Owner's Manual & Installation Instructions - Lift and Slide Systems

Transcription

1 Owner's Manual & Installation Instructions - Lift and Slide Systems Sheet Title Table Of ontents over Sheet...Page 1 Systems Technical Information & Data...Page 2 System Testing and Information...Page 3 Panel onstruction, Parts Verification, Tools...Page 4 Lift and Slide Panel Selection / Types... Page 5 Rough Opening Dimension Verification... Page 6 Bottom Track Installation... Page 7 Installation of Header & Side Frames... Page 8 Installation of System Panels... Page 9 System with Pocket Installation...Page 10 Final Finishing Of System... Page 11 System Maintenance... Page 12 *The system shown above is a TS19, Which is a thermally broken system. It is shown above with a full header track and side frames, but is typically built with a staggered header, side frames and bottom track. Please reassure your installation area and assure that you have ordered the correct configuration prior to installation. This Owner's Manual contains directions on the installation, operation and maintenance of your Panda Window's & Door's Lift And Slide System(s), TS19, S85,S10,IS14,S11,TS87,TS13,S12,S15. This set of instructions is to be used by the installer(s) during the installation process and needs to be kept by the system(s) Owner for reference and normal maintenance. If replacement parts need to be ordered, the owner can you this manual and contact Panda Window's & Door's Directly for the parts needed. You can refer to Parts List included with this manual to insure a correct and easier ordering process. Questions & oncerns; Visit our web site or ontact the your sales representative for assistance. over Sheet 1 OF 12

2 System Overview: reated to be the definitive solution for homes and structures in extreme weather conditions, the Thermally Broken Lift and Slide model brings industry-leading efficiency and unmatched functionality to any building. Number of Panels: ountless panel groups can be built. Profiles: Profiles are manufactured from 6063-T5 extruded aluminum with a wall thickness of up to 1/8 allowing for oversized panels. Polyamide iso-bars provide greater structural integrity and sheer strength over other thermal break options. System onfigurations Available: Almost any size and shape of opening can be accommodated. Systems can pocket to left or right, and can stack to left and/or right. 45 and 90 degree configurations are available. Smaller sized panels to be used in window or pass-through configurations are also available. Glazing: lear Low-E Insulated is the standard. Various types of glass and other materials at a thickness of up to 1 7/8 may be used. Optional integrated blinds are available. Weather-stripping: The entire door system has specially designed EPDM V-type gaskets and dense felt brushes to create a totally closed weather sealed system. ADA ompliant Standard Track. Recessed into sub-floor to ensure the smoothest possible operation. The finished floor is laid in between tracks leaving only a 3/16 rail exposed. A virtually unobstructed threshold from the interior to the exterior area for a barefoot friendly passage. ADA ompliant Track with drainage. In addition to the above features, this track has a weep channel for increased security against water infiltration. Panda holds a patent for the drainage technology used in this track. ADA ompliant 1 1/4 in track. Recessed into sub-floor to ensure the smoothest possible operation, this track features a shallower recess than the two tracks mentioned above and is leveled with stack shims instead of all-threads. The finished floor is laid in between tracks leaving only a 3/16 rail exposed. A virtually unobstructed threshold from the interior to the exterior area for a barefoot friendly passage. ADA ompliant 1 1/4 in track with drainage. In addition to the features mentioned for the previous track, this one has a weep channel for increased security against water infiltration. Panda holds a patent for the drainage technology used in this track. ADA ompliant Surface Track. It is used in situations where recessing is not possible. This low 3/16 track mounts directly to the finished floor. For best operation, floor must be smooth and level. Surface Drainage Track. This track sits on the floor with a sill pan featuring drain ports on the bottom of the track. Water travels to the exterior with the help of the sill pan. The header track features adjustable shims from 1/2 depending on type of bottom track and type of sill finish. The header track widths approximately 2 1/2 per track. Trench width and type of bottom track should be taken into account when planning rough header construction. Lift and Slides Technical Data Per System: System Technical Data Information 2 OF 12 System Overview: This Lift Slide patio door offers incredible comfort and energy efficiency to any home or building, but this model s added wood insulation guarantees structure interiors are warmer in the winter and cooler in the summer, and its isolated aluminum frame makes it strong and resistant to the harshest elements while drastically reducing the need for finish maintenance. Number of Panels: ountless panel groups can be built. Profiles: Manufactured from 6063-T5 extruded aluminum with a profile thickness of 1/8 allowing for oversized panels. The interior wood is uniquely cladded to the profiles by durable polyamide clips which create a thermal barrier for better UV and SFG performance. System onfigurations Available: Almost any size and shape of opening can be accommodated. Systems can pocket to left or right, and can stack to left and/or right. 45 and 90 degree configurations are available. Smaller sized panels to be used in window or pass-through configurations are also available. Glazing: lear Low-E Insulated is the standard. Various types of glass and other materials at a thickness of up to 1 7/8 may be used. Optional integrated blinds are available. Weather-stripping: The entire door system has specially designed EPDM V-type gaskets and dense felt brushes to create a totally closed weather sealed system. ADA ompliant Standard Track. Recessed into sub-floor to ensure the smoothest possible operation. The finished floor is laid in between tracks leaving only a 3/16 rail exposed. A virtually unobstructed threshold from the interior to the exterior area for a barefoot friendly passage. ADA ompliant Track with drainage. In addition to the above features, this track has a weep channel for increased security against water infiltration. Panda holds a patent for the drainage technology used in this track. ADA ompliant 1 1/4 in track. Recessed