /30 Watertightness, kpа EN * This material is part of a two-layer roofing system and corresponds to the B-roof only in combination with a second layer of roofing system. 10

11 UNIFLEKS EPP SBS modified bitumen roofing and waterproofing Designed for installation as the bottom layer of roof cladding on buildings and constructions for waterproofing of engineering structures. Used for new roofing construction and for repair of old roof. Ideal for the installation as two-layer waterproofing for the foundations (according to EN 13969). Not recommended to use as one-layer roof cladding or one-layer waterproofing. UNIFLEKS EPP is roll-fed, torchable, bitumen, roofing and waterproofing Material is produced by two-sided placing of polymer-bitumen binder, consisting from bitumen, SBS (styrene-butadiene-styrene) polymer modifier and mineral filler (talc, dolomite etc.), on the polyester carrier. Polymer film is used and bottom surfaces. SBS modified Torch-on application on the prepared surface. Underlay membrane Properties Test method UNIFLEKS EPP External fire performance EN ENV 1187:2002, test 2* В ROOF (t2)* Length / width, m EN /10х1 Weight, kg/m 2 EN Reinforcement type and weight polyester, 160 g/m 2 Maximum tensile force longitudinal / transverse, N/50 mm EN /500±100 Resistance to tearing (nail shank), N EN /180±30 Elongation, % EN /50±25 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN /30 Watertightness, kpа EN * This material is part of a two-layer roofing system and corresponds to the B-roof only in combination with a second layer of roofing system. 11

12 MIDA STANDARD PV S4 SBS modified bitumen roofing and waterproofing Designed for installation as the bottom layer of roof cladding on buildings and constructions. Used for new roofing construction and for repair of old roof. Not recommended to use as one-layer roof cladding. MIDA Standard PV S4 is roll-fed, torchable, bitumen, roofing waterproofing Material is produced by two-sided placing of polymer-bitumen binder, consisting from bitumen, SBS (styrene-butadiene-styrene) polymer modifier and mineral filler (talc, dolomite etc.), on the polyester carrier. Fine-grained sand or is used as the top protective layer. Polymer film is used surface. SBS modified Underlay membrane Torch-on application. Material can also be fastened mechanically, in this case membrane should be welded in the overlaps. * This material is part of a two-layer roofing system and corresponds to the B-roof only in combination with a second layer of roofing system. 12 Properties Test method MIDA STANDARD PV S4 External fire performance EN ENV 1187:2002, test 2* В ROOF (t2)* Length / width, m EN /10 1 Thickness, mm EN ±0.2 Reinforcement type polyester Maximum tensile force longitudinal / transverse, N/50 mm EN /500±100 Resistance to tearing (nail shank), N EN /200±100 Elongation, % EN /50±20 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN Watertightness, kpа EN 1928 watertight fine-grained sand or

13 YAM 2000 SBS modified bitumen roofing and waterproofing Designed for installation as the bottom layer of roof cladding, for waterproofing of engineering structures and for vapor sealing. Can be used as underlayer for bitumen shingles or other types of roofing materials for pitched roofs. Not recommended to use as one-layer roofing cladding or one-layer waterproofing. Material is produced by two-sided placing of polymer-bitumen binder, consisting from bitumen, SBS (styrene-butadiene-styrene) polymer modifier and mineral filler (talc, dolomite etc.), on the glass-fiber mat carrier. Fine-grained sand is used as the top and bottom protective surfaces. Glued to the prepared surface on cold- and hot-applied bitumen mastics. Fastened mechanically at use as underlayer. SBS modified Underlay membrane Properties Test method YAM 2000 External fire performance EN ENV 1187:2002, test 2* В ROOF (t2)* Length / width, m EN /20х1 Weight, kg/m 2 EN Reinforcement type and weight glass-fiber mat, 55 g/m 2 Maximum tensile force longitudinal / transverse, N/50 mm EN /300±50 Resistance to tearing (nail shank), N EN /30±10 Elongation, % EN /2.2±0.22 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN /30 Watertightness, kpа EN fine-grained sand fine-grained sand * This material is part of a two-layer roofing system and corresponds to the B-roof only in combination with a second layer of roofing system. 13

