* technical applications of rubbers and platics

Transcription

1 * technical applications of rubbers and platics Applications Techniques des Caoutchoucs et des Plastiques* 1 Rue des Gaillards, ZAC des Doucettes, Garges-lès-Gonesse, France Tél : Fax : Site web : atcp.net

2 Laminated elastomeric bearings, ATCPAD ATCP designs and manufactures laminated elastomeric bearings, ATCPAD, as per following requirements: EN 1337 BS 5400 AASHTO LRDF All bearings described in this brochure are covered by the CE marking when EN 1337 is required. A laminated elastomeric bearing is a rubber bloc vulcanized with internal reinforcing steel plates. It looks like a stack of rubber layers and steel plates of constant thickness. To protect the steel plate, the stack is laterally covered by a rubber belt and a thin rubber sheet called cover at upper and lower faces. upper rubber cover rubber belt internal steel plate rubber layer lower rubber cover For buildings, elastomeric bearings are usually manufactured without reinforcing steel plates and look like rubber strips. Such bearings are not allowed for engineering structures like bridges. The bearing is a linking element between the structure and its support. For example, it can be found between the piers and the deck of a bridge. It allows: the transfert of vertical and horizontal loads, the rotation is many directions and the horizontal displacements by rubber deformation as per following technical principles: initial bearing bearing under compression due to the vertical load bearing under rotation bearing under distorsion due to horizontal loads and displacements

3 Laminated elastomeric bearings, ATCPAD ATCP proposes two types of rubber: Natural (NR) and Neoprene (CR) as per following physical characteristics: G modulus hardness tensile strength mouled test piece test piece from bearing elongation at break: mouled test piece test piece from bearing NR CR 0.9 MPa +/ MPa 0.9 MPa +/ MPa à 23 C +/-2 C à 23 C +/-2 C 60 +/-5 shore A 60 +/-5 shore A à 23 C +/-2 C à 23 C +/-2 C 16 MPa 14 MPa 16 MPa 14 MPa 425% 425% 375% 375% tear resistance 5 kn/m 7 kn/m compression set at 24h ; 70 C accelerated ageing: hardness tensile strength elongation at break 30% 15% -5 / +10 Shore A (7 d, 70 C) +/-5 Shore A (3 d, 100 C) +/-15% (7 d, 70 C) +/-15% (3 d, 100 C) +/-25% (7 d, 70 C) +/-25% (3 d, 100 C) ozone resistance elongation 30% 96h 40 C +/- 2 C no cracks at 25 pphm no cracks at 100 pphm Following is a table of a qualitative comparison of the both rubber types: resistance to: break tear abrasion successive flexions compression NR CR ageing: in the air under the sun at ozone exposition / durability to: heat fire cold +/ electrical property isolating power /- To get the advantages of both rubber types (resistance of NR, durability and ageing of CR) ATCP can manufacture laminated elastomeric bearings with NR inside (internal rubber layers) and CR outside (rubber belt). Internal and external steel plates are manufactured in S235 as per EN requirement.

4 Laminated elastomeric bearings, ATCPAD Norms decrib different types of laminated elastomeric bearings. As per EN , bearings are named as following: standard bearings for every kind of structure: - type B: laminated bearing fully covered with rubber and comprising at least two reinforcing steel plates - type C: laminated bearing with one or two outer thick steel plate. Outer plates may be checkered and allow fixings to the structure and/or to the support standard bearings for buildings only (not allowed for engineering structures): - type A: laminated bearing fully covered with rubber and comprising only one reinforcing steel plate - type F: plain elastomeric bearing which may be manufactured in strip shape sliding bearings for every kind of structure: - type D: type B bearing with a PTFE sheet, with or without dimples, bonded to the rubber during the vulcanization. In case of PTFE damage, the entire bearing shall be replaced PTFE sheet without dimlples PTFE with dimples - type E: type C bearing with a dimpled PTFE sheet recessed in outer steel plate. In case of PTFE damage, the PTFE sheet may be replaced alone

