<50 g/l sq. ft. Touch 30 minutes Re-coat 1-2 hours. <400 g/l sq. ft. Touch 30 minutes Re-coat 1-2 hours

Transcription

1 Product Guide

2 2

3 SPECIALTY PRIMERS Aqua-Lock Plus [AQ-0400] [XA01] US Aqua-Lock Plus is a 100% acrylic primer developed to provide excellent adhesion and stain blocking properties when applied to a variety of interior and exterior surfaces. This product provides a basecoat for both latex and oil-based finish coatings. It offers excellent stain blocking properties for water stains, fingerprints, smoke, crayons and more. 39% <50 g/l sq. ft. Touch 30 minutes Re-coat 1-2 hours White and deep base Prime-Lock [PS-7000] [XA13] US * Prime-Lock is a fast drying alkyd coating designed to seal a variety of stains by encapsulating the stain to prevent bleeding. This sealer/stain killer is effective in sealing stains from smoke, and smoke odor, water, rust, ink, pencil, crayon, graffiti, sappy knots and tannic acid from redwood and cedar. Severe stains may require two or more coats for positive sealing. *Prime-Lock is intended for interior and exterior use. 47% <400 g/l sq. ft. Touch 30 minutes Re-coat 1-2 hours Prime-Lock Plus [PS-8000] [XA02] US * Prime-Lock Plus is a VOC compliant primer designed to seal a variety of stains by encapsulating the stain to prevent bleeding. This sealer/stain killer is effective in sealing stains from smoke, and smoke odor, water, rust, ink, pencil, crayon, graffiti, sappy knots and tannic acid from redwood and cedar. Severe stains may require two or more coats for positive sealing. *Prime-Lock Plus is intended for interior and exterior use. 56% <350 g/l sq. ft. Touch 30 minutes Re-coat 1-2 hours Odor-Less [NO-4000] [XA03] US Odor-Less Alkyd is a virtually odorless, solvent based, quick drying sealer which is effective over a broad spectrum of stains, many which are difficult to seal with a water based stain killer. Odor-Less Alkyd can be used over water, tannin, smoke, rust, pencil, ink, nicotine, coffee and most other stains. Any slight odor detected is more mild than latex paint, not offensive and dissipates in 15 minutes. Odor-Less Alkyd can be used on bare or previously painted surfaces. 57% <350 g/l sq. ft. Touch 30 minutes Re-coat 1-2 hours Seal-Lock [IL-6600] [XA04] US Seal-Lock is an alcohol-based flat primer/sealer that stops bleeding on plaster, wood, metal and masonry. It is ideal as a replacement for pigmented shellac, although it does not contain shellac. Seal-Lock may be used as a primer for porous wallboard, plasterboard, drywall and plywood; as a sealer for hot plaster, asphalt coatings, plaster walls, wood, multicolor finishes, and metal; and as a stain killer for creosote, asphalt, crayons, ink, redwood and cedar. Applicable for interior or exterior use. For exterior use, spot prime only. Seal-Lock is also suitable for use as a vapor barrier (perm rating of 0.3). 41% <480 g/l sq. ft. Touch 15 minutes Re-coat 2 hours 3