14 BIPOL STANDART HKP SBS modified bitumen roofing and waterproofing Designed for installation as the top layer of roof cladding on buildings and constructions, for waterproofing of engineering structures. Used for new roofing construction and for repair of old roof. Not recommended to use as one-layer roof cladding or one-layer waterproofing. BIPOL STANDART HKP is SBS modified bitumen roofing and waterproofing Material is produced by two-sided placing of modified bitumen binder, consisting from bitumen, SBS (styrene-butadiene-styrene) polymer modifier and mineral filler (talc, dolomite etc.), on the glass-fiber mat carrier. As top protective layer, the slate dressing compound is used for ultraviolet exposure protection of bitumen binder. Polymer film is used surface. SBS modified Torch-on application on the prepared surface. Cap sheet membrane * This material is part of a two-layer roofing system and corresponds to the B-roof only in combination with a second layer of roofing system. 14 Properties Test method BIPOL STANDART HKP External fire performance EN ENV 1187:2002, test 2* В ROOF (t2)* Length / width, m EN /10/12х1 Weight, kg/m 2 EN Reinforcement type and weight glass-fiber mat, 55 g/m 2 Maximum tensile force longitudinal / transverse, N/50 mm EN /250±100 Resistance to tearing (nail shank), N EN /50±10 Elongation, % EN /2.2±0.22 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN /30 Watertightness, kpа EN coarse-grained slate

15 BIPOL STANDART EKP SBS modified bitumen roofing and waterproofing Designed for installation as the top layer of roof cladding on buildings and constructions, for waterproofing of engineering structures. Used for new roofing construction and for repair of old roof. Not recommended to use as one-layer roof cladding or one-layer waterproofing. BIPOL STANDART EKP is SBS modified bitumen roofing and waterproofing Material is produced by two-sided placing of modified bitumen binder, consisting from bitumen, SBS (styrene-butadiene-styrene) polymer modifier and mineral filler (talc, dolomite etc.), on the polyester carrier. As top protective layer, the slate dressing compound is used for ultraviolet exposure protection of bitumen binder. Polymer film is used on the bottom surface. SBS modified Torch-on application on the prepared surface. Cap sheet membrane Properties Test method BIPOL STANDART EKP External fire performance EN ENV 1187:2002, test 2* В ROOF (t2)* Length / width, m EN /10 1 Weight, kg/m 2 EN Reinforcement type and weight polyester, 160 g/m 2 Maximum tensile force longitudinal / transverse, N/50 mm EN /500±100 Resistance to tearing (nail shank), N EN /180±50 Elongation, % EN /50±25 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN /30 Watertightness, kpа EN coarse-grained slate * This material is part of a two-layer roofing system and corresponds to the B-roof only in combination with a second layer of roofing system. 15

16 BIPOL XL EKP SBS modified bitumen roofing and waterproofing Designed for installation as the top layer of roof cladding on buildings and constructions, for waterproofing of engineering structures. Used for new roofing construction and for repair of old roof. Not recommended to use as one-layer roof cladding or one-layer waterproofing. BIPOL XL EKP is SBS modified bitumen roofing and waterproofing Material is produced by two-sided placing of polymer-bitumen binder, consisting from bitumen, SBS (styrene-butadiene-styrene) polymer modifier and mineral filler (talc, dolomite etc.), on the polyester carrier. As top protective layer, the slate dressing compound is used for ultraviolet exposure protection of bitumen binder. Polymer film is used on the bottom surface. SBS modified Torch-on application on the prepared surface. Cap sheet membrane Properties Test method BIPOL XL EKP External fire performance EN ENV 1187:2002, test 2* В ROOF (t2)* Length / width, m EN /10х1 Weight, kg/m 2 EN Reinforcement type and weight polyester, 160 g/m 2 Maximum tensile force longitudinal / transverse, N/50 mm EN /500±100 Resistance to tearing (nail shank), N EN /180±50 Elongation, % EN /50±25 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN /30 Watertightness, kpа EN coarse-grained slate * This material is part of a two-layer roofing system and corresponds to the B-roof only in combination with a second layer of roofing system. 16

