G632:G581 JR12 CI/SfB (52.7) In6 June 2015 OWIC001. Water management PRODUCT AND INSTALLATION MANUAL. Wavin. Inspection Chambers

Transcription

1 Water management PROUT N INSTLLTION MNUL Uniclass EPI G632:G581 JR12 I/Sf (52.7) In6 June 2015 OWI001 J34 Inspection hambers Wavin Inspection hambers

2 ontents Osma/Wavin hambers Introduction 2 The Osma/Wavin Non Man-Entry Inspection hamber Range 2 Material 2 Standards 2 cceptance 2 General Information 3 Range Overview 4 Osma Inspection hambers Shallow 4 Wavin Inspection hambers eep 4 Product etails Osma 5 23 Inspection hambers Shallow Shallow I 5 7 Multi-ase I 8 12 Universal I Non Man-Entry I Installation Osma Inspection hambers Shallow Shallow/Multi-ase I Universal/Non Man-Entry I Product etails Wavin Inspection hambers eep Range 200 I Range 315 I Range 450 I Range 600 I Installation Wavin Inspection hambers eep Range 200 I Range 315 I Range 450 I Range 600 I Typical ackdrop onnection 57 Ranges 315, 450 and 600mm I 57 Testing and Maintenace 58 Testing 58 Maintenance technical.design@wavin.co.uk Osma/Wavin hambers PIM 1

3 Introduction Osma/Wavin hambers The Osma/Wavin Non Man-Entry Inspection hamber Range The Osma/Wavin range of Non Man-Entry Inspection hambers are designed for use in gravity drainage installations and are offered for connections to pipe diameters: 110mm, 150/160mm, 225mm and 300mm. The Osma/Wavin range of chambers offers a number of base and shaft configurations to gain access to underground drainage pipelines, giving Specifiers and Installers the freedom to choose the most suitable system for their needs. The alternatives available are: Inspection hambers Shallow For use at a maximum invert depth of 0.6 metres in uilding ontrol applications and/or 0.9 metres in Sewers for doption 7 (Sf7) applications. (Multi-ase range only). Inspection hambers eep For use at a maximum invert depth of 1.2 metres in uilding ontrol applications and 3.0 metres in Sewers for doption 7 (Sf7) applications. Standards a ritish Standards Institution The Osma/Wavin range of Non Man-Entry Inspection hambers comply where applicable with the requirements of the following ritish Standards: S EN 124:1994 Gully tops and manhole tops for vehicular and pedestrian areas. S EN Parts 1 & 2 Plastics piping systems for nonpressure underground drainage and sewerage. S 7158:2001 Plastic inspection chambers for drains and sewers- Specification. cceptance The Osma/Wavin range of Non Man-Entry Inspection hambers are included in the following publication:- Sewers for doption, 7th Edition, under clause E2.31. Material a) Inspection hambers Polypropylene is used in the manufacture of the majority of the Osma/Wavin Non Man-Entry Inspection hamber range. b) Sealing Rings Snap-ap-Polypropylene and Sealing Ring TPE. 2 Osma/Wavin hambers PIM ustomer Services: Technical dvice:

4 General Information Osma/Wavin hambers escriptions escriptions and illustrations in this publication are for guidance only. No responsibility can be accepted for any errors, omissions or incorrect assumptions. Refer to the product itself if more detailed information is required. ue to the continuing programme of product improvement, Wavin reserves the right to amend any published information or to modify any product without prior notice. imensions Unless otherwise stated all dimensions are in millimetres (mm). Symbols a) ritish Standard Kitemark a Identifies chambers which are manufactured under the.s.i. ertification Scheme. b) ritish oard of grément $ Identifies Non-Kitemarked fittings which are covered by a ritish oard of grément ertificate. olour Most Inspection hambers lack Ring Seals lack Supply ll Osma/Wavin Non Man-Entry Inspection hambers are supplied through a nationwide network of merchant distributors. For further information contact ustomer Services on Technical dvice The Osma/Wavin Non Man-Entry Inspection hamber Range is backed by Wavin s comprehensive technical advice service. This is available to provide expert assistance at every stage of a project, from planning and product selection to installation and maintenance. Literature The following Wavin publications are also available from the Literature epartment at hippenham. General Wavin elow Ground & ivils System: Trade Price List Gravity rain and Sewer Systems Osmarain System: Product and Installation Guide Osma UltraRib System: Product and Installation Guide Osma Non Man-Entry Inspection hamber Range: Product and Installation Guide Stormwater Management Systems Wavin quaell System: Product and Installation Guide Wavin Flow ontrol Range: Product and Installation Guide Wavin ommercial Rainwater Re-use System: Product Summary Wavin Poly-oncrete hannel Systems: Product and Installation Guide Wavin Quickstream Siphonic Roof rainage Systems: Product and Installation Guide To request details with regards to any of the above components and/or for any technical enquires please contact: Literature Request Tel: literature@wavin.co.uk Technical esign Tel: technical.design@wavin.co.uk Wavin Online The complete range of Osma/Wavin product and installation guides are also available online at: wavin.co.uk ontact Wavin Technical esign epartment: Tel: technical.design@wavin.co.uk or via online enquiry at wavin.co.uk technical.design@wavin.co.uk Osma/Wavin hambers PIM 3

5 Range Overview Osma/ Wavin hambers The Osma/Wavin Non Man-Entry Inspection hamber Range offers a comprehensive portfolio of inspection chambers which can provide the optimum solution for every adoptable and non-adoptable situation, within the uilding and onstruction markets. See Osma Inspection hambers Shallow for, components complying to S EN See Wavin Inspection hambers eep for, components complying to S EN Osma Inspection hambers Shallow ase Type Shallow I Multi-ase I Universal NI Max Invert epth (m) ase/shaft ia (mm) Sf7 Type No of inlets 1 l 1 to 3 l l l l 4 to 5 l l Inlet Sizes (mm) / /160 Kitemarked to: S EN l l l S EN 7158 l Note 1: Under Sf7 maximum permitted depth can be increased from 0.6m to 0.9m Note 2: Under S 7158:2001 maximum permitted depth is 3m Wavin Inspection hambers eep ase Type Range 200 Range 315 Range 450 Range 600 Max Invert epth (m) ase/shaft ia (mm) Sf7 Type No of inlets 1 l l l l 1 to 3 l l l 4 to 5 l Inlet Sizes (mm) 110/ / / /225/300 Kitemarked to: S EN l S EN l l l Note 1: Under Sf7 maximum permitted depth can be increased from 0.6m to 2.0m Note 2: Under Sf7 maximum permitted depth can be increased from 1.2m to 3.0m Product and Installation details for Osma Inspection hambers Shallow are shown in the orange section and Wavin Inspection hambers eep are shown in the blue section of this booklet. 4 Osma/Wavin hambers PIM ustomer Services: Technical dvice:

6 Product etails Shallow I Introduction escription 250mm diameter polypropylene inspection chamber for adoptable and non-adoptable applications. ompliant with Sewers for doption 7th edition [Sf7]. Single unit with integral shaft, for use with 110mm Osmarain system. Shaft may be cut to length to achieve required invert depth. pplications For above ground access and maintenance inspection of buried pipework up to 0.6 metres deep For loading applications up to 10kN (1.0 Tonne) Key imensions External shaft diameter: 250mm Inlets/outlets: 110mm Key Features & enefits Fast, easy installation: no wet trades Lightweight: no lifting equipment required Shaft can be cut to required length No additional trench excavation required ompliance The Shallow Inspection hamber complies with the following standards and regulations S EN : 2010 a Sf7 Typical hamber etail Type 4: (to max. 0.6m depth only) uilding Regulations Part H1: Shallow only, to maximum depth 0.6m Shallow Inspection hamber assembly technical.design@wavin.co.uk Osma/Wavin hambers PIM 5

7 Product etails Shallow I Shallow Inspection hamber Maximum invert depth 0.6m. whether used in adoptable or non-adoptable applications. /S Equal Shallow Inspection hamber E G F 250mm dia. base with integral shaft, incorporating straight channel and three inlets, including 2 x 45 equal branch inlets For use with 110mm Osmarain Supplied with two profiled blank-off plugs for unused side entries Size (mm) Number E F G over & Frame Round over & Frame For non-trafficked/landscaped locations Sealed For loadings up to 10kN (1.0 tonne) when supported by a concrete collar an be used internally Size (mm) Number Square over & djustable Frame For non-trafficked/landscaped locations Sealed For loadings up to 10kN (1.0 tonne) when supported by a concrete collar an be used internally Size (mm) Number Osma/Wavin hambers PIM ustomer Services: Technical dvice:

8 Spares over to Frame Seal 250mm diameter for use with 4325 and 4961 overs & Frames Material: EPM Nominal Part Size (mm) Number 4314 Screws Pack of 4 for securing 4325/4961 cover to its frame Material: Metal Nominal Part Size (mm) Number 4318 Round over Spare for use with 4325 and 4961 Frame Nominal Part Size (mm) Number 4328 lank-off Plugs For use with 4960 Nominal Part Size (mm) Number technical.design@wavin.co.uk Osma/Wavin hambers PIM 7