4 One Prep Water Based Pre-Wallcovering Primer [WP-3001] [XA21] US One Prep is an acrylic waterborne primer/sealer that provides a moisture resistant foundation on all interior surfaces, new and previously painted. It is intended to be used under all types of wall-coverings and will allow for easy removal when the time comes. As a primer/sealer, One Prep can also be coated with any latex or oil based finish paint. In addition to white, One Prep comes in a clear that can be applied as is or tinted with universal colorants to match the color of the wall-covering. 27% <100 g/l sq. ft. Touch 1 hour Re-coat 2 hours White and deep base Stix Waterborne Bonding Primer [SXA-110] [XA05] US Stix Waterborne Bonding Primer is a premium quality, waterborne, acrylic urethane primer-sealer with unparalleled adhesion to the most challenging surfaces including PVC, vinyl, plastic, glass, tile, glazed block, glossy paints, pre-coated siding, fiberglass, and galvanized metals. Stix is also ideal for use on plaster, drywall, wood, and non-ferrous metals. It cures in temperatures as low as 35 F and offers an extremely hard film when cured. Use it on interior and exterior surfaces and topcoat with almost any type of coating including alkyd, acrylic latex, urethane, epoxy, and lacquer finishes. 40% <150 g/l sq. ft. Touch 30 minutes Re-coat 3-4 hours Stix Solvent Bonding Primer [SXS-110] [XA06] US Stix Solvent Bonding Primer is a premium, modified alkyd primer sealer with unparalleled adhesion to the most challenging surfaces including PVC, vinyl, fiberglass, tile, glazed block, and glass. Stix provides a sound primed surface for all types of finish coats: oil, latex, epoxy, urethanes, 2-pack urethanes and polyesters. Stix may be used on all interior and exterior surfaces. 53% <400 g/l sq. ft. Touch 45 minutes Re-coat 3-4 hours SPECIALTY PAINTS Hot Trax [HTF-XXX] Hot Trax Acrylic Latex Satin Concrete and Garage Floor Paint is a high performance, ready to use, water-based floor coating that resists marring common to driveways and garage floors. This finish is extremely resistant to chemicals, water, oil and gasoline. Hot Trax is also ideal for use on exterior concrete, masonry, stucco, cinderblock and brick. This durable finish is resistant to cracking. 29% <200 g/l sq. ft. Touch 2-4 hours Re-coat 24 hours Vehicular Traffic 3-4 days 4 ready-mixed colors, tintable white, and accent base 4

5 Sure-Step [SU-XXXX] [XA11] US * Sure-Step provides a durable skid-resistant finish for interior or exterior application. Imparts excellent color retention, abrasion resistance and resistance to ponding water. The slip coefficient of this product is rated as >1. Sure-Step is water reduced which allows for fast dry plus easy application and clean up. Available in six ready-mixed colors, white and also a clear finish. *Clear should only be used on bare concrete as a standalone sealer or as a sealer under the textured Sure-Step. Do not use as a top-coat over the Sure-Step textured finishes. Not for vehicular traffic. 38% <150 g/l sq. ft. Touch 1-2 hours Re-coat 8 hours Foot Traffic 24 hours 6 ready-mixed colors, tintable white, and clear WaterBlock Masonry Waterproofing Coating [MW-1000] [XA12] US WaterBlock Acrylic Masonry Waterproofer is designed to waterproof interior or exterior masonry surfaces such as basement walls, foundations, retaining walls, exterior masonry walls, etc. It is alkali resistant and will withstand hydrostatic pressure up to 12 PSI, far exceeding that of traditional latex waterproofers. WaterBlock applies like a latex paint and dries to a smooth flat finish. Apply directly to bare, vertical masonry surfaces. 45% <120 g/l sq. ft. Touch 1 hour Re-coat 4 hours Garage Guard Epoxy [EGG-XXX] [XA09] US Garage Guard Epoxy is a new generation water-based catalyzed epoxy which offers performance equal to traditional solvent based epoxy systems. It provides superior chemical, abrasion and impact resistance when compared to conventional waterborne epoxies. The highly cross-linked film provides years of service in industrial and commercial applications. Garage Guard Epoxy produces lower odor than solvent-based epoxies, so this product may be applied in occupied areas, and is more environmentally and user friendly. USDA approved for food contact. This is a two component product with a mix ratio of 3:1. 38% <150 g/l sq. ft. Touch 1-2 hours, Re-coat 8 hours, Foot Traffic 24 hours Vehicular Traffic 72 hours 2 ready-mixed colors, tint base, and neutral base CabinetCoat Acrylic Satin Enamel [CC-45XX] [XA20] US CabinetCoat is the ultimate finish for refurbishing kitchen and bathroom cabinets, shelving, furniture and other interior applications that require an ultra-smooth, factory like finish with long lasting beauty. Its super adhering quality allows painting hard to stick surfaces, even polyurethane and varnish, without using a primer. Approved by the Kitchen Cabinet Manufacturers Association (KCMA). 33% <50 g/l sq. ft. Touch 1-2 hours Re-coat 4-6 hours White and tint base Insl-Cap Lead Encapsulating Compound [EC-3110] * Insl-Cap is a heavy-bodied, interior water-based coating designed to create a safe barrier over lead containing paints. Insl-Cap conforms to all of the requirements of the Commonwealth of Massachusetts Encapsulation Product Performance Protocol, Department of Public Health (Reg. #DL-10019). Meets HUD requirements for lead encapsulants. Contains Bitrex a bitter tasting, anti-ingestant that deters children from eating paint. *Can be top-coated with latex paints. 40% <50 g/l sq. ft. Touch 2-4 hours Re-coat 12 hours 5