17 UNIFLEKS EKP SBS modified bitumen roofing and waterproofing Designed for installation as the top layer of roof cladding on buildings and constructions, for waterproofing of engineering structures. Used for new roofing construction and for repair of old roof. Not recommended to use as one-layer roof cladding or one-layer waterproofing. UNIFLEKS EKP is roll-fed, torchable, bitumen, roofing and waterproofing Material is produced by two-sided placing of polymer-bitumen binder, consisting from bitumen, SBS (styrene-butadiene-styrene) polymer modifier and mineral filler (talc, dolomite etc.), on the polyester carrier. As top protective layer, the slate dressing compound is used for ultraviolet exposure protection of bitumen binder. Polymer film is used on the bottom surface. SBS modified Torch-on application on the prepared surface. Cap sheet membrane Properties Test method UNIFLEKS EKP External fire performance EN ENV 1187:2002, test 2* В ROOF (t2)* Length / width, m EN /10/12х1 Weight, kg/m 2 EN Reinforcement type and weight polyester, 160 g/m 2 Maximum tensile force longitudinal / transverse, N/50 mm EN /500±100 Resistance to tearing (nail shank), N EN /180±30 Elongation, % EN /50±25 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN /30 Watertightness, kpа EN coarse-grained slate * This material is part of a two-layer roofing system and corresponds to the B-roof only in combination with a second layer of roofing system. 17

18 UNIFLEKS EKP 5.0 SBS modified bitumen roofing and waterproofing Designed for installation as the top layer of roof cladding on buildings and constructions, for waterproofing of engineering structures. Used for new roofing construction and for repair of old roof. Not recommended to use as one-layer roof cladding or one-layer waterproofing. UNIFLEKS EKP 5.0 is roll-fed, torchable, bitumen, roofing and waterproofing Material is produced by two-sided placing of polymer-bitumen binder, consisting from bitumen, SBS (styrene-butadiene-styrene) polymer modifier and mineral filler (talc, dolomite etc.), on the polyester carrier. As top protective layer, the slate dressing compound is used for ultraviolet exposure protection of bitumen binder. Polymer film is used on the bottom surface. SBS modified Torch-on application on the prepared surface. Cap sheet membrane Properties Test method UNIFLEKS EKP 5.0 External fire performance EN ENV 1187:2002, test 2* В ROOF (t2)* Length / width, m EN /10/12х1 Weight, kg/m 2 EN Reinforcement type and weight polyester, 180 g/m 2 Maximum tensile force longitudinal / transverse, N/50 mm EN /600±100 Resistance to tearing (nail shank), N EN /180±30 Elongation, % EN /50±25 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN /30 Watertightness, kpа EN coarse-grained slate * This material is part of a two-layer roofing system and corresponds to the B-roof only in combination with a second layer of roofing system. 18

19 BIKROELAST EPP 4.0 Multifunctional Universal waterproofing Durability SBS modified bitumen roofing and waterproofing Designed for installation as the bottom layer of roof cladding on buildings and constructions for waterproofing of engineering structures. Used for new roofing construction and for repair of old roof. Ideal for the installation as two-layer waterproofing for the foundations according to EN Can be used as underlayer for a bitumen shingles. Not recommended to use as one-layer roof cladding or one-layer waterproofing. APP modified bitumen roofing and waterproofing membranes Bikroelast EPP 4.0 is roll-fed, torchable, SBS-modified bitumen roofing and waterproofing Material is produced by two-sided placing of modified bitumen binder, consisting from bitumen, SBS (styrene-butadiene-styrene) polymer modifier and mineral filler (talc, dolomite etc.), on the polyester carrier. Polymer film is used and bottom surfaces. Torch-on application on the prepared surface. At use as underlayer for a bitumen shingles fastened mechanically. Properties Test method APP modified bitumen External fire performance EN ENV 1187:2002, test 2* В ROOF (t2)* Length / width, m EN Weight, kg/m 2 EN Reinforcement type and weight polyester, 180 g/m 2 Maximum tensile force longitudinal / transverse, N/50 mm EN /600±100 Resistance to tearing (nail shank), N EN /180±50 Elongation, % EN /50±25 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN /30 Watertightness, kpа EN * This material is part of a two-layer roofing system and corresponds to the B-roof only in combination with a second layer of roofing system.