into sub-floor to ensure the smoothest possible operation, this track features a shallower recess than the two tracks mentioned above and is leveled with stack shims instead of all-threads. The finished floor is laid in between tracks leaving only a 3/16 rail exposed. A virtually unobstructed threshold from the interior to the exterior area for a barefoot friendly passage. ADA ompliant 1 1/4 in track with drainage. In addition to the features mentioned for the previous track, this one has a weep channel for increased security against water infiltration. Panda holds a patent for the drainage technology used in this track. ADA ompliant Surface Track. It is used in situations where recessing is not possible. This low 3/16 track mounts directly to the finished floor. For best operation, floor must be smooth and level. Surface Drainage Track. This track sits on the floor with a sill pan featuring drain ports on the bottom of the track. Water travels to the exterior with the help of the sill pan. The header track features adjustable shims from 1/2 to 1 depending on type of bottom track and finished floor thickness. The header track widths are 4 for one panel, 7 for two panels, 10 for three panels, and 13 for four panels approximately. Trench width should be taken into account when planning rough header construction. Lift and Slides Technical Data Per System: TS19 Thermal System: TS13 Thermal System: System Overview: With thermally broken extrusions and the slimmest line of all our offerings, the TS.87 is perfect for contemporary architecture and chic designs for the most modern of homes and properties. The stile width is 40% smaller than the typical Lift and Slide door, thus making this the premier option for sleek architectural designs where a contemporary appeal is desired. This model features an extra-low U-value, adding greater performance and weather protection to its genuine elegance. Number of Panels: ountless panel groups can be built. Profiles: Specially designed profiles are used in this system to provide maximum durability while providing a subtle visual divide. The Lift and Slide door profiles are made using high tensile 6063-T5 aluminum extrusions for superior strength. The stile sizes are as follows: Slim/narrow 3 1/4 by 2 aluminum stile. System onfigurations Available: Almost any size and shape of opening can be accommodated. Systems can pocket to left or right, and can stack to left and/or right. 45 and 90 degree configurations are available. Smaller sized panels to be used in window or pass-through configurations are also available. Glazing: lear Low-E tempered 1 3/8" insulated is the standard. A minimum of 1/4" single pane glass to a maximum of 1 1/2 hurricane rated insulated glass may be used. Optional integrated blinds are available for 1 1/2 insulated glass. Other options including frosted or tinted glass, argon or krypton fill, and SDLs or TDLs may also be integrated for a more custom look. Weather-stripping: The entire door system has specially designed EPDM V-type gaskets and dense felt brushes to create a totally closed weather sealed system. ADA ompliant Standard Track. Recessed into sub-floor to ensure the smoothest possible operation. The finished floor is laid in between tracks leaving only a 3/16 rail exposed. A virtually unobstructed threshold from the interior to the exterior area for a barefoot friendly passage. ADA ompliant Track with drainage. In addition to the above features, this track has a weep channel for increased security against water infiltration. Panda holds a patent for the drainage technology used in this track. ADA ompliant 1 1/4 in track. Recessed into sub-floor to ensure the smoothest possible operation, this track features a shallower recess than the two tracks mentioned above and is leveled with stack shims instead of all-threads. The finished floor is laid in between tracks leaving only a 3/16 rail exposed. A virtually unobstructed threshold from the interior to the exterior area for a barefoot friendly passage. ADA ompliant 1 1/4 in track with drainage. In addition to the features mentioned for the previous track, this one has a weep channel for increased security against water infiltration. Panda holds a patent for the drainage technology used in this track. ADA ompliant Surface Track. It is used in situations where recessing is not possible. This low 3/16 track mounts directly to the finished floor. For best operation, floor must be smooth and level. Surface Drainage Track. This track sits on the floor with a sill pan featuring drain ports on the bottom of the track. Water travels to the exterior with the help of the sill pan. The header track features adjustable shims from 1/2 depending on type of bottom track and type of sill finish. The header track widths approximately 2 1/2 per track. Trench width and type of bottom track should be taken into account when planning rough header construction. TS87 Thermal System: System Overview: Designed to comply with stringent Florida Building odes TAS 201; TAS 202; and TAS 203; and U.S. building regulations from wind-borne debris areas outside the high velocity hurricane zone (HVHZ), the IS.14 features superior components that can endure large missile and hurricane impact. This system permits oversized panels to withstand ategory 5 Hurricanes, tropical storms, high winds and driving rain, while standing up to coastal pressures such as corrosion, humidity and salt. Testing simulations made on the (IS.14) Impact Lift and Slide system by a third party company resulted in outstanding results with structural loads at 100 psf, water infiltration at 20 psf, and air infiltration at 1.57 psf for a large 5 x 10 system and even larger 5 x 12 model. With these results, Panda becomes the only manufacturer in the industry with the ability to craft large-sized panels while providing ultimate performance and weather protection. Maximum Panel Width: Up to 5 feet. Number of Panels: ountless panel groups can be built. Profiles: Manufactured from 6063-T5 extruded aluminum with a profile thickness of 2 3/4 allowing for oversized panels. Rail & Stiles: Narrow 4 1/2 stile and rail profiles for maximum view and minimal obstruction. System onfigurations Available: Systems can pocket to left or right, and can stack to left and/or right. Straight, 45 and 90 zero-post corner configurations are available. Glazing: Laminated impact resistant glass, either ½ monolithic or 1 3/8 double insulating glass. Optional integrated blinds are available. Weather-stripping: The entire door system has specially designed EPDM V-type gaskets and dense felt brushes to create a totally closed