EXTERIOR RESEARCH & DESIGN, LLC. Certificate of Authorization # Christian Street Oxford, CT PHONE: (203) FAX: (203)

Transcription

1 EVALUATION REPORT Johns Manville Corporation P.O. Box 5108 Denver, CO EXTERIOR RESEARCH & DESIGN, LLC. Certificate of Authorization # Christian Street Oxford, CT PHONE: (203) FAX: (203) Evaluation Report J R9 FL2948-R10 Date of Issuance: 03/28/2008 Revision 9: 08/28/2015 SCOPE: This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen, P.E. for use of the product under the Florida Building Code. The product described herein has been evaluated for compliance with the 5 th Edition (2014) Florida Building Code sections noted herein. DESCRIPTION: Johns Manville SBS Modified Bitumen Roof Systems LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein. CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the product changes or the referenced Quality Assurance documentation changes. Trinity ERD requires a complete review of this Evaluation Report relative to updated Code requirements with each Code Cycle. ADVERTISEMENT: The Evaluation Report number preceded by the words Trinity ERD Evaluated may be displayed in advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety. INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This Evaluation Report consists of pages 1 through 6, plus a 48-page Appendix. Prepared by: Robert J.M. Nieminen, P.E. Florida Registration 59166, Florida DCA ANE1983 The facsimile seal appearing was authorized by Robert Nieminen, P.E. on 08/28/2015. This does not serve as an electronically signed document. Signed, sealed hardcopies have been transmitted to the Product Approval Administrator and to the named client CERTIFICATION OF INDEPENDENCE: 1. Exterior Research & Design, LLC. d/b/a Trinity ERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or distributing products it evaluates. 2. Exterior Research & Design, LLC. d/b/a Trinity ERD is not owned, operated or controlled by any company manufacturing or distributing products it evaluates. 3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for which the evaluation reports are being issued. 4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the product. 5. This is a building code evaluation. Neither Trinity ERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose.

2 ROOFING SYSTEMS EVALUATION: 1. SCOPE: Product Category: Roofing Sub-Category: Modified Bitumen Roof Systems Compliance Statement: Johns Manville SBS Modified Bitumen Roof Systems, as produced by Johns Manville Corporation, have demonstrated compliance with the following sections of the Florida Building Code through testing in accordance with the following Standards. Compliance is subject to the Installation Requirements and Limitations / Conditions of Use set forth herein. 2. SNDARDS: Section Property Standard Year Wind FM Wind UL Impact FM Physical Properties ASTM D Physical Properties ASTM D Physical Properties ASTM D Physical Properties ASTM D Wind S REFERENCES: Entity Examination Reference Date ACRC (TST4671) S /30/2003 ACRC (TST4671) S /30/2003 ACRC (TST4671) S /04/2003 ACRC (TST4671) S /27/2006 ACRC (TST4671) S /27/2006 ACRC (TST4671) S /28/2006 ACRC (TST4671) S /18/2007 ERD (TST6049) Physical Properties /17/2005 ERD (TST6049) S /07/2007 ERD (TST6049) Physical Properties J /03/2007 ERD (TST6049) Physical Properties J /16/2009 ERD (TST6049) Physical Properties J /11/2010 ERD (TST6049) Physical Properties J /11/2010 ERD (TST6049) FM 4470/4474 J /16/2010 ERD (TST6049) FM 4470/4474 J /04/2011 FM Approvals (TST1867) FM 4470/4474 JM-SC /13/2014 FM Approvals (TST1867) FM 4470/4474 JM-SC /16/2015 FM Approvals (TST1867) FM 4470/4474 RAS-SC /16/2015 FM Approvals (TST1867) FM Q6A4.AM 12/11/1990 FM Approvals (TST1867) FM /11/1998 FM Approvals (TST1867) FM /11/1998 FM Approvals (TST1867) FM /10/1998 FM Approvals (TST1867) FM /01/1999 FM Approvals (TST1867) FM /02/2000 FM Approvals (TST1867) FM /19/2000 FM Approvals (TST1867) FM /13/2000 FM Approvals (TST1867) FM /15/2000 FM Approvals (TST1867) FM /04/2001 FM Approvals (TST1867) FM /10/2001 FM Approvals (TST1867) FM /04/2002 FM Approvals (TST1867) FM /04/2002 FM Approvals (TST1867) FM /03/2002 FM Approvals (TST1867) FM /25/2002 FM Approvals (TST1867) FM /05/2002 FM Approvals (TST1867) FM /02/2002 FM Approvals (TST1867) FM /21/2003 FM Approvals (TST1867) FM /05/2004 FM Approvals (TST1867) FM /09/2004 FM Approvals (TST1867) FM /30/2004 Exterior Research and Design, LLC. Certificate of Authorization #9503 Evaluation Report J R9 FL2948-R10 Revision 9: 08/28/2015 Page 2 of 6

3 Entity Examination Reference Date FM Approvals (TST1867) FM 4470/ /29/2004 FM Approvals (TST1867) FM 4470/ /21/2005 FM Approvals (TST1867) FM 4470/ /26/2006 FM Approvals (TST1867) FM 4470/ /18/2006 FM Approvals (TST1867) FM 4470/ /04/2006 FM Approvals (TST1867) FM 4470/ /15/2006 FM Approvals (TST1867) FM 4470/ /01/2006 FM Approvals (TST1867) FM 4470/ /22/2006 FM Approvals (TST1867) FM 4470/ /09/2007 FM Approvals (TST1867) FM 4470/ /21/2007 FM Approvals (TST1867) FM 4470/ /20/2009 FM Approvals (TST1867) FM 4470/ /10/2009 FM Approvals (TST1867) FM 4470/ /02/2009 FM Approvals (TST1867) FM 4470/ /02/2009 FM Approvals (TST1867) FM 4470/ /18/2011 FM Approvals (TST1867) FM 4470/ /23/2011 FM Approvals (TST1867) FM 4470/ /06/2012 FM Approvals (TST1867) FM 4470/ /04/2012 FM Approvals (TST1867) FM 4470/ /19/2012 FM Approvals (TST1867) FM 4470/ /03/2013 FM Approvals (TST1867) FM /04/2015 Madinah C&TC (TST9199) S 114 MCTC /02/2010 Madinah C&TC (TST9199) S 114 MCTC /12/2010 PRI (TST5878) Physical Properties JMC /15/2013 PRI (TST5878) FM 4470/4474 JMC /16/2013 PRI (TST5878) FM 4470/4474 JMC /16/2013 PRI (TST5878) FM 4470/4474 JMC /16/2013 PRI (TST5878) FM 4470/4474 JMC /16/2013 PRI (TST5878) Physical Properties JMC /17/2013 PRI (TST5878) FM 4470/4474 JMC /17/2013 PRI (TST5878) FM 4470/4474 JMC /17/2013 PRI (TST5878) FM 4470/4474 JMC /17/2013 PRI (TST5878) FM 4470/4474 JMC /19/2013 PRI (TST5878) FM 4470/4474 JMC /19/2013 PRI (TST5878) FM 4470/4474 JMC /13/2013 PRI (TST5878) FM 4470/4474 JMC /26/2015 PRI (TST5878) FM 4470/4474 JMC /22/2015 PRI (TST5878) UL 1897 JMC (A) 04/22/2015 PRI (TST5878) FM 4470/4474 JMC /14/2015 Miami-Dade (CER1592) S 114 Various NOAs Current UL, LLC (QUA9625) Quality Assurance Service Confirmation, R10167 Exp. 10/22/ PRODUCT DESCRIPTION: This Evaluation Report covers Johns Manville Modified Bitumen Roof Systems installed in accordance with Johns Manville published installation instructions and the Limitations / Conditions of Use herein. The following Johns Manville products make up the subject systems. Type Base / Ply Sheets BLE 1: ROLL-GOODS FOR JOHNS MANVILLE MODIFIED BITUMEN ROOF SYSTEMS Product Specification Reference Grade Type GlasPly IV ASTM D2178 N/A IV GlasPly Premier ASTM D2178 N/A VI GlasBase Plus ASTM D4601 N/A II PermaPly 28 ASTM D4601 N/A II JMCleanBond SBS Base ASTM D4601 N/A II JM BaseGrip SD/SA ASTM D4601 N/A II Ventsulation Felt ASTM D4897 N/A II Pro Proprietary N/A N/A Exterior Research and Design, LLC. Certificate of Authorization #9503 Evaluation Report J R9 FL2948-R10 Revision 9: 08/28/2015 Page 3 of 6