6 Super Dampwall Gloss Enamel [SE-0410] Super Dampwall is a non-toxic, odorless coating formulated with special resins designed especially for use on walls and ceilings in dairies and food processing plants. Can be applied to damp surfaces. 54% <360 g/l sq. ft. Touch 4-6 hours Re-coat 12 hours Pro-Plate Interior/Exterior Alkyd Gloss [BO387-XX] * A rust preventative, polyurethane reinforced enamel with outstanding durability and scuff resistance. This product provides excellent protection for new and previously painted metal surfaces. It withstands all kinds of weather and resists dirt and marring. *This product also meets the more stringent Industrial Maintenance Coating VOC level of 340g/l. When used in industrial or professional applications, this product may be used on most surfaces including wood, concrete, masonry, drywall, etc. 48% <340 g/l sq. ft. Touch 4-8 hours Re-coat hours White, black and 7 ready-mixed colors FreezerKote [FK-1310] * FreezerKote is a high-gloss, non-yellowing white coating designed for application from ambient to sub-freezing temperatures. FreezerKote is USDA approved. Can be applied when surface and ambient temperatures are between -30 and 40 o F. *Product contains alcohol. Care should be taken to avoid absorption by unsealed food. 60% <340 g/l sq. ft. Touch 1-2 hours Re-coat 4 hours White and safety yellow ElectroKote Alkyd Enamel [EQD-5XX] ElectroKote (low VOC Electrostatic) Alkyd Enamel is a quick drying, satin sheen, alkyd enamel specially formulated for electrostatic spray application. It dries to the touch in 15 minutes to a satin mar-resistant finish resulting in minimal out of service time. ElectroKote Alkyd Enamel meets the requirements of USDA approval for incidental food contact. ElectroKote Epoxy Enamel [EE-60XX] * ElectroKote Electrostatic Epoxy is a two component product designed for electrostatic application where maximum durability, abrasion resistance, chemical resistance and moisture resistance is required. This product is pre-polarized for spray with most electrostatic equipment and when properly applied, levels to a uniform finish. Caution should be taken when using this product in exterior applications as UV light will cause premature chalking and fading. This is a two component product that requires 1 part of A or Base, and 1 Part of B component (EE-60BS). *Approved for shop application only in OTC regulated areas. 6

7 SILATHANE PRIMERS AND ENAMELS Silathane Tannin Blocking Primer [SP ] A superior quality tannin blocking primer designed for interior and exterior application on wood substrates. It builds well on sharp edges, may be sanded after overnight drying and provides a smooth, stain blocking foundation for all topcoats. 56% <350 g/l sq. ft. Touch 2-4 hours Re-coat hours Silathane Rust Proof Metal Primer [SPF ] A rust inhibitive metal primer for use on structural steel, aluminum, copper, magnesium, iron and other metal surfaces requiring a non-corrosive metal primer. Use on gutters, down spouts, metal sash, fire escapes, metal furniture, railings, vehicles, tanks, machinery & other metal surfaces. Meets USDA criteria for use in federally inspected meat and poultry plants. 53% <340 g/l sq. ft. Touch 2-4 hours Re-coat 12 hours White, gray/green, and red oxide Silathane II Interior/Exterior Rust Proof Metal Primer [SP ] This is a water reducible acrylic metal primer for coating steel, pre-engineered metal building parts and other steel that is exposed to a normal commercial or residential environment. It may be used in areas where solvent fumes are a problem or where ecological concerns dictate. May be top-coated with conventional alkyd, oil based and latex type paints. It may also be used as a tie-coat over zinc rich primers. Provides protection from rust bleed and flash rust. An excellent choice for galvanized metal. 42% <220 g/l sq. ft. Touch 1 hour Re-coat 2-4 hours Silathane Interior/Exterior Alkyd Gloss Enamel [SP-520-XX] * Silithane Alkyd Gloss has excellent gloss and color retention. It provides excellent protection for equipment, machinery, ironwork and tools. This product meets USDA criteria for indirect food contact; resistant to dirt collection; has excellent flow and leveling characteristics and is mercury and lead free. *Also available in a semi-gloss finish [SP-521-XX]. Technical data is the same for both finishes. 56% <340 g/l sq. ft. Touch 2-4 hours Re-coat hours White, black, multiple ready-mixed colors and a full line of bases Silathane II Interior/Exterior Acrylic Gloss Enamel [SP-532-XX] * Silathane II provides a rust inhibitive system for use on primed or previously painted interior or exterior metal, wood, masonry, plastic and composition surfaces. It has excellent gloss and color retention under the toughest conditions. It is extremely durable and mar, chip and weather resistant, making it an ideal coating for equipment, machinery, ironwork, and other surfaces needing a durable gloss finish. *Also available in a semi-gloss finish [SP-533-XX]. Technical data is the same for both finishes. 36% <250 g/l sq. ft. Touch 1-2 hours Re-coat 4-6 hours White, black, multiple ready mixed colors, and a full line of bases 7