weather sealed system. ADA ompliant Standard Track. Recessed into sub-floor to ensure the smoothest possible operation. The finished floor is laid in between tracks leaving only a 3/16 rail exposed. A virtually unobstructed threshold from the interior to the exterior area for a barefoot friendly passage. ADA ompliant Track with drainage. In addition to the above features, this track has a weep channel for increased security against water infiltration. Panda holds a patent for the drainage technology used in this track. ADA ompliant 1 1/4 in track. Recessed into sub-floor to ensure the smoothest possible operation, this track features a shallower recess than the two tracks mentioned above and is leveled with stack shims instead of all-threads. The finished floor is laid in between tracks leaving only a 3/16 rail exposed. A virtually unobstructed threshold from the interior to the exterior area for a barefoot friendly passage. ADA ompliant 1 1/4 in track with drainage. In addition to the features mentioned for the previous track, this one has a weep channel for increased security against water infiltration. Panda holds a patent for the drainage technology used in this track. ADA ompliant Surface Track. It is used in situations where recessing is not possible. This low 3/16 track mounts directly to the finished floor. For best operation, floor must be smooth and level. Surface Drainage Track. This track sits on the floor with a sill pan featuring drain ports on the bottom of the track. Water travels to the exterior with the help of the sill pan. The header track features adjustable shims from 1/2 to 1 depending on type of bottom track and finished floor thickness. The header track widths are 4 for one panel, 7 for two panels, 10 for three panels, and 13 for four panels approximately. Trench width should be taken into account when planning rough header construction. IS14 Impact System: System Overview: This aluminum Lift Slide door system has been specifically engineered for maximum weather tightness, security and performance. Number of Panels: ountless panel groups can be built. Profiles: Manufactured from 6063-T5 extruded aluminum with a profile thickness of 2 3/4 allowing for oversized panels. System onfigurations Available: Almost any size and shape of opening can be accommodated. This aluminum Lift Slide door system can pocket to left or right, and can stack to left and/or right. 45 and 90 degree no-post configurations are available, as well as panoramic with a radius of minimum 144. Glazing: lear Low-E insulated is the standard. Various types of glass and other materials at a thickness of up to 1 7/8 may be used. Optional integrated blinds are available. Weather-stripping: The entire Lift and Slide door system has specially designed EPDM V-type gaskets and dense felt brushes to create a totally closed weather sealed system. Standard Recessed Track. Recessed into sub-floor to ensure the smoothest possible operation. The finished floor is laid in between tracks leaving only a 3/16 rail exposed. A virtually unobstructed threshold from the interior to the exterior area for a barefoot friendly passage. ADA compliant. Standard Recessed Drainage Track. In addition to the above features, this track has a weep channel for increased security against water infiltration. Panda holds a patent for the drainage technology used in this track. ADA compliant. Recessed Track. Recessed into sub-floor to ensure the smoothest possible operation, this track features a shallower recess than the two tracks mentioned above and is leveled with stack shims instead of all-threads. The finished floor is laid in between tracks leaving only a 3/16 rail exposed. A virtually unobstructed threshold from the interior to the exterior area for a barefoot friendly passage. ADA compliant. Recessed Drainage Track. In addition to the features mentioned for the previous track, this one has a weep channel for increased security against water infiltration. Panda holds a patent for the drainage technology used in this track. ADA compliant. Mounts on floor 5/16 Surface Track. It is used in situations where recessing is not possible. This low 5/16 track mounts directly to the finished floor. For best operation, floor must be smooth and level. Surface Drainage Track. This track sits on the floor with a sill pan featuring drain ports on the bottom of the track. Water travels to the exterior with the help of the sill pan. The header track features adjustable shims from 1/2 to 1 depending on type of bottom track and finished floor thickness. The header track widths are 4 for one panel, 7 for two panels, 10 for three panels, and 13 for four panels approximately. Trench width should be taken into account when planning rough header construction. If you are looking for an aluminum Lift Slide for applications in extreme climate conditions, please consider the TS.19 Thermally Broken Lift and Slide which provides superior thermal performance and energy efficiency. S10 Aluminum System: System Overview: This system has been specifically engineered for maximum weather tightness, security and performance. Number of Panels: ountless panel groups can be built. Profiles: Manufactured from 6063-T5 extruded aluminum with a profile thickness of 1/8 allowing for oversized panels. The interior wood is uniquely cladded to the profiles by durable polyamide clips which create a thermal barrier for better UV and SFG performance. System onfigurations Available: Almost any size and shape of opening can be accommodated. Systems can pocket to left or right, and can stack to left and/or right. 45 and 90 degree configurations are available, as well as panoramic with a radius of minimum 144. Glazing: lear Low-E insulated is the standard. Various types of glass and other materials at a thickness of up to 1 7/8 may be used. Optional integrated blinds are available. Weather-stripping: The entire door system has specially designed EPDM V-type gaskets and dense felt brushes to create a totally closed weather sealed system. ADA ompliant Standard Track. Recessed into sub-floor to ensure the smoothest possible operation. The finished floor is laid in between tracks leaving only a 3/16 rail exposed. A virtually unobstructed threshold from the interior to the exterior area for a barefoot friendly passage. ADA ompliant Track with drainage. In addition to the above features, this track has a weep channel for increased security against water infiltration. Panda holds a patent for the drainage technology used in this track. ADA ompliant 1 1/4 in track. Recessed into sub-floor to ensure the smoothest possible operation, this track