9 Product etails Multi-ase I Introduction escription 315mm diameter polypropylene inspection chamber for adoptable and non-adoptable applications. ompliant with Sewers for doption 7th edition [Sf7]. hoice of ten base configurations for use with 110mm Osmarain system. Shaft may be assembled to required invert depth by using shaft sections pplications For above ground access and maintenance inspection of buried pipework own to 0.6m deep under uilding Regulations Part H1 own to 0.9m deep under Sf7 Typical hamber etail Type 4 For loading applications up to 15kN (1.0 Tonne) Key imensions Invert depth of base: 205mm External shaft diameter: 315mm Shaft section length: 150mm Inlets/outlets: 110mm Key Features & enefits Multiple options for maximum installation flexibility Fast, easy installation: no wet trades Lightweight: no lifting equipment required Push-fit shaft sections: one or more can be used to achieve required invert depth Final shaft section can be cut to required length No additional trench excavation required ompliance Multi-ase Inspection hambers comply with the following standards and regulations S EN : 2010 a Sf7 Typical hamber etail Type 4 (to max. 0.9m depth only) uilding Regulations Part H1: Shallow only, to maximum depth 0.6m Multi-ase Inspection hamber assembly 8 Osma/Wavin hambers PIM ustomer Services: Technical dvice:

10 Multi-ase Inspection hamber ases When used in non-adoptable applications, maximum invert depth 0.6m. When used in adoptable applications, maximum invert depth 0.9m. E F /S Equal Shallow Inspection hamber ase 315mm dia. base incorporating straight channel and single inlet For use with 110mm Osmarain Size (mm) Number E F a E F /S Equal Shallow Inspection hamber ase 315mm dia. base incorporating straight channel and two inlets including 90 left-hand equal branch inlet For use with 110mm Osmarain Size (mm) Number E F a E F /S Equal Shallow Inspection hamber ase 315mm dia. base incorporating straight channel and two inlets including 90 right-hand equal branch inlet For use with 110mm Osmarain Size (mm) Number E F a E F /S Equal Shallow Inspection hamber ase 315mm dia. base incorporating straight channel and two inlets including 45 left-hand equal branch inlet For use with 110mm Osmarain Size (mm) Number E F a technical.design@wavin.co.uk Osma/Wavin hambers PIM 9

11 Product etails Multi-ase I E F /S Equal Shallow Inspection hamber ase 315mm dia. base incorporating straight channel and two inlets including 45 right-hand equal branch inlet For use with 110mm Osmarain Size (mm) Number E F a E G F /S Equal Shallow Inspection hamber ase 315mm dia. base incorporating straight channel and 3 inlets including 2 x 45 equal branch inlets For use with 110mm Osmarain Size (mm) Number E F a E F /S Equal Shallow Inspection hamber ase 315mm dia. base incorporating 90 bent channel and single inlet For use with 110mm Osmarain Size (mm) Number E F a E F /S Equal Shallow Inspection hamber ase 315mm dia. base incorporating straight channel and three inlets including 45 and 90 left-hand equal branch inlets For use with 110mm Osmarain Size (mm) Number E F a Osma/Wavin hambers PIM ustomer Services: Technical dvice:

12 E F /S Equal Shallow Inspection hamber ase 315mm dia. base incorporating straight channel and three inlets including 45 and 90 right-hand equal branch inlets For use with 110mm Osmarain Size (mm) Number E F a E F /S Equal Shallow Inspection hamber ase 315mm dia. base incorporating straight channel and three inlets including 2 x 90 equal branch inlets For use with 110mm Osmarain Size (mm) Number E F a Shaft P/E Inspection hamber Shaft 315mm diameter x 150mm long For use with all types of Multi-ase 315mm bases Supplied with a pre-fitted elastomeric seal Size (mm) Number a * *imension = effective height over & Frame Square over & djustable Frame For non-trafficked/landscaped locations For loadings up to 15kN (1.5 tonnes) when supported by a concrete collar For external use only Size (mm) Number technical.design@wavin.co.uk Osma/Wavin hambers PIM 11

13 Product etails Multi-ase I Spares Multi-ase Shaft Seal 315mm diameter for use with 4937 shaft sections Material: EPM Nominal Part Size (mm) Number Osma/Wavin hambers PIM ustomer Services: Technical dvice:

14 Product etails Universal I Introduction escription 450mm diameter polypropylene inspection chamber for adoptable and non-adoptable applications. ompliant with Sewers for doption 7th edition [Sf7]. hoice of five base configurations for equal and unequal pipe connections. ase configurations available for use with either 110/160mm Osmarain or 150mm UltraRib. Shaft may be assembled to required invert depth by using shaft sections 4975 (maximum 1.2m). pplications For above ground access and maintenance inspection of buried pipework up to 1.2 metres deep For loading applications up to 15kN (1.5 tonnes) Key imensions Height of bases: 295mm [for 110mm system] 270mm [for 150mm and 160mm systems] External shaft diameter: 450mm Shaft section length: 305mm Maximum installation depth: 1.2m Key Features & enefits Fast, easy installation: no wet trades Lightweight: no lifting equipment required Push-fit shaft sections: one or more can be used to achieve required invert depth Final shaft section can be cut to required length No additional trench excavation required ompliance Universal Inspection hambers comply with the following standards and regulations S EN : 2010 a Sf7 Typical hamber etail Type 4 (to max. 1.2m depth only) uilding Regulations Part H1: Shallow and/or eep Universal Inspection hamber assembly technical.design@wavin.co.uk Osma/Wavin hambers PIM 13

15 Product etails Universal I Universal Inspection hambers 450mm Shaft When used in adoptable/non-adoptable applications, maximum invert depth 1.2m. E F /S Equal Inspection hamber ase 450mm dia. base incorporating straight channel and 5 inlets including 2 x 45 and 2 x 90 equal branch inlets For use with 110mm Osmarain Supplied with 3 blank-off plugs for unused side entries Size (mm) Number E F a * *Note: dimension F = height at centre point of base (all bases have a 15 inlet-to-outlet fall) E F /S Equal Inspection hamber ase 450mm dia. base incorporating straight channel and 3 inlets including 2 x 90 equal branch inlets For use with 160mm Osmarain Supplied with 1 blank-off plug for unused side entry Size (mm) Number E F a * *Note: dimension F = height at centre point of base (all bases have a 15 inlet-to-outlet fall) E F /S Equal Inspection hamber ase 450mm dia. base incorporating 160mm straight channel and 5 inlets including 2 x 45 and 2 x mm branch inlets For use with 110mm and 160mm Osmarain Supplied with 3 blank-off plugs for unused side entries Size (mm) Number E F a * *Note: dimension F = height at centre point of base (all bases have a 15 inlet-to-outlet fall) 14 Osma/Wavin hambers PIM ustomer Services: Technical dvice:

16 E /S Equal Inspection hamber ase straight channel with two 90 branches (left and right) F 450mm dia. base incorporating 150mm straight channel and 3 x 150mm inlets including 2 x 90 equal branch inlets For use with 150mm UltraRib Supplied with 1 blank-off plug for unused side entry Size (mm) Number E F 150 6UR928 a * *imension F = height at centre point of base (all bases have a 15 inlet-to-outlet fall) E /S UnEqual Inspection hamber ase straight channel with four branches (two left, two right) F 450mm dia. base incorporating 150mm straight channel and 4 x 110mm inlets including 2 x 45 and 2 x mm branch inlets For use with 150mm UltraRib Supplied with 3 blank-off plugs for unused side entries Size (mm) Number E F 150 6UR929 a * *imension F = height at centre point of base (all bases have a 15 inlet-to-outlet fall) Shaft P/E Inspection hamber Shaft 450mm dia. plain-ended shaft. Length: 305mm For use with all Universal bases Supplied with integral, co-injected, elastomeric seal Size (mm) Number a * *Note: dimension = effective height technical.design@wavin.co.uk Osma/Wavin hambers PIM 15

17 Product etails Universal I over & Frame Options Round over & Frame 125 For medium duty loaded locations For loadings up to 125kN (12.5 tonnes) when frame is supported by a concrete plinth Material: uctile Iron Size (mm) Number 4942 a Square over & Frame 15 Used with 4975 shaft for lightly-loaded locations For loadings up to 15kN (1.5 tonnes) Supplied with 350mm Restricted ccess an be suitable for loadings up to 50kN (5.0 tonnes) when frame is supported by a concrete plinth Size (mm) Number 4920 a * *Note: dimension = fully inserted Round over & Frame 15 Used with 4975 shaft for lightly-loaded locations For loadings up to 15kN (1.5 tonnes) Supplied with 350mm Restricted ccess Size (mm) Number 4924 a * *Note: dimension = fully inserted 16 Osma/Wavin hambers PIM ustomer Services: Technical dvice:

18 Round over & Frame 15 Used with 4975 shaft for lightly-loaded locations For loadings up to 15kN (1.5 tonnes) Size (mm) Number 4927 a * *Note: dimension = fully inserted Square Recessed over & Frame Used with 4975 shaft For loadings up to 25kN (2.5 tonnes) when frame is supported by a concrete plinth Material: Steel cover/polypropylene frame Size (mm) Number Square Recessed over & Frame Used with 4975 shaft Sealed For loadings up to 25kN (2.5 tonnes) when frame is supported by a concrete plinth Suitable for internal use Material: Steel Size (mm) Number ccessories Inspection hamber hannel over left Left-hand for use with 4922 ase only To blank-off unused side entry Nominal Part Size (mm) Number technical.design@wavin.co.uk Osma/Wavin hambers PIM 17