8 PRODUCT COMPLIANCE STATUS Insl-X Products LEED Line Product Description VOC Actual Product Classification (For LEED/Green Seal) Product Classification (For AIM/OTC) Meets LEED Criteria AQ-0400 Aqua-Lock Plus 40 Int/Ext Flat Primer Specialty Primer 50 PS-7000 Prime-Lock 395 Int/Ext Flat Primer QD Primer 50 PS-8000 Prime-Lock Plus 336 Int Flat Primer Specialty Primer 50 NO-4000 Odor-Less Primer 320 Int Flat Primer Specialty Primer 50 IL-6600 Seal-Lock Primer/Sealer/Stain Killer 468 Specialty Primer Shellac-Op / Spec Primer* 50 WP-3001 One Prep Wallpaper Primer 98 Int Flat Primer Primer 50 SXA-110 Stix Acrylic Bonding Primer 152 Int/Ext Flat Primer Primer 50 SXS-110 Stix Solvent Bonding Primer 396 Int/Ext Flat Primer QD Primer 50 HTF-100 Hot-Trax Non-Skid Acrylic Garage 200 Floor Coating Floor Paint 100 MW-1000 WaterBlock 118 Waterproofing Coating WPer - Concrete/Masonry 250 EGG-310 Garage Guard WB Epoxy 231 Floor Coating Floor Paint 100 CC-4500 Cabinet Coat Acrylic Satin Enamel 48 Int Non Flat Non Flat - S 150 EC-3110 Insl-Cap Lead Encapsulator 44 Int/Ext Non Flat Flat - S 50 SE-0410 Super Damp Wall Gloss Enamel 355 Waterproofing Coating Industrial Maint. Ctg 250 BO387-XX Pro-Plate Alkyd Enamel 361 Rust Preventative Ctg Rust Preventative Ctg 250 FK-1310 FreezerKote 314 Int Non Flat Industrial Maint. Ctg 150 EQD-0500 Low VOC ElectroKote Alkyd Enamel 340 Int/Ext Non Flat Industrial Maint. Ctg 150 EE-6000 ElectroKote Epoxy Enamel 477 Int/Ext Non Flat (Industrial) Industrial Maint. Ctg 150 SP520 Silathane Alkyd Gloss 336 Rust Preventative Ctg Industrial Maint. Ctg 250 SP521 Silathane Alkyd Semi-Gloss 324 Rust Preventative Ctg Industrial Maint. Ctg 250 SA532 Silathane II Acrylic Gloss 201 Int/Ext Non Flat Non Flat High Gloss 150 SA533 Silathane II Semi-Gloss 136 Int/Ext Non Flat Non Flat - S 150 TP-2200 Zone Marking Paint 90 Ext Flat Traffic Paint Traffic Paint No LEED Systems Apply TP-2400 Alkyd Zone Paint 349 Ext Flat Zone Marking Zone Marking No LEED Systems Apply CR-2600 Chlorinated Rubber Pool Paint 564 Pool Paint Pool Paint No LEED Systems Apply WR-1000 Waterborne Pool Paint 149 Pool Paint Pool Paint No LEED Systems Apply RP-27XX Rubber Based Pool Paint 338 Pool Paint Pool Paint No LEED Systems Apply IG-4000 Insl-Guard Epoxy Pool Paint 331 Pool Paint Pool Paint No LEED Systems Apply TRC-035 Tennis Court Patch N Level 47 Ext Tennis Court Ctg Floor Paint No LEED Systems Apply TRC-007 Tennis Court Bond Coat 96 Ext Tennis Court Ctg Floor Paint No LEED Systems Apply TRC-040 Tennis Court Filler Coat 72 Ext Tennis Court Ctg Floor Paint No LEED Systems Apply TRC-060 Tennis Court Cushion Coat 70 Ext Tennis Court Ctg Floor Paint No LEED Systems Apply TRC-08x Tennis Court Finishes - Smooth 143 Ext Tennis Court Ctg Floor Paint No LEED Systems Apply TRC-037/38 Tennis Court Line Marking Paints 100 Ext Tennis Court Ctg Floor Paint No LEED Systems Apply GS-11 VOC GC-3 VOC SCAQMD (2004) * VOC regulations are regularly being updated and revised. While the above is accurate as of printing, please check with local authorities for the most current VOC regulations. 8