features a shallower recess than the two tracks mentioned above and is leveled with stack shims instead of all-threads. The finished floor is laid in between tracks leaving only a 3/16 rail exposed. A virtually unobstructed threshold from the interior to the exterior area for a barefoot friendly passage. ADA ompliant 1 1/4 in track with drainage. In addition to the features mentioned for the previous track, this one has a weep channel for increased security against water infiltration. Panda holds a patent for the drainage technology used in this track. ADA ompliant Surface Track. It is used in situations where recessing is not possible. This low 3/16 track mounts directly to the finished floor. For best operation, floor must be smooth and level. Surface Drainage Track. This track sits on the floor with a sill pan featuring drain ports on the bottom of the track. Water travels to the exterior with the help of the sill pan. The header track features adjustable shims from 1/2 to 1 depending on type of bottom track and finished floor thickness. The header track widths are 4 for one panel, 7 for two panels, 10 for three panels, and 13 for four panels approximately. Trench width should be taken into account when planning rough header construction. S11 Aluminum System: System Overview: Designed for the luxury market, Panda s wood Lift Slide door system is a beautiful complement to any design that utilizes the warmth and elegance of wood. Maximum Panel Height: Up to 12 feet. Panel Weight: Approximately 8 to 9 lbs/sqft depending on overall panel size. Number of Panels: ountless panel groups can be built. Profiles: Manufactured of an engineered solid hard wood core and wrapped with a 1/4 wood veneer. The solid hard wood core increases the door strength and longevity over other wood door systems. There are integrated aluminum extrusions in the wheel carriage and glazing cavities for more stability and strength. System onfigurations Available: Almost any size and shape of opening can be accommodated. Systems can pocket to left or right, and can stack to left and/or right. 45 and 90 degree configurations are available, as well as panoramic with a radius of minimum 144. Smaller sized panels to be used in window or pass-through configurations are also available. Glazing: lear Low-E insulated is the standard. Various types of glass and other materials at a thickness of up to 1 may be used. Optional integrated blinds are available. Weather-stripping: The entire door system has specially designed EPDM V-type gaskets and dense felt brushes to create a totally closed weather sealed system. ADA ompliant Standard Track. Recessed into sub-floor to ensure the smoothest possible operation. The finished floor is laid in between tracks leaving only a 3/16 rail exposed. A virtually unobstructed threshold from the interior to the exterior area for a barefoot friendly passage. ADA ompliant Track with drainage. In addition to the above features, this track has a weep channel for increased security against water infiltration. Panda holds a patent for the drainage technology used in this track. ADA ompliant 1 1/4 in track. Recessed into sub-floor to ensure the smoothest possible operation, this track features a shallower recess than the two tracks mentioned above and is leveled with stack shims instead of all-threads. The finished floor is laid in between tracks leaving only a 3/16 rail exposed. A virtually unobstructed threshold from the interior to the exterior area for a barefoot friendly passage. ADA ompliant 1 1/4 in track with drainage. In addition to the features mentioned for the previous track, this one has a weep channel for increased security against water infiltration. Panda holds a patent for the drainage technology used in this track. ADA ompliant Surface Track. It is used in situations where recessing is not possible. This low 3/16 track mounts directly to the finished floor. For best operation, floor must be smooth and level. The header track features adjustable shims from 1/2 to 1 depending on type of bottom track and finished floor thickness. The header track widths are 4 for one panel, 7 for two panels, 10 for three panels, and 13 for four panels approximately. Trench width should be taken into account when planning rough header construction. S12 Aluminum System: System Overview: This system has been specifically engineered for maximum weather tightness, security and performance. Maximum Panel Height: Up to 10 feet or up to 12 feet with a true divider. Panel Weight: Approximately 8 to 9 lbs/sqft depending on overall panel size. Number of Panels: ountless panel groups can be built. Profiles: Manufactured from 6063-T5 extruded aluminum core, and 5/8 solid wood interior and exterior framing for a profile thickness of 3. The wood is uniquely cladded to the profiles by durable polyamide clips which create a thermal barrier for better UV and SFG performance. System onfigurations Available: Almost any size and shape of opening can be accommodated. Systems can pocket to left or right, and can stack to left and/or right. 90-degree configurations are available, as well as panoramic with a radius of minimum 144. Glazing: lear Low-E tempered-insulated 1 glass is the standard. Various types of glass and other materials at a thickness of up to 1 may be used. Optional automated blinds, SDLs and TDLs are available. Weather-stripping: The entire door system has specially designed EPDM V-type gaskets and dense felt brushes to create a totally closed weather sealed system. Trench Depth: Min. 2 1/4 Standard Recessed Track. Recessed into sub-floor to ensure the smoothest possible operation. The finished floor is laid in between tracks leaving only a 3/16 rail exposed. A virtually unobstructed threshold from the interior to the exterior area for a barefoot friendly and ADA compliant passage. Standard Recessed Track with drainage. In addition to the above features, this track has a weep channel for increased security against water infiltration. Panda holds a patent for the drainage technology used in this track. Trench Depth: Min. 1 1/2 1 1/4 Recessed track. Recessed into sub-floor to ensure the smoothest possible operation, this track features a shallower recess than the two tracks mentioned above and is leveled with stack shims instead of all-threads. The finished floor is laid in between tracks leaving only a 3/16 rail exposed. A virtually unobstructed threshold from the interior to the exterior area for a barefoot friendly and ADA compliant passage. 