5 Laminated elastomeric bearings, ATCPAD ATCP design and provide accessories like anchor systems of type C bearings. ATCP proposes 4 types of fixings. If required, the client can ask for a mixed fixing solution. Type C1 : the bearing is manufactured with checkered external steel plates. These plates are directly in contact with the grout to increase the sliping resistance which is bigger than the one obtained by friction only. This technology is very cheap and let take low horizontal loads. checkered steel plate Type C2 : the bearing is installed on anchor plates. Lateral stoppers are screwed or welded on the anchor plates all around the bearing to avoid its sliping. This technology let take high horizontal loads. To remove more easily the bearing, we advise to screw at least one stopper in order to limit the jacking height. stud welded to the anchor plate anchor plate welded or screwed stopper Type C3 : the bearing is manufactured with boundless external steel plates. These ones are screwed to embedded anchor dowels for a concrete structure or directly to the steel structure or to embedded anchor plates. This technology is cheap and let take high horizontal loads. The bearing can be easily removed because the jacking height is low. dowel boundless external steel plate screw Type C4 : the bearing and its anchor plates are linked with shear discs which is reccessed in the anchor plates and the bearing external plates. This technology lets take very high horizontal loads for a limited space. To remove the bearing the jacking height may be high. stud welded to the anchor plate anchor plate shear disc

6 # Type B EN (1) Type B Setra (3) Type C EN (2) Type C Setra (4) width or diameter of the bearing length of the bearing thickness of internal rubber layers thickness of reinforcing steel plates number of internal rubber layers thickness of outer steel plates total tickness of rubber under distorsion a 0 /Ø b 0 t i t s n (5) t so T q (6) permissive vertical load F z permissive horizontal load F xy permissive displacement permissive rotation v xy alpha mm mm mm mm u mm mm kn kn nn rad 1 100x150x30/16 ; 2(8+3) 100x150x22/16 ; 1(8+3) ; 2x4 100x150x49/16 ; 2(8+3)+8 ; 2x15 100x150x52/16 ; 1(8+3) ; 2x4 ; 2x x150x41/24 ; 3(8+3) 100x150x33/24 ; 2(8+3) ; 2x4 100x150x60/24 ; 3(8+3)+8 ; 2x15 100x150x63/24 ; 2(8+3) ; 2x4 ; 2x x200x30/16 ; 2(8+3) 100x200x22/16 ; 1(8+3) ; 2x4 100x200x49/16 ; 2(8+3)+8 ; 2x15 100x200x52/16 ; 1(8+3) ; 2x4 ; 2x x200x41/24 ; 3(8+3) 100x200x33/24 ; 2(8+3) ; 2x4 100x200x60/24 ; 3(8+3)+8 ; 2x15 100x200x63/24 ; 2(8+3) ; 2x4 ; 2x x200x30/16 ; 2(8+3) 150x200x22/16 ; 1(8+3) ; 2x4 150x200x49/16 ; 2(8+3)+8 ; 2x15 150x200x52/16 ; 1(8+3) ; 2x4 ; 2x x200x41/24 ; 3(8+3) 150x200x33/24 ; 2(8+3) ; 2x4 150x200x60/24 ; 3(8+3)+8 ; 2x15 150x200x63/24 ; 2(8+3) ; 2x4 ; 2x x200x52/32 ; 4(8+3) 150x200x44/32 ; 3(8+3) ; 2x4 150x200x71/32 ; 4(8+3)+8 ; 2x15 150x200x74/32 ; 3(8+3) ; 2x4 ; 2x Ø200x30/16 ; 2(8+3) Ø200x22/16 ; 1(8+3) ; 2x4 Ø200x49/16 ; 2(8+3)+8 ; 2x15 Ø200x52/16 ; 1(8+3) ; 2x4 ; 2x Ø200x41/24 ; 3(8+3) Ø200x33/24 ; 2(8+3) ; 2x4 Ø200x60/24 ; 3(8+3)+8 ; 2x15 Ø200x63/24 ; 2(8+3) ; 2x4 ; 2x Ø200x52/32 ; 4(8+3) Ø200x44/32 ; 3(8+3) ; 2x4 Ø200x71/32 ; 4(8+3)+8 ; 2x15 Ø200x74/32 ; 3(8+3) ; 2x4 ; 2x x250x30/16 ; 2(8+3) 150x250x22/16 ; 1(8+3) ; 2x4 150x250x49/16 ; 2(8+3)+8 ; 2x15 150x250x52/16 ; 1(8+3) ; 2x4 ; 2x x250x41/24 ; 3(8+3) 150x250x33/24 ; 2(8+3) ; 2x4 150x250x60/24 ; 3(8+3)+8 ; 2x15 150x250x63/24 ; 2(8+3) ; 2x4 ; 2x x250x52/32 ; 4(8+3) 150x250x44/32 ; 3(8+3) ; 2x4 150x250x71/32 ; 4(8+3)+8 ; 2x15 150x250x74/32 ; 3(8+3) ; 2x4 ; 2x x300x30/16 ; 2(8+3) 150x300x22/16 ; 1(8+3) ; 2x4 150x300x49/16 ; 2(8+3)+8 ; 2x15 150x300x52/16 ; 1(8+3) ; 2x4 ; 2x x300x41/24 ; 3(8+3) 150x300x33/24 ; 2(8+3) ; 2x4 150x300x60/24 ; 3(8+3)+8 ; 2x15 150x300x63/24 ; 2(8+3) ; 2x4 ; 2x x300x52/32 ; 4(8+3) 150x300x44/32 ; 3(8+3) ; 2x4 150x300x71/32 ; 4(8+3)+8 ; 2x15 150x300x74/32 ; 3(8+3) ; 2x4 ; 2x Ø250x30/16 ; 2(8+3) Ø250x22/16 ; 1(8+3) ; 2x4 Ø250x49/16 ; 2(8+3)+8 ; 2x15 Ø250x52/16 ; 1(8+3) ; 2x4 ; 2x Ø250x41/24 ; 3(8+3) Ø250x33/24 ; 2(8+3) ; 2x4 Ø250x60/24 ; 3(8+3)+8 ; 2x15 Ø250x63/24 ; 2(8+3) ; 2x4 ; 2x Ø250x52/32 ; 4(8+3) Ø250x44/32 ; 3(8+3) ; 2x4 Ø250x71/32 ; 4(8+3)+8 ; 2x15 Ø250x74/32 ; 3(8+3) ; 2x4 ; 2x x250x41/24 ; 3(8+3) 200x250x33/24 ; 2(8+3) ; 2x4 200x250x60/24 ; 3(8+3)+8 ; 2x15 200x250x63/24 ; 2(8+3) ; 2x4 ; 2x x250x52/32 ; 4(8+3) 200x250x44/32 ; 3(8+3) ; 2x4 200x250x71/32 ; 4(8+3)+8 ; 2x15 200x250x74/32 ; 3(8+3) ; 2x4 ; 2x x250x63/40 ; 5(8+3) 200x250x55/40 ; 4(8+3) ; 2x4 200x250x82/40 ; 5(8+3)+8 ; 2x15 200x250x85/40 ; 4(8+3) ; 2x4 ; 2x x250x74/48 ; 6(8+3) 200x250x66/48 ; 5(8+3) ; 2x4 200x250x93/48 ; 6(8+3)+8 ; 2x15 200x250x96/48 ; 5(8+3) ; 2x4 ; 2x x300x41/24 ; 3(8+3) 200x300x33/24 ; 2(8+3) ; 2x4 200x300x60/24 ; 3(8+3)+8 ; 2x15 200x300x63/24 ; 2(8+3) ; 2x4 ; 2x x300x52/32 ; 4(8+3) 200x300x44/32 ; 3(8+3) ; 2x4 200x300x71/32 ; 4(8+3)+8 ; 2x15 200x300x74/32 ; 3(8+3) ; 2x4 ; 2x x300x63/40 ; 5(8+3) 200x300x55/40 ; 4(8+3) ; 2x4 200x300x82/40 ; 5(8+3)+8 ; 2x15 200x300x85/40 ; 4(8+3) ; 2x4 ; 2x x300x74/48 ; 6(8+3) 200x300x66/48 ; 5(8+3) ; 2x4 200x300x93/48 ; 6(8+3)+8 ; 2x15 200x300x96/48 ; 5(8+3) ; 2x4 ; 2x x350x41/24 ; 3(8+3) 200x350x33/24 ; 2(8+3) ; 2x4 200x350x60/24 ; 3(8+3)+8 ; 2x15 200x350x63/24 ; 2(8+3) ; 2x4 ; 2x x350x52/32 ; 4(8+3) 200x350x44/32 ; 3(8+3) ; 2x4 200x350x71/32 ; 4(8+3)+8 ; 2x15 200x350x74/32 ; 3(8+3) ; 2x4 ; 2x x350x63/40 ; 5(8+3) 200x350x55/40 ; 4(8+3) ; 2x4 200x350x82/40 ; 5(8+3)+8 ; 2x15 200x350x85/40 ; 4(8+3) ; 2x4 ; 2x x350x74/48 ; 6(8+3) 200x350x66/48 ; 5(8+3) ; 2x4 200x350x93/48 ; 6(8+3)+8 ; 2x15 200x350x96/48 ; 5(8+3) ; 2x4 ; 2x Ø300x41/24 ; 3(8+3) Ø300x33/24 ; 2(8+3) ; 2x4 Ø300x60/24 ; 3(8+3)+8 ; 2x15 Ø300x63/24 ; 2(8+3) ; 2x4 ; 2x Ø300x52/32 ; 4(8+3) Ø300x44/32 ; 3(8+3) ; 2x4 Ø300x71/32 ; 4(8+3)+8 ; 2x15 Ø300x74/32 ; 3(8+3) ; 2x4 ; 2x Ø300x63/40 ; 5(8+3) Ø300x55/40 ; 4(8+3) ; 2x4 Ø300x82/40 ; 5(8+3)+8 ; 2x15 Ø300x85/40 ; 4(8+3) ; 2x4 ; 2x Ø300x74/48 ; 6(8+3) Ø300x66/48 ; 5(8+3) ; 2x4 Ø300x93/48 ; 6(8+3)+8 ; 2x15 Ø300x96/48 ; 5(8+3) ; 2x4 ; 2x x400x41/24 ; 3(8+3) 200x400x33/24 ; 2(8+3) ; 2x4 200x400x60/24 ; 3(8+3)+8 ; 2x15 200x400x63/24 ; 2(8+3) ; 2x4 ; 2x x400x52/32 ; 4(8+3) 200x400x44/32 ; 3(8+3) ; 2x4 200x400x71/32 ; 4(8+3)+8 ; 2x15 200x400x74/32 ; 3(8+3) ; 2x4 ; 2x Table of normalized dimensions of type B and C bearings as per EN with allowed capacities x400x63/40 ; 5(8+3) 200x400x55/40 ; 4(8+3) ; 2x4 200x400x82/40 ; 5(8+3)+8 ; 2x15 200x400x85/40 ; 4(8+3) ; 2x4 ; 2x x400x74/48 ; 6(8+3) 200x400x66/48 ; 5(8+3) ; 2x4 200x400x93/48 ; 6(8+3)+8 ; 2x15 200x400x96/48 ; 5(8+3) ; 2x4 ; 2x

7 # Type B EN (1) Type B Setra (3) Type C EN (2) Type C Setra (4) a 0 /Ø b 0 t i t s n (5) t so (6) T q F z F xy v xy alpha mm mm mm mm u mm mm kn kn nn rad x300x41/24 ; 3(8+3) 250x300x33/24 ; 2(8+3) ; 2x4 250x300x60/24 ; 3(8+3)+8 ; 2x15 250x300x63/24 ; 2(8+3) ; 2x4 ; 2x x300x52/32 ; 4(8+3) 250x300x44/32 ; 3(8+3) ; 2x4 250x300x71/32 ; 4(8+3)+8 ; 2x15 250x300x74/32 ; 3(8+3) ; 2x4 ; 2x x300x63/40 ; 5(8+3) 250x300x55/40 ; 4(8+3) ; 2x4 250x300x82/40 ; 5(8+3)+8 ; 2x15 250x300x85/40 ; 4(8+3) ; 2x4 ; 2x x300x74/48 ; 6(8+3) 250x300x66/48 ; 5(8+3) ; 2x4 250x300x93/48 ; 6(8+3)+8 ; 2x15 250x300x96/48 ; 5(8+3) ; 2x4 ; 2x x300x85/56 ; 7(8+3) 250x300x77/56 ; 6(8+3) ; 2x4 250x300x104/56 ; 7(8+3)+8 ; 2x15 250x300x107/56 ; 6(8+3) ; 2x4 ; 2x x400x41/24 ; 3(8+3) 250x400x33/24 ; 2(8+3) ; 2x4 250x400x60/24 ; 3(8+3)+8 ; 2x15 250x400x63/24 ; 2(8+3) ; 2x4 ; 2x x400x52/32 ; 4(8+3) 250x400x44/32 ; 3(8+3) ; 2x4 250x400x71/32 ; 4(8+3)+8 ; 2x15 250x400x74/32 ; 3(8+3) ; 2x4 ; 2x x400x63/40 ; 5(8+3) 250x400x55/40 ; 4(8+3) ; 2x4 250x400x82/40 ; 5(8+3)+8 ; 2x15 250x400x85/40 ; 4(8+3) ; 2x4 ; 2x x400x74/48 ; 6(8+3) 250x400x66/48 ; 5(8+3) ; 2x4 250x400x93/48 ; 6(8+3)+8 ; 2x15 250x400x96/48 ; 5(8+3) ; 2x4 ; 2x x400x85/56 ; 7(8+3) 250x400x77/56 ; 6(8+3) ; 2x4 250x400x104/56 ; 7(8+3)+8 ; 2x15 250x400x107/56 ; 6(8+3) ; 2x4 ; 2x x400x57/36 ; 3(12+4) 300x400x48/36 ; 2(12+4) ; 2x6 300x400x80/36 ; 3(12+4)+12 ; 2x18 300x400x84/36 ; 2(12+4) ; 2x6 ; 2x x400x73/48 ; 4(12+4) 300x400x64/48 ; 3(12+4) ; 2x6 300x400x96/48 ; 4(12+4)+12 ; 2x18 300x400x100/48 ; 3(12+4) ; 2x6 ; 2x x400x89/60 ; 5(12+4) 300x400x80/60 ; 4(12+4) ; 2x6 300x400x112/60 ; 5(12+4)+12 ; 2x18 300x400x116/60 ; 4(12+4) ; 2x6 ; 2x x400x105/72 ; 6(12+4) 300x400x96/72 ; 5(12+4) ; 2x6 300x400x128/72 ; 6(12+4)+12 ; 2x18 300x400x132/72 ; 5(12+4) ; 2x6 ; 2x Ø400x57/36 ; 3(12+4) Ø400x48/36 ; 2(12+4) ; 2x6 Ø400x80/36 ; 3(12+4)+12 ; 2x18 Ø400x84/36 ; 2(12+4) ; 2x6 ; 2x Ø400x73/48 ; 4(12+4) Ø400x64/48 ; 3(12+4) ; 2x6 Ø400x96/48 ; 4(12+4)+12 ; 2x18 Ø400x100/48 ; 3(12+4) ; 2x6 ; 2x Ø400x89/60 ; 5(12+4) Ø400x80/60 ; 4(12+4) ; 