9 EPA AIM Current NATL / EPA OTC / LADCO California MPI EPA Current Compliance EPA 2011 EPA 2011 Compliance OTC/ LADCO Current OTC/ LADCO Current Compliance OTC 2010 OTC 2010 Compliance CARB Current CARB 2010 SCAQMD Current (2007) MPI Categories Approved GPS1 GPS2 350 Yes 350 Yes 350 Yes 350 Yes Yes 350 No 200 No 200 No Yes 350 Yes 350 Yes 350 Yes Yes 350 Yes 350 Yes 350 Yes No 350 No 350 No 350 No , Yes 250 Yes 250 Yes 200 Yes Yes 250 Yes 250 Yes 200 Yes Yes 350 No 350 No 200 No Yes 250 Yes 250 Yes 250 Yes Yes 250 Yes 400 Yes 150 Yes Yes 250 Yes 250 Yes 250 Yes Yes 150 No 150 No 150 No Yes 100 Yes 100 Yes 100 Yes Yes 340 No 340 No 250 No Yes 400 Yes 400 Yes 400 Yes Yes 340 Yes 340 Yes 250 No Yes 340 Yes 340 Yes 250 No Yes 340 No 340 No 250 No Yes 340 Yes 340 Yes 250 No , Yes 340 Yes 340 Yes 250 No Yes 250 Yes 250 Yes 250 Yes Yes 150 Yes 150 Yes 150 Yes Yes 150 Yes 150 Yes 150 Yes Yes 150 No 150 No 150 No Yes 340 No 340 No 340 No Yes 340 Yes 340 Yes 340 Yes Yes 340 Yes 340 Yes 340 Yes Yes 340 Yes 340 Yes 340 Yes Yes 250 Yes 250 Yes 250 Yes Yes 250 Yes 250 Yes 250 Yes Yes 250 Yes 250 Yes 250 Yes Yes 250 Yes 250 Yes 250 Yes Yes 250 Yes 250 Yes 250 Yes Yes 250 Yes 250 Yes 250 Yes