1 1/4 Recessed track with drainage. In addition to the features mentioned for the previous track, this one has a weep channel for increased security against water infiltration. Panda holds a patent for the drainage technology used in this track. ADA ompliant Surface Track. It is used in configurations where recessing is not possible. This low 5/16 track mounts directly to the finished floor. For best operation, floor must be smooth and level. Top Track: The header track features adjustable shims from 1/2 to 1 depending on type of bottom track and finished floor thickness. The header track widths are 4 for one panel, 8 for two panels, 12 for three panels, and 16 for four panels approximately. Trench width should be taken into account when planning rough header construction. S15 Aluminum System: System Overview: With the slimmest profile on the market among Lift and Slide products, this system provides a superior view by maximizing the glass to frame ratio. The stile width is 40% smaller than the typical door, thus making this the premier option for sleek architectural designs where a contemporary appeal is desired. Number of Panels: ountless panel groups can be built. Profiles: Specially designed profiles are used in this system to provide maximum durability while providing a subtle visual divide. The profiles are made using high tensile 6063-T5 aluminum extrusions for superior strength. The stile sizes are as follows: the interlocking stile is 2 3/4 wide and 2 thick, the locking stile is 2 3/4 wide and 2 thick, and the bottom rail is 3 3/4 wide and 2 thick. System onfigurations Available: Almost any size and shape of opening can be accommodated. Systems can pocket to left or right, and can stack to left and/or right. 45 and 90 degree configurations are available, as well as panoramic with a radius of minimum 144. Smaller sized panels to be used in window or pass-through configurations are also available. Glazing: lear Low-E tempered 1 3/8 insulated is the standard. A minimum of 1/4 single pane glass to a maximum 1 1/2 hurricane rated insulated glass may be used. Optional integrated blinds are available for 1 1/2 insulated glass. Other options including frosted or tinted glass, argon or krypton fill, and SDLs or TDLs may also be integrated for a more custom look. Weather-stripping: The entire door system has specially designed EPDM V-type gaskets and dense felt brushes to create a totally closed weather sealed system. ADA ompliant Standard Track. Recessed into sub-floor to ensure the smoothest possible operation. The finished floor is laid in between tracks leaving only a 3/16 rail exposed. A virtually unobstructed threshold from the interior to the exterior area for a barefoot friendly passage. ADA ompliant Track with drainage. In addition to the above features, this track has a weep channel for increased security against water infiltration. Panda holds a patent for the drainage technology used in this track. ADA ompliant 1 1/4 in track. Recessed into sub-floor to ensure the smoothest possible operation, this track features a shallower recess than the two tracks mentioned above and is leveled with stack shims instead of all-threads. The finished floor is laid in between tracks leaving only a 3/16 rail exposed. A virtually unobstructed threshold from the interior to the exterior area for a barefoot friendly passage. ADA ompliant 1 1/4 in track with drainage. In addition to the features mentioned for the previous track, this one has a weep channel for increased security against water infiltration. Panda holds a patent for the drainage technology used in this track. ADA ompliant Surface Track. It is used in situations where recessing is not possible. This low 3/16 track mounts directly to the finished floor. For best operation, floor must be smooth and level. The header track features adjustable shims from 1/2 depending on type of bottom track and type of sill finish. The header track widths approximately 2 1/2 per track. Trench width and type of bottom track should be taken into account when planning rough header construction. S85 Aluminum System:

3 Lift and Slides Technical Data Per System: Lift and Slides onfiguration and olor Options PANDA SYSTEM TESTING AND INFORMATION 3 OF 12

4 Parts Verification & Replacement Lift and Slide Typical Panel Parts: Lift and Slide Panel Section/Parts: Interlocks: Part Description: Part #: Part Name: HSW-01 Glazing Gasket HSW-06 HSW-05 HSW-06 HSW-02 Glazing Gasket HSW-03 Glazing Gasket HSW-04 Lower Weather Gasket HSW-05 Upper Weather Gasket HSW-02 HSW-06 Interlock lip HSW-01 HSW-07 HSW-08 HSW-09 (Fixed Panels Only) This part is used in lieu of the wheel mechanism. (Attached with screws) (Handle Mechansim) This part was design specifically for the lift & slide wheel hardware. (Handle Mechansim) This part was design specifically for the lift & slide wheel hardware. HSW-08 HSW-02 HSW-01 HSW-10 (Plastic Dog Ear lip) lip is used to hold the wood to the aluminum. (Wood Systems Only) HSW-07 HSW-09 HSW-04 HSW-06 Notifications Symbols: Basic Tools Required For Installation: Please read these instructions in their entirety before starting install Tips/Hints Seek Assistance Warning During the reading process of these installation instruction, you will see this information symbol. This is will you will find helpful tips and infomation you will need to know. This symbol indicates that we recommend that you seek assistance during the steps and process shown. This symbol indicates that we recommend that you read the steps, becuase there is important information you should know. Wrench or Rachet aulking Gun & Sealant arpenters Level Rubber Mallet Self Leveling Tape Measure Power Drill Always practice safety! Make sure to wear the right Personal Protection Equipment when working with power tools and Glazing. In accordance with State and Federal Safety Laws, This system is glazed with a Tempered safety glass and if it needs to be replaced for any reason, It should be replaced with the same time and size of glazing. It will be the responsibility of the Owner, Builder, Installer or Sub ontractor which whom will install this Panda Product, to protect the System in its entirety during the installation process. Panda Windows and Doors, will not be responsible for damage which occurred the system while being installed. At no time should any modifications be made to your system, this will Void any warranty on this system. Panel onstruction, Parts Verification,Tools 4 OF 12