4 Type Smooth-Surfaced SBS Granule-Surfaced SBS Foil-Surfaced SBS BLE 1 (CONTINUED): ROLL-GOODS FOR JOHNS MANVILLE MODIFIED BITUMEN ROOF SYSTEMS Product Specification Reference Grade Type DynaPly T1 ASTM D6162 S I DynaBase ASTM D6163 S I DynaBase HW ASTM D6163 S I DynaWeld Base ASTM D6163 S I DynaBase XT ASTM D6163 S I DynaBase PR ASTM D6164 S I DynaFast 180 HW ASTM D6164 S I DynaFast 180 S ASTM D6164 S I DynaLastic 180 S ASTM D6164 S I DynaWeld 180 S ASTM D6164 S I DynaFast 250 HW ASTM D6164 S II DynaLastic 250 S ASTM D6164 S II DynaLastic 250 FR S ASTM D6164 S II DynaGrip Base SA/SD Proprietary N/A N/A DynaGrip Base SD/SA Proprietary N/A N/A DynaGrip Base SA/SA Proprietary N/A N/A DynaKap T1 ASTM D6162 G I DynaKap FR T1 ASTM D6162 G I DynaKap FR T1 CR ASTM D6162 G I DynaKap FR T1 CR G ASTM D6162 G I DynaMax FR ASTM D6162 G III DynaMax FR CR ASTM D6162 G III DynaMax FR CR G ASTM D6162 G III DynaGlas ASTM D6163 G I DynaGlas 30 FR ASTM D6163 G I DynaGlas 30 FR CR ASTM D6163 G I DynaGlas FR ASTM D6163 G I DynaGlas FR CR ASTM D6163 G I DynaGlas FR CR G ASTM D6163 G I DynaWeld Cap FR ASTM D6163 G I DynaWeld Cap FR CR ASTM D6163 G I DynaWeld Cap FR CR G ASTM D6163 G I DynaGlas 30 FR XT ASTM D6163 G I DynaGlas FR XT ASTM D6163 G I DynaGlas FR XT CR ASTM D6163 G I DynaGlas FR XT CR G ASTM D6163 G I JMCleanBond SBS Cap ASTM D6163 G I DynaLastic 180 ASTM D6164 G I DynaLastic 180 FR ASTM D6164 G I DynaLastic 180 FR CR ASTM D6164 G I DynaLastic 180 FR CR G ASTM D6164 G I DynaWeld Cap 180 ASTM D6164 G I DynaWeld Cap 180 CR ASTM D6164 G I DynaWeld Cap 180 FR ASTM D6164 G I DynaWeld Cap 180 FR CR ASTM D6164 G I DynaWeld Cap 180 FR CR G ASTM D6164 G I DynaLastic 250 ASTM D6164 G II DynaLastic 250 FR ASTM D6164 G II DynaLastic 250 FR CR ASTM D6164 G II DynaLastic 250 FR CR G ASTM D6164 G II DynaWeld Cap 250 ASTM D6164 G II DynaWeld Cap 250 CR ASTM D6164 G II DynaWeld Cap 250 FR ASTM D6164 G II DynaWeld Cap 250 FR CR ASTM D6164 G II DynaWeld Cap 250 FR CR G ASTM D6164 G II DynaGrip Cap Proprietary N/A N/A DynaClad ASTM D6298 N/A N/A DynaClad Copper ASTM D6298 N/A N/A Exterior Research and Design, LLC. Certificate of Authorization #9503 Evaluation Report J R9 FL2948-R10 Revision 9: 08/28/2015 Page 4 of 6

5 5. LIMITIONS: 5.1 This is a building code evaluation. Neither Trinity ERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. 5.2 This Evaluation Report is not for use in HVHZ. 5.3 Refer to a current Roofing Materials Directory for fire ratings of this product. 5.4 For steel deck installations, foam plastic insulation shall be separated from the building interior in accordance with FBC unless the exceptions stated in FBC and apply. 5.5 The roof system evaluation herein pertains to above-deck roof components. Roof decks and structural members shall be in accordance with FBC requirements to the satisfaction of the AHJ. Load resistance of the roof deck shall be documented through proper codified and/or FBC Approval documentation. 5.6 For recover installations, the existing roof shall be examined in accordance with FBC For mechanically attached insulation or membrane or strip-bonded insulation, the maximum design pressure for the selected assembly shall meet or exceed the Zone 1 design pressure determined in accordance with FBC Chapter 16. Zones 2 and 3 shall employ an attachment density designed by a qualified design professional to resist the elevated pressure criteria. Commonly used methods are RAS 117, FM LPDS 1-29 and ANSI/SPRI WD-1. Assemblies marked with an asterisk* carry the limitations set forth in Section (a) of FM LPDS 1-29 for Zone 2/3 enhancements. 5.8 For fully-adhered insulation, the maximum design pressure for the selected assembly shall meet or exceed critical design pressure determined in accordance with FBC Chapter 16. No rational analysis is permitted for these systems 5.9 For mechanically attached insulation or membrane over existing roof decks, fasteners shall be tested in the existing deck for withdrawal resistance. A qualified design professional shall review the data for comparison to the minimum requirements for the system. Testing and analysis shall be in accordance with S 105 or ANSI/SPRI FX For bonded insulation or membrane over existing substrates in a re-roof (tear off) or recover installation, the existing deck or existing roof surface shall be examined for compatibility with the adhesive to be installed. If any surface conditions exist that bring system performance into question, field uplift testing in accordance with ASTM E907, FM LPDS 1-52, ANSI/SPRI IA-1 or S 124 shall be conducted on mock-ups of the proposed new roof assembly For bonded insulation or membrane over existing substrates in a recover installation, the existing roof system shall be capable of resisting project design pressures on its own merit to the satisfaction of the AHJ, as documented through field uplift testing in accordance with ASTM E907, FM LPDS 1-52 or S Metal edge attachment (except gutters), shall be designed and installed for wind loads in accordance with FBC Chapter 16 and tested for resistance in accordance with ANSI/SPRI ES-1 or RAS 111, except the basic wind speed shall be determined from FBC Figure All products in the roof assembly shall have quality assurance audit in accordance with the FBC and F.A.C. Rule 61G INSLLATION: 6.1 Johns Manville SBS Modified Bitumen roof systems shall be installed in accordance with Johns Manville published installation instructions, subject to the Limitations / Conditions of Use noted below. 6.2 System attachment requirements for wind load resistance are set forth in Appendix 1. MDP = Maximum Design Pressure is the result of testing for wind load resistance based on allowable wind loads, and reflects the ultimate passing pressure divided by 2 (the 2 to 1 margin of safety per FBC has already been applied). Refer to FBC 1609 for determination of design wind loads. Exterior Research and Design, LLC. Certificate of Authorization #9503 Evaluation Report J R9 FL2948-R10 Revision 9: 08/28/2015 Page 5 of 6