19 Product etails Universal I Inspection hamber hannel over right Right-hand for use with 4922 ase only To blank-off unused side entry Nominal Part Size (mm) Number 4949 over Sealing Ring For sealing 4920/4924/4927 to its corresponding frame Material: EPM Nominal Part Size (mm) Number 4994 Spares Inlet lank-off Plugs For use with all 110mm base inlets Nominal Part Size (mm) Number 4926 Screws for 4920 Pack of 4 for securing 4920 cover to its frame Material: Stainless Steel Nominal Part Size (mm) Number 4995 Screws for 4927 Pack of 3 for securing 4927 cover to its frame Material: Stainless Steel Nominal Part Size (mm) Number Osma/Wavin hambers PIM ustomer Services: Technical dvice:

20 Eye olts for 4920 Pack of 3 for securing 4920 frame to its shaft Material: Stainless Steel Nominal Part Size (mm) Number technical.design@wavin.co.uk Osma/Wavin hambers PIM 19

21 Product etails Non Man-Entry I Introduction escription 500mm diameter polypropylene inspection chamber for adoptable and non-adoptable applications. ompliant with Sewers for doption 7th edition [Sf7]. hoice of three base configurations for equal and unequal pipe connections. ase configurations available for use with either 110/160mm Osmarain or 150mm UltraRib. pplications For above ground access and maintenance inspection of buried pipework For loading applications up to 15kN (1.5 tonnes) Key imensions External shaft diameter: 572mm Maximum installation depth: 1.2m Key Features & enefits Easy to install Lightweight: no lifting equipment required Shaft can be easily cut to required length No additional trench excavation required ompliance The Non Man-Entry Inspection hamber complies with the following standards and regulations S 7158: 2001 a Sf7 Typical hamber etail Type 4: (to max. 1.2m depth only) uilding Regulations Part H1: Shallow and/or eep Non Man-Entry Inspection hamber assembly 20 Osma/Wavin hambers PIM ustomer Services: Technical dvice:

22 Non Man-Entry Inspection hambers 500mm Shaft Inspection hamber 500mm dia. is Kitemarked to S 7158, when used in adoptable areas maximum invert depth is 1.2m, when used in non-adoptable areas, maximum invert depth available under S 7158 is 3m. E F /S Equal Inspection hamber ase 110mm straight channel with two 110mm x 45 and two 110mm x 90 left/right hand branch entries For use with 110mm Osmarain components Supplied complete with a base to shaft sealing ring and 3 blank-off plugs for use in unused side entries Size (mm) Number E F a * *Note: dimension F = height at centre point of base (all bases have a 15 inlet-to-outlet fall) E F /S Equal Inspection hamber ase 160mm straight channel with two 160mm x 90 left/right hand branch entries For use with 160mm Osmarain Supplied complete with a base to shaft sealing ring and 1 blank-off plug for use in unused side entries Size (mm) Number E F a * *Note: dimension F = height at centre point of base (all bases have a 15 inlet-to-outlet fall) E F /S UnEqual Inspection hamber ase 160mm straight channel with two 110mm x 45 and two 110mm x 90 left/right hand branch entries, for use with 110mm components For use with 160mm Osmarain Supplied complete with a base to shaft sealing ring and 3 blank-off plugs for use in unused side entries Size (mm) Number E F a * *Note: dimension F = height at centre point of base (all bases have a 15 inlet-to-outlet fall) technical.design@wavin.co.uk Osma/Wavin hambers PIM 21

23 Product etails Non Man-Entry I E /S Equal Inspection hamber ase F 150mm straight channel with two 150mm x 90 left/right hand branch entries For use with 150mm UltraRib components Supplied complete with a base to shaft sealing ring and 1 blank-off plug for use in unused side entries Size (mm) Number E F 150 6UR936 a * *imension F = height at centre point of base (all bases have a 15 inlet-to-outlet fall) E /S UnEqual Inspection hamber ase F 150mm straight channel with two 110mm x 45 and two 110mm x 90 left/right hand branch entries, for use with 110mm components For use with 150mm UltraRib components Supplied complete with a base to shaft sealing ring and 3 blank-off plugs for use in unused side entries Size (mm) Number E F 150 6UR937 a * *imension F = height at centre point of base (all bases have a 15 inlet-to-outlet fall) Shaft P/E Inspection hamber Shaft 500mm diameter for use with all types of 500mm dia. hamber ases Shaft 1.5m or 3.0m length Size (mm) Number a a Osma/Wavin hambers PIM ustomer Services: Technical dvice:

24 Restriction ccess aps Restriction ccess ap For use with 6934/6938 shaft sections, restricts access to 350mm, supplied with one 500mm sealing ring Size (mm) Number a hamber ase/restriction ccess ap Seal spare 500mm diameter for use with 6934/6938 shaft sections and 6930/940 restriction access caps Material: EPPM Nominal Part Size (mm) Number a NI Telescopic daptor For use with 4920 cover and frame. llows height adjustment and accomodation of slope. Restricted to 350mm internal diameter Size (mm) Number technical.design@wavin.co.uk Osma/Wavin hambers PIM 23

25 Installation Shallow/Multi-ase I Typical Installation of 250/315mm dia. Inspection hambers The following is a typical summary of the installation procedures required to install the Osma 250/315mm dia Inspection hambers. The Shallow and Multi-ase Inspection hamber may be installed in the same minimum trench width as required for standard 110mm drainage pipework. NO extension of trench width is required. ll elements are lightweight: may be handled/installed by a single person. Preparation Prepare and compact 100mm regulating bed of as dug or granular material in trench bottom Positioning/connection Position ase on regulating bed. heck outlet is facing in the correct direction Ensure all inlets/outlet are free from dirt or grit In the case of the Shallow Inspection hamber, remove profile plug(s) for the side outlets required Use standard jointing sequence to connect 110mm Osmarain pipes to inlets/outlet Inspection hamber lean inside of ase socket and lubricate this entire area Position first shaft section into ase socket. Vertically push home manually Push-fit further shaft sections as required for invert depth. Ensure inside of each shaft section is prelubricated ut final shaft section to approximate required height, using a fine-toothed saw. (Grooves at 30mm centres act as cutting guides) ackfill trench Figure 1: Typical installation detail: Shallow Inspection hamber efore starting backfill, cover top of shaft to prevent ingress of dirt or grit Select suitable sidefill use as dug. If not appropriate, use suitable granular material, similar to bedding material void knocking shaft during backfilling and keep free of debris ackfill to formation level. Then trim shaft to required height using finetoothed saw NOTE: If finished ground level is not yet known, leave shaft proud of surface and keep open end covered until final completion (Round) or 4961 (Square) over & Frame NH requirement secure frame to shaft using screws ompacted backfill as dug if suitable, or granular material 4960 Shallow Inspection hamber with 250mm dia. Shaft 110mm Osmarain NOTE: The main through channel MUST be used. ends up to 45 may be used on any inlet or outlet. Granular bedding material utting shaft Shallow Inspection hamber ut shaft to approximate required height, using a fine-toothed saw, using the cutting guides shown on the hamber unit hamfer the cut end to approx. 15 using plain-toothed rasp or scraper Shaft assembly Multi-ase 24 Osma/Wavin hambers PIM ustomer Services: Technical dvice:

26 Figure 2: Typical installation detail: Multi-ase Inspection hamber 4969 over and Frame *For 15 applications subject to occasional loading up to 15kN (1.5 tonnes) (See Figures 4 & 6). ompacted backfill as dug if suitable, or granular material 4937 Inspection hamber Shaft 110mm Osmarain EXMPLE: 250mm Inspection hamber in domestic paths/patios Leave top 150mm of shaft clear of backfill Lay 150mm thick slab of pre-cast or in situ concrete around top of shaft section Prepare polypropylene over and Frame [4325 or 4961] for installation onto and/or into the shaft section, as previously discribed over and Frame: Installation onto/ into 250/315mm dia. Inspection hambers For green areas and pedestrian areas NOT* subject to vehicle loading (See Figures 3 & 5). EXMPLE: 250mm Inspection hamber in domestic gardens Trim shaft section at last stage of construction. Ensure unit is at correct height. Use cutting guides shown on chamber unit Prepare polypropylene over and Frame [4325 or 4961] for installation onto and/or into the shaft section: [4325] lean and lubricate outside of shaft top Ensure sealing ring inside the frame section is seated correctly and free from dirt and grit Position the cover and frame socket over the shaft and push-fit home Fix frame to shaft using self-tapping screws (not provided) [4961] Granular bedding material 4910 Inspection hamber ase lean and lubricate inside of shaft top Ensure sealing ring located on the outside of the frame section is seated correctly and free from dirt and grit Position the cover and frame spigot into the shaft and push-fit home Fix frame to shaft using self-tapping screws (not provided) EXMPLE: 315mm Inspection hamber in domestic gardens Trim shaft section at last stage of construction. Ensure unit is at correct height Lubricate inside of top shaft section Prepare polypropylene over and Frame [4969] for installation into shaft: ensure pre-fitted ring seal is clean and not twisted Position the cover and frame socket into the shaft section and push home Fix frame to shaft using self-tapping screws (not provided) EXMPLE: 315mm Inspection hamber in domestic paths/patios Leave top 150mm of shaft clear of backfill Lay 150mm thick slab of pre-cast or in situ concrete around top of shaft chamber Lubricate inside of top shaft section Prepare polypropylene over and Frame [4969] for installation into shaft: ensure pre-fitted ring seal is clean and not twisted Position the cover and frame socket into the shaft section and push home Fix frame to shaft using self-tapping screws (not provided) [4961] lean and lubricate inside of shaft top Ensure sealing ring located on the outside of the frame section is seated correctly and free from dirt and grit Position the cover and frame spigot into the shaft and push-fit home Fix frame to shaft using self-tapping screws (not provided) technical.design@wavin.co.uk Osma/Wavin hambers PIM 25