5 TS19 TS13 TS87 IS14 S10 S11 S12 S15 S85 Aluminum Thermally Broken System Lift and Slide Glazing removal & Glazing Replacement: Aluminum / Wood Thermally Broken Aluminum Thermally Broken System - Slim Steps to Replace Glazing: (Butted Rails) 1. First you will need to lay panel down on table or something soft to allow the panel to remain un-damaged. 2. Then you will need to remove all glazing gaskets from the panel itself. 3. Finally you will need to remove the bottom rail from the panel by removing the screws anchoring the rail. Slide down and then you will be able to replace the glazing, follow these instructions in reverse to re-assemble the panel. Aluminum - Impact Resistant Aluminum Aluminum / Wood Steps to Replace Glazing:(45 Rails) 1. First you will need to lay panel down on table or something soft to allow the panel to remain un-damaged. 2. Then you will need to remove all glazing gaskets from the panel itself. Solid Wood 3. Finally you will need to remove all glazing clips. These are held in by compression and can be removed by a soft tap with a rubber mallet. Now you will be able to remove glazing, follow instruction in reverse to re-assemble. Lift and Slide Panel(s): Panda Windows and Doors has spent countless hours on designing many different types of systems with specially designed panels. Above you will notice the wide selection of Lift and Slide panels. You will find systems that offer thermal control and still will offer the look that you desire. Each Panel profile has a wall thickness that will allow for the strength and security that you would look for in our systems. Solid Wood / Aluminum ore Lift and Slide Panel Selection / Types 5 OF 12 Aluminum Slim Profile

6 Installation Step 1 - (Lift and Slide Systems): Installation Step 2 - (Lift and Slide Systems): Rough Opening Width Rough Opening Height Depth Basic Tools Required For These Steps: Installation Step 2: Shim Blocking Screw Installation for Leveling arpenters Level Tape Measure Power/Impact Drill Shimming & leveling the system properly is highly important, do not over or under shim Please read these instructions in their entirety before starting install First before checking the dimensions for your systems, Ensure that your opening is sqaure and plumb. Then go use a tape measure and check the dimensions of the height, width and your dimension across your opening as shown in (figure 1) above. After this step is complete then it will be time to dry fit your system to assure that it will fit in the opening per the dimensions that were given to your sales assistant at the time of ordering. Go ahead and take the Header track and and side frames into the opening. After those are in you should have at least 1/2" shim space on both ends. Once you have tested to assure the header and side frames fit, Then if your system is Equipped with a bottom track, go ahead and place that in the opening as well. The bottom track is cut to the exact same size of your overall system width, Panda Window's & Door's does not recommend you to modify this system. These Lift and Slide systems are made to the order and are custom to the customer's specification's. Any alterations made to this system by an unlicensed representative, will void the warranty... Once you have dry tested your system and assured that everything fit properly, Now it will be time to prepare your opening for your new system. If your opening needs to be shimmed, go ahead and apply your shims as necessary. You should still have atleast 1/2" of clearance around your entire system. heck your entire opening to insure that the opening is level and square. This is one of the most important steps and should not be passed, to ensure proper operation of your new system. Rough Opening Dimension Verification 6 OF 12

7 Installation Step 3: System Bottom Track Installation VERIFY WIDTH VERIFY DEPTH Track Installation Step A: Double check your trench depth and width with the actual bottom track provided. Your trench depth should have an extra 1/2" shim space provided below the track system setup. *(Depth varies due to different track types) Track Installation Step B: Insert Track into floor depression to assure the sizing is correct (make sure the track is the same size all the way from end to end from edge of slab, Also check the track height to assure that you can still acheive the 3/16" lip required. Track Installation Step : Use the track and the provided pilot holes in the track arms as a guides and drill holes for anchor bolts (holes must be 3/8" dia. and 1" Deep) Into the concrete trench to make ready for installation of your anchors. Track Installation Step D: Remove track and drop your anchors receivers into there holes. (1/4" x 20 Drop In-Anchors), next you will have to cut your threaded 1/4" rod to be inserted into your inserted anchors. Track Installation Step E: Insert your precut 1/4" threaded rod into the installed anchor receivers and then attach flat washer and nut, adjust height to achieve 3/16" from finish floor. Reinstall track after complete Basic Tools Required For These Steps: Track Installation Step F: Adjust and tighten the nuts shown above to anchor the track into place, assure that the system is level as your are tightening the track down. Track Installation Step H: Once track is placed on to leveled and the anchor bolts have been secured into there proper place and height. Then your will have to use a level (Laser Level recommended) to assure the track is completely leveled. (See Below for finishing) Bottom Track installation With Drain Ports (Drainage tubes if system is equipped with a drainage track.) Track Installation Final: When the track is at correct height and the system has been completely tested with panels. Then you will want to finish the track to your desired finish. Make sure you have a 3/16" lip exposed for systems wheels to glide smoothly along the system tracks. arpenters Level Wrench/Rachet Power Drill aulking Gun & Sealant Tape Measure Please read these instructions in their entirety before starting Bottom Track install The anchorage and leveling of the bottom track is highly important to ensure proper operation and life span of your Lift and Slide System(s). Double check all bottom track and upper tracks to ensure proper anchorage and proper leveling, that way the panels slide as they were designed to do. Please keep in mind that pilot holes are already pre-drilled in the headers, side frames and bottom tracks. It is highly important that the your rough opening and substrate that the sytem track will be installed to is level and clean and free of debris. Do not drill any new support holes into the systems tracks. Be sure that you use proper size anchorage bolts, to allow clearance for the Lift and slide wheels to glide freely throughout the Systems tracks. (4" Installation screws will be provided with this system, Other anchorage bolts will be customers expense) When