6 7. BUILDING PERMIT REQUIREMENTS: As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of this product. 8. MANUFACTURING PLANTS: Contact the named QA entity for information on plants covered under F.A.C. Rule 61G20-3 QA requirements. 9. QUALITY ASSURANCE ENTITY: UL, LLC QUA9625; (414) ; - THE 48-PAGES TT FOLLOW FORM PART OF THIS EVALUATION REPORT - Exterior Research and Design, LLC. Certificate of Authorization #9503 Evaluation Report J R9 FL2948-R10 Revision 9: 08/28/2015 Page 6 of 6

7 APPENDIX 1: ATCHMENT REQUIREMENTS FOR WIND UPLIFT RESISNCE Table Application Type Description Page 1A-1 Wood New or Reroof (Tear-Off) A-2 Mech. Attached Anchor Sheet, Bonded Insulation, Bonded Roof Cover 4 1A-2 Wood New, Reroof (Tear-Off) or Recover A-2 Mech. Attached Anchor Sheet, Bonded Insulation, Bonded Roof Cover 4 1B Wood New, Reroof (Tear-Off) or Recover B Mech. Attached Base Insulation, Bonded Top Insulation, Bonded Roof Cover 5 1C Wood New, Reroof (Tear-Off) or Recover C Mech. Attached Insulation, Bonded Roof Cover 5 1D Wood New, Reroof (Tear-Off) or Recover D Prelim. Attached Insulation, Mech. Attached Base Sheet, Bonded Roof Cover 6 1E-1 Wood New, Reroof (Tear-Off) E Non-Insulated, Mech. Attached Base Sheet, Bonded Roof Cover 7 1E-2 Wood New, Reroof (Tear-Off) or Recover E Non-Insulated, Mech. Attached Base Sheet, Bonded Roof Cover 7 2A Steel or Conc. New, Reroof (Tear-Off) or Recover B Mech. Attached Base Insulation, Bonded Top Insulation, Bonded Roof Cover B Steel or Conc. New, Reroof (Tear-Off) or Recover C Mech. Attached Insulation, Bonded Roof Cover C Steel or Conc. New, Reroof (Tear-Off) or Recover D Prelim. Attached Insulation, Mech. Attached Base Sheet, Bonded Roof Cover A-1 New or Reroof (Tear-Off) A-1 Bonded Insulation, Bonded Roof Cover A-2 New or Reroof (Tear-Off) A-1 Bonded Temporary Roof, Bonded Insulation, Bonded Roof Cover 25 3B-1 New or Reroof (Tear-Off) F Non-Insulated, Bonded Roof Cover 26 3B-2 New or Reroof (Tear-Off) F Non-Insulated, Bonded Roof Cover, Paver System Overburden 26 4A-1 LWIC New or Reroof (Tear-Off) A-1 Bonded Insulation, Bonded Roof Cover A-2 LWIC New or Reroof (Tear-Off) A-2 Mech. Attached Anchor Sheet, Bonded Insulation, Bonded Roof Cover 30 4B LWIC New, Reroof (Tear-Off) or Recover C Mech. Attached Insulation, Bonded Roof Cover 31 4C-1 LWIC New or Reroof (Tear-Off) E Non-Insulated, Mech. Attached Base Sheet, Bonded Roof Cover C-2 LWIC New, Reroof (Tear-Off) or Recover E Mech. Attached Base Sheet, Bonded Roof Cover 36 4D-1 LWIC New or Reroof (Tear-Off) F Non-Insulated, Bonded Roof Cover 37 4D-2 LWIC New or Reroof (Tear-Off) F Non-Insulated, Bonded Roof Cover, Paver System Overburden 37 5A-1 CWF New or Reroof (Tear-Off) A-1 Bonded Insulation, Bonded Roof Cover 38 5A-2 CWF New, Reroof (Tear-Off) or Recover A-2 Mech. Attached Anchor Sheet, Bonded Insulation, Bonded Roof Cover 39 5B CWF New, Reroof (Tear-Off) or Recover B Mech. Attached Base Insulation, Bonded Top Insulation, Bonded Roof Cover 39 5C CWF New, Reroof (Tear-Off) or Recover C Mech. Attached Insulation, Bonded Roof Cover 40 5D CWF New, Reroof (Tear-Off) or Recover E Non-Insulated, Mech. Attached Base Sheet, Bonded Roof Cover 40 6A-1 Gypsum New or Reroof (Tear-Off) A-1 Bonded Insulation, Bonded Roof Cover 41 6A-2 Gypsum New, Reroof (Tear-Off) or Recover A-2 Mech. Attached Anchor Sheet, Bonded Insulation, Bonded Roof Cover B Gypsum New, Reroof (Tear-Off) or Recover B Mech. Attached Base Insulation, Bonded Top Insulation, Bonded Roof Cover 43 6C Gypsum New, Reroof (Tear-Off) or Recover C Mech. Attached Insulation, Bonded Roof Cover 44 6D Gypsum New, Reroof (Tear-Off) or Recover E Non-Insulated, Mech. Attached Base Sheet, Bonded Roof Cover 44 7 Various Recover A-1 Bonded Insulation, Bonded Roof Cover Various Summary of FBC EHPA Systems per SSTD The following notes apply to the systems outlined herein: 1. The evaluation herein pertains to above-deck roof components. Roof decks and structural members shall be in accordance with FBC requirements to the satisfaction of the AHJ. Load resistance of the roof deck shall be documented through proper codified and/or FBC Approval documentation. 2. Unless otherwise noted, fasteners and stress plates for insulation attachment shall be as follows. Fasteners shall be of sufficient length for the following engagements: Wood : UltraFast Fasteners or All Purpose Fasteners with UltraFast Metal Plates. Minimum 0.75-inch plywood penetration or minimum 1-inch wood plank embedment. Steel : UltraFast Fasteners or All Purpose Fasteners with UltraFast Metal Plates. Minimum 0.75-inch steel penetration and engage the top flute of the steel deck. : All Purpose Fasteners with UltraFast Metal Plates or Structural Fasteners with UltraFast Metal Plates (flat bottom only). Minimum 1-inch embedment. Fasteners installed with a pilot hole in accordance with the fastener manufacturer s published installation instructions. Prepared by: Robert Nieminen, PE Appendix 1, Page 1 of 48