2x6 Ø400x112/60 ; 5(12+4)+12 ; 2x18 Ø400x116/60 ; 4(12+4) ; 2x6 ; 2x Ø400x105/72 ; 6(12+4) Ø400x96/72 ; 5(12+4) ; 2x6 Ø400x128/72 ; 6(12+4)+12 ; 2x18 Ø400x132/72 ; 5(12+4) ; 2x6 ; 2x x500x57/36 ; 3(12+4) 300x500x48/36 ; 2(12+4) ; 2x6 300x500x80/36 ; 3(12+4)+12 ; 2x18 300x500x84/36 ; 2(12+4) ; 2x6 ; 2x x500x73/48 ; 4(12+4) 300x500x64/48 ; 3(12+4) ; 2x6 300x500x96/48 ; 4(12+4)+12 ; 2x18 300x500x100/48 ; 3(12+4) ; 2x6 ; 2x x500x89/60 ; 5(12+4) 300x500x80/60 ; 4(12+4) ; 2x6 300x500x112/60 ; 5(12+4)+12 ; 2x18 300x500x116/60 ; 4(12+4) ; 2x6 ; 2x x500x105/72 ; 6(12+4) 300x500x96/72 ; 5(12+4) ; 2x6 300x500x128/72 ; 6(12+4)+12 ; 2x18 300x500x132/72 ; 5(12+4) ; 2x6 ; 2x Ø450x57/36 ; 3(12+4) Ø450x48/36 ; 2(12+4) ; 2x6 Ø450x80/36 ; 3(12+4)+12 ; 2x18 Ø450x84/36 ; 2(12+4) ; 2x6 ; 2x Ø450x73/48 ; 4(12+4) Ø450x64/48 ; 3(12+4) ; 2x6 Ø450x96/48 ; 4(12+4)+12 ; 2x18 Ø450x100/48 ; 3(12+4) ; 2x6 ; 2x Ø450x89/60 ; 5(12+4) Ø450x80/60 ; 4(12+4) ; 2x6 Ø450x112/60 ; 5(12+4)+12 ; 2x18 Ø450x116/60 ; 4(12+4) ; 2x6 ; 2x Ø450x105/72 ; 6(12+4) Ø450x96/72 ; 5(12+4) ; 2x6 Ø450x128/72 ; 6(12+4)+12 ; 2x18 Ø450x132/72 ; 5(12+4) ; 2x6 ; 2x x600x57/36 ; 3(12+4) 300x600x48/36 ; 2(12+4) ; 2x6 300x600x80/36 ; 3(12+4)+12 ; 2x18 300x600x84/36 ; 2(12+4) ; 2x6 ; 2x x600x73/48 ; 4(12+4) 300x600x64/48 ; 3(12+4) ; 2x6 300x600x96/48 ; 4(12+4)+12 ; 2x18 300x600x100/48 ; 3(12+4) ; 2x6 ; 2x x600x89/60 ; 5(12+4) 300x600x80/60 ; 4(12+4) ; 2x6 300x600x112/60 ; 5(12+4)+12 ; 2x18 300x600x116/60 ; 4(12+4) ; 2x6 ; 2x x600x105/72 ; 6(12+4) 300x600x96/72 ; 5(12+4) ; 2x6 300x600x128/72 ; 6(12+4)+12 ; 2x18 300x600x132/72 ; 5(12+4) ; 2x6 ; 2x x450x57/36 ; 3(12+4) 350x450x48/36 ; 2(12+4) ; 2x6 350x450x80/36 ; 3(12+4)+12 ; 2x18 350x450x84/36 ; 2(12+4) ; 2x6 ; 2x x450x73/48 ; 4(12+4) 350x450x64/48 ; 3(12+4) ; 2x6 350x450x96/48 ; 4(12+4)+12 ; 2x18 350x450x100/48 ; 3(12+4) ; 2x6 ; 2x x450x89/60 ; 5(12+4) 350x450x80/60 ; 4(12+4) ; 2x6 350x450x112/60 ; 5(12+4)+12 ; 2x18 350x450x116/60 ; 4(12+4) ; 2x6 ; 2x x450x105/72 ; 6(12+4) 350x450x96/72 ; 5(12+4) ; 2x6 350x450x128/72 ; 6(12+4)+12 ; 2x18 350x450x132/72 ; 5(12+4) ; 2x6 ; 2x x450x121/84 ; 7(12+4) 350x450x112/84 ; 6(12+4) ; 2x6 350x450x144/84 ; 7(12+4)+12 ; 2x18 350x450x148/84 ; 6(12+4) ; 2x6 ; 2x Ø500x57/36 ; 3(12+4) Ø500x48/36 ; 2(12+4) ; 2x6 Ø500x80/36 ; 3(12+4)+12 ; 2x18 Ø500x84/36 ; 2(12+4) ; 2x6 ; 2x Ø500x73/48 ; 4(12+4) Ø500x64/48 ; 3(12+4) ; 2x6 Ø500x96/48 ; 4(12+4)+12 ; 2x18 Ø500x100/48 ; 3(12+4) ; 2x6 ; 2x Ø500x89/60 ; 5(12+4) Ø500x80/60 ; 4(12+4) ; 2x6 Ø500x112/60 ; 5(12+4)+12 ; 2x18 Ø500x116/60 ; 4(12+4) ; 2x6 ; 2x Ø500x105/72 ; 6(12+4) Ø500x96/72 ; 5(12+4) ; 2x6 Ø500x128/72 ; 6(12+4)+12 ; 2x18 Ø500x132/72 ; 5(12+4) ; 2x6 ; 2x Ø500x121/84 ; 7(12+4) Ø500x112/84 ; 6(12+4) ; 2x6 Ø500x144/84 ; 7(12+4)+12 ; 2x18 Ø500x148/84 ; 6(12+4) ; 2x6 ; 2x x500x73/48 ; 4(12+4) 400x500x64/48 ; 3(12+4) ; 2x6 400x500x96/48 ; 4(12+4)+12 ; 2x18 400x500x100/48 ; 3(12+4) ; 2x6 ; 2x x500x89/60 ; 5(12+4) 400x500x80/60 ; 4(12+4) ; 2x6 400x500x112/60 ; 5(12+4)+12 ; 2x18 400x500x116/60 ; 4(12+4) ; 2x6 ; 2x x500x105/72 ; 6(12+4) 400x500x96/72 ; 5(12+4) ; 2x6 400x500x128/72 ; 6(12+4)+12 ; 2x18 400x500x132/72 ; 5(12+4) ; 2x6 ; 2x Table of normalized dimensions of type B and C bearings as per EN with allowed capacities x500x121/84 ; 7(12+4) 400x500x112/84 ; 6(12+4) ; 2x6 400x500x144/84 ; 7(12+4)+12 ; 2x18 400x500x148/84 ; 6(12+4) ; 2x6 ; 2x x500x137/96 ; 8(12+4) 400x500x128/96 ; 7(12+4) ; 2x6 400x500x160/96 ; 8(12+4)+12 ; 2x18 400x500x164/96 ; 7(12+4) ; 2x6 ; 2x

8 # Type B EN (1) Type B Setra (3) Type C EN (2) Type C Setra (4) a 0 /Ø b 0 t i t s n (5) t so (6) T q F z F xy v xy alpha mm mm mm mm u mm mm kn kn nn rad 85 Ø550x73/48 ; 4(12+4) Ø550x64/48 ; 3(12+4) ; 2x6 Ø550x96/48 ; 4(12+4)+12 ; 2x18 Ø550x100/48 ; 3(12+4) ; 2x6 ; 2x Ø550x89/60 ; 5(12+4) Ø550x80/60 ; 4(12+4) ; 2x6 Ø550x112/60 ; 5(12+4)+12 ; 2x18 Ø550x116/60 ; 4(12+4) ; 2x6 ; 2x Ø550x105/72 ; 6(12+4) Ø550x96/72 ; 5(12+4) ; 2x6 Ø550x128/72 ; 6(12+4)+12 ; 2x18 Ø550x132/72 ; 5(12+4) ; 2x6 ; 2x Ø550x121/84 ; 7(12+4) Ø550x112/84 ; 6(12+4) ; 2x6 Ø550x144/84 ; 7(12+4)+12 ; 2x18 Ø550x148/84 ; 6(12+4) ; 2x6 ; 2x Ø550x137/96 ; 8(12+4) Ø550x128/96 ; 7(12+4) ; 2x6 Ø550x160/96 ; 8(12+4)+12 ; 2x18 Ø550x164/96 ; 7(12+4) ; 2x6 ; 2x x600x73/48 ; 4(12+4) 400x600x64/48 ; 3(12+4) ; 2x6 400x600x96/48 ; 4(12+4)+12 ; 2x18 400x600x100/48 ; 3(12+4) ; 2x6 ; 2x x600x89/60 ; 5(12+4) 400x600x80/60 ; 4(12+4) ; 2x6 400x600x112/60 ; 5(12+4)+12 ; 2x18 400x600x116/60 ; 4(12+4) ; 2x6 ; 2x x600x105/72 ; 6(12+4) 400x600x96/72 ; 5(12+4) ; 2x6 400x600x128/72 ; 6(12+4)+12 ; 2x18 400x600x132/72 ; 5(12+4) ; 2x6 ; 2x x600x121/84 ; 7(12+4) 400x600x112/84 ; 6(12+4) ; 2x6 400x600x144/84 ; 7(12+4)+12 ; 2x18 400x600x148/84 ; 6(12+4) ; 2x6 ; 2x x600x137/96 ; 8(12+4) 400x600x128/96 ; 7(12+4) ; 2x6 400x600x160/96 ; 8(12+4)+12 ; 2x18 400x600x164/96 ; 7(12+4) ; 2x6 ; 2x x600x73/48 ; 4(12+4) 450x600x64/48 ; 3(12+4) ; 2x6 450x600x96/48 ; 4(12+4)+12 ; 2x18 450x600x100/48 ; 3(12+4) ; 2x6 ; 2x x600x89/60 ; 5(12+4) 450x600x80/60 ; 4(12+4) ; 2x6 450x600x112/60 ; 5(12+4)+12 ; 2x18 450x600x116/60 ; 4(12+4) ; 2x6 ; 2x x600x105/72 ; 6(12+4) 450x600x96/72 ; 5(12+4) ; 2x6 450x600x128/72 ; 6(12+4)+12 ; 2x18 450x600x132/72 ; 5(12+4) ; 2x6 ; 2x x600x121/84 ; 7(12+4) 450x600x112/84 ; 6(12+4) ; 2x6 450x600x144/84 ; 7(12+4)+12 ; 2x18 450x600x148/84 ; 6(12+4) ; 2x6 ; 2x x600x137/96 ; 8(12+4) 450x600x128/96 ; 7(12+4) ; 2x6 450x600x160/96 ; 8(12+4)+12 ; 2x18 450x600x164/96 ; 7(12+4) ; 2x6 ; 2x x600x153/108 ; 9(12+4) 450x600x144/108 ; 8(12+4) ; 2x6 450x600x176/108 ; 9(12+4)+12 ; 2x18 450x600x180/108 ; 8(12+4) ; 2x6 ; 2x Ø600x73/48 ; 4(12+4) Ø600x64/48 ; 3(12+4) ; 2x6 Ø600x96/48 ; 4(12+4)+12 ; 2x18 Ø600x100/48 ; 3(12+4) ; 2x6 ; 2x Ø600x89/60 ; 5(12+4) Ø600x80/60 ; 4(12+4) ; 2x6 Ø600x112/60 ; 5(12+4)+12 ; 2x18 Ø600x116/60 ; 4(12+4) ; 2x6 ; 2x Ø600x105/72 ; 6(12+4) Ø600x96/72 ; 5(12+4) ; 2x6 Ø600x128/72 ; 6(12+4)+12 ; 2x18 Ø600x132/72 ; 5(12+4) ; 2x6 ; 2x Ø600x121/84 ; 7(12+4) Ø600x112/84 ; 6(12+4) ; 2x6 Ø600x144/84 ; 7(12+4)+12 ; 2x18 Ø600x148/84 ; 6(12+4) ; 2x6 ; 2x Ø600x137/96 ; 8(12+4) Ø600x128/96 ; 7(12+4) ; 2x6 Ø600x160/96 ; 8(12+4)+12 ; 2x18 Ø600x164/96 ; 7(12+4) ; 2x6 ; 2x Ø600x153/108 ; 9(12+4) Ø600x144/108 ; 8(12+4) ; 2x6 Ø600x176/108 ; 9(12+4)+12 ; 2x18 Ø600x180/108 ; 8(12+4) ; 2x6 ; 2x x600x73/48 ; 4(12+4) 500x600x64/48 ; 3(12+4) ; 2x6 500x600x96/48 ; 4(12+4)+12 ; 2x18 500x600x100/48 ; 3(12+4) ; 2x6 ; 2x x600x89/60 ; 5(12+4) 500x600x80/60 ; 4(12+4) ; 2x6 500x600x112/60 ; 5(12+4)+12 ; 2x18 500x600x116/60 ; 4(12+4) ; 2x6 ; 2x x600x105/72 ; 6(12+4) 500x600x96/72 ; 5(12+4) ; 2x6 500x600x128/72 ; 6(12+4)+12 ; 2x18 500x600x132/72 ; 5(12+4) ; 2x6 ; 2x x600x121/84 ; 7(12+4) 500x600x112/84 ; 6(12+4) ; 2x6 500x600x144/84 ; 7(12+4)+12 ; 2x18 500x600x148/84 ; 6(12+4) ; 2x6 ; 2x x600x137/96 ; 8(12+4) 500x600x128/96 ; 7(12+4) ; 2x6 500x600x160/96 ; 8(12+4)+12 ; 2x18 500x600x164/96 ; 7(12+4) ; 2x6 ; 2x x600x153/108 ; 9(12+4) 500x600x144/108 ; 8(12+4) ; 2x6 500x600x176/108 ; 9(12+4)+12 ; 2x18 500x600x180/108 ; 8(12+4) ; 2x6 ; 2x x600x169/120 ; 10(12+4) 500x600x160/120 ; 9(12+4) ; 2x6 500x600x192/120 ; 10(12+4)+12 ; 2x18 500x600x196/120 ; 9(12+4) ; 2x6 ; 2x Ø650x73/48 ; 4(12+4) Ø650x64/48 ; 3(12+4) ; 2x6 Ø650x96/48 ; 4(12+4)+12 ; 2x18 Ø650x100/48 ; 3(12+4) ; 2x6 ; 2x Ø650x89/60 ; 5(12+4) Ø650x80/60 ; 4(12+4) ; 2x6 Ø650x112/60 ; 5(12+4)+12 ; 2x18 Ø650x116/60 ; 4(12+4) ; 2x6 ; 2x Ø650x105/72 ; 6(12+4) Ø650x96/72 ; 5(12+4) ; 2x6 Ø650x128/72 ; 6(12+4)+12 ; 2x18 Ø650x132/72 ; 5(12+4) ; 2x6 ; 2x Ø650x121/84 ; 7(12+4) Ø650x112/84 ; 6(12+4) ; 2x6 Ø650x144/84 ; 7(12+4)+12 ; 2x18 Ø650x148/84 ; 6(12+4) ; 2x6 ; 2x Ø650x137/96 ; 8(12+4) Ø650x128/96 ; 7(12+4) ; 2x6 Ø650x160/96 ; 8(12+4)+12 ; 2x18 Ø650x164/96 ; 7(12+4) ; 2x6 ; 2x Ø650x153/108 ; 9(12+4) Ø650x144/108 ; 8(12+4) ; 2x6 Ø650x176/108 ; 9(12+4)+12 ; 2x18 Ø650x180/108 ; 8(12+4) ; 2x6 ; 2x Ø650x169/120 ; 10(12+4) Ø650x160/120 ; 9(12+4) ; 2x6 Ø650x192/120 ; 10(12+4)+12 ; 2x18 Ø650x196/120 ; 9(12+4) ; 2x6 ; 2x x600x94/64 ; 4(16+5) 600x600x84/64 ; 3(16+5) ; 2x8 600x600x115/64 ; 4(16+5)+16 ; 2x18 600x600x120/64 ; 3(16+5) ; 2x8 ; 2x x600x115/80 ; 5(16+5) 600x600x105/80 ; 4(16+5) ; 2x8 600x600x136/80 ; 5(16+5)+16 ; 2x18 600x600x141/80 ; 4(16+5) ; 2x8 ; 2x x600x136/96 ; 6(16+5) 600x600x126/96 ; 5(16+5) ; 2x8 600x600x157/96 ; 6(16+5)+16 ; 2x18 600x600x162/96 ; 5(16+5) ; 2x8 ; 2x x600x157/112 ; 7(16+5) 600x600x147/112 ; 6(16+5) ; 2x8 600x600x178/112 ; 7(16+5)+16 ; 2x18 600x600x183/112 ; 6(16+5) ; 2x8 ; 2x Table of normalized dimensions of type B and C bearings as per EN with allowed capacities x600x178/128 ; 8(16+5) 600x600x168/128 ; 7(16+5) ; 2x8 600x600x199/128 ; 8(16+5)+16 ; 2x18 600x600x204/128 ; 7(16+5) ; 2x8 ; 2x x600x199/144 ; 9(16+5) 600x600x189/144 ; 8(16+5) ; 2x8 600x600x220/144 ; 9(16+5)+16 ; 2x18 600x600x225/144 ; 8(16+5) ; 2x8 ; 2x