20 ECOFLEKS V 2.0 KG APP modified bitumen roofing and waterproofing Designed for installation as the bottom layer for various types of roofing systems. Can be used as vapor barrier and as a waterproofing cutoff. Material can also be used as underlayer for bitumen shingles or other types of roofing materials for pitched roofs. Not recommended to use as one-layer roof cladding or one-layer waterproofing. ECOFLEKS V 2.0 kg is APP modified bitumen roofing waterproofing Material is produced by two-sided placing of bitumen binder, consisting from bitumen, APP (atactic polypropylene) polymer modifier and mineral filler (talc, dolomite etc.), on the glass-fiber mat carrier. Polymer film is used and bottom surfaces. APP modified Underlay membrane Fastened mechanically at use as the bottom layer of roof cladding and as underlayer for bitumen shingles. At use as a vapor barrier or waterproofing cutoff is placed freely, welded in the overlaps. Properties Test method ECOFLEKS V 2.0 kg Fire reaction ЕN class Е Length / width, m EN /16х1 Weight, kg/m 2 EN ±0.2 Reinforcement type and weight glass-fiber mat, 55 g/m 2 Maximum tensile force longitudinal / transverse, N/50 mm EN /300±150 Resistance to tearing (nail shank), N EN /50±10 Elongation, % EN /4±2 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN /30 Watertightness, kpа EN

21 ECOFLEKS PV 4.5 kg Mineral APP modified bitumen roofing and waterproofing Designed for installation as the top layer of roof cladding on buildings and constructions, for waterproofing of engineering structures. Used for new roofing construction and for repair of old roof. Particularly suitable for local repair. Not recommended to use as one-layer roof cladding or one-layer waterproofing. ECOFLEKS PV 4.5 kg Mineral is APP modified bitumen roofing waterproofing Material is produced by two-sided placing of polymer-bitumen binder, consisting from bitumen, APP (atactic polypropylene) polymer modifier and mineral filler (talc, dolomite etc.), on the polyester carrier. As top protective layer, the slate dressing compound is used for ultraviolet exposure protection of bitumen binder. Polymer film is used surface. APP modified Torch-on application on the prepared surface. Cap sheet membrane Properties Test method ECOFLEKS PV 4.5 kg Mineral Fire reaction ЕN class Е Length / width, m EN /10/12х1 Weight, kg/m 2 EN ±0.2 Reinforcement type and weight polyester, 140 g/m 2 Maximum tensile force longitudinal / transverse, N/50 mm EN /450±150 Resistance to tearing (nail shank), N EN /180±50 Elongation, % EN /35±10 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN /30 Watertightness, kpа EN coarse-grained slate 21

22 ECOFLEKS V 4.5 kg Mineral APP modified bitumen roofing and waterproofing Designed for installation as the top layer of roof cladding on buildings and constructions, for waterproofing of engineering structures. Used for new roofing construction and for repair of old roof. Particularly suitable for local repair. Not recommended to use as one-layer roof cladding or one-layer waterproofing. ECOFLEKS V 4.5 kg Mineral is APP modified bitumen roofing waterproofing Material is produced by two-sided placing of polymer-bitumen binder, consisting from bitumen, APP (atactic polypropylene) polymer modifier and mineral filler (talc, dolomite etc.), on the glass-fiber mat carrier. As top protective layer, the slate dressing compound is used for ultraviolet exposure protection of bitumen binder. Polymer film is used surface. APP modified Torch-on application on the prepared surface. Cap sheet membrane Properties Test method ECOFLEKS V 4.5 kg Mineral Fire reaction ЕN class Е Length / width, m EN /10/12х1 Weight, kg/m 2 EN ±0.2 Reinforcement type and weight glass-fiber mat, 55 g/m 2 Maximum tensile force longitudinal / transverse, N/50 mm EN /300±150 Resistance to tearing (nail shank), N EN /50±10 Elongation, % EN /4±2 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN /30 Watertightness, kpа EN coarse-grained slate 22