8 3. Unless otherwise noted, insulation may be any one layer or combination of polyisocyanurate, polystyrene, wood fiberboard, perlite, gypsum-based roof board, that meets the QA requirements of F.A.C. Rule -3 and is documented as meeting FBC and, for foam plastic, FBC Chapter 26, when installed with the roof cover. 4. Minimum 200 psi, minimum 2-inch thick lightweight insulating concrete may be substituted for rigid insulation board for System Type D (mechanically attached base sheet, bonded roof cover), whereby the base sheet fasteners are installed through the LWIC to engage the structural steel or concrete deck. The structural deck shall be of equal or greater configuration to the steel and concrete deck listings. Roof decks and structural members shall be in accordance with FBC requirements to the satisfaction of the AHJ. Load resistance of the roof deck shall be documented through proper codified and/or FBC Approval documentation. 5. Unless otherwise noted, insulation adhesive application rates are as follows. Ribbon or bead width is at the time of application; the ribbons/beads shall expand as noted in the manufacturer s published instructions. Hot asphalt (): Full coverage at lbs/square JM MBR Bonding Adhesive (MBR-BA): Continuous 0.75-inch wide ribbons, 12-inch o.c. or full coverage at 2.0 gal/square JM Two-Part Urethane Insulation Adhesive (): Continuous 0.75-inch wide ribbons, 12-inch o.c. Note: JM Green Two-Part Urethane Insulation Adhesive may be used where is referenced. JM Roofing System Urethane Adhesive (RSUA): Continuous 0.5 to 0.75-inch wide ribbons, 12-inch o.c. 3M : Continuous 2.5 to 3.5-inch ribbons, 12-inch o.c. Note: When multiple layers(s) of insulation and/or coverboard are installed in ribbon-applied adhesive, adhesive ribbons shall be staggered from layer-to-layer a distance of one-half the ribbon spacing. Note: The maximum edge distance from the adhesive ribbon to the edge of the insulation board shall be not less than one-half the specified ribbons spacing 6. Unless otherwise noted, all insulations are flat stock or taper board of the minimum thickness noted. Tapered polyisocyanurate at the following thickness limitations may be substituted with the following Maximum Design Pressure (MDP) limitations. In no case shall these values be used to increase the MDP listings in the tables; rather if MDP listing below meets or exceeds that listed for a particular system in the tables, then the thinner board listed below may be used as a drop-in for the equivalent thicker material listed in the table: JM Two-Part Urethane Insulation Adhesive (): MDP psf (Min. 0.5-inch thick) JM Roofing System Urethane Adhesive (RSUA): MDP psf (Min. 0.5-inch thick) 3M : MDP psf (Min. 1.0-inch thick) 7. Bonded polyisocyanurate insulation boards shall be maximum 4 x 4 ft. 8. For mechanically attached components or partially bonded insulation, the maximum design pressure for the selected assembly shall meet or exceed the Zone 1 design pressure determined in accordance with FBC Chapter 16, and Zones 2 and 3 shall employ an attachment density designed by a qualified design professional to resist the elevated pressure criteria. Commonly used methods are RAS 117 and FM LPDS Assemblies marked with an asterisk* carry the limitations set forth in Section (a) of FM LPDS 1-29 for Zone 2/3 enhancements. 9. For fully bonded assemblies, the maximum design pressure for the selected assembly shall meet or exceed critical design pressure determined in accordance with FBC Chapter 16, and no rational analysis is permitted. 10. For mechanically attached components over existing decks, fasteners shall be tested in the existing deck for withdrawal resistance. A qualified design professional shall review the data for comparison to the minimum requirements for the system. Testing and analysis shall be in accordance with S 105 or ANSI/SPRI FX For existing substrates in a bonded recover installation, the existing roof surface shall be examined for compatibility and bond performance with the selected adhesive, and the existing roof system shall be capable of resisting project design pressures on its own merit to the satisfaction of the AHJ, as documented through field uplift testing in accordance with ASTM E907, FM LPDS 1-52, ANSI/SPRI IA-1 or S For Recover Applications using System Type D, the insulation is optional; however, the existing roof system shall be suitable for a recover application. 13. LWIC shall be cast in accordance with FBC Section 1917 to the satisfaction of the Authority Having Jurisdiction. For systems where specific LWIC is referenced, refer to current LWIC Product Approval for specific deck construction and limitations. For systems where specific LWIC is not referenced, the minimum design mix shall be 300 psi. In all cases, the minimum top-coat thickness is 2-inches. For LWIC over, reference is made to FBC Section , Point Unless otherwise noted, refer to the following references for bonded base, ply or cap sheet applications. JOHNS MANVILLE ROOF COVERS Reference Layer Material Application BP-AA (Base and Ply sheets, Asphalt-Applied) BP-CA1 (Base and Ply sheets, Cold-Applied, 1-part) Base GlasBase Plus, PermaPly 28 Ply GlasPly IV, GlasPly Premier, GlasBase Plus, PermaPly 28 Base or Ply GlasBase Plus, PermaPly 28 Hot asphalt at lbs/square JM MBR Cold Application Adhesive at 1.5 to 2.0 gal/square Prepared by: Robert Nieminen, PE Appendix 1, Page 2 of 48