9 # Type B EN (1) Type B Setra (3) Type C EN (2) Type C Setra (4) a 0 /Ø b 0 t i t s n (5) t so (6) T q F z F xy v xy alpha mm mm mm mm u mm mm kn kn nn rad 127 Ø700x94/64 ; 4(16+5) Ø700x84/64 ; 3(16+5) ; 2x8 Ø700x115/64 ; 4(16+5)+16 ; 2x18 Ø700x120/64 ; 3(16+5) ; 2x8 ; 2x Ø700x115/80 ; 5(16+5) Ø700x105/80 ; 4(16+5) ; 2x8 Ø700x136/80 ; 5(16+5)+16 ; 2x18 Ø700x141/80 ; 4(16+5) ; 2x8 ; 2x Ø700x136/96 ; 6(16+5) Ø700x126/96 ; 5(16+5) ; 2x8 Ø700x157/96 ; 6(16+5)+16 ; 2x18 Ø700x162/96 ; 5(16+5) ; 2x8 ; 2x Ø700x157/112 ; 7(16+5) Ø700x147/112 ; 6(16+5) ; 2x8 Ø700x178/112 ; 7(16+5)+16 ; 2x18 Ø700x183/112 ; 6(16+5) ; 2x8 ; 2x Ø700x178/128 ; 8(16+5) Ø700x168/128 ; 7(16+5) ; 2x8 Ø700x199/128 ; 8(16+5)+16 ; 2x18 Ø700x204/128 ; 7(16+5) ; 2x8 ; 2x Ø700x199/144 ; 9(16+5) Ø700x189/144 ; 8(16+5) ; 2x8 Ø700x220/144 ; 9(16+5)+16 ; 2x18 Ø700x225/144 ; 8(16+5) ; 2x8 ; 2x x700x94/64 ; 4(16+5) 600x700x84/64 ; 3(16+5) ; 2x8 600x700x115/64 ; 4(16+5)+16 ; 2x18 600x700x120/64 ; 3(16+5) ; 2x8 ; 2x x700x115/80 ; 5(16+5) 600x700x105/80 ; 4(16+5) ; 2x8 600x700x136/80 ; 5(16+5)+16 ; 2x18 600x700x141/80 ; 4(16+5) ; 2x8 ; 2x x700x136/96 ; 6(16+5) 600x700x126/96 ; 5(16+5) ; 2x8 600x700x157/96 ; 6(16+5)+16 ; 2x18 600x700x162/96 ; 5(16+5) ; 2x8 ; 2x x700x157/112 ; 7(16+5) 600x700x147/112 ; 6(16+5) ; 2x8 600x700x178/112 ; 7(16+5)+16 ; 2x18 600x700x183/112 ; 6(16+5) ; 2x8 ; 2x x700x178/128 ; 8(16+5) 600x700x168/128 ; 7(16+5) ; 2x8 600x700x199/128 ; 8(16+5)+16 ; 2x18 600x700x204/128 ; 7(16+5) ; 2x8 ; 2x x700x199/144 ; 9(16+5) 600x700x189/144 ; 8(16+5) ; 2x8 600x700x220/144 ; 9(16+5)+16 ; 2x18 600x700x225/144 ; 8(16+5) ; 2x8 ; 2x Ø750x94/64 ; 4(16+5) Ø750x84/64 ; 3(16+5) ; 2x8 Ø750x115/64 ; 4(16+5)+16 ; 2x18 Ø750x120/64 ; 3(16+5) ; 2x8 ; 2x Ø750x115/80 ; 5(16+5) Ø750x105/80 ; 4(16+5) ; 2x8 Ø750x136/80 ; 5(16+5)+16 ; 2x18 Ø750x141/80 ; 4(16+5) ; 2x8 ; 2x Ø750x136/96 ; 6(16+5) Ø750x126/96 ; 5(16+5) ; 2x8 Ø750x157/96 ; 6(16+5)+16 ; 2x18 Ø750x162/96 ; 5(16+5) ; 2x8 ; 2x Ø750x157/112 ; 7(16+5) Ø750x147/112 ; 6(16+5) ; 2x8 Ø750x178/112 ; 7(16+5)+16 ; 2x18 Ø750x183/112 ; 6(16+5) ; 2x8 ; 2x Ø750x178/128 ; 8(16+5) Ø750x168/128 ; 7(16+5) ; 2x8 Ø750x199/128 ; 8(16+5)+16 ; 2x18 Ø750x204/128 ; 7(16+5) ; 2x8 ; 2x Ø750x199/144 ; 9(16+5) Ø750x189/144 ; 8(16+5) ; 2x8 Ø750x220/144 ; 9(16+5)+16 ; 2x18 Ø750x225/144 ; 8(16+5) ; 2x8 ; 2x x700x94/64 ; 4(16+5) 700x700x84/64 ; 3(16+5) ; 2x8 700x700x115/64 ; 4(16+5)+16 ; 2x18 700x700x120/64 ; 3(16+5) ; 2x8 ; 2x x700x115/80 ; 5(16+5) 700x700x105/80 ; 4(16+5) ; 2x8 700x700x136/80 ; 5(16+5)+16 ; 2x18 700x700x141/80 ; 4(16+5) ; 2x8 ; 2x x700x136/96 ; 6(16+5) 700x700x126/96 ; 5(16+5) ; 2x8 700x700x157/96 ; 6(16+5)+16 ; 2x18 700x700x162/96 ; 5(16+5) ; 2x8 ; 2x x700x157/112 ; 7(16+5) 700x700x147/112 ; 6(16+5) ; 2x8 700x700x178/112 ; 7(16+5)+16 ; 2x18 700x700x183/112 ; 6(16+5) ; 2x8 ; 2x x700x178/128 ; 8(16+5) 700x700x168/128 ; 7(16+5) ; 2x8 700x700x199/128 ; 8(16+5)+16 ; 2x18 700x700x204/128 ; 7(16+5) ; 2x8 ; 2x x700x199/144 ; 9(16+5) 700x700x189/144 ; 8(16+5) ; 2x8 700x700x220/144 ; 9(16+5)+16 ; 2x18 700x700x225/144 ; 8(16+5) ; 2x8 ; 2x x700x220/160 ; 10(16+5) 700x700x210/160 ; 9(16+5) ; 2x8 700x700x241/160 ; 10(16+5)+16 ; 2x18 700x700x246/160 ; 9(16+5) ; 2x8 ; 2x Ø800x94/64 ; 4(16+5) Ø800x84/64 ; 3(16+5) ; 2x8 Ø800x115/64 ; 4(16+5)+16 ; 2x18 Ø800x120/64 ; 3(16+5) ; 2x8 ; 2x Ø800x115/80 ; 5(16+5) Ø800x105/80 ; 4(16+5) ; 2x8 Ø800x136/80 ; 5(16+5)+16 ; 2x18 Ø800x141/80 ; 4(16+5) ; 2x8 ; 2x Ø800x136/96 ; 6(16+5) Ø800x126/96 ; 5(16+5) ; 2x8 Ø800x157/96 ; 6(16+5)+16 ; 2x18 Ø800x162/96 ; 5(16+5) ; 2x8 ; 2x Ø800x157/112 ; 7(16+5) Ø800x147/112 ; 6(16+5) ; 2x8 Ø800x178/112 ; 7(16+5)+16 ; 2x18 Ø800x183/112 ; 6(16+5) ; 2x8 ; 2x Ø800x178/128 ; 8(16+5) Ø800x168/128 ; 7(16+5) ; 2x8 Ø800x199/128 ; 8(16+5)+16 ; 2x18 Ø800x204/128 ; 7(16+5) ; 2x8 ; 2x Ø800x199/144 ; 9(16+5) Ø800x189/144 ; 8(16+5) ; 2x8 Ø800x220/144 ; 9(16+5)+16 ; 2x18 Ø800x225/144 ; 8(16+5) ; 2x8 ; 2x Ø800x220/160 ; 10(16+5) Ø800x210/160 ; 9(16+5) ; 2x8 Ø800x241/160 ; 10(16+5)+16 ; 2x18 Ø800x246/160 ; 9(16+5) ; 2x8 ; 2x x800x94/64 ; 