10 TRAFFIC PAINT Acrylic Latex Zone Paint [TP-22XX] A fast drying paint for marking traffic lanes on streets, highways, parking lots, warehouses and other areas where such marking is required. Traffic beads may be dropped into this coating while wet to provide light reflecting markings. If beads are applied, they should be broadcast into the wet paint at a rate of 6 pounds of beads per gallon of paint. 34% <100 g/l 3" line ft., 4" line ft., 5" line ft., 6" line ft. Touch 30 minutes Re-coat 4 hours White, black, yellow, and handicap blue Alkyd Zone Marking Paint [TP-24XX] A fast drying alkyd traffic paint for marking lanes on parking lots, warehouses, airports, curbs, and other areas where such marking is required. Traffic beads may be dropped into this coating while wet to provide light reflecting markings. If beads are applied, they should be broadcast into the wet paint at a rate of 6 pounds of beads per gallon of paint. 53% <350 g/l 3" line ft., 4" line ft., 5" line ft., 6" line ft. Touch 30 minutes Re-coat 4 hours White, black, red, yellow, and handicap blue SPECIALTY PAINTS Chlorinated Rubber Pool Paint [CR-26XX] * Insl-x Chlorinated Rubber Pool Paint is a premium quality coating that offers excellent chemical and abrasion resistance and can be applied over most existing chlorinated rubber or pliolite based pool paints in good condition. This paint may also be used on bare concrete, marcite, gunite and other masonry surfaces in sound condition. *See Insl-x Swimming Pool Paint Brochure for complete instructions regarding application. 32% <565 g/l sq. ft. Touch 30 minutes Re-coat 24 hours White, black, ocean blue, royal blue, red, and aquamarine Waterborne Pool Paint [WR-10XX] [XA08] US * A new generation of waterborne, acrylic emulsion pool paint which can be applied over most types of pool coatings in good condition, as well as bare concrete or plaster surfaces. Environmentally friendly, low VOC. WR-1000 Series pool paint can be applied to damp surfaces, dries quickly for re-coating, and withstands continuous submersion in fresh and salt water. *See Insl-x Swimming Pool Paint Brochure for complete instructions regarding application. 67% <130 g/l sq. ft. Touch 1-2 hours Re-coat 4-6 hours White, black, ocean blue, royal blue, red, and aquamarine 10

11 Rubber Based Pool Paint [RP-27XX] [XA07] US * A rubber based coating for new or old concrete pools. This product complies with current volatile emission (VOC) standards outlined by the Ozone Transport Commission (OTC). It provides a durable low sheen finish for use in residential and commercial pools. Suitable for use in fresh or salt water. Resists fading, fungus, algae, abrasion and alkalis. For repaints, Rubber Based Pool Paint should only be applied over a chlorinated rubber or another synthetic rubber based pool paint. *See Insl-x Swimming Pool Paint Brochure for complete instructions regarding application. 59% 62% <340 g/l sq. ft. Touch 30 minutes Re-coat 24 hours <340 g/l sq. ft. Touch 1-2 hours Re-coat 4-6 hours White, black, ocean blue, royal blue, red, and aquamarine Insl-Guard Epoxy Pool Paint [IG-4000] * Insl-Guard Epoxy Pool Paint is a two component polyamide epoxy coating especially designed for concrete, marcite, gunite, fiberglass and steel pools. It is extremely durable in fresh and salt water and is resistant to common pool chemicals. For a complete review of application instructions, see the Insl-x Swimming Pool Paint Brochure. This product is USDA approved. This is a two component product with a mix ratio of 1:1. It requires 1 part of the proper A or base component mixed with 1 part of the proper B or converter component. *Do not mix partial kits! See Insl-x Swimming Pool Paint Brochure for complete instructions regarding application. White, black, ocean blue, royal blue, red, and aquamarine Citrus Based Cleaner [PC-2000] Citrus Based Cleaner is an industrial strength, bio-degradable, phosphate free, emulsifying cleaner based on a natural citrus by-product. Citrus Based Cleaner is the recommended cleaner with all Insl-X swmming pool paints and also cleans surfaces such as metals, masonry, painted surfaces, glass, upholstery, carpets, tile, plastics, etc. VOC <190 g/l TRU-FLEX TENNIS COURT COATINGS * Patch-n-Level [TRC-035] Patch-n-Level is a ready to use, non-shrinking, non-cracking patching compound that is formulated with special acrylic emulsions and fillers. This product fulfills the need for a superior tennis court patch and is primarily used to fill bird bath areas. The flexible film is not affected by heat or cold and possesses a high degree of breathing ability, enabling normal moisture to pass through as vapor, without causing any rupturing of the surface. 60% <50 g/l N/A Touch 2-24 hours (depending on thickness) Neutral Concrete Bond Coat Concentrate [TRC-007] Concrete Bond Coat is formulated with an acrylic polymer especially designed for promoting adhesion of Tru-Flex recreational coatings to Portland cement based concrete tennis courts. This product is formulated for onsite dilution prior to use. 46% <100 g/l 120 ft. - 2 per gallon (undiluted), 60 ft. - 2 per gallon (diluted) Touch 30 minutes Re-coat 1 hour Clear * Tennis Court Coatings are applied in a different manner than most paints and coatings and square foot coverage cannot be calculated using traditional methods. Please follow the coverage guidelines suggested on the product data sheets. 11