27 Installation Shallow/Multi-ase I Figure 3: Installation detail green areas (non-loaded) 4325 (Round) or 4961 (Square) over & Frame NH requirement secure frame to shaft using screws ompacted backfill as dug if suitable, or granular material 4960 Shallow Inspection hamber with 250mm dia. Shaft Figure 4: Installation detail 15 areas subject to occasional vehicle loading up to 15kN (1.5 tonnes) 4961 (Square) over & Frame NH requirement secure frame to shaft using screws 150mm deep concrete collar ompacted backfill as dug if suitable, or granular material 4960 Shallow Inspection hamber with 250mm dia. Shaft Figure 5: Installation detail green areas (non-loaded) 4969 over and Frame 110mm ompacted Osmarain backfill as dug if suitable, or granular material 100mm bedding material 4937 Inspection hamber Shaft Universal Inspection hamber ase Figure 6: Installation detail 15 areas subject to occasional vehicle loading up to 15kN (1.5 tonnes) 110mm Pipe 4969 over and Frame 100mm bedding material mm Inspection deep concrete collar hamber ase 4937 Inspection hamber Shaft ompacted backfill as dug if suitable, or granular material 26 Osma/Wavin hambers PIM ustomer Services: Technical dvice:

28 Installation Universal/Non Man-Entry I Typical Installation of 450/500mm dia. Inspection hamber The following is a typical summary of the installation procedures required to install Osma 450/500mm dia. Inspection hambers. ll elements are lightweight: may be handled/installed by a single person. Excavation Take precautions against trench collapse: support trench sides deeper than 1.2m Shaft assembly 500mm Inspection hamber ut corrugated shaft to approx. Invert depth of hamber. REOMMENTION: leave extra 300mm depth to allow for possible final site changes Locate sealing ring between 2nd and 3rd ribs from shaft bottom. Ensure ring is seated correctly/not twisted lean inside of ase socket and lubricate this entire area Position shaft at 45 angle into ase socket. Vertically push home manually or, if required, with mechanical assistance (if so, protect top of shaft) ackfill trench efore starting backfill, cover top of shaft to prevent ingress of dirt or grit Select suitable sidefill use as dug. If not appropriate, use suitable granular material, similar to bedding material void knocking shaft during backfilling and keep free of debris ackfill to formation level. Then trim shaft to required height using finetoothed saw NOTE: If finished ground level is not yet known, leave shaft proud of surface and keep open end covered until final completion. Preparation Prepare and compact 100mm regulating bed of as dug or granular material in trench bottom Positioning Use standard jointing sequence to connect 110/160mm Osmarain or 150mm UltraRib pipes to inlets/ outlets Push blank-off plugs externally into any unused outlet(s) Figure 7: Typical installation detail: Universal Inspection hamber I over and Frame 4942 S EN Medium uty ar surface 150mm deep concrete collar 4975 Inspection hamber Shaft ompacted backfill as dug if suitable, or granular material NOTE: The main through channel MUST be used. ends up to 45 may be used on any inlet or outlet. Shaft assembly 450mm Inspection hamber lean inside of ase socket and lubricate this entire area Position first shaft section into ase socket. Vertically push home manually Push-fit further shaft sections as required for invert depth. Ensure inside of each shaft section is prelubricated ut final shaft section to approximate required height, using a fine-toothed saw. (Use external rings as cutting guides) 110mm Osmarain Granular bedding material 4922 Universal Inspection hamber ase technical.design@wavin.co.uk Osma/Wavin hambers PIM 27

29 Installation Universal/Non Man-Entry I over and Frame: Installation onto/ into 450/500mm dia. Inspection hambers For green areas and pedestrian areas NOT* subject to vehicle loading (See Figure 8). EXMPLE: 450mm Inspection hamber in domestic gardens Trim shaft section at last stage of construction. Ensure unit is at correct height Prepare selected over and Frame [4920, 4924 or 4927] for installation into shaft Position the cover and frame spigot into the shaft section Fix frame to shaft using self-tapping screws EXMPLE: 500mm Inspection hamber in domestic gardens Trim shaft section at last stage of construction Locate sealing ring (6917) between 2nd and 3rd ribs from shaft top. Ensure ring is sealed correctly, not twisted Prepare NI Telescopic daptor (6940), position over top of shaft and push fully home Prepare selected over and Frame [4920] Position the cover and frame spigot into the Telescopic daptor Fix frame to adaptor using the eyebelts provided *For 15 applications subject to occasional loading up to 15kN (1.5 tonnes) (See Figure 9). EXMPLE: 450/500mm Inspection hambers domestic paths/patios Leave top 150mm of shaft clear of backfill Lay 150mm thick slab of pre-cast or in situ concrete around top of shaft chamber Prepare selected over and Frame [4920, 4924 or 4927] for installation into shaft Position the cover and frame spigot into the shaft section Fix frame to shaft using self-tapping screws Figure 8: Installation detail green areas (non-loaded) For 125 applications subject to medium duty loading up to 12.5kN (12.5 tonnes) (See Figure 10). EXMPLE: 450/500mm Inspection hambers in paved areas with limited traffic load Trim shaft section at last stage of construction. Ensure unit is at correct height Protect shaft from traffic loading by shuttering its external ribs Lay 150mm thick slab of pre-cast or in situ concrete around top of shaft chamber with minimum opening 500mm x 500mm or 500mm diameter to ensure that any loads are distributed away from the shaft On top of slab, construct lass engineering brickwork OR concrete blocks OR pre-cast concrete seating rings up to required height ccording to required loading application, position uctile Iron 125 over and Frame or 400 over and Frame on top of slab PP Square over and Frame 4920 secured to shaft 4975 Inspection hamber Shaft ompacted backfill as dug if suitable, or granular material Figure 9: Installation detail 15 areas subject to occasional vehicle loading up to 15kN (1.5 tonnes) PP Square over and Frame 4920 secured to shaft ar surface 150mm deep concrete collar 4975 Inspection hamber Shaft ompacted backfill as dug if suitable, or granular material 28 Osma/Wavin hambers PIM ustomer Services: Technical dvice:

30 Figure 10: Typical installation detail: 500mm dia Inspection hamber, Type 4 over & Frame lass 125 loading riveway lass engineering bricks set in class 1 mortar 150mm deep concrete collar Shuttering to external cap Restrictor cap 500mm dia to 350mm dia 500mm dia Shaft ompacted backfill as-dug or granular bedding material 100/110mm or 150/160 dia Pipe Granular bedding material technical.design@wavin.co.uk Osma/Wavin hambers PIM 29

31 Product etails Range 200 I Introduction escription 200mm diameter polypropylene inspection chamber for adoptable and non-adoptable applications. ompliant with Sewers for doption 7th edition [Sf7]. For use directly with either 110/160mm plastic pipework or 150mm UltraRib system via the appropriate adaptor (6UR141). 200mm diameter shaft may be cut to length to achieve required invert down to amaximum of 2 metres. pplications For above ground access and maintenance inspection of buried pipework down to 2 metres deep For loading applications: 15 (1.5 tonnes) 125 (12.5 tonnes) * 400 (40 tonnes) * * With cover & frame supported by concrete plinth (suppied by others) Key imensions Invert depth of base: 430mm [for 110mm system] 450mm [for 160mm system] External shaft diameter: 200mm Shaft length: 2m Maximum installation depth: 2m Key Features & enefits Fast, easy installation: no wet trades Lightweight: no lifting equipment required Reinforcing ribs on underside to withstand groundwater pressure Shaft can be cut to required length No additional trench excavation required ompliance Range 200 chambers comply with the following standards and regulations S EN : 2010 a Sf7 Typical hamber etail Type 4: (Non-entry. Maximum depth from cover level to soffit of pipe: 2m) uilding Regulations Part H1: Shallow only to maximum depth 0.6m Range 200 Inspection hamber assembly 30 Osma/Wavin hambers PIM ustomer Services: Technical dvice:

32 ase When used in adoptable applications, maximum invert depth 2m. /S Equal Inspection hamber ase E F 200mm dia. base incorporating straight channel and single inlet For use with 110/160mm plastic pipework systems lso for use with 150mm UltraRib, using daptor 6UR141 Size (mm) Number E F NE300 a NE300 a Shaft P/E Inspection hamber Shaft 200mm dia. plain-ended shaft Length: 2 metres For use with Range 200 bases 24NE300 and 26NE300 Size (mm) Number 20NE * * imension = effective height over & Frame Square over & Frame 15 For non-trafficked/landscaped locations Sealed For loadings up to 15kN (1.5 tonnes) when supported by a concrete plinth Size (mm) Number 20NE technical.design@wavin.co.uk Osma/Wavin hambers PIM 31

33 Product etails Range 200 I ccessories daptor for UltraRib Pipe For connecting 150mm UltraRib pipe to chamber base 26NE300 Size (mm) Number 150 6UR141$ Spares Square over Spare for use with 20NE015 frame Size (mm) Number 20NE Screws Pack of 4 for securing 20NE015 cover to its frame Nominal Part Size (mm) Number Osma/Wavin hambers PIM ustomer Services: Technical dvice:

34 Product etails Range 315 I Introduction escription 315mm diameter polypropylene inspection chambers for adoptable and non-adoptable applications. ompliant with Sewers for doption 7th edition [Sf7]. hoice of eight base configurations for equal pipe connections. For use directly with either 110/160mm plastic pipework or 150mm UltraRib system via the appropriate adaptor (6UR141). ompliance Range 315 chambers comply with the following standards and regulations S EN : 2009 a Sf7 Typical hamber etail Type 4: (Non-entry. Maximum depth from cover level to soffit of pipe: 2m) uilding Regulations Part H1: Shallow only to maximum depth 0.6m 315mm diameter shaft may be cut to length to achieve required invert down to a maximum of 2 metres. pplications For above ground access and maintenance inspection of buried pipework down to 2 metres deep For loading applications: 15 (1.5 tonnes) 125 (12.5 tonnes) * 400 (40 tonnes) * * With cover & frame supported by concrete plinth Key imensions Invert depth of base: 238mm [for 110mm system] 290mm [for 160mm system] External shaft diameter: 315mm Shaft length: 2m Maximum installation depth: 2m Key Features & enefits Fast, easy installation: no wet trades Lightweight: no lifting equipment required Reinforcing ribs on underside to withstand groundwater pressure Shaft can be cut to required length No additional trench excavation required Range 315 Inspection hamber assembly technical.design@wavin.co.uk Osma/Wavin hambers PIM 33

35 Product etails Range 315 I ases ll Range 315 bases are supplied with a base-to-shaft sealing ring. When used in adoptable applications, maximum invert depth 2m. E G F /S Equal Inspection hamber ase 315mm dia. base incorporating straight channel and single inlet For use with 110/160mm plastic pipework lso for use with 150mm UltraRib, using daptor 6UR141 Size (mm) Number E F G NE300 a * NE300 a * 103 * imension F = height at centre point of base (all bases have a 15 inlet-to-outlet fall) E G F /S Equal Inspection hamber ase 315mm dia. base incorporating straight channel and 2 inlets, including 45 left-hand equal branch inlet For use with 110/160mm plastic pipework lso for use with 150mm UltraRib, using daptor 6UR141 Size (mm) Number E F G NE301 a * NE301 a * 103 * imension F = height at centre point of base (all bases have a 15 inlet-to-outlet fall) E G F /S Equal Inspection hamber ase 315mm dia. base incorporating straight channel and 2 inlets, including 45 right-hand equal branch inlet For use with 110/160mm plastic pipework lso for use with 150mm UltraRib, using daptor 6UR141 Size (mm) Number E F G NE302 a * NE302 a * 103 * imension F = height at centre point of base (all bases have a 15 inlet-to-outlet fall) 34 Osma/Wavin hambers PIM ustomer Services: Technical dvice:

36 E G F /S Equal Inspection hamber ase 315mm dia. base incorporating straight channel with 3 inlets, including 2 x 45 equal branch inlets For use with 110/160mm plastic pipework lso for use with 150mm UltraRib, using daptor 6UR141 Size (mm) Number E F G NE303 a * NE303 a * 103 * imension F = height at centre point of base (all bases have a 15 inlet-to-outlet fall) Shaft P/E Inspection hamber Shaft 315mm dia. plain-ended corrugated shaft Length: 2 metres For use with all Range 315 bases Size (mm) Number NE * * imension = effective height over & Frame Square over & Frame 15 For non-trafficked/landscaped locations Sealed For loadings up to 15kN (1.5 tonnes) when supported by a concrete plinth Size (mm) Number 30NE technical.design@wavin.co.uk Osma/Wavin hambers PIM 35

37 Product etails Range 315 I ccessories onnector Kit For connecting 110/160mm plastic pipework to Range 315 Inspection hamber shaft Material: PV-U Nominal Part Size (mm) Number 110 NE NE960 hamber Shaft utter omponents For cutting 110/160mm connection holes to receive plastic pipework in Range 315 Inspection hamber shaft Material: Iron*/Steel Size (mm) Number 110* NE NE daptor for UltraRib Pipe For connecting 150mm UltraRib pipe to all Range 315 Inspection hamber bases Size (mm) Number 150 6UR141$ Spares hamber ase to Shaft Seal 315mm diameter for use with 30NE002 at foot of shaft Material: EPM Size (mm) Number 30NE Osma/Wavin hambers PIM ustomer Services: Technical dvice:

38 over & Frame Seal to Shaft 315mm diameter for use with 30NE002 at top of shaft Material: EPM Size (mm) Number 12TW Square over Spare for use with 30NE015 frame Size (mm) Number 30NE Screws Pack of 4 for securing 30NE203 cover to its frame Nominal Part Size (mm) Number 30NE technical.design@wavin.co.uk Osma/Wavin hambers PIM 37

39 Product etails Range 450 I Introduction escription 450mm diameter polypropylene inspection chamber for adoptable and non-adoptable applications. ompliant with Sewers for doption 7th edition [Sf7]. hoice of eight bases for equal and unequal pipe connections. ompliance Range 450 chambers comply with the following standards and regulations S EN : 2009 a Sf7 Typical hamber etail Type 3: (Non-entry. Maximum depth from cover level to soffit of pipe: 3m) uilding Regulations Part H1: Shallow and/or eep edicated bases for use directly with either 110/160mm plastic pipework or 150mm UltraRib system via the appropriate adaptor (6UR141). 450mm diameter shaft may be cut to length to achieve required invert up to maximum 3 metres. pplications For above ground access and maintenance inspection of buried pipework up to 3 metres deep For loading applications: 15 (1.5 tonnes) 125 (12.5 tonnes) * 400 (40 tonnes) * * With cover & frame supported by concrete plinth NOTE: oncrete plinth not required for non-loaded applications such as domestic gardens Key imensions Invert depth of bases: mm (at centre point of base) External shaft diameter: 515mm Shaft length: 3m Maximum installation depth: 3m Key Features & enefits Full range of dedicated bases, ensure that smooth flow can be achieved Quick & easy to install, with a sculpturedneck on the base, which allows the shaft to be fitted with little effort Lightweight polypropylene chamber bases, no lifting equipment required 3m shaft can be cut to required length Range 450 Inspection hamber assembly 38 Osma/Wavin hambers PIM ustomer Services: Technical dvice:

40 ases For use with 110mm plastic pipework ll Range 450 bases are supplied with a base-to shaft sealing ring. When used in adoptable applications, maximum invert depth 3m. /S Equal Inspection hamber ase 450mm dia. base straight channel and single inlet Size (mm) Number E NE300 a /S Equal Inspection hamber ase 450mm dia. base incorporating straight channel with 3 inlets, including 1 x 45 and 1 x 90 left-hand, equal branch inlets Supplied with 1 x 110mm blank-off plug Size (mm) Number E NE304 a /S Equal Inspection hamber ase 450mm dia. base incorporating straight channel with 3 inlets, including 1 x 45 and 1 x 90 right-hand, equal branch inlets Supplied with 1 x 110mm blank-off plug Size (mm) Number E NE305 a /S Equal Inspection hamber ase 450mm dia. base incorporating straight channel with 5 inlets, including 2 x 45 and 2 x 90 left/right-hand, equal branch inlets Supplied with 3 x 110mm blank-off plugs Size (mm) Number E NE306 a technical.design@wavin.co.uk Osma/Wavin hambers PIM 39

41 Product etails Range 450 I ases For use with 160mm plastic pipework ll Range 450 bases are supplied with a base-to shaft sealing ring. When used in adoptable applications, maximum invert depth 3m. /S Equal Inspection hamber ase 450mm dia. base straight channel and single inlet lso for use with 150mm UltraRib, using daptor 6UR141 Size (mm) Number E NE300 a /S UnEqual Inspection hamber ase 450mm dia. base incorporating 160mm straight channel with 3 inlets, including a 110mm x 45 and a 160mm x 90 lefthand, equal branch inlets Supplied with 1 x 110mm blank-off plug lso for use with 150mm UltraRib, using daptor 6UR141 Size (mm) Number E NE307 a /S UnEqual Inspection hamber ase 450mm dia. base incorporating 160mm straight channel with 3 inlets, including a 110mm x 45 and a 160mm x 90 righthand, equal branch inlets Supplied with 1 x 110mm blank-off plug lso for use with 150mm UltraRib, using daptor 6UR141 Size (mm) Number E NE308 a Osma/Wavin hambers PIM ustomer Services: Technical dvice:

42 /S UnEqual Inspection hamber ase 450mm dia. base incorporating 160mm straight channel with 5 inlets, including 2 110mm x 45 and 2 160mm x 90 left/righthand, equal branch inlets Supplied with 2 x 110mm and 1 x 160mm blank-off plugs lso for use with 150mm UltraRib, using daptor 6UR141 Size (mm) Number E NE309 a Shaft P/E Inspection hamber Shaft 450mm dia. plain-ended corrugated shaft Length: 3 metres For use with all Range 450 bases Size (mm) Number NE * * imension = effective height Restriction ccess ap Restriction ccess ap For use with 40NE300 shaft Restricts access to 350mm Supplied with one 450mm sealing ring Size (mm) Number NE technical.design@wavin.co.uk Osma/Wavin hambers PIM 41