Installing a system equipped with a Panda certified bottom track, It is most important to insure proper installation and sealing of the bottom track. Assure the trench that the bottom track will be set into, is clean and free of any sort of debris. Dry fit your bottom track to assure proper trench and track size. Then fill your trench with the proper amount of self leveling epoxy or equivalent. Once the track is set into the trench you will want to install the proper track screws (Which are provided with the System).. Note: Different anchors may be required depending on substrate. (Account for your drainage tubes, saw cut your slab or prep your substrate to your desire locations) Tracks with drainage ports are available, Make sure when cutting your slab or preparing your substrate that you account for the routing of the drainage tubes. (Drain Ports are pre-installed at factory, choose port type when ordering) Bottom Track Types & Drain Tube Types *Straight Drain Port and tube* *90 Drain Port and tube* Bottom Track Installation 7 OF 12

8 Installation Step 5A: System Side Frame Installation Installation Step 5B: At Header Track Installation Step 5: At Bottom Track Side Frame Note: Header can be attached to side frames and tilted into opening if install choses to install in this manner. Basic Tools Required For These Steps: Angle Side Frame And Slide Into Header Track Installation Step 5D: Side Frame Sealing At bottom Track Align Side Frame Notches to Bottom Track arpenters Level Power/Impact Drill aulking Gun & Sealant Please read these instructions in their entirety before starting Header Install Panda Window's And Door's is not responsible for the support structure which the system will be attached to. The structure that the system will be attached to, should be specified by a licensed engineer which is not in Panda's Window's and Door's Scope of work. Please read these instructions in their entirety before installing bottom Track Once the previous steps are completed, you will want to apply a consistent bead of construction sealant at each end of the track, Then you will set the side frames into the sealant and drill screw into each pilot hole provided. The screws for you side frame will be provided by Panda as well. heck to make sure the side frames and bottom tracks are level. (Laser Level recommended) When installing the side frames, review the side frames that are included with your system, there are a few different types. Make sure that you are installing the right side frame in the correct location, install the frame using the anchor screws included. Apply a small bead of sealant around the track where the side frame will be installed. Then set the side frame into the bead of sealant and anchor the side frames to the structure. Please read before the installation of the Side Bottom Tracks When installing these system side frames, please assure that you have a good seal at the bottom and the top of the track before screwing them into place with provided anchor screws. Dry fit the side frames provided to assure that they fit to the dimensions that you provided to us at the time of ordering. If the bottom track is recessed, apply sealant to conrete at time of placement. Installation of Header & Side Frames 8 OF 12

9 Installation Step 6: Typical Lift and Sllide Panel Installation For all Systems The slot in the upper panel allows the panel to slide into the upper track. Slot cover provided These interlocks allow the panels to catch the next panel during operation. It also allows the panel to stay securley closed Step A: Insert your first panel and either lock or screw to side jamb (To secure first panel in place)(opt) Step B: Insert your second panel and make sure that your interlocks overlap (that way the interlocks catch) Step : Insert your final panel and engage your handle by rotating 180 (Make sure your interlocks overlap) Basic Tools Required For These Steps: Mechanisms Optional Handle Hardware: Handle Mechanism arpenters Level Tape Measure Power Drill Wheel Mechanism This Section Will Require Assistance During the Installation of each panel, proper lifting and saftey measure should be taken. That way the Ultra Panel's, System and adjacent area are not subjected to any sort of damage. Also the person's installing the system are kept safe. Please read these instructions entirety before installation of panels Once the Header, Side frames and Bottom Tracks are installed, Then it will be time for the installation of each panel. This is the part that Panda advices you to ask for assistance from a fellow coworker. Each one of these system panel's can way upwards of 300lbs and can be very difficult to maneuver. Also, When installing each panel you will need to assure that you are setting the panels wheel sets onto the lower track, otherwise the system will not operate correctly. Each panel comes from the factory already tested to ensure proper operation of each panel and wheel mechanism. When installing the panel you will need to make sure that you insert the panels to where the panel interlocks will be on the proper sides of each other, (refer to diagram). If the panels are inserted to the were the interlocks are on the incorrect sides of the panels. The system will not operate correctly and may cause damage to the system if you try to operate. Lift and Slide Hardware is Specially Designed to go hand and hand with supplied optional handles. Other handle options would have to be approved by designed team to insure operation use. Please insure that the wheel mechanism is level and equal on the track Installation Of System Panels 9 OF 12

10 Installation Step: System With Pocket Installation Installation Step: Pocket Installation Details Exterior Side of Pocket: Finished pocket door opening Interior Side of Pocket: Finished pocket door opening Bottom track of Pocket: Follow typical bottom track install instructions, track runs depth of pocket Basic Tools Required For These Steps: arpenters Level Wrench/Rachet Power Drill Header track of Pocket: Follow typical Header track install instructions, track runs depth of pocket aulking Gun & Sealant Tape Measure Track Installation Step A: After you follow the normal steps for the header and bottom track install. You will then want to insert your first pocket panel, This panel will have the pocket board combo piece already attached, Follow typical panel installation. Track Installation Step B: Once are your panels are installed correctly and as instructions specify, then you will want to install the exterior side interlock clip. This piece will anchor straight to your wall, and can be covered