9 JOHNS MANVILLE ROOF COVERS (CONTINUED) Reference Layer Material Application BP- (Base and Ply sheets, Cold-Applied, 2-part) BP- (Base and Ply sheets, Cold-Applied, 1-part) SBS-AA (SBS, Asphalt-Applied) SBS-CA1 (SBS, Cold-Applied, 1- part) SBS- (SBS, Cold-Applied, 2- part) SBS- (SBS, Cold-Applied, 1- part) (SBS, Torch-Applied) SBS-SA (SBS, self-adhering) Base or Ply GlasBase Plus, PermaPly 28 Base or Ply Base or Ply: Cap Base or Ply: Cap Base or Ply: Cap Note: Base or Ply: Cap Base or Ply: Cap Base or Ply: Cap GlasBase Plus, PermaPly 28, GlasPly IV, GlasPly Premier DynaPly T1, DynaBase, DynaBase XT, DynaBase PR, DynaLastic 180 S, DynaLastic 250 S, DynaLastic 250 FR S DynaPly T1, DynaKap T1, DynaKap FR T1, DynaKap FR T1 CR, DynaKap FR T1 CR G, DynaGlas, DynaGlas FR, DynaGlas FR XT, DynaGlas FR XT CR, DynaGlas FR XT CR G, DynaGlas FR CR, DynaGlas FR CR G, DynaGlas 30 FR, DynaGlas 30 FR CR, DynaGlas 30 FR, DynaGlas 30 FR CR XT, DynaLastic 180 S, DynaLastic 250 S, DynaLastic 250 FR S, DynaLastic 180, DynaLastic 180 FR, DynaLastic 180 FR CR, DynaLastic 180 FR CR G, DynaLastic 250, DynaLastic 250 FR, DynaLastic 250 FR CR, DynaLastic 250 FR CR G, DynaMax FR, DynaMax FR CR, DynaMax FR CR G DynaPly T1, DynaBase, DynaBase XT, DynaBase PR, DynaLastic 180 S, DynaLastic 250 S, DynaLastic 250 FR S DynaPly T1, DynaKap T1, DynaKap FR T1, DynaKap FR T1 CR, DynaKap FR T1 CR G, DynaGlas, DynaGlas FR, DynaGlas FR XT, DynaGlas FR XT CR, DynaGlas FR XT CR G, DynaGlas FR CR, DynaGlas FR CR G, DynaGlas 30 FR, DynaGlas 30 FR CR, DynaGlas 30 FR, DynaGlas 30 FR CR XT, DynaLastic 180 S, DynaLastic 250 S, DynaLastic 250 FR S, DynaLastic 180, DynaLastic 180 FR, DynaLastic 180 FR CR, DynaLastic 180 FR CR G, DynaLastic 250, DynaLastic 250 FR, DynaLastic 250 FR CR, DynaLastic 250 FR CR G, DynaMax FR, DynaMax FR CR, DynaMax FR CR G DynaPly T1, DynaBase, DynaBase XT, DynaBase PR, DynaLastic 180 S, DynaLastic 250 S, DynaLastic 250 FR S DynaPly T1, DynaKap T1, DynaKap FR T1, DynaKap FR T1 CR, DynaKap FR T1 CR G, DynaGlas, DynaGlas FR, DynaGlas FR XT, DynaGlas FR XT CR, DynaGlas FR XT CR G, DynaGlas FR CR, DynaGlas FR CR G, DynaGlas 30 FR, DynaGlas 30 FR CR, DynaGlas 30 FR, DynaGlas 30 FR CR XT, DynaLastic 180 S, DynaLastic 250 S, DynaLastic 250 FR S, DynaLastic 180, DynaLastic 180 FR, DynaLastic 180 FR CR, DynaLastic 180 FR CR G, DynaLastic 250, DynaLastic 250 FR, DynaLastic 250 FR CR, DynaLastic 250 FR CR G, DynaMax FR, DynaMax FR CR, DynaMax FR CR G SBS- applications shall not be mixed with SBS-AA applications DynaPly T1, DynaBase, DynaBase XT, DynaBase PR, DynaLastic 180 S, DynaLastic 250 S, DynaLastic 250 FR S DynaPly T1, DynaKap T1, DynaKap FR T1, DynaKap FR T1 CR, DynaKap FR T1 CR G, DynaGlas, DynaGlas FR, DynaGlas FR XT, DynaGlas FR XT CR, DynaGlas FR XT CR G, DynaGlas FR CR, DynaGlas FR CR G, DynaGlas 30 FR, DynaGlas 30 FR CR, DynaGlas 30 FR, DynaGlas 30 FR CR XT, DynaLastic 180 S, DynaLastic 250 S, DynaLastic 250 FR S, DynaLastic 180, DynaLastic 180 FR, DynaLastic 180 FR CR, DynaLastic 180 FR CR G, DynaLastic 250, DynaLastic 250 FR, DynaLastic 250 FR CR, DynaLastic 250 FR CR G, DynaMax FR, DynaMax FR CR, DynaMax FR CR G DynaBase HW, DynaWeld Base, DynaWeld 180 S DynaWeld Cap FR, DynaWeld Cap FR CR, DynaWeld Cap FR CR G, DynaWeld Cap 180, DynaWeld Cap 180 CR, DynaWeld Cap 180 FR, DynaWeld Cap 180 FR CR, DynaWeld Cap 180 FR CR G, DynaWeld Cap 250, DynaWeld Cap 250 CR, DynaWeld Cap 250 FR, DynaWeld Cap 250 FR CR, DynaWeld Cap 250 FR CR G, DynaClad, DynaClad Copper DynaGrip Base SD/SA, DynaGrip Base SA/SA, JMCleanBond SBS Base Sheet DynaGrip Cap, JMCleanBond SBS Cap Sheet 15. MDP = Maximum Design Pressure is the result of testing for wind load resistance based on allowable wind loads. Refer to FBC 1609 for determination of design wind loads. JM MBR Bonding Adhesive at 1.5 to 2.0 gal/square JM Premium Cold App at 1.5 to 2.0 gal/square Hot asphalt at lbs/square JM MBR Cold Application Adhesive at 1.5 to 2.0 gal/square JM MBR Bonding Adhesive at 1.5 to 2.0 gal/square JM Premium Cold App at 1.5 to 2.0 gal/square Torch-Applied Self-Adhering Prepared by: Robert Nieminen, PE Appendix 1, Page 3 of 48

10 W-1 W-2 W-3 Min. 15/32-inch plywood at max. 24-inch spans Min. 15/32-inch plywood at max. 24-inch spans Min. 19/32-inch plywood at max. 24-inch spans BLE 1A-1: WOOD DECKS NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-2: MECNICALLY ATCHED ANCHOR SHEET, BONDED INSULATION, BONDED ROOF COVER Anchor Sheet Base Insulation Top Insulation Roof Cover MDP Type Fasteners Attach Type Attach Type Attach Base Ply Cap PermaPly 28, DynaBase, GlasBase Plus or Ventsulation Two plies of PermaPly 28, DynaBase, GlasBase Plus or Ventsulation GlasPly Premier, PermaPly 28 or Ventsulation 32 ga., 1-5/8- inch diameter tin caps with 11 ga. annular ring shank nails 32 ga., 1-5/8- inch diameter tin caps with 11 ga. annular ring shank nails 32 ga., 1-5/8- inch diameter tin caps with 11 ga. annular ring shank nails 9-inch o.c. in 4- inch lap and 12- inch o.c. in three, equally spaced, staggered center rows 9-inch o.c. in 4- inch lap and 12- inch o.c. in two, equally spaced, staggered center rows 9-inch o.c. in 4- inch lap and 9- inch o.c. in two, equally spaced, staggered center rows (Optional) Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25 PSI AGF or CGF, ValuTherm AGF or CGF, ValuTherm 25 PSI AGF or CGF (Optional) Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25 PSI AGF or CGF, ValuTherm AGF or CGF, ValuTherm 25 PSI AGF or CGF (Optional) Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25 PSI AGF or CGF, ValuTherm AGF or CGF, ValuTherm 25 PSI AGF or CGF Min inch Fesco Board, min. 0.5-inch Retro-Fit Board, RetroPlus Board or DuraBoard or min. 1.5-inch Fesco Foam or DuraFoam Min inch Fesco Board, min. 0.5-inch Retro-Fit Board, RetroPlus Board or DuraBoard or min. 1.5-inch Fesco Foam or DuraFoam Min inch Fesco Board, min. 0.5-inch Retro-Fit Board, RetroPlus Board or DuraBoard or min. 1.5-inch Fesco Foam or DuraFoam, SBS- AA or SBS-, SBS- AA or SBS-, SBS- AA or SBS- (Optional) SBS-AA or (Optional) SBS- or (Optional) SBS- or SBS- or SBS- or SBS- or System W-4 Min. 19/32-inch plywood at max. 24-inch spans BLE 1A-2: WOOD DECKS NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE A-2: MECNICALLY ATCHED ANCHOR SHEET, BONDED INSULATION, BONDED ROOF COVER Anchor Sheet Base Insulation Top Insulation Roof Cover MDP Type Fasteners Attach Type Attach Type Attach Base Ply Cap GlasPly Premier, PermaPly 28 or Ventsulation 8-inch o.c. in 4- inch lap and 8- inch o.c. in three, equally spaced, staggered center rows (Optional) Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25 PSI AGF or CGF, ValuTherm AGF or CGF, ValuTherm 25 PSI AGF or CGF Min inch Fesco Board, min. 0.5-inch Retro-Fit Board, RetroPlus Board or DuraBoard or min. 1.5-inch Fesco Foam or DuraFoam, SBS- AA or SBS- (Optional) SBS- or SBS- or Prepared by: Robert Nieminen, PE Appendix 1, Page 4 of 48