23 ECOFLEKS V 3.0 kg APP modified bitumen roofing and waterproofing Designed for installation as the bottom layer of roof cladding on buildings and constructions. Used for new roofing construction and for repair of old roof. Not recommended to use as one-layer roof cladding or one-layer waterproofing. ECOFLEKS V 3.0 kg is APP modified bitumen roofing waterproofing Material is produced by two-sided placing of bitumen binder, consisting from bitumen, APP (atactic polypropylene) polymer modifier and mineral filler (talc, dolomite etc.), on the glass-fiber mat carrier. Polymer film is used and bottom surfaces. Torch-on application on the prepared surface. APP modified Underlay membrane Properties Test method ECOFLEKS V 3.0 kg Fire reaction ЕN class Е Length / width, m EN /16х1 Weight, kg/m 2 EN ±0.2 Reinforcement type and weight glass-fiber mat, 55 g/m 2 Maximum tensile force longitudinal / transverse, N/50 mm EN /300±150 Resistance to tearing (nail shank), N EN /50±10 Elongation, % EN /4±2 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN /30 Watertightness, kpа EN

24 MIDA TROPIK P40M APP modified bitumen roofing and waterproofing Designed for installation as the top layer of roof cladding on buildings and constructions. Used for new roofing construction and for repair of old roof. Not recommended to use as one-layer roof cladding. MIDA TROPIK P40M is roll-fed, torchable, bitumen, roofing and waterproofing Material is produced by two-sided placing of polymer-bitumen binder on polyester carrier. As top protective layer, the slate dressing compound is used for ultraviolet exposure protection of polymer-bitumen binder. Polymer film is used surface. Torch-on application on the prepared surface. APP modified Cap sheet membrane Properties Test method MIDA TROPIK P40M Fire reaction ЕN class Е Length / width, m EN Thickness, mm EN ±0.1 Reinforcement type polyester Maximum tensile force longitudinal / transverse, N/50 mm EN /400±100 Elongation, % EN /30±10 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С EN Watertightness, kpа EN 1928 absolute coarse-grained slate 24

25 PRIMA PLAST NEW V 3.0 APP modified bitumen roofing and waterproofing Designed for installation as the bottom layer for various types of roofing systems. Can be used as vapor sealing and as a waterproofing cutoff. Not recommended to use as one-layer roof cladding or one-layer waterproofing. Do not use on the base of mineral wool. PRIMA PLAST NEW V 3.0 is APP modified bitumen roofing waterproofing Material is produced by two-sided placing of bitumen binder, consisting from bitumen, APP (atactic polypropylene) polymer modifier and mineral filler (talc, dolomite etc.), on the glass-fiber mat carrier. Polymer film is used and bottom surfaces. APP modified Underlay membrane Torch-on application on the prepared surface. As the vapor barrier is placed freely on the plane, welded in the overlaps. Properties Test method PRIMA PLAST NEW V 3.0 Fire reaction ЕN class Е Length / width, m EN /16х1 Weight, kg/m 2 EN ±5% Reinforcement type glass-fiber mat Maximum tensile force longitudinal / transverse, N/50 mm EN /350 Elongation, % EN /5±2 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С EN Watertightness, kpа EN 1928 absolute 25

26 PRIMA PLAST GV 4.0 APP modified bitumen roofing and waterproofing Designed for installation as the bottom layer for various types of roofing systems. Can be used as vapor sealing and as a waterproofing cutoff. Not recommended to use as one-layer roofing cladding or one-layer waterproofing. PRIMA PLAST GV 4.0 is APP modified bitumen roofing waterproofing Material is produced by two-sided placing of bitumen binder, consisting from bitumen, APP (atactic polypropylene) polymer modifier and mineral filler (talc, dolomite etc.), on the glass-fiber mat carrier. Finegrained sand is used as the top protective layer. Polymer film is used on the bottom surface. APP modified Torch-on application on the prepared surface. As the vapor barrier is placed freely, welded in the overlaps. Underlay membrane Properties Test method PRIMA PLAST GV 4.0 Fire reaction ЕN class Е Length / width, m EN Weight, kg/m 2 EN ±5% Reinforcement type glass-fiber mat Maximum tensile force longitudinal / transverse, N/50 mm EN /300±150 Resistance to tearing (nail shank), N EN /50±10 Elongation, % EN /6±4 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN Watertightness, kpа EN 1928 absolute fine-grained sand 26

