B. Illuminated: Illuminated by lighting source integrally constructed as part of the sign unit.

Transcription

1 SECTION PANEL SIGNAGE PART 1 - GENERAL 1.I RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section Includes: 1. Room-identification signs B. Related Requirements: 1. Section "Temporary Facilities and Controls" for temporary Project identification signs and for temporary information and directional signs. 2. Div. I 5 "ldentification for Plumbing Piping and Equipment" for labels, tags, and nameplates for plumbing systems and equipment. 3. Div. 15 "ldentification for HVAC Piping and Equipment" for labels, tags, and nameplates for HVAC systems and equipment. 4. Div. 16 "Electrical Identification" for labels, tags, and nameplates for electrical equipment. 5. Div. 16 "Interior Lighting" for illuminated, self-luminous, and photoluminescent exit sign units. 1.3 DEFINITIONS A. Accessible: In accordance with the accessibility standard. B. Illuminated: Illuminated by lighting source integrally constructed as part of the sign unit. 1.4 COORDINATION A. Furnish templates for placement of sign-anchorage devices embedded in permanent construction by other installers. 3. Furnish templates for placement of electrical service embedded in permanent construction by other installers 1.5 ACTION SUBMITTALS A. Product Data: For each type of product. B. Shop Drawings: For panel signs. 1, Include fabrication and installation details and attachments to other work. PANEL SIGNAGE 101 7

2 2. Show sign mounting heights, locations of supplementary supports to be provided by others, and accessories. 3. Show message list, typestyles, graphic elements and layout for each sign at least half size. 4. Coordinate locations of electrical service connections for signage furnished by others. 5. Include diagrams for power, signal, and control wiring. C. Samples for Initial Selection: For each type of sign assembly, exposed component, and exposed finish. 1, Include representative Samples of available typestyles and graphic symbols. D. Sign Schedule: Use same designations specified or indicated on Drawings or in a sign schedule. 1.6 INFORMATIONAL SUBMITTALS A. Sample Warranty: For special warranty. 1.7 CLOSEOUT SUBMITTALS A. Maintenance Data: For signs to include in maintenance manuals. 1.8 WARRANTY A. Special Warranty: Manufacturer agrees to repair or replace components of signs that fail in materials or workmanship within specified warranty period. 1. Failures include, but are not limited to, the following: a. Deterioration of finishes beyond normal weathering. b. Deterioration of embedded graphic image. c. Separation or delamination of sheet materials and components. 2. Warranty Period: Five years from date of Substantial Completion. PART 2 - PRODUCTS 2.1 PERFORMANCE REQUIREMENTS A. Accessibility Standard: Comply with applicable provisions in the U.S. Architectural & Transportation Barriers Compliance Board's ADA-ABA Accessibility Guidelines for Buildings and Facilities and ICC A for signs. B. Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intended location and application. PANEL SIGNAGE

3 SIGNS Manufacturers: Subject to compliance with requirements, available manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following: Ace Sign Systems, Inc. Advance Corporation; Braille-Tac Division. Allen Industries, Inc. Allen Markings International. APCO Graphics, Inc. ASE, Inc. AS1 Sign Systems, Inc. Best Sign Systems Inc. Bunting Graphics, Inc. Clarke Systems. Diskey Sign Company. lnpro Corporation. Mohawk Sign Systems. Nelson-Harkins Industries. Poblocki Sign Company, LLC. Seton Identification Products. Supersine Company (The); Division of Stamp-Rite, Inc. Vista System. Vomar Products, Inc. Room-Identification Sign: Sign with smooth, uniform surfaces; with message and characters having uniform faces, sharp corners, and precisely formed lines and profiles; and as follows: 1. Laminated-Sheet Sign: Photopolymer face sheet with raised graphics laminated to acrylic backing sheet to produce composite sheet. a. Composite-Sheet Thickness: inch. b. Color(s): As selected by Architect from manufacturer's full range. 2. Mounting: Manufacturer's standard method for substrates indicated. 3. Text and Typeface: Accessible raised characters and Braille with typeface as selected by Architect from manufacturer's full range and variable content as scheduled. Finish raised characters to contrast with background color, and finish Braille to match background color. PANEL-SIGN MATERIALS Acrylic Sheet: ASTM D 4802, category as standard with manufacturer for each sign, Type UVF (UV filtering). Polycarbonate Sheet: ASTM C 1349, AppendixXI, Type ll (coated, mar-resistant, UVstabilized polycarbonate), with coating on both sides. PVC Sheet: Manufacturer's standard, UV-light stable, PVC plastic. PANEL SIGNAGE

4 ACCESSORIES D. Fasteners and Anchors: Manufacturer's standard as required for secure anchorage of signage, noncorrosive and compatible with each material joined, and complying with the following: 1. Use concealed fasteners and anchors unless indicated to be exposed. E. Adhesives: As recommended by sign manufacturer and with a VOC content of 70 g/l or less for adhesives used inside the weatherproofing system and applied on-site when calculated according to 40 CFR 59, Subpart D (EPA Method 24). F. Two-Face Tape: Manufacturer~s standard high-bond, foam-core tape, inch (1.I4 mm) thick, with adhesive on both sides. G. Hook-and-Loop Tape: Manufacturer's standard two-part tape consisting of hooked part on sign back and looped side on mounting surface. H. Bituminous Paint: Cold-applied asphalt emulsion complying with ASTM D FABRICATION A. General: Provide manufacturer's standard sign assemblies according to requirements indicated. 1. Preassemble signs and assemblies in the shop to greatest extent possible. Disassemble signs and assemblies only as necessary for shipping and handling limitations. Clearly mark units for reassembly and installation; apply markings in locations concealed from view after final assembly. 2. Mill joints to a tight, hairline fit. Form assemblies and joints exposed to weather to resist water penetration and retention. 3. Comply with AWS for recommended practices in welding and brazing. Provide welds and brazes behind finished surfaces without distorting or discoloring exposed side. Clean exposed welded and brazed connections of flux, and dress exposed and contact surfaces. 4. Conceal connections if possible; otherwise, locate connections where they are inconspicuous. 5. Internally brace signs for stability and for securing fasteners. 6. Provide rebates, lugs, and brackets necessary to assemble components and to attach to existing work. Drill and tap for required fasteners. Use concealed fasteners where possible; use exposed fasteners that match sign finish. B. Surface-Engraved Graphics: Machine engrave characters and other graphic devices into panel surface indicated to produce precisely formed copy, incised to uniform depth. 1. Engraved Metal: Fill engraved graphics with manufacturer's standard baked enamel. 2. Engraved Opaque Acrylic Sheet: Fill engraved graphics with manufacturer's standard enamel. 3. Face-Engraved Clear Acrylic Sheet: Fill engraved copy with manufacturer's standard enamel. Apply manufacturer's standard opaque background color coating to back face of acrylic sheet. 4. Engraved Plastic Laminate: Engrave through exposed face ply of plastic-laminate sheet to expose contrasting core ply. PANEL SIGNAGE

5 C. Subsurface-Applied Graphics: Apply graphics to back face of clear face-sheet material to produce precisely formed image. Image shall be free of rough edges. D. Subsurface-Engraved Graphics: Reverse engrave back face of clear face-sheet material. Fill resulting copy with manufacturer's standard enamel. Apply opaque manufacturer's standard background color coating over enamel-filled copy. E. Shop- and Subsurface-Applied Vinyl: Align vinyl film in final position and apply to surface. Firmly press film from the middle outward to obtain good bond without blisters or fishmouths. 2.5 GENERAL FINISH REQUIREMENTS A. Protect mechanical finishes on exposed surfaces from damage by applying a strippable, temporary protective covering before shipping. B. Appearance of Finished Work: Noticeable variations in same piece are not acceptable. Variations in appearance of adjoining components are acceptable if they are within the range of approved Samples and are assembled or installed to minimize contrast. PART 3 - EXECUTION 3.1 EXAMINATION A. Examine substrates, areas, and conditions, with Installer present, for compliance with requirements for installation tolerances and other conditions affecting performance of signage work. 3. Verify that sign-support surfaces are within tolerances to accommodate signs without gaps or irregularities between backs of signs and support surfaces unless otherwise indicated. C. Verify that anchor inserts are correctly sized and located to accommodate signs. D. Verify that electrical service is correctly sized and located to accommodate signs. E. Proceed with installation only after unsatisfactory conditions have been corrected. INSTALLATION A. General: Install signs using mounting methods indicated and according to manufacturer's written instructions. 1. Install signs level, plumb, true to line, and at locations and heights indicated, with sign surfaces free of distortion and other defects in appearance. 2. Install signs so they do not protrude or obstruct according to the accessibility standard. 3. Before installation, verify that sign surfaces are clean and free of materials or debris that would impair installation. 4. Corrosion Protection: Coat concealed surfaces of exterior aluminum in contact with grout, concrete, masonry, wood, or dissimilar metals, with a heavy coat of bituminous paint. PANEL SIGNAGE

6 B. Room-Identification Signs and Other Accessible Signage: Install in locations on walls as indicated and according to accessibility standard. C. Mounting Methods: Adhesive: Clean bond-breaking materials from substrate surface and remove loose debris. Apply linear beads or spots of adhesive symmetrically to back of sign and of suitable quantity to support weight of sign after cure without slippage. Keep adhesive away from edges to prevent adhesive extrusion as sign is applied and to prevent visibility of cured adhesive at sign edges. Place sign in position, and push to engage adhesive. Temporarily support sign in position until adhesive fully sets. Two-Face Tape: Clean bond-breaking materials from substrate surface and remove loose debris. Apply tape strips symmetrically to back of sign and of suitable quantity to support weight of sign without slippage. Keep strips away from edges to prevent visibility at sign edges. Place sign in position, and push to engage tape adhesive. Hook-and-Loop Tape: Clean bond-breaking materials from substrate surface and remove loose debris. Apply sign component of two-part tape strips symmetrically to back of sign and of suitable quantity to support weight of sign without slippage; push to engage tape adhesive. Keep tape strips inch away from edges to prevent visibility at sign edges when sign is initially installed or reinstalled. Apply substrate component of tape to substrate in locations aligning with tape on back of sign; push and rub well to fully engage tape adhesive to substrate. D. Signs Mounted on Glass: Provide opaque sheet matching sign material and finish onto opposite side of glass to conceal back of sign. 3.3 ADJUSTING AND CLEANING A. Remove and replace damaged or deformed signs and signs that do not comply with specified requirements. Replace signs with damaged or deteriorated finishes or components that cannot be successfully repaired by finish touchup or similar minor repair procedures. B. Remove temporary protective coverings and strippable films as signs are installed. C. On completion of installation, clean exposed surfaces of signs according to manufacturer's written instructions, and touch up minor nicks and abrasions in finish. Maintain signs in a clean condition during construction and protect from damage until acceptance by Owner. 3.4 SIGN SCHEDULE A. Provide 8 x 8" ADA accessible signage with raised characters, braille, and graphic designation at the following locations: a. MEN'S RESTROOM (1 17) WOMEN'S RESTROOM (1 14) 3. Provide 4"x 8" signage with raised characters and Braille at the following locations: a. MECHANICAL (1 15) END OF SECTION PANEL SIGNASE

7 SECTION TOILET COMPARTMENTS PART 1 - GENERAL 1.I RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section. 1.2 SUMMARY A. This Section includes solid-polymer units as follows: 1. Toilet Enclosures: Overhead braced and Floor anchored. 2. Urinal Screens: Wall hung. B. Related Sections include the following: 1. Division 6 Section "Rough Carpentry" for blocking and overhead support of floor-andceiling-anchored units. 2. Division 10 "Toilet and Bath Accessories" for toilet tissue dispensers, grab bars, and similar accessories. 1.3 SUBMITTALS A. Product Data: For each type of product indicated, Include construction details, material descriptions, dimensions of individual components and profiles, and finishes. B. Shop Drawings: Include plans, elevations, sections, details, and attachments to other work. 1. Show locations of cutouts for compartment-mounted toilet accessories. C. Samples for Initial Selection: For each type of unit indicated. D. Samples for Verification: Of each type of color and finish required for units, prepared on &inchsquare Samples of same thickness and material indicated for Work. 1.4 QUALITY ASSURANCE A. Comply with requirements in CID-A-A-60003, "Partitions, Toilets, Complete." 1.5 PROJECT CONDITIONS A. Field Measurements: Verify actual locations of walls, columns, ceilings, and other construction contiguous with toilet compartments by field measurements before fabrication and indicate measurements on Shop Drawings. TOILET COMPARTMENTS

8 1. Established Dimensions: Where field measurements cannot be made without delaying the Work, establish dimensions and proceed with fabricating toilet compartments without field measurements. Coordinate wall, floor, ceilings, and other contiguous construction to ensure that actual dimensions correspond to established dimensions. PART 2 - PRODUCTS 2.1 SOLID-POLYMER UNITS A. Available Manufacturers: Subject to compliance with requirements, manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following: 1. Ampco. 2. Capitol Partitions, Inc. 3. Comtec Industries. 4. General Partitions Mfg. Corp, 5. Global Steel Products Corp. 6. Metpar Corp. 7. Santana Products, Inc. B. Door, Panel, and Pilaster Construction: Solid, high-density polyethylene (HDPE) panel material, not less than 1 inch thick, seamless, with eased edges, and with homogenous color and pattern throughout thickness of material. 1. Color and Pattern: One color for each room as selected by Architect from manufacturer's full range of colors and patterns. C. Pilaster Shoes and Sleeves (Caps): Manufacturer's standard design; stainless steel D. Brackets (Fittings): 1. Stirrup Type: Ear or U-brackets, stainless steel. E. Heat-Sink Strip: Manufacturer's standard continuous, extruded-aluminum strip fastened to exposed bottom edges of solid-polymer components to prevent burning. F. Overhead Cross Bracing for Ceiling-Hung Units: As recommended by manufacturer and fabricated from solid polymer. 2.2 ACCESSORIES A. Hardware and Accessories: Manufacturer's standard design, heavy-duty operating hardware and accessories. 1. Material: Stainless steel. B. Overhead Bracing: Manufacturer's standard continuous, extruded-aluminum head rail with antigrip profile and in manufacturer's standard finish. C. Anchorages and Fasteners: Manufacturer's standard exposed fasteners of stainless steel or chrome-plated steel or brass, finished to match hardware, with theft-resistant-type heads. TOILET COMPARTMENTS

9 Provide sex-type bolts for through-bolt applications. For concealed anchors, use hot-dip galvanized or other rust-resistant, protective-coated steel. FABRICATION Overhead-Braced Units: Provide manufacturer's standard corrosion-resistant supports, leveling mechanism, fasteners, and anchors at pilasters to suit floor conditions. Make provisions for setting and securing continuous head rail at top of each pilaster. Provide shoes at pilasters to conceal supports and leveling mechanism. Floor-Anchored Units: Provide manufacturer's standard corrosion-resistant anchoring assemblies complete with threaded rods, lock washers, and leveling adjustment nuts at pilasters for structural connection to floor. Provide shoes at pilasters to conceal anchorage. Doors: Unless otherwise indicated, provide 24-inch- wide in-swinging doors for standard toilet compartments and 36-inch- wide out-swinging doors with a minimum 32-inch- wide clear opening for compartments indicated to be accessible to people with disabilities. 1. Hinges: Manufacturer's standard self-closing type that can be adjusted to hold doors open at any angle up to 90 degrees. 2. Latch and Keeper: Manufacturer's standard recessed latch unit designed for emergency access and with combination rubber-faced door strike and keeper. Provide units that comply with accessibility requirements of authorities having jurisdiction at compartments indicated to be accessible to people with disabilities. 3. Coat Hook: Manufacturer's standard combination hook and rubber-tipped bumper, sized to prevent door from hitting compartment-mounted accessories. 4. Door Bumper: Manufacturer's standard rubber-tipped bumper at out-swinging doors. 5. Door Pull: Manufacturer's standard unit at out-swinging doors that complies with accessibility requirements of authorities having jurisdiction. Provide units on both sides of doors at compartments indicated to be accessible to people with disabilities. PART 3 - EXECUTION INSTALLATION General: Comply with manufacturer's written installation instructions. Install units rigid, straight, level, and plumb. Secure units in position with manufacturer's recommended anchoring devices. 1. Maximum Clearances: a. Pilasters and Panels: 112 inch. b. Panels and Walls: 1 inch. 2. Stirrup Brackets: Secure panels to walls and to pilasters with not less than two brackets attached near top and bottom of panel. a. Locate wall brackets so holes for wall anchors occur in masonry or tile joints. b. Align brackets at pilasters with brackets at walls. Overhead-Braced Units: Secure pilasters to floor and level, plumb, and tighten. Secure continuous head rail to each pilaster with not less than two fasteners. Hang doors to align tops TOILET COMPARTMENTS

10 of doors with tops of panels and adjust so tops of doors are parallel with overhead brace when doors are in closed position. C. Floor-Anchored Units: Set pilasters with anchors penetrating not less than 2 inches into structural floor, unless otherwise indicated in manufacturer's written instructions. Level, plumb, and tighten pilasters. Hang doors and adjust so tops of doors are level with tops of pilasters when doors are in closed position. D. Wall-Hung Urinal Screens: Attach with anchoring devices to suit supporting structure. Set units level and plumb and to resist lateral impact. 3.2 ADJUSTING A. Hardware Adjustment: Adjust and lubricate hardware according to manufacturer's written instructions for proper operation. Set hinges on in-swinging doors to hold doors open approximately 30 degrees from closed position when unlatched. Set hinges on out-swinging doors to return doors to fully closed position. END OF SECTION TOILET COMPARTMENTS

11 SECTION TOILET, BATH, AND LAUNDRY ACCESSORIES PART 1 - GENERAL 1.I RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section Includes: 1. Public-use washroom accessories. 2. Childcare accessories. 3. Underlavatory guards. 4. Custodial accessories. 1.3 ACTION SUBMITTALS A. Product Data: For each type of product indicated. Include the following: 1. Construction details and dimensions. 2. Anchoring and mounting requirements, including requirements for cutouts in other work and substrate preparation. 3. Material and finish descriptions. 4. Features that will be included for Project. 5. Manufacturer's warranty. 0. Samples: Full size, for each accessory item to verify design, operation, and finish requirements. C. Product Schedule: Indicating types, quantities, sizes, and installation locations by room of each accessory required. 1, ldentify locations using room designations indicated. 2. ldentify products using designations indicated. 1.4 INFORMATIONAL SUBMITTALS A. Warranty: Sample of special warranty. 1.5 CLOSEOUT SUBMITTALS A. Maintenance Data: For toilet and bath accessories to include in maintenance manuals. TOILET, BATH, AND LAUNDRY ACCESSORIES 101 7

12 1.6 QUALITY ASSURANCE A. Source Limitations: For products listed together in the same Part 2 articles, obtain products from single source from single manufacturer. B. Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intended location and application. 1.7 COORDINATION A. Coordinate accessory locations with other work to prevent interference with clearances required for access by people with disabilities, and for proper installation, adjustment, operation, cleaning, and servicing of accessories. B. Deliver inserts and anchoring devices set into concrete or masonry as required to prevent delaying the Work. 1.8 WARRANTY A. Special Mirror Warranty: Manufacturer's standard form in which manufacturer agrees to replace mirrors that develop visible silver spoilage defects and that fail in materials or workmanship within specified warranty period. 1. Warranty Period: 15 years from date of Substantial Completion. PART 2 - PRODUCTS 2.1 MATERIALS A. Stainless Steel: ASTM A 666, Type 304, inch minimum nominal thickness unless otherwise indicated. B. Brass: ASTM B 19, flat products; ASTM B 16lB 16M, rods, shapes, forgings, and flat products with finished edges; or ASTM B 30, castings. C. Steel Sheet: ASTM A 10081A 1008M, Designation CS (cold rolled, commercial steel), inch minimum nominal thickness. D. Galvanized-Steel Sheet: ASTM A 653lA 653M, with G60 hot-dip zinc coating. E. Galvanized-Steel Mounting Devices: ASTM A 153lA 153M, hot-dip galvanized after fabrication. F. Fasteners: Screws, bolts, and other devices of same material as accessory unit and tamperand-theft resistant where exposed, and of galvanized steel where concealed. G. Chrome Plating: ASTM B 456, Service Condition Number SC 2 (moderate service). H. Mirrors: ASTM C 1503, Mirror Glazing Quality, clear-glass mirrors, nominal 6.0 mm thick. I. ABS Plastic: Acrylonitrile-butadiene-styrene resin formulation. TOILET, BATH, AND LAUNDRY ACCESSORIES 101 7

13 2.2 WASHROOM ACCESSORIES Basis-of-Design Product: Subject to compliance with requirements, provide product indicated on Drawings or comparable product by one of the following: 1. A & J Washroom Accessories, Inc. 2. American Specialties, Inc. 3. Bobrick Washroom Equipment, Inc 4. Bradley Corporation. (Basis of Design) 5. GAMCQ Specialty Accessories; a division of Bobrick Washroom Equipment, Inc. 6. Tubular Specialties Manufacturing, Inc. Toilet Tissue (Roll) Dispenser: 1. Basis-of-Design Product: Bradley 5402 Combination Towel (Folded) DispenserIWaste Receptacle: 1. Basis-of-Design Product: Bradley Liquid-Soap Dispenser: 1. Basis-of-Design Product: Bradley 6562 Grab Bar: 1. Basis-of-Design Product: Bradley 81 2 Series; size as indicated on drawings. Sanitary-Napkin Disposal Unit: 1. Basis-of-Design Product: Bradley Mirror Unit: 1. Basis-of-Design Product: Bradley 780 CHILDCARE ACCESSORIES See Editing Instruction No. 1 in the Evaluations for cautions about naming manufacturers. Retain one of first two paragraphs and list of manufacturers below. See Section "Product Requirements." Manufacturers: Subject to compliance with requirements, available manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following: Basis-of-Design Product: Subject to compliance with requirements, provide product indicated on Drawings or comparable product by one of the following: 1. American Specialties, Inc. 2. Brocar Products, Inc. 3. Diaper Deck & Company, Inc. 4. GAMCO Specialty Accessories; a division of Bobrick Washroom Equipment, Inc. 5. Koala Kare Products; a division of Bobrick Washroom Equipment, Inc. (BASIS OF DESIGN) TOILET, BATH, AND LAUNDRY ACCESSORIES 101 7

14 6. SSC, Inc. 7. Tubular Specialties Manufacturing, Inc. Diaper-Changing Station: 1. Basis-of-Design Product: Koala Kare KB200 UNDERLAVATORY GUARDS Manufacturers: Subject to compliance with requirements, available manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following: Basis-of-Design Product: Subject to compliance with requirements, provide product indicated on Drawings or comparable product by one of the following: 1. Plumberex Specialty Products, Inc. 2. Truebro by IPS Corporation. (BASIS OF DESIGN) Underlavatory Guard: 1. Basis-of-Design Product: Trubro pipe cover type 2. Description: Insulating pipe covering for supply and drain piping assemblies that prevent direct contact with and burns from piping; allow service access without removing coverings. 3. Material and Finish: Antimicrobial, molded plastic, Color to be selected by Architect from manufacturers full range. CUSTODIAL ACCESSORIES Manufacturers: Subject to compliance with requirements, available manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following: Basis-of-Design Product: Subject to compliance with requirements, provide product indicated on Drawings or comparable product by one of the following: 1. A & J Washroom Accessories, Inc. 2. American Specialties, Inc. 3. Bobrick Washroom Equipment, Inc. 4. Bradley Corporation. (BASIS OF DESIGN) 5. GAMCO Specialty Accessories; a division of Bobrick Washroom Equipment, Inc. 6. Tubular Specialties Manufacturing, Inc. Mop and Broom Holder: 1. Basis-of-Design Product: Bradley 9955 FABRICATION General: Fabricate units with tight seams and joints, and exposed edges rolled. Hang doors and access panels with full-length, continuous hinges. Equip units for concealed anchorage and with corrosion-resistant backing plates. TOILET, BATH, AND LAUNDRY ACCESSORIES 101 7

15 B. Keys: Provide universal keys for internal access to accessories for servicing and resupplying. Provide minimum of six keys to Owner's representative. PART 3 - EXECUTION 3.1 INSTALLATION A. Install accessories according to manufacturers' written instructions, using fasteners appropriate to substrate indicated and recommended by unit manufacturer. Install units level, plumb, and firmly anchored in locations and at heights indicated. B. Grab Bars: Install to withstand a downward load of at least 250 Ibf, when tested according to ASTM F ADJUSTING AND CLEANING A. Adjust accessories for unencumbered, smooth operation. Replace damaged or defective items. B. Remove temporary labels and protective coatings. C. Clean and polish exposed surfaces according to manufacturer's written recommendations. END OF SECTION TOILET, BATH, AND LAUNDRY ACCESSORIES 1017

16

17 SECTION FIRE PROTECTION SPECIALTIES PART 1 - GENERAL 1.I RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section. 1.2 SUMMARY A. This Section includes the following: 1. Portable fire extinguishers. 2. Fire-protection cabinets for portable fire extinguishers. 3. Surface mounted brackets for portable fire extinguishers. 1.3 SUBMITTALS A. Product Data: Include construction details, material descriptions, dimensions of individual components and profiles, and finishes for fire-protection cabinets. 1. Fire Extinguishers: Include rating and classification. 2. Fire-Protection Cabinets: lnclude roughing-in dimensions, details showing mounting methods, relationships of box and trim to surrounding construction, door hardware, cabinet type, trim style, and panel style. B. Maintenance Data: For fire extinguishers and fire-protection cabinets to include in maintenance manuals. 1.4 QUALITY ASSURANCE A. Source Limitations: Obtain fire extinguishers and fire-protection cabinets through one source from a single manufacturer. B. NFPA Compliance: Fabricate and label fire extinguishers to comply with NFPA 10, "Portable Fire Extinguishers." C. Fire Extinguishers: Listed and labeled for type, rating, and classification by an independent testing agency acceptable to authorities having jurisdiction. 1.5 COORDINATION A. Coordinate size of fire-protection cabinets to ensure that type and capacity of fire extinguishers indicated are accommodated. FIRE PROTECTION SPECIALTIES

18 A. Special Warranty: Manufacturer's standard form in which manufacturer agrees to repair or replace components of portable fire extinguishers that fail in materials or workmanship within specified warranty period. 1. Failures include, but are not limited to, the following: a. Failure of hydrostatic test according to NFPA 10. b. Faulty operation of valves or release levers. 2. Warranty Period: Six years from date of Substantial Completion. PART 2 - PRODUCTS 2.1 MANUFACTURERS A. In other Part 2 articles where titles below introduce lists, the following requirements apply to product selection: 1. Available Manufacturers: Subject to compliance with requirements, manufacturers offering products that may be incorporated into the Work include, but are not limited to, manufacturers specified. 2.2 MATERIALS A. Cold-Rolled Steel Sheet: ASTM A 1008lA 1008M, Commercial Steel (CS), Type B. B. Tempered Float Glass: ASTM C 1048, Kind FT, Condition A, Type I, Quality q3, 3 mm thick, Class 1 (clear). 2.3 PORTABLE FIRE EXTINGUISHERS A. Available Manufacturers: 1. JL Industries, Inc. 2. Kidde Fyrnetics. 3. Larsen's Manufacturing Company. B. General: Provide fire extinguishers of type, size, and capacity for each fire-protection cabinet and mounting bracket indicated. 1. Valves: Manufacturer's standard. 2. Handles and Levers: Manufacturer's standard. 3. Instruction Labels: Include pictorial marking system complying with NFPA 10, Appendix B. C. Multipurpose Dry-Chemical Type in Steel Container FE-1: UL-rated 4-A:60-B:C, 10-lb nominal capacity, with monoammonium phosphate-based dry chemical in enameled-steel container. FIRE PROTECTION SPECIALTIES

19 FIRE-PROTECTION CABINET Available Manufacturers: 1. JL Industries, Inc. 2. Kidde Fyrnetics. 3. Larsen's Manufacturing Company. Cabinet Type: Suitable for fire extinguisher. Cabinet Construction: Rated per adjacent wall construction. Cabinet Material: Enameled-steel sheet. 1. Shelf: Same metal and finish as cabinet. Semi-recessed Cabinet: Cabinet box partially recessed in walls of shallow depth to suit style of trim indicated; with one-piece combination trim and perimeter door frame overlapping surrounding wall surface with exposed trim face and wall return at outer edge (backbend). 1. Rolled-Edge Trim: inch backbend depth Cabinet Trim Material: Steel sheet. Door Material: Steel sheet. Door Style: Fully glazed panel with frame. Door Glazing: Tempered float glass (clear). Door Hardware: Manufacturer's standard door-operating hardware of proper type for cabinet type, trim style, and door material and style indicated. 1. Provide projecting door pull and friction latch. 2. Provide continuous hinge, of same material and finish as trim, or concealed hinge permitting door to open 180 degrees. Accessories: 1. Mounting Bracket: Manufacturer's standard steel, designed to secure fire extinguisher to fire-protection cabinet, of sizes required for types and capacities of fire extinguishers indicated, with plated or baked-enamel finish. Finishes: 1. Manufacturer's standard baked-enamel paint for the following: a. Exterior of cabinet, door, and trim, except for those surfaces indicated to receive another finish. b, Interior of cabinet and door. 2. Steel: Baked enamel, color and texture as selected by Architect from manufacturer's full range. FIRE PROTECTION SPECIALTIES

20 2.5 FABRICATION A. Fire-Protection Cabinets: Provide manufacturer's standard box (tub), with trim, frame, door, and hardware to suit cabinet type, trim style, and door style indicated. 1. Weld joints and grind smooth. 2. Construct fire-rated cabinets with double walls fabricated from inch- thick, coldrolled steel sheet lined with minimum 518-inch- thick, fire-barrier material. a. Provide factory-drilled mounting holes. 3. Cabinet Doors: Fabricate doors according to manufacturer's standards, from materials indicated and coordinated with cabinet types and trim styles selected. 1. Fabricate door frames with tubular stiles and rails and hollow-metal design, minimum 112 inch thick. 2. Miter and weld perimeter door frames. C. Cabinet Trim: Fabricate cabinet trim in one piece with corners mitered, welded, and ground smooth. 2.6 FINISHES, GENERAL A. Comply with NAAMM's "Metal Finishes Manual for Architectural and Metal Products" for recommendations for applying and designating finishes. B. Protect mechanical finishes on exposed surfaces from damage by applying a strippable, temporary protective covering before shipping. C. Finish fire-protection cabinets after assembly. D. Appearance of Finished Work: Variations in appearance of abutting or adjacent pieces are acceptable if they are within one-half of the range of approved Samples. Noticeable variations in the same piece are not acceptable. Variations in appearance of other components are acceptable if they are within the range of approved Samples and are assembled or installed to minimize contrast. 2.7 STEEL FINISHES A. Surface Preparation: Clean surfaces of dirt, oil, grease, mill scale, rust, and other contaminants that could impair paint bond using manufacturer's standard methods. B. Baked-Enamel Finish: Immediately after cleaning and pretreating, apply manufacturer's standard two-coat, baked-enamel finish consisting of prime coat and thermosetting topcoat. Comply with paint manufacturer's written instructions for applying and baking to achieve a minimum dry film thickness of 2 mils. PART 3 - EXECUTION 3.1 EXAMINATION A. Examine walls and partitions for suitable framing depth and blocking where semirecessed cabinets will be installed. FIRE PROTECTION SPECIALTIES

21 B. Examine fire extinguishers for proper charging and tagging, 1. Remove and replace damaged, defective, or undercharged units. C. Proceed with installation only after unsatisfactory conditions have been corrected. 3.2 PREPARATION A. Prepare recesses for semirecessed fire-protection cabinets as required by type and size of cabinet and trim style. 3.3 INSTALLATION A. General: Install fire-protection specialties in locations and at mounting heights indicated or, if not indicated, at heights indicated below. 1. Fire-Protection Cabinets: 54 inches above finished floor to top of cabinet. 2. Mounting Brackets: 54 inches above finished floor to top of fire extinguisher B. Fire-Protection Cabinets: Fasten fire-protection cabinets to structure, square and plumb. 1. Unless otherwise indicated, provide recessed fire-protection cabinets. If wall thickness is not adequate for recessed cabinets, provide semirecessed fire-protection cabinets. 2. Provide inside latch and lock for break-glass panels. 3. Fasten mounting brackets to inside surface of fire-protection cabinets, square and plumb. 3.4 ADJUSTING AND CLEANING A. Remove temporary protective coverings and strippable films, if any, as fire-protection specialties are installed, unless otherwise indicated in manufacturer's written installation instructions. B. Adjust fire-protection cabinet doors to operate easily without binding. Verify that integral locking devices operate properly. C. On completion of fire-protection cabinet installation, clean interior and exterior surfaces as recommended by manufacturer. D. Touch up marred finishes, or replace fire-protection cabinets that cannot be restored to factoryfinished appearance. Use only materials and procedures recommended or furnished by fireprotection cabinet manufacturer. E. Replace fire-protection cabinets that have been damaged or have deteriorated beyond successful repair by finish touchup or similar minor repair procedures. END OF SECTION FIRE PROTECTION SPECIALTIES

22