11 BLE 1B: WOOD DECKS NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B: MECNICALLY ATCHED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER System W-5 W-6 W-7 Min. 19/32-inch plywood at max. 24-inch spans Min. 19/32-inch plywood at max. 24-inch spans Min. 19/32-inch plywood at max. 24-inch spans Base Insulation Layer Top Insulation Layer Roof Cover MDP Type Fasteners Attach Type Attach Base Ply Cap Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, 1 per 2 Min inch Fesco Board, min. 0.5-inch Retro-Fit Board, RetroPlus Board or min. 1.5-inch Fesco Foam 2 Min. 0.5-inch 1 per 2 ft DuraBoard 1 per 1.33 Min. 0.5-inch DuraBoard or MBR-BA full coverage, SBS-AA or SBS-, SBS-AA or SBS- AA, BP- or (Optional) SBS- AA, BP- or SBS- or SBS- or BLE 1C: WOOD DECKS NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C: MECNICALLY ATCHED INSULATION, BONDED ROOF COVER System Base Insulation Layer Top Insulation Layer Roof Cover MDP Type Fasteners Attach Base Ply Cap W-8 Min. 19/32-inch plywood at max. 24-inch spans Min. 0.5-inch Retro-Fit Board, RetroPlus Board or DuraBoard, min inch Fesco Board or min inch Fesco Foam or DuraFoam 1 per 2 SBS-AA or SBS-, BP- SBS- or or W-9 Min. 19/32-inch plywood at max. 24-inch spans Min. 0.5-inch DuraBoard 1 per 2 (Optional) W-10 Min. 19/32-inch plywood at max. 24-inch spans Min inch DuraBoard 1 per 1.33, SBS- or SBS-, Prepared by: Robert Nieminen, PE Appendix 1, Page 5 of 48

12 BLE 1D: WOOD DECKS NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE D: PRELIMINARILY ATCHED INSULATION, MECNICALLY ATCHED BASE SHEET, BONDED ROOF COVER System (See Note ) Slip Sheet Insulation Layer(s) Base Sheet Roof Cover MDP Type Attach Base Fasteners Attach Ply Cap W-11 Min. 19/32-inch plywood at max. 24- inch spans (Optional) One or more layers PermaPly 28, loose laid below or above insulation One or more layers, any combination Looselaid DynaBase High Load Fasteners through 1-inch wide JM Polymer Membrane Batten 9-inch o.c. within the min. 4-inch wide, heat-welded side laps. (Optional) SBS- AA or SBS-AA or -37.5* W-12 Min. 15/32-inch plywood at max. 24- inch spans (Optional) One or more layers PermaPly 28, loose laid below or above insulation One or more layers, any combination Looselaid DynaFast 180 HW or DynaFast 250 HW High Load Fasteners and JM APB Plates or High Load Plates 18-inch o.c. within the min. 4-inch wide, heatwelded side laps. (Optional) SBS- W-13 Min. 19/32-inch plywood at max. 24- inch spans (Optional) One or more layers PermaPly 28, loose laid below or above insulation One or more layers, any combination Prelim Attach GlasPly Premier, PermaPly 28 or Ventsulation 8-inch o.c. at min. 4-inch lap and 8-inch o.c. at three, equally spaced, staggered center rows AA, BP- SBS- AA, SBS- or or SBS W-14 Min. 15/32-inch plywood at max. 24- inch spans (Optional) One or more layers PermaPly 28, loose laid below or above insulation One or more layers, min. 1-inch, any combination Looselaid DynaFast 180 HW or DynaFast 250 HW High Load Fasteners and JM APB Plates or High Load Plates 9-inch o.c. within the min. 4-inch wide, heat-welded side laps. (Optional) SBS W-15 Min. 15/32-inch plywood at max. 24- inch spans (Optional) One or more layers PermaPly 28, loose laid below or above insulation One or more layers, min. 1-inch, any combination Looselaid DynaFast 180 HW or DynaFast 250 HW High Load LH through 1- inch wide JM Polymer Membrane Batten 6-inch o.c. within the min. 4-inch wide, heat-welded side laps. (Optional) SBS Prepared by: Robert Nieminen, PE Appendix 1, Page 6 of 48

13 W-16 W-17 Min. 19/32-inch plywood at max. 24-inch spans Min. 19/32-inch plywood at max. 24-inch spans BLE 1E-1: WOOD DECKS NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE E: NON-INSULATED, MECNICALLY ATCHED BASE SHEET, BONDED ROOF COVER Two plies of PermaPly 28, DynaBase, GlasBase Plus or Ventsulation Base Sheet Roof Cover MDP Base Fasteners Attach Ply Cap GlasPly Premier, PermaPly 28 or Ventsulation 32 ga., 1-5/8-inch diameter tin caps with 11 ga. annular ring shank nails 32 ga., 1-5/8-inch diameter tin caps with 11 ga. annular ring shank nails 9-inch o.c. in 4-inch lap and 12- inch o.c. in two, equally 9-inch o.c. in 4-inch lap and 9- inch o.c. in two, equally BP- or BP- or or or BLE 1E-2: WOOD DECKS NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE E: NON-INSULATED, MECNICALLY ATCHED BASE SHEET, BONDED ROOF COVER System Slip Sheet Base Sheet Roof Cover MDP Base Fasteners Attach Ply Cap W-18 Min. 19/32-inch plywood at max. 24-inch spans (Optional) One or more layers PermaPly 28, loose laid DynaBase High Load Fasteners through 1-inch wide JM Polymer Membrane Batten 9-inch o.c. within the min. 4- inch wide, heat-welded side laps. (Optional) SBS-AA or SBS-AA or SBS * W-19 Min. 15/32-inch plywood at max. 24-inch spans (Optional) One or more layers PermaPly 28, loose laid DynaFast 180 HW or DynaFast 250 HW High Load Fasteners and JM APB Plates or High Load Plates 18-inch o.c. within the min. min. 4-inch wide, heat-welded side laps. (Optional) W-20 Min. 19/32-inch plywood at max. 24-inch spans (Optional) One or more layers PermaPly 28, loose laid GlasPly Premier, PermaPly 28 or Ventsulation 8-inch o.c. in 4-inch lap and 8- inch o.c. in three, equally BP- or or Prepared by: Robert Nieminen, PE Appendix 1, Page 7 of 48