27 MIDA TROPIK C 2000 APP modified bitumen roofing and waterproofing Designed for installation as the bottom layer of roof cladding on buildings and constructions. Can be used as vapor sealing and as a waterproofing cutoff. Used for new roofing construction and for repair of old roof. Not recommended to use as one-layer roofing cladding. MIDA TROPIK C 2000 is roll-fed, torchable, bitumen, roofing and waterproofing Material is produced by two-sided placing of polymer-bitumen binder on glass-fiber mat carrier. The top and bottom surfaces of the material are covered with the. Torch-on application on the prepared surface. As the vapor barrier is placed freely, welded in the overlaps. APP modified Underlay membrane Properties Test method MIDA TROPIK C 2000 Fire reaction ЕN class Е Length / width, m EN Thickness, mm EN ±0.1 Reinforcement type glass-fiber mat Maximum tensile force longitudinal / transverse, N/50 mm EN /200±100 Resistance to tearing (nail shank), N EN /6±4 Elongation, % EN Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN Watertightness, kpа EN 1928 absolute 27

28 PRIMA PLAST PV 4.5 kg Mineral APP modified bitumen roofing and waterproofing Designed for installation as the top layer of roof cladding on buildings and constructions. Used for new roofing construction and for repair of old roof. Not recommended to use as one-layer roof cladding. PRIMA PLAST PV 4.5 kg Mineral is APP modified bitumen roofing waterproofing Manufactured according to ЕN 13707: А2:2009. Material is produced by two-sided placing of APP modified bitumen binder on the polyester carrier. As top protective layer, the slate dressing compound is used for ultraviolet exposure protection of bitumen binder. Polymer film is used surface. Torch-on application on the prepared surface. APP modified Cap sheet membrane Properties Test method PRIMA PLAST PV 4.5 kg Mineral Fire reaction ЕN class Е Length / width, m EN /10х1 Weight, kg/m 2 EN Reinforcement type polyester Maximum tensile force longitudinal / transverse, N/50 mm EN /400±150 Elongation, % EN /30±10 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С EN Adhesion of granules, % EN ±15 Watertightness, kpа EN 1928 absolute coarse-grained slate 28

29 BIKROELAST EPP 4.0 SBS modified bitumen roofing and waterproofing Designed for installation as the bottom layer of roof cladding on buildings and constructions for waterproofing of engineering structures. Used for new roofing construction and for repair of old roof. Ideal for the installation as two-layer waterproofing for the foundations according to EN Can be used as underlayer for a bitumen shingles. Not recommended to use as one-layer roof cladding or one-layer waterproofing. Multifunctional Universal waterproofing Durability Bikroelast EPP 4.0 is roll-fed, torchable, SBS-modified bitumen roofing and waterproofing Material is produced by two-sided placing of modified bitumen binder, consisting from bitumen, SBS (styrene-butadiene-styrene) polymer modifier and mineral filler (talc, dolomite etc.), on the polyester carrier. Polymer film is used and bottom surfaces. SELF-ADHESIVE TAPES AND SEALANTS Torch-on application on the prepared surface. At use as underlayer for a bitumen shingles fastened mechanically. Properties Test method SELF-ADHESIVE TAPES External fire performance EN ENV 1187:2002, test 2* В ROOF (t2)* Length / width, m EN Weight, kg/m 2 EN Reinforcement type and weight polyester, 180 g/m 2 Maximum tensile force longitudinal / transverse, N/50 mm EN /600±100 Resistance to tearing (nail shank), N EN /180±50 Elongation, % EN /50±25 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN /30 Watertightness, kpа EN * This material is part of a two-layer roofing system and corresponds to the B-roof only in combination with a second layer of roofing system.

30 SELF-ADHESIVE TAPES AND SEALANTS NICOBAND Colored aluminum coating with protection from UV radiation Self-adhesive sealing layer of bituminous Easily removable protective film Tape color Sealing and waterproofing. NICOBAND is a universal self-adhesive sealing tape. It is produced by placing a color reinforced aluminum covering on a waterproof self-adhesive bitumen layer. The protective film on the adhesive bitumen layer is easy to remove. The material is easy and convenient to use, and it bonds ideally to concrete, gypsum, metal, bitumen, stone, wood and other surfaces. The sealing tape is designed for sealing seams and joints, repairing cracks, waterproofing, and corrosion protection. The surface must be clean, dry, and free from rust and dust. For a better and more durable bond a priming of the base is recommended. The surface and material temperature must be at least +5 C. At lower temperatures it is necessary to heat the adhesive side of the material and the base. It is not recommended to apply a tape to hot vertical surfaces (with a temperature above +85 C). Storage: Store in a place protected from atmospheric precipitation and direct sunlight. Basic dimensions Width, cm Length 3 m Length 10 m