43 Product etails Range 450 I ccessories onnector Kit For connecting 110/160mm plastic pipework to Range 450 Inspection hamber shaft Material: PV-U Nominal Part Size (mm) Number 110 NE NE960 hamber Shaft utter omponents For cutting 110/160mm connection holes to receive plastic pipework in Range 450 Inspection hamber shaft Material: Iron*/Steel Size (mm) Number 110* NE NE daptor for UltraRib Pipe For connecting 150mm UltraRib pipe to all Range 450 Inspection hamber bases Size (mm) Number 150 6UR141$ Spares hamber ase to Shaft Seal 450mm diameter for use with 40NE300 at foot of shaft Material: EPM Size (mm) Number 450TW Osma/Wavin hambers PIM ustomer Services: Technical dvice:

44 Product etails Range 600 I Introduction escription 600mm diameter polypropylene inspection chamber for adoptable and non-adoptable applications. ompliant with Sewers for doption 7th edition [Sf7]. hoice of twelve bases for equal pipe connections. ompliance Range 600 chambers comply with the following standards and regulations S EN : 2009 a Sf7 Typical hamber etail Type 3: (Non-entry. Maximum depth from cover level to soffit of pipe: 3m) uilding Regulations Part H1: Shallow and/or eep For use directly with 150mm, 225mm and 300mm UltraRib system. 600mm diameter shaft may be cut to length to achieve required invert down to a maximum of 3 metres. pplications For above ground access and maintenance inspection of buried pipework down to 3 metres deep For loading applications: 125 (12.5 tonnes) * 400 (40 tonnes) * * With cover & frame supported by concrete plinth Key imensions Invert depth of base: 646mm [for 150mm system] 705mm [for 225mm and 300mm systems] External shaft diameter: 683mm Shaft length: 3m Maximum installation depth: 3m Key Features & enefits Fast, easy installation: no wet trades Lightweight: no lifting equipment required Reinforced base plate to withstand groundwater pressure Shaft can be cut to required length ll inlets and outlet sockets allow 7.5 movement in all directions Range 600 Inspection hamber assembly technical.design@wavin.co.uk Osma/Wavin hambers PIM 43

45 Product etails Range 600 I ases ll Range 600 bases are supplied with a base-to shaft sealing ring. When used in adoptable applications, maximum invert depth 3m. E /S Equal Inspection hamber ase 600mm dia. base straight channel and single inlet For use with 150mm, 225mm and 300mm UltraRib lso for connection to 150mm, 225mm and 300mm TwinWall using daptors 6TW145 (with 150 ase), 9TW145 (with 225 ase) or 12TW145 (with 300 ase) Size (mm) Number E NE300 a NE300 a NE300 a E /S Equal Inspection hamber ase 600mm dia. base incorporating bent 90 channel and single inlet For use with 150mm, 225mm and 300mm UltraRib lso for connection to 150mm, 225mm and 300mm TwinWall using daptors 6TW145 (with 150 ase), 9TW145 (with 225 ase) or 12TW145 (with 300 ase) Size (mm) Number E NE314 a NE314 a NE314 a E /S Equal Inspection hamber ase 600mm dia. base incorporating bent 30 channel and single inlet For use with 150mm, 225mm and 300mm UltraRib lso for connection to 150mm, 225mm and 300mm TwinWall using daptors 6TW145 (with 150 ase), 9TW145 (with 225 ase) or 12TW145 (with 300 ase) Size (mm) Number E NE315 a NE315 a NE315 a Osma/Wavin hambers PIM ustomer Services: Technical dvice:

46 E /S Equal Inspection hamber ase 600mm dia. base incorporating straight channel and three inlets including 2 x 90 equal branch inlets For use with 150mm, 225mm and 300mm UltraRib lso for connection to 150mm, 225mm and 300mm TwinWall using daptors 6TW145 (with 150 ase), 9TW145 (with 225 ase) or 12TW145 (with 300 ase) Size (mm) Number E NE316 a NE316 a NE316 a Shaft P/E Inspection hamber Shaft 600mm dia. plain-ended corrugated shaft Length: 3 metres For use with all Range 600 bases Size (mm) Number NE * * imension = effective height Restriction ccess ap Restriction ccess ap For use with 60NE300 shaft Restricts access to 350mm Supplied with one 600mm sealing ring Size (mm) Number NE technical.design@wavin.co.uk Osma/Wavin hambers PIM 45

47 Product etails Range 600 I ccessories onnector Kit For connecting 110/160mm plastic pipework to Range 600 Inspection hamber shaft Material: PV-U Nominal Part Size (mm) Number 110 NE NE960 hamber Shaft utter omponents For cutting 110/160mm connection holes to receive plastic pipework in Range 600 Inspection hamber shaft Material: Iron*/Steel Size (mm) Number 110* NE NE Spares hamber ase to Shaft Seal 600mm diameter for use with 60NE003 at foot of shaft Material: EPM Size (mm) Number 600TW Osma/Wavin hambers PIM ustomer Services: Technical dvice:

48 Installation Range 200 I Range 200 hamber and Shaft NOTE: The following is a summary of installation procedures following selection of a suitable Range 200 ase. The Range 200 inspection chamber may be installed in the same minimum trench width as required for standard 110mm or 160mm drainage pipework. NO extension of trench width is required. ll elements are lightweight: may be handled/installed by a single person. Excavation Take precautions against trench collapse: support trench sides deeper than 1.2m Preparation Prepare and compact 100mm regulating bed of granular material in trench bottom Positioning/connection Preparing shaft ut shaft to approx. Invert depth of hamber. REOMMENTION: leave extra 300mm depth to allow for possible final site changes lean inside of ase socket lean and lubricate entire spigot end of shaft to be inserted Position shaft at 45 angle into ase socket. Vertically push home manually or, if required, with mechanical assistance (if so, protect top of shaft) ackfill trench efore starting backfill, cover top of shaft to prevent ingress of dirt or grit NOTE: If finished ground level is not yet known, leave shaft proud of surface and keep open end covered until final completion. Figure 11: Typical installation detail: Range 200 Inspection hamber Type 4 over & Frame lass 125 loading riveway 150mm deep concrete collar Shuttering to external shaft 200mm dia Shaft Position ase on regulating bed. heck outlet is facing in the correct direction ompacted backfill as-dug or granular bedding material NOTE: On 24NE300/26NE300 Straight ases, a flow indication arrow is inscribed Ensure all inlets/outlet are free from dirt or grit If connecting to 150mm UltraRib, insert the appropriate adaptors into the required inlet/outlet as follows: 150mm UltraRib use daptor 6UR141 ends up to 45 may be used on inlet and outlet 100/110mm or 150/160 dia Pipe Granular bedding material ackfill Using same material as bedding, backfill around ase in 150mm layers up to underside of shaft socket. Ensure inside of ase is free of debris technical.design@wavin.co.uk Osma/Wavin hambers PIM 47

49 Installation Range 200 I 15 over and Frame 15 polypropylene cover and frames 20NE015 uses a dual fixing system for additional safety. The cover is pre-fixed to the frame using screws. REOMMENTION: use self-tapping screws [not supplied] to secure the frame to the shaft. Figure 12: Installation detail green areas (non-loaded) over & Frame lass 15 loading Garden 200mm dia Shaft ompacted backfill as-dug or granular bedding material For installation in areas not subject to loading, such as domestic gardens, no concrete plinth support is required (See Figure 12). For 15 applications subject to occasional/temporary vehicle loading up to 15kN (1.5 tonnes) such as domestic driveways, the frame should be supported by a concrete plinth (See Figure 13). Installation procedures: For green areas and pedestrian areas NOT* subject to vehicle loading (See Figure 12) EXMPLE: domestic gardens Trim shaft section at last stage of construction. Ensure unit is at correct height *For 15 applications subject to occasional vehicle loading up to 15kN (1.5 tonnes) (See Figure 13) Figure 13: Installation detail 15 areas subject to occasional vehicle loading up to 15kN (1.5 tonnes) For both non-load and occasional loading applications, as above Prepare polypropylene over and Frame [20NE015] for installation onto shaft Position the cover and frame spigot into the shaft section Fix frame to shaft using self-tapping screws over & Frame lass 15 loading Footways and landscaped areas 150mm deep concrete collar 200mm dia Shaft ompacted backfill as-dug or granular bedding material 100/110mm or 150/160 dia Pipe EXMPLE: domestic driveways Leave top 150mm of shaft clear of backfill Lay 150mm thick slab of pre-cast or in situ concrete around top of shaft chamber 48 Osma/Wavin hambers PIM ustomer Services: Technical dvice:

50 125 & 400 over and over & Frame lass 125 loading riveway uctile iron cover and frames uctile iron options are recommended 150mm for heavier deep loaded applications: concrete collar lass 125 with medium duty loading Shuttering capacity to of external 125kN (12.5 tonnes) where shaft the frame is supported by a concrete plinth. Suitable for applications such as 200mm dia Shaft car parks and service roads. Figure 14: Installation detail for 125 loading: paved areas with limited traffic load over & Frame lass 125 loading riveway 150mm deep concrete collar Shuttering to external shaft 200mm dia Shaft ompacted backfill as-dug or granular bedding material lass 400 classification with loading ompacted backfill as-dug capability or granular of up to 400kN (40 tonnes) bedding where material supported by a concrete plinth. Suitable for carriageways and roads subject to motor vehicle trafficking. Installation procedures: 100/110mm or 150/160 dia Pipe For 125 applications (See Figure 14) 100/110mm or 150/160 dia Pipe Granular bedding material EXMPLE: car parks and service roads Trim shaft section at last stage of construction. Ensure unit is at correct height Protect shaft from traffic loading by shuttering the outside of the shaft (See Figure 14) Lay 150mm thick slab of pre-cast or in situ concrete around top of shaft chamber with minimum opening 450mm x 450mm or 450mm diameter to ensure that any loads are distributed away from the shaft Position uctile Iron 125 over and Frame on top of slab (See Figure 14) Trafficked application (e.g. roadway) Follow Highway Specification for installation of a 400 over and Frame technical.design@wavin.co.uk Osma/Wavin hambers PIM 49