14 S-1 S-2 S-3 S-4 S-5 S-6 S-7 BLE 2A: STEEL OR CONCRETE DECKS NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B: MECNICALLY ATCHED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER Base Insulation Layer Top Insulation Layer Roof Cover MDP Type Fasten Attach Type Attach Base Ply Cap Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, Min. 1.5-inch ENRGY 3, ValuTherm. Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, 1 per Min. 0.5-inch RetroPlus 5.33 Board 1 per Min. 0.5-inch RetroPlus 5.33 Board 1 per Min. 0.5-inch SECUROCK 5.33 or MBR-BA, full coverage 1 per 2 2 Min. 0.5-inch DuraBoard MBR-BA ft 1 per 2 1 per 2 1 per 2 One or more layers base insulation followed by min. 0.5-inch DuraBoard or min. 0.5-inch DuraBoard MBR-BA CA1, BP-, BP-, CA1, SBS-, SBS- CA1, BP-, BP-, CA1, SBS-, SBS- CA1, BP-, BP-, CA1, SBS-, SBS- BP-CA1, BP-, BP-, SBS- CA1, SBS- or SBS- BP-CA1, BP-, BP-, SBS- CA1, SBS- or SBS- BP-CA1, BP-, BP-, SBS-CA1, SBS-, SBS- BP-CA1, BP-, BP-, SBS-CA1, SBS-, SBS- BP-CA1, BP-, BP-, SBS-CA1, SBS-, SBS- CA1, BP-, BP-, SBS-CA1, SBS- or SBS- CA1, BP-, BP-, SBS-CA1, SBS- or SBS- CA1, SBS-, SBS- CA1, SBS-, SBS- CA1, SBS-, SBS-, SBS-CA1, SBS- or SBS-CA-3 SBS-CA1, SBS- or SBS-CA * -37.5* -37.5* (Optional) RSUA (Optional) Prepared by: Robert Nieminen, PE Appendix 1, Page 8 of 48

15 S-8 S-9 S-10 S-11 S-12 S-13 S-14 BLE 2A: STEEL OR CONCRETE DECKS NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B: MECNICALLY ATCHED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER Base Insulation Layer Top Insulation Layer Roof Cover MDP Type Fasten Attach Type Attach Base Ply Cap Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, Min. 1.5-inch ENRGY 3, ValuTherm. Min. 2-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, Min. 2-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, 1 per 2 Min inch Invinsa Roof Board or min. 1.5-inch Invinsa Foam or RSUA DynaGrip SD/SA (Optional) 1 per 2 2 Min. 0.5-inch DuraBoard (Optional) ft 1 per 4 1 per 4 1 per 4 Min. 0.5-inch RetroPlus Board Min. 0.5-inch RetroPlus Board Min. 0.5-inch SECUROCK 1 per Min. 0.5-inch RetroPlus 5.33 Board 1 per Min. 0.5-inch RetroPlus 5.33 Board or MBR-BA, full coverage or MBR-BA, full coverage CA1, BP-, BP-, CA1, SBS-, SBS- CA1, BP-, BP-, CA1, SBS-, SBS- CA1, BP-, BP-, CA1, SBS-, SBS- CA1, BP-, BP-, CA1, SBS-, SBS- CA1, BP-, BP-, CA1, SBS-, SBS- BP-CA1, BP-, BP-, SBS-CA1, SBS-, SBS- BP-CA1, BP-, BP-, SBS-CA1, SBS-, SBS- BP-CA1, BP-, BP-, SBS-CA1, SBS-, SBS- BP-CA1, BP-, BP-, SBS-CA1, SBS-, SBS- BP-CA1, BP-, BP-, SBS-CA1, SBS-, SBS- CA1, SBS-, SBS- CA1, SBS-, SBS- CA1, SBS-, SBS-, CA1, SBS-, SBS- CA1, SBS-, SBS- Prepared by: Robert Nieminen, PE Appendix 1, Page 9 of 48

16 S-15 S-16 S-17 S-18 S-19 S-20 S-21 BLE 2A: STEEL OR CONCRETE DECKS NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B: MECNICALLY ATCHED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER Base Insulation Layer Top Insulation Layer Roof Cover MDP Type Fasten Attach Type Attach Base Ply Cap Min. 2-inch ENRGY 3, ValuTherm. Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25,, Fesco Foam or DuraFoam Min. 1.5-inch ENRGY 3, ValuTherm. Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25,, Fesco Foam or DuraFoam Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, Min. 2-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, 1 per Min. 0.5-inch SECUROCK per 2 Min. 0.5-inch Retro-Fit Board, RetroPlus Board or DuraBoard, min inch Fesco Board (flat or tapered) or min. 1.5-inch Fesco Foam or DuraFoam 1 per Min. 0.5-inch SECUROCK per 1.78 Min. 0.5-inch Retro-Fit Board, RetroPlus Board or DuraBoard or min. 1.5-inch Fesco Foam or DuraFoam 1 per Min. 0.5-inch RetroPlus 1.78 Board 1 per Min. 0.5-inch RetroPlus 1.78 Board 1 per 2 Min. 3/8-inch SECUROCK or MBR-BA, full coverage or CA1, BP-, BP-, CA1, SBS-, SBS-, SBS-AA or SBS- CA1, BP-, BP-, CA1, SBS-, SBS-, SBS-AA or SBS- CA1, BP-, BP-, CA1, SBS-, SBS- CA1, BP-, BP-, CA1, SBS-, SBS-, SBS-SA or BP-CA1, BP-, BP-, SBS-CA1, SBS-, SBS- or BP-CA1, BP-, BP-, SBS-CA1, SBS-, SBS- or BP-CA1, BP-, BP-, SBS-CA1, SBS-, SBS- BP-CA1, BP-, BP-, SBS-CA1, SBS-, SBS-, BP-AA,, SBS-SA or SBS- CA1, SBS-, SBS-,,, CA1, SBS-, SBS-, or SBS- CA1, SBS-, SBS- CA1, SBS-, SBS- SBS-,, SBS-SA or Prepared by: Robert Nieminen, PE Appendix 1, Page 10 of 48