31 SELF-ADHESIVE TAPES AND SEALANTS NICOBAND INSIDE Non-woven polypropylene (Spunbond) Bituminous self-adhesive sealing layer Easily removable protective film The material is intended for indoor use. Suitable for: Sealing joints in the ventilation system (ducts, floors exible ducts). Sealing of various pipes in cold areas. The product adjacencies to the walls, and other protruding parts for sealing the interior floors of the roll and mastic materials. The unit is waterproof floors in the rooms (bathrooms, kitchen) without the use of protective cement sand screed. Directly on the material can be glued ceramic tile. Also used where the material will be closed from the effects of UV-rays: The unit capillary cutoff for masonry and wood construction. Vapor barrier and waterproofing assembly seams at the organization of heat insulation of foamed polyethylene. NICOBAND INSIDE is a self-adhesive sealing and waterproofing polymer-bitumen tape. Produced by unilateral application of anti-adhesion to the self-adhesive bitumen-polymer binder consisting of bitumen, SIS (styrene-isoprene-styrene) polymer modifiers and special adhesive additives. Self-adhesive non-woven polypropylene (Spunbond) is used as a protective layer on the other side. Attached to the dry and cleaned surface. Fit, without any equipment. It is recommended to work at temperatures above +5 C. Storage: Store in a place protected from atmospheric precipitation and direct sunlight. Basic dimensions Width, cm Length 3 m Length 10 m

32 SELF-ADHESIVE TAPES AND SEALANTS NICOBAND DUO Easily removable protective film Bituminous self-adhesive sealing layer Easily removable protective film Sealing seams, cracks and joints. Description of material: NICOBAND DUO is a double-sided self-adhesive polymer-bitumen tape for sealing hidden seams and joints, for temporary fastening or for the simultaneous fixation and sealing of small elements. NICOBAND DUO consists of a polymer-bitumen layer of a special composition that provides good adhesion to virtually any surface. On both sides it is protected by s, which are easily removed. The material is easy and convenient to apply. Has excellent adhesion to metal, concrete, plastic, asphalt, wood, glass, etc. The surface must be clean, dry, and free from rust and dust. For a better and more durable bond a priming of the base is recommended. The surface and material temperature must be at least +5 C. At lower temperatures it is necessary to heat the adhesive side of the material and the base. It is not recommended to apply a tape to hot vertical surfaces (with a temperature above +85 C). Storage: Store in a place protected from atmospheric precipitation and direct sunlight. Basic dimensions Width, cm Length 3 m Length 10 m

33 BIKROELAST EPP 4.0 SBS modified bitumen roofing and waterproofing Designed for installation as the bottom layer of roof cladding on buildings and constructions for waterproofing of engineering structures. Used for new roofing construction and for repair of old roof. Ideal for the installation as two-layer waterproofing for the foundations according to EN Can be used as underlayer for a bitumen shingles. Not recommended to use as one-layer roof cladding or one-layer waterproofing. Multifunctional Universal waterproofing Durability Bikroelast EPP 4.0 is roll-fed, torchable, SBS-modified bitumen roofing and waterproofing Material is produced by two-sided placing of modified bitumen binder, consisting from bitumen, SBS (styrene-butadiene-styrene) polymer modifier and mineral filler (talc, dolomite etc.), on the polyester carrier. Polymer film is used and bottom surfaces. Table of technical specifications Torch-on application on the prepared surface. At use as underlayer for a bitumen shingles fastened mechanically. Properties Test method Table of technical specifications External fire performance EN ENV 1187:2002, test 2* В ROOF (t2)* Length / width, m EN Weight, kg/m 2 EN Reinforcement type and weight polyester, 180 g/m 2 Maximum tensile force longitudinal / transverse, N/50 mm EN /600±100 Resistance to tearing (nail shank), N EN /180±50 Elongation, % EN /50±25 Flow resistance at elevated temperature, С EN Flexibility at low temperature, С / Ø mm EN /30 Watertightness, kpа EN * This material is part of a two-layer roofing system and corresponds to the B-roof only in combination with a second layer of roofing system.