with a finish per adjacent wall. ANHORAGE SREWS YOU SHOULD HAVE 1/4" LEARANE FROM FINISHED WALL TO BOARD EXTERIOR POKET INTERLOK LIP PANEL INTERLOK LIP PANEL INTERLOK LIP BRUSHED GASKET PANEL INTERLOK LIP FITS FLUSH TO WALL Please read these instructions in their entirety before starting Pocket system install The installation of your pocketing system is similar to a normal system installation. But there are certain other steps and procedures that need to be followed. First when installing your bottom track, side frame and header you will follow the standard installation steps since there is no difference between these installations. If you have a bi-parting pocketing system you will have no side frames, instead you will have two (2) pocket board interlock setups for each side of the system. Follow the steps as if you were installing one (1) pocket. Steps for this type of installation is the same. Pocketing systems can be setup many different configurations and needs to be determined during the design process. A normal install requires an extra five (5) inches added onto your panel length for determining your pocket depth. For your pocket width you will have to review back to your design drawings, since all systems pocket widths will vary. Also for a standard pocket install your handle will not recess into the pocket unless asked for at the time of ordering. Follow each step on this page for the installation of your pocket interlock setup and enjoy. Track Installation Step : Finally, you will have to attach your pocket board to the rest of the system. Place the pocket board against the 2x4 triangle anchorage peices, use provided #4 screws to attach. The Brushed gasket side goes to the interior wall side. This completes your pocket system install. POKET BOARD BRUSHED GAKSET WOOD POKET BOARD 2X4 ALUMINUM PROFILE FOR POKET BOARD ANHORAGE Pocket Board Parts: Above you will see all the parts that make up the pocket board interlock combo for this system. Some Parts are pre-installed at factory System With Pocket Installation 10 OF 12

11 Installation Step 7A: System Finishing Installation Step 7B: System Finishing ase of Backer Rod * Install construction grade backer rod into the joint around the systme to fill those caulk joints before applying sealant (Optional) Basic Tools Required For These Steps: *Be Sure to seal around your system on the inside and outside with a construction sealant- Use either a silicone or latex based sealant depending on the location and install type. Installation Step 7: Sealing around System aulking Gun & Sealant ase of Backer Rod Sealant Backer Rod Please read these instructions in their entirety before sealing your System Once all of the steps are completed and your new systems is installed, It is time to properly seal your system. Panda Windows and Door's Recommends the use of a solvent release butyl rubber sealant or equal. (Sealant Recommendation: DAP DyanFlex 230) Regular Operation of This is system All the Lift and slide systems that Panda Window's and Door's have created are very simple and easy to operate. After the installation process is completed and the system is sealed in it's entirety, it will be time to test the system for first time. First, You will want to unlock the system and open the system all the way. During this process, you will want to assure that the system open's with no rubbing and/or grinding. Simply rotate the installed handle and slide the system to the open position. The system should glide real easily along the installed bottom track. If there is any resistance, please remove the panels and assure that the system was installed properly. Level installation of this system is highly important to ensure proper normal operation. To lock the system, Simply slide end panel against side frame and rotate the handle, which will drop the panel and lock the panel to the side frame. Make sure you have a consistent bead of sealant to ensure proper sealing Final Finishing Of System 11 OF 12

12 Final Installation Step: System Maintenence For Service Questions & oncerns: Please ontact Us Please read these instructions below for System Maintenence Typical Area Maintenance: Areas located with in normal weather areas arent subject to the salted water of the costal areas, but still require some maintenence to ensure a longer life for the system. There are still the harsh enviroments were you will have the cold and snow, which will take its tools on any products and materials over an extended period of time. ostal Area Maintenance: Areas that a located within a 2 mile radius area of a costal area, can be extremely corrosive. Any type of material or products that are located in this radius, tend to get corrosive sooner then your typical environment. That is why Maintenance once and while is recommended. Follow these steps below to ensure a longer life span of your system: Follow these steps below to ensure a longer life span of your system: 1.) Inspect your system once and a while and if you notice that the finish on your system has been scratched, nicked or chipped. Please make sure that you contact your sales manager. That way you can see your options to get them fixed as soon as possible. 1.) Inspect your system once and a while and if you notice that the finish on your system has been scratched, nicked or chipped. Please make sure that you contact your sales manager. That way you can see your options to get them fixed as soon as possible. 2.) At least every 6 months look over your system and clean debris from the bottom track and header track, that way you can ensure there is nothing blocking the systems wheels. As well, check the caulking and sealant to ensure the system is still sealed properly. If you need to replace the sealant, cut and remove old sealant and reapply. 3.) At least every 6 months you should go over your system and use Teflon spray to lubricate wheels and bearings of the system. 4.) Shifting of the building may make need to have your certified installer adjust the panels. 2.) At least every 6 months look over your system and clean debris from the bottom track and header track, that way you can ensure there is nothing blocking the systems wheels. 3.) Spray down your system with mild soap fresh water to clean and free any salted water or residue that remains on your system, at this same time you should use a Teflon spray to lubricate wheels and bearings of the system. 4.) Shifting of the building may make need to have your certified installer adjust the panels. Glass are: Use a non abrasive soft Terry loth and ammonia free cleaner on the glass as needed. System Maintenance 12 OF 12