4(16+5) 700x800x84/64 ; 3(16+5) ; 2x8 700x800x115/64 ; 4(16+5)+16 ; 2x18 700x800x120/64 ; 3(16+5) ; 2x8 ; 2x x800x115/80 ; 5(16+5) 700x800x105/80 ; 4(16+5) ; 2x8 700x800x136/80 ; 5(16+5)+16 ; 2x18 700x800x141/80 ; 4(16+5) ; 2x8 ; 2x x800x136/96 ; 6(16+5) 700x800x126/96 ; 5(16+5) ; 2x8 700x800x157/96 ; 6(16+5)+16 ; 2x18 700x800x162/96 ; 5(16+5) ; 2x8 ; 2x x800x157/112 ; 7(16+5) 700x800x147/112 ; 6(16+5) ; 2x8 700x800x178/112 ; 7(16+5)+16 ; 2x18 700x800x183/112 ; 6(16+5) ; 2x8 ; 2x x800x178/128 ; 8(16+5) 700x800x168/128 ; 7(16+5) ; 2x8 700x800x199/128 ; 8(16+5)+16 ; 2x18 700x800x204/128 ; 7(16+5) ; 2x8 ; 2x Table of normalized dimensions of type B and C bearings as per EN with allowed capacities x800x199/144 ; 9(16+5) 700x800x189/144 ; 8(16+5) ; 2x8 700x800x220/144 ; 9(16+5)+16 ; 2x18 700x800x225/144 ; 8(16+5) ; 2x8 ; 2x x800x220/160 ; 10(16+5) 700x800x210/160 ; 9(16+5) ; 2x8 700x800x241/160 ; 10(16+5)+16 ; 2x18 700x800x246/160 ; 9(16+5) ; 2x8 ; 2x

10 # Type B EN (1) Type B Setra (3) Type C EN (2) Type C Setra (4) a 0 /Ø b 0 t i t s n (5) t so (6) T q F z F xy v xy alpha mm mm mm mm u mm mm kn kn nn rad 166 Ø850x94/64 ; 4(16+5) Ø850x84/64 ; 3(16+5) ; 2x8 Ø850x115/64 ; 4(16+5)+16 ; 2x18 Ø850x120/64 ; 3(16+5) ; 2x8 ; 2x Ø850x115/80 ; 5(16+5) Ø850x105/80 ; 4(16+5) ; 2x8 Ø850x136/80 ; 5(16+5)+16 ; 2x18 Ø850x141/80 ; 4(16+5) ; 2x8 ; 2x Ø850x136/96 ; 6(16+5) Ø850x126/96 ; 5(16+5) ; 2x8 Ø850x157/96 ; 6(16+5)+16 ; 2x18 Ø850x162/96 ; 5(16+5) ; 2x8 ; 2x Ø850x157/112 ; 7(16+5) Ø850x147/112 ; 6(16+5) ; 2x8 Ø850x178/112 ; 7(16+5)+16 ; 2x18 Ø850x183/112 ; 6(16+5) ; 2x8 ; 2x Ø850x178/128 ; 8(16+5) Ø850x168/128 ; 7(16+5) ; 2x8 Ø850x199/128 ; 8(16+5)+16 ; 2x18 Ø850x204/128 ; 7(16+5) ; 2x8 ; 2x Ø850x199/144 ; 9(16+5) Ø850x189/144 ; 8(16+5) ; 2x8 Ø850x220/144 ; 9(16+5)+16 ; 2x18 Ø850x225/144 ; 8(16+5) ; 2x8 ; 2x Ø850x220/160 ; 10(16+5) Ø850x210/160 ; 9(16+5) ; 2x8 Ø850x241/160 ; 10(16+5)+16 ; 2x18 Ø850x246/160 ; 9(16+5) ; 2x8 ; 2x x800x110/80 ; 4(20+5) 800x800x100/80 ; 3(20+5) ; 2x10 800x800x131/80 ; 4(20+5)+20 ; 2x18 800x800x136/80 ; 3(20+5) ; 2x10 ; 2x x800x135/100 ; 5(20+5) 800x800x125/100 ; 4(20+5) ; 2x10 800x800x156/100 ; 5(20+5)+20 ; 2x18 800x800x161/100 ; 4(20+5) ; 2x10 ; 2x x800x160/120 ; 6(20+5) 800x800x150/120 ; 5(20+5) ; 2x10 800x800x181/120 ; 6(20+5)+20 ; 2x18 800x800x186/120 ; 5(20+5) ; 2x10 ; 2x x800x185/140 ; 7(20+5) 800x800x175/140 ; 6(20+5) ; 2x10 800x800x206/140 ; 7(20+5)+20 ; 2x18 800x800x211/140 ; 6(20+5) ; 2x10 ; 2x x800x210/160 ; 8(20+5) 800x800x200/160 ; 7(20+5) ; 2x10 800x800x231/160 ; 8(20+5)+20 ; 2x18 800x800x236/160 ; 7(20+5) ; 2x10 ; 2x x800x235/180 ; 9(20+5) 800x800x225/180 ; 8(20+5) ; 2x10 800x800x256/180 ; 9(20+5)+20 ; 2x18 800x800x261/180 ; 8(20+5) ; 2x10 ; 2x x800x260/200 ; 10(20+5) 800x800x250/200 ; 9(20+5) ; 2x10 800x800x281/200 ; 10(20+5)+20 ; 2x18 800x800x286/200 ; 9(20+5) ; 2x10 ; 2x Ø900x110/80 ; 4(20+5) Ø900x100/80 ; 3(20+5) ; 2x10 Ø900x131/80 ; 4(20+5)+20 ; 2x18 Ø900x136/80 ; 3(20+5) ; 2x10 ; 2x Ø900x135/100 ; 5(20+5) Ø900x125/100 ; 4(20+5) ; 2x10 Ø900x156/100 ; 5(20+5)+20 ; 2x18 Ø900x161/100 ; 4(20+5) ; 2x10 ; 2x Ø900x160/120 ; 6(20+5) Ø900x150/120 ; 5(20+5) ; 2x10 Ø900x181/120 ; 6(20+5)+20 ; 2x18 Ø900x186/120 ; 5(20+5) ; 2x10 ; 2x Ø900x185/140 ; 7(20+5) Ø900x175/140 ; 6(20+5) ; 2x10 Ø900x206/140 ; 7(20+5)+20 ; 2x18 Ø900x211/140 ; 6(20+5) ; 2x10 ; 2x Ø900x210/160 ; 8(20+5) Ø900x200/160 ; 7(20+5) ; 2x10 Ø900x231/160 ; 8(20+5)+20 ; 2x18 Ø900x236/160 ; 7(20+5) ; 2x10 ; 2x Ø900x235/180 ; 9(20+5) Ø900x225/180 ; 8(20+5) ; 2x10 Ø900x256/180 ; 9(20+5)+20 ; 2x18 Ø900x261/180 ; 8(20+5) ; 2x10 ; 2x Ø900x260/200 ; 10(20+5) Ø900x250/200 ; 9(20+5) ; 2x10 Ø900x281/200 ; 10(20+5)+20 ; 2x18 Ø900x286/200 ; 9(20+5) ; 2x10 ; 2x x900x110/80 ; 4(20+5) 900x900x100/80 ; 3(20+5) ; 2x10 900x900x131/80 ; 4(20+5)+20 ; 2x18 900x900x136/80 ; 3(20+5) ; 2x10 ; 2x x900x135/100 ; 5(20+5) 900x900x125/100 ; 4(20+5) ; 2x10 900x900x156/100 ; 5(20+5)+20 ; 2x18 900x900x161/100 ; 4(20+5) ; 2x10 ; 2x x900x160/120 ; 6(20+5) 900x900x150/120 ; 5(20+5) ; 2x10 900x900x181/120 ; 6(20+5)+20 ; 2x18 900x900x186/120 ; 5(20+5) ; 2x10 ; 2x x900x185/140 ; 7(20+5) 900x900x175/140 ; 6(20+5) ; 2x10 900x900x206/140 ; 7(20+5)+20 ; 2x18 900x900x211/140 ; 6(20+5) ; 2x10 ; 2x x900x210/160 ; 8(20+5) 900x900x200/160 ; 7(20+5) ; 2x10 