17 S-22 S-23 S-24 S-25 S-26 S-27 S-28 BLE 2A: STEEL OR CONCRETE DECKS NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B: MECNICALLY ATCHED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER Base Insulation Layer Top Insulation Layer Roof Cover MDP Type Fasten Attach Type Attach Base Ply Cap Min. 2-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, Min. 1.5-inch ENRGY 3, ValuTherm. Min. 2-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25,, Fesco Foam or DuraFoam Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, 1 per 2 Min. 3/8-inch SECUROCK 1 per Min. 0.5-inch RetroPlus 1.33 Board 1 per Min. 0.5-inch RetroPlus 1.33 Board 1 per Min. 0.5-inch SECUROCK per per 1 1 per 1 Min. 0.5-inch Retro-Fit Board, RetroPlus Board or DuraBoard or min. 1.5-inch Fesco Foam or DuraFoam Min. 0.5-inch RetroPlus Board Min. 0.5-inch RetroPlus Board RSUA, 6- inch o.c. or MBR-BA, full coverage or MBR-BA, full coverage, SBS-SA or CA1, BP-, BP-, CA1, SBS-, SBS- CA1, BP-, BP-, CA1, SBS-, SBS- CA1, BP-, BP-, CA1, SBS-, SBS-, SBS-AA or SBS- CA1, BP-, BP-, CA1, SBS-, SBS- CA1, BP-, BP-, CA1, SBS-, SBS-, BP-AA,, SBS-SA or SBS- BP-CA1, BP-, BP-, SBS-CA1, SBS-, SBS- BP-CA1, BP-, BP-, SBS-CA1, SBS-, SBS- BP-CA1, BP-, BP-, SBS-CA1, SBS-, SBS- BP- SBS- or BP-CA1, BP-, BP-, SBS-CA1, SBS-, SBS- BP-CA1, BP-, BP-, SBS-CA1, SBS-, SBS- SBS-,, SBS-SA or CA1, SBS-, SBS- CA1, SBS-, SBS- CA1, SBS-, SBS-, or SBS- CA1, SBS-, SBS- CA1, SBS-, SBS Prepared by: Robert Nieminen, PE Appendix 1, Page 11 of 48

18 S-29 S-30 S-31 S-32 BLE 2A: STEEL OR CONCRETE DECKS NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B: MECNICALLY ATCHED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER Base Insulation Layer Top Insulation Layer Roof Cover MDP Type Fasten Attach Type Attach Base Ply Cap Min. 1.5-inch ENRGY 3, ValuTherm. Min. 2-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, Min. 2-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, Min. 2-inch ENRGY 3, ValuTherm. 1 per 1 Min. 0.5-inch SECUROCK 1 per Min. 0.5-inch RetroPlus 1.45 Board 1 per Min. 0.5-inch RetroPlus 1.45 Board 1 per Min. 0.5-inch SECUROCK inch o.c. or MBR-BA, full coverage 4-inch o.c. CA1, BP-, BP-, CA1, SBS-, SBS- CA1, BP-, BP-, CA1, SBS-, SBS- CA1, BP-, BP-, CA1, SBS-, SBS- CA1, BP-, BP-, CA1, SBS-, SBS- BP-CA1, BP-, BP-, SBS-CA1, SBS-, SBS- BP-CA1, BP-, BP-, SBS-CA1, SBS-, SBS- BP-CA1, BP-, BP-, SBS-CA1, SBS-, SBS- BP-CA1, BP-, BP-, SBS-CA1, SBS-, SBS- CA1, SBS-, SBS-, CA1, SBS-, SBS- CA1, SBS-, SBS- CA1, SBS-, SBS-, -90.0* * Prepared by: Robert Nieminen, PE Appendix 1, Page 12 of 48

19 BLE 2B: STEEL OR CONCRETE DECKS NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C: MECNICALLY ATCHED INSULATION, BONDED ROOF COVER System Base Insulation Layer Top Insulation Layer Roof Cover MDP Type Fasteners Attach Base Ply Cap S-33 Grade 33 steel or Min inch Invinsa Roof Board UltraFast (steel only) or All Purpose with UltraFast Metal (round) Plates 2 BP- or SBS- 1 per 2 ft or SBS- SBS * S-34 Grade 33 steel or (Optional) One or more layers, any Min inch Invinsa Foam UltraFast (steel only) or All Purpose with UltraFast Metal (round) Plates 2 BP- or SBS- 1 per 2 ft or SBS- SBS * S-35 Grade 33 steel or Gypsum- Fiber Roof Board (square plates) 1 per 2.67 DynaGrip Base SD/SA or (Optional) -37.5* S-36 Grade 33 steel or Gypsum- Fiber Roof Board (square plates) 1 per 2.67 CA1, BP-, BP-CA-3 CA1, SBS-, SBS- BP- CA1, BP-, BP-CA- 3 CA1, SBS-, SBS- SBS-CA1, SBS-, SBS * S-37 Grade 33 steel or Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25 PSI AGF or CGF, ValuTherm AGF or CGF, ValuTherm 25 UltraFast (steel only) or All Purpose with UltraFast Metal (round) Plates 1 per 2 BP- orsbs- or SBS- SBS- S-38 Grade 33 steel or Min. 0.5-inch DuraBoard 1 per 2 BP-, SBS-CA1, SBS- or SBS- BP-CA1, BP-, CA1, BP-, BP-, SBS- CA1, SBS- or SBS- SBS-CA1, SBS- or SBS- CA-3 S-39 Grade 33 steel or Min. 0.5-inch DuraBoard 1 per 2 (Optional) S-40 Grade 33 steel or (Optional) One or more layers, any Min. 2-inch ENRGY 3 Foil Face or min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, or FescoFoam (perlite side down) 1 per 2 SBS-SA (Optional) SBS-SA or SBS-SA or Prepared by: Robert Nieminen, PE Appendix 1, Page 13 of 48

20 BLE 2B: STEEL OR CONCRETE DECKS NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C: MECNICALLY ATCHED INSULATION, BONDED ROOF COVER System Base Insulation Layer Top Insulation Layer Roof Cover MDP Type Fasteners Attach Base Ply Cap S-41 Grade 33 steel or (Optional) One or more layers, any Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI 2 JM BaseGrip 1 per 2 ft SD/SA (Optional) S-42 Grade 33 steel or (Optional) One or more layers, any Min. 2-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25, 1 per 4 DynaGrip SD/SA (Optional) S-43 Grade 33 steel or Min inch Invinsa Roof Board UltraFast (steel only) or All Purpose with UltraFast Plastic Plates 1 per 2 SBS-SA (Optional) S-44 Grade 33 steel or (Optional) One or more layers, any Min inch Invinsa Foam UltraFast (steel only) or All Purpose with UltraFast Plastic Plates 1 per 2 SBS-SA (Optional) S-45 Grade 33 steel or Min inch SECUROCK Gypsum- Fiber Roof Board (square plates) 1 per 2.67 DynaGrip Base SD/SA or (Optional) S-46 Grade 33 steel or Min inch SECUROCK Gypsum- Fiber Roof Board (square plates) 1 per 2.67 CA1, BP-, BP-CA-3 CA1, SBS-, SBS- BP- CA1, BP-, BP-CA- 3 CA1, SBS-, SBS- SBS-CA1, SBS-, SBS- S-47 Grade 33 steel or Min. 0.5-inch Retro-Fit Board or DuraBoard, min inch Fesco Board or min. 1.5-inch Fesco Foam or DuraFoam 2 BP-AA, SBS-AA or 1 per 2 ft SBS- or SBS-,SBS-, S-48 Grade 33 steel or Min 2inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25,, UltraFast (steel only) 1 per 1.78 SBS-SA (Optional) SBS-SA or S-49 Grade 33 steel or (Optional) One or more layers, any Min. 1.5-inch ENRGY 3, R-Panel, ENRGY 3 25 PSI, R-Panel 25 PSI, ENRGY 3 AGF or CGF, ENRGY 3 25 PSI AGF or CGF, ValuTherm AGF or CGF, ValuTherm 25 1 per 1.33 BP- or SBS- or SBS- SBS Prepared by: Robert Nieminen, PE Appendix 1, Page 14 of 48