12 Filler Coat [TRC-040] Filler Coat consists of 100% acrylic emulsions, special reinforcing pigments and pure silica sand that provides a uniform and controlled texture. The TRC-040 Filler Coat system is suitable for all climatic conditions and protects asphalt courts from the ultra-violet rays of the sun. The TRC-040 System dries rapidly and allows moisture vapor to pass through the dried film. This coating, used in conjunction with recommended Tru-Flex topcoat system, will provide unsurpassed play characteristics. This product is formulated for onsite dilution prior to use. 61% <80 g/l sq. ft. Touch 30 minutes Re-coat 2-4 hours Neutral Rubberized Cushion Coat [TRC-060] Rubberized Cushion Coat is a high performance coating consisting of encapsulated rubber particles and fillers, carefully blended with 100% acrylic emulsion, to create a shock absorbing type of color surface when used as part of the Tru-Flex system. A Rubberized Cushion Coat surface has a pleasing, uniform texture and adds resilience to asphalt and concrete court surfaces. The flexible film is not affected by heat or cold and possesses a high degree of breathability, enabling normal moisture to pass through as vapor without causing any rupturing of the color coat. This product is formulated for onsite dilution prior to use. 43% <80 g/l sq. ft. Touch 30 minutes Re-coat 2-4 hours Clear Colored Finish Coats Smooth [TRC-08X] TRC 80 Series Finish Coat is a high performance 100% acrylic emulsion coating, highly pigmented with prime color and reinforcing pigments that will provide a long lasting finish for tennis and athletic courts. The TRC 80 Series Finish Coat is used over the TRC 40 Filler Coat Series and protects asphalt from the ultraviolet rays of the sun and makes black surfaces o F cooler. The TRC 80 Series Finish Coatings are high performance finish coatings for the Tru-Flex build up court systems. This coating, used in conjunction with the recommended Tru-Flex base system, TRC-40 and TRC-60, will provide unsurpassed play characteristics and durability. 26% <150 g/l Follow label Touch 30 minutes instructions Re-coat 2-4 hours Green, red, blue, and dark green Colored Finish Coats Textured [TRC-28X] TRC-200 Series ready to use tennis court coating is a 100% acrylic coating for application over asphalt and concrete surfaces. It delivers a durable, textured all-weather court surface, in one application and does not require extensive build up coats to provide an adequate playable surface. It provides an economical option to court installations and resurfacing. It combines the latest technology and provides effective protection against sunlight, extreme temperature changes and surface water. This product is flexible, fade resistant and dries rapidly to a tough, long wearing color surface. It is a preferred coating for all walkways, overhangs, steps and other walking surfaces that require a non-slip surface. 31% <150 g/l sq. ft. Touch 30 minutes Re-coat 2-4 hours Green, red, blue, and dark green Line Marking Paint Smooth [TRC-037] Textured [TRC-038] Line Marking Paints are extremely high hiding, with one coat coverage. Carefully formulated with 100% acrylic emulsion for use on tennis courts, running tracks, basketball courts and other recreational areas. The use of Line Marking Paint results in clean, clear cut lines that stay permanent. Line Marking Paints are designed to give superior lines on all types of asphalt and acrylic surfaces and are recommended for use over all Colored Finish Coats. TRC-037 Textured Line Marking Paints create lines with the same bounce characteristics as the Colored Finish Coats. 38% <150 g/l sq. ft. Touch 30 minutes White Re-coat 2-4 hours 12

13 Notes: 13

14 Notes: 14

15 15

16 Complementary Coatings Corp. Garage Guard, Insl-Guard, Insl-X, Silathane, Silathane II, Sure-Step, and WaterBlock are registered trademarks of Complementary Coatings Corp. /M WI EA