900x900x231/160 ; 8(20+5)+20 ; 2x18 900x900x236/160 ; 7(20+5) ; 2x10 ; 2x x900x235/180 ; 9(20+5) 900x900x225/180 ; 8(20+5) ; 2x10 900x900x256/180 ; 9(20+5)+20 ; 2x18 900x900x261/180 ; 8(20+5) ; 2x10 ; 2x x900x260/200 ; 10(20+5) 900x900x250/200 ; 9(20+5) ; 2x10 900x900x281/200 ; 10(20+5)+20 ; 2x18 900x900x286/200 ; 9(20+5) ; 2x10 ; 2x x900x285/220 ; 11(20+5) 900x900x275/220 ; 10(20+5) ; 2x10 900x900x306/220 ; 11(20+5)+20 ; 2x18 900x900x311/220 ; 10(20+5) ; 2x10 ; 2x Notes (1) Standard composition as per EN with 2.5 mm thick upper and lower rubber covers The bearing name is "width" x "length" x "height" / "total thickness of active rubber (excluding covers)" ; "number of internal rubber layers" ( "rubber layer thickness" + "reinforcing steel plate thickness" ) Ex: bearing #1: 100 mm in width, 150 mm in length, 30 mm in height, 16 mm thick active rubber which is composed of 2 rubber layers of 8 mm in thickness, 3 reinforcing steel plate of 3 mm in thickness, 2 rubber covers of 2.5 mm in thickness (2) The bearing name is "width" x "length" x "height" / "total thickness of active rubber" ; "number of internal rubber layers" ( "rubber layer thickness" + "reinforcing steel plate thickness" ) ; "number of outer steel plates" x "outer steel plate thickness" Ex: bearing #1: 100 mm in width, 150 mm in length, 30 mm in height, 16 mm thick active rubber which is composed of 2 rubber layers of 8 mm in thickness, 1 reinforcing steel plate of 3 mm in thickness, 2 outer steel plates of 15 mm in thickness (3) Composition as per Setra requirement with active rubber covers whom the thickness equals the half thickness of internal rubber layers The bearing name is "width" x "length" x "height" / "total thickness of active rubber (including covers)" ; "number of internal rubber layers" ( "rubber layer thickness" + "reinforcing steel plate thickness" ) ; "number of rubber covers" x "rubber cover thickness" Ex: bearing #1: 100 mm in width, 150 mm in length, 22 mm in height, 16 mm thick active rubber which is composed of 1 internal rubber layer of 8 mm in thickness and 2 rubber covers of 4 mm in thickness, 2 reinforcing steel plates of 3 mm in thickness (4) The composition is the same than (3) plus outer steel plates The bearing name is "width" x "length" x "height" / "total thickness of active rubber (including covers)" ; "number of internal rubber layers" ( "rubber layer thickness" + "reinforcing steel plate thickness" ) ; "number of rubber covers" x "rubber cover thickness" ; "number of outer steel plates" x "outer steel plate thickness" Ex: bearing #1: 100 mm in width, 150 mm in length, 22 mm in height, 16 mm thick active rubber which is composed of 1 internal rubber layer of 8 mm in thickness and 2 rubber covers of 4 mm in thickness, 2 reinforcing steel plates of 3 mm in thickness, 2 outer plates of 15 mm in thickness (5) For a composition as per Setra requirement, "n" equals "the number of internal rubber layer + the both half-layers (rubber covers)" (6) The thickness of active rubber is the total thickness of rubber under distorsion: excluding 2.5 mm thick rubber covers for a compostion as per EN and including rubber covers which equals the half thickbness of internal rubber layer for a composition as per Setra requirement Permissive values are indicative values at Ultimate Limit State. All values may not be obtained for the same loading case. Table of normalized dimensions of type B and C bearings as per EN with allowed capacities

11 Applications Techniques des Caoutchoucs et des Plastiques 1 Rue des Gaillards, ZAC des Doucettes, Garges-lès-Gonesse, France Tel : Fax : Website : For any request, please contact: Mr. Nicolas GRANIER Tel Mob nicolas.granier@atcp.net or our website

12 Laminated elastomeric bearings, ATCPAD ATCP masters in its own factory the whole process of manufacturing of laminated elastomeric bearings: - design as per technical data given by bridge designers - formula development and mixings - steel plates cutting and treatment - bearings confection - vulcanization - quality controls and testing of final products (also controled and tested by independant laboratory when required by the CE marking or project specifications) Person to contact : Mr. Nicolas GRANIER Tel or Mob nicolas.granier@atcp.net