51 Installation Range 315 I Range 315 hamber and Shaft NOTE: The following is a summary of installation procedures following selection of a suitable ase for the required number of inlets. The Range 315 inspection chamber may be installed in the same minimum trench width as required for standard 110mm or 160mm drainage pipework. NO extension of trench width is required. ll elements are lightweight: may be handled/installed by a single person. Excavation Take precautions against trench collapse: support trench sides deeper than 1.2m Preparation Prepare and compact 100mm regulating bed of granular material in trench bottom Positioning/connection Position ase on regulating bed. heck outlet is facing in the correct direction NOTE: On 34NE300/36NE300 Straight ases, a flow indication arrow is inscribed ackfill Using same material as bedding, backfill around ase in 150mm layers up to underside of shaft socket. Ensure inside of ase is free of debris. Preparing shaft ut corrugated shaft to approx. Invert depth of hamber. REOMMENTION: leave extra 300mm depth to allow for possible final site changes Locate sealing ring between 2nd and 3rd ribs from shaft bottom. Ensure ring is seated correctly/not twisted lean inside of ase socket and lubricate this entire area. Position shaft at 45 angle into ase socket. Vertically push home manually or, if required, with mechanical assistance (if so, protect top of shaft) ackfill trench efore starting backfill, cover top of shaft with cap provided NOTE: If finished ground level is not yet known, leave shaft proud of surface and keep open end covered until final completion. Figure 15: Typical installation detail: Range 315 Inspection hamber. Type 4 over & Frame lass 125 loading riveway lass engineering bricks set in class 1 mortar 150mm deep concrete collar Shuttering to external ribs If connecting to 150mm UltraRib, insert the appropriate adaptors into the required inlet/outlet as follows: 150mm UltraRib use daptor 6UR141 Use standard jointing sequence to connect 100/110mm or 150/160mm pipes to inlets/outlet. Push lank-off Plugs into any unused inlets 315mm dia Shaft ompacted backfill as-dug or granular bedding material NOTE: The main through channel MUST be used. ends up to 45 may be used on any inlet or outlet. 100/110mm or 150/160 dia Pipe Granular bedding material 50 Osma/Wavin hambers PIM ustomer Services: Technical dvice:

52 15 over and Frame 15 polypropylene cover and frames Figure 16: Installation detail green areas (non-loaded) over & Frame lass 15 loading Garden 30NE015 uses a dual fixing system for additional safety. The cover is pre-fixed to the frame using screws. REOMMENTION: use self-tapping screws [not supplied] to secure the frame to the shaft. 315mm dia Shaft ompacted backfill as-dug or granular bedding material For installation in areas not subject to loading, such as domestic gardens, no concrete plinth support is required. (See Figure 16). For 15 applications subject to occasional/temporary vehicle loading up to 15kN (1.5 tonnes) such as domestic driveways, the frame should be supported by a concrete plinth. (See Figure 17). Installation procedures: For green areas and pedestrian areas NOT* subject to vehicle loading (See Figure 16) Figure 17: Installation detail 15 areas subject to occasional vehicle loading up to 15kN (1.5 tonnes) For all 15 applications over & Frame lass 15 loading Footways and landscaped areas 150mm deep concrete collar 315mm dia Shaft ompacted backfill as-dug or granular bedding material 110/160mm dia Pipe EXMPLE: domestic gardens Trim shaft section at last stage of construction. Ensure unit is at correct height *For 15 applications subject to occasional vehicle loading up to 15kN (1.5 tonnes) (See Figure 17) EXMPLE: domestic driveways Leave top 150mm of shaft clear of backfill Lay 150mm thick slab of pre-cast or in situ concrete around top of shaft chamber lean outside of shaft section between first and second rib Locate sealing ring ensuring it is seated correctly/not twisted Prepare polypropylene 15 over and Frame [30NE015] for installation onto shaft: clean inside of frame socket area apply lubricant to entire surface area Position the cover and frame socket over the shaft section and push home Screw frame to shaft using selftapping screws [not provided] Granular bedding material 110/160mm dia Pipe Granular bedding material technical.design@wavin.co.uk Osma/Wavin hambers PIM 51

53 Installation Range 315 I 125 & 400 over and Frame uctile iron cover and frames uctile iron options are recommended for heavier loaded applications: lass 125 with medium duty loading capacity of 125kN (12.5 tonnes) where the frame is supported by a concrete plinth. Suitable for applications such as car parks and service roads. lass 400 classification with loading capability of up to 400kN (40 tonnes) where supported by a concrete plinth. Suitable for carriageways and roads subject to motor vehicle trafficking. Figure 18: Installation detail for 125 loading: paved areas with limited traffic load over & Frame lass 125 loading riveway lass engineering bricks set in class 1 mortar 150mm deep concrete collar Shuttering to external ribs 315mm dia Shaft ompacted backfill as-dug or granular bedding material Installation procedures: For 125 applications (See Figure 18) EXMPLE: car parks and service roads Trim shaft section at last stage of construction. Ensure unit is at correct height Protect shaft from traffic loading by shuttering its external ribs (See Figure 18) Lay 150mm thick slab of pre-cast or in situ concrete around top of shaft chamber with minimum opening 450mm x 450mm or 450mm diameter to ensure that any loads are distributed away from the shaft Position uctile Iron 125 over and Frame on top of slab. (See Figure 18) 110/160mm dia Pipe Granular bedding material Trafficked application (e.g. roadway) Follow Highway Specification for installation of a 400 over and Frame 52 Osma/Wavin hambers PIM ustomer Services: Technical dvice:

54 Installation Range 450 I Range 450 hamber and Shaft NOTE: The following is a summary of installation procedures following selection of a suitable Range 450 ase for the required number of inlets. Excavation Take precautions against trench collapse: support trench sides deeper than 1.2m Preparation Prepare and compact 100mm regulating bed of granular material in trench bottom Positioning/connection Preparing shaft ut corrugated shaft to approx. Invert depth of hamber. REOMMENTION: leave extra 300mm depth to allow for possible final site changes Locate sealing ring between 2nd and 3rd ribs from shaft bottom. Ensure ring is seated correctly/not twisted lean inside of ase socket and lubricate this entire area Position shaft at 45 angle into ase socket. Vertically push home manually or, if required, with mechanical assistance (if so, protect top of shaft) ackfill trench efore starting backfill, cover top of shaft to prevent ingress of dirt or grit Trim shaft/fit restriction access cap Trim shaft to required height using finetoothed saw NOTE: If finished ground level is not yet known, leave shaft proud of surface and keep open end covered until final completion. When shaft trimmed to final height, locate sealing ring between 2nd and 3rd ribs from shaft top. Ensure ring is seated correctly/not twisted Lubricate inside of the 450 to 350mm restrictor cap, position over top of shaft, and push fully home Position ase on regulating bed. heck outlet is facing in the correct direction: i.e. with side inlets swept to follow water flow If connecting to 150mm UltraRib, insert the appropriate adaptors into the required inlet/outlet as follows: 150mm UltraRib use daptor 6UR141 Use standard jointing sequence to connect 100/110mm or 150/160mm pipes to inlets/outlet. Push lank-off Plugs into any unused inlets Figure 19: Typical installation detail: Range 450 Inspection hamber. Type 4 over & Frame lass 125 loading riveway lass engineering bricks set in class 1 mortar 150mm deep concrete collar Shuttering to external cap Restrictor cap 450mm dia to 350mm dia NOTE: The main through channel MUST be used. ends up to 45 may be used on any inlet or outlet. 450mm dia Shaft ackfill Using same material as bedding, backfill around ase in 150mm layers up to underside of shaft socket. Ensure inside of ase is free of debris ompacted backfill as-dug or granular bedding material 100/110mm or 150/160 dia Pipe Granular bedding material technical.design@wavin.co.uk Osma/Wavin hambers PIM 53

55 Installation Range 450 I Installation procedures: For 15 applications in domestic garden areas and/or subject to occasional vehicle loading up to 15kN (1.5 tonnes) (See Figure 20) EXMPLE: domestic driveways Leave top 150mm of shaft clear of backfill Lay 150mm thick slab of pre-cast or in situ concrete around top of shaft chamber Prepare 15 over and Frame for installation in accordance with manufacturer s instructions Position the cover and frame socket on top of slab and fix in accordance with manufacturer s instructions 125 & 400 over and Frame Installation procedures: For 125 Paved areas with limited traffic load Trim shaft section at last stage of construction. Ensure unit is at correct height Protect shaft from traffic loading by shuttering its external ribs (See Figure 21) Lay 150mm thick slab of pre-cast or in situ concrete around top of shaft chamber with minimum opening 750mm x 750mm or 750mm diameter to ensure that any loads are distributed away from the shaft Position uctile Iron 125 over and Frame on top of slab. (See Figure 21) Trafficked application (e.g. roadway) Follow Highway Specification for installation of a 400 over and Frame Figure 20: Installation detail 15 domestic gardens and/or areas subject to occasional vehicle loading up to 15kN (1.5 tonnes) over & Frame lass 15 loading ar Surface 150mm deep concrete collar Shuttering to external cap Restrictor cap 450mm dia to 350mm dia 450mm dia Shaft ompacted backfill as-dug or granular bedding material Figure 21: Installation detail for 125 loading: paved areas with limited traffic load over & Frame lass 125 loading riveway lass engineering bricks set in class 1 mortar 150mm deep concrete collar 150mm, Shuttering 225mm to external or cap 300mm dia Pipe Restrictor cap 450mm dia to 350mm dia Granular bedding material 450mm dia Shaft ompacted backfill as-dug or granular bedding material 150mm, 225mm or 300mm dia Pipe Granular bedding material 54 Osma/Wavin hambers PIM ustomer Services: Technical dvice:

56 Installation Range 600 I Range 600 hamber and Shaft NOTE: The following is a summary of installation procedures following selection of a suitable Range 600 ase for the required number of inlets. Excavation Take precautions against trench collapse: support trench sides deeper than 1.2m Preparation Prepare and compact 100mm regulating bed of granular material in trench bottom Positioning/connection Preparing shaft ut corrugated shaft to approx. Invert depth of hamber. REOMMENTION: leave extra 300mm depth to allow for possible final site changes Locate sealing ring between 2nd and 3rd ribs from shaft bottom. Ensure ring is seated correctly/not twisted lean inside of ase socket and lubricate this entire area Position shaft at 45 angle into ase socket. Vertically push home manually or, if required, with mechanical assistance (if so, protect top of shaft) ackfill trench efore starting backfill, cover top of shaft to prevent ingress of dirt or grit Trim shaft/fit restriction access cap Trim shaft to required height using finetoothed saw NOTE: If finished ground level is not yet known, leave shaft proud of surface and keep open end covered until final completion. When shaft trimmed to final height, locate sealing ring between 2nd and 3rd ribs from shaft top. Ensure ring is seated correctly/not twisted Lubricate inside of the 600 to 350mm restrictor cap, position over top of shaft, and push fully home Position ase on regulating bed. heck outlet is facing in the correct direction: i.e. with side inlets swept to follow water flow Ensure all inlets/outlet are free from dirt or grit Use standard jointing sequence to connect 150mm, 225mm or 300mm UltraRib pipes to inlets/outlet For connection of TwinWall pipes in these sizes, use daptors 6TW145, 9TW145 or 12TW145. Figure 22: Typical installation detail: Range 600 Inspection hamber. Type 3 over & Frame lass 125 loading riveway lass engineering bricks set in class 1 mortar 150mm deep concrete collar Shuttering to external cap Restrictor cap 600mm dia to 350mm dia NOTE: The main through channel MUST be used. ends up to 45 may be used on any inlet or outlet. ackfill 600mm dia Shaft Using same material as bedding, backfill around ase in 150mm layers up to underside of shaft socket. Ensure inside of ase is free of debris ompacted backfill as-dug or granular bedding material 150mm, 225mm or 300mm dia Pipe Granular bedding material technical.design@wavin.co.uk Osma/Wavin hambers PIM 55

57 Installation Range 600 I Installation procedures: For 15 applications in domestic garden areas and/or subject to occasional vehicle loading up to 15kN (1.5 tonnes) (See Figure 23) EXMPLE: domestic driveways Leave top 150mm of shaft clear of backfill Lay 150mm thick slab of pre-cast or in situ concrete around top of shaft chamber Prepare 15 over and Frame for installation in accordance with manufacturer s instructions Position the cover and frame socket on top of slab and fix in accordance with manufacturer s instructions 125 & 400 over and Frame Installation procedures: For 125 Paved areas with limited traffic load Trim shaft section at last stage of construction. Ensure unit is at correct height Protect shaft from traffic loading by shuttering its external ribs (See Figure 24) Lay 150mm thick slab of pre-cast or in situ concrete around top of shaft chamber with minimum opening 750mm x 750mm or 750mm diameter to ensure that any loads are distributed away from the shaft Position uctile Iron 125 over and Frame on top of slab. (See Figure 24) Trafficked application (e.g. roadway) Follow Highway Specification for installation of a 400 over and Frame Figure 23: Installation detail 15 domestic gardens and/or areas subject to occasional vehicle loading up to 15kN (1.5 tonnes) over & Frame lass 125 loading ar Surface 150mm deep concrete collar Shuttering to external cap Restrictor cap 600mm dia to 350mm dia 600mm dia Shaft ompacted backfill as-dug or granular bedding material Figure 24: Installation detail for 125 loading: paved areas with limited traffic load over & Frame lass 125 loading riveway lass engineering bricks set in class 1 mortar 150mm deep concrete collar 150mm, Shuttering 225mm to external or cap 300mm dia Pipe Restrictor cap 600mm dia to 350mm dia Granular bedding material 600mm dia Shaft ompacted backfill as-dug or granular bedding material 150mm, 225mm or 300mm dia Pipe Granular bedding material 56 Osma/Wavin hambers PIM ustomer Services: Technical dvice:

58 Installation Typical ackdrop onnection ackdrop onnections for Ranges 315, 450 and 600 Installation of backdrop connections chamber which has substantially different invert levels will require backdrop connection of one or more drains. This operation can be done externally on site (See Figure 25). Use a combination of ackdrop Kit [NE950 or NE960], with associated 100/110mm or 150/160mm fittings, for in situ connection to a shaft, as follows: rill required opening into corrugated shaft section at appropriate place lean and remove any swarf from the opening Install the special 110mm or 160mm seal into the opening Fully lubricate around the entire internal surface of the seal Insert specially designed in-situ socket connector into the seal opening Lubricate the outside surface of the spigot pipe to be connected and insert into the socket connector Make remaining connections in the same way as for standard jointing of 110mm or 160mm pipes and or fittings Figure 25: Typical installation detail typical backdrop situation over & Frame lass 125 loading riveway lass engineering bricks set in class 1 mortar 150mm deep concrete collar Shuttering to external cap Restrictor cap 450mm dia to 350mm dia 450mm dia Shaft ompacted backfill as-dug or granular bedding material 100/110mm or 150/160mm dia Pipe Granular bedding material technical.design@wavin.co.uk Osma/Wavin hambers PIM 57

59 Testing and Maintenace Osma/Wavin hambers Testing ll testing of these non-man entry chambers and connecting pipework must be undertaken at ground level. For guidance, please use the following: ir Testing using remote test bags: equipment required 3 x 1 metre x 8mm Steel rainage Rods 50mm ouble Worm Screw for use with Steel rainage Rods PV sealing bags fitted with Schrader Valve and 6 metre hose Steel drain plug with testing point icycle Pump Tyre pressure gauge to ensure correct inflation pressure of the test bags ir Testing procedure 1. ssemble drain rods to 3 metres in length with double worm attachment on end. 2. Remove as much air as possible from the PV Sealing ag. Method: hold valve open and squeeze bag flat. Tip: folding the bag in half to make it as small as possible will make it easier to locate. 3. Twist neck of PV Sealing ag into double worm attachment until it has firm grip on bag. 4. Ensure valve end of hose is secure with no danger of falling down the chamber. 5. Hold drain rods and hose from the PV Sealing ag together. Start to lower the test bag into the base. 9. If required, remove rods by twisting them in an anti-clockwise direction to release the double worm. heck the valve end of hose is safely positioned. 10. Place a similar sealing bag or a steel drain plug at the other end of the pipe length to be tested. (This could be another chamber or a terminal access point.) oth bag and steel drain plug must include a suitable testing point. 11. ttach a manometer. arry out required air test method. 12. Remove sealing bag. Method: twist double worm attachment around the hose at ground level. Lower it down the hose, guiding the rods to the bottom of the chamber and once again grip the bag. NOTE: No requirement to grip bag tightly. This is simply to aid its removal. Release as much air as possible from bag. Then slide bag back out the pipe with the rods. When this is done, lift/remove all test equipment out of the chamber. Maintenance s with all Osma/Wavin hambers, the smooth interior bore of chamber channels and associated pipe systems will aid the flow of water and waste through the system. ecause man-entry of Osma/Wavin chambers is not possible, maintenance work such as Rodding, Jetting and TV inspection must be undertaken at ground level. lways follow the Health & Safety and Operational procedures of equipment suppliers. Tip: Keep hose tight while lowering bag. This helps to keep bag in place. 6. When bag is in chamber base, position it into the channel of the run to be tested. 7. y using the channel as a guide, slide test bag into the mouth of the pipe, and as far as possible into the pipe. Method: use rods to push bag into position. 8. Leave rods attached (this ensures bag is held in position). Start to pump the bag up using a bicycle pump. NOTE: When inflating the test bags, follow manufacturer s instructions to ensure pressure is not exceeded. Use tyre pressure valve to monitor bag pressure. 58 Osma/Wavin hambers PIM ustomer Services: Technical dvice:

60 iscover our broad portfolio at Water management Plumbing and heating Waste water drainage Water and gas distribution able ducting Wavin Limited Registered Office Edlington Lane oncaster N12 1Y Tel Wavin Limited Wavin operates a programme of continuous product development, and therefore reserves the right to modify or amend the specification of their products without notice. ll information in this publication is given in good faith, and believed to be correct at the time of going to press. However, no responsibility can be accepted for any errors, omissions or incorrect assumptions. Users should satisfy themselves that products are suitable for the purpose and application intended. For further product information visit: wavin.